Craftsman 113178200 User Manual 16 GALLON HOME N SHOP VAC Manuals And Guides L0903557
CRAFTSMAN Wet/Dry Vacuum Manual L0903557 CRAFTSMAN Wet/Dry Vacuum Owner's Manual, CRAFTSMAN Wet/Dry Vacuum installation guides
User Manual: Craftsman 113178200 113178200 CRAFTSMAN CRAFTSMAN 16 GALLON HOME-N-SHOP VAC - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 16 GALLON HOME-N-SHOP VAC #113178200. Home:Vacuums & Floor Care Parts:Craftsman Parts:Craftsman CRAFTSMAN 16 GALLON HOME-N-SHOP VAC Manual
Open the PDF directly: View PDF 
.
Page Count: 12
MODEL NO,
113o178200
Serial
number
Model and serial
number may be found
on the motor cover.
You should record both
model and serial
number in a safe place
for future use.
CAUTmON:
Read all safety
instructions carefufly
16 GALLON
HOME-N-SHOP VA C
WET AND DRY PiCK
®assembly'
®operating
•repair parts
UP
Sold by SEARS, ROEBUCK. ANO CO., Chicago, _L. 6068_ L!.SA
Part No. 73149
FULL ONE YEAR WARRANTY ON CRAFTSMAN HOME-N-SHOP VACSo
if within one year from date of purchase, this Craftsman Home-N-Shop Vac fails due to a
defect in material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTmNG THE NEAREST SEARS
STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state tO state.
SEARS, ROEBUCK AND CO., Sears Tower, BSC 41-3, Chicago, IL 60684
SAFETY INSTRUCT! ONS
Rules for Safe Operation
1. Know Your Vac.
Read and understand the owners manual and
labels affixed to the vac. Learn its applications
and limitations as welt as the specific potential
hazards peculiar to this vac.
2. Use the proper extension cord to prevent fires
and wiring damage.
NOTE: The use of any Extension Cord will cause
some loss of power. To keep the loss to a
minimum and to prevent overheating and motor
burnout, use the table below for the MINIMUM
wire size Extension Cord.
Extension Cord Length Wire Size
0- 50 Feet No. 14
50- 100 Feet No. 12
Use only three wire extension cords which have
3-prong grounding type plugs and 3-pole
receptacle that will accept the plug on your VAC.
3. WARNING: To avoid fire or explosion caused by
the igniting of vapors or dust due to the arcing of
the motor brushes:
a. Do not operate this VAC in areas with
explosive vapors (such as lighter fluid,
cleaners, oil-base paints, gasoline or gasahol)
or dust (such as coal, magnesium, grain or gun
powder) in the air.
b. Do not vacuum explosive dust, flammable,
volatile liquids or hot ashes.
c. Do not use VAC without the filter in place.
d. Do not use VAC with a torn filter. Replacefilter
if torn.
e. Do not use VAC as a sprayer for any flammable
volatile liquid.
f. Tie back long hair.
4. Sears Service Center can repair your vac should
the need ever exist. However, if you choose to
service the vac yourself please read and under-
stand MAINTENANCE instructions before
changing brush assembly.
WARNING: Taking apart this VAC can result in
dangerous electrical hazard if any leads (wires)
are pinched against metal surfaces when VAC is
put together again.
5. NOTE: Static Build-up -- A stationary electrical
charge may sometimes build up around your vac
hose and housing. This is common in dry areas
anda slight shock may be gotten much the same
as walking across a carpet and touching a wall
switch. This is onty temporary and doesnot affect
the use of the vac.
Aspecial 2-1/2 inch diameter hose and extension
handle Kit which may reducetheamount of static
build up, Service Part Number 73100, can be
purchased through your Sears Service
Department.
Additional Safety Instructions
1. Plug VAC into 110-120v. grounding type outlet
protected by 15 amp. fuse or circuit breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED
BY A QUALIFIED ELECTRICIAN.
if the outlet you are planning to use for your VAC
is of the two prong type DO NOT REMOVE OR
ALTER THE GROUNDING PRONG IN ANY
WAY. It is recommended that you have a qualified
electrician replace the two-prong outlet with a
grounding type 3-prong.
As an alternative you may use an adapter as
shown being sure to connect the grounding lug
to a known ground.
GROUNDING LUG
/
ADAPTER /-
\/
3-PRONG \ ÷ |/_'j, ! MAKE SURE THIS IS
NOTE: The adapter shown is for use only if you
already have a properly grounded 2-prong
receptacle.
WARNING: IF NOT PROPERLY GROUNDED
this Vac can cause the potenUa! hazard of
electrical shock.
2. Empty drum and clean filter often to keep motor
cool and running at its best.
WARNING: Unplug power cord before cleaning
or changing the filter.
3. Replace both brushes when either is worn to
about 1/4" in length or after about 500 operating
hours.
4. Use filter at all times to avoid damaging motor.
5. Check gasket on lid after emptying drum for
wrinkling or pulling away. Replace if badly worn
or torn.
6. Grasp plug to remove from wall socket, not by
pulling cord.
7. Don't use VAC unless filter is in correct position.
8. Don't oil or grease motor or blower bearings.
These are sealed bearings.
2
g.Make sure filter is dry for both dry vacuuming and
storing.
10. Use only recommended accessories.
11. Note the cautions and warnings that appear on
the motor housing and dust drum:
CAUTION: Keep Filter clean.
WARNING: To avoid eaectric shock do not expose
to rain. Store indoors.
WARNING: For your own safety, read and under-
stand Owner's Manual. Do not pick up flarnrnabie
materials, hot ashes or coals. Do not use around
explosive liquids or vapors.
The operation of any utility vac can result in foreign
objects being b_own into the eyes, which can result
in severe eye damage. Always wear safety goggles
introduction
Your Home N Shop Vac is made for both vacuuming
and blowing. You will find many uses for both; from
blowing sawdust and wood chips off of your
Craftsman power tools to vacuuming excess water
from your basement floor.
\
complying with ANSi Z87.1 (shown on Package)
before commencing operation. Safety Goggles are
available at Sears retail or catalog stores.
CONTENTS
Rules for Safe Operation ..................... 2
Introduction ................................. 3
Unpacking and Checking Contents ........... 3
Assembly .................................... 4
Operation ................................... 5
Maintenance ................................. 6
Optional Accessories ........................ 8
Repair Parts ................................. 9
unpacking and checking contents
Model 113.178200 Home-N-Shop Vac is shipped
complete but does not include the optional
accessory kit. Available accessories can be found
on page 8.
Open carton and remove all accessories laying in
top of carton. Check each item with the Carton
Contents list and notify your Sears Store
immediately if any parts are missing.
CARTON CONTENTS
Key Description Qty
A Hose Assembly (2-1/2" Dia.) .... 1
B Shop Vac Assembly ............. 1
CFoot, Caster .................... 4
D Bar & Stem Assembly ........... 2
E Nut for Machine Screw .......... 1
FScrew, Machine ................ 1
G Nozzle, Rectangular ............ 1
H Screw, Thread Cutting .......... 8
JCaster ......................... 4
C
/
assembly
TOOLS NEEDED
#2 PHILLIPS SCREWDRIVER
PUTTING YOUR HOME-N-SHOP VAC
TOGETHER
flexible locking tabs. With locking tabs in "out"
position, lift lid away from tank.
_DRUM
OUT '
FLEXIBLE LOCKING TAB
'__lj= /_ ! PUSHING
'f'_b. PULLING
| OUT
|FLEXIBLE
LOCKING
TAB
2. Place dust drum from Home-N-Shop Vac upside
down. Put together caster assembly as shown.
A. Connect the two cross bars with machine
screwand nut-- notice the offsgt in cross bars
-- arrange cross bars as shown in sketch so ali
mounting stems are the same height. Snap
mounting stems into bottom of dust drum.
MOUNTING STEMS
\CROSSBARS
NUT
® \
CASTER
CASTER --
I
THREAD CUTTING SCREWS---_ _
B. Slip each caster foot over ends of cross bars
and insert thread cutting screws through
caster, caster foot and into cross bar. Do not
tighten screws until all parts are in place. Press
caster feet against dust drum and tighten
sc rews. _DUST DRUM
4
3. Before replacing the lid check to see if filter wing
nut is tight. It should be tight enough that filter
cannot turn easily. Finger tight only.
4. Replace the lid assembly on the dust drum. Push
down on both handles at once: Make sure that the
locking tabs are snapped in place to prevent the
lid from coming off.
5. Your vac is furnished with a 2-1/2" diameter
swivel hose and rectangular nozzle for maximum
performance.
6. Put one end of your new swivel hose into the
opening for vacuuming and connect the nozzle
furnished with your vac to the other end of the
hose and you are ready to vacuum.
operations
USING YOUR HOME-N-SHOP VAC
1. Wet Pick Up
A. Filter must be in place at all times.
B. Use same filter for wet or dry pick-up. No
changes have to be made to pick up liquids.
C. Your vac is made to pick up water or any other
non-explosive liquid.
D. Your vac will stop picking up water
automatically when ful!. You can tell when the
cut off occurs by listening to the change in
motor sound which is a higher pitch sound
than normal running.
E. Once the filter is wet, do not pick up dirt ordust
because it will clog the filter. When the filter
dries under these conditions you will probably
have trouble cleaning it. Use a dry filter for d ry
vacuuming. Both water and dirt can be picked
up together but the filter should be cleaned
and dried before storing.
F. Any nozzle can be used to pick up water;
however, a squeegee nozzle is available from
your local Sears Store or Catalog Dept. When
the water has dirt mixed with it, the utility
nozzle that came with your vac works well.
2. Draining the Drum
Your Home-N-Shop Vac has a drain for
emptying liquids. Just loosen the wing nut on
the drain and pull the stopper out.
CORD WRAP
/
3, Dry Pick Up _€€'=_===_==_
A. Always use adry filter when picking up d ry _) F_-_---_ "_'__ ON-OFF
materials like sawdust. __---_T-SWITCH
B. If you pick up sawdust or dry material when _==='==__LOWING_=======_====_"J_
the filter is wet it will clog the filter.
C. To aid drying awet filter you may run the vac VACUUIVi ___ _ jOPENiNG
for about 5 minutes before using itto pick up OPENING _-,_2_a___ _,
dry material. _>___
D. Use your vac to pick up many non-explosive
or flammable materials such as sawdust,
woodch ips and shavings, sand, gravel, even
nails.
4. Blowing
To use your vac for blowing just put the hose into
the opening on the top of your vac that says
"Blowing".
5. On-Off-Switch
Your vac is turned ON or OFF by using the switch
easily found on the Motor Cover.
6. Cord Wrap
When finished using your vac, unplug the cord
and wrap it around the Motor Cover.
maintenance
FILTER MAINTENANCE
WARNING -- Unplug power cord before changing
or cleaning filter.
FILTER SHOULD BE CLEANED OFTEN TO
MAINTAIN PEAK PERFORMANCE
1. TO REMOVE -- Remove wing nut and plate on
bottom of filter. Remove filter by lifting off the
wire guide.
2. TO CLEAN --
A. Dry dust applications -- shake or tap filter to
remove dust.
B Wet applications -- if dirt will not come off
with shaking or tapping; then, run water
through filter, Make sure filter is dry before
replacing. Run unit with filter in place to aid
drying.
NOTE: Don't use vac with torn, ripped or badly
worn filter. Small tears may be repaired with tape.
3. TO REPLACE -- Threaded part of wire guide
goes through middle hole in bottom plate of filter,
Make sure filter is setting evenly on lid. Wing nut
holds filter in place. Run wingnut down till it is
finger tight.
WARNING: if you use a wet filter on dry pickup or
store a wet filter, you may damage the filter. Dry
filter before storing.
Replace atom, ripped or badly worn filter right away
to keep dust from getting in the motor,
6
PLATE --
WBNG NUT
ER
_* WING NUT
IPLATE
===llf WIR E GUIDE
_FILTER SEAT
ON LiD
REPLACING BRUSHES
NOTE: Sears Service Center can repair your vac
should the need ever exist. However, if you choose
to service the vac yourself please read and
understand the maintenance instructions before
changing brush assembly.
A. if motor does not run check the plug and cord
and fuse or circuit breaker for faults before
working on the vac.
B. When brushes are worn to about 1/4" orafter500
operating hours, they should be replaced.
C. Your vac motor has two brushes, if either needs
to be replaced then both must be replaced atthat
time.
WARNING -- unplug power cord before working
on motor, blower, or changing brushes.
TO REPLACE BRUSHES ON MOTOR -- Be sure to
replace both brushes at same time.
1. Remove screw holding Dome as shown. Remove
Dome.
2. Remove five screws holding Motor Cover as
shown. Remove Motor Cover. It will be easier if
you replace one brush holder at a time.
(1) SCREW
(4) SCREWS _
_MOTOR COVER
\
I
I
NOTE: To avoid crossing brush wires connect flag
terminal to new brush as soon as it is removed from
old brush.
The brush and plastic holder are connected and are
replaced as a complete unit.
3. Remove Screw, Retainer and Brush Holder
Assembly as shown. Brush Holder Assembly is
thrown away after Flag Connector is removed
from Brush Holder.
4. Connect new brush holder to flag connector. (Be
sure connectors are put back together the same
way they were taken off.) Putting connectors on
wrong will cause damage to the motor. Replace
brush holder, retainer and screw.
5. Put the Motor Cover back on.
6. Put the Dome back on.
NOTE: When new brushes are put in, the motor
may sound differently for a while until the new
brushes are seated.
BRUSH AND
BRUSH HOLDER
FLAG TERMINAL SCREW
Sears Home-N-Shop Vac recommended accessories
7
2-1/2" DIAMETER ACCESSORIES
For large debris, the current 2-1/2" diameter
accessories shown below are available at your
nearest Sears retail or catalog order store.
1. 9-16901 -- Round Brush for dusting.
2. 9-16964 Extension handles for 2-1/2" hose.
Extends work-area range up to 46" more.
3. 9-16902 -- Crevice Tool for cleaning
Hard-to-reach areas.
4. 9-17818-- 2-1/2" diameter Extension Hose and
Connector Kit extends cleaning reach up to 72".
5.9-17817 -- 14" Squeegee Nozzle for wet
pick-up. Complete with built-in, flexible
squeegee blade to wipe clean and pick up water.
suds and other liquids.
.
7°
9-16925 14" Wide Nozzle with brush for large
area pick-up. Gets dust and dirt from bare
floors.
9-16978 -- Car Nozzle idea for cleaning the
inside of your car -- picks up stones and dirt off
carpet: cleans ash tray without having to remove
tray. ACCESSORY SET
9- 16919 -- 6 Piece Accessory Set includes (1)
Round Brush, (2) Two Extension Handles, (3)
Crevice Tool, (6) 14" Wide Nozzle, (5) Squeegee
Nozzle.
The above recommended accessories were current
and available at the time of printing.
Q
1-1/4" DIAMETER ACCESSORIES
The current 1-1/4" diameter accessories shown
below are available at your nearest Sears retail or
catalog order store.
1. 9-17861 Extension handles for 1-1/4" hose.
Extends work area range up to 40" more.
2. 9-17862 -- Round brush for dusting protects
fine furniture, great on stairs and blinds. Soft
bristles pick up dirt from hard-to-clean areas.
convenient angled neck.
3. 9-17866 -- 1-1/4" diameter extension hose
extends cleaning reach up to 72".
4. 9-17826 -- 11 "squeegee nozzle for wet pic k-up.
Complete with built-in, flexible squeegee blade
towipe clean and pick up water, suds and other
liquids.
5. 9-17825 -- 11-3/8" wide nozzle with brush for
large area pick-up. Gets dust and dirt from bare
floors.
6. 9-17863 9" crevice tool cleans hard-to-reach
areas. Remove long-standing dust from behind
radiators, under appliances, beneath
low-sitting objects, behind seats.
7. 9-17868 Car nozzle ideal for cleaning the
inside of your car-- picks up stones and dirt off
carpet: cleans ash tray without having to remove
tray.
ACCESSORY SET
9-17869 -- Six-piece Basic Accessory Set for use
with 1-1/4" hose and handles. Includes (1) two
Extension Handles. (2) Round Brush. (6) Crevice
Tool. (5) Wide-Nozzle Floor Brush and (4) Wet
Nozzle.
The above recommended accessories were current
and available at the time of printing.
repair parts il ¸: _ i
PARTS LiST FOR 16 GALLON HOME-N-SHOP VAC 113.178200
C)-----
I
3
5
/
_ f
J
FIGURE 1 4
MOTOR ASSEMBLY 25996
10
9
678
9 8
Key
No.
1
2
3
4
5
6
7
8
9
10
Part No.
28932
15531
23665
V26003
28891
STD600805
15539
[ STD600803
19552
125916
Description
Frame
Ring, Pressure
Armature Assembly
Brush Assembly
Retainer
*Screw, Pan Cross Type
T 8-32 x 1/2
Bracket, Bearing
*Screw, Pan Cross 8-32 x 7/16
Clip
Field Assembly
*Standard Hardware Item -- May be Purchased Locally
9
PAR_S UST FOR 16 GALLON HOME_N_SHOP VAC 1"03,178200
Figure 2
10
PARTS LiST FOR 16 GALLON HOME'N'SHOP VAC 113.178200
FnGURE 2
Key
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Part No.
STD600803
22209
STD6t0803
73146
STD611005
STD610605
STD551006
17787
22210-01
24473
25996
19002
20432
22188-01
73120
22215
24782
STD510810
22212-01
STD610807
73150
20557-01
73147
73148
!STD541625
!20560
STD541008
21297-01
Description
*Screw, Pan Cross 8-32 x 7/16'
Cover Assembly
*Screw, Pan Cross Type
BT 8 x 3/8
Dome
*Screw, Pan Cross Type
AB 10 x 5/8
*Screw, Pan Cross Type
BT 6 x 1/2
*Washer, .156 x.404 x.033
Washer, Spring
Lever
Bushing, Snap
Motor Assembly
Screw, Pan Cross Type
T 6-32 x 3/4
Switch
Bracket, Switch
Tie, Cable
Gasket
Collector Assembly
Screw, Pan Rec. Hd. 8-32 x 1
Ferrule
*Screw, Pan Cross Type
B #8 x 3/4
Hose Assembly
Nozzle, Rectangular
Filter Assembly
Plate, Filter
*Nut, Wing 1/4-20
Drum Assembly
*Nut, Hex 8-32
Bar and Stem Assembly
t%eoY. PaN No.
29 21171-20
30 13833
31 20605
32 21296-01
33 STD510805
34 27726-01
35 20605
36 22189
37 25969
38 STD541408
39 STD551008
40 28229-01
41 13968
42 28963
43 20866
44 STD541031
45 15534
46 22220
47 22192
48 19693
49 STD375007
50 22364-01
51 STD510807
52
53
54
STD600802
24464
STD610805
73149
Description
Foot, Caster
Caster
Screw, Pan Cross Type
T 10-24 x 1/2
Bar and Stem Assembly
*Screw, Pan Cross 8-32 x 1/2
Guide Assembly
Screw, Pan Cross Type
T 10-24 x 1/2
Float Assembly
Gasket
*Nut, Lock 8-32
*Washer, 13/64 x 1/2 x 3/64
Nozzle
Plug Assembly
Lid Assembly (Includes
Key #37)
Gasket
*Nut, Hex 5/16-18
Washer
Wheel Assembly
Spacer
Cord Assembly
*Connector
Handle
*Screw, Truss Cross
8-32 x 3/4
*Screw, Pan Cross 8-32 x 5/16
Clamp
*Screw, Pan Cross Type
AB 8 x 1/2
Owners Manual
(Not Illustrated)
*Standard Hardware Item -- May be Purchased Locally
11
Sears
SERVICE
MODEL NO.
113.178200
HOW TO ORDER
REPAIR PARTS
HONE-N-SHOP VAC
Now that you have purchased your Home-N-Shop Vac,
should a need ever exist for repair parts or service, simply
contact any Sears Service Center and most Sears, Roebuck
and Co. stores. See how to order repair parts below.
Model and serial number may be found on the Motor Cover
of your Home-N-Shop Vac.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
PART NUMBER PART DESCRIPTION
MODEL NUMBER NAME OF ITEM
113.178200 HOME-N-SHOP VAC
All parts listed may be ordered from any Sears Service
Center and most Sears stores. If the parts you need are not
stocked locally, your order will be electronically
transmitted to a Sears Repair Parts Distribution Center for
handling.
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.
Part No. 73149 Form No. SP4560-4 Printed in U.S.A. 5/83
