Craftsman 113196120 User Manual RADIAL SAW Manuals And Guides L0804093

CRAFTSMAN Saw Radial Manual L0804093 CRAFTSMAN Saw Radial Owner's Manual, CRAFTSMAN Saw Radial installation guides

User Manual: Craftsman 113196120 113196120 CRAFTSMAN RADIAL SAW - Manuals and Guides View the owners manual for your CRAFTSMAN RADIAL SAW #113196120. Home:Tool Parts:Craftsman Parts:Craftsman RADIAL SAW Manual

Open the PDF directly: View PDF .
Page Count: 80

Download
Open PDF In Browser	View PDF

Save This Manual-"
For Future Reference

owner's
manual
MODEL NO.
113.196120
SAW ON LY
or

113.196320
SAW WITH LEGS
or

113.196420
CONTRACTOR'S

SAW

Serial
Number
Model and serial numbers
may be found at the front
of the base.
You should record both
model and serial number in
a safe place for future use.

FOR YOUR
SAFETY:
READALL
INSTRUCTIONS
CAREFULLY

113:196420

__ARS / r.RRFT$M RN
10-INCH RADIAL SAW

• assembly
• operating
• repair parts

J
Sold by SEARS, ROEBUCK AND CO., Chicago,
Part

No. SP5599

IL 60684 U.S.A.
Printed

in U.S.A.

Fable of Contents
Section

Title ................................................................................

Page

Safety ........................................................................................................................

Introduction ............................................................................................................

Assembly ................................................................................................................

Adjustments ............................................................................................................

Alignment ...............................................................................................................

Controls ..................................................................................................................

Electrical Connections ...........................................................................................

Crosscutting ............................................................................................................

Ripping ...................................................................................................................

Cutting Aides .........................................................................................................

Accessories .............................................................................................................

Maintenance ...........................................................................................................

Troubleshooting

.....................................................................................................

Repair Parts ............................................................................................................

FULL ONE YEAR WARRANTY

ON CRAFTSMAN

RADIAL

ARM SAW

If within one year from the date of purchase, this Craftsman Radial Saw fails due
to a defect in material or workmanship, Sears will repair it, free of charge.
WARRANTY
SERVICE IS AVAILABLE BY SIMPLY
NEAREST SEARS SERVICE CENTER/DEPARTMENT
UNITED STATES.
This warranty

applies only while this product

CONTACTING
THE
THROUGHOUT
THE

is used in the United States.

This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
SEARS, ROEBUCK AND CO. D/817 WA
HOFFMAN ESTATES, IL 60195

Safety
This manual has safety information and
instructions to help users eliminate or reduce
the risk of accidents and injuries, including:

1. Severe cuts, and loss of fingers or other
body parts due to contact with the blade.
2. Eye impact injuries, and blindness, from
being hit by a thrown workpiece, workpiece
chips or pieces of blade.
3. Bodily impact injuries, broken bones, and
internal organ damage from being hit by a
thrown work_iece

4. Shock or electrocution

Major Hazards
Three major hazards are associated with
using the radial arm saw for ripping. They
are ouffeed zone hazard, kickback, and
wrong way feed.
This section only briefly explains these hazards. Read the ripping and crosscutting safety sections for more detailed explanations of
these and other hazards.

Ouffeed

Zone Hazard

5. Bums.

_DANGER

Safety Symbol and Signal Words
An exclamation mark inside a triangle is the
safety alert symbol.
It is used to draw attention to safety information in the manual and on the saw. It is
followed by a signal word, DANGER,
WARNING, or CAUTION, which tells the
level of risk:
,_
DANGER: mean_s if the safety information is not followed someone will be seriously

injured or killed.

WARNING: means if the safety informarion is not followed someone could be
seriously injured or killed.
A

CAUTION:

means if the safety infor-

marion is not followed
injured.

someone might be

Read and follow all safety
and instructions.

information

If you reach around the blade to the outfeed
side when ripping, and try to hold down or
pull the woricpiece through to complete a
cut, the rotational force of the blade will pull
your hand back into the blade.
Fingers will be cut off.
Read and follow the information and
instructions under ripping safety.

Safety
Kickback

Hazard

Kickback is the uncontrolled propelling of
the workpiece back toward the user during
ripping.

WARNING

The cause of kickback is the binding or
pinching of the blade in the workpiece.
Several conditions can cause the blade to
bind or pinch.
KICKBACK

II1_

When a workpiece kicks back, it could hit
hard enough to cause internal organ injury,
broken bones, or death.
Read and follow the information
instructions

and

under ripping safety.

Wrong Way Feed Hazard
Wrong way feed is ripping by feeding the
workpiece into the outfeed side of the blade.

,WARNING

The rotational force of the blade can grab
and pull the workpiece.
Before you can let go or pull back, the force
could pull your hand along with the workpiece into the blade. Fingers or hand could
be cut off.

The propelled workpiece could hit a bystander, causing severe impact injury or
death.
Read and follow the information
instructions

under ripping safety.

and

Wrong Way Feed

Safety
Guard Function and Features
The guard is a very important safety feature,
designed to reduce the risk of injury associated with blade contact. Install the guard
correctly. Follow the specific instructions
in the ripping and crosscutting
sections to
set and use the guard correctly for each
type of cuL
Guard Features Include:
1. A non-moveable metal upper
(Upper Guard) which is fastened
motor by the guard clamp screw,
fully covers the upper half of the

Handle/Squeeze
Trigger

portion,
to the
and which
blade.

2. A moveable clear plastic portion,
(Plastic Lower Guard) which partially covers the lower half of the blade. It protects
against contact with the side of the blade
during crosscutting when blade is in its rearmost position and the guard is resting on the
table, so the leading and trailing teeth of the
blade are not exposed. It also protects
against contact with the ouffeed side of the
blade during ripping, and acts as a barrier to
prevem wrong way feed.
3. A squeeze trigger in the saw handle to
raise the clear plastic guard at the start of a
crosscut. Note: This is necessary because
the guard will not automatically raise to
clear the fence.

Pawls/Riving
Knife Knob

Upper Guard

Plastic Lower
Guard

Hold Down
Knob

4. A hold down to be lowered to just clear
the top of the workpiece for ripping. It acts
as a barrier to the infeed side of the blade,
keeps the workpiece from fluttering, and
acts as a sawdust deflector. It is
locked/unlocked

Riving
Knife

by the hold down knob.

5. A riving knife to be lowered to the table
for ripping. It keeps the workpiece kerf
open, thereby reducing blade pinching and
the risk of kickback. It also acts as a barrier
to the hazardous outfeed side and prevents
wrong way feed. It is locked/unlocked by

Pawls

Hold
Down

!
Workpiece

Safety
the pawls/riving knife knob. When lowered
for crosscutting, it acts as a barrier to the
leading edge of the blade.
6. Set of pawls to be lowered to the workpiece surface for ripping. They allow the
workpiece to pass freely from infeed to outfeed side, but help stop the kickback motion
from outfeed to infeed side by grabbing into
the workpiece surface. Pawls must be re-set
each time a different thickness workpiece is

Guard Tab

cut.

7. A guard tab to manually raise the plastic
guard at the start of ripping unusual workpieces whose size/shape do not cause the
guard to raise automatically.

_CAUTION

Hazards Associated with Clear
Portion of Guard
The following safety information
all blades and accessories.

Clear plastic portion of guard can
get caught or jam in fence or table
kerfs. Read and follow the warning
on the guard:

applies to

WARNING

Clear plastic portion of guard will
not provide any protection
during
crosscutting
if blade is pulled over
your hand, or your hand enters
blade path from front or rear of
blade. Fingers or hand can be cut or
cut off.

,_WARNING:
TO AVOID INJURY
SHUT OFF POWER
BEFORE CLEARING A
JAMMED LOWER GUARD

WARNING
Clear plastic guard will increase risk of certain hazards:
•

During rip and bevel cuts, narrow

cut-off
pieces
can be pinched
between guard and blade. Cut-off
pieces can kickback.
• In bevel position blade teeth are
fully exposed. Fingers or hand can
be cut off.

• Cut off pieces can jam between
guard and blade. Turn saw off and
wait for blade to stop before freeing
jammed guard or blade.
• Workpiece
or cut-off pieces can
be violently thrown by blade. Wear
safety goggles. Stand out of workpiece path.

Safety
Safety Instructions
Read and follow all safety instructions.
Personal Safety Instructions
1. Wear safety goggles labeled"ANSI
Z87.1" on the package. It means the goggles
meet impact standards set by the American
National Standards Institute. Regular eyeglasses are not safety goggles.

safety Goggles

2. Wear close fitting clothes, short sleeved
shirts, and non-slip shoes. Tie up long hair.
Do not wear gloves, ties, jewelry, loose
clothing, or long sleeves. These can get
caught in the spinning blade and pull body
parts into the blade.

Dust Mask

3. Wear dust mask to keep from inhaling
fine particles.
4. Wear ear protectors,
use saw daily.

plugs or muffs if you

5. Keep good footing and balance;
over-reach.

do not

Ear Protectors

Work Area Safety Instructions
1. Keep children, pets, and visitors out of
work area; they could be hit by a thrown
workpiece, workpiece chips or pieces of
blade.
2. Turn saw

off, remove yellow key, and

unplug before leaving work area. Do not
leave until blade has stopped spinning.
3. Make work area child-proof: remove yellow key to prevent accidental start-up; store
key out of sight and reach; lock work area.
4. Keep floors clean and free of sawdust,
wax and other slippery materials.
5. Keep work area well lighted and uncluttered.

\
\

6. Use saw only in dry area. Do not use in
wet or damp areas.

Safety
Saw Safety Instructions
1. Use guard, pawls and riving knife according to instructions. Keep them in working
order.

6. Before turning on saw, clear table of all
objects except workpiece to be cut and necessary fixtures, clamps, or feather-boards.

2. Routinely check saw for broken or damaged parts. Repair or replace damaged parts
before using saw. Check new or repaired
parts for alignment, binding, and correct
installation.

7. If blade jams, turn saw off immediately,
remove yellow key, the free blade. Do not
try to free blade with saw on.

3. Unplug saw before doing maintenance,
making adjustments, correcting alignment,
or changing blades.
4. Do not force saw. Use saw, blades and
accessories only as intended.

5. Have yellow key out and saw switched off
before plugging in power cord.

Workplece

Safety

Instructions

1. Cut only wood, woodlike
rials. Do not cut metal.

or plastic mate-

2. Cut only one work_iece at a time.
Stacking or placing workpieces edge to edge
can cause user to lose control of workpiece.

8. Turn saw off if it vibrates too much or
makes an odd sound. Correct any problem
before restarting saw.
9. Do not layout, assemble, or setup work
with saw on, or while blade is spinning.
10. Keep saw table clean.
11. Store items away from saw. Do not
climb on saw or stand on saw table to reach
items because saw can tip over.

Safety
3. Rip only workpieces longer than the
diameter of the blade. Do not rip workpieces
that are shorter than the diameter of the
blade being used.

4. Workpieces that extend beyond the saw
table can shift, twist, rise up from the table,
or fall as they are cut or afterwards. Support
workpiece with table extensions the same
height as the saw table.
5. To prevent tipping, support outer ends of
extensions with sturdy legs or an outrigger.
6. Do not use another person to help support
workpieces or to aid by pushing or pulling
on workpieces, because these actions can
cause kickback. Use table extensions.
7. Use clamps or vice to hold workpiece.
safer than using your hands.

It's

Blade Safety Instructions
1. Use only blades marked for at least 3450
rpm.
2. Use only 10" or smaller diameter blades.
3. Use blades for their recommended
procedures.
4. Keep blade sharp and clean.

cutting

5. Do not overtighten blade nut because
blade collar could warp.
6. Do not turn saw on and off in rapid
sequence because blade can loosen.
7. Blade should stop within 15 seconds after
saw is switched off. If blade takes longer, the
saw needs repair. Contact Sears Service
Center.

Safety
On-Product

Safety Labels

There are several safety labels on the saw.
They alert the user to hazards explained in
the manual and remind the user how to
avoid the hazard.

Note where they are located on the saw.
Read and follow the safety information
and instructions in these labels. Refer to
the manual for detailed explanations and
instructions.

At the outfeed side, to the right of the
guard near the saw handle is this safety
label to alert you to wrong way feed:

INJUh;O0 \
NOTFEED
\
MATERIALINTO\

CUTTINGTOOI.X

On the infeed side of the guard is this safety label to remind you to lower the hold
down to just clear the top of the workpiece for ripping:

&DANGER

On the rear of the yoke, visible from the
infeed side when the saw is in a rip position,
is this safety label to alert you to ouffeed
zone hazard:

Safety
Near the saw handle is this safety label to
alert you to thrown objects and to remind
you to wear safety goggles:

kWARNING

On the clear plastic guard is this OSHA
required label:
TO AVOID INJURY
SHUT OFF POWER
BEFORE
CLEANING A
l=
WARNING:
JAMMED LOWER GUARD

]=J

DANGER
On the bottom surface of the motor, visible
when the cutting tool is horizontal, is this
safety label alerting you to use a guard
when edge molding, and to position the
cutting tool behind the fence:

(see Accessories Section)

Safety

Instructions

On the front of the yoke is this general
safety instruction label:

Assembly
Introduction

In order to get the most enjoyment out of your radial saw it is important that the machine by properly
assembled, adjusted, and aligned. This procedure, although not difficult, takes time; perhaps eight
hours or longer for the inexperienced user. However, after this initial set-up a weekly trine-up can be
completed in approximately ten minutes by checking the alignment and only adjusting those settings
which are incorrect.

Identify Parts
The following

parts are included:

Note: Before beginning assembly, check that
all parts are included. If you are missing any
part, do not assemble the saw. Contact your
Sears Service Center to get the missing part.
Sometimes small parts can get lost in packaging material. Do not throw away any
packaging until saw is put together. Check
packaging for missing parts before contacting Sears. A complete parts list (Repair
Parts) is at the end of the manual. Use the
list to identify the number of the missing
part.
All models

include:

A. Basic Saw Assembly ......... 1
B. Rear Table ..........................
1
C. Spacer Table ......................
D. Fence (wooden) .................
E. Front Table ........................

1
1
1

models

with

__/
G

leg set include:
J

J. Leg .....................................

K. Stiffener,

L.H .....................

L. Stiffener,

R.H .....................

Only

Contractor

M.Lower

Stiffener

model

includes:

..................

* Number varies; bags can contain other
smaller bags. Note: To make assembly easier keep contents of each bag together and
separate from contents of other bags.
12

F. Table Support .................... 2
G. Loose Parts Bag(s) ............ *
H. Bag Containing
Accessory Guard ............... 1
Orllv

Assembly
All models

include:
@

5/16" - 18 x 3/4" long
square head screw (4)

5/16" diam. hex nut (4)

1/4" diam. hex nut (4)

_]lllllllllllllllllllllll
1/4,,-20x
1"long
pan
head screw
(4)
1/4" hex "_

_] lllllillltl*l=l_l*l_lllllll,lJ_
1/4" - 20 x 1-3/4" long
pan head screw (I)

3/16" hex "L'_

arbor wrench (1)

#6 - 32 x 1/2 pan head screw (4)

shaft wrench (1)

_]llllllllllU

#10 - 32 x 7/8" long
pan head self threading screw (2)
rip scale indicator

NNNN

(2)

1/4" - 20 x 1" long
slotted cup point set screw (1)
yellow key (1)

17/64" flat washer (5)

G
G
©

5/16" flat washer (4)

5/16" lockwasher

1/4" lockwasher

tee nut (1)

(4)

!
table clamp assembly
- thumbscrew

(2)

- square nut
- clamp bracket
- cup washer
13

Assembly
crank

Model

113.196320

cap

and 113.196420

Only

1/4" diam.x 5/8" long
trusshead screw (40)
(56 for contractor)

leveling foot (4)

1/4" external tooth lockwasher
(40 for 113.196320)
(56 for 113.196420)
5/16" diam. external
lockwasher (4)

3/8" diam. hex nut

(8)
5/16"diam.

11/32" x 11/16" x 1/16"
washer (8)
hexnut

(4)

1/4" diam. hex nut
(40 for 113.196320)
(56 for 113.196420)

Tools needed for Assembly

5/16" diam. x 5/8" long
hex head screw (4)

and Alignment

7/16" Wrench
@

1/2" Wrench
Wrench

9/16" Wrench

Medium Screwdriver
5/8" Wrench

' 15/16" Wrench
Pliers

3
Small

Hammer

Phillips Screwdriver

Framing Square
Pencil

Assembly
,_, WARNING

For model 113.196420

Plugging
in saw during assembly
could result in electrical shock, or
severe cuts from contact with spinning blade.
Do not plug in saw at any time during assembly.
Plug in saw only when it is to be
used.

From among the loose parts, fred the following hardware:
16 Truss Head Screws
16 Lockwashers,

only

1/4-20 x 5/8

1/4" external

16 Hex Nuts, 1/4 -20

It is important for your safety and to get
accurate cuts that you put the saw together
according to these instructions.

1. Attach the lower leg stifeners to the steel
legs using two (2) screws, lockwasher and
hex nuts on each end. For the short side of
stand, use the inside holes in the stiffeners.
For the long side, use the outside holes.

Follow these steps in order.

2. Tighten all nuts securely.

Assembly

Assembling

Steps

steel legs

Note: Steel Legs are furnished with Models
113.196320 and 113.196420 (Not 113.196120).
From among the loose parts, fred the following Hardware:
40 Truss Head Screws, 1/4-20 x 5/8
40 Lockwashers, 1/4-External
40 Hex Nuts, 1/4-20
8 Hex Nuts, 3/8 - 16
4 Leveling Feet
1. Assemble a right stiffener to a left stiffener using four (4) each 1/4-20 x 5/8 long truss
head screws, lockwashers and hex nuts.
Make two assemblies of the 17-3/4" length
and the 21-1/4" length.

Stiffener
L.H.

Stiffener
R.H.

:!:i°:lo
L.H. Stiffener

[

o oo
oo
o

; :1

_ o_ I oo
_ o_
o o
.8

t___

i--

R.H. Stiffener

2,-lJ4"

..._l
--z

X = Location of Truss Head Screws

2. Attach the stiffener assemblies to the legs
using three (3) screws, lockwashers, and
nuts at each end. Use the holes shown with
o

an "X". "tighten all'nuts securely.
•

¢#

3. Install one 3/8-16 hex nut completely onto
each of the leveling feet. Insert one leveling
foot through hole in bottom of each leg and
install a 3/8-16 hex nut.
4. To level steel legs, loosen nut on inside of
leg and turn nut on outside to raise or lower
feet. Adjust all four levelers if necessary, and
then tighten nuts on inside of leg.
Note: These levelers are not intended for
height adjustment.
15

Assembly
Mounting Saw
1. From among the loose parts, find the fob
lowing hardware:
4
4
8
4

Hex Head Screws, 5/16-18 x 5/8
Lockwasher, 5/16 in. External Type
Washers, 11/32 ID
Hex Jam Nuts, 5/16-18

2. Place saw on legs so that holes in bottom
of saw line up with holes marked X in top of
legs.
3. Install screws, washers and nuts as shown.
If you mount the saw on any other
Craftsman base or flat bench, make sure
Elevation Crank has proper clearance to
rotate. The saw must be bolted down.
Position saw to slope slightly rearward, so
when the carriage is installed it will not roll
forward due to gravity.
Saw Base
Hex Head

Flat Washer

Stiffener
R.H.

Leg

Stiffener

Stiffener
LM.

Leg

. ! .
o_o

O
o

o
0

0
0
o
0
0

0
o

000

o o_oi

_kWARNING
Saw must slant slightly
towards
rear to keep blade carriage
from
rolling forward. Workpiece
or saw
can move unexpectedly
if leg set
rocks. Fingers, hand or arm could
be cut off by blade contact. Adjust
leveling feet before using saw.

Hex Nut

Attach Elevation

Crank.

Install crank on elevation

shaft. Be sure

setscrew is tightened on flat of shaft.

Shipping Block

Elevation Crank
(Turn clockwise
to raise arm)

Elevate arm approximately
Remove
16

3 to 4 inches.

shipping block and discard.

Assembly
Attaching Carriage - Motor to Arm
Remove carriage stop screw, lockwasher and
tag. Read and understand warning tag before
discarding.
_I"_ _..

_Warning

_Loc_sher
.,_..__

Stop Screw

_"-- Hex "L" Wrench
(Supplied)

Lock miter/arm lock before proceeding.
Holding carriage assembly with both hands,
carefully start and slide the carriage onto the
tracks. The assembly must be held parallel
with the ann so that all four bearings slide
smoothly onto the arm, preventing any
excessive swain on bearings and track.

Push toward rear of
saw to lock

Miter/Arm
Lever

,_WARNING
Reinstall
carriage stop screw and
Iockwasher
to prevent carriage from
rolling off arm.
Remove two (2) motor packing studs that
are threaded into bottom of motor.

Install arm cap and arm cap trim

ArmCap

Screw

_h.WARNING
Make
certain
unplugged.

power

cord

1. Insert finger under left end of switch lever
and pull out to the "ON" position.
2. Place arm cap in position and install with
(2) 10-32 x 7/8 self threading screws.
3. Push switch to "OFF" position.

Assembly
Remove

saw blade.

1. Tighten carriage lock knob, located on
right side of arm.
2. Loosen guard clamp screw approximately
4 turns.
3. Use one hand to lift the clear plastic guard
at the front of the saw.

Pull down
to loosen "--

Blade

4. Use the other hand to grasp the rear of the
guard (below the dust elbow).
5. Rotate the entire guard assembly forward
approximately 45 °.
6. Remove the guard assembly.
7. Motor shaft has left hand threads. Hold
shaft wrench and rotate arbor wrench down
(clockwise).
8. Remove shaft nut, outer collar, saw blade,
and inner collar. Set aside and out of the
way.
Attach Table Supports
1. Set out:
- two table supports
- four 5/16" 18 x 3/4" long square head
screws

Table

Table
Support

- four 11/32" x 7/8" x 1/16" flatwashers
- four 5/16" lockwashers
- four 5/16" hex nuts

Support

\
Scl'ew$

2. Attach supports to side frame,
sure to use correct holes in table
and side frame: Use two screws
(insert screws through base and

making
supports
per support
then sup-

port); on end of each screw put a fiat washer,
lockwasher and nut then f'mger tighten so
table supports rest in lowest position.

Here

Lockwasher
Flatwasher

Base

*] Front

Mount rails using
these holes

This concludes the assembly section. Except for installing table boards, fence, and table clamps the
saw should be completely assembled. The next section deals with adjusting your saw to remove all
"looseness" in order to get accurate cuts.
18

Adjustments
Arm Lock Adjusting

Miter/Arm
Lock Lever

Wheel

With the arm at an "unindexed" position and
the miter lock applied, the locking action
should feel tight and secure.
Considerable effort should be required to
move the arm back towards 0 °. Its is always
possible to force the arm because of the
leverage advantage the long ann provides.
However, the arm should resist moving
when a reasonable amount of force is
applied.
To check follow these steps:
1. Pnll miter/arm

lock forward to unlock and

rotate arm to approximately

30 ° left or right.

2. Lock miter/arm lock by pushing handle
toward rear of saw.
3. Apply pressure as shown above.
4. If the arm moves easily:
a. Unlock miter lock.
b. Locate the adjusting

wheel as shown.

c. Turn wheel clockwise to tighten,
counterclockwise
to loosen.
5. Repeat steps 1, 2, 3 above and readjust as
necessary.

Arm Lock
Adjusting Wheel

Adjustments
Yoke Clamp Adjustment
Yoke Lock Handle

To check the yoke clamp adjustment follow
these steps:
1. Pull the yoke lock handle towards the
front of saw to unlock yoke. Pull forward on
the swivel index pin (on the left side of carriage) to disengage index pin.
2. Swivel the motor halfway between the
crosscutting and rip position so the index pin
is not engaged.
3. Lock the yoke lock handle.
4. Grasp the motor with both hands and try
to swivel it back into the crosscut position. It
should not move.
5. If it does move follow these steps:
a. Remove arm cap.

b. Remove carriage stop screw and lockwasher with a 1/4 inch hex-L wrench.

Lock Washer

Arm Cap

c. Grasp the carriage assembly, move it
carefully off the end of radial arm, holding it parallel to the radial arm until all
carriage beatings are free of their tracks.

Screw

d. Rest the motor and carriage assembly
on saw frame.
e. Set yoke lock handle at unlocked position. Tighten nut with 15/16" wrench,
until lock handle locks mid-way between
the two legs of the yoke.
f. Hold the motor and carriage assembly
parallel to radial arm and start the rear
bearings onto the lracks. Continue to hold
the assembly parallel to the tracks until
the forward bearings are on the tracks.
g. Slide the carriage rearward on the radial arm and install the carriage stop screw
and lockwasher.
h. Install arm cap.
i. Repeat steps 1-4. Readjust

if necessary.

Carriage Stop
Screw
Hex "L" Wrench
(1/4-Inch)

15/16" Wrench

Adjustments
Bevel Lock Lever
0

The purpose of the bevel lock lever is to
lock the motor at any angle. To check follow
these steps:
Bevel

1. Unlock the bevel lock lever. Move the,
Pin

bevel index pin to the left and rotate the saw
to approximately 30 °. Lock the bevel lock
lever.

2. Use both hands as shown and try to force
the motor out of position. If the motor
moves, the bevel lock lever needs to be
tightened. On the other hand ff it is extremely hard to lock the bevel lock lever it has
been over-tightened.

Bevel
Lock
Lever

3. Follow these steps to adjust:
a. Remove the socket set screw with hex
wrench as shown.
b. Use the bevel lock lever as a wrench to
tighten or loosen the clamp bolt. Do not
over tighten.
Bevel Lock

c. Repeat steps 1 and 2. Re-adjust if necessary
d. Replace bevel lock lever in the locked
position.

_Se

Lo;k::_her

e. Tighten the set screw.
Note: The clamp bolt has a left handed
thread. Therefore, to increase the clamping
effect, rotate the bevel lock lever- when
used as a wrench -from right to left, or
clockwise when viewed from above. If you
accidentally rotate it the wrong way and disengage the bolt from the matching steel nut,
it will be necessary to remove the Yoke
Handle, and Bevel Scale, in order to reinstall the bolt into the nut.

Lever

1_Screw
1/8" Hex "L" Wrench

Bevel Lock Lever
In LockedPosition

Adjustments
Arm to Column Adjustment
If you can move the end of the radial ann up
and down when the ann is unlocked, adjust
as directed below:

3/8-16 Bolts

a. Remove two (2) screws from rear cover
plate. Tighten evenly top two 3/8-16 bolts
until arm moves fn-mly. There should be
no vertical or horizontal movement in the
arm when miter/arm lock is locked and
unlocked.
b. Bottom two nuts should be snugged
evenly, but not nearly as tight as top two
bolts.
c. Re-Install

Adjusting
Support

318-16 Nuts

Rear Cover Plate.

Column Tube in Column

This adjustment

serves two purposes;

• To remove any looseness
unto tube and column
accurate cuts; and

between the col-

support to insure

• To allow the column tube to raise and
lower smoothly.
Note: The following adjustment is very criti.
caL All future alignment procedures rely on
this adjustment being performed correctly.
All looseness must be removed.
1. Index and lock arm at 0° Miter.
While holding the arm with one hand,
hold fingers of other hand as shown,
between column tube and column support. Apply gentle side-to-side pressure at
end of arm. Any side-to-side or rotational
movement can be felt with finger at arrow
location. If looseness exists, the following
adjustments are required.

J
22

Adjustments
2. Loosen (2) 1/4 - 20 Gib socket cap screws
on the left side at the rear of the column support slightly (1/2 turn).
Hex "L" Wrench

,j_

T"-_ I ] I

3. Elevate, and then lower the Arm:

a. If the column tube binds and elevation
is difficult, loosen two 5/16 - 18 plated
bolts on front side of the column support
until you achieve smooth but firm elevation.

Front

Bright Plated

I-

b. If the column tube moves side-to-side
within the column support, tighten the
two 5/16 - 18 plated bolts until movement
disappears - elevation should be smooth
and firm.

4. Now tighten the (2) 1/4 - 20 Gib socket
cap screws until no noticeable rotational
play exists between Column Tube and
Column Support as shown in step 1.

Loosen

5. Turn the elevation handwheel to raise and
lower the saw. If movement is too difficult
slightly loosen the socket cap screws.

Adjustments
Adjusting

Carriage

Bearings

If the carriage bearings are loose it not only
allows the saw blade to move up, down, and
sideways but also results in inaccurate cuts.
Before following these steps make sure the
tracks (steel rods) and carriage bearings have
been cleaned by wiping them with a clean
cloth.
When properly adjusted, the top and bottom
face of all four bearing grooves should be in
contact with the ann tracks for their entire
length and carriage should roll smoothly
with some resistance.
To test for looseness between bearings and
tracks on radial arm, perform the following
steps.
1. Remove

left-hand carriage cover. (2

screws)

2. Push the carriage to its full rearward
tion.

posi-

3. Grasp front carriage beating as shown and
hold as tight as possible. At the same time
pull carriage forward. If you can stop the
bearing from turning, it requires adjusting.
4. Check rear bearing in the same manner.
5. Adjust as follows:

a. Use two 1/2" wrenches to loosen nut
just enough to permit the eccentric screw
to turn.
b. Rotate the eccentric screw a partial turn
(left or right) as required to take up looseness.

Washer
Eccentric
Screw

Assembly

c. Hold the head of eccentric screw in the
position established in the preceding step
and tighten nut on underside of carriage.
Correct adjustment exists when you cannot keep the beatings from turning.
However, excessive bearing pressure will
cause difficult operation and rapid wear.
d. Install
24

carriage

cover.

Carriage

Carriage
Bearing

Plain
Washer

Lockwasher
Nut

Left Side Carriage Bearings

Adjustments
Positioning

Table Supports/Installing

Front Table/Leveling

Front Table

Note: The goal in adjusting the table supports and leveling the front table is to make sure that the
table is the same distance from the radial arm at all points. This ensures that when the table and
blade are installed the clearance between them will be equal at all points.
Positioning

Table Supports

1. Release bevel lock lever, move bevel
index lever to the left and rotate the motor to
position arbor shaft down. Lock bevel lock.
Unlock
Lock ......._.._

2. Unlock and hold miter/arm lock lever in
index release position as shown. Position
arm against left stop (approximately 50 °
miter). Loosen carriage lock knob and position arbor shaft directly over left hand channel.

Index Release
Position

LMctkerHi:rTle

Note: For safety reasons in accordance with
the UL standard, stops have been provided
to prevent 360 ° rotation of the radial arm.
3. Slide the arbor wrench handle between
end of motor shaft and table support to act as
a feeler gauge. Carefully lower the motor
with elevation crank until the end of shaft is
just touching the arbor wrench. The wrench
should slide back and forth with only slight
resistance. "tighten screw "A".
Screw "A"

Note: Do not change this elevation setting
until both left and right hand table support
channels have been adjusted.
4. Move arm and carriage to screw "B".
Adjust position of table support so that the
arbor wrench just slips between the end of
the motor shaft and the support. Tighten
screw

"B".

5. Move arm and carriage to right hand table
support and level in the same manner as in
step 4.
6. Recheck both support channels to make
sure that tightening screws did not affect the
accuracy of the adjustment.
7. Elevate saw and return motor to horizontal position to provide clearance for installation of front work table.

[

Screw

Table Mounting

"A"

Adjustments
Installing

Front Table

l. Set out:
- front table
- tee nut
- 1/4" U-clip
- 1/4" diam. x 7/8" long cup point set
screw
- four 1/4" diam x 1" long pan head
screws

- 1/4" diam. x 1-3/4" long pan head
screw

- five 17/64" I.D. x 5/8" O.D. fiat
washers
- four 1/4" lock washers
- four 1/4" diam. hex nuts.

2. Identify top and bottom of table: top has
counterbored holes. Place table bottom side
up on solid surface. Hammer tee nut into
leveling hole. (This hole is not cotmter-bored
from the top).

3. Snap U-clip onto front edge of base so
hole lines up with hole just to the left of center notch.

4. Place table, top side up, on saw so center
counterbored hole lines up with hole in Uclip. Note: Table will extend over front edge

ofsawframe.

Adjustments
5. Drop a fiat washer into each counterbored hole.

1/4-20 x 1-3/4"
Pan Head Screw

17/64"
Flat Washer

6. Start 1-3/4" long pan head screw through
center hole and into U-clip, but do not fully

1/4-20 x 1"
Pan Head Screw

_Front

Table

tighten.
7. Start cup point set screw through leveling
hole and into tee nut, but do not fully tighten.

...--- Lockwasher
Hex Nut

8. Put 1" long pan head screw in each of four
remaining holes and through matching holes
in table supports. On end of each screw, put
lock washer then nut and tighten with screwdriver.

Make Front Table Flat
1. Place rear table on its edge, across center
of front table. Check for gap between surfaces.

1/4-20 x 7/8" Cup Point Set
Screw

Rear Table
Board
\

Hold Down

Screw
-

Leveling
Set Screw

I_..--.--"'-_

If there is less than 1/32" gap, tighten cup
point set screw until it touches frame (look
undemeath table), then tighten center (1-3/4"
long) pan head screw.
If there is more than 1/32" gap, close gap
by raising or lowering center of front table:
to raise center, tighten cup point set screw
against frame;
to lower center, tighten center (1-3/4" long)
pan head screw:
2. When gap is closed, make sure cup point
set screw touches frame (look undemeath
table), and center (1-3/4" long) pan head
screw is tightened.

This concludes adjusting your saw where you have removed all "looseness" or slack between the
different parts of the saw. The next section deals with actually aligning the sawblade to get accurate
cuts.

Ali nment
This section applies to all three models covered by this manual.
The saw and blade must be aligned correctly
for two reasons:
1) to prevent binding of the blade and workpiece, which can cause jams, kickbacks, or
thrown worklSieces;
2) to make accurate cuts.

_WARNING
Plugging in saw during alignment
could result in accidental
start-up
and severe cuts from contact with
spinning blade.
Do not plug in saw at anytime during alignment or adjustment.
Plug in saw only when it is to be
used.
Check Framing Square

Alignment and Adjustment Steps
The following alignmentsand adjustments
must be made in order. If you miss an
adjustment, you must go back, make the
missed adjustment, and repeat all steps from
that point on.
These adjustments are like f'me tuning a
piece of equipment. Often, a series of steps
must be repeated more than once in order to
get the adjustment right. There are many
adjustments to make. Because some adjustments may be awkward, you may want to
ask someone to help you.
Before you start, make sure the framing
square is true.
Square

This edge must
be straight
g- ....

/
1

I
I
I

Draw light
I
line on board
i
along this edge "_

Should be no gap or overlap here when
square is flipped over to dotted position.

Blade
Rotation

Crosscut Travel

The goal of this adjustment is to make accurate crosscuts. To do so, the radial ann must
be square to the fence, otherwise, there will
be a slight miter angle in all crosscuts.
Squaring

Shaft Wrench
End of arbor wrench

cross cut travel.

resting on table

1. Index but do not lock ann at 0° miter.
2. Install saw blade as shown. Motor shaft
has left hand threads.
Saw

Note: Do not overtighten arbor nut. Use the
arbor wrench to just "snug" it.

•

O-te,/

B,a e

Arbor

Nut
Collar_

Inner
Motor
Collar

Alignment
Miter/Arm

Lock Lever

3. Lower ann until saw blade just clears the
front table. Lock the yoke lock handle and
bevel lock lever.
4. Place a framing square on the table, as
shown, with one leg of square firmly against
rear edge of front table. Position the blade
and square until the leg of the square just
contacts a tooth of the blade. Mark this
tooth.

5. When the carriage is moved slowly back
and forth on the arm, the marked tooth
should just touch the square at all points. If
marked tooth moves into or away from
square the following adjustments are
required:
a. Loosen (3) 3/8 - 16 set screws in arm
latch at rear of ann.
b. Move the arm in direction to make

3/16" Hex "L" Wrench
(Supplied)

marked tooth follow edge of square when
the saw blade is moved along ann in a
"cross cut" manner.
c. Lock miter/arm

lock.

d. Retighten (3) setscrews in arm latch as
tight as possible and recheck "cross cut"
travel.

Note: This squaring of the cross cut travel
will simultaneously set both of the 45 ° miter
index positions.

6. Set miter indicator on 0° position using
end of blade wrench.

Alignment
Install Table Clamps
1. Insert fence, then spacer table, then rear
table.

Front
Table

Fence

Spacer
Table

Rear
Table

/--

2. Set out two unassembled table clamps:
- two cup washers
- two clamp brackets
- two square nuts
- two thumbscrews
3. Slip square nut into slot at top of clamp
bracket.
4. Insert thumbscrew through rear opening,
and turn clockwise until it comes out other

Square
Nut
Cup
Washer

side about 1/2". Note: Ifyouput screw in
front opening, clamp will not work.

Thumbscrew

5. "tilt clamp bracket forward and snap into
place in opening at rear of table support.
6. Hold cup washer with concave side
against rear table. Turn thumbscrew clockwise until it snaps into washer.
7. Repeat steps for other table clamp.

8. Tighten thumbscrews to clamp table sections in place.

Clamp
Bracket

Alignment
Square Blade to Table for
Crosscutting

Bevel
Indicator

The goal of this adjustment is to make the
blade square to the table so that crosscuts
will be accurate; otherwise all crosscuts will
have a slight bevel angle.
1. Lower blade until it just clears front table.
Lock bevel, miter, rip, and yoke locks.
2. Place a framing square on the table with
the short leg against the saw blade and long
leg parallel to fence. Do not allow the square
to rest against a "set-out" tooth; it must rest
fiat against the blade side.

Rip
Fence

3. If the saw blade is square with the table
top (no visible gap appears between the saw
blade and square) no adjustment is required.
Set bevel indicator to 0° reading. If the
square does not touch the saw blade as
shown (with square leg held firmly against
the table top), perform the following adjustments:

Squarex

Square
(Place parallel
to fence)

It ¢'_')

J
Correct

Wrong

Table

a. Tighten

rip lock knob.

b. Remove
handle
socket head screw

by removing
5/16-18
and lockwasher.

Loosen these

c. Slightly loosen the four socket head
screws with 1/4" Hex "L" Wrench. Rotate
motor while holding square fLmaly against
saw blade and table top.
d. Slightly tighten each of the four screws
and recheck...Now
tighten each screw
fight.

e. Reinstall handle and adjust indicator to
0 ° reading.
f. Loosen

ur screws
5/16-18 Socket

Head Screw
5/16" Lockwasher/_°_

1/4" Hex "L" Wrench >_
(Supplied)

rip lock knob.

Alignment
Square

Blade to Fence

Left Hand
Carriage Cover

The goal in setting the blade square to the
fence is to reduce the risk of kickback when
ripping. This adjustment will also reduce
splintering of the workpiece and burning of
the kerf during ripping and crosscutting.

Rip Fence

1. Lower blade until it just clears table.
2. Unlock rip lock, Pull blade forward to
front of ann. Lock rip lock.
3. Place square so short edge is against fence
and long edge is against flat surface of blade
(not on a tooth), just below blade collar.
4. There should be no gap between blade
and square. Note: Not all blades are perfectly flat. Check different points along blade
surface by making quarter turns and looking
for gap each time. Consider overall fit of
blade. If there is no gap, no adjustment is
needed.
5. If there is a visible gap between the saw
blade and square adjust as follows:
a. Remove left hand carriage cover.

Fence

Square

]

L_tWrong/

Wrong

b. Loosen the yoke lock handle. (on right
side of carriage).
c. Loosen slightly the two hex-head
screws holding yoke index pin.
d. Rotate the yoke assembly until gap
between the saw blade and square is eliminated.

Hex Head Screws

e. Lock yoke lock handle. Retighten the
two hex-head screws.
f. Recheck blade squareness.
g. Install carriage cover.
Left side of Carriage

h. Loosen carriage lock knob and retum
blade to rear of arm.
Note:

This alignment

procedure

taneously

set both yoke

for blade

in and out rip.

indexing

will simulpositions

iotor_'_

Alignment
Make Blade Parallel to Table
The goal of this adjustment
workpiece

from being

This adjustment

1. Lock

ripping

and burning

the

or damaged.

oo::: l

splintering

of the keff

and crosscutting.

arm in straight

2. Pull blade

thrown

will also reduce

of the workpiece
during

is to keep

forward

crosscut

position.

and lock rip lock.

3. Raise blade at least 2" above table.
4. Lock motor at 90 ° bevel (blade horizon-

Correct

tal).
5. Place square so long side is on table under
right side of blade, and short side hangs
down vertically at front of saw.

ilade

6. Lower radial arm until blade surface, not a
tooth, just rests on square.

Square
Table

7. There should be no gap between blade
and square. Note: Not all blades are perfectly flat. Check different points along blade
surface by making quarter turns and looking
for gap each time. Consider overall fit of
blade, ff there is no gap, no adjustment is
needed.
8. If there is a visible gap between saw blade
and square, a bevel heel condition exists and
adjustment is required.

Wrong

r-_

Wrong

a. To correct, unlock bevel lock lever.
Loosen the rear motor mount nut until
you can rotate Cam. Rotate Cam as
shown until gap between saw blade and
square is eliminated.
b. Tighten nut.
c. Tighten bevel lock lever and recheck
blade to square.

d. Reposition motor to crosscut position
with blade at rear of arm.

Alignment
Installing and Adjusting
Indicators.

Rip Scale
Screw #6-32 x 1/2

Note: The rip scales and pointers are
intended to be used for quick settings. For
greater accuracy, take direct measurement
between blade and fence.
1. Pre-assemble indicator and twin nut.
Loosen but do not remove two screws which
attach left hand carriage cover.
2. Tilt carriage cover and install rip indicator
with twin nut on inside of cover. Tighten
carriage cover attaching screws.

Twin Nut

3. Loosen but do not remove rip lock knob
in right hand carriage cover. Install rip indicator. Tighten carriage cover attaching

Yokelndex

Lever
Yoke Lock Handle

screws.

4. With fence in its normal position (next to
front table), loosen yoke lock handle, pull
yoke index lever forward and rotate yoke to
the left to index yoke 90 ° from the cross cut
position. This will locate saw blade between
motor and fence. Lock yoke lock handle.
5. Position carriage until edge of blade,
when spun by hand, just touches front face
of fence. The tip-scale indicator (on the right
hand side of radial arm) should now read

Front
Table

Rear
Table

"0" inches on upper portion of the blade "InRip" scale. If not, loosen screws and shift
the indicator until it is aligned with the "0"
mark, then tighten the screws.
Note: With saw blade and fence in the position shown, the upper portion of blade "InRip" scale is used. lffence is moved to
extreme rear position, the lower portion of
blade "In-Rip" scale would be used.

Table Spacer Board

Rip Scale Indicator

I
%

Rip
Lock Knob

Alignment
6. The blade "Out-Rip"
scale indicator on
left hand side of the radial arm is adjusted in
essentially
the same manner as blade "InRip" indicator,
except position blade with 2
inches between fence and face of saw blade.

The tip-scale
indicator should be positioned
to read 2 inches on upper portion of the
blade "Out-Rip"
scale.
Note: With saw blade and fence in the position shown, the upper portion of the blade
"Out-Rip"
scale is used. If fence is moved to
extreme rear position the lower portion of
blade

"Out-Rip"

scale is used.

2"-Measured

lrom

fence

to nearest blade tooth

7. Loosen the yoke lock handle, pull the
yoke index lever forward and return the
blade to the crosscut position.
Note: Blade is now aligned. It is important
that you periodically
check alignment
and
adjustment
to insure accurate cuts and
improve and safety of cutting procedures.

Install Guard
The guard is a very important safety feature.
It covers a large part of the blade and helps
protect against severe cuts. Always use the
guard.
1. Lock motor at 0° bevel (blade vertical).
2. Use one hand to lift clear plastic guard;
use other hand to grasp rear of guard (below
dust elbow). Position guard so riving knife
faces front of saw.
3. Tilt front of guard down about 45°; place
over blade; rotate guard to level position.
Note: Make sure notch in guard fits onto tab
on nugtor. This wil! prevent movement of
guard about motor Squeeze handle trigger
to make sure it raises clear plastic guard. If
it does not, remove and re-install guard,
making sure that trigger mechanism
engages pull link on guard.
4. Tighten guard clamp screw.

Parallel

Alignment
Align Riving Knife to Blade
The goal of this adjustment is to position the
riving knife directly in line with the blade.
Riving knife alignment is an important safety factor. The riving knife rides in the kerr of
the cut workpiece during ripping to keep the
two sides of the workpiece from pinching on
the blade. Blade pinching is a cause of kickback.

Pawls
Fence

Riving Knife

Correct

1. Lock yoke in in-rip position (blade
towards colum, motor towards front of
arm).
2. Lower arm until blade just clears table.
3. Unlock rip lock while holding up lower
plastic guard, move yoke back until blade
touches fence. Lock rip lock.
4. Loosen pawls/riving knife knob. Lower
riving knife to the table and tighten knob.
The riving knife should rest fiat against
fence.
5. If adjustment

is needed:

Wrong

Pawls/Rl_ng Knife
Knob

i) loosen riving knife bracket screw.
ii) slide riving knife so it rests against
fence.
iii) secure riving knife bracket screw.
6. Raise riving knife and tighten pawlsdriving knife knob.
Riving Knife
Screw

Controls
Bevellndex

Lever

Miter/Arm

Lock Lever

On-Off Switch

Yellow Key

Miter/Arm

Lock

Function

OpemtionlComments

Frees radial arm to move; locks
in any desired position; pre-set
indexed positions at 0°, 45°L,
45°R

Pull lever forward to release
index then swing arm left or

right
Hold in unlocked position
moving arm

while

On-Off Switch

Turns motor on/off

Pull on, push off
Requires yellow key

Yellow Key

Allows saw to be switched on

Insert into on-off switch
Remove after turning saw off

Bevel Index Lever

Indexes the saw blade to 0 °,
45 °, or 90 ° pre-set index positions

Move bevel index lever to the
left while positioning
then release it

the blade,

Controls

Yoke Index
Lever

Table Clamp

Bevel Lock Lever

Elevation Crank

Con_ol

_uncfion

Ope_rafiqn/Comments

Bevel Lock Lever

Frees motor to rotate; locks in
any desired position

t_ll lever to release and push to
lock
Support motor before unlocking
because it can swing down

quickly
Bevel index lever must be unindexed before moving motor
Elevation

Crank

Raises/lowers

radial arm

Turn clockwise to raise, counterclockwise to lower

Table Clamp

Frees table sections to allow
changing fence position

Turn clockwise to tighten, counterclockwise to loosen

Yoke Index Lever

Frees yoke to rotate between rip
and crosscut positions

Pull the spring loaded yoke
pivot latch forward to release
this pin

Controls
Rip Scale &
) Indicator

Rip Lock

e Lock
Handle

Saw

Handle

Bevel

Lock

Lever

tonal

Function

Operation/Comments

Yoke Lock Handle

Locks yoke in rip or crosscut
position

Pull handle forward to release;
push handle reward to tighten
Yoke index lever must be unindexed before rotating yoke

Rip lock

Locks carriage to radial ann for
tipping

Rotate counterclockwise
to
release carriage; turn clockwise
to lock carriage in position
Lock before ripping

Rip Scale & Rip
Indicators

Tells approximate
distance
between blade and fence when

Move blade carriage along arm
to align line on indicator with
desired number on scale

saw is in in-rip
tion

Saw Handle

or out-tip

posi-

Provides grasping surface so
carriage can be moved.
Contains trigger mechanism to
raise clear plastic guard when
making a crosscut

Grasp to move blade carriage
Squeeze trigger to raise clear
plastic guard. Clear guard must
be raised over fence to start
crosscut

Controls
Guard Clamp
Screw
Guard

Pawls/Riving
Knife Knob

Hold Down
Knob
Riving Knife
Bracket

Riving Knife
Pawls

Hold Down

Con_ol

Function

Operation/Comments

Guard Clamp
Screw

Secures guard to motor, frees
guard for removal

Tum counterclockwise to
loosen, clockwise to tighten

Guard

Protects against contact with
upper blade; partially protects
against contact with lower
blade; acts as sawdust deflector

Upper part remains fixed in
level position. Notch in guard
fits securely into matching tab
on motor
Clear guard is moveable: raise
over fence at start of crosscut;
See Saw Handle; most workpieces will automatically raise
clear guard during ripping; See
Guard Tab

Hold Down
Knob

Frees hold down to move up
and down; locks hold down in
place

Turn counterclockwise
to
loosen, clockwise to tighten

Hold Down

During ripping, acts as partial
barrier to infeed side of blade;
keeps infeed side of workpiece
from fluttering; acts as sawdust
deflector

For ripping, lower hold down to
top of workpiece surface, then
raise slightly and lock in place.
For crosscutting lock in fully
raised position

Riving Knife
Bracket

Prevents side to side movement
of riving knife and provides
means for adjusting alignment

Loosen to align riving knife,
then tighten

Controls
Pawls/Riving
Knife Knob

Tab

Pawls

\
Riving Knife

Fu_on

Operation/Comments

Guard Tab

Provides manual way to raise
clear plastic guard during tipping when workpiece fails to
raise it

Push and hold until workpiece
clears guard, then release

Pawls/Riving
Knife Knob

Frees pawls and riving knife to
independently move up and
down

Turn counterclockwise

Pawls

During ripping, slow or stop
kickback by digging into workpiece; when lowered during
crosscutting, provide partial barrier to leading edge of blade

For ripping, set pawl level on
workpiece
surface. For safety

Riving Knife

Reduces kickback by keeping
kerr open; when lowered during
crosscutting, provides partial
barrier to leading edge of blade

loosen,

clockwise

to tighten

reasons set pawls before ripping; See Ripping Set-Up for
details and illustrations
For ripping, lower to table
For safety reasons riving knife
must be in line with blade. See
Alignment:
Blade

Riving

Knife

Electrical Connections
Motor Specifications

_WARNING

The AC motor used on this saw is a capacitor-start, non-reversible type. The models
covered in this manual have the following
specifications:

If not properly grounded, this power
tool could cause electrical shock,
particularly
when used in damp
locations.

Specification:

_WARNING

Model
113.196120

Model
113.196320

Model
113.196420

Rated H_P.

1.5

Max Developed HJ _.

2.5

2.75

3.0

Voltage

120

120/240

Amperes

12/6

13/6.5

Hertz, (cycles)

Phase

single

RPM

3450

clockwise

Yes

Arbor Shaft Rotation
Run Capacitor

If electrical
shock
occurs,
your
reaction to shock could bring hands
into contact with blade.

,_WARNING
To avoid electric
shock
or fire,
immediately
replace worn, cut, or
damaged power cord.
The unit is wired for 120V and has a plug
that looks like this:
3-Prong
Plug

Note: If saw does not start when switched
on, immediately turn saw off and refer to
Troublestugoting. Leaving the switch on will
destroy the motor.

Grounding
Prong
Properly
Grounded
Outlet

Power Supply

_WARNING
Saw is factory wired for 120V operation. Connect
to 120V, 15-AMP
branch circuit and use 15-AMP time
delay fuse or circuit breaker.
Failure to connect in this way could
result in injury from shock or fire.
The saw must be properly grounded. Not all
outlets arc properly grounded. If you are not
sure that your outlet is properly grounded,
have it checked by a qualified electrician.

The power tool is equipped with a 3-conductor cord and grounding type plug listed by
Underwriters'
Laboratories.
The ground
conductor has a green jacket and is attached
to the tool housing at one end and to the
ground prong in the attachment plug at the
other end.

The plug requires a mating 3-conductor
grounded type outlet as shown above. If you
have an outlet that is of the 2-prong type, it
is recommended that you have a qualified
electrician replace it with a properly grounded 3-prong outlet.

Electrical Connections
Grounding

Lug

WARNING
To maintain proper tool grounding,
if outlet you are planning to use for
this power tool is a 2-prong type do
not remove
or alter grounding
prong in any manner.
An adapter is available for connecting the
plug to 2-prong receptacles. The green
grounding lead or grounding lug extending
from the adapter must be connected to a permanent ground such as to a properly grounded outlet box.
Extension

3-Prong

Make Sure This Is

2-Prong

,_WARNING

.eco.taclo

Adapter illustrated
is tor use only if
you
already
have
a properly
grounded
2-prong receptacle.

Cords

The use of any extension cord will cause
some loss of power. Determine the minimum wire size (American Wire Gauge No.
(AWG #)) extension cord per table. Use only
3-wire extension cords with 3-prong grounding type plug and 3-pole receptacles which
accept the tool's plug.

Motor Protection

& Reset Button

The motor protector opens the circuit and
stops the motor when the motor temperature
exceeds a safe level, the motor is overloaded, ora low voltage condition exists.
When the protector activates, immediately
turn saw off, remove yellow key and wait
for motor to cool. Push red re-set button and
listen/feel for click to indicate protector is
re-seL If you do not hear/feel a click, motor
is still too hot. Wait a while longer and
repeal (It may take over one hour for the
motor to cool sufficiently for protector to
reset.)

Wire Sizes Required (AWG #)
Cord
Length

120V

240V

0-25ff
26-50fl
51-100fl

No. 16
No. 14
No. 12

No. 16
No. 16
No. 14

Note: The smaller the gauge number, the
heavier the cord. For circuits farther away
from the electrical circuit box, wire size
must be increased proportionately
to deliver
ample voltage to the motor.

Manual
Re-Set
BuHon
(Red)

Electrical Connections
Dual Voltage Motors
Models 113.196320 and 113.196429 ONLY!

To Change Motor Voltage to 240 A.C.
Under normal home workshop conditions, if
full voltage is supplied to the motor, your
saw will operate efficiently on 120V. If any
of the following conditions exist, it will be
advisable to have a qualified electrician
reconnect the motor for 240V operation:
• heavy duty operation
• either undersized or overloaded branch
circuit serves the saw
• power company cannot correct a low voltage situation.
The following procedure to change motor
voltage should be performed only by a qualified electrician. Note: Whenever changing
the switch position from 120 to 240V, make
certain that all necessary steps (including
proper fusing of the branch circuit) are completed.
1. Unplug

_DANGER
To avoid electric shock, unplug saw
before changing motor voltage.
Pan Head
Screw

Oo : oeF

saw.

2. Remove pan head screw from top of
motor cover. Remove motor cover panel at
blade end of motor.
3. Use small screwdriver

to slide dual volt-

age switch to 240V position./
4. Re-install

motor cover panel.

5. Replace 120V power cord plug with
240V, 15 amp, 3-prong plug.
6. Connect power cord white and black leads
to two "hot" plug blades; connect power
cord grounding wire to plug ground prong.
7. Plug cord into 240V, 15 amp, 3-blade
receptacle. Make sure receptacle is connected to a 240V A.C. power supply through a
240V branch circuit having at least a 15 amp
time delay fuse or circuit breaker. Note: No
adapter is available for this type plug.
44

Dual Voltage
Switch

Crosscuttin
Slraighl

Crosscutting

Bevel
Miter

Defined

Compound

Crosscutting is cutting a workpiece to
length. The workpiece is held firmly against
the fence, and the blade is pulled through the
workpiece to make the cut. Straight, bevel,
miter, and compound cuts can be made.
Rolling Carriage
Crosscutting

WARNING

Satety

The hazards associated with crosscutting
include: exposed blade teeth, rolling carriage, and thrown workpiece. This section
explains these hazards and tells how to avoid
them or reduce the risk of their happening.
Read this section before making any type
of crosscut. Follow these steps every time
you make a crosscut.

When saw is turned on, blade can
suddenly come forward. To reduce
risk of this happening:
",/Keep one hand on saw handle when
turning saw on.
_/Adjust leveling feet to make sure radial
ann slants slightly toward rear.
Thrown Workpiece

Exposed

CAUTION

Blade Teeth

WARNING
During crosscutting,
blade teeth
can be exposed. To reduce risk of
having fingers, hand or arm cut off:
4 Correctly

install and use guard.

_1Lower pawls or riving knife to clear
fence or workpiece, whichever is higher, by 1/4". Lowered pawls or riving
knife act as partial barrier to front of
blade.
_/Keep hands away from blade and out of
blade path. Keep hand holding down
workpiece at least 8" from blade.
_1Blade can come off table edge beyond
30 ° left miter position. Use fight miter
position whenever possible.
_/Do not cut freehand.

You will not be

able to control workpiece.
_/If blade jams, turn off saw, remove yellow key, then free blade.

Workpiece
could be picked up by
spinning
blade and thrown.
You
might be hit by thrown workpiece.
To reduce risk of thrown workpiece:
_/Make sure installed

fence is at least half

as high as the work_iece,
than 3/4".

and never less

Start and finish cut with blade in rearmost position, behind fence.
_/Firmly hold workpiece flat on table and
up against fence. Cut only one workpiece at a time.
_/Pull blade through workpiece only far
enough to complete cut, and never
more than half the diameter of blade.
_/Do not touch or move workpieces

until

blade has stopped spinning.
Use length stop only on end of workpiece which is held down.
Use table extensions

to support work-

pieces that extend beyond table.

Crosscutting
Crosscut

Kerfs

A kerf or shallow cut is needed
and fence to serve as a path for
to ensure that the blade cuts all
through the workpiece. A kerf
each different cutting path.

in the table
the blade and
the way
is needed for

To make an approximately 1/16" deep kerr:

1. Prepare table:
- put fence in font position
- tighten table clamps
2. Prepare blade:
- lock blade in crosscut position
- lock radial arm at desired miter angle
- lock motor at desired bevel angle*
- unlock rip lock and push blade to
rearmost position, behind fence
- lower blade* to just clear table
- lower pawls or riving knife to clear
fence by 1/4".
* raise clearplastic guard before changing
bevel angle and when lowering beveled
blade, otherwise it may jam into table.
3. Grasp saw handle, then turn saw on. Keep
one hand on saw handle through step 6.
4. Slowly lower blade until it touches table,
then lower one more full turn of crank.
5. Squeeze handle trigger to raise clear plastic guard so it will clear fence. Pull blade
through fence and across table as far as it
will go.
6. Push blade to rearmost position, behind
fence, and mm saw off. Keep hand on saw
handle until blade stops spinning.

Crosscutting
Making Crosscuts
Follow these steps to make crosscuts.
1. Prepare table:
- put fence in front position
- tighten table clamps
2. Prepare blade:
- lock blade in crosscut position
- lock radial arm at desired miter angle
- lock motor at desired bevel angle*
- unlock rip lock and push blade to
rearmost position, behind fence
- lower blade into kerr* but not touching keff bottom (blade should move
freely).
* raise clear plastic guard before changing
bevel angle and when lowering beveled
blade, otherwise it may jam into table.
3. Position workpiece against fence, and
lower pawls or riving knife to clear fence or
workpiece, whichever is higher, by 1/4".
4. Grasp saw handle, then turn saw on. Keep
one hand on saw handle through step 7.

5. Hold workpiece down and against fence.
Keep hand at least 8" away from blade.
6. Squeeze handle trigger to raise clear plastic guard so it will clear fence and workpiece. Pull blade through workpiece but only
far enough to complete cut, and never more
than half the diameter of blade.

7. Push blade carriage to rearmost position,
behind fence, and turn saw off. Keep hand
on saw handle until blade stops spinning.

Crosscutting
Repetitive Crosscutting
Repetitive crosscutting is the repeated and
continuous cutting of many pieces of lumber
to the same length. Carriage and length stops
can help make this type of crosscutting more
efficient.

Carriage
Stop

A carriage stop defines the distance needed
to pull the blade through to complete each
cut. This will prevent pulling the blade
through more than the recommended
distance.
Length
Stop

To make a carriage stop use lx2 lumber:.

i) cut two pieces, each 2" long
ii) clamp a piece on each side of radial
arm, so blade carriage stops at distance
needed to complete cut
iii) check that clamps do not interfere
with hand grip on saw handle.
A length stop defines the cut length and
ensures that all pieces will be cut to the same
size. Clamp a piece of lx2 lumber on the
fence to define the cut length. Use a length
stop only on the end of the workpi_ce
which is held down.

Crosscutting

Hints

1. To extend life of table top, buy auxiliary
table cover (see Accessories) or make one
out of 1/4" plywood or fiberboard. Clamp or
nail to original table top, section by section.
If you use nails, nail in the four comers to
make sure blade will not contact nails.

2. Make several fences, so each will have
only a few kerfs (See Cutting Aides). Too
many kerfs will weaken a fence.
3. Keep table clean of chips and sawdust.

4. Use sharp blades, and use the right blade
for each job.

5. When making miter or bevel cuts, use
extra force to hold workpiece down because
it tends to move during these types of cuts.
6. When cutting hard woods, like oak, or
making compound cuts, keep arm holding
saw handle rigid and pull blade through
slowly.
7. To keep cut line accurate, periodically
check blade alignment.
8. Do not cut severely warped or crooked
workpieces.

Ripping
Ripping Defined
Ripping is changing the width of a workpiece by cutting along its length. The workpiece is fed into the blade, which rotates in a
fLxed position, parallel to the fence and a set
distance from the fence. A solid fence (no
kerfs) serves as a guide for the workpiece.
Place the fence in the front position for narrower workpieces, or in the rear position for
wider ones.

Front Fence
Position

L°
In-Rip and Out-Rip

Rear Fence
- OR -

Position

[I_

Positions

In-rip and out-rip refer to blade position.
In-rip: the blade is toward the column, and
the motor is toward the table front. In-rip is
recommended
because this position allows
better visibility of the workpiece and your
hands. Use in-rip when you set the blade 1/2
to 16" from the fence.

Out-rip: the blade is toward the table front,
and the motor is toward the column. Use
out-rip only when you set the blade 12" or
more from the fence.
Infeed and Ouffeed

Outleed
Side

Directions

Infeed and ouffeed refer to sides of the
blade.

In-Rip Position

Infeed: the side of the blade where the guard
hold down is. Always start a rip cut at the
infeed side and push the workpiece
through to the ouffeed side.
Ouffeed: the side of the blade where the
pawls and riving knife are. Never start a rip
cut at the ouffeed side. This is wrong way
feed. Never put hands on the ouffeed side
of the blade when ripping because they
can be pulled back into the spinning
blade.

Outfeed Side

Pawls/Riving
Knife

Out-Rip Position
49

Ripping
Workpiece

Positioning

Always set up so that the wider part of
the workpiece is between the blade and
fence. This gives you greater clearance for
push sticks, and allows better stability for
feeding the workpiece.

Example: To rip 2" off a 10" wide board, set
blade in in-rip position 8'" from rear fence.

Push Sticks and Push Blocks
Use push sticks and push blocks instead of
the hands to push the workpiece through to
complete cuts. They help keep hands away
from the blade. A push block is used with an
auxiliary fence. (see Cutting Aides).
Use a push block and auxiliary fence
when the blade is set 1/2 to 2" from the
fence.

Use a push stick when the blade is set 2" or
more from the fence.
Do not set the blade closer than 1/2" to
the fence. The radial saw is the wrong tool
for such a narrow cut. A band saw would
be more appropriate

Ripping

for this type of cut.

Safety

The hazards associated with ripping include:
ouffeed zone hazard, kickback, and wrong
way feed. This section explains these hazards and tells how to avoid them or reduce
the risk of their happening.
this section

before

of rip cut. Follow

Read

these

you make

a rip cut.

making
steps

any

every

type

time

Ripping
Outfeed Zone Hazard

,_DANGER
Rotational
force of blade can pull
hands and fingers back into blade.
Touching,
holding,
or pulling on
outfeed
side of workpiece
while
blade is still spinning will result in
fingers, hand or arm being cut off.
To reduce risk of outfeed hazard:

DANGER

_J Set pawls and riving knife; they act as
partial barrier to outfeed side.
_J Start and finish cut from infeed side.
_J Keep both hands on infeed side.
Keep hands away from ouffeed side.
_/Push workpiece through to complete
cut. Do not reach around to pull it.
_J If blade jams, turn saw off, remove yellow key, then free blade.
Kickback
Kickback is the uncontrolled propelling
the workpiece back toward the user.

WARNING

Kickback
pinched
Pinching
when:

i WARNING

can happen when blade is
or bound by workpiece.
or binding
can happen

• pawls and riving knife are not used or
not set correctly

KICK B._CK

IIJ_

• riving knife is not aligned with blade
• blade is not parallel to fence
• workpiece
is twisted
rocks on table top
• pressure
piece

or warped

is put on outfeed

• workpiece
is released
pushed past pawls

and

side of workbefore

being

• user touches or tries to pull workpiece
through outfeed side before blade has
stopped spinning,
51

Ripping
To reduce risk of kickback:
_/Set pawls and riving knife according to
ripping set-up procedure. Correctly set
riving knife is more likely to prevent
work_iece from binding or pinching
blade; correctly set pawls are more
likely to grab into workpiece to stop or
slow kickback if one happens.
.4 Check that riving knife is in line with
blade (see Aligtmaent: Riving Knife to
Blade).

Cut only straight workpieces so surface
will lie flat on table and edge will stay
tight against fence. If you must cut an
irregular workpiece, attach a straight
edge (see Cutting Aides).

.4 Push workpiece

through from infeed to

ouifeed side until it is completely
pawls.
.4 Use featherboard

(see Cutting Aides).

"4Keep hands away from outfeed side.
"4If blade jams, turn saw off, remove yellow key, then free blade.
"4When cutting composition materials, or
other materials with one smooth and
one rough side, put rough side up so
pawls will be more likely to grab.

Wrong Way Feed
Wrong way feed is ripping by feeding the
workpiece into the ouffeed side of the blade.

,&WARNING

_WARNING
Rotational
force of blade will pull
workplece through violently if workpiece is fed in same direction
as
blade rotates (wrong
way feed).
Hands and fingers could be pulled
along with workpiece into spinning
blade before you can let go or pull
back. Fingers, hand or arm could be
cut off. Propelled workpiece
could
hit bystander.
To eliminate risk of wrong way feed:
_/Feed workpiece

against blade rotation.

_1Set pawls and riving knife; they act as
partial barrier to ouffeed side.

past

Wrong Way Feed

Ripping
Hold Down Function
The hold down must be set correctly during
ripping to act as barrier against the infeed
side of the blade, to help keep the workpiece
flat on the table, and to deflect worlqaiece
chips. It must be lowered to just clear the
workpiece.
The hold down must be re-set each time a
different thickness workpiece

Set Hold-Down to
workpiece
just
clear

___

is cut.

Follow the Ripping Set-Up Procedure to
correctly set the hold down.

Pawls and Riving Knife Function
The pawls and riving knife must be setcorrectly during ripping to reduce the risk of
kickback, to prevent wrong way feed, and to
act as a barrier to the hazardous outfeed side
of the blade.
Set Pawl level
on workpiece

The riving knife rests on the table. It keeps
the workpiece keff open. This reduces the
chances that the cut workpiece will spring
closed and pinch _ blade. Pinching the
blade is a cause of kickback.
The pawls rest level on the upper surface of
the workpiece. During cutting they allow the
workpiece to pass freely from the infeed to
the outfeed side, but help stop the kickback
motion from outfeed to infeed side by grabbing into the workpiece surface,.

Set Riving Knife
fully down

The pawls must be re-set each time a different thickness workpiece is cut.
Follow the Ripping Set-Up Procedure to
correctly set the pawls and riving knife.

Ripping
Ripping Set-up Procedure

_IL WARNING

Follow these steps before ripping.

If workpiece is pushed along fence
with kerfs, workpiece
could get
caught
on kerf, pinch blade and
cause kickback. Do not use cross-

These steps must be repeated each time a
different thickness workplece is ripped. A
kerr must be made for each different

cutting fence for ripping.

width cuL Also see the special notes for
bevel set-up that follow this section.

1. Prepare table:
- insert solid (no kerfs) fence (Note:
Use auxiliary fence when blade is set
1/2 to 2"from fence (See Cutting
Aides)
- tighten table clamps.
2. Prepare blade:
- lock radial arm at 0 ° miter
- lock blade in in-rip position*
- lower blade to just clear table
- lock blade carriage desired distance
from fence. Note: Make sure wider
part of worlqgiece will be between
blade and fence.
* use out-rip

position

for rips 12" or wider.

In-Rip Set-Up

3. Make kerr:
a) turn saw on
b) lower blade about 1/16" into table
c) turn saw off and remove yellow
key.
4. Place
blade.**
blade

workpiece
Note:

parallel

Workpiece

to and up against
will be between

and table front.

5. Lower hold down** to workpiece, then
raise slightly so it just clears top surface of
workpiece. Lock in place.
6. Lower riving knife to table. Lower pawls
to workpiece surface.** Move workpiece
toward outfeed side until one set of pawls
rests level on workpiece surface. Lock in
place.
** bevel

set-up:

see special

notes, next page
Setting Guard For Rip Cut

Ripping
8. Remove workpiece

from table.

9. Ready push stick or push block.
10. Set up table extension(s) and support
their outer ends. Do not use another person
to support workpieces because this can
cause kickback and it exposes helper to
potential hazards at outfeed side.
Special Notes for Bevel Set-Up

,_CAUTION
Bevel ripping creates unique problems of visibility
and feeding.
Before cutting, check the set-up
using both in-rip and out-rip. Use
the position
that gives the best
combination
of workpiece visibility
and push stick clearance.

_WARNING
Bevel the edge that is not against
the fence.
1. When setting bevel angle, raise radial arm
to allow sufficient clearance for blade and
guard to not jam in table.
2. When blade is beveled manually raise
clear plasdc guard before lowering blade to
table or kerr, otherwise it may jam in the
table.
3. To set hold down, place workpiece directly under guard nose, rather than parallel to
blade.
4. To set pawls, place workpiece directly
under set of pawls closer to table. This set of
pawls will keep contact with workpiece surface.
Making

Rip Cuts

Follow these steps to make in-rip cuts. For
out-rip cuts, reverse hand functions; that is,
put right hand on table and use left hand to
support and push workpiece.

In-ripping

1. Follow ripping set-up procedure.

Ripping
2. Insert yellow key and turn saw on.
3. Stand at infeed side and out of line of
workpiece, in case of kickback
finish cut from infeed side.

Start

and

4. Put workpiece on table, in front of hold
down, and tight against fence. To hold workpiece in position, put left hand on table, at
least 8" in front of hold down, and lightly
press fingers against workpiece. Support
workpiece with table extension or right
hand.

CAUTION
For large workpieces use a featherboard in place of your hand on the
table. It gives better support. (See
cutting aides)
5. With fight hand, push workpiece under
hold down and into blade. Keep left hand
fixed on table, applying slight pressure to
keep workpiece against fence.

Out-ripping

6. Use fight hand to continue to apply feed
pressure to part of work_iece close to fence.
Keep hand at least 8" in front of hold down.
Note: Most worlqgieces will automatically
raise clear plastic guard as they pass from
infeed to ouTfeed side. Unusually tall and
narrow workpieces may not raise clear
guard. When this happens, push guard tab
to raise guard, then release tab when guard
rests on top of workpiece surface.

,_CAUTION
Pushing
guard tab means using
only one hand to control workpiece.
While pushing tab, use extra care to
guide workpiece
and to keep hand
at least 8" in front of hold down.
Release tab as soon as clear guard
rests on workpiece.
7. When end of workpiece gets to table, use
push stick or block, instead of hand, on part
of workpiece between blade and fence to
push until workpiece is completely past
pawls.
8. Turn saw off and wait for blade to stop
spinning before touching workpieee.
56

Guard
Tab

In-ripping

Ripping
Dado Blades, Molding Heads
See Accessories for information on safety,
installation and use of dado blades and
molding heads.

Edging
Edging is the use of a dado blade or molding
head in the horizontal position. It is an
advanced technique that requires a molding
head guard and a special fence. See
Accessories for information on safety, installation and use of dado blades and molding
heads for edging. See Cutting Aides for
information on making the special fence.

Ripping Hints
1. To extend life of table top, buy an auxiliar 7 table cover (see Accessories), or make
one out of 1/4" plywood or fiberboard.
Clamp or nail to original table top, section
by section. If you use nails, nail in the four
comers to make sure blade will not contact
nails.
2. Keep table clean of chips and sawdust.
3. Usesharpblades.
4. Use the right blade for each job.
5. For workpiece with one smooth and one
rough surface, such as paneling or finished
fiberboard, cut with rough surface up so
pawls will be more likely to grab in case of
kickback.
6. To keep cut line accurate, periodically
check blade alignment.

7. If you must cut an irregular workpiece,
attach a straight edge (see Cutting Aides).

Cutting Aides
Molding/Sanding
Instructions for operating the Molding Head
are contained in a booklet furnished with the

Rear Table

Molding

head.

For use of Molding Head Cutter or Drum
Sander with saw arbor vertical, the rear table
requires an opening (next to rear face of
fence) for clearance. Cut this opening as
shown.

-lr

2-1/2"

Note: Spacer table is too narrow for this
opening. Be sure opening is cut in the rear
table.

For top-side rabbeting or molding in the inrip position, relieve the fence by positioning
the cutting tool at the desired location on the
am1, locking the Carriage Lock Knob, and
lowering the cutting tool slowly into the
fence - remove only as much material from
the fence as is necessary.
Note: Initial edge cut will round angled
edges offence.
Note: When using drum sander, vacuum
motor often to prevent sawdust/powder
build-up, because powder interferes with
motor ventilation and can clog starter
switch.

Featherboard
5-1/2

Use a featherboard on the infeed side during
ripping to help keep the workpiece against
the fence.

To make a featherboard, use knot-free 3/4"
lumber 5-1/'2" wide. Miter crosscut lumber
at a 30°angle to 24". Rip to make 5" long
cuts about 1/4" apart.

4-1/2

Cutting Aides
Cutting aides include push sticks, fences,
auxiliary fences, push blocks, featherboards, and straight edges.
Push SUcks

Slightly Less
Than Thickness Of

3/4

Workpiece

To make a push stick, use 3/4" knot-free
lumber, or a standard lx2. Cut to dimensions
shown (inches).

Up To 3/8"

-T--

112

1"5/8__.__

'_'--._

"_"4_o,otc. J-->

15 ._"_

l_.._

Fences
Fences are required for all saw operations.
To make a fence, use 3/4" knot-free l_mber
cut to table length. Do not use particle board
or other composite materials because they
are not strong enough. Note: Installed fence
must be at least half as high as the workpiece, and never less than3/4". The fence
can be as high or higher than the workpiece.

Auxiliary Fence and Push Block for
Ripping
An auxiliary fence must be used when making very narrow rip cuts that don't allow
enough room for a push stick without bringing it too close to the blade. An attxiliary
fence must always be used with a push
block
To make an auxiliary fence, use one piece of
3/8" plywood and two pieces of 3/4" plywood. Cut to dimensions shown (inches).
Glue pieces together, and reinforce with
nails.

2-1/4

3/4 Plywood

This Fac
& This Edge

MaUrS:llB
_

1
"__.,-_,_.

..,_,.

LengtlaDleh
__

•

3/8 Plywood
These Edges Must
Be Parallel
3/4 Plywood

To make a push block, use one piece of 3/4"
plywood and one piece of 3/8" plywood. Cut
to dimensions shown (inches). Glue pieces
together and reinforce with nails.
Lay the push block on top of the auxiliary
fence to make sure their widths match exact-

1-1/4 x
1-1/4

3/8 Plywood

ly, and are each 4-3/4".

3/8
2-1/2
3/8"

Cutting Aides
Clamp the featherboard to the front table, so
that the angled edge of the featherboard is
against the workpiece on the infeed side of
the blade. Do not clamp the featherboard
against the cut off part (out-feed side) of
the workpiece. If clamped to the outfeed
side, the featherboard can squeeze the
kerf dosed, put binding pressure on the
blade, and cause kickback.

Straight

Edge for Irregular Workplece

_WARNING
If you try to rip an irregular workpiece, it could bind blade and cause
kickback.
If the workpiece you want to rip does not
have a straight edge, attach a straight-edged
board to the workpiece:
a) place irregular side of workpiece
against fence
b) put straight-edged board on top of
workpiece and against fence
c) tack straight edged board to work
piece.
Note: Straight-edged board must not extend
beyond leading end of workpiece and
should cover workpiece width only enough
to pass between blade and fence.

Note: Usefence at least as high as combined heights of workpiece and straightedged board.

Accessories
Accessories Safety

Information

1. Use only accessories listed in this section.
Use of any other accessory or attachment
might increase the risk of injury to you or
others.

1. Put inside loose collar on arbor shaft first,
then install dado. Tighten blade nut directly
against outside surface of dado.

2. Read and follow instructions that come
with accessory.
3. Do not install accessories on both ends of
arbor shaft at same time.

for Dado

2. Saw arbor is designed for dado up to
13/16" wide. Use of wider dado could cause
dado and blade nut to spin off. To make larger than 13/16" wide cut, take several passes
with dado.

4. Do not use twist drill bits longer than 7"
because they can bend and break.

3. To avoid excessive load on motor when
making a 13/16" wide cut, limit depth of cut
to 1/8" in one pass.

5. Use a spade type driU 1" or smaUer in
diameter for drilling only wood or plastic.

Information for Edging
Edging is the use of a dado or molding head
in the horizontal position. Edging requires
the use of a molding head guard (see
Accessories Lis0

6. Do not use reduced shank drills.
7. Remove blade wrenches
saw

before turning

on.

_k DANGER
Grinding wheels, abrasive or cut off
wheels, or wire wheels can break
explosively
and throw pieces. You
can be blinded
or receive
a life
threatening
puncture
wound.
not use grind wheels, abrasive
cut off wheels, or wire wheels.

Do
or

,_WARNING
When
using
accessory
shaft,
exposed
arbor shaft can pull In
clothing,
hair or jewelry
as it
rotates. Broken bones and severe
cuts could occur.
Follow personal safety Instructions.
Locate arbor shaft under radial arm:
lock blade carriage in out-rip position, then bevel motor to -90 °.

1. Use molding head guard for edging with
molding head and dado blade. Follow
instructions that come with guard. DO not
edge with a blade.
,_

DANGER

Edging without a guard can bring
hands and fingers too close to
blade. Hands, lingers and arm could
be cut off. Buy, install, and follow
instructions
for molding
head
guard.

_kWARNING
Blade cannot be guarded in horizontal position. Edge with guarded
molding head or dado. Do not edge
with blade.
2. Whenever possible, edge with arm locked
at indexed 0 ° miter, so blade carriage is
more likely to lock firmly.
3. Before edging, with saw unplugged and
yellow key out, turn cutting tool by hand to
make sure it does not strike guard or any
other part of saw.

Accessories
Accessories

for this Saw

These accessories are designed to fit this
saw. Read and follow instructions that come
with accessory.
Item ..........................................

Catalog No.

Auxiliary Table Cover ................................... see catalog
Blades (10" with 5/8" hole) ........................... s_g catalog
Dado Blades
Adjustable Dado
7"-24 tooth carbide ................................... see catalog
7"-32 tooth carbide ................................... see catalog
7"-16 tooth carbide ................................... see catalog
8"-48 tooth carbide ................................... see catalog
Satin Cut Dado

7"....................................................
seecatalog
8". .............................................................. see catalog
8" carbide .................................................. see catalog
Standard Cut Dado
8". .............................................................. see catalog
Drill Chuck & Key ........................................ see catalog
Dust Collector .................................................... 9-29963
Extension Table ............................................ .see catalog
Leg Set Caster ................................. 9-22221 or 9-22222
Molding Heads
7" bits not included ................................. .see catalog

7"-27 piece set ..........................................
see catalog
7"-15 piece set .......................................... see catalog
Sanding Wheel -10". ..................................... see catalog
Sanding Drum .................................................... 9-25246
Taper Jig ........................................................ see catalog
Guards
Molding Head Guard -8". ........................ see catalog
Acr.._sory Lower Guard ............................... 9-29010
(supplied with saw)
Books
Power Tool Know How Handbook .............9-29117

Maintenance
General

Information

When new, the saw requires no lubrication.
The saw has been partially aligned and all
bearings are lubricated and sealed for life. In
time, in order to keep the saw in good working order, it will be necessary to dean, lubricate and m-align.

Oil Here

_WARNING
TO avoid shock, burns, or lacerations from accidental
start up of
saw, turn power switch
off and
unplug saw before doing maintenance or servicing saw.

Cam

Surface

Bevel Index Pin

Cleaning
Periodically remove any heavy build-up of
sawdust that may accumulate on the saw.
The absorbing tendency of sawdust will
draw lubricants away from the areas where
they are needed. Wipe the carriage bearings
and track surfaces with a dry or lightly oiled
cloth.
To avoid motor damage due to sawdust
build-up, which interferes with normal
motor ventilation, vacuum the motor often.
Lubrication
Do not lubricate motor bearings, carriage
bearings, or the area between the miter lock
and the column tube. Motor and carriage
bearings are sealed and do not need added
lubrication.

Oil Here

Cam
Surface

Swivel Index Pin

Apply a few drops of oil to top of pin and
allow to flow down sides of pin. Move pin
up and down in its housing to work the oil
over side of pin.

Areas that should be lubricated periodically
are the bevel index pin, swivel index pin,
and column tube.
You can lubricate other points if necessary,
but only when sticking or binding occurs.
Use a small amount of SAE No. 10W30
automotive engine oil. Excess oil attracts airborn dust and sawdust.
63

Maintenance
Replacing

Pawls

Make sure the teeth of the pawls are always
sharp. If they become dull the pawls must be
replaced:
1. Use 7/16" wrench to remove
Remove old pawls.

hex nut.

2. Install new pawls. Place spacers exactly
as shown.
3. Re-install

hex nut.

Blade Changing
To change the saw blade:
1. Turn switch off, remove yellow key, and
unplug saw.
2. Remove guard.
3. Use both blade wrenches in scissor action
to loosen blade nut. Note: Arbor shaft has
left-hand threads. Turn nut clockwise to
loosen.
4. Remove nut, blade collar, and blade.
Install new blade, making sure that arrow is
on outside and points clockwise.
5. Re-instaU blade collar and nut. Note: Do
not overtighten nut because this can cause
blade collar to warp and blade to wobble
during cutting.
6. Re-install

guard.

Troubleshooting
HAVE YOU FOLLOWED ALL STEPS OF THE
ALIGNMENT PROCEDURE? IF YOU HAVE
NOT FOLLOWED THEM IN THEIR PROPER
SEQUENCE, YOU CANNOT EXPECT ACCURATE CUTTING RESULTS.

This Edge of Board
Against Fence For All Cuts

In addition to the proper alignment of your
saw, you must also become familiar with the
following practices in order to expect the
best results.
1. Edge of workpiece which is placed
against fence must be as straight as the long
side of your framing square.
2. Workpiece must be as flat as the front
table board on your saw.
3. There must be no sawdust or other wood
chips between the fence and the front table
board.
4. There must be no sawdust or other wood
chips underneath workpiece or between
workpiece and fence.
5. Workpiece must be hem tightly against
fence and down against the table...this is
especially important when making angle
cuts because the work_iece has a tendency
tomove.

Fence

I ,
Turn Workplece Over End For End...Keep Same Edge
Against Fence When Making Successive Cuts.

%.%.

7 .\

Pencil Line For
Gauging Required Length

6. Always use the correct sawblade for the
job...Always
keep it sharp.
7. When making a four sided frame:
a. The two side pieces must be exactly the
same length.
b. The top and bottom pieces must be
exactly the same length.
c. Always place the same edge of the
workpiece against, the fence...tum
the
workpiece end for end for the successive cuts and mark a pencil line on the
table for gauging the required length.
Deviation from any of the above practices
will have an effect on the accuracy of the
cuts that you make.
65

Troubleshooting
Motor Problem

Possible Cause(s)

What to Do

Motor ove_hemsor stalls

Ovecloadedpower

Reduce line load by removing
other fights, appliances

Feedingrate too fag

Slow down rate of feed

ImlxoPcr motorcooling

Vacuum sawdust from motor to
allow normal air circulation

Saw blade has heel

Check alignment

Saw blade is dull

Sharpen blade

Motor Overloaded

Slow down rate of feed

Need 15 amp circuit

Call your electrician

Need 15 amp slow-blow fuse

Install correct fuses

Low voltage

Check voltage. Normal loads can
be safely handled at 10% above or
below nameplate voltage; heavy
loads need same voltage at motor
terminal as on nameplate

Incorrect gauge extension cord

Refer to table in Electrical
Connections

Overloaded power line

Reduce line load by removing
other lights, appliances

Undersize wires or circuit too long

Increase wire size or shorten
length of wiring

Protector circuit open

Push re-set button; listen and feel
for click

Low voltage

Check power line for correct voltage

Sawdust build-up

Vacuum motor

Bent or bound-up arb_ shaft

Check that shaft turns freely by
hand; if it doesn't, contact Sears

Internal damage

Take saw to Sears for service

While motor is running, fuses
blow

Motor starts slowly of fails to
come to full power

Motor will not run

Fuses blow when motor is turned
on

Troubleshooting
Cutting

Problem

Possible

Cause(s)

What to Do

Looselocks

Chock miter, rip, bevel, and swivel
locks. See Adjustments section

Saw blade out of alignment

Check alignment

Sawdust between workpiece and
fence

Keep front table clean

Fence not straight

Replace fence

Swivel lock loose or not locked

Adjust swivel lock for wear

Crosscut travel not square with
fence

Square blade crosscut travel

Carriage assembly loose on ann

Adjust carriage bearings, then
realign saw

Arm not indexing properly

Adjust miter lock for wear

_ne.ss
between column tube
and column support

Adjust column support

Depth of crosscut varies from one
side of workpiece to other

Table not parallel with radial arm

Adjust table supports

Saw cuts at slight bevel

Blade not square to table

Square blade to table for c,os_utling and tipping

Table not parallel to radial arm

Adjust table supports

Bevel lock loose

Adjust bevel lock

Work table not flat

Adjust or replace table

Carriage bearings loose

Adjust carriage bearings, then
realign saw

Blade not square to fence

Square blade to fence

Using improper blade for desired
finish cut

Use proper smooth-cutting blade

Blade dull

Sharpen or replace blade

User pulls blade through workpiece too fast

Pull blade slowly and steadily
through workpiece

Inaccurate cut

Crosscuts not accurate at indexed

miterpositions

Workpieee kerr rough with tooth
marks from blade

Blade tends to advance through
workpieee too fast during crosscutting

Troubleshooting
Cutting

Problem

Cause(s)

What to Do

Workpiece str_es riving knife during ripping

Riving knife notin line with blade

Alignrivingknifeto blade

Workpiece binds, smokes, and
motor slows or stops when ripping

Saw blade out of alignment

Re-align

Warpedworkpiece

Do not cut severely warped pieces

Feed rote too fast

Slow feed rate

Carriage assembly loose

Adjust carriage bearings, then
realign saw

Fence not straight

l_place fence

Dull or incorrect blade

Sharpen or replace blade

Saw blade out of alignment

Re-align

May occur as normal resdt of
applying feed pressure

Use fea_d

Saw Problem

Possible Cause(s)

What to Do

Radial arm moves when locked in
a non-indexed miter position

Miler not locked firmly

Adjust miter lock for wear

Motor moves when bevel lock is
locked

Bevel not locked firmly

Adjust bevel lock for wear

Yoke moves when rip lock is
locked

Rip lock not locked firmly

Adjust rip lock for wear

Blade carriage does not travel
smoothly on ann

Dirty track

Clean and lubricate mack

Carriage bearings set too fight

Adjust carriage bearings, then realign saw

Rip lock rubbing track

Loosen Rip Lock

Worn steel track

Replace track

Bad carriage bearing

Replace carriage bearing

Blade nut loose

Tighten blade nut

Intea-nal damage

Take saw back to Sears for service

Board pulls away from fence during ripping

Blade does not stop spinning within 15 seconds after saw is turned
off

Possible

on infeed side

Notes

,,,,q
o

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.19_20
& 113.19_20

(I)
"ID
II

"!3
e,,,i,

40
39

RGURE 1

24 25 26 27

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420
Always order by Part Number - Not by Key Number

FIGURE 1
Key
No

Part
No.

1
2
3

63518
75090
60339

4
5
6
7

6O353
815649
63669
STD601105

63670
821361
63686
805494
436594

9
11
12
13
14
15
16
17
18
19

STD551131
9421620

20
21

821473-3
60337

22
23
24

STD512520
821367

STD551010
63884
63885
STD541110

De_xlptlon

Cord, with Plug
Cover, Rear Arm
Screw, Hex Hd Locking, 3/8-16
x 2-1/8 High Strength
Washer, .380 x 47/64 x 1/8
Bearing, Arm
Scale, Miter
* Screw, Pan Rec. Hd
10-32 x 3/8
Indicator, Miter
Trim Arm
Pad, Ann Tnm
NUt, Square 8/8-16
* Screw, Pan Rec. Hd 10-32 x
1-1/2
* Washer, 13/64 x 7/16 x 1/16
Knob, L.H. Lever Arm
Knob, R.H. Lever Arm
* Nut, Hex 10/32
Arm Assembly, See Fig. 5
* Lockwasher, 5/16
Screw, Soc. Hd Cap 5/16-18
x 1/2
Cap, Arm
Screw, Type "-I-"Pan Hd
10/32 x 7/8
Yoke Assembly, See Fig. 2
* Screw, Pan Hd 1/4-20 x 1-3/4
Table, Rear

Key
No

Part
No.

Description

25
26
27
28
29
30
31
32

821368
63432
821366
102711
STD551012
STD512510
37384
37530

Table, Spacer
Fence, Rip
Table, Front
Screw, Set SL. Cup 1/4-20 x 1
* Washer, 17/64 x 5/8 x 1/32
* Screw, Pan Hd 1/4-20 x 1
Nut, Tee
Nut, "U" Clip

34
35
36
37
38
39
40
41
42
43
44
45

STD551125
STD541025
818161
818166
120399
818162
STD541437
63467
60342
63881
9420417

46
47
48
49
-

63683
63682
3540
SP5599

* Lockwasher, 1/4
Nut, Hex 1/4-20
Shoe, Table Clamp
Bracket, Clamp
Nut, Square 5/16 - 18
Screw, Clamp
Base Assembly, See Fig. 3
* Nut, Lock 3/8-16
Cap, Flag Terminal
Bolt, Sq. Hd 3/8-16 x 2-1t4
Clamp, Cord
Screw, Type 'T' Hex Washer
Hd 1/4-20 x 5/8
Guard Assembly, See Fig. 4
Wrench, Hex "L" 3/16
Wrench, Hex "L" 1/4
Wrench
Owners Manual (Not Illustrated)

mll

"13
* Standard Hardware Item- May Be Purchased Locally.

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420
20

20
mll

"10
37

28 29

• Any attempt to repair this motor may create a HAZARD unless repair
Is done by a qualified service technician. Repair service Is available
at your nearest Sears Store.
FIGURE

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420
FIGURE

Key
No

Part
No.
STD601105

2
3
4
5
6
7
8
9
10
11
12
13
14

63661
63786
S1D51 O605
120399
63657
63893
63658
63656
STD551 031
STD551231
STD523107
63778
63782

15
16
17
18
19
20

63777
STD541462
STD551052
30567
30530
60336

21
22
23
24
25
26
27
28
29
30
31
32
33
34

63779
63528
30521
63659
63660
63641
STD541231
30495
62498
9-32668
STD541411
STD551037
63652
63651

Description
* Screw, Type "1" Pan Rec. Hd
10-32 x 1/2
Cover, LH. Carriage
Indicator, Rip
* Screw, Pan Rec. Hd 6-32 x 1/2
Nut, Square 5/16-18
Housing, Index Pin
Pin Assembly, Index
Spring, Index
Bracket, Spring
* Washer, 21/64 x 3/4 x 1/16
* Lockwasher,5/16, Ext. Tooth
* Screw, Hex Hd 5/16-18 x 3/4
Screw, Eccentric
Washer Assembly, Carriage
Bearing
Bearing, Carriage
* Nut, Lock 5/8-11
* Washer, .630 x 1.125 x .093
Bumper
Nut, Speed
Bolt, Hex Hd 5/16-18 x 1-1/2
High Strength
Bearing, Sleeve
Shoe, Rip Lock
Spdng, Swivel Latch
Cover, R.H. Carriage
Knob, Carriage Lock
Carriage
* Nut Hex Jam 5/16-18
Nut, Shaft
Collar
1 Blade, Saw
* Nut, Lock 3/8-16
* Washer, .380 x 47164 x 1/16
Cam, Motor
Stud, Motor

* Standard Hardware Item - May Be Purchased Locally.
1 Stock item - May be secured through the hardware
departments of most Sears Retail Stores or Catalog Order

YOKE ASSEMBLY

Key
No

Part
No.

35
36
37
38
39
40
41
42
43
44

63469
63642
63648
63643
63644
6O333
63645
30582
63620
60337

STD600803

46
47
48
49
50
51
52

63662
821354
821342
9421628
STD551131
60288
9421627

53
54
55

63650
63649
60335

56
57
58

63647
STD551210
806214

59
60
61

STD523120
63646
821506
821545

62
63

30613
STD600805

Description
Bushing, Rubber
Yoke
Knob, Bevel Index
Stud, Yoke Clamp
Handle, Yoke Lock
Nut, Square L.H. 5/16-18
Pin, Index
Cap, Shaft
Trim, Yoke
* Screw, Type "1-"Pan Re<:.Hd
10-32 x 7/8
* Screw, Type "-r" Pan Rec. Hd
8/32 x 5/16
Indicator, Bevel
Trigger
Handle, Yoke
Screw, Soc. Cap 5/16-18 x 2
* Lockwasher, 5/16
Screw, Set 1/4 - 20 x 3/8
Screw, SCc, Cap
5/16-18 x 1-5/8
Plate, Retainer
Ring, Index
Screw, Hex Hd LH.
5/16-18x2
Lever, Bevel Lock
* ockwasher, Ext. Tooth No. 10
Screw, Hex SCc. Button Hd
Cap 10-32 x 5/8
* Screw, Hex Hd 5/16-18 x 2
Cap, Yoke
• Motor (Model 113.196420)
Motor (Models 113.196120,
113.196320)
Clamp, Cord
Screw, Pan
TY 'q" 8-32 x 1/2

• Any attempt to repair this motor may create a HAZARD unless
repair is done by a qualified service technician. Repair service is
available at your nearest Sears Store.

(1)

"O
Ill

""t

..,.j
j_.

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420

(I)

"ID
m
I_11

"R
26
18

28
,27

15 144

33
34

9
47_@\\

\
_

28 46 45
44
43

FIGURE 3

35 36

PARTS UST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420

Always order by Part Number- Not by Key Number
mll

"10
5
"1
pl,

35
8
10

11
18
32

19
17

13
15

21
3029

RGURE 4

PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420
Alwaysorder by Part Number. Not by Key Number
FIGURE 4 - GUARD

Key
No
1
2
3
4

Part
No,
821217
821313
STD551012
815865
STD601105

6
7
8
9

802392-47
808447-6
820529
STD551031

10
11
12
13

820521
820515
STD541425
STD551025

14
15
16
17
18

815815
820517
STD512510
820512
820219-2

Description
Screw, Guard Clamp
Link, Pull
* Washer, 17/64 x 5/8 x 1/16
Screw, Hex Washer Hd Type
'_r" 1/4 - 20 x 1/2
* Screw, Pan Hd Type
"-l-r" 10-32 x 5
Spacer #10 x. 125
Washer, Spring
Knob, 5/16-18
* Washer
21/64 x 5/8 x 1/16
Spacer
Knife, Riving
* Nut, Lock 1/4-20
* Washer
17/64 x 5/8 x 1/16
Pawl, AKB
Bushing
* Screw, Pan Hal. 1/4-20 x 1
Holder, AKB
Screw, Pan Hd Type "T-F"
1/4- 20x 1/2

Key
No

Part
No,

19
20
21
22
23
24
25
26

820523
820526
820519
STD551225
820530
808822-1
805641-1
STD533107

809019-4

28
29

820532
!821449

30
31
32
33
34
35

821310
821311
821312
821314
63258
60413

Description
Clamp, Pawl
Retainer
Nut, Slotted 1/4 - 20
• Lockwasher 1/4
Support, Knife
Nut, Push 1/4
Ring, Retaining
* Bolt, R.H. Short Neck
5/16 - 18 x 5/8
Bolt, Rd Hd Short Neck
5/16 - 18 x 1-3/4
Boif
Nut, Square 5/16 - 18 Double
Lead
Guard, Lower
Unk
Guard
Hold Down
Elbow, Dust
Nut, Push 5/16

m
* Standard Hardware Item - May Be Purchased Locally.

Repair Parts
PARTS LIST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120, 113.196320 & 113.196420

_- IF THIS PART IS REMOVED,
DISCARD AND REPLACE
WITH A NEW PUSH NUT.

FIGURE
Key
No

Part
No.

5 - ARM ASSEMBLY

Description

Key
No

Part
No.

Descdption

Iiiiiiiiiiii

1
2
3
4
5

63626
63629
63631
63628
9420417

6
7
8

63883
63632
63630
63633
60240
STD551031
63872
STD551012
60208
63638

11
12
13
14
15

*
*

Housing, Pin
Pin, Arm Index
Pawl, Arm Lock
Spring, Tension
Screw, Type "T" Hex Washer
Hd 1/4-20 x 5/8
Guide
Rod, Index
Spring, Arm Lock
Rod, Arm Lock
Nut, Push 3/8
Washer, 21/64 x 1 x 1/8
Lever, Arm Lock
Washer, 17/64 x 5/8 x 1/32
Nut, Push 1/4
Pin, Lever

16
17
18
19

63637
63636
63773
STD601103

20
21
22

STD551210
63639
448337

23
24

9-22255
STD600805

63896

26
27

63878
60440

Pin
Pin, Clevis
Insulation
* Screw, Type "1" Pan Hd
10-32 x 3/8
* LocloNasher, Ext. Tooth N10
Track
screw, Type "T" Rd. Hd
10-32 x 5/8
1"Key
* screw, Type "3" Pan Hd
8-32 x 1/2
Switch, Locking
(Includes Key No. 23)
Arm, Radial
Clamp, Cord

* Standard Hardware Item may be Purchased Locally.
, If this part is removed, discard and replace with a new
Push Nut.

PARTS UST FOR CRAFTSMAN 10" RADIAL SAW
MODEL NUMBERS 113.196120; 113.196320 & 113.196420
Always order by Part Number- Not by Key Number

FIGURE-

Key
No

Part
No.

1
2
3
4
5
6
7
8

STD503705
63623
60330
63611
63610
STD572510
821346
9416187

9
10
11
12
13
14
15
16
17

STD523110
60078
STD541037
STD551137
6O340
STD523712
186648
817398-1
60367

60336

19
20
21

63609
821348
635OO

63614

Description

* Screw, Soc. Set 3/8-16 x 1/2
Latch, Arm
Ring, Retaining 3"
Tube
Gib, Column Tube
* Pin, Roll 1/4 x 1
Nut, Elevation
* Screw, Type =T" Hex Washer
Hd. 5/16-18 x 3/4
• Screw, Hex Hd. 5/16-18 x 1
* Screw, Hex Hd. 5/16-18 x 1/2
* Nut, Hex 3/8-16
* Lockwasher, 3/8
* Washer, .380 x 7/8 x 1/8
*Screw, Hex Hd. 3/8-16 x 1-1/4
• Screw, Hex Hd. 5/16-18 x 1-7/8
Screw, Locking Cap114-20 x 5/8
Bolt, Hex Hd. 5/16-18 x 1-7/8
High Strength
Bolt, Hex Hd. 5/16-18 x 1-1/2
High Strength
Support, LH.
Shaft, Elevating
Washer, Thrust .502 x .927
x .031
Bearing

3 BASE ASSEMBLY

Key
No
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47

Part
No.
60300
818164
STD541450
63619
STD541031
STD541431
STD581037
_818165
63617
STD551050
STD581050
821333
STD541025
STD551125
63622
63435
STD551012
STD522.505
STD502503,
63434
63621
818199
STD551031
STD551131
109163

* Standard Hardware Item- May Be Purchased Locally.

Description
Washer, 1/2 x 7/8 x .010
(as required)
Gear, Bevel
* Nut, Lock 1/2-13
Support, R.H.
* Nut, Hex 5/16-18
* Nut, Lock 5/16-18
* Ring, Retaining 3/8
Gear, Pinion
Bearing, Elevating Shaft
* Washer, .515 x .875 x .032
• Ring, Retaining 1/2
Shaft, Elevating Crank
• Nut, 1/4-20
* Lockwasher 1/4
Bracket, Bearing
Bushing
* Washer, 17/64 x 9/16 x 3/84
• Screw, Hex Hd. 1/4-20 x 1/2
* Screw, Soc. Set 1/4-20 x 3/8
Crank, Elevating
Base
Channel, Table Mounting
• Washer, 11/32 x 7/8 x 1/16
* LodoNasher, 5/16
• Bolt, Square Hd 5/16-18 x 3/4

(1)
"O
mll

"O
(n

Repair Parts
PARTS LIST FOR CRAFTSMAN
10" RADIAL SAW
MODEL NUMBERS 113.196320 & 113.196420
4

4
3

1
13

FIGURE
Key
No

Part
No.

Description

1
2
3
4
5
6
7

821343
60314
63751
63750
STD551225
STD541025
STD523106

Leg
Screw, Truss Hd. 1/4-20 X 5/8
Stiffener, R.H.
Stiffener, L.H.
* Lockwasher, External 1/4
* Nut, Hex 1/4-20
* Screw, Hex Hd 5/16-18 x 5/8

6 - LEG SET
Key
No

Part
No.

8
9
10
11
12
13

STD551031
STD551131
STD541231
STD541037
803835-1
821360

Description

* Washer, 11/32 x 11/16 x 1/16
* Lockwasher, External 5/16
* Nut, Hex Jam 5/16-18
* Nut, Hex 3/8-16
Foot, Leveling
Lower Stiffener
(113.196420 Only)

° Standard Hardware Item may be Purchased Locally.

owner's
manual

10-1NGH

SAW

SERVICE

Now that you have purchased your 1[]-Inch radial saw, should a
need ever exist for repair parts or service, simply contact
any
Sears Service Center and most Sears, Roebuck and Co. stores.
Be sure to provide all pertinent facts when you call or visit.

MODEL NO.
113.196120

The model number of your 1D-inch radial saw will be found
label attached to your saw, at the front of the base.

on a

SAW ONLY
or

113.196320
SAW WITH LEGS
or

113.196420
CONTRACTOR'S

SAW

HOW TO ORDER
REPAIRPARTS

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING
INFORMATION:
PARTNUMBER

PARTDESCRIP11ON

MODEL NUMBER
113.196120
113.196320
113.196420

NAME OF ITEM
10-INCH RADIAL SAW

All parts listed may be
and most Sears stores.
locally, your order will
Repair Parts Distribution

Sold by SEARS, ROEBUCK AND CO.,
Part No. SP5599

Form

No. SP5599-1

ordered from any Sears Service Center
If the parts you need are not stocked
be electronically
transmitted
to a Sears
Center for handling.

Chicago,

IL 60684

U.S.A.
Printed

in U.S.A. 2/93

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 80
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Mon Jul 21 01:50:04 2008
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 113196120 User Manual RADIAL SAW Manuals And Guides L0804093

CRAFTSMAN Saw Radial Manual L0804093 CRAFTSMAN Saw Radial Owner's Manual, CRAFTSMAN Saw Radial installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation