Craftsman 113206933 User Manual 61/8 INCH JOINTER PLANER Manuals And Guides L0709234

CRAFTSMAN Jointer/Planer Manual L0709234 CRAFTSMAN Jointer/Planer Owner's Manual, CRAFTSMAN Jointer/Planer installation guides

User Manual: Craftsman 113206933 113206933 CRAFTSMAN CRAFTSMAN 61/8-INCH JOINTER-PLANER - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 61/8-INCH JOINTER-PLANER #113206933. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 61/8-INCH JOINTER-PLANER Manual

Open the PDF directly: View PDF .
Page Count: 32

Save This Manual

For Future Reference

SEARS

MODEL NO.

1"l3.206933

JOINTER/PLANER WITH

LEGS AND MOTOR

Serial

Number

Model and serial

number may be found

on a plate attached

to your base,

You should record both

model and serial number

in a safe place for

future use.

CAUTION:

Read GENERAL

and ADDITIONAL

SAFETY

iNSTRUCTiONS

carefully

6-1/8-iNCH JOINTER-PLANER

®assembly

•operating

erepair parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.SoA,

Part No. 67096 :Prir_ted Lr_U_S

general safety instructions for power tools

1. KNOWYOUR POWER TOOL

Readand understand the owner's manual and

labels affixed to the too!. Learn its application

and limitations as we_l as the specific potential

hazards peculiar to this tool.

2. GROUND ALL TOOLS

This tool is equipped with an approved

3-conductor cord and a 3-prong grounding type

plug tofit the proper grounding type receptacle.

he green c0nductor inthe cord is the grounding

wire. Never connect the green wire to a live

terminal.

3. KEEP GUARDS IN PLACE,

in working order, and in proper adjustment and

alignment.

4. REMOVE ADJUSTING KEYS AND WRENCHES

Form habit of checking to see that keys and

adjusting wrenches are removed from tool before

turning it on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents,

Floor must not be slippery dueto wax or sawdust.

6. AVOID DANGEROUS ENVIRONMENT

Don't use power tools in dam p or wet locations or

expose them to rain. Keep work areawell lighted.

Provideadequate surrOunding work space,

7. KEEP CHILDREN AWAY

All visitors should be kept a safe distance from

work area.

8. MAKE WORKSHOP CHILD-PROOF

-- with padlocks, master switches, or by removing

it will do the job better and safer at the rate for

which it was designed.

10. USE RIGHT TOOL

Don't force tool or attachment to do a job it was

not designed for.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves neckties o[

ewelry (rings, wrist watches) to get caught in

moving parts. Nonslip footwear is recommended,

Wear protective hair covering to contain tong

hair, Roll long sleeves above the elbow.

12, USE SAFETY GOGGLES (Head Protection)

Wear Safety goggles (must comply with ANSI

Z87,1) at all times. Everyday eyeglasses only

have impact resistant lenses, they are NO1-

safety glasses. Also. use face or dust mask if

cutting operation is dusty, and ear protectors

(plugs or muffs) during extended periods of

operation.

13. SECURE WORK

Use clam ps or av_seto hold work when practical.

it's safer than using your hand, frees both hands

to operate tool.

14. DON'T OVERREACH

Keep proper footing and balance at alt times.

15. MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest

performances, Follow instructions for lubricating

and changing accessories.

16. DISCONNECT TOOLS

before servicing; when changing accessories

such as blades, bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before

plugging in.

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended

accessories. Follow the instructions that accom-

pany the accessories. The use of improper acces-

sories may cause hazards.

19. NEVER STAND ON TOOL

Serious injury could occur if the tool is tipped or

if the cutting tool is accidentally contacted. Do

not store materials above or near the too! such

that it is necessary to stand on the tool to reach

them.

20. CHECK DAMAGED PARTS

Before further use of the tool. a guard or other

part that is damaged should be carefully checked

toensurethat it will operate properly and perform

its intended function. Check for alignment of

moving parts, binding of moving parts, breakage

of parts, mounting, and any other conditions that

may effect its operation. A guard or other part

that is damaged should be properly repaired or

replaced.

21. DIRECTION OF FEED

Feed work into ablade or cutter against the

direction of rotation of the blade or cutter only.

22. NEVER LEAVE TOOL RUNNING UNATTENDED

Turn power off. Don't leave too! until it comes to

acomplete stop.

additional safety instructions for jointer-.planer

Safety is a combination of operator common sense and

alertness at all times when the Jointer-Planer is being

used.

WARNING: FOR YOUR OWN SAFETY, DO NOT AT-

TEMPT TO OPERATE YOUR JOINTER-PLANER UNTIL

IT IS COMPLETELY ASSEMBLED AND INSTALLED

ACCORDING TO THE INSTRUCTIONS., . AND UNTIL

YOU HAVE READ AND UNDERSTOOD THE FOLLOW-

ING.

PAGE

1. GENERAL SAFETY INSTRUCTIONS FOR POWER

TOOLS ..................................... 2

2. GETTING TO KNOW YOUR JOINTER-PLANER 11

3. BASIC MACHINE OPERATION ................ 17

4. USE OF HOLD-DOWN/PUSH BLOCKS ......... 18

5. MAINTENANCE ............................. 19

6. STABILITY OF MACHINE

If there is any tendency for the Jointer=Planer to tip

over or move during certain operations such as when

pJaning or jointing long heavy boards, the Jointer =

Planer (stand) should be bolted to the floor.

7. LOCATION

The Jointer-Planer should be positioned so neither

the operator nor a casual observer is fo rced to stand in

line with the wood while it is being planed.

This machine is intended for indoor use only. Provide

adequate lighting.

8. KICKBACKS

Kickbacks can cause serious injury. A kickback occurs

when the operator looses control of the workpiece

causing it to be kicked back toward him.

Kickbacks- and possible injury from them can usuaf_y

be avoided by:

a, Holding the workpiece firmly against tables and

fence.

b. Not taking too deep acut at one time, A deep cut

req uires more effort to feed the wood while planing

and can cause the wood to kickback. A cut between

1/32 and 1/16 of an inch deep wil_ produce the best

results.

9_ PROTECTION: EYES, HANDS, FACE, EARS, BODY

a. If any part of your jointer is malfunctioning, has

been damaged or broken .. such as the mo:or

Switch, or other operating controF, a safety device

or the power cord.., cease operating immediately

until the particular part is properly repaired or

replaced

b. Wear safety goggles that comply with ANSI Z87.1

and a face shield if operation is dusty. Wear ear

plugs or muffs during extended periods of operation,

c. Do not plane, joint, or bevel wood shorter than 12

in. Smaller pieces of wood can tip over on the

tables, or into the cutterhead and be kicked back

toward you.

d. Always use the hold down/push block when j ointing

or beveling wood narrower than 3 in. but never joint

or bevel wood narrower than 3/4 in., or less than t/4

inch thick.

e. Always use the hold down/push blocks when

planing wood thinner than 3 in. but never piane

wood thinner than 1/2 in. under any circumstances.

f. Avoid awkward hand positions, where a sudden

slip could cause a hand to move into the cutters.

g. Never turn your Jointer-Ptaner "ON" before cleadng

the table(s) of all objects (toots, scraps of wood,

etc.) except for the workpiece and related feed or

support devices for the operation planned.

h. Make sure the cutterhead revolves in the right

direction, (toward the infeed table).

i. KEEP CUTTER GUARD IN PLACE AND OPERAT-

ING PROPERLY AT ALL TIMES. Regularly check

the tension of the cutter guard spring to assure

satisfactory operation. (See Getting To Know Your

Jointer-Ptaner section.)

j. Always feed the wood completely through the

cutter head and past the cutter guard so that the

guard returns to the rest position against the fence,

When using only one hold down/push Mock to feed

the wood, do not place your other hand on the

Jointer-Planer.

k. Always maintain complete control of the work piece

and provide adequate support for iong and heavy

workpieces.

smaller than recommended. (See section in this

manual, "Basic Jointer_Piane_r operations, ')

Smaller pieces of wOOd can tip over on the tables;

or into the cutter head and can be kicked back

toward you,

d, Keeping blades sharp. Blades that are dull or

nicked require more effort while p_aning and wlli

tend to pound the wood rather than cut it, which

can cause the wood to kickback. A nicked blade will

cut a ridge in your wood and cause the wood to ride

up on the outfeed table. Make sure the cutter blades

are installed properly, and cutter blade wedge

screws are tight.

Not jointing, planing, or beveling pieces of:wood I0, Warped wood should be surface planed on the concave

side for best resutts_

11. To avoid a rough planed surface, determine if possible,

which way the grain emerges from the wood and feed

the wood accordingly.

GRAIN EMERGING

ROTATION

!2, Do not plane edges of plywood, composition materials,

or wood that has gtue o,n it or is painted or varnished.

Planing these materials will dutl the blades quickly.

beyond

the :desired

15. Never leave the Jo "work area:with the

power on, before the Jo nter-Planer has come to a

complete stop; Or without removing and storing the

switch key. :

t6: Never operate the Jointer-Pla ner with protective cover

on the unused shaft end of the motor removed.

17. Do not attempt to perform an abnormal or little-used

operation without study and the use of adequate hold

downtpush blocks, jigs, fixtures, stops, etc.

18: DO NOT perform layout, assembly, or setup work on

the table white the cutting _ool is rotating,

WARNING_ THE 2" JOINTER-PLANER PULLEY AND

THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN

THE CUTTER HEAD AT APPROXIMATELY 4300 RPM

ns for jointer-pmaner

EN USED WITH A 3450 RPM MOTOR, NEVER

SUBSTITUTE OTHER PULLEYS TO INCREASE THIS

SPEED BECAUSE iT COULD BE DANGEROUS.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED

FROM FREQUENT USE OF YOUR JOINTER-PLANER)

BECOME COMMONPLACE. ALWAYS REMEMBER

THAT A CARELESS FRACTION OF A SECOND IS

SUFFICIENT TO INFLICT SEVERE INJURY.

19. Read and follow the instructions appearing on the

danger label on the cutter guard.

DANGER -FOR YOUR OWN SAFETY

READ AND UNDERSTAND OWNER'S

MANUAL SEFORE OPERATING MACHINE

1. WEAR SAFETY GOGGLES PER ANSI Z87.f AT ALL TIMES.

2, NE_VER PERFORM A JOINTING OR PLANING OPERATION WITH CUTTER

HEAD OR DRIVE GUARD REMOVED.

3. NEVER MAKE A JOINTING OR PLANING CUT DEEPER THAN 1/8 INCH,

4, ALWAYS USE HOLD DOWN/PUSH BLOCKS FOR JOINTING MATERIAL

NARROWER THAN 3 INCP_ES, OR PLANING MATERIAL THINNER THAN 3

INCHES.

WEAR YOUR

The operation of any power tool can result in foreign

objects being thrown into the eyes. which can result in

severe eye damage. Always wear safety gogg les complying

with ANSI Z87.1 (shown on Package) before commencing

power too_ operation, Safety Goggles are available at

Sears retail or catalog stores.

contents

POWER TOOL GUARANTEE ........ 2

GENERAL SAFETY INSTRUCTIONS FOR

POWER TOOLS ............... ................. 2

ADDITIONAL SAFETY INSTRUCTIONS FOR

JOINTER-PLANER ............................. 3

MOTOR SPECIFICATIONS AND ELECTRICAL

REQUIREMENTS.. ............................ 5

Connecting to Power Source Outlet ............. 5

Check Motor Rotation ......................... 5

UNPACKING AND CHECKING CONTENTS ......... 6

ASS EMBLY ..................................... 7

Assembling Steel Legs ........................ 7

Mounting Jointer-Planer On Recommended

Craftsman Leg Set .......................... 8

Checking Cutterblades and Screws ..............

Mounting Switch .............................. 9

Installing Motor, Pulley, V-Belt and Belt Guards...9

Fence Locks and Stops ...................... 12

Fence Tilt Scale ............................ 12

Cutter Guard ............................... 13

Infeed Table ................................ 14

On-Off Switch .............................. 16

BASIC JOINTER-PLANER OPERATION ........... 17

Feeding the Workpiece ........................ 17

Using the Hold Down/Push Blocks ............. 18

Beveling ................................... 19

MAINTENANCE ................................ 19

Replacing Cutter Blades ..................... 19

Installing Cutter Guard Spring ................ 21

Sharpening Cutter Blades .................... 23

GENERAL MAINTENANCE ...................... 23

LU BRfCATI ON ................................. 23

MOTOR MAINTENANCE AND LUBRICATION ...... 24

TROUBLE-SHOOTING .......................... 24

Installing Sliding Guard ...................... 10 REPAIR PARTS ................................ 26

GETTING TC) KNOW YOUR JOINTER-PLANER. ,o, .11 RECOMMENDED ACCESSORIES ................. 31

DePth of CutHandWhee_ .:. _... ,_ .... .... ;* -o ! 1

motor specifications and

This machin6 is designed to use a 3450 RPM motor only.

Do not use any motor that runs faster than 3450 RPM. It is

wired for operation on 110-120 volts, 60 Hz., atternating

current, IT MUST NOT BE CONVERTED TO OPERATE

ON 230 VOLTS. EVENTHOUGH SOME OFTHE RECOM-

MENDED MOTORS ARE DUAL VOLTAGE.

THESE CRAFTSMAN MOTORS HAVE BEEN

FOUND TO BE ACCEPTABLE FOR USE ON

THIS TOOL.

HP RPM VOLTS CATALOG NO.

1/2 3450 110-120 12!6

1/2 3450 110-220 1218

3/4 3450 110-120 1219

3/4 3450 110-120 1226

CAUTION: Do not use blower or washing machine motors

or any motor with an automatic reset overload protector as

their use may be hazardous.

CONNECTING TO POWER SOURCE OUTLET

This machine must be grounded while in use to protect the

operator from electric shock.

Plug power cord into a 110-120V properly grounded type

outlet protected by a !5-amp, dual element time delay or

Circuit-Saver fuse or circuit breaker.

If you are not sure that your outlet is properly grounded,

have it checked by a qualified electrician.

WARNING: DO NOT PERMIT FINGERS TO TOUCH THE

TERMINALS OF PLUGS WHEN INSTALLING OR

REMOVING THE PLUG TO OR FROM THE OUTLET,

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED

IN DAMP LOCATIONS IN PROXlMITYTO PLUMBING. IF

AN ELECTRICAL SHOCK OCCURS THERE IS THE

POTENTIAL OF A SECONDARY HAZARD SUCH AS

YOUR HANDS CONTACTING THE CUTTING BLADE.

If power cord is worn or cut, or damaged in any way, have

it replaced immediately.

PROPERLY

GROUNDED

OUTLET\

3--PRONG

GROUNDING

PRONG

This power too! is equipped with a :?,-conductor cord and

grounding type plug which has a grounding prong listed

by Underwriters_ Laboratories Association. The ground

conductor has a green jacket and is attached to the tool

housing at one end and to the ground prong in the

attachment plug at the other end.

This ptug requires a mating 3-conductor grounded type

outlet as shown.

electrical requirements

If the outlet you are planning to use for this power tool is of

the two prong type DO NOT REMOVE OR ALTER THE

GROUNDING PRONG tN ANY MANNER. Use an adapter

as shown and always connect the g rounding lug to known

ground.

It is recommended that you have aqualified electrician

replace the TWO prong outlet with a property grounded

THREE prong outlet.

A temporary adapter as shown betow is available for

connecting plugs to 2-prong receptacles. The green

grounding lug extending from the adapter must be con-

nected to a permanent ground such as to a properly

grounded outlet box.

A temporary adapter as illustrated is available for con-

necting plugs to 2-prong receptacles. The temporary

adapter should be used only until a properly grounded

outlet can be installed by a qualified electrician.

GROUNDING LUG

t_1 MAKE SURE THIS IS

3-PRONG _L- _, _._--'*_-'_-_ CONNECTED TO A

PLUG I ll KNOW.GROU.O

/RECEPTACLE

ADAPTER

WARNING: THE GREEN GROUNDING LUG EXTENDING

FROM THE ADAPTER MUST BE CONNECTED TO A

PERMANENT GROUND SUCH AS TO A PROPERLY

GROUNDED OUTLET BOX, NOT ALL OUTLET BOXES

ARE PROPERLY GROUNDED.

tf you are not sure that your outlet is properly grounded,

have it checked by a qualified electrician.

NOTE: The adapter illustrated is for use only if you already

have aproperly grounded 2-prong receptacle.

The use of any extension cord will cause some toss of

power, To keep this to a minimum and to prevent over-

heating and motor burn-out, L_se the table below to

determine the minimum wire size (A.W.G.) extension

cord. Use oniy 3 wire extension cords which have 3 prong

grounding type plugs and 3-pole receptac}es which wif_

accept the plug on the saw

Extension Cord Length Wire Size A.W.G.

Up to 100 Ft. 14

100 - 200 Ft. 12

2OO- 4OOFt 8

CHECK MOTOR ROTATION

Place the motor on your workbench or on the floor.

Standing clear of the motor shaft, plug the motor cord into

a properly grounded outlet. Notice the rotation of the

shaft. As you look directly at the motor shaft it shoutd be

turning in the counterclockwise direction,_--'_, if the

motor shaft is turning counterclockwise, remove the plug

from the power outlet and continue the assembly pro-

cedures If the motor isturning clockwise, remove the piing

from the power outlet and contact your Sears Store

immediately.

-//

d checking contents

TABLE OF LOOSE PARTS

Item

No. Description Qty.

AJointer-Planer .............................. 1

7/:16" Wrench __

3/4°'_Wrench

3/8" Wrench Medium Screwdriver

M0def:113.206933 Jointer-Planer is shipped complete in

onecarton and INCLUDES Steel Legs, and Motor.

Separate all parts from packing materials and check each

onewith the illustration and the list of Loose Parts to make

certain all items are accounted for, before discarding any

packing material.

If any: parts are missing, do not attempt to assemble the

jointer/planer_ plug in the power cord or turn the switch on

until the missing parts are obtained and are installed

correctly.

Remove the protective oil that is applied to al{ unpainted

metal surfaces. Use any ordinary household type grease

and spot remover.

WARNING: Never use gasoline, naptha or similar highly

volatile solvents.

Apply a coat of paste wax to the table.

Wipe all parts thoroughly with a clean, dry cloth.

WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT

PLUG TO POWER SOURCE OUTLET UNTIL ALL

ASSEMBLY STEPS ARE: COMPLETE, AND YOU HAVE

-READAND UNDERSTAND THESAFETY AND OPERA-

T| ONAL INSTRUCTION S.

B V-Bett_ 1,/2 x52"............................ 1

*C 5/32 Setscrew Wrench ....................... 1

*D 1/8 Setscrew Wrench ........................ 1

*E Motor Pulley, 2-1/2" Dia ...................... 1

*F Sliding Guard Knob ......................... 1

*G Concave Plastic Washer ..................... 2

H Sliding Guard .............................. 1

*J Sliding Guard Rod .......................... 1

*K Nut, 1/2-13 ................................. 1

*L Lockwasher, 1/2 ............................ 1

*M Lockwasher. No. 10 ......................... 2

*N Screw, Pan Hd., 10-32 x 1/4 ................... 2

O Owners Mariu!! .............................. 1

*P Depth of Cut Handwheet ..................... 1

*Q Screw, Sems, 1/4-20 x 1-1/4 .................. 1

R On/Off Power Outlet ........................ 1

*S Washer, 17/64 x 1/2 x 1/32 .................... 2

"T Lockwasher. External 1/4 .................... 2

*U Screw, Pan Hd. 1/4-20 x 1/2 .................. 2

V Jointer-Planer Belt Guard .................... 1

*W Attaching Hardware (2 Nuts, 2 Bolts)

X Belt Guard Clips ............................ 3

Y Bracket. Mounting ......................... 1

Z Beft Guard Support Bracket .................. 1

AA Bett Guard Support ......................... 1

AB Screw Pan Hd. 10-32 x 1/2 .................... 2

AC Motor Pulley Belt Guard ..................... 1

AD Switch Key ................................ 1

AE Hold Down/Push Block ...................... 2

AF Fence ..................................... I

........ Fence ............................... I

*Supplied in Loose Parts Bag #507437

\ \

AD AE

Item

No.

unpacking and checking contents

TABLE OF LOOSE PARTS

TheFollowingPartsAreIn iudedWith

Model 113,206933 Only

DescripUon Qty.

ALeg, .4

B End Stiffener ............................... 2

C Side Stiffener .............................. 4

D Motor Support .............................. 1

E Motor ..................................... 1

Package of Miscellaneous Small Parts,

No. 67035, Consisting of the Following:

F Cord Clip .................................. 2

G Hex Nut, 1/4 in.-- 20

(approx. dia. of hole 1/4 in,) ................ 40

G Hex Nut, 5/16 in,-- 18

(approx. dla. of hole 5/16 in.) ................ 7

G Hex Nut, 1/2 in.-- 13

(approx. dia. of hole 1/2 in.) ................. 8

H TrussHd. Screw, 1/4in. --20x5/8 tn.

long. (Top of screw is rounded) ............. 40

J Flat Washer (dia. of hole 11/32 in.) ............. 7

K Lockwasher, 1/4 in. External Type

(approx. dia. of hole 1/4 in.) ................ 40

K Lockwasher, 5/16 in, External Type

(approx. dia. of hote 5/16 in.) ................ 7

L Carriage Bolt, 5/16 in. -- 18 x 3/4 tong .......... 3

M Leveling Foot .............................. 4

N Hex Hd. Screw, 5/16 in. -- 18 x 2 in ............. 3

ii i,, i ..................................

assembly

ASSEMBLING STEEL LEGS

NOTE: Steel Legs are furnished with Model 1t3.206933.

From among the foose parts, find the foilowin 9 Hardware:

40 Truss Head Screws, I/4-20 x 5/8

40 Lockwashers, 1/4-External

40 Hex Nuts, !/4-20

8 Hex Nuts, t/2-13

4 Leveling Feet

1. Assemble two (2) Side Stiffeners together Using four

(4) 1/4-20 Truss head screws, tockwasher and nuts.

Make two (2) Side Stiffener assemblies. I

The End Stiffeners are placed on top and at each end

of Side Stiffener assemblies as shown. Align holes,

letter coded "B" (see page 8) in Side Stiffeners and ....-._ .....

End Stiffeners and then insert 1/'4-20 Truss head

screws through the 9/32 diameter hotes and install

Iockwashers and nuts and then tighten.

2. Assemble the four (4) Legs to the Side and End

Stiffeners using 1/4-20 screws, lockwashers and nuts

as sh own, i

TRUSS HD. SCREW END STIFFENER

1/4-20 X_1/: EXTERNAL /

END 1LOCKWASHER __

MOTOR SUPPORT

STIFFENERS

LEGS

3. Assemble the Motor Support to the Legs with 1/4-20

screws, Iockwashers and nuts. Motor Support can be

assembled to either end of Leg set.

4. Install leveling feet as shown. To level Leg Set, loosen

nut on inside of leg and turn nut on the outside to raise

or lower feet. Adjust all four leveling feet, if necessary,

and then tighten nuts on the inside of leg.

NOTE: These levelers are not intended for height

adjustment:

1. Place fence on jointer table as shown.

2_ Locate the following parts from the loose parts bag

and install as shown.

1. CarriageBolt, 3/8-16 x 24/2

2. Retainer

3, Fiat Washer 13/32 x13/! 6 x 1/t6

4. Spacer

5. =Knob

1 2 JOINTER eASE

SPECIAL NOTE: It is a good _dea at this point to see ifthe

infeed table and Outfeed table are paraltel to each other. If

it is necessary to align the two tables the procedure used

to make them parallel can be more easily performed now,

before mounting the jointer/planer to the leg set, Refer to

page 14 for directions explaining how to check and align

the infeed and outfeed tables.

MOUNTING JOINTER-PLANER

1. From among the loose parts, find the following hard-

ware:

assembly

7 Lockwashers, 5/16 in. External Type

7 Washers, 11/32 ID

7 Hex Jam Nuts, 5/16-18

2Cord Clips

2. Loosen FENCE LOCK KNOB, Tilt fence upward and

slide it toward the pulley.

3. Position machine on Leg Set and align mounting holer

in machine with holes in Leg Set letter coded "A'.

Mount with three (3) 5/16-18 x 2" Long Hex Head

Screws.

4. Place aflat washer, a tock washer and a nut on each

screw from underneath the stand and tighten.

5. Place handwheet on shaft aligning flat surfaces on

shaft with flat surfaces on handwheel.., attach with

1-1/4 in. screw.

_1_/JOINTER ;PLANER

HEX HEAD SCREW

HEXNOTff'_ Jl

FENCE LOCK KNOB

4Carriage Bolts, 5/16-18 x3/4

3 Hex Head Screws, 5/16-18 x2

_/4-_0 TRUSS

HEAD SCREW SIDE STIFFENER

--- MOTOR SUPPORT AT THIS END

11 1

CHECKING CUTTER BLADES AND SCREWS

TOOLS NEEDED

5/32" and 1/8" Setscrew Wrenches (furnished with

Jointer).

Lead Pencil

FLAT WASHER

(AS REQUIRED) ..

LOCKWASHER

NUT ----"_

5/32 IN. SETSCREW

OUTFEED TABLE WRENCH

WEDGE

DEPTH OF CUT

Short straight edge (or head of combination square)

1. Insert pencil in space at end of cutterhead to hold

cutterhead guard open.

2. Lower the infeed table with the Depth of Cut Hand-

wheel.

3. Rest the straight edge on edge on the surface of

outfeed table so itextends across the opening between

the tables, at three positions: near each end and at the

middle of the cutter blade.

4. Rotate the cutterhead by grasping the 2" dia. driven

pulley and make sureeach knife nicks (touches) the

straight edge at all three positions. If not, follow

BLADE

PENCt L\

CUTTER GUARD

procedure under "REPLACING CUTTER BLADES"

on pgs, 19 thru 21.

5. If a cutter blade adjustment is not required, check

each locking screw of each wedge (5/32" setscrew

wrench) and tighten if necessary. Hold the pulley

,i i--

MOUNTING SWITCH

1, Locate the following parts:

1On/Off Power Outlet

2 Pan Hd. Screws, 1/4-20 x 1/2

while tightening screws and be careful that your

fingers do not slip off the wrench-

2 Lockwash_rS, IE;<te real 1/4

2 Washers, 17/64 × 1/2 x1732

2. Attach On/Off out|et to infeed table using two _apped

holes.

iL __

INSTALLING MOTOR, PULLEY, V-BELT AND BELT

GUARDS

1. Locate the following parts:

QIy. Description

1 Motor

1 "L" Bracket

1Pulley (Approx. 2-1/2" Dia.)

1 V=Belt 1/2 x 52

4Carriage Bolt 5/16-18 x3/4

4Fiat Washer 5/16 i.D.

4 Lockwasher5/16 I.D.

4Hex Nut 5/16-!8

1 Guard Assembly _nctuding a guard support,

guard support bracket, self-threading screws,

and clips,

2. Place motor against the motor mounting bracket and

insert bolts through holes in motor base and then

through holes marked "X" in motor mounting bracket.

DO NOT TIGHTEN BOLTS AT THiS TIME. The "L"

bracket which holds the guard support must be slid

between the motor base and the motor mounting

CARRIAGE BOLT

5/16-18 x 3/4

MOTOR ti

VtEW FROM BACK OF JOINTER

BOLTS GO THRU HOLES MARKED "X"

bracket somotor rn u st be loosely assembled to bracket

at this time.

iii, IH i, iiiiiiii, ii

(

3. Slide long leg of "L" bracket between motor base and

motor mounting bracket. Then sandwich the short leg

of the "L" bracket between the guard support bracket

and the guard support and loosely fasten together

with self-threading screws as shown. Install clips onto

bett guard support with long end of clip facing you.

L¸ i_ jill! i

TWO HOLES CLOSEST

10-32 X 1/2 IN,

SELF-THREADING

suP.oRT

i i i i !l , i iiiiii i _ url III

2"!/2 '° MOTOR PULLEY

4. Install the 2-1/2" pulley onto the motor shaft and

t_ghten the set screw in the pulley hub against the flat

part of the motor shaft.

5/32 INCH

SETSCREW TIGHTEN

WRENCH S_T SCREW

AGAINST FLAT

,ON SHAFT

HERE WITH

MOTOR SHAFT

assembly ,

.5/Push V_Belt through belt guard just enough to loop

.belt aro'uhd motor pulley_ Place bett: around m0t()r

pu ey but don0t push guard onto guard support at

:thistime. "---

6: Position other end of V-Belt onto cutter head pulley.

/ , i

7. Visually line up both pulleys and V-Belt until they are

perpendicular to the floor by sliding motor sideways

as needed,

8. Pressdown hard on motor to put tension on the V-Belt

and tighten the motor mounting bolts at this time.

9. Checkguard support before tightening guard support

screws to be sure it is centered around motor shaft and

will not rub against shaft when motor msrunning.

Tighten screws,

10. Push motor pulley belt guard into position onto guard

support.

tl. Plug motor cord into outlet on switch box installed

earlier through hole provided in stand.

12. Fasten cord along front side stiffener using the two

cord clips.

ii i

INSTALLING SLIDING GUARD

OPEN END

i i

PARTS NEEDED

1Sliding Guard

1Sliding Guard Knob

I Sliding Guard Rod

2 Sliding Guard Washers (one side of washer is concave)

2Hex Hd. Screws 1/4-20x 1/2"

PULLEYS AND V-B ELT

j_MUST BE STRAIGHT IN-LINE

_AT 90°WITH RELATIONSHIP

C_____ TO THE FLOOR

t,----V-BELT

GUARDS REMOVED

..... ! FOR PICTURE CLARITY

i, t STRAIGHT LNE

// _,] \ , UP--DOWN

90°

.... iJ, [_

ill

2 Hex Nuts 1/4-20

1 Hex Nut 1/2 in. - 13

1 Split Iockwasher 1/2 in,

2 Ext. tooth Iockwashers

2 10-32 x 1/4 Pan Hd. Screws

1 Belt Guard

3, Screw the sliding guard rod into the jointer as far as it

witl go with the short end of rod pointing straight up.

4. Tighten the 1/2" nut to hold the rod securely in this

position.

_I,POsitiOn the siiding:guard rod through the opening in

the belt guard as illustrated. 1/2" LOCKWASHER

2. Screw 1/2 °' nut alt the way onto long end of rod... \_ BELT

place 1/2" Iockwasher next to nut (as illustrated), _/i/4_:_ _ GUARD

1/2" X t _/ .//_ \SLIDING

HEX NUT [i _/ GUARD ROD

1/2" HEX NUT

GUARD ROD

5. Attach guard to stand with hex hd. screws and nuts,

Make sure belt does not scrape guard,

SLIDING GUARD KNOB

6. Attach sliding guard to fence with two pan head 10-32xl/4 SCREWS'_',,_

screws and Iockwashers. EXT. TOOTH

7. PtaceoneSIidingGuardWasher, concaveside DOWN LOCKWASHERS

on support rod.

8. Drop sliding guard onto rod.., place other washer,

concave side UP on rod.. _screw on Sliding Guard

Knob.

_,^o==o,,M=,,,_,_ '

(CONCAVE S|DE UP)

i,, u,i i llUl ,1= == ===LI H i i

getting to know your jointer-planer

WARNING: FOR YOUR OWN SAFETYTURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE MAKING ANY ADJUSTMENTS.

FENCE TILT SCALE

(BEHIND FENCE)

FENCE

LOCK

KNOB

FENCE

OUTFEE{) TABLE

SLIDING GUARD

FKNOB

BACK OF

JOINTER

INFEED

TABLE

SLIDE

BRACKET

FRONT OF \, %

JOINTER 4 CUTTER GUARD 6 ON-OFF DEPTH OF CUT

SWITCH 1HANDWHEEL

1NFEED DEPTH OF CUT

..41 TABLE

=DEPTH OF CUT HANDWHEEL Turning the hand- /

IHANDWHEEL

wheel counterclockwise will lower the infeed table _"_---_+.'

to maximum depth of 1/8 in. UP

/.i

/DOWN

I"1

-= FENCE LOCKS AND STOPS.= The fence can be

moved across the Jointer to take full advantage of

1he "sharpness_' Of the blades.

Thb fence should be positioned to the extreme right

(toward pulley) but not beyond the end of the

blades.

Most of the cutting (usually jointing) will be done

-. w_th thefence in this position, As the blades become

•.dull, the fence can be moved toward the left where

the blades are sharper,

To move the fence, loosen the Fence Lock Knob and

the Sliding Guard Knob and slide to desired position.

Make sure SLIDE BRACKET is even with surface of

OUTFEED TAB LE. If it is above or below the surface,

loosen screws and adjust it.

a. Always tighten fence lock knob first to align

fence, then tighten sliding guard knob.

b. Before tightening fence lock knob, hold fence

down on outfeed table so it does not rock.

c. 90 °Fence Stop positions fence square to tables.

TO tilt fence, loosen the fence lock knob and

sliding lock knob and pull the stop out. Tilt to

desired angle and tighten both knobs.

d. To set fence at g0 °to tables, loosen the two

knobs, tilt fence so the stop springs back into

place. Tilt fence back so the stop rests on the

table and tighten both knobs.

e. 45 ° Fence Stop positions the fence at 45 ° to the

tables.

f. To tilt fence to 45 °loosen the two knobs, pull 90°

stop out, t It:fence so the 45 ° stop rests on the

table.

g. Ho d fencedown on outfeed table and tighten the

twokn0bs: " " :' : :

i i i i ii i i

. FENCE TILT SCALE. Indicates tf_e angle of the

fence to the tables. When the 90 _ fence stop is

correctly adjusted, the fence will be 90 °to the table

and the scale will read 90 °.

To check for squareness, place an accurate square

PUSH DOWN

WHEN LOCKING

FENCE LOCK KNOB

FENCE

45°FENCE

STOf

_°FENCE

STOP

FENCE LOCK .

KNOB \\

SLIDING GUARD KNOB

SLIDE BRACKET

._..---FENCE TILT SCALE

on infeed table and check fence while locked at 90°

position. MAKE SURE 90° STOP IS AGAINST SLIDE

BRACKET.

If fence is not square to table:

a. Slightly loosen fence lock knob and guard lock

knob ....

FENCE

FACE

SQUARE

"CUTTER

GUARD

1NFEED

TABLE

b. Loosen 90° stop screw with small screwdriver

and turn knurled sleeve which will cause fence to

tilt, Turn sleeve in either direction until fence is

square with infeed table.

NOTE: If you cannot square fence by turning

knuded sleeve, loosen three screws "A" and

adjust fence square to table.

c. Tighten 90° stop Iockscrew and both fence lock

knobs,

d, If 90° reading on tilt scale does not line up with

top surface of the slide bracket, loosen screws

holding scale and move it... tighten screws.

45 =STOP

KNURLED J_

SLEEVEN_(

90 eSTOP

e. Adjust 45°stop in the same manner.

NOTE: Tilt scale wilt not require adjustment if it

was adjusted for 90 ° position.

45_'STO_

90°STOP

HEAD

SQUARE

FENCE

SCALE

ADJUSTING

SCREW

_s o sToP

LOCKSCREW

TiLT

SCALE

'gO '_ STOP

LOCKSCREW

SCALE

AD3USTING

SCREW

BRACKET

INFEED

TABLE

CUTTER

GUARD

AUXILIARY FENCE

Some on-edge and other jointing operations require a

higher and/or Ionge rfence than you r tool provides. Select

apiece of smooth straight wood of the height and length

required for proper support and bolt it to the tool fence as

shown for these operations, 1/4-20 FLAT HEAD

SCREW COL

11 WARNING:

CUTTER GUARD. Provides protection over the

cutter head. It must always be in PlaCe and function-

ing properly. ....

Check the guard to make sure it is functioning

properly.

a. Position fence to right for maximum width of cut.

b. Pass a 1/4 in. thick piece of wood over cutterhead

between guard and fence,

Guard must return automatically to "rest position"

against fence when free of the wood,

tf guard does not return automatically, see Trouble

Shooting and Maintenance Sections.

CUTTER

GUARD

FENCE

INFEED TABLE

to know your jointer.planer

AALWAYS BE PARALLEL TO

or lrfac. _ of the w0rkpiece is

an iicati on that the OUTWARD

qFEED table is HiGH and must be

CROWNED CUT

or surface of the workpeice is

CONCAVE, it is an ind tcation that the OUTWARD

END of the fNFEED table is LOW and must be

adjusted.

Check the infeed table to determine the "out of

parallel" condition.

CONCAVE CUT

INFEED TABLE LOW

a, Insert apenciHn space at end of cutterhead to

hold cutterguard open.

b, Place astraightedge (large square or long level)

on outfeed table. First along one side than along

theother.

C. Raise infeed table until it touches straightedge.

d. Sight between tabte and straightedge to determine

high or!ow condition of end of infeed table.

= =ll

i l

]w,y

PENCIL ",

TABLE _ _-_" J__

it iseasier to adjust the infeed table while the Jointer

is setting on your workbench.

Do not turn the3ointer on its side or upside down to

adjust it.

WARNING: Attach a strip of wood to two blocks of

wood 10 in. high. Drive enough nails into thestrlp so

that Jointer does not ti p over while resting on blocks

causing possible injury,

a. Remove motor cord from outlet in switch box.

b. Remove Jointer pulley guard and V-belt.

c. Remove Jointertrom stand.

d. Place Jointer on blocks.

OF WOOD

YOUR WORK

BENCH

e. Insert apencil in space at end of cutterhead to

hold cutterguard open.

f. Wrap apiece of cardboard around cutterhead to

protect your fingers and the btades.., sec_ure

cardboard with a piece of tape.

CARDBOARD-

h. Loosenfourlockscrews 2or3turns withl/2in.

wrench.

LEVELING STUDS

LOCKSCREWS

VIEW LOOKING UP FOR PARTS IDENTIFICATION

Turning the LEVELING STUDS will RAISE or LOWER

the infeed table.

SCREWING in the studs will RAISE the table ....

UNSCREWING them wilt LOWER the table.

a. With a3/4 in. wrench turn leveling studs until

infeed table is parallel with straightedge.

b. While holding studs with wrench, TIGHTEN all

four LOCKSCREWS... tighten each screw a little

bit at atime until alt four screws are tight.

c. Recheck with straightedge to make sure infeed

table (in raised and lowered positions) is parallet

to ouffeed table.

j'ointer- pianer

be turned

=ched or bumped,

OFF"by striking

ehand.

n" is a key, when inserted in the

turned ON and OFF.

it is removed, the power cannot be turned ON.

THIS FEATURE tS INTENDED TO PREVENT

UNAUTHORIZED AND POSSIBLE HAZARDOUS

USE BY CHILDREN AND OTHERS.

a. Insert Key into switch,

NOTE: Key is made of yellow plastic,

b. TO turn machine on, insert finger under switch

lever and pull end Of switch out.

NOTE: Key is made of vellow plastic.

i i

c, To turn machine OFF PUSH lever in.

Never leave machine unattended until it has

come to a complete step.

d. TO lock switch in OFF position .. : hold switch IN

with onehand ... REMOVE key with other hand.

WARNING: FOR YOUR OWN SAFETY, ALWAYS

LOCK THE SWITCH "OFF" WHEN MACHINE IS

NOT IN USE... REMOVE KEY AND KEEP tT IN A

SAFE PLACE,., ALSO... IN THE EVENT OF A

POWER FAILURE (ALL OF YOUR LIGHTS GO

OUT) TURN SWITCH OFF... AND REMOVE THE

KEY. THIS WILL PREVENT THE MACHINE FROM

STARTING UP AGAIN WHENTHE POWER COMES

BACK ON. \

HOLD

PULL

MOTOR

CORD

e. Plug motor cord into outlet in switch box,

OUTLET

-- i i _1 ii ___

basic jointer-planer operation

POWER

CORD

WARNING: For your own safety, ALWAYS use the hold

down/push blocks when JOINTING wood that is

NARROWER than 3 tn.... or when PLANING wood that is

THINNER than 3 in.

Do not plane, joint or bevel wood shorter than 12 in.

Material this short is more difficult to control while being

cut. Small pieces of wood can tip over on the tables orinto

, , , i

the cutterhead and can be kicked back toward you.

For your own safety, never operate this tool with the fence

or guards removed.

For best results, take light cuts. For average planing,

jointing, or beveling, acut between t/32 and t/16 in. deep

will produce the best results.

FEEDING THE WORKPIECE

Hold the board firmly DOWN on both tables and AGAINST

the fence.., keep fingers close together.

Feed the boa rd at a continuous even rate of speed u ntil the

cut is made along the entire length of the board. Any

hesitation or stopping could cause a "step" to be cut on

the edge of the board which would cause the board to ride

up on the outfeed table resulting in a "crooked" edge on

the board.

i1,1 , iiil,,irl

JOINTING WOOD THAT IS WIDER THAN 3 IN.

As the RIGHT hand passe s over the cutterhead, remove

the LEFT hand... CONTINUE feeding while placing the

LEFT hand behind the RIGHT. Continue feeding in this

manner "hand over hand", until the entire length of the

board is cut. Pressure should be applied over the cutter-

head and outfeed table.

DO NOT FEED TOO FAST. A stow steady: rate of feed

produces a smooth accurate cut. Feeding too fast causes

a "rippled" cut,., makes it difficult to guide the workpiece ....

accurately and could be hazardous.

i i iiii iii1,1 i ,HI

PLANING WOOD THAT IS THICKER THAN 3 IN.

SUPPORT LONG WORKPIECES

basic jointer-planer operation

_ver 1

natu

AGAINST THE GRAIN, take very light cuts and feed

slowly,

ROTATION

WITH THE GRAIN

AGAINST THE GRAIN

USING THE HOLD DOWN!PUSH BLOCKS

ALWAYS use the hold down/push blocks when JOINTING

wood that is NARROWER than 3 in. or planing wood that is

thinner than 3 in. (as illustrated).

Grasp the hold down/push blocks firmly with the fingers

close together and wrapped around the handle. Position

them flat on top of workpiece, and push the workpiece

down against the table to provide aquality cut and

minimize the chance of akickback.

Hold-down pressure must also be sufficient to prevent

hold-down/push block sliding or slipping on the top face

of workpiece when advancing workpiece over cutter head.

Use a hand over hand motion of the hold down/push

blocks being careful to maintain control over the workpiece

at all times:

This means that once the workpiece has been fed past

cutter head onto outfeed table, one hold down/push block

must always maintain contact of work piece with ouffeed

table.

WARNING: If the HOLD DOWNIPUSH BLOCKS tend to

slip while feeding, Clean rubber surfacelmmediately with

sandpaper. _:

JOINTING WOOD NARROWER THAN 3"

PLANING WOOD THINNER THAN 3"

When planing wood 3/4 in. thick and NARROWER than

the hold down/push block, tilt the hotd down/push block

so that it clears the top of the cutterguard while feeding,

Never plane wood that is thin net than 1/2 in .... because it

sapt to spiitor shatter and th us has a greater ten dency to

kickback.: -"

BEVELING

Adjust the fence to the desired angle.., tighten fence and

guard lock knobs ......

For pieces of woo d 3" or wider hold the board firmlydown

on both tables and firmly against the fence (as illustrated)

with your hands on the side and top of the workpiece,..

keep finge_s close together.

NOTE: Removing only the corner on the edge of a board is

known as CHAMFERING while beveling is removing the

corner or the edge of the board down to the boards

surface.

Normally achamfer is made with one cut,., therefore, a

cut deeper than 1/16 in. may be made,

For pieces of wood less than 3" wide use hold down/push

blocks (as illustrated) on the side of the workpiece so you

can hotd the workpiece in toward the fence at all times as

well as down against the table top.

WARNING: DO NOT CONTACT THE CUTTING KNIVES

OR THE GUARD WITH THE PUSH BLOCKS.

BEVELING BOARD WIDER THAN 3 INCHES

CHAMFER BEVEL

BEVELING BOARD NARROWER THAN 3 iNCHES

NOTE: Rabbeting on a Jointer is considered to be a

dangerous operation because it requires removal of the

cutter guard and increases the potential of kickback

because of excessive depth of cut .....

NEVER ATTEMPTTO PERFORM A RABBETING OPERA-

TION ON THIS JOINTER. DO NOT OPERATE JOtNTER/

PLANER WITH CUTTERHEAD OR BELT GUARDS

REMOVED.

Rabbet cuts should be made on the Radial Saw or Tabte

Saw by making two cuts with the sawblade or by using the

Dado Head or Molding Head. Rabbet cuts can also be

made using the Shaper or Portable Router.:

, i

maintenance

RABBETCUT

::i• IHUlhUlN ........

BLOCK OF WOOD

REPLACING CUTTER BLADES

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE ADJUSTING, MAINTAINING, OR

LUBRICATING YOUR JOINTER-PLANER,

1. Remove be!t guard.

2. Position fence to right ,.. approximately 1/4 in,

beyond cutter blades.., lock it in place,

3. Lower infeed table all the way down,

4. Place block of wood 6-3/4 in, long between cutter-

guard and fence:

5. Hold cutterhead pulley firmly with one hand and

loosen iockscreWs in each wedge using a 5/32 in.

Setscrew wrench.

BLADE WEDGE

LIFTER LOCKSCREW

SCREW

5/32 IN.

SETSCREW

WRENCH

HOLD PULLEY

FIRMLY

CLOCKWISE

LOOSEN

FENCE NOT SHOWN

FOR PICTURE CLARITY

6. While holding Cutterhead pulley firmly with one hand,

gentlypry up each Wedge using a screwdriver . .

remove wedges and blades.

SMALL SCREWDRIVER

7. Remove the six lifter screws. (Two under each blade.)

8. Clean cutterhead, weoges and screws thoroughly with

Craftsman Gum and Pitch Remover. also remove the

oil from new blades.

9. Replace the six lifter screws and screw them in all the

way, but do not tighten. Mark each slot 1,2, and 3. This

witl help you in setting the blades.

CUTTER HEAD '

SETSCREW

MARK SLOTS

1, 2 AND 3X

!/8 IN. SETSCREV

WRENCH

I/8 IN, SETSCREW WRENCH

10. Insert a blade in slot marked I.,. so it projects t/16 in.

beyond end of the cutterhead,

11. "Insert a wedge next to blade so the flat side of the

wedge is against the bla(_e. Push wedge in manually

-do not install two locking setscrews at this time."

!2, Place head of square on outfeed table. Loosen lifter

screws to raise blade until it just touches square and

slightly raises it. Gently turn cutter head back and

forth with the pulley while raising blade. The blades

should be adjusted just slightly above the cutfeed

table, by approximately .003 in. (thickness of an

average piece of paper).

NOTE: Sears has a knife setting gauge for this purpose.

Cat. #9-2647

HEAD OF

SQUARE ........

OUTFEED_

LIFTER SCREW

...... ii ,lllllr,i!iN,llll ii iii i

13. "Now install both locking setscrews and tighten (with

the 5/32" setscrew wrench) alternately a little at atime.

Tighten both screws securely. Recheck the blade to

make sure it did not change position."

14. Install other two blades the same way.

INFEE

INSTALLING CUTTER GUARD SPRING FLAT WASHER _zSPRtNG

t. Remove cotter pin from pivot pin in cutter guard and _"-'-_ !_ SUPPORT

remove guard (located u_derneath infeed table). _LOCK _-_ 7"_PLATE

Spring must appear as in sketch from underside of infeed WASHE R_"_.._ /

table, it will not perform properly if nsta ed upside down. _ _ BUSHING

SCREW

VIEW LOOKING UP

maintenance

2. Position guard as shown with;PIVOT PIN above hole

in infeedtable.

3, Align SLOT in pin With TANG in spring, and press

down.

4i Replace cotter pin.

FENCE

IN PLACE

TANG OF SPRING

IN CENTER OF

HOLE

CUTTER

GUARD

'1 iii ii i

PIVOT PIN

5. RAISE end of FENCE, rotate guard COUNTER clock-

wise only enough to CLEAR fence,

6. LOWER fence and tighten both knobs.

\LI FT

COUNTER

CLOCKWISE

FENCE

= =

The normal position of guard (at REST) when fence is

stationed at MAXIMUM WIDTH OF CUT. is shown as

"position "A". NEVER ROTATE GUARD BEYOND POSI-

TION "B" BECAUSE THIS WOULD EXERT EXCESSIVE

TENSION ON SPRING WHICH COULD WEAKEN OR

BREAK IT.

Check operation of GUARD and SPRING.

1. With fence in MAXIMUM WIDTH OF CUT position,

pass apiece of 1/4 in, thick wood on edge (jointing

position) over cutterhead.

2. The guard should return automatically to its REST

position against the fence when free of the wood.

3. If guard does not return to its REST position, remove

cotter pin from pivot pin and remove guard. Check

pivot pin and hole.., make sure there are no burrs,

rust, or other foreign matter.

4. Apply a few drops of SAE No. 20 or No, 3Oengine oil to

pivot pin.

5. Replace guard and cotter pin.

POSIT1 ON °'B"i,J /

If guard still does not return to its REST position consult

your local Sears Retail Store before using the jointer- :

planer.

[

MAX.

WIDTH OF

CUT !

22 - i:

SHARPENING CUTTER BLADES

The blades can be honed individually with an ordinary

oilstone.

Make sure your oilstone is not worn in the center. It must

be fiat.

Be sure to remove the burr on the fiat side.

If the blades are nicked, they must be replaced or

reground. They can be regrounded several times until

they become 9/16 in. wide. Never install reground blades

less than 9/16 in. wide or unbalanced blades.

Have your knives reground by someone who is competent.

Look in the "Yellow Pages" of your telephone directory...

see "Sharpening Services". 11116 IN,

NEW BLADE

........................................ i1=rll i=

general maintenance

Keep your jointer_planer clean. Put a carton or some kind

of a container underneath your jointer-planer to catch the

chips. The container should reach above the top of the

motor.

Do not allow pitch to accumulate on the tables, the fence.

the cutter g uard, the cutter head or the knives. Clean them

with Craftsman Gum and Pitch Remover.

Apply a thin coat of paste type wax to the tables and fence

so that the wood slides easily while feeding.

Do not atlow chips to accumulate on the underside of the

jointer-planer.

Frequently biow out any dust that may accumulate inside

the motor.

If power cord iis worn or cut, or damaged in any way, have

it replaced immediately:

lubricaUon

The BALL BEARINGS in this machine are packed with

grease at the factory. They require no further lubrication.

The following parts should be oiled occasionally with SAE

No. 20 or No. 30 engine oil.

1. Dovetail spacer and dovetail slide.

2. Elevating screw (first clean with Craftsman Gum and

Pitch Remover).

DOVETAIL

SPACER AND SLIDE

ELEVATING SCREW '

VIEW LOOKING UP FOR

PARTS IDENTIFICATION

MOTOR MAINTENANCE AND LUBRICATION

1. The bearings, in both end shields of the motor, have

been lubricated at the factory with €orrect lubricant.

NO Other part of the motor requires lubrication.

2_Re-lubricate motor bearings in accordance with the

instrgctions on the nameplate. Be sure to wipe off dirt

or grit if present around oil hole caps to prevent any

possibility of foreign material contaminating the oil

wicks that supply the bearings with oil. Use agood

-grade of medium weight mineral oil, such as automo-

bile engine noii, SAE 20.

3. If disassembly of the motor is necessary, it should be

returned to your neareast Sears retail or mail-order

store in order to prevent voiding the guarantee.

NOTE: The speed of this motor cannot be regulated or

changed.

4. Every effort shou Id be made to prevent foreign material

from entering the motor. When operated under cond|-

tions likely to permit accumulations of dust, dirt, or

waste within the motor, a visual inspection should be

made at frequent intervals. Accumulations of dry dust

car'; usually be blown out successfully.

NOTE: Motors used on wood-working tools are

particularly susceptible to the accumulation of sawdust

and wood chips and should be blown out or

"vacuumed" frequently to prevent interference with

normal motor ventilation and proper operation of the

centrifugally-operated starting switch.

trouble shooting

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM

POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING YOUR JOINTERPLANER.

TROUBLE SHOOTING CHART

TROUBLE PROBABLE CAUSE REMEDY

1. Defective On-Off switch. 1. Replace defective parts before using machine again.

Defective switch cord.

Defective switch box

receptacle.

-2. Motor protector open (only 2, Consult Sears Service. Any attempt to repair this motor

- : if your motor is equipped may create a HAZARD unless repair is done by a

.... : wi:th an ovedoad protector), qualified service technician. Repair service ls available

table after passing over ,below surface of outfeed table.

Ripples on planed 1, One blade set higher than 1. Re-adjust btades, see Maintenance section.

surface, Iother.

2. Feeding wood too fast. 2. Feed wood slower.

Planed surface not Infeed table out of adjustment. Re-adjust infeed table, see Getting To Know your Jointer'

straight. , Planer section.

Excessive gouging at Blades set too h gh above Reset blades, see Maintenance section.

end of cut. outfeed table.

90° and 45° cuts 1. Fence stops not adjusted 1. Re-adjust fence stops, see Getting To Know your

inaccurate, properly. Jointer Planer section+

2. Fence slide bracket not 2. Re-adjust slide bracket, see Getting To Know your

• even with table. Jointer Planer section.

InrOad table loose, l lDovetail spacer requires 1. Tighten screw, key lO, see fig, 3 Parts List.

,adjustment, i

2. Female dovetail loose from! 2. Tighten screws, key 17, see fig. 3, Parts List.

.... t table. : i ...........

Cutter guard does not 1. Return spring brokeni or 1 Replace spring immediately. See Maintenance section.

function properly, spring has been weakened_ : :

.... " _ .... _ 2. improper assembly of 2. See Maintenance section.

Ispring or guard mounting.

TROUBLE SHOOTING -- MOTOR .......

NOTE: Motors used on wood-working tools are particularly susceptible to the accumulation

of Sawdust and wood chips and should be blown out or "vacuumed" frequentiy to prevent =

interference with normal motor ventilation and proper operation of the centrifugally-

operated starting switch. ,'

TROUBLE PROBABLE CAUSE REMEDY

Excessive noise. 1, Motor,

Motor fails to develop

full power, NOTE:

LOW VOLTAGE: (Power

output of motor

decreases rapidly with

decrease in voffage at

motor terminals. For

example, a reduction of

10% in voltage causes a

reduction of 19% in

maximum power output

of which the motor is

capable, and a reduction

of 20% in voltage causes

a reduction of 36% in

maximum power output.)

Motor starts slowly

or fails to come up

ito full speed,

Motor overheats.

Starting switch in motor

wilt not operate.

Motor stalls (resulting

in blown fuses or

tripped circuit breakers),

Frequent opening of

fuses or circuit

breakers.

1. Circuit overloaded with

lights, appliances and other

motors.

2r Undersize wires or circuit

too long.

3. General overloading of

power company facilities.

!. Low voltage will not trip

relay,

2. Windings burned outor

open.

3. Starting relay not operating.

!. Motor overloaded.

2. Improper cooling. (Air

circulation restricted

through motor due to

sawdust, accumulating

inside of motor).

1. Burned switch contacts

(due to extended hold-in

periods caused by low line

voltage, etc.).

2. Shorted capacitor.

3. Loose =or broken

connections.

1. Starting switch not

operating.

2. Voltage too tow to permit:

motor to reach operating

speed!

3. Fuses or circuit breakers

do not have sufficient

capacity.

1. Motor overloaded.

2. Fuses or circuit breakers

do not have sufficient

capacity.

3, Startring switch not

operating (motor does not

reach speed).

1, Have motor checked by qualified service technician.

Repair service is available at your nearest Sears store.

t. Do not use Other appliances or motors on same circuit

when using the jointer.

2. Increase wire sizes, or reduce length of wiring. See

"Motor Specifications and Electrical Requirements"

section.

3. Request a voltage check from the power company.

1. Request voltage check from the power company.

2. Have motor repaired or replaced.

3. Have relay replaced.

1. Feed work slower into blade.

2. Clean out sawdust to provide normal air circulation

through motor. See "Maintenance and Lubrication"

section.

1. Have switch replaced and request a voltage check

from the power company.

2. Have capacitor tested and replace if defective.

3. Have wiring checked and repaired.

1. Have switch replaced.

2. Request voltage check from the power company.

3. Install proper size fuses or circuit breakers.

1. Feed work slower.

2. install proper size fuses or circuit breakers.

3. Have switch replaced.

repair paris

Li.

0 z

2:."i

"J I_

_z_,.

m _

-n

"o d

o -0 co

nt .-_"

_0_ ^_

•_ _ 0._- _

x O- _ l'_? O_

oE _.oxo

._r -- _ 0_

mm0 "r nO 00 _ _0 _0 m 0

_ 0 o_ _ o

zo_ ____o__

-- _ "0 "- 0 "r

•0 0 ,- o F_"

_r_ 0 ....... _o!_ _ , _.m -- m _ x × •

_00_ r_ _0- - _0 0 00_ 0 0

c o

_>. oO

z Eb5

repair parts

CRAFTSMAN 6-1/8 INCH JOINTER-PLANER MODEL 113.206933

FIGURE 2

FIGURE 2 -- LEGS PARTS LiST

Key

No.

Part

No. Description

67033 Stiffener, End

60314 • Screw, Truss Hd. 1/4-20 x 5/8

STD551225 e*Lockwasher, 1/4 External

STD541025 e'Nut, Hex 1/4-20

67032 Stiffener, Side

62614 Leg

62204 •Clip, Cord

67034 Support, Motor

STD541250 e'Nut, Hex Hd. 1/2-13

803835 DFoot, Leveling

67035 Bag of Loose Parts (Not Iltus.)

HARDWARE FOR MOUNTING TOOL AND MOTOR

-- STD532507 e'Bolt, Carriage 5/16-18 x 3/4

STD551231 e*Lockwasher, 5/16 External

STD551031 s'Washer, 1!/32 x 11/16 x 1/t6

-STD523120 t'Screw, Hex Hd= 5/16-16 x 2

:e'Nut, Hex 5116-!8

oSupptied in Loose Parts Bag 67035

*Standard Hardware Item - May be Purchased Locally.

CRAFTSMAN 6-1/8 INCH JOINTER-PLANER MODEL 113.206933

1 \

FIGURE 3

21 22

\\\ 2o

Key Part

No. No.

nl ,,i,n i ,n

1 STD561210

2 67015

3 67014

4 STD511107

5 STD5512t0

6 STD551010

738779

8 67011

9 67012

t0 STD522505

11 STD55tO25

12 21812

FIGURE 3 -- INFEED TABLE PARTS LIST

Description

iinl

*Pin, Cotter, 1/8x 1

Guard

Tabfe (with Name Plate)

*Screw Pan Hd. 10-32 x 7/8

*Lockwasher No. 10

*Washer, No. 10

Spring. Guard

Plate Support

Bushing

*Screw, Cap, 1/4-20 x !/2,

Hex Hd.

*Washer, Plain, 17/64

Plate, Tension=

Key Part

No. No.

13 21422

14 21219

15 21218

16 STD551131

17 i21635

18 STD523112

STD551031

21204

STD54!025

STD551125

STD5225t0

Description

Spacer, Dovetail

Dovetail, Male

Dovetail, Female

*Lockwasher, 5/16

Screw, Spl.

*Screw, Cap, 5/16-18 x t_1/4

Hex Hd.

*Washer, 5/I6

Linkage Assembly

*Nut, Hex,, 1/4-20

"Lockwasher, 1/4

*Screw, Cap, 1/4-20 x 1, Hex Hd.

*Standard Hardware Item -- May Be Purchased Locally.

CRAFTSMAN 6-1/8 INCH JOINTER-PLANER MODEL 113.206933

5 6 7

17 /

16 15

/10

\\11

FIGURE 4

FIGURE 4 -- 21013 FENCE ASSEMBLY PARTS LIST

Key Part

No. INo.

21013

1 21440

2 21430

STD522512

21232

i21736

STD551010

7 STD510802

8 102817

Description

921229

inc KeyNo's 10&11

I :,, . •

Plunger Assembly

.Pin Assembly, Stop

Screw, Hex Hd. 1/4-20 x !-t/4

Plate, Fence End

Scale, Fence Tilt

*Washer, Ptain, 13/64

*Screw, Mach., No. 8-32 x 1/4,

Bind Hd., Slotted

Screw, Se[, 1/4-20 x 1/2", Full

Dog Pt., Slotted

, Body, Fence

Key Part

No. No.

10 STD551210

11 STD511102

12 67009

13 STD533725

14 21738

15 STD551037

16 47624

17 62331

Description

,,, ,,,

*Lockwasher, Ext. #10

*Screw, Mach,, No. 10-32 x t/4,

Pn Hd., Slotted

Guard, Cutter

"Bolt, Carriage, 3/8-t6 x 2-1/2

Round Head

Retainer, Bolt

*Washer, 13/32 x13/16 x !/16

Spacer

Knob Assembly, Lock

*Standard Hardware Item -- May BePurchased Locally.

FIGURE 5 -- ON/OFF POWER OUTLET 60381

FIGURE 5

Key Part

No. No.

-- 60381

160375

260380

3 60256

Description

cOn/Off Power Outlet Complete

Cord, Molded

Housing, Switch

Key, Switch

60374 'Switch, Locking

60376 Cover Switch

6448007 i Screw, PanHd, No.6x3/4

eDoes Not Include Key No. 3 Order Separately If required.

CRAFTSMAN 6-1/8 iNCH JOINTER-PLANER MODEL 113.206933

NOTE:

ANY ATTEMPT TO REPAIR THIS MOTOR

MAY CREATE A HAZARD UNLESS

REPAIR iS DONE BY QUALIFIED

SERVICE TECHNICIAN.

REPAIR SERVICE IS AVAILABLE

AT YOUR NEAREST SEARS STORE,

FIGURE 6 -- 67094 MOTOR PARTS LIST

Key Part

No. No.

1 60306

2 64088

3 64258

Description

Screw, 8_32 x 3/8, Thread

Cutting, Slotted, Serrated Hd.

Cover, Terminal

Cord with Plug

........ • ........................................................... ,,,,i,i,,

MOTOR CONNECTIONS

WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT

PLUG TO POWER SOURCE OUTLET UNTIL ALL

ASSEMBLY STEPS ARE COMPLETED.

1. Open motor connector box cover located on left end

of motor (viewed from rear of saw) using a flat b_ade

screwdriver,

2. Remove GREEN SCREW and Iockwasher and insert

screw through round metal terminal on the end of the

GREEN wire of power cord with Iockwasher between

terminal and motor frame. (See [llus_)

3. Reinsert GREEN SCREW in the threaded hole, Tighten

securely.

4. Insert terminal end of WHITE wire on spade terminal

marked T4 on the motor, Push terminal firmly until

seated.

5. Insert terminal end of BLACK wire on spade termina_

marked T1 on the motor. Push terminal firmly until

seated.

6. Close motor connector box being sure that power

cord is seated in the largest strain relief groove, and

tighten box cover screws.

TERMINAL

GREEN

INTERNAL

LOCKWASHER

GREEN WtRE

_TO GREEN SCREW

STRAIN RELIEF

)VE

WHITE WIRE TO

TERMINAL T4

IIIHI,, _iH ........................... ii

RECOMMENDED ACCESSORIES

ITEM CAT. NO.

Steel Legs ................................. 9-22245

FloOr Stand .............................. 9-22216

Cutter Blades .............................. 9-2293

Power Too! Know-how Handbooks

Radial Saw .............................. 9-291;

Table Saw ................................. 9o2918

Knife Setting Gauge ........................ 9-2647

Chip Collector ............................ 9-29977

The above recommended accessories are current and

were available at the time this manual was printed_

SL _,AIR,,

SERVICE

MODEL NO.

11 3.206933

JOINTERiPLANER WITH

LEGS AND MOTOR

HOW TO ORDER

REPAIR PARTS

Part No. 67096

6-1/8 iNCH JOINTER-PLANER

Now that you have purchased your jointer-planer, should a

need ever exist for repair parts or service, simply contact

any Sears Service Center and most Sears, Roebuck and Co,

stores. Be sure to provide all pertinent facts when you call

or visit.

The model number of your 6-1/8 inch jointer-planer wil! be

found on a plate attached to your base.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

PART NUMBER PART DESCRIPTION

MODEL NUMBER NAME OF ITEM

113.206933 6-1/8 INCH JOtNTER-PLANER

All parts listed may be ordered from any Sears Service

Center and most Sears stores. If the parts you need are not

stocked locally, your order wilt be electronically transmitted

to a Sears Repair Parts Distribution Center for handling.

Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.

Form No. SP4939-1 Printed in U.S.A. 11/

Craftsman 113206933 User Manual 61/8 INCH JOINTER PLANER Manuals And Guides L0709234

CRAFTSMAN Jointer/Planer Manual L0709234 CRAFTSMAN Jointer/Planer Owner's Manual, CRAFTSMAN Jointer/Planer installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation