Craftsman 113244580 User Manual TWO WHEEL 9 BAND SAW Manuals And Guides L0910140

CRAFTSMAN Saw Band Manual L0910140 CRAFTSMAN Saw Band Owner's Manual, CRAFTSMAN Saw Band installation guides

User Manual: Craftsman 113244580 113244580 CRAFTSMAN TWO WHEEL 9 BAND SAW - Manuals and Guides View the owners manual for your CRAFTSMAN TWO WHEEL 9 BAND SAW #113244580. Home:Tool Parts:Craftsman Parts:Craftsman TWO WHEEL 9 BAND SAW Manual

Open the PDF directly: View PDF .
Page Count: 28

fSave This Manual

For Future Reference

S£ARS

owner's

manual

Model No.

113,244580

Two Wheel

9 Inch Band Saw

Serial

Number

Model and serial numbers

may be found at the rear of

the base.

You should record both

model and serial number in

a safe place for future use.

FOR YOUR

SAFETY

SE/ Uq S/CRAFTSMAN

TWO WHEEL

9 INCH BAND SAW

•assembly

•operating

•repair parts

READ ALL

INSTRUCTIONS

CAREFULLY

Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.

Part No. SP5872

Printed inTaiwan

FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW

If within one year from the date of purchase, this Craftsman Band Saw fails due to a defect in material

or workmanship, Sears will repair it, free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE

CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES,

This warranty applies only while this product is used in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

Sears, Roebuck and Co., D/817 WA Hoffman Estates, IL 60179

Safety Instructions For Band Saw

Safety Signal Words:

DANGER: means if the safety information is not followed

someone will be seriously injured or killed.

WARNING: means if the safety information is not followed

someone could be seriously injured or killed.

CAUTION: means if the safety information is not followed

someone may be injured.

Before Using The Saw:

IWARNING: to avoid mistakes that could cause seri- I

ous, permanent injury, do not plug the saw in until I

the following steps have been completed.

•Completely assemble and align saw (see "Assembly"

and "Alignment" section within).

•Learn the use and function of the ON-OFF switch,

table bevel and bevel lock knob, blade guides, backup

bearings and blade guard.

•Review and understand all safety instructions and

operating procedures inthis manual.

• Review the maintenance methods for this saw.

• Find and read all the warning labels found on the front

of the saw (shown below).

When Installing or Moving the Saw:

Avoid dangerous environment.

•Use the saw in a dry, indoor place protected from rain.

•Keep work area well lighted.

To avoid injury from unexpected saw movement.

• Put the saw on a firm level surface where there is

plenty of room to handle and properly support the

workpiece.

•Support the saw so the table is level and the saw does

not rock.

•Bolt the saw to the floor or work surface. Saw may slip,

walk or slide while cutting long or heavy boards.

•Turn saw off and unplug cord before moving the saw.

To avoid injury from electrical shock.

•Make sure your fingers do not touch the plug's metal

prongs when plugging in or unplugging the saw.

•Never stand on tool. Serious injury could occur if the

tool tips or you accidentally hit the cutting tool. Do not

store any items above or near the tool where anyone

might stand on the tool to reach them.

Before Each Use:

Inspect your saw.

•To avoid injury from accidental starting, turn the switch

off, unplug the saw, and remove the switch key before

changing the setup, removing covers, guards or blade.

• Check for alignment of moving parts, binding of moving

parts, breakage of parts, saw stability, and any other

conditions that may affect the way the saw works.

•If any part is missing, bent or broken in any way, or any

electrical part does not work properly, turn the saw off

and unplug the saw.

•Replace damaged or missing parts before using the

saw again.

•Maintain tools with care, Keep the saw clean for best

and safest performance. Follow instructions for lubri-

cating.

•Remove adjusting keys and wrenches. Form a habit of

checking for and removing keys and adjusting

wrenches from table top before turning it on.

ADVSmlENClA

ALLOW

TOO L TO

sTOp

BEFORE

ADJUSTING

_EQUE LA

HERRAf£Ek'TASE

DETENGAANTES

DEI_.ALIZ_

_JSl"ES

To avoid injury from jams, slips, thrown pieces or

broken blades.

Inspect your blade.

• Choose the right blade size, style and cutting speed for

the material and the type of cutting you plan to do,

• Use only recommended accessories. Consult this

owners manual for recommended accessories. Follow

the instructions that come with the accessories. The

use of improper accessories may cause risk of injury to

persons.

•Make sure the bladeteeth point downward, toward the table.

•Make sure the blade guides and thrust bearings are

properly adjusted.

• Make sure the blade tension is properly adjusted.

• Make sure the bevel clamp is tight and no parts have

excessive play.

• To avoid accidental blade contact, minimize blade

breakage and provide maximum blade support, always

adjust the upper blade guide and blade guard to just

clear the workpiece.

Inspect your work area.

•Keep work area clean.

•Cluttered areas and benches invite accidents. Floor

must not be slippery from wax or sawdust.

• To avoid burns or other fire damage, never use the saw

near flammable liquids, vapors or gases.

Plan Your Work.

• Use the right tool. Don't force tool or attachment to do

a job it was not designed to do.

•Use this band saw to cut only wood, wood like prod-

ucts and plastics.

CAUTION: To avoid blade breakage, fire or other

damage to the saw, never use this band saw to cut

metals,

• To avoid injury from accidental contact with moving

parts, don't do layout, assembly, or set up work on the

saw while any parts are moving.

• Avoid accidental starting. Make sure switch is "OFF"

before plugging saw into apower outlet.

• Plan ahead to protect your eyes, hands, face and ears.

Dress for safety

• Any power saw can throw foreign objects into the eyes.

This can cause permanent eye damage. Wear safety

goggles (not glasses) that comply with ANSI Z87.1

(shown on package). Everyday eyeglasses have only

impact resistance lenses. They are not safety glasses.

Safety goggles are available at Sears retail stores.

Glasses or goggles not in compliance with ANSI Z87.1

could seriously hurt you when they break.

WEAR YOUR

;Do not wear loose clothing, gloves, neckties or jewelry

(rings, wrist watches). They can get caught and draw

you into moving parts.

• Wear nonslip footwear.

• Tie back long hair.

• Roll long sleeves above the elbow.

•Noise levels vary widely. To avoid possible hearing

damage, wear ear plugs or muffs when using saw for

hours at a time.

•For dusty operations, wear a dust mask along with the

safety goggles.

Inspect your workpiece.

Make sure there are no nails or foreign objects in the

part of the workpiece to be cut.

Use extra caution with large, very small or awkward

workpieces:

•Use extra supports (tables, saw horses, blocks, etc.)

for any workpieces large enough to tip when not held

down to the table top.

• Never use another person as a substitute for a table

extension, or as additional support for a workpiece that

is longer or wider than the basic saw table, or to help

feed, support or pull the workpiece.

• When cutting irregularly shaped workpieces, plan your

work so it will not slip and pinch the blade. A piece of

molding for example, must lie flat or be held by a fixture

or jig that will not let it twist, rock or slip while being cut.

•Properly support round material such as dowel rods, or

tubing. They tend to roll during a cut, causing the blade

to "bite". To avoid this, always use a "V" block or clamp

the work to the miter gage.

• Cut only one workpiece at a time.

• Clear everything except the workpiece and related

support devices off the table before turning the saw on.

Plan the Way You Will Hold the Workpiece

From Start To Finish.

•Do not hand hold pieces so small that your fingers will

go under the blade guard. Use jigs or fixtures to hold

the work and keep your hands away from the blade.

• Secure work. Use clamps to hold work when practical.

It's often safer than using your hand, and frees both

hands to operate the tool.

• Don't overreach. Keep good footing and balance.

Safety Instructions for Band Saws (continued)

Whenever Sawblade Is Moving:

WARNING: Don't let familiarity (gained from fre-

quent use of your band saw) cause a careless mis-

take. Always remember that a careless fraction of a

second is enough to cause a severe injury.

•Before starting your cut, watch the saw while it runs. If

it makes an unfamiliar noise or vibrates a lot, stop

immediately. Turn the saw off. Unplug the saw. Do not

restart until finding and correcting the problem.

•Before removing loose pieces from the table, turn saw

off and wait for all moving parts to stop.

Keep Children Away.

•Keep all visitors a safe distance from the band saw.

• Make sure bystanders are clear of the band saw and

workpiece.

Don't Force Tool.

• Let the blade reach full speed before cutting.

• It will do the job better and safer at its designed rate.

• Feed the workpiece into the saw only fast enough to let

the blade cut without bogging down or binding.

Before freeing jammed material.

• Turn switch "OFF".

•Unplug the saw.

• Wait for all moving parts to stop.

• Remove switch key.

When backing up the workpiece, the blade may bind

in the kerr (cut). This is usually caused by sawdust

clogging up the kerf or because the blade comes out

of the guides. If this happens:

•Turn saw "OFF"

• Wait for all moving parts to stop.

• Remove switch key.

• Unplug the saw.

• Remove band saw cover.

• Stick flat blade screwdriver or wedge into the kerf.

• Turn the upper wheel by hand while backing up the

workpiece.

Before Leaving the Saw.

• Turn the saw off.

• Wait for all moving parts to stop.

• Unplug the saw.

° Make workshop child-proof.

- Lock the shop.

- Disconnect master switches.

- Remove the yellow switch key. Store it away from

children and others not qualified to use the tool.

Glossary Of Terms For Woodworking

Beveling

An angle cutting operation made through the face of the

workpiece.

Compound Cutting

Asimultaneous bevel and miter crosscutting operation

Crosscut

A cutting operation made across the width of the work-

piece.

FPM

Feet per minute. Used in reference to surface speed of

blade.

Freehand (as used for band saw)

Performing a cut without the workpiece properly sup-

ported on the work table.

Gum

A sticky, sap based residue from wood products.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a nonthrough or partial cut.

Leading End

The end of the workpiece which, is pushed into the cut-

ting tool first.

Mitering

An angle cutting operation made across the width of the

workpiece.

Push Stick

A device used to feed the workpiece through the saw dur-

ing narrow ripping type operations and helps keep the

operator's hands well away from the blade.

Resaw

Acutting operation to reduce the thickness of the work-

piece to make thinner pieces.

Resin

Asticky, sap based substance that has dried.

Ripping

Acutting operation along the length of the workpiece.

Sawblade Path

The area of the worktable or workpiece directly in line

with the saw blade.

Set

The distance the tip of the sawblade tooth is bent out-

ward from the face of the blade.

Trailing End

The workpiece end last cut by the blade.

Workpiece

The item on which the cutting operation is being per-

formed. The surfaces of a workpiece are commonly

referred to as faces, ends, and edges.

Worktable

The surface on which the workpiece rests while perform-

ing a cutting or sanding operation.

Motor Specifications and Electrical Requirements

Power Supply and Motor Specifications

The A-C motor used in this saw is non-reversibletype, hav-

ing the followingspecifications:

Maximum Developed H.P. ........................................ 113

Voltage .................................................................... 120

Amperes ................................................................... 2.5

Hertz (Cycles) ........................................................... 60

Phase .................................................................. Single

RPM ...................................................................... 1750

Rotation of Shaft ............................... Counterclockwise

WARNING: To avoid electrocution: Do not let fin-

gers touch the terminals of plugs when installing

or removing the plug to or from the outlet.

WARNING: If not properly grounded, this power

tool can cause an electrical shock, particularly

when used in damp locations close to plumbing. If

an electrical shock occurs there is the potential of

a secondary hazard, such as your hands contact-

ing the sawblade.

WARNING: To avoid electrocution or fire, if power

cord is torn or cut, or damaged in any way, have it

replaced immediately.

Your unit is for use on 120 volts, and has a plug that looks

like the one below.

Properly

Grounded

Outlet

9-Prong

Plug

Gr;rUnnd_ng

This power tool is equipped with a3-conductor cord and

grounding type plug listed by Underwriters' Laboratories.

The ground conductor has a green jacket and is attached

to the motor at one end and to the ground prong in the

attachment plug at the other end. If repair or replacement

of the electric cord or plug is necessary, do not connect

the equipment grounding conductor to a live terminal.

This plug requires a mating 3-conductor grounding type

outlet as shown. This outlet must be installed and

grounded in accordance with all local codes and ordi-

nances.

WARNING: To avoid electrocution, if the outlet you

are planning to use for this power tool is of the two

prong type, Do Not Remove Or Alter The Ground-

ing Prong In Any Manner. Use an adapter as shown

below and always connect the grounding lug to a

known ground.

It is recommended that you have a qualified electrician

replace the Two prong outlet with a properly grounded

Three prong outlet.

Grounding Lug

Make Sure This Is

3-Prong Connected to a

Plug Known Ground

Receptacle

Adapter

An adapter, as illustrated, is available for connecting

plugs to 2-prong receptacles.

WARNING: The green grounding lug extending

from the adapter must be connected to a perma-

nent ground such as to a properly grounded outlet

box. Not all outlet boxes are properly grounded.

If the grounding instructions are not completely under-

stood or if you are not sure that your tool or outlet box is

properly grounded, check with a qualified electrician.

NOTE: The adapter illustrated is for use only if you

already have a properly grounded 2-prong receptacle.

Motor Safety Protection

NOTE: To avoid motor damage this motor should be

blown out or vacuumed frequently to keep sawdust from

interfering with normal motor ventilation.

1. This tool should be connected to a120v, 15 amp

branch circuit with a15 amp fuse or circuit breaker.

Failure to use the proper size fuse can result in dam-

age to the motor.

2. If the motor fails to start, turn the power switch to the

"OFF" position immediately. Unplug the tool. Check the

sawblade to make sure it turns freely. If the blade is

free, try to start the motor again. If the motor still does

not start, refer to the "Motor Troubleshooting Chart".

3. If the motor suddenly stalls while cutting wood, turn the

power switch off, unplug the tool and free the blade

from the wood. The motor may now be restarted and

the cut finished.

4. Frequent "blowing" of fuses or tripping of circuit break-

ers may result if:

a. Motor is overloaded - Overloading can occur if you

feed too rapidly.

b. Low Voltage - Although the motor is designed for

operation on the voltage and frequency specified on

the motor nameplate, normal loads will be handled

safely on voltages not more than 10% above or

below the nameplate voltage. Heavy loads, however,

require voltage at motor terminals equals the volt-

age specified on nameplate.

c. Improper or dull blades are used.

Motor Specifications and Electrical Requirements (continued)

5. Motor troubles may be traced to loose or incorrect con-

nections, overload, reduced input voltage (such as

small size wire in the supply circuit) or to overly long

supply circuit wire. Always check the connections, the

load and the supply circuit whenever motor fails to per-

form satisfactorily. Check wire size and length with the

Wire Size Chart as follows.

Wire Sizes

NOTE; Make sure the proper extension cord is used and

is in good condition.

The use of any extension cord will cause some loss of

power. To keep this to a minimum and to prevent over-

heating and motor burn-out, use the table below to deter-

mine the minimum wire size (A.WG.) extension cord.

Use only 3-wire extension cords that have 3-prong

grounding type plugs and 3-pole receptacles which

accepts the tools plug.

Extension A.W.G.

Cord Length

110-120V

0-25 Ft. 18

26 - 50 Ft. 16

Table of Contents

Safety Instructions For Band Saw ................................. 2

Safety Signal Words: ................................................. 2

Before Using The Saw: .............................................. 2

When Installing or Moving the Saw: .......................... 2

Before Each Use: ....................................................... 2

Plan Your Work .......................................................... 3

Dress for safety.......................................................... 3

Plan the Way You Will Hold the Workpiece From

Start To Finish ......................................................... 3

Whenever Sawblade is Moving .................................. 4

Before Leaving the Saw ............................................. 4

Glossary Of Terms For Woodworking ............................ 4

Motor Specifications and Electrical Requirements ........ 5

Power Supply and Motor Specifications .................... 5

Motor Safety Protection ............................................. 5

Wire Sizes .................................................................. 6

Table of Contents ........................................................... 6

Unpacking and Checking Contents ............................... 7

Tools Needed ............................................................. 7

Unpacking .................................................................. 7

List of Loose Parts ..................................................... 8

Assembly ....................................................................... 9

Installing the Table ..................................................... 9

Installing the Blade .................................................. 10

Alignment (Adjustments) ............................................. 11

Tensioning the Blade ............................................... 11

Tracking the Blade ................................................... 11

Adjusting Upper Blade Guard Assembly ................. 12

Aligning the Table Square to the Blade .................... 12

Adjusting the Blade Guides and Back-Up Bearing .. 13

Adjusting Motor Belt Tension ................................... 14

Mounting the Band Saw .............................................. 14

Mounting Band Saw to Workbench ......................... 14

Clamping Band Saw to Workbench ......................... 15

Mounting Band Saw to Accessory Legset

Cat. No. 9-22244 ................................................... 15

Legset Mounting Holes for Band Saw ..................... 15

Getting to Know Your Band Saw ............................ 16-17

Safety Instructions for Basic Band Saw Operation ...... 18

Before Using the Saw: ............................................. 18

When Installing or Moving the Saw: ........................ 18

Before Each Use: .................................................... 18

Plan Your Work ........................................................ 18

Dress For Safety ...................................................... 19

Plan the Way You Will Hold the Workpiece From

Start To Finish; ...................................................... 19

Whenever Sawblade is Moving ............................... 19

Before Leaving the Saw........................................... 19

Basic Band Saw Operations ........................................ 20

General Cutting ....................................................... 20

Circle Cutting ........................................................... 20

Relief Cuts ............................................................... 20

Maintenance ................................................................ 21

Tires ....................................................................... 21

General Maintenance .............................................. 21

Motor ...,................................................................... 21

Lubrication ............................................................... 21

Sears Recommends the Following Accessories ......... 21

Troubleshooting........................................................... 22

General .................................................................... 22

Motor ....................................................................... 23

Repair Parts ................................................................ 24

Unpacking and Checking Contents

Tools Needed

Tools required for assembly and alignment:

•#2 Phillips screwdriver

•Adjustable wrench.

• Combination Square

#2 Phillips Screwdriver

6" Adjustable Wrench Combination Square

Combination Square Must be True

Straight Edge of

Draw Light Board 3/4" Thick

Line on Board This Edge Must be

A I°iill il i_ieiieltlw i ii rl iiilr e

is Flipped Over in Dotted Position

Unpacking

WARNING: To avoid injury from unexpected start-

ing or electrical shock, do not plug the saw in until

all assembly and alignment steps are complete.

The power cord must remain unplugged whenever

you are working on the saw.

Unpacking and Checking Contents

1. Separate all "loose parts" from packaging materials

and check each item with "Table of Loose Parts" to

make sure all items are accounted for, before discard-

ing any packing material.

WARNING: If any parts are missing, do not attempt

to assemble the band saw, plug in the power cord,

or turn the switch on until the missing parts are

obtained and are installed correctly.

2. Sometimes small parts get lost in packaging materials.

Do not throw away any packaging untilyour saw is put

together. If you are missing a part, check packaging

before contacting Sears.

Unpacking and Checking Contents (continued)

List of Loose Parts

NOTE: Before beginning assembly, check that all parts

are included. If you are missing any part, do not assem-

ble the saw. Contact your Sears Service Center to get the

missing part. Sometimes small parts can get lost in pack-

aging material. Do not throw away any packaging until

saw is put together. Check packaging for missing parts

before contacting Sears. A complete parts list "Repair

Parts" is at the end of the manual. Use the list to identify

the number of the missing part.

The following parts are included:

Item

Description Qty.

Basic Saw Assembly........................................... 1

Owners Manual................................................... 1

Saw Table Assembly ........................................... 1

Blade................................................................... 1

Loose Parts Bag ................................................. 1

Containing the following parts:

F Wing Nut 1/4-20 .................................................. 1

G Screw, Truss Hd. 1/4-20 x 3/4 ............................. 1

H Washer 1/4 ......................................................... 1

J Wrench, 1/8" Hex"L" ......................................... 1

K Screw, Flat head 1/4-20 x 7/8 ............................. 3

L Nut hex 1/4-20 .................................................... 3

M Lockwasher 1/4 ................................................... 3

N Key Switch .......................................................... 1

P Screw 3/16-24 x 3/8 ......................................... ,..1

R Indicator .............................................................. 1

KL@NP

Assembly

WARNING: For your own safety, never connect

plug to power source outlet until all assembly

steps are complete, and you have read and under-

stood the safety and operational instructions.

From the

Item No.

loose parts find the following items:

Description Qty

1/4-20 x 7/8" Flat head screws ...................... 3

1/4-20 Hex nuts ............................................. 3

1/4 Lockwasher ............................................. 3

1/4-20 x 3/4 Truss head screw ....................... 1

1/4-20 Wing nut ............................................. 1

1/4 Washer .................................................... 1

Switch Key ..................................................... 1

1/8" He× "L" Wrench ...................................... 1

3/16-24 x 3/8 Screw ....................................... 1

Indicator ......................................................... 1

Table w/Insert (not pictured) .......................... 1

Sawblade (not pictured) ................................. 1

Installing the Table

Get table from among loose parts.

1. Place table with insert onto trunnion and align holes in

the table to those in the trunnion. Use the three 1/4-20

fiat head screws, three 1/4 Iockwashers and the three

1/4-20 he× nuts to secure table. Tighten nuts with an

open end or an adjustable wrench.

2. Loosen the table lock knob and turn the table tilt knob

to change the angle of the table. If the table is loose or

too tight, adjust the hex head bolt with an open end or

an adjustable wrench until firm, smooth table tiltopera-

tion is achieved. "Hex Head

Bolt

Table

Knob

3. Assemble the bevel indicator to the saw frame using

the 3/16-24 x 3/8 screw.

Bevel

Indicator

Assembly (continued)

Installing the Blade

I WARNING: Turn off saw, remove switch key andlunplug saw before removing or installing blade. I

1. Open front cover by pushing in upper and lower

latches.

2. Loosen the upper slide lock knob and position the

blade guard/guide assembly about half way between

the table and the frame. Tighten the lock knob:

Slide

Lock

Knob

CAUTION: To avoid serious eye injury or scrapes, if

the blade should suddenly uncoil, wear safety gog-

gles. Carefully uncoil the blade holding it at arms

length.

3. Uncoil the blade.

4. Slide the blade into the slot of the table with the teeth

facing toward front of saw and down toward the table.

5. RaGe the blade on both wheels. Center the blade on

the rubber tires.

NOTE: If the blade will not reach around both wheels,

lower the upper wheel by turning the tension adjustment

knob counterclockwise.

NOTE; Close the band saw cover after blade is properly

installed.

6. Assemble the truss head screw, washer and wing nut

to the table. The washer and wing nut are positioned

below the table.

Tension Adjusting

Knob

Head

Screw

fWasher

Alignment (Adjustments)

Tensioning the Blade

IWARNING: Cut material can be thrown. Eyes can

be permanently damaged. Wear your safety gog-

gles.

IWARNING: Turn off saw, remove switch key and

unplug before adjusting.

1. Turn blade tension adjusting knob clockwise until the

proper section of knob stern is aligned with top of band

saw frame. See illustration for blade size and "Align-

ment" section.

NOTE; Be careful not to overtension the blade, Too much

tension may tend to cause blade breakage. Too littleten-

sion may cause the blade to slip on the wheels. The ten-

sion adjusting knob has a knurled section on it. These

adjustment areas are approximate and may change

slightly depending on actual blade length.

Tension Adjusting Knob

Topj_ 3/8" Blade

1/4" Blade

Knurled j[' I ''_'--- 1/8'' Blade

Section I____]

Tracking the Blade

I WARNING: Turn off saw, remove switch key and I

unplug before adjusting. I

NOTE: Blade tension must be properly adjusted before

tracking the blade.

1. Open the cover and slowly turn the upper wheel clock-

wise by hand and watch the blade on the upper tire. If

the blade moves away from the center of the tire the

tracking must be adjusted.

2. Insert the 1/8" hex wrench into the tracking adjustment

screw located on the back of the saw behind the upper

wheel.

a. If the blade moved toward the front of the saw turn

the adjustment screw in (clockwise) while turning

the wheel by hand, untilthe blade rides in the center

of the tire.

b. If the blade moved away from the front of the saw,

turn the adjustment screw out (counterclockwise)

while turning the wheel by hand, untilthe blade rides

in the center of the tire.

3. Check the position of the blade on the lower tire. The

blade should be completely on the tire. If not, adjust

the tracking untilthe blade is on both tires.

4. Rotate the upper wheel by hand in a clockwise direc-

tion for afew more turns. Make sure the blade stays in

the same location on the tires. Readjust if necessary,

untilblade is tracking properly.

NOTE: The 1/8" blade may not track properly in the cen-

ter of the wheel. It may be better to track this blade on the

back half of the upper wheel. (See Illustration)

5. Replace hex wrench in holder located on the inside of

the front cover. Close cover making sure the upper and

lower latches catch.

Tracking Adjustment 7

Set Scre__ F

Blade

3ack of

Wheel

1/8" Blade on Back Half

Of Upper Wheel

Alignment (Adjustments) (continued)

Adjusting Upper Blade Guard Assembly

The upper blade guard assembly should always be set

about 1/8" above or as close as possible to the top sur-

face of the workpiece being cut.

Upper Slide

Lock Knob

1. Loosen the upper slide lock knob. Upper Guard Assembly

2. Rotate the upper slide adjusting knob to position the

guard assembly to the desired position.

3. Tighten the upper slide lock knob.

Upper Slide

Adjusting Knob

Aligning the Table Square to the Blade

IWARNING: Turn off saw, remove switch key and

unplug before adjusting.

1. Loosen the upper slide lock knob and position the

guide assembly all the way up. Tighten the lock knob.

2. Loosen table lock knob.

3. Place a small square on the table beside the blade as

illustrated.

4. Holding the left edge of the table (near the zero stop

set screw), tilt the table up or down to align table 90 ° to

blade (0° position). Tighten lock knob,

5. Adjust the zero stop set screw using the 1/8" hex

wrench until the set screw just touches the frame.

6. Check squareness of blade to table. Make readjust-

ments if necessary.

7. Check table bevel indicatorfor accuracy, Loosen screw

and adjust if necessary. Retighten screw.

Zero Stop

Set Screw

Adjusting the Blade Guides and Back-Up

Bearing

I WARNING: Turn off saw, remove switch key and I

unplug before making any adjustments. I

NOTE: The upper and lower blade guides and back-up

bearings support the band saw blade during cutting oper-

ations. The adjustment of the guides and bearings should

be checked whenever a different blade is installed.

1. Adjust the position of the blade guide support hous-

ings. Loosen the upper blade guide support housing

cap screw using a1/8 Hex "L" wrench.

2. Slide the upper blade guide support housing on the

shaft until the front edge of the blade guides are about

1/32" behind the gullet of the blade. Tighten the cap

screw.

3. Repeat for the lower blade guide support housing. (You

may need to adjust the blade tracking before making

this adjustment.)

NOTE; If the front face of the blade guides are not 1/32"

behind the gullet of the blade the blade teeth will hit the

blade guides and this will ruin the blade. Proper adjust-

ment of the upper and lower blade guide support hous-

ings will prevent this from happening.

3. Adjust the blade guides. Loosen the two cap screws

that lock the upper blade guides into the housing and

press the two guides evenly against the sides of the

blade but do not pinch the blade. Release the guides

and rotate the upper wheel slightly clockwise moving

the blade downward. Make sure one guide is not fur-

ther away from the blade than the other. Tighten both

cap screws.

4. Repeat on the lower blade guides.

NOTE; Ideally, the space between the blade and the

guides should be approximately the thickness of adollar

bill. This will provide maximum blade support and control

during cutting operations

5. Adjust the upper and lower back-up bearings. Loosen

the back up bearing cap screw using a 1/8" Hex "L"

wrench.

6. Move the back-up bearings to within 1/32" or less of

the back edge of the blade.

NOTE: The back-up bearing is used to support the back

edge of the blade while cutting. The blade should just

barely contact the bearings when you stop cutting.

Upper

Back-u

Bearing

Upper Blade

Guide

Housing

BI;

Lowe

Guide

Support Housin

Lower Back-u

Bearing

Upper

Bearing

Cap Screw

Guide

Support Housing

Cap Screw

Upper

Bearing

Cap Screw

Blade

Guide Support

Housing

Cap Screw

Lower Blade Guide

Support Housing

CaD Screw

///./,@v/_ U

:r Back-Up

Bearing Cap Screw

Alignment (Adjustments) (continued)

Adjusting Motor Belt Tension

WARNING: Turn off saw, remove switch key and I

unplug before making any adjustments. I

1. Test for proper belt tension. Open front cover. Rotate

lower wheel so you can access both sides of the motor

pulley. Place your thumb and index finger over the out-

side of the belt. Squeeze the two sides of the belt

together. There should be about 1/4" of give to the belt.

NOTE: Excessive tightness of belt may cause increased

noise and overload motor. Excessive looseness of belt

may cause belt to fail prematurely.

2. If adjustment is necessary, loosen the upper motor

bolt and lower motor pivot bolt. Move the motor to cor-

rect the belt tension. Retighten both motor bolts.

3. Recheck belt tension and readjust as necessary. Close

the front cover of saw when procedure is completed.

Upper Motor Bolt

Mounting the Band Saw

Mounting Band Saw to Workbench

If band saw is to be used in a permanent location, it

should be fastened securely to a film supporting surface

such as a workbench.

If mounting to a workbench, holes should be drilled

through supporting surface of the workbench using

dimensions illustrated.

1. Each leg should be bolted securely using 5/16" diame-

ter machine screws, Iockwashers, and 5/16" hex nuts

(not included). Screw length should be 1-3/4" plus the

thickness of the bench top.

2. Locate and mark the holes where band saw is to be

mounted.

3. Drill (4) 3/8" diameter holes through workbench.

4. Place band saw on workbench aligning holes in feet

with holes drilled in workbench.

5. Install all four 5/16" screws, Iockwashers and nuts and

tighten.

NOTE: All bolts should be inserted from the top. Install

the washers and nuts from the underside of the bench.

Lower Motor Pivot Bolt

3/8" DIAMETER I

6" I (4) HOLES

1' '

-_- tt" --_-_

An alternate method of mounting is to fasten band saw to

amounting board. The board should be of sufficient size

to avoid tipping of saw while in use. Any good grade of

plywood or chipboard with a 3/4" minimum thickness is

recommended. Thinner chipboard can break.) Once the

saw is mounted, securely clamp the board to the work-

bench using "C" clamps.

WARNING: Supporting surface where band saw is

mounted should be examined carefully after

mounting to insure that no movement during use

can result, If any tipping or walking is noted, secure

workbench or supporting surface before operating

band saw.

18" MIN,

24" MIN.

11"

Clamping Band Saw to Workbench

The band saw can be clamped directly to a workbench

using two (2) or more "C" clamps on base of unit.

Mounting Band Saw to Accessory Legset Cat. No. 9-22244

o Oaoa ,,,d

O O O

Attach to holes indicated by "m"

Legset Mounting Holes for Band Saw

Recommended mounting hardware (not included)

Description Qty

,5/16-18 x 1-1/2 he× hd, bolts ........................................ ,4

5/16 fiat washers .......................................................... 4

5/16 Iockwashers ......................................................... 4

5/16-18 hex nuts .......................................................... 4

Getting to Know Your Band Saw

1. Blade Guides - Supports the blade and keeps it from

twisting during operation. An adjustment is necessary

when blades are changed or replaced.

2. Back up bearings support the back of blade

3. Upper Slide Lock and Adjustment Knobs - Loosen

outer knob to unlock. Turn inner knob to adjust.

Retighten outer knob to lock upper blade guard/slide

in place.The upper blade guide assembly should just

clear the workpiece while cutting. Always adjust the

upper guide assembly and lock by tightening the

upper slide lock knob before turning on the band saw.

4. Table Lock and Adjustment Knobs -Loosen outer

knob to unlock. Turn inner knob to adjust. Retighten

outer knob to lock table in place.

5, Tilt (Bevel) Scale - Shows degree table is tilted for

bevel cutting.

6. Tension Adjustment Knob - Controls the amount of

blade tension when changing blades.

7. Tracking Adjustment Set Screw -Adjust to Keep

blade running in center of wheels.

8. Sawdust Ejection Port -Sawdust is eliminated from

inside machine. Also, makes an excellent hook-up for

a Wet/Dry vac.

9. Front cover may be opened for making adjustments

to machine.

10. Wrench Holder - Keeps 1/8" hex "L" wrench conve-

niently stored for blade guide and tracking adjust-

ments.

11. Wheel Brushes - Cleans dust from wheels during

operation.

12. Blade Guard -The blade guard protects the operator

from contacting the blade. The blade guard should be

adjusted as close as possible to the top of the work-

piece.

10 Wrench Holder

9 Front Cover

Ejection

Port

6Tension Adjustment Knob

12 Blade Guard

Back Up

Bearings

(Above and

Below Table)

Upper Slide Tracking

Lock and 7Adjustment

Adjustment Set

Knobs

1Blade

Guides

(Above and

Below Table)

t3 On-Off Switch

wlLockin 9Key 4Table Lock and

Adjustment

Knob

5 Tilt

Scale

13. On-Off Switch - The On-Off switch has a locking fea-

ture. This feature is intended to help prevent unautho-

rized and possible hazardous use by children and

others.

1. To turn band saw "On" insert key into switch.

NOTE: Key is made of yellow plastic, located in

loose parts bag.

2. Insert finger under switch lever and Pull end of

switch out.

3. To turn band saw "Off" Push lever in.

IWARNING: Never leave the band saw unattendeduntil it has come to a complete stop.

4. To lock switch in Off position hold switch in with one

hand and remove key with other hand.

WARNING" For your own safety, always lock the

switch "Off" when band saw is not in use, remove

the key and keep it in asafe place. In the event of a

power failure (all of your lights go out) turn switch

off, remove the key and store it away from the band

saw. This will prevent the machine from starting up

again when the power comes back on.

Safety Instructions for Basic Band Saw Operation

Before Using the Saw:

WARNING: to avoid mistakes that could cause seri-

ous, permanent injury, do not plug the saw in until

the following steps have been completed.

•Completely assemble and align saw (see "Assembly"

and "Alignment" section within).

• Learn the use and function of the ON-OFF switch,

table bevel and bevel lock knob, blade guides, backup

bearings, guide bar lock knob and blade guard.

• Review and understand all safety instructions and

operating procedures in this manual.

•Review the maintenance methods for this saw.

•Find and read all the warning labels found on the front

of the saw.

When Installing or Moving the Saw:

Avoid dangerous environment,

• Use the saw in a dry, indoor place protected from rain.

• Keep work area well lighted.

To avoid injury from unexpected saw movement.

• Put the saw on a firm level surface where there is

plenty of room to handle and properly support the

workpiece.

•Support the saw so the table is level and the saw does

not rock.

• Bolt the saw to the floor or work surface. Saw may slip,

walk or slide while cutting long or heavy boards.

•Turn saw off and unplug cord before moving the saw.

To avoid injury from electrical shock.

•Make sure your fingers do not touch the plug's metal

prongs when plugging in or unplugging the saw.

•Never stand on tool. Serious injury could occur if the

tool tips or you accidentally hit the cutting tool. Do not

store any items above or near the tool where anyone

might stand on the tool to reach them.

Before Each Use:

Inspect your saw.

• To avoid injury from accidental starting, turn the switch

off, unplug the saw, and remove the switch key before

changing the setup, removing covers, guards or blade.

• Check for alignment of moving parts, binding of moving

parts, breakage of parts, saw stability, and any other

conditions that may affect the way the saw works.

•If any part is missing, bent or broken in any way, or any

electrical part does not work properly, turn the saw off

and unplug the saw.

•Replace damaged or missing parts before using the

saw again.

•Maintain tools with care. Keep the saw clean for best

and safest performance. Follow instructions for lubri-

cating.

• Remove adjusting keys and wrenches. Form a habit of

checking for and removing keys and adjusting

wrenches from table top before turning it on.

To avoid injury from jams, slips or thrown pieces or

broken blades.

Inspect your blade.

•Choose the right blade size, style and cutting speed for

the material and the type of cutting you plan to do.

•Use only recommended accessories. Consult this

owners manual for recommended accessories. Follow

the instructions that come with the accessories. The

use of improper accessories may cause risk of injury to

persons.

•Make sure the blade teeth point downward, toward the

table.

•Make sure the blade guides and thrust bearings are

properly adjusted.

• Make sure the blade tension is properly adjusted.

•Make sure the bevel clamp is tight and no parts have

excessive play.

•To avoid accidental blade contact, minimize blade

breakage and provide maximum blade support, always

adjust the upper blade guide and blade guard to just

clear the workpiece.

Inspect your work area.

•Keep work area clean.

•Cluttered areas and benches invite accidents. Floor

must not be slippery from wax or sawdust.

• To avoid burns or other fire damage, never use the saw

near flammable liquids, vapors or gases.

Plan Your Work:

• Use the right tool. Don't force tool or attachment to do

a job it was not designed to do.

•Use this band saw to cut only wood, wood like prod-

ucts and plastics.

I CAUTION: To avoid blade breakage, fire or other I

damage to the saw, never use this band saw to cut I

metals.

•To avoid injury from accidental contact with moving

parts, don't do layout, assembly, or set up work on the

saw while any parts are moving.

• Avoid accidental starting. Make sure switch is "OFF"

before plugging saw into a power outlet.

•Plan ahead to protect your eyes, hands, face and ears.

Safety Instructions for Basic Band Saw Operation (continued)

Dress For Safety

• Any power saw can throw foreign objects into the eyes.

This can cause permanent eye damage. Wear safety

goggles (not glasses) that comply with ANSI Z87.1

(shown on package). Everyday eyeglasses have only

impact resistance lenses. They are not safety glasses.

Safety goggles are available at Sears retail stores.

Glasses or goggles not in compliance with ANSI Z87.1

could seriously hurt you when they break..

WEAR YOUR

• Do not wear loose clothing, gloves, neckties or jewelry

(rings, wrist watches). They can get caught and draw

you into moving parts.

• Wear nonslip footwear.

• Tie back long hair.

• Roll long sleeves above the elbow.

• Noise levels vary widely. To avoid possible hearing

damage, wear ear plugs or muffs when using saw for

hours at a time.

• For dusty operations, wear a dust mask along with the

safety goggles.

Inspect your workpiece.

Make sure there are no nails or foreign objects in the

part of the workpiece to be cut.

Use extra caution with large, very small or awkward

workpieces:

• Use extra supports (tables, saw horses, blocks, etc.)

for any workpieces large enough to tip when not held

down to the table top.

•Never use another person as a substitute for a table

extension, or as additional support for a workpiece that

is longer or wider than the basic saw table, or to help

feed, support or pullthe workpiece.

•When cutting irregularly shaped workpieces, plan your

work so it will not slip and pinch the blade. A piece of

molding for example, must lie fiat or be held by a fixture

orjig that will not let it twist, rock or slip while being cut.

•Properly support round material such as dowel rods, or

tubing. They tend to roll during a cut, causing the blade

to "bite". To avoid this, always use a "V" block or clamp

the work to the miter gage.

•Cut only one workpiece at a time.

•Clear everything except the workpiece and related

support devices off the table before turning the saw on.

Plan the Way You Will Hold the Workpiece

From Start To Finish.

•Do not hand hold pieces so small that your fingers will

go under the blade guard. Use jigs or fixtures to hold

the work and keep your hands away from the blade.

•Secure work. Use clamps to hold work when practical.

It's often safer than using your hand, and frees both

hands to operate the tool.

• Don't overreach. Keep good footing and balance.

Whenever Sawblade Is Moving:

WARNING: Don't allow familiarity (gained from fre-

quent use of your band saw) cause a careless mis-

take. Always remember that a careless fraction of a

second is enough to cause a severe injury,

•Before starting your cut, watch the saw while it runs. If

it makes an unfamiliar noise or vibrates a lot, stop

immediately. Turn the saw off. Unplug the saw. Do not

restart until finding and correcting the problem.

Keep children away.

• Keep all visitors a safe distance from the band saw.

•Make sure bystanders are clear of the band saw and

workpiece.

Don't force tool.

•Let the blade reach full speed before cutting.

•It will do the job better and safer at its designed rate.

• Feed the workpiece into the saw only fast enough to let

the blade cut without bogging down or binding.

Before freeing jammed material,

•Turn switch "OFF".

•Unplug the saw.

• Wait for all moving parts to stop.

•Remove switch key.

When backing up the workpiece, the blade may bind

in the kerf (cut). This is usually caused by sawdust

clogging up the kerf or because the blade comes out

of the guides. If this happens:

• Turn saw "OFF".

• Wait for all moving parts to stop.

•Remove switch key.

•Unplug the saw.

• Remove band saw cover.

•Stick fiat blade screwdriver or wedge into the kerr.

•Turn the upper wheel by hand while backing up the

workpiece.

Before removing loose pieces from the table, turn saw off

and wait for all moving parts to stop.

Before Leaving the Saw.

•Turn the saw off.

•Wait for all moving parts to stop.

•Unplug the saw.

• Make workshop child-proof.

- Lock the shop.

- Disconnect master switches.

-Remove the yellow switch key. Store it away from

children and others not qualified to use the tool.

Basic Band Saw Operations

General Cutting

ICAUTION: For your safety, comply with all the l

safety instructions in "Safety Instructions for Band J

Saw" section before using the band saw.

A band saw is a "curve cutting" machine.

It is also used for straight-line cutting operations such as

crosscutting, ripping, mitering, beveling, compound cut-

ting and resawing.

Operation Recommended Blade Size

(Inches)

Cross Cutting 1/4, 3/8

Ripping 3/8

Mitering 114,318

Beveling 1/4,3/8

Compound Cutting 1/4,3/8

Circle Cutting See Below

Resawing 3/8

Curve Cutting 1/4, 1/8

Circle Cutting

1. Adjust the upper guides to vertically clear the work-

piece by approximately 1/8".

2. Use both hands while feeding the work into the blade.

Hold the workpiece firmly against the table. Use gentle

pressure, and do not force the work, but allow the

blade to cut.

3. The smallest diameter that can be cut out is deter-

mined by the width of the blade. For example, a 1/4-

inch wide blade will cut a minimum diameter of approx-

imately 1-1/2-inch. A1/8" blade will cut a minimum

diameter of 1/2".

Relief Cuts

Relief cuts are made when an intricate curve (too small a

radius for the blade) is to be cut. A relief cut is made by

cutting through the scrap section of workpiece to curve in

pattern line, then carefully backing blade out. Several

relief cuts should be made for intricate curves, then follow

pattern line as sections are cut off curve "relieving" blade

pressure.

NOTE: Blade guard is raised and right hand moved for

clarity of picture only.

Pattern Line

Workpiece

Relief Cuts

Maintenance

IWARNING: For your own safety, turn switch "Off" I

and remove plug from power source outlet before I

maintaining or lubricating your band saw,

Maintenance

IDANGER: Never put lubricants on the blade while it I

is spinning. I

I WARNING: To avoid injury from unexpected start- I

ing or electrical shock, unplug the power cord I

before workinq on the saw.

Tires

General Maintenance

Keep your band saw clean. Remove the sawdust from

the inside. Vacuum or blow out saw frequently.

Do not allow filth to build up on the table the guides or the

back-up bearings. Clean them with Craftsman Gum and

Pitch Remover.

NOTE: Do not immerse the back-up bearings in the gum

and pitch remover.

Put athin coat of paste wax on the table so that the wood

slides easily while cutting.

Motor

Pitch and sawdust that build up on the tires should be

removed with a stiff brush or scraped with a piece of

wood.

NOTE: To avoid damaging the tires do not use a sharp

knife or any kind of solvent.

When the tires become worn they should be replaced.

When replacing the tires, stretch them around the wheels

but do not glue them on.

Frequently blow or vacuum out any sawdust from the

motor. Follow lubrication instruction on the motor label.

I CAUTION: To avoid eye injury from blowing debris, I

wear safety goggles when blowing out sawdust.

I WARNING: To avoid electrocution or fire, immedi- I

ately replace a worn, cut or damaged power cord.

Lubrication

All of the ball bearings are packed with grease at the fac-

tory. They require no further lubrication.

Sears Recommends the Following Accessories

IWARNING: To avoid injury from unsafe accesso-

ries, use only accessories shown on the recom-

mended accessories list in this manual.

Miter Gauge ........................................................ 9-24214

Blades (59-1/4" length) .............................. See Catalog

Leg Set ............................................................... 9-22244

Power Tool handbook.................... 9-29114 and 9-29115

Sears may recommend other accessories not listed in

the manual. See your nearest Sears store for other

accessories.

Prohibited Accessories

Do not use any accessory unless you have received and

read complete instructions for its use.

Troubleshooting

WARNING: For your own safety, turn switch "Off" and remove plug from power source outlet before trouble

shooting your band saw/sander.

General

Trouble Probable Cause Remedy

Blade does not run in the 1. Not tracking properly. 1. Adjust tracking, see Alignment section, "Tracking the

approximate center of the Blade".

upper wheel.

Band Saw slows when cut-

ting

Blades breaking

Blade dulls too quickly.

Band saw vibrates.

1. Belt too loose.

2. Cutting too small a radius.

3. Dull blade.

4. Overloading motor.

Too much tension on

blade.

Kink in blade caused by

cutting too small a radius

or turning the material too

fast when cutting.

1. Blade guides set too close

to teeth.

2. Cutting incorrect material

1. Too much tension on

motor belt

1. Adjust belt tension, see "Alignment section, "Adjust-

ing Motor Belt".

2. Stop feeding, and pull the material away from the

blade until the band saw returns to normal speed.

3. Replace blade.

4. Slow down, trying to cut too fast.

1. Adjust tension. See "Alignment section, "Tensioning

the Blade".

2. Use correct cuttingtechnique. See "Basic Band Saw

Operation" section.

1. Adjust upper and lower blade guides. See "Align-

ment" section "Adjusting the Blade Guides and Back-

up Bearing".

1. Adjust according to "Adjusting Motor Belt" sec-

tion.

CAPACITOR

RED

WHITE Z_ POWER CORD

WHITE

BLACK BLACK

GREEN

GROUND SCREW

Circuit Diagram

Motor

NOTE: Motors used on wood-working tools are particularly susceptible to the accumulation of sawdust and wood chips

and should be blown out or "vacuumed" frequently to prevent interference with normal motor ventilation and proper

operation of the centrifugally-operated starting switch.

Trouble Probable Cause Remedy

Excessive noise 1. Motor 1. Have motor checked by qualified service tech-

nician. Repair service is available at your near-

est Sears store.

Motor fails to develop full

power. Note Low Voltage:

Power output of motor

decreases rapidly with

decrease in voltage at

motor terminals. For

example, a reduction of

10% in power cord line

voltage causes a 19%

reduction in maximum

motor power output. A

20% reduction in power

cord line voltage causes a

36% reduction in maxi-

mum motor power output.

Motor starts slowly or fails

to come up to full speed.

Motor overheats

Starting switch in motor

will not operate.

Motor stalls (resulting in

blown fuses or tripped cir-

cuit breakers).

Frequent opening of fuses

or circuit breakers.

1. Circuit overloaded with light,

appliances and other motors.

2. Undersize wires or circuit too

long.

3. General overloading of power

company facilities.

1. Low voltage.

2. Windings burned out or open.

3. Starting switch not operating.

Motor overloaded.

Improper cooling (air circula-

tion restricted through motor

due to sawdust accumulation).

1. Burned switch contacts (due to

extended hold-in periods

caused by low line voltage,

etc.)

2. Shorted capacitor.

3. Loose or broken connections.

1. Starting switch not operating.

2. Voltage too low to permit motor

to reach operating speed.

3. Fuses or circuit breakers do

not have sufficient capacity.

1. Motor overloaded.

2. Fuses or circuit breakers do

not have sufficient capacity.

3. Starting switch not operating

(motor does not reach speed).

1. Do not use other appliances or motors on

same circuit when using the saw.

2. Increase wire sizes, or reduce length of wiring.

See "Motor specifications and Electrical

Requirements" section.

3. Request a voltage check from the power com-

pany.

1. Request voltage check from the power com-

pany. Check size of circuit wiring.

2. Have motor repaired or replaced.

3. Blow out sawdust from motor. Have motor

repaired.

Feed work slower into blade.

Clean out sawdust to provide normal air circu-

lation through motor. See "Maintenance" sec-

tion.

Have switch replaced and request a voltage

check from the power company.

2. Have capacitor tested and replace if defective.

3. Have wiring checked and repaired.

1. Have switch replaced.

2. Request voltage check from the power com-

pany.

3. Install proper size fuses or circuit breakers.

1. Feed work slower into blade.

2. Install proper size fuses or circuit breakers.

Check that wiring will handle load.

3. Have switch replaced. Blow out sawdust.

\52

Parts List For Craftsman 9-inch Band Saw

Model No. 113.244580

Figure I

38' 39

// 63

4_ 48

38 37

8 9 10 11

7 I /l_J

It_tt

9 1011

24 25

::o

tJ!

Key

No.

Parts List For Craftsman 9 Inch Band Saw Model No. 113.244580

Always Order By Part Number- Not By Key Number

Figure I -Drive Assembly Parts

Part No.

824042

STD551031

824041

824040

824085

806036-1

824059

824060

824061

STD551025

824072

824082

824056

821555

813989-1

824073

iSTD523110

STD551131

824075

824083

824079

824078

824068

824070

824071

STD541025

STD541625

60530

824074

824144

STD541031

1824069

1824065

820265

STD522507

STD551125

824063

824062

Description

Knob Tension

* Washer 21/64 x 47/64 x 1/16

Spring Tension

Cover Knob

Frame

Screw Set Oval 1/4-20 x 5/8

Shaft Gear

Knob Drive

Spring Knob

* Washer 1/4 x5/8 x 1/16

Knob Lock

Screw Pan Hd. 3/16-24 x 3/8

Plate Cover

Relief Strain

Cord w/Plug

Motor

* Screw Hex hd. 5/16-18 x 1

* Lockwasher 5/16

Screw Flat Hd. 1/4-20 x 24mm

Table

Washer Spring

Screw Shoulder Washer Hd. 1/4-20

Trunnion

Shaft Trunnion Lock

Knob Table Tilt

*Nut Hex 1/4-20

*Nut Wing 1/4-20

Screw Truss Hd. 1/4-20 x 3/4

Insert Table

Pulley Motor

*Nut Hex 5/16-18

Indicator Bevel

Screw Cap 3/16-24 x 1/2

Foot Frame

* Screw Hex Hd. 1/4-20 x 3/4

*Lockwasher 1/4

Block Guide

Support Guide Block

Standard hardware item. May be purchased locally.

Key Part No. Description

No.

39 824064

40 824033

41 824045

42 824081

43 822308

44 824055

45 9-22255

46 820274

47 824096

48 824030

49 824031

50 824028

51 824023

52 824048

53 820248-2

54 STD851012

55 817453-2

56 824052

57 824053

58 824051

59 !824049

805606-20

824077

STD315505

824035

824076

STD512505

824039

824036

STD541431

824058

824066

805594-10

824057

37887

SP5872

Block Guide

Belt

Brush Lower

Screw Seres M4 x 6

Switch Locking

Cover Switch

1-Key Switch

Capacitor 16MFD

Brush Upper

Shaft Lower Wheel

Pulley Idler

Tire Wheel

Wheel Lower/Includes Key # 50

Blade 59-1/4

Screw Pan Hd. Ty AB M4.2 x 1.4-8

* Washer M12

Ring Retaining

Pin Cover

Spring Cover

Latch Cover

Cover (Includes Keys 56, 57 & 58

Ring Retaining

Washer Plastic

Bearing Ball 6000Z

Wheel Upper

Shaft Upper Wheel

Screw Pan Hd. 1/4-20 x 1/2

Plate

Support Upper Wheel

Nut Lock 5/16-18

Guard Upper Blade

Bearing Thrust

Bolt Carriage 1/4-20 x 2-3/4

Slide Upper

Wrench Hex "L" 1/8

Owners Manual (Not Illustrated)

1- Stock Item - May be secured through the Hardware

Department of most Sears Retail Stores.

Notes

SEARS

owner's

manual

Model No.

113.244580

Two Wheel

9 Inch Band Saw

The model number of your

band Saw will be found on a

plate attached to your saw, at

the left-hand side of the base

When requesting service or

ordering parts, always provide

the following information:

•Product Type

• Model Number

•Part Number

• Part Description

TWO WHEEL

9 INCH BAND SAW

For the repair or replacement parts youneed

Call 7am - 7 pro, 7days a week

1-800-366-PART

(1-800-366-7278)

For in-home major brandrepair service

Call 24 hours aday, 7 daysaweek

1-8OO-4-REPAIR

(1-800-473-7247)

For the location of a

SearsRepair Service Center in yourarea

Call 24 hoursaday,7daysaweek

1-800-488-1222 In|Ill

lummlu

For information onpurchasinga Sears

Maintenance Agreementor to inquire

about an existing Agreement

Call 9 am -5 pm, Monday-Saturday

1-800-827-6655

SEARS

I;ttl_fl;tg$gt;trl[t,]_l

America's Repair Specialists

Part No. SP5872

Sears, Roebuck and Co., Chicago, IL. 60179 U.S.A.

Form No SP5872 Printed in Taiwan 7/95

Craftsman 113244580 User Manual TWO WHEEL 9 BAND SAW Manuals And Guides L0910140

CRAFTSMAN Saw Band Manual L0910140 CRAFTSMAN Saw Band Owner's Manual, CRAFTSMAN Saw Band installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation