Craftsman 113213150 User Manual DRILL PRESS Manuals And Guides L0905102

CRAFTSMAN Drill Press Manual L0905102 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

User Manual: Craftsman 113213150 113213150 CRAFTSMAN DRILL PRESS - Manuals and Guides View the owners manual for your CRAFTSMAN DRILL PRESS #113213150. Home:Tool Parts:Craftsman Parts:Craftsman DRILL PRESS Manual

Open the PDF directly: View PDF .
Page Count: 36

Download
Open PDF In Browser	View PDF

Save ThisManual \
For FutureReference

MODEL NO.
143,213150

DRILL PRESS WITH
MAXIMUM
DEVELOPED
I HP MOTOR

Serial
Number
Model and serial number
may be found at the rear of
the head.
You should record both
model and serial number in
a safe place for future use.

CRRFrSMRN

MOTORIZED

CAUTION:

t5-|NCH
FLOOR MODEL DRILL PRESS

READ ALL
INSTRUCTIONS
CAREFULLY

Sold
Part No. SP5187

by SEARS, ROEBUCK

• assembly
• operating
• repair parts

AND

CO.,

Chicago,

IL 60684

U.S.A.
Printed

in Taiwan

FULL ONEYEAR

WARRANTY

ON CRAFTSMAN

DRILL PRESS

If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect
in material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684

GENERAL SAFETY iNSTRUCTiONS
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
labels affixed to the tool. Learn its application and
limitations as well as the specific potential hazards
peculiar to this tool.
2. GROUND ALL TOOLS
This tool is equipped with an approved 3-conductor
cord and a 3-prong grounding type plug to fit the
proper grounding type receptacle. The green conductor in the cord is the grounding wire. Never
connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE
In working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and
adjusting wrenches are removed from toot before
turning it on
5. KEEP WORK AREA CLEAN
Cluttered areas and benches inviteaccidents. Floor
must not be slippery due to wax or sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or

7. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area.
8. MAKE WORKSHOP CHILD-PROOF

9.
10.

11,

12.

With padlocks, master switches, by removing starter keys. or storing tools where children can't get
them.
DON'T FORCE TOOL
It will do the job better and safer at the rate for
which it was designed.
USE RIGHTTOOL
Don't force tools or attachment to do a job it was
not designed for.
WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties, or
jewelry (rings, wrist watches) to get caught in moving parts. NDNSLIP footwear is recommended.
Wear protective hair covering to contain long hair,
Roll long sleeves above the elbow.
USE SAFETYGOGGLES (HEAD PROTECTION)
Wear safety goggles (must comply with ANSI

FOR POWER TOOLS

787.1) at all times. Everyday eyeglasses are not
safety glasses. They only have impact resistant
lenses. Also. use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs)
during extended periods of operation.
13. SECURE WORK
Use clamps or a vise to hold work when practical.
It frees both hands to operate tool,
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Followinstructionsfor lubricatingand
changing accessories.
16. DISCONNECT TOOLS
Before servicing; when changing accessories suc
as blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plugging in.
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended accessories. Follow the instructionsthat accompany
ihe accessories. The use of improper accessories
may cause hazards.
19. NEVER STAND ON TOOL OR ITS STAND
Serious injury could occur if the tool is tipped or if
the cutting tool is accidentally contacted, Do not
store materials above or near the tool such that it
is necessary to stand on the tool or its stand to
reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool a guard or other part
that is damaged should be carefully checked to
ensure that it will operate properly and perform its
intended function Check for alignment of moving
parts, binding or moving parts, breakage of parts,
mounting, and any other conditions th
its operation. A guard or other part tha
should be properly repaired or replac
21, DIRECTION OF FEED
Feed work into a blade or cutter agai
tion of rotation of the blade or cutter only.
22. NEVER LEAVETOOL RUNNING UNATTENDEC
Turn power off. Don't leave tool until it comes to a
corn plete stop.

additional

safety

instruct

ions for drill presses

=
C

d. To prevent the workpiece from being
torn from your hands, spinning of the
tool. shattering the tool or being thrown,
always properly support your work so
it won't shift or bind on the tool:

VsARNING: FOR YOUR OWN SAFETY, DO NOT
E YOUR DRILL PRESS UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE iNSTRUCTIONS . . . AND UNTIL YOU
HAVE READ AND UNDERSTAND THE FOLLOWING:
1. General

Safety Instructions

2. Getting
3. Basic

for Power Tools.

to Know Your Drill Press
Drill Press

Operation

........

.............

2
17
23

4. Adjustments

..........................

5. Maintenance

..........................

6. Stability
of Drill Press
If there is any tendency of the drill press to tilt or
move during any use, bolt it to the floor or a flat
piece of !/S' exterior
plywood large enough to
stabilize the drill press. Bolt the plywood to the
underside of the Base, so it extends at least to
both sides. Make sure the plywood won't trip the
operator. Do not use pressed wood panelsthey can break unexpectedly.
If the workpiece is too large to easily support
one hand, provide an auxiliary support.

with

7. Location
Use the drill press in a well lit area and on a level
surface clean and smooth enough to reduce the
risk of trips, slips, or falls. Use it where neither the
operator nor a casual observer is forced to stand
in line with a potential kickback.
8.

Kickback
A kickback occurs when the workpiece is suddenly
thrown in the OPPOSITE
direction to the DIRECTION OF FEED: THIS CAN CAUSE SERIOUS INJURY. Kickbacks are most commonly caused by
use of accessories NOT recommended
for this tool.

9. Protection: Eyes, Hands, Face, Ears and Body
WARNING:
TO AVOID BEING PULLED
INTO
THE SPINNING TOOL -1. Do NOT wear:
----2. Do

gloves
necktie
loose clothing
jewelry
tie back long hair

a. If any part of your drill press is missing, malfunctioning, has been damaged or broken,.,
such
as the motor switch, or other operating control,
a safety device or the power cord , . . cease
operating immediately
until the particular part
is properly repaired or replaced.
b. Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece
should unexpectedly
shift or
your hand should slip.
c. Toavoid
injury from parts thrown by the spring,
follow instructions exactly as given and shown
in adjusting spring tension of quill.

---

Always position BACKUP MATERIAL (use
beneath the workpiece)
to contact the left
side of the column.
Whenever
possible,
position the WORKPIECE to contact the left side of the column-if
it is too short or the table is tilted,
clamp solidly to the table. Use table slots
or clamping ledge around the outside edge
of the table.
When using a drill press VICE. always fasten it to the table.
Never do any work "FREEHAND"
(handholding workpiece rather than supporting it
on the table), except when polishing.
Securely lock Head and Support to Column,
Table Arm to support, and Table to Table
Arm before operating drill press.
Never move the Head or Table while the
tool is running.
Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration,
If a workpiece
overhangs
the table such
that it will fall or tip if not held, clamp it to
the table or provide auxiliary support.
Use fixtures
for unusual
operations
to
adequately
hold, guide and position workpiece.
Use the SPINDLE SPEED recommended
for the specific operation
and workpiece
material--check
the label inside the Belt
Guard for drilling information;
for accessories, refer to the instructions
provided
with the accessories.

f. Never climb on the drill press Table, it
could break or pull the entire drill press
down on you.
g. Turn the motor Switch Off and put away
the Switch Key when leaving the drill
press.
h. To avoid injury from thrown work or tool
contact, do NOT perform layout, assembly, or setup work on the table while
the cutting tool is rotating.
10. Use only accessories designed for this
drill press to avoid serious injury from
thrown broken parts or work pieces.
a. Holesaws must NEVER be operated on
this drill press at a speed greater than
400 RPM.

-_
o_

Drum sanders must NEVER be operated on
this dr I press at a speed greater than 1800

13. Think Safety. Safety is a combination of operator
common sense and a ertness at a t mes when the

RPM.
c. Do not install or use any drill that exceeds 7 in
length or extends 6' be ow the chuck jaws They
can suddenly bend outward or break
d. Do not use wire wheels, router bits, shaper cutters, circle (fly) cutters or rotary planers on this
drill press.
I1. Note and Follow the Safety Warnings and Instructions that Appear on the Panel on the
Right Side of the Head:

KnOw This

Tool

Read and Understand

Use Recommended

o= Always
_
with

_
ANSI

Drill Speed--See

short
•

clamp

work

to contact

operating

the

arm to support,
or loose

to table it it is too
column

when in

position.

this Machine,

Chart Inside Pulley Cover.

FOR
OWN
that YOUR
comply
m Securely SAFETY:
lock head and

S_tFet y goggles
Z87.1.

m DO not wear
gloves,
necktie
c!Othtng,
T_e back long hair,
• Securely

Owner'S Manual before Using

operating
u Use only

and table

drill press.
recommended

dril! press is being used.
WARNING: DO NOT ALLOW FAMILIARITY (GAINED
FROM FREQUENT USE OF YOUR DRILL PRESS)
TO BECOME COMMONPLACE.
ALWAYS
REMEMBER THAT A CARELESS FRACTION OF A
SECOND IS SUFFICIENT TO INFLICT SEVERE
INJURY.
The operations of any power tool can result in foreign
objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles comply with ANSI Z87.! (shown on Package) before commencing power tool operation. Safety Goggles are
available at Sears retail or catalog stores.

support
to arm

to column.
before

accessories.
. _

/f_p_

12. This Drill Press has 12 speeds as listed below:
250 RPM
340 RPM
390 RPM
510 RPM
600 RPM
650 RPM

990
1550
1620
1900
2620
3100

RPM
RPM
RPM
RPM
RPM
RPM

See inside of belt guard for specific placement of
belt on pulleys.

¸¸¸4¸¸¸¸¸

gmossary of terms
1. Workpiece
The item on which the cutting operations is being
performed.
2. Drill
The cutting tool used in the drill press to make holes
in a workpiece,

4. Revolution Per Minute (R.P.M.)
The number of turns completed by a spinning object
in one minute.
5. Spindle Speed
The RPM of the spindle.
!t,,..

==E

3. Backup Material
A piece of wood placed between the workpiece and
table ....
it prevents wood in the workpiece from
splintering when the drill passes through the backside of the workpiece .... also prevents drilling into
the table top.

_._o

oE
c

table of contents
Page

Page
General Safety Instructions for Power Tools ......
Additional Safety Instructions for Drill Presses ....
Glossary of Terms ..........................
Table of Contents ...........................
Motor Specifications and Electrical
Requirements ..............................
Unpacking and Checking Contents .............
Table of Loose Parts ........................

2
3
5
5

cation and Function of Controls ..............
sembly ................................
Assembly of Column and Table Hardware..,
Installing the Table .....................
Installing the Head .....................
Mounting Motor ........................
Installing Motor Pulley ...................
Tensioning Belt ........................
Installing Belt Guard Knob ...............
Motor Connections .....................
Installing Feed Handles .................
Installing the Chuck .....................
Installing Light Bulb .....................

9
10
10
11
11
12
12
12
13
14
14
14
16

6
7
8

Adjusting the Table Square to Head .......
Bevel Scale ...........................
Getting to Know Your Drill Press ..............
On-Off Switch .........................
Drilling to a Specific Depth ...............
Locking Chuck Desired Depth ............
Removing Chuck and Arbor ..............
Re-Installing The Chuck and Arbor ...........
Basic Drill Press Operation ..................
Installing Drills .........................
Positioning Table and Workpiece ..........
Tilting Table ...........................
Hole Location .........................
Feeding ..............................
Adjustments ..............................
Quill Return Spring .....................
Maintenance ..............................
Lubrication ...............................
Recommended Accessories ..................
Trouble Shooting ..........................
Repair Parts ..............................

16
16
17
19
20
20
21
22
23
23
24
25
25
25
25
25
26
26
26
27
28

motor specfflcat=ons and electrmca requirements
m

MOTOR SPECIFICATOONS

This power tool is equipped with a 3-conductor
cord
and grounding
type plug. approved
by Underwriters'
Laboratories
and the Canadian Standards Association,
The ground conductor
has a green jacket and is attached to the tool housing at one end and to the ground
prong in the attachment
plug at the other end.

This drill press is designed to use a 1725 RPM motor
only. Do not use any motor that runs faster than 1725
RPM It is wired for operation on 110-120 volts, 60 Hz.
alternating current.
WARNING: TO AVOID INJURY FROM UNEXPECTED STARTUP, DO NOT USE BLOWER OR
WASHING MACHINE MOTORS OR ANY MOTOR
WITH AN AUTOMATIC RESET OVERLOAD PROTECTOR.

This plug requares a mating 3-conductor
outlet as shown.

grounded

type

If the outlet you are planning to use for this power tool
is of the two prong type. DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER. Use
an adapter as shown and always connect the grounding
lug to known ground.

CONNECTING TO POWER
SOURCE OUTLET
This machine must be grounded while in use to protect
the operator from electric shock.

It is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet,

Plug power cord into a 110-120V properly grounded
type outlet protected by a 15-amp. dual element time
delay or Circuit breaker.
NOT ALL OUTLETS ARE PROPERLY
GROUNDED.
IF YOU ARE NOT SURE THAT YOUR OUTLET, AS
PICTURED
BELOW,
IS PROPERLY
GROUNDED,
HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN.

An adapter as shown below _savailable for connecting
plugs to 2-prong receptacles.
WARNING: THE GREEN GROUNDING LUG EXTENDING FROM THE ADAPTER MUST BE CONNECTED TO A PERMANENT GROUND SUCH AS
TO A PROPERLY GROUNDED OUTLET BOX.

WARNING: TO AVOID ELECTRIC SHOCK, DO NOT
TOUCH
THE METAL
PRONGS
ON THE PLUG.
WHEN INSTALLING
OR REMOVING
THE PLUG TO
OR FROM THE OUTLET.

GROUNDING
SCREW

WARNING: FAILURE TO PROPERLY GROUND THIS
POWER TOOL CAN CAUSE ELECTRICUTION
OR
SERIOUS SHOCK, PARTICULARLY
WHEN USED IN
DAMP LOCATIONS,
OR NEAR METAL PLUMBING.
IF SHOCKED,
YOUR REACTION
COULD CAUSE
YOUR HANDS TO HIT THE CUTTING TOOL.

LUG

3-pLPRONG"_

MAKE SURE THIS IS

IF POWER CORD ISWORN
OR CUT, OR DAMAGED
IN ANY WAY, HAVE IT REPLACED
IMMEDIATELY
TO AVOID SHOCK OR FIRE HAZARD.
RECEPTACLE
3-PRONG
PLUG

ADAPTER

NOTE: The adapter illustrated is for use only if you
already have a properly grounded 2-prong receptacle.
Adapter is not allowed in Canada by the Canadian Electrical Code.

The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent overheating and motor burn-out, use the table below to
determine the minimum wire size (A.W.G.) extension
cord, Use only 3 wire extension cords which have 3prong grounding type plugs and 3-pole receptacles
which accept the tools plug.

GROUNDING

PRONG
ALWAYS USE A
PROPERLY GROUNDED
OUTLET

Your unit is for use on !20 volts. It has a plug that looks
like the one above.

Extension Cord Length
0-25 Feet
26-50 Feet
51-100 Feet
6

Wire Size A.W.G,
16
14
12

unpacking and checking contents
TABLE

WARNING: TO AVOID INJURY FROM UNEXpECTED STARTING OR ELECTRICAL SHOCK, DO
_OT PLUG THE POWER CORD INTO A SOURCE
OF POWER. THIS CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE
DRILL PRESS.
Model 113.2!3150
one box.

Item
A
B
C
D
E
F
G
H

Drill Press is shipped complete in

1. Unpacking and Checking Contents
a. Separate all "loose parts" from packaging materials and check each item with "Table of Loose
Parts" to make sure all items are accounted for,
before discarding any packing material. Some
loose parts are contained inside the belt guard,
Open the belt guard cover to find them.
WARNING: IF ANY PARTS ARE MISSING, DO NOT
ATTEMPT TO ASSEMBLE DRILL PRESS, PLUG IN
THE POWER CORD, OR TURN THE SWITCH ON
UNTIL THE MISSING PARTS ARE OBTAINED AND
ARE INSTALLED CORRECTLY.

OF LOOSE

PARTS

Description
Table ..............................
Column Support Asm ..................
Owner's Manual ......................
Motor ..............................
Bag of Loose Parts ...................
Base ...............................
Head Asm ...........................
Box of Loose Parts ...................

2. Remove the protective oil that is applied to the
table and column. Use any ordinary household type
grease and spot remover.
WARNING: TO AVOID FIRE OR TOXIC REACTION, NEVER USE GASOLINE, NAPTHA OR
SIMILAR HIGHLY VOLATILE SOLVENTS.

o'}o

3. Apply a coat of paste wax to the table and column
to prevent rust. Wipe all parts thoroughly with a clean
! dry cloth.

Qty.
1
1
1
1
2
1
1
1

List of Loose Parts in Bag 507886
Item
Description
A Feed Handle ........................
B Key Drift .................
C Wrench Hex "L" 3mm .................
D Wrench Hex "L" 5mm .................
E Crank ..............................
F Clamp Column ......................

Qty.
3
1
1
1
1
1

t
B

List of Loose Parts in Box 507887
Item
Description
G Chuck ..............................
H Chuck Key ..........................

Qty.
1

List of Loose Parts in Bag 507888
item
Description
I Screw Hex HD. MIO x 1.5-40 ...........
J Key-Switch ..........................
K Knob (Guard) ........................
L Screw Pan HD. M5 x 0.8-12 ............

Qty.
4
1
1
1

"-,.-...lb.

L
K

List of Loose Parts in Bag 507889
item
Description
M Idler Pulley Assembly .................
N Pulley-Motor .........................
O Belt "V" 3/8 x 24 .....................
P Belt "V" 3/8 x 26 .....................
Q Screw-Hex HD. M8 x 1.25-20 ...........
F_ Washer 5/16 x 3/4 x 1/8 ...............
S Nut-Hex M8 x 1.25 ...................

Qty.
1
1
1
1
4
8
4

location and function
1. BELT TENSION HANDLE...
Turn handle counter
clockwise
to apply tension to bell turn handle
clockwise to release belt tension.
2. BELT TENSION LOCK HANDLES...
Tightening
handles locks motor bracket support and BELT
TENSION
HANDLE to maintain correct belt distance and tension.
3. HEAD LOCKS...
Lock the head to the column,
ALWAYS have them locked in place while operating the drill press,
4. SUPPORT LOCK...
Tightening locks table support to column. Always have it locked in place while
operating the Drill Press.
5. TABLE CRANK
. . . Turn clockwise to elevate
table. Support lock must be released before operating crank.
6. TABLE BEVEL LOCK...
Locks the table in any
position from 0'_-45 _
7. TABLE LOCK . . . Allows table
various positions and locked.

to be rotated

of controls

9. CHUCK...
accessory

Holds drill bit or other recommended
to perform desired operations.

10. BEVEL SCALE...
for bevel operations,
arm.
11. SPRING CAP...
spring tension

Shows degree table is tilted
Scale is mounted on side of
Provides

means to adjust quill

12. DEPTH SCALE...
Allows operator to adjust drill
press to drill to a desired depth.
13. DRILL "ON-OFF"
SWITCH . . . Turns drill press
on and off ....
also used to lock drill press in off
position.
14. LIGHT "ON-OFF"
and off.

SWITCH,..

Turns the light on

15. CHUCK KEY...
Used to tighten drill in the chuck
and also to loosen the chuck for drill removal.
16. DEPTH SCALE LOCK...
at selected
position.

Locks

the depth

scale

8. FEED HANDLE
. . . For moving the quill up or
down. One or two may be removed if necessary
whenever the workpiece is of such unusual shape
that it interferes with the handles.

¢t)
0

(.3
"_€:
o

0_-.
1-I J-

10
7

TABLE REMOVED
FOR CLARITY

assembly
WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL
ALL ASSEMBLY STEPS ARE COMPLETED.
FRAMING SQUARE MUST BE TRUE.
--

TOOLS

15/16" BOX END
MEDIUM
SCREWDRIVER

Check its accuracy as illustrated below.
DRAW LIGHT
STRAIGHT EDGE OF
LINE ON BOARD
BOARD 3/4" THICK--

NEEDED

.....
8-INCH

ASSEMBLY OF COLUMN
HARDWARE

, . .,+, ....

ADJUSTABLE
WRENCH

SHOULD BE NO GAP OR OVERLAP WHEN
SQUARE IS FLIPPED OVER IN DOTTED POSITION

AND TABLE

1. Position base on floor. Remove protective
and discard.

covering
COLUMN
SUPPORT

2, Remove protective sleeve from column tube and
discard. Place column assembly on base, and align
holes in column support with holes _n base.

10ram DIA, x 40mm
LONG BOLT

3. Locate (4) four lOmm Dia. x 40mm long bolts (see
illustration) in loose parts bag.

BASE

4. Install a bolt in each hole through column support
and base and tighten with adjustable wrench.

COLUMN

TABLE
SUPPORT

5. Locate table crank and support lock in loose parts
bag.
6+ Install support lock from left side into table support
and tighten by hand.
7+ Install table crank assembly
with an adjustable wrench,

and tighten

set screw

SL
LOCK
TABLE
SUPPORT

TABLE
CRANK

COLUMN
COLLAR

8. Position column collar over rack and tighten set
screw in collar, using 3ram HEX "L'" wrench.
supplied in loose parts bag. Collar should not be
angled on the column. Only tighten set screw
enough to keep collar in place: rack should still
slide freely in collar.

COLUMN

CAUTION: To avoid column or collar damage,
do not overtighten set screw.

INSTALLING

THE

SUPPORT
LOCK

TABLE

1. Loosen support lock and raise table support by
turning table crank clockwise until support is at a
working height level. Tighten support lock,

:RANK

TABLE
SUPPORT

RACK

.,,...._TABLE
SUPPORT

2. Remove protective covering from table and discard. Place table in table support and tighten table
lock (located under table) by hand.

TABLE
LOCK

iNSTALLING

THE

TABLE

HEAD

_CAUTION:
The head assembly
pounds.
Carefully
lift head.

weighs

about

1. Remove protective bag from head assembly
and
discard. Carefully lift head above column tube and
slide it onto column making sure head slides down
over column as far as possible. Align head with
table and base.
COLUMN

HEAD

HEAD
LOCK
SET
SCREWS

2. Using a 5mm HEX "L" wrench tighten the two
head lock set screws on the right side of the
head.

'_uc
C

MOUNTING

MOTOR

1. Locate four (4) 8mm Dia x 20mm long hex head
bolts, eight (8) flat washers, and four (4) hex nuts
among

FF"

MOTOR
BRACKET

loose parts.

2. head.Install
hex head

.f'_ S_
z j"
"_

MOTOR
BASE

_ _ _ y

bolts

through

motor

bracket

3. Place motor in position so motor base slots line up
with motor bracket slots. Install flat washers and
hex nuts as illustrated. (Do not tighten)
4. Motor shaft should be as close as possible
of round opening in belt guard.

HEX
NUT

_"
• -------------------_

to center

HEAD
BOLT
8mm

DIA.

x 20ram

LONG

BOLT

HEX

NUT

FLAT
WASHER

AT WASHER

iNSTALLiNG
1

MOTOR

Find the motor pulley

MOTOR
PULLEY

PULLEY
in loose

SET

parts bag.

SCREW

2. Slide pulley onto motor shaft. Line up the flat surface on the motor shaft with the set screw m pulley.
3. Make sure the pulley
guard.
4. Tighten
wrench.

the set screw

does
using

not rest on the lower
a 3ram

HEX

"L
FLAT
SURFACE

INSTALLING
WARNING:

AND TENSIONING

TO AVOID

INJURY

TAL STARTING ALWAYS
AND REMOVE
SWITCH
BELT ADJUSTMENTS.

STRAIGHT

BELT

DUE TO ACCIDEN-

EDGE

,,f_

TURN DRILL PRESS OFF
KEY BEFORE
MAKING

Tighten the motor mount nuts using an adjustable
wrench.
NOTE: To avoid rattles or other
must not touch lower belt guard.

noise,

motor

frame

_,
\
k

3. Release Belt Tension Lock handles located on
each side of Drill Press head by turning them
counterclockwise.

LOWER
BELT
GUARD

BELT
TENSION
LOCK
HANDLE

MOTOR
MOUNT
NUTS

MOTOR

BELT
TENSION
HANDLE

4. Loosen Belt Tension handle by turning clockwise.

5. Locate center pulley assembly in loose parts bag
and place in proper hole.

SPINDLE

6. Locate two (2) V-belts

PULLEY

in the loose parts bag.

7. Use speed chart inside belt guard to choose speed
for drilling operation. Install belts in correct position
for desired speed. The longer of the two belts is
always positioned between the spindle pulley and
idler pulley.
NOTE: Refer to chart inside
mended Drilling Speeds.

belt

guard

for RecomIDLER

8. Apply tension to belt by turning Belt Tension Handle
counter clockwise until belt deflects approximately
1/2 inch by thumb pressure at its center.
9. Tighten

Belt Tension

Lock Handles.

CAUTION:
Over tensioning belt may cause
start or damage bearings.
,0.

If belt slips while drilling,

readjust

motor not

belt tension.

BELT
TENSION
HANDLE

BELT GUARD

BELT GUARD KNq

5rnmDIA.x12mm LONG
SCREW
BELT GUARD KNOB

INSTALLING

PAN

HD.

BELT GUARD KNOB

1. To attach belt guard knob, locate knob and 5mm
Dia. x12mm long pan hd. screw in loose parts bag.
Install screw in hole located in guard and attach
knob turning until tight,
WARNING: TO AVOID POSSIBLE INJURY KEEP
GUARD IN PLACE AND IN PROPER WORKING
ORDER WHILE OPERATING.

PULLEY

BELT
TENSION
LOCK
HANDLE

MOTOR CONNECTIONS
WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL
ALL ASSEMBLY STEPS ARE COMPLETED.

BLACK WIRE TO
TERMINAL #1
COPPER POST

_,\V

_",_

I1 ""_t_--_3.

WHITE WIRE

power cord.
3. Reinsert GREEN SCREW in threaded hole that it
was removed from and tighten securely.
4. Insert terminal end of WHITE wire on spade _erminal (next to silver post) marked #4 on the motor.
Push terminal firmly until seated.

MOTOR

5. Insert terminal end of BLACK wire on spade terminal (next to copper post) marked # 1 on the motor.
Push terminal firmly until seated.

.ow°.

6. Close motor connector box being sure that power
cord is seated in strain relief groove and tighten
box cover screws.

.o.o.
oo.°w.,.;.
GREEN
(GROUND)

7. Do not plug in power cable.

INSTALLING

FEED HANDLES

HUB

1. Locate three (3) feed handles
amo'ng
leose
parts.
2. Screw the feed handles into the threaded holes
inthe hub and tighten.
FEED
HANDLE

INSTALLING

THE CHUCK

1. Ctean out the TAPERED HOLE in the chuck, Clean
the tapered surface on the arbor with a clean
cloth. Make sure there are no foreign particles sticking to the surfaces. The slightest piece of dirt on
any of these surfaces will prevent the chuck from
seating properly. This wilt cause the drill to
"wobble."

ARBOR

CLEAN THIS
SURFACE

JC:

_D
IC:

_J
C

SPINDLE

2. Slide the chuck up over the arbor as illustrated.

SUPPORT
LOC.K

4. Unlock support lock and raise table so its about
two (2) inches below tip of chuck.
5. Turn chuck sleeve clockwise
and open jaws in
chuck completely.
6. Turn feed handles counterclockwise
and force
chuck against table until chuck is secure.

CHUCK
SLEEVE

FEED
HANDLE

INSTALLING

LIGHT BULB

1. Install a light bulb (not larger than 60 watt) into the
socket inside the head,

ADJUSTING
TO HEAD

THE TABLE

SQUARE

NOTE: The combination square must be "true." See
"Unpacking and Checking Contents" section for
method.
1, Insert a precision ground steel rod approximately
3" long into chuck and tighten.
2. With table raised to working height and locked on
column, place combination square flat on table beside rod

TABLE

3. If an adjustment is necessary loosen the set screw
"
under be V e lock wth
3mm Hex L wrench, then
loosen the table bevel lock with a 1 5/16" wrench.
(These adjustments are located under the table).
4. Align the table square to the rod by rotating the
tal31euntil the square and rod are in line.
5. Retighten table bevel lock.
6. Retighten set screw.

TABLE
BEVEL
LOCK

SCREW

BEVEL SCALE

a quick method for beveling the table to approximate
angles. If precise accuracy is necessary, a square, or
other precision measuring tool should be used to position the table,

' L_._"_-_-'__
_,r_,,,,_
,_
"_-_. _

_=__

"_
I 11

3above),

b. Move table so desired angle on bevel scale is

straight across from zero line on table support.
C. Retighten table bevel lock and set screw.

POINTER

_ _

i
/

SCALE

_!_ _
IL_I \_..:._.
L,'] I
:_,'_
r_! |
_ (]_

1. TO use the bevel scale do the following:
a. Loosen set screw and table bevel lock (see step

TABLE

-_)

_'_

_1
I !
U
_
_

/ //

_*_--_J/

/
.,,,_,,_
_._
_'_._
-'__
t,_/"_._

.-'_J

getting to know your drill press
FEED SPRING
ADJUSTMENT

FEED
SPRING

17
SPRING
CAP

BELT

LIGHT "ON-OFF"
SWITCH

_L
O_

1
GUARD

DRILL "ON-OFF"
SWITCH

2
BELT TENSION
LOCK HANDLE

18
CHUCK
19
ARM

2
20
BEVEL
(UNDER

23
SUPPORT

LOCK

22
BEVEL SCALE

21
TABLE

LOCK

BELT
LOCK

TENSION
HANDLE

LOCK
3
BELT TENSION
HANDLE

TABLE)

16
DEPTH
SCALE
LOCK

4
HEAD LOCK

5
FEED HANDLE

15
DEPTH SCALE
INDICATOR

6
14
DEPTH SCALE
QUILL AND SPINDLE
INSIDE OF DRILL

COLUMN

ASSEMBLY
PRESS

COLLAR

7
TABLE SUPPORT
SPINDLE

B
TABLE CRANK

SPLINES
(GROOVES)
WEDGE KEY

13
TABLE
12
COLUMN

RACK
(TEETH)

11
COLUMN
SUPPC
24

CHUCK

_ ._..._

KEY

10
BASE

ARBOR

See inside of belt guard for specific placement of belts
on pulleys.

This Drill Press has 12 speeds as listed below:
250 RPM
990 RPM
340 RPM
1550 RPM
390 RPM
1620 RPM
510 RPM
1900 RPM
600 RPM
2620 RPM
650 RPM
3100 RPM

SPINDLE

SPEEDS

iN R,P.M.

250

340

390

510

600

65O

990

1550

1900

2620

3100

, r,

1620

1. BELT GUARD ASSEMBLY . .. Covers pulleys
and belt during operation of drill press.
2. BELT TENSION LOCK HANDLES...
Tightening
handles locks motor bracket support and BELT
TENSION HANDLE to maintain correct belt distance and tension.

14. DEPTH SCALE...
drilled.

Shows depth of hole being

15. DEPTH SCALE INDICATOR...
depth selected on depth scale.
16. DEPTH SCALE LOCK...
to selected depth.

3. BELT TENSION HANDLE... Turn handle counter
clockwise to apply tension to belt. turn handle
clockwise to release belt tension.

17. SPRING CAP ...
spnng tension.

Indicates drilling

Locks the depth scale

Provides means to adjust quill

18. CHUCK...
Holds drill bit or other recommended
accessory to perform desired operations.

4. HEAD LOCKS...
Lock the head to the column.
ALWAYS have them locked in place while operating the drill press,
5. FEED HANDLE . .. For moving the quill up or
down. One or two may be removed if necessary

19. ARM... Extends beyond table support for mounting and aligning the table.
20. TABLE BEVEL LOCK...
position from 00-45 °.

Locks the table in any

6. COLUMN COLLAR...
Holds the rack to the column. Rack remains movable in collar to permit
table support movements.
7. TABLE SUPPORT... Rides on column to support
arm and table.

21. TABLE LOCK,.. Table can be rotated in various
positions and locked,

8. TABLE CRANK . . . Turn clockwise to elevate
table, Support lockmust be released before operating crank.
9. RACK...
Combines with gear mechanism to provide easy elevation of table by hand operated table
crank,

23. SUPPORT LOCK...
Tightening locks table supportto column. Always have it locked in place while
operating the Drill Press.

22. BEVEL SCALE...
Shows degree table is tilted
for bevel operations. Scale is mounted on side of
arm,

24. CHUCK KEY .. , It is a self-ejecting chuck key
which will "pop" out of the chuck when you let go
of it. This action is designed to help prevent throwing of the chuck key from the chuck when power
is turned "ON", Do not use any other key as a
substitute, order a new one if damaged of lost.

10. BASE,.. Supports Drill Press. For additional stability, holes are provided in base to bolt Drill Press
to floor. (See "Additional Safety Instructionsfor Drill
Presses.")

25, BELTTENSION...
Referto section"Assembly-Installing and Tensioning Belt"

11. COLUMN SUPPORT... Supports column, guides
rack, and provides mounting holes for column to
base.

26. DRILLING SPEED... Can be changed by placing
the belt in any of the STEPS (grooves) in the pulleys. See Spindle Speed inside belt guard,

12. COLUMN...
Connects head, table, and base on
a one-piece tube for easy alignment and move-

To determine the approximate drilling speed, refer
to the table inside the belt guard.

support
workpiece.
18

27. DRILL "ON-OFF"
SWITCH . .. Has locking feature, THIS FEATURE
IS INTENDED
TO HELP
PREVENT
UNAUTHORIZED
AND
POSSIBLE
HAZARDOUS
USE
BY
CHILDREN
AND
OTHERS.
Insert KEY into switch,
NOTE:

Key is made

of yellow

plastic.

M,.

oO_

II
i

To turn drill ON.. ,
Insert finger under switch lever and pull.

To turn drill OFF...

.yd

Push lever in.

In an emergency;
... the drill bit BINDS...
STALLS
• . . STOPS . . . or tends to tear the workpiece loose
• • . you can QUICKLY turn the drill OFF by hitting the
switch with the palm of your hand.

To lock switch in OFF position..,
hold switch
one hand...
REMOVE key with other hand.

IN with

WARNING:
FOR YOUR OWN SAFETY,
ALWAYS
LOCK THE SWITCH "OFF" WHEN DRILL PRESS IS
NOT IN USE . .. REMOVE KEY AND KEEP IT IN A
SAFE PLACE . . . ALSO . . . IN THE EVENT OF A
POWER FAILURE (ALL OF YOUR LIGHTS GO OUT)
OR
BLOWN
FUSE
OR
TRIPPED
CIRCUIT
BREAKER,
TURN SWITCH OFF...
LOCK iT AND
REMOVE
THE KEY. THIS WILL PREVENT
THE
DRILL PRESS FROM STARTING
UP AGAIN WHEN
THE POWER COMES BACK ON.

piece.
2- Loosen the depth scale lock.
3. With the switch OFF, bring the drill down until the
TIP or lips of the drill are even with the Mark.

DEPTH
SCALE LOCK

4. Turn the depth scale counterclockwiseuntil it stops
moving.
5. Tighten the depth scale lock.
6. The drill willnow De stopped at this depth until the
depth scale is readjusted.

DEPTH
SCALE

MARK
\

ANOTHER

DEPTH

WAY -- DEPTH SCALE

SCALE

1. With the switch OFF, loosen the depth scalelock.
2. Turn the depth scale clockwise untilthe depth scale
indicator points to the desired drilling depth on the
depth scale.
3. Tighten the depth scale lock.

POINTER

4. The chuck or drill will now be stopped after traveling
downward the distance selected on the depth
scale.

LOCKING

CHUCK

DESIRED

DEPTH

1. With the switch off--loosen the depth scale lock.
2. Turn the feed handles until the chuck is at the
desired depth Hold feed handles at this position.

TIP TOUCHES
WORKPIECE

DEPTH SCALE
LOCK

3. Turn the depth scale clockwise until it stops.
4. Tighten the depth scale lock.
5. The chuck will now be he_d at this depth when the
feed handles are released.

SPINDLE KEY
HOLE

REMOVaNG CHUCK AND ARBOR

QUILL KEY
HOLE

ARBOR
SPINDLE

CHUCK
SLEEVE

1. With switch off -- adjust depth scale to hold drill
at a depth of (3) three inches. (See instructionsfor
"Locking chuck at desired depth").
2, Align key holes in spindle and quill by rotating the
chuck by hand. (See illustration)
3, Insert key wedge into key holes.
4, Tap key wedge lightly until the chuck and arbor
fall out of spindle,
NOTE: Place one hand below chuck to catch it when
it falls out.

WEDGE KEY

CHUCK
SLEEVE

BODY

=3c

RE'INSTALLING

THE

CHUCK

AND ARBOR

1. Clean the tapered surface on the arbor with a
clean cloth. Make sure there are no foreign
particles stickingto the surface. The slightest
piece of dirt on this surface will prevent the
arbor from seating properly. This will cause the
drill to "wobble."
SPINDLE

2. Slide arbor into spindle on drill press.
3. Push up on chuck/arbor
assembly
rotate them. You will feel rectangular
arbor slip into a notch in the spindle.

as you
end of

ARBOR

CHUCK
SLEEVE

WARNING: Make sure the rectangular end of the
arbor has slipped .into the notch in the spindle
before going on to Step 4. Failure to follow this
direction may allow the chuck to come loose
during operation, fly out, and hit the operator.

CHUCK
BODY

SUPPORT
LOCK
4. Unlock support lock and raise table so its about
two (2) inches below tip of chuck.
5. Turn chuck sleeve
chuck completely.
6. Turn feed handles
chuck against table

clockwise

and open

jaws

counterclockwise
and
until arbor is secure.

force

CHUCK
SLEEVE

FEED
HANDLE

CHI

basic drill press operation
Follow the following instructionsfor operating your drill
press to get the best results and to minimize the likelihood of personal injury.
WARNING: FOR YOUR OWN SAFETY, ALWAYS
OBSERVE THE SAFETY PRECAUTIONS HERE AND
ON PAGES 2, 3, AND 4.

Never do any work "FREEHAND"
(handholding workpiece rather than supporting
it
on the table), except when polishing.
-- Securely lock Head and Support to Column,
Table Arm to support, and Table to Table
Arm before operating drill press.
-- Never move the Head or Table while the
tool is running.
-- Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration.
-- If a workpiece overhangs the table such taht
it will fall or tip if not held, clamp it to the
table or provide auxiliary support.
Use fixtures
for unusual
operations
to
adequately
hold, guide and position workpiece.
- Use the SPINDLE SPEED recommended
for the specific operation and workpiece material-check
the panel inside of the guard
cover for drilling information;
for accessories, refer to the instructions
provided
with the accessories,
f. Never climb on the drill press Table, it could
break or pul! the entire drill press down on you.
g. Turn the motor Switch Off and put away the
Switch Key when leaving the drill press.
h. To avoid injury from thrown work or tool contact,
do NOT perform layout, assembly,
or setup
work on the table while the cutting tool is rotating.
2. Use only accessories
designed for this drill
press to avoid serious injury from thrown broken parts or work pieces.
a. Hotesaws must NEVER be operated on this drill
press at a speea greater than 400 RPM
b. Drum sanders must NEVER be operated
on
this drill press at a speed greater than 1800
RPM

1. Protection: Eyes, Hands, Face, Ears and Body
WARNING: TO AVOID BEING PULLED iNTO
THE SPINNING TOOL -1. Do
----2. Do

NOT wear:
gloves
necktie
loose clothing
jewelry
tie back long hair

If any part of your drill press is missing, malfunctioning,- has been damaged or broken..,
such
as the motor switch, or other operating control,
a safety device or the power cord . . . cease
operating immediately
until the particular
part
is properly repaired or replaced.

Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece should unexpectedly
shift or
your hand should slip.

To avoid injury from parts thrown by the spring,
follow instructions exactly as given and shown
in adjusting spring tension of quill.

To prevent the workpiece from being torn from
your hands, spinning of the tool, shattering the
tool or being thrown, always properly support
your work so it won't shift or bind on the tool:
-- Always position BACKUP MATERIAL (use
beneath the workpiece)
to contact the left
side of the column.
-- Whenever
possible,
position the WORKPIECE to contact the left side of the column-if
it is too short o.r the table is tilted.
clamp solidly to the table, use table slots or
clamping ledge around the outside edge of
the table.
--

c. Do not install or use any drill that exceeds 7" in
length or extends 6" below the chuck jaws. They
can suddenly bend outward or break.
d. Do not use wire wheels, router bits, shaper cutters, circle (fly) cutters or rotary planers on the
drill press.

When using a drill press VICE, always fasten
it to the table.

|NSTALLING

DRILLS

IN CHUCK

With the switch off and the key removed, insert drill
into chuck far enough to obtain maximum GRIPPING
of the CHUCK JAWS... the jaws are approx. 1" long.
When using a small drill do not insert it so far that the
jaws touch the flutes (spiral grooves) of the drill.
Make sure that the drill is CENTERED in the chuck
before tightening the chuck with the key.

KEY

JAWS

Tighten the drill sufficiently, so that it does not SLiP
while drilling.
Turn the chuck key clockwise
terclockwise to loosen.

to tighten--coun-

POSiTIONiNG

TABLE AND WORKPIECE

Lock the table to the column in a position so that the
tip of the drill is just a little above the top of the workpiece.
Always place a piece of BACK-UP MATERIAL (wood.
plywood..)
on the table underneath the workpiece.
This will prevent "splintering" or making a heavy burr
on the underside of the workpiece as the drill breaks
through. To keep the backup material from spinning
outof control, it must contact the left side of the column,
as illustrated.
WARNING: TO PREVENT THE WORKPIECE OR THE
BACKUP MATERIAL FROM BEING TORN FROM
YOUR HAND WHILE DRILLING, POSITION THEI_/I
AGAINST THE LEFT SIDE OF THE COLUMN. iF THE
WORKPICE OR THE BACKUP MATERIAL ARE NOT
LONG ENOUGH TO REACH THE COLUMN, CLAMP
THEM TO THE TABLE. FAILURE TO DO THiS
COULD RESULT iN PERSONAL INJURY.

WORKPIECE

MATERIAL

For small pieces that cannot be clamped to the table,
use a drill press vise (Optional accessory.)
WARNING: THE VISE MUST BE CLAMPED OR
BOLTED TO THE TABLE TO AVOID iNJURY FROM
SPINNING WORK AND ViSE OR TOOL BREAKAGE.

WORKPIECE
DRILL PRESS
VISE

BOLT OR CLAMP
VICE SECURELY

TiLTiNG

TABLE

To use the table in a bevel (tilted) position, loosen the
set screw under table bevel lock with Hex "L" wrench.
Loosen bevel lock with 15/t6" wrench.

BEVEL LOCK

Tilt table to desired angle by reading bevel scale. Retighten bevel lock and set screw.

BEVEL

SCALE

SET SCREW

WARNING:
TO AVOmD INJURY FROM SPINNING
WORK OR TOOL BREAKAGE,
ALWAYS
CLAMP
WORKPIECE
AND BACKUP MATERIAL SECURELY
TO TABLE
BEFORE
OPERATING
DRILL PRESS
WiTH THE TABLE TILTED.

Before turning the switch ON, bring the drill down to
the workpiece lining it up with the hole location.

FEEDBNG
Pull down on the feed handles
to allow the drill to cut.

To return table to original position: loosen set screw
and bevel lock, tilt table back to 0 ° on bevel scale, and
retighten set screw--then
tighten bevel lock.

effort

Feeding TOO SLOWLY might cause the drill to burn
• . . Feeding TOO RAPIDLY might stop the motor...
cause the belt or drill to SLIP...
tear the workpiece
LOOSE or BREAK the drill bit.

HOLE LOCATION
Make a DENT in the workpiece where you want the
hole.., using a CENTER PUNCH or a SHARP NAIL.

with only enough

When drilling metal, it may be necessary
the tip of the drill with motor oil to prevent
drill tip•

to lubricate
burning the

adjustments
NOTCH

WARNING: FOR YOUR OWN SAFETY TURN
SWITCH "OFF" AND REMOVE PLUG FROM POWER
SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. TO AVOID iNJURY FROM THROWN PARTS
DUE TO SPRING RELEASE, FOLLOW iNSTRUCTiONS CAREFULLY, AND WEAR EYE GOGGLES.

QUILL RETURN

BOSS

- SPRING CAP
JAM NUT
(OUTER)

NOTCH

SPRING

1. With the chuck at its highest possible position, turn
the depth scale clockwise until it stops and tighten
the depth scale lock. This will prevent the quill dropping while tensioning the spring•
2. Lower table for additional

STANDAR
NUT
(iNNER)

clearance.

8. Unlock depth scale lock and check
while turning feed handles.

3. Work from left side of Drill Press.
4. Place screwdriver in lower front notch of spring
cap, and hold it inplace while loosening and removing jam [outer] nut only.
5. With screwdriver remaining in notch, loosen large
standard [inner] nut (approximately 1/8") until notch
disengages from boss on head. DO NOT REMOVE
THIS NUT.
6. Carefully turn screwdriver counter clockwise and
engage next notch in boss. DO NOT REMOVE
SCREWDRIVER.
7. Tighten standard nut with wrench only enough to
engage boss. Do not overtighten as this will restrict
quill movement.

tensior_

9. If there is not enough tension on spring, repeat
steps 4-8 moving only ONE notch each time and
checking tension after EACH repetition.
10. Proper tension is achieved when quill returns gently
to full up position when released from 3/4" depth.
11. When there is enough tension after checking, replace jam nut and tighten to standard nut, BUT do
not overtighten against standard nut.
12. Check quill while feeding to have smooth and unrestricted movement. If movement is too tight,
loosen jam nut and SLIGHTLY loosen standard
nut until unrestricted. Retighten jam nut.
25

SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR DRILL PRESS.
Frequently blow out any dust that may accumulate inside the motor.
A coat of automobile-type
paste wax when applied
to the table and column will help to keep tlqe surfaces clean.
WARNING: TO AVOID SHOCK OR FIRE HAZARD,
IF THE POWER CORD IS WORN OR CUT, OR DAMAGED IN ANY WAY, HAVE IT REPLACED iMMEDIATELY.

lubrication
WHITE

All of the BALL BEARINGS are packed with grease
the factory. They requtre no further lubrication.

WIRE

at
WHITE

Periodically
lubricate the gear and rack. table elevation
mechanism, the SPLINES (grooves) in the spindle, and
the RACK (teeth of the quill). See "Getting to Know
Your Drill Press"

LIGHT

CONN

BLACK

JUMPER

BLACK

WIRING DIAGRAM

recommended accessories
WARNING: USE ONLY RECOMMENDED ACCESSORIES. FOLLOW iNSTRUCTIONS THAT ACCOMPANY ACCESSORIES. USE OF IMPROPER ACCESSORIES MAY CAUSE HAZARDS.

Drill Bits ........................
Hold-Down and Guide .................
Drill Press Vises ...................
Rotary Table .........................
Drill Press Mortising Kit ................
Hole Saw up to 2 1/2" dia. max .......
5 pc. Stop Collar Set ..................

See Catalog
9-2457
See Catalog
9-2495
9-29506
See Catalog
9-67063

Sanding Drums ................
9-2497 -- 9-2498
Buffing Wheels up to 4" dia. max .....
See Catalog
Polishing Wheel, 1 1/2" x 1". ............
9-64991
Power Tool Know-How Handbooks
Radial Saw .......................
9-2917
Table Saw ........................
9-2918

The recommended accessories listed here
are current and were available at the time
this manual was printed.

troubJe shooting
WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER
SOURCE OUTLET BEFORE TROUBLE SHOOTING.
® CONSULT

YOUR

LOCAL

TROUBLE

SEARS

SERVICE

PROBABLE

CENTER

IF FOR ANY REASON

MOTOR

WILL NOT RUN.

REMEDY

CAUSE

Noisy Operation

1. Incorrect belt tension.

1. Adjust tension, See section
"ASSEMBLY-TENSIONING
BELT."
2. Lubricate spindle, See "Lubrication"
section,
3. Check tightness of retaining nut on
pulley, and tighten if necessary.
4, Tighten setscrews in pulleys.

2. Dry Spindle.
3. Loose spindle pulley.
4. Loose motor pulley.
Drill Burns

1. Incorrect speed.

1. Change speed. See section "Getting
To Know Your Drill Press"...
DRILLING SPEED.
.
Retract drill frquently to clear chips.

2. Chips not coming out
of hole.
3. Dull Drill.

-3. Resharpen drill.
4. Feed fast enough..,
allow drill to cut.
5, Lubricate drill. See "Basic Drill Press
Operation" section.

4. Feeding too slow.
5. Not lubricated.

Drill toads off...
hole not round.

1. Hard grain in wood or
lengths of cutting
lips and/or angles
notequal.
2. Bent drill bit.

1, Resharpen

Wood splinters on
underside,

1. No "back-up material"
under workpiece.

1. Use "back-up material"... See Basic
Drill Press Operation" section.

Workpiece torn
loose from hand.

1. Not supported or
clamped properly.

1. Support workpiece or clamp it... See
"Basic Drill Press Operation" section.

Drill Binds in
workpiece.

1. Workpiece pinching drill
or excessive feed pressure.
2. Improper belt tension.

1, Support workpiece or clamp it... See
"Basic Drill Press Operation" section.
2. Adjust tension, .. See section
"ASSEMBLY-TENSIONING
BELT."

Excessive drill
runout or wobble.

1. Bent drill.
2. Worn spindle bearings.
3. Drill not properly
installed in chuck.
4. Chuck not properly installed.

1. Use a straight drill.
2. Replace bearings.
3. Install drill properly.,. See "Basic
Drill Press Operation" section.
4. Install chuck properly.., referto
"Unpacking and Assembly Instructions
•.. INSTALLING THE CHUCK."

Quill Returns
too slow or too
fast.

1, Spring hasimpropertension.

drill correctly.

Replace drill bit.

Adjust spring tension... See section.
"Adjustments--Quill Return Spring."

Always order by Part Number--Not

FIGURE

Key
No.
1
2
3
4
5
6
7
8

1 PARTS

Dart

",,.'"
,lu.u.
817325
817334
817544
STD315225
STD303240
817779-3
817543
817548

Key
No.

Description
Knob
Pivot-Idler
Pulley-Center
* Bearing-Ball 15mm
* Belt-"V" 3/8 x 24
Guard w/Labels
Pulley-Motor
Screw-Hex Soc. Set
M6x 1.0-8

* Standard Hardware Item -- May Be Purchased Locally,
28

by Key Number

LIST

Part
No.

817358-1

10
11
12
13
14
15
16
17

817534
816755-4
817537
817545
STD315245
817536
817327
817511-2

Description
Screw-Wash HD.
M6x1.0-16
insert-Pulley
Screw-PN HD. M5 x 0.8-12
Ring-Retaining
Pulley-Spindle
* Bearing-Ball 20mm
Spacer
Nut-Pulley
* Belt-"V" 3/8 x 26

repair parts
o_

\
Lf_

_N
N
€_

T "¸

,€_J

LU
o

G.
-J
-J

T--

o'J
T"

cD
€_

Zo_
W

¢/)T-

_z
G:.j
(.,)w
G:C3

0 o

/
\

o
€_

repair parts

r"
0

o
o
_J
o

o
Orn
OL

×o_
ooo
O9

I
E
o

€O9
-I=

repair parts
PARTS

LgST FOR CRAFTSMAN
15" DRfLL
MODEL NO. 113.213150

pF_ESS

I
2
3
4
5
6

817309
817310
817311
STD315235
817535
817532

3 PARTS

Hardware

Locknut M!7 x 1.0
Ring-Locking
Washer
* Bearing-Ball 17mm
Gasket-Quill
Tube-Quill

Item -- May Be Purchased

by Key Number
LIST

Key
No.

Description

7
8
9
10
11
i

* Standard

",J

FIGURE

PaN
No.

'4.

Always order by Part Number--Not

Key
No.

.F..I

Locally.

Part
No.
817326
817339
817340
817341
817531
,,

Description
Key-Drift
Key-Chuck
Chuck
Arbor
Spindle

PARTS LiST F O R CRAFTSMAN 15 " DRILL PRESS
MODEL NO. 113.213150

Always order by Part Number--Not

FIGURE
Key
No.

Part
No.

1
2

817478
817391-1

3
4

817776
817475

4 PARTS

by Key Number

LiST

Description

Key
No.

Collar-Rack
Screw-Hex Soc. Set
M6x1,0-10
Support-Table w/indicator
Tube-Column

10
11
12

817390-5
817288
817392

13
14
15
16
17
18 i

817290
817777-1
817575
817294
817350
817349

Part
No.

Description
Screw-Hex HD. M6x 1.0-12
Pin-Gear
Screw-Hex HD.
5/8-11 x 1-1/4
Clamp-Table
Arm-Table w/Scale
Table
Clamp-Column
Gear-Helical
Worm-Elevation

Notes:

SERVHCE

MODEL NO.
113.213150

Now that you have purchased
your 15-inch Drill Press, should
a need ever exist for repair parts or service, simply contact
any Sears Service Center and most Sears, Roebuck and Co.
store_ Be sure to provide all pertinent facts when you call
or visit.
The model
on a plate

number of your 15-inch Drill Press will be found
attached
to the rear of the head.

DRILL PRESS WITH
MAXIMUM
DEVELOPED
I HP MOTOR

HOW TO ORDER
REPAIR PARTS

WHEN ORDERING REPAIRPARTS,ALWAYS GIVE THE FOLLOWING
INFORMATION:
PARTNUMBER

PARTDESCRIPTION

MODEL NUMBER
113213150

NAME OF ITEM
MOTORIZED 15-INCH
FLOOR MODEL DRILLPRESS

All parts listed may be ordered from any Sears Service Center
and most Sears stores. If the parts you need are not stocked
locally, your order will be electronically
transmitted to a Sears
Repair Parts Distribution Center for handling.

Sold by SEARS, ROEBUCK AND CO., Chicago,
Part No. SP5187

Form

No. SP5187-4

IL 60684

U.S.A.
Printed

in Taiwan

2/92

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 36
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Fri May 22 04:19:08 2009
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 113213150 User Manual DRILL PRESS Manuals And Guides L0905102

CRAFTSMAN Drill Press Manual L0905102 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation