Craftsman 11329570 User Manual 10 INCH MOTORIZED SAW Manuals And Guides L0807115

CRAFTSMAN Saw Table Manual L0807115 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

User Manual: Craftsman 11329570 11329570 CRAFTSMAN CRAFTSMAN 10 INCH MOTORIZED SAW - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 10 INCH MOTORIZED SAW #11329570. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 10 INCH MOTORIZED SAW Manual

Open the PDF directly: View PDF .
Page Count: 40

ISears]

owners

manual

MODEL NO.

113.29570

SAW ONLY

113.295750

SAW WITH LEGS AND

TWO TABLE EXTENSIONS

Serial

Number .......

Model and serial

number may be found

at the right-hand side

of the base.

You should record both

model and serial number

in a safe place for

future use,

CAUTION:

Read GENERAL

and ADDITIONAL

SAF ETY

INSTRUCTIONS

carefully

CRAFTSMAN°

IO-INCH MOTORIZED

TABLE SAW

•assembly

•operating

•repair parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part No. 62716 Printed in U_S.A.

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWS

If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or

workmanship, Sears will repair it. free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE

OR SERVICE CENTER THROUGHOUT THE UNITED STATES,

This warranty gives you specific legal rights, and you may also have other rights which vary from state to

state,

SEARS. ROEBUCK AND CO.. Sears Tower. BSC 41-3. Chicago, ]L 60664

general safety instructions for power tools

1. KNOW YOUR POWER TOOL

Read the owner's manual carefull,_. Learn ts

aoDlication and limitations as well as the specific

potenttal hazards peculiar to this tool 13.

2. GROUND ALL TOOLS

Th ; tool sequipped with an approved 3*conductor

coro and a 3*prong grounding tvoe plug Io fit the 14.

Drouer grounamg [yDe receptacle. The green conauctot

'n me cord _s the grounding w_re. Never connect the

green wire to a live terminal 15.

adjustment and

3. KEEP GUARDS IN PLACE

n working order, and n proper

alignment.

4. REMOVE ADJUSTING KEYS

AND WRENCHES

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on,

5. KEEP WORK AREA CLEAN

Cluttered areas and benches mvite accidents. Floor

must not be slippery clue to wax or sawdust.

6. AVOID DANGEROUS ENVIRONMENT

Don't use power tools in damp or wet {ocations or

protectors (plugs or muffs] during extended periods of

operation.

SECURE WORK

Use clamos or a vise to hold work when practical, t's

safer than using your hand. frees both hands to operate

tool

DON'T OVERREACH

Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE

Keen tools sharp and clean for oest and safest

performance. Follow instructions for lubricating and

changing accessories

16. DISCONNECT TOOLS

before serv=cmg; when changing accessoHes such as

blades, bits. cutters etc

17. AVOID ACCIDENTAL STARTING

Make sure switch is 'n OFF poston before plugging

in.

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended

accessories. Follow the instructions that accompany

expose them to rain. Keep work area well lighted, the

Provide adequate surrounding work space, accessories. The use of improper accessories may

Cause hazards.

7. KEEP CHILDREN AWAY i9 NEVER STAND ON TOOL

AII visitors should be kept a safe distance f_om Work _ ....

area. benous Injury eou d occur if the to01 is tipped or if the

cutting tool is accidentally contacted.

8. MAKE WORKSHOP KID-PROOF Do not store materials above or near the tool such that

- with padlocks, master switches, or by removing

starter keys.

9. DON'T FORCE TOOL ....

It will do the job better and safer at the rate for which

it was designed.

10. USE RIGHT TOOL

Don't force tool or attachment to do a job it was not

designed for.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves, neckties or jewelry

(rings, wrist watches) to get caught in moving parts.

Nonslip footwear is recommended. Wear protective

hair covering to contain long hair. Roll long sleeves

above the elbow

12. USE SAFETY GOGGLES (Head ProtectiOn)

Wear Safety goggles (must comply with ANSI Z87.1)

at all times. Everyday eyeglasses only have impact

resistant lenses, they are NOT safety glasses. Also, use

face or dust meal( if cutting operation is dusty; and ear

it is necessary to stand on the tool to reach them.

20, CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that

is damaged should be carefully checked to ensure that it

witl operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other

conditions that may .affect its operation. A guard or

other part that is damaged should be properly repaired

or replaced.

21. DIRECTION OF FEED .....

Feed work into a blade or cutter against the direction

of rotation of the blade or cutter only.

22, NEVER LEAVE TOOL RUNNING

UNATTENDED

Turn power off. Don't leave tool until it comes to a

complete stop.

ADDITIONAL SAFETY INSTRUCTIONS

FOR TABLE SAWS

WARNING: FOR YOUR OWN SAFETY, DO NOT

OPERATE YOUR SAW UNTIL IT IS COMPLETELY

ASSEMBLED AND INSTALLED ACCORDING TO THE

INSTRUCTIONS ... AND UNTIL YOU HAVE READ

AND UNDERSTOOD THE FOLLOWING.

1GENERAL SAFETY INSTRUCTIONS FOR POWER

TOOLS... SEE PAGE 2

2. GETTING TO KNOW YOUR SAW... SEE PAGE 15

3, BASIC SAW OPERATION... SEE PAG E 17

4, ADJUSTMENTS... SEE PAGE 23

5. MAINTENANCE... SEE PAGE 26

6. STABILITY OF SAW

If there _sany tendency for the saw to tio over or move

during certain cutting operations such as cutting

extremely large heavy panels or long heavy boards, the

sawshould be bolted down.

If you attach any kind of table extensions over 24"

wide to either end of the saw, make sure you either

bolt the saw to the bench or floor as appropriate, or

support the outer end of the extension from the bench

or floor, as appropriate.

LOCATION

The saw should be aositioned so neither the ooerator

nor a casual observer is forced to stand in hne with the

saw blade.

8. KICKBACKS

Kickbacks can cause serious injury: A "KICKBACK'"

occurs when a part of the workplece binds between the

sawblade and the rip fence or other fixed object, rises

from the table, and is thrown toward the operator,

<eeD your face and body to one side of the sawblade,

out of line with a possible "Kickback.'"

Kickbacks - and possible injury from them can

usually be avoided by:

A, Maintaining the rip fence paragel to the sawblade.

B. Keeping the sawblade sharp. Replacing antikickback

pawls when points become dull.

C. Keeping sawblade guard, spreader, and antikickback

pawls in place and operating properly. The spreader

must be in alignment with the sawblade and the

pawls must stop a kickback once it has started.

Check their action before ripping.

D. NOT ripping work that is twisted or warped or does

not have a straight edge to guide along the rip fence,

E. NOT releasing work untiI you have pushed it all the

way past the sawbiade.

F. Using a"PUSH STtCK" (See Page 16) for ripping

widths of 2 to B in., and an auxiliary fence and push

block for ripping widths narrower than 2 in. (See

"Basic Saw Operation UsJngTbe Rip Fence" section.)

G. NOT confining the cut-off piece when ripping or

crosscutting,

H. When ripping apply the feed force to the section of

the workpiece between the saw blade and the rip

fence.

9. PROTECTION: EYES, HANDS, FACE, EARS, BODY

A. If any part of your saw is malfunctioning, has been

damaged or broken.., such as the motor switch, or

orher operating contlol, a safety d_vice or the

power cord ,., cease operating immediately until

the particular part is properly repaired or replaced.

B. Wear safety goggles that comply with ANSI Z87.1,

and a face shield if operation is dusty. Wear ear

plugs or muffs during extended periods of

operation.

C. Small loose pieces of wood or other objects that

contact the rear of the revolving blade can be

thrown back at the operator at excessive speed. This

can usually be avoided by keeping the guard and

spreader n glace for all "THRU-SAWING"

operations (sawing entirely thru the work) AND by

remowng all loose pieces from the table with along

stick of wood IMMEDIATELY after they are cut

off.

Use extra caution when the guard assembly is

removed for resawmg, dadoing, rabbeting, or

molding -- replace the guard as soon as that

operation is completed,

NEVER turn the saw "ON" before clearing the

table of all tools, wooa scraos, etc,, except the

workpiece and related feed or support devices _for

the operation planned.

NEVER place your face or body in line with the

cutting tool.

NEVER place vour fingers or hands in the path of

the sawblade or other cutting tool.

NEVER reach in back of the cutting tool with

either hand to hold down or support the workplace,

remove wood scraos, or for any other reason. Avoid

awkward operations and hand positions where a

sudden slip could cause fingers or hand to move

into a sawolade or other cutting tool.

I. DO NOT perform any operation "FREEHAND'"

alwa_,,s use either the np fence or the miter gauge to

oosition and guide the work.

J, NEVER use the rip fence when crosscutting or the

miter gauge when ripping. DO NOT Jse the rip

fence as a length stop.

Never hold onto or touch the "free end" of the

workpiece or a "'free piece*' that is cut off, while

power is "ON" and/or the sawblade is rotating.

K. Shut "OFF" the saw and disconnect the power cord

when removing the table insert, changing the

cutting tool, removing or replacing the blade guard,

or making adjustments.

L. Provide adequate support to the rear and sides of

the saw table for wider or long workpieces.

M. Plastic and composition (like hardboard) materials

may be cut on your saw. However, since these are

usually quite hard and slippery, the antikickback

pawls may not stop a kickback.

Therefore, be especially attentive to following

proper set-up and cutting procedures for ripping.

Do not stand, or permit anyone else to stand, in line

with a potential kickback.

N. DO NOT perform layout, assembly, or setup work

on the table while the cutting tool is rotating.

O. If you stall or jam the sawblade in the workpiece,

turn saw "OFF", remove the workpiece from the

sawblade, and check to see if the sawblade is

parallel to the miter gauge grooves and if the

spreader is in proper alignment with the sawblade.

If ripping at the time, check to see if the rip fence is

parallel with the sawblade. Readjust as indicated.

10. KNOW YOUR CUTTING TOOLS

A Dul!, gummy, or improperly sharpened or" set cutting

tOOIS can cause material to stick, jam, stall the saw,

or kickback at the operator.

Minimize potential injury by proper cutting tool

and machine maintenance.

NEVER ATTEMPT TO FREE A STALLED

SAWBLADE WITHOUT FIRST TURNING THE

SAW OFF.

B. Never use grinding wheels, abrasive cut-off wheels,

friction wheels (metal slitting blades) wire wheels or

buffing wheels,

11. USE ONLY ACCESSORIES DESIGNED FOR THIS

SAW.

12, Crosscutting operations are more conveniently worked

and with greater safety f an auxiliary wood facing is

attached to the miter gauge using the holes provided.

However. the facing must not interfere with the proper

functioning of the sawbtade guard.

13. Make sure the top of the arbor or cutting tool rotates

toward you when standing ir normal operating

aosition. Also make sure the cutting tool, arbor collars

and arbor nut are installed properly. Keep the cutting

tool as Fow as possible for the operation being

performed. Keep all guards in place whenever possible.

14. Do not use any blade or other cutting tool marked for

an operating speed less than 3450 RPM. Never use a

cutting tool larger in diameter than the diameter for

which the saw was designed. For greatest safety and

efficiency when ripping, use the maximum diameter

blade for which the saw is designed, since under these

conditions the spreader is nearest the blade,

15. Adjust table inserts flush with the table top. NEVER

Operate the saw unless the _roper insert is installed.

16. Never feed material into the cutting tool from the rear

of the saw. An accident and serious injury could result.

17. THINK SAFETY.

Safety is a combination of operator common senseand

alertness at all times when the saw is being used,

18. NOTE AND FOLLOW SAFETY INSTRUCTIONS

THAT APPEAR ON THE FRONT OF YOUR SAW,

DANGER

FOR YOUR OWN SAFETY

READ AND UNDERSTAND OWNER'S MANUAL

BEFORE OPERATING MACHINE:

1. WEAR SAFETY GOGGLES

2. USE SAW-BLADE GUARD FOR "THRU-SAWING"

3. KEEP HANDS OUT OF PATH OF SAWBLADE

4. USE A "PUSH-STICK" WHEN REQUIRED

5. KNOW HOW TO AVOID "'KICKBACKS'"

6. DO NOT PERFORM OPERATI ONS "FREEHAND"

7. NEVER REACH AROUND OR OVER SAW BLADE

19. WARNING: DO NOT ALLOW FAMILIARITY

(GAINED FROM FREQUENT USE OF YOUR SAW)

TO BECOME COMMONPLACE. -ALWAYS

REMEMBER THAT A CARELESS FRACTION OF A

SECOND IS SUFFICIENT TO INFLICT SEVERE

INJURY.

WEAR YOUR

The operation of any power tool can result in foreign

objects being, thrown into the eyes, which can result m

severe eye damage. Always wear safety goggles complying

with ANSI Z87.1 (shown on Package) before commencing

power tool operation. Safety Goggles are available at Sears

retail or catalog stores.

MOTOR SPECIFICATIONS AND

ELECTRICAL REQUIREMENTS

MOTOR SPECI FICATIONS

The AC motor used in this saw is acapacitor start,

non-reversible type, with the following specifications:

Voltage ................................. 120

Amperes ................................. 12

Hertz .................................. 60

Phase ............................... Single

RPM ................................. 3450

Rotation (viewec[ from

Sawblade end) .............. Counterclockwise

MOTOR SAFETY PROTECTION

The saw motor is equipped with a manual-reset thermal

overload protector, designed to open the power line circuit

when the motor temperature exCeeds a safe value.

NOTE: The starting relay is a GRAVITY SENSITIVE

TYPE. NEVER TURN THE POWER ON WHILE THE SAW

IS UPSIDE DOWN AS THiS WILL DAMAGE THE

MOTOR

1, If the protector opens the line and stops the saw motor,

move the saw switch lever to the "OFF" position

immediately and allow the motor to cool.

2. After cooling to a safe operating temperature, the

overload protector can be closed manually by pushing

in the red RESET button on the front of the saw. If the

red I_utton Will not snag into place immediately, the

motor is still too hot and must be allowed to coo! for a

while longer.

3. As soon as the red button wi snap into running

position, the saw may be started and operated normally

by moving the saw switch lever to the "ON" position.

4. Frertuent opening of fuses or circuit breakers may result

if motor is overloaded, or if the motor circuit is fused

with a fuse other than those recommended, Do not use

a fuse of greater capacity without consulting the power

company,

5Although the motor is designed for operation on the

voltage and frequency specified on motor nameplate,

normal loads will be handled safely on voltages not

more than 10% above or below the maneplate voltage.

Heavy loads, however, require that voltage at motor

terminals by no_ less than the voltage specified oll

nameplate.

6. Most motor troubles may be tracec to loose or

incorrect connections, overloading, reduced input

voltage (which results when small size wires are used i=_

the supply circuit} or when the supply circuit is

extremely long. Always check connection, load and

supply circuit when the motor fails [o aertorrn

satisfactorily. Check wire sizes and lengths with table at

end of this section.

CONNECTING TO POWER SOURCE OUTLET

This saw must be grounded while in use to protect the

operator from electrical shock.

If power cord is worn or cut, or damaged in anv way,

have it replaced immediately.

"If yoursawis for useon lessthan 150 volts it has a plug

that looks like below.

3-PRONG PLUG

\GROUNDING PRONG

PROPERLY GROUNDED

3-PRONG OUTLET

If the outlet you are planning to use for this saw is of the

two prong type DO NOT REMOVE OR ALTER THE

GROUNDING PRONG IN ANY MANNER. Use an adapter

as shown and always connect the groundi.g lug to a known

ground.

It is recommended that you have aqualified electrician

replace the TWO prong outlet with a properly grounded

THREE 10rongoutlet.

An adapter asshown below is available for conne_ing plugs

to 2-prong receptacles, The green grounding lug extending

from the adapter must be connected to a permanent ground

such asto aproperly grounded outlet box.

Plug power cord into 110-120V properly grounded type

outlet protected by a 1S-amp. time delay or Circuit-Saver

fuse or circuit breaker.

IF YOU ARE NOT SURE THAT YOUR OUTLET IS

PROPERLY GROUNDED, HAVE IT CHECKED BY A

QUALI FlED ELECTRICIAN.

WARNING: DO NOT PERMIT FINGERS TO TOUCH

THE TERMINALS OF PLUG WHEN INSTALLING OR

REMOVING THE PLUG TO OR FROM THE OUTLET,

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK, PARTICULARLY WHEN

USED IN DAMP LOCATIONS: IN PROXIMITY TO

PLUMBING, OR OUT OF DOORS. IF AN ELECTRICAL

SHOCK OCCURS THERE IS THE POTENTIAL OF A

SECONDARY HAZARD SUCH AS YOUR HANDS

CONTACTING THE SAWBLADE.

This saw is equipped with a 3_conductor cord and

grounding type plug which hasa grounding prong, approved

by Underwriters' Laboratories and the Canadian Standards

Association, The ground conductor has a green lug and is

attached to the toot housing at one end and to the ground

prong in the attachment plug at the other end.

This plug requires a mating 3-conductor grounded type

outlet asshown.

GROUNDING LUG

ADAPTER

MAKE SURE THiS iS

3-PRONG CONNECTED TO A

PLUG KNOWN GROUND

2-PRONG

RECEPTACLE

NOTE: The adapter illustrated {sfor use only if you already

have a properly grounded 2-prong receptacle.

The use of any extension cord will cause some loss of

power. To keep this to a minimum and to prevent

over-heating and motor burn-out, use the table below to

determine the minimum wire size (A.W.G.) extension cord.

Use only 3 wire extension cords which have 3 prong

grounding type plugs and 3-pole receptacles which w_ll

accept the plug on the saw.

Extension Cord Length Wire Size A,W.G.

Upto 100 Ft ...................... 12

100 - 200 Ft ....................... 10

200 - 400 Ft ......................... 8

CONTENTS

WARRANTY ................................. 2

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS ................. _....... 2

ADDITIONAL SAFETY INSTRUCTIONS

FOR TABLE SAWS ........................... 3

MOTOR SPECIFiCATiONS AND ELECTRICAL

REQUIREMENTS ............................ 4

UNPACKING AND CHECKING CONTENTS ........ 6

Tools Needed ................................ 6

List of Loose Parts ............................ 6

ASSEMBLY .................................. 7

Installing Elevation and Tilt Handwheels ........... 7

Checking Table Insert ......................... 7

Checking Blade Squareness to Table .............. 8

Checking Blade Elevation ...................... 8

Attaching Table Extensions ..................... 8

Installing Rip Fence Guide Bars .................. g

Assembling Steel Legs ........................ 10

Mounting Saw .............................. 10

Aligning Table Extensions ..................... 11

Aligning Rip Fence .......................... If

Installing Blade Guard ........................ 13

GETTING TO KNOW YOUR SAW ............... 15

On-OffSwltah .............................. 15

Reset Button ............................... 16

Elevation Handwheel ......................... 16

Tilt Handwheel ............................. 16

Rip Fence ................................. 16

Miter Gauge ................................ 16

Blade Guard ................................ 16

Table Insert ................................ 16

Removingand InstallingSawblade ............... 17

BASIC SAW OPERATION USING THE MITER GAUGE 17

Work Helpers ............................... 17

Crosscutting ................................ 18

Repetitive Cutting ........................... lg

Miter Cutting ............................... 20

Bevel Crosscutting ........................... 20

Compound Miter Cutting ...................... 2(]

BASIC SAW OPERATION USING THE RIP FENCE .. 20

Ripping ................................... 21

Bevel Ripping .............................. 21

Rasaw_ng .................................. 22

Cutting Panels .............................. 23

Rabbeting ................................. 23

ADJUSTMENTS .............................. 23

Miter Gauge ................................ 23

Heeling Adjustment or Parallelism of

Sawblade to Miter Gauge Groove ............... 24

Blade Tilt, or Squareness of

Blade to Table ............................. 2,$

Blade Elevation ............................. 26

Tilt and Elevation Mechanism .................. 26

MAINTENANCE ............................. 26

LUBRICATION .............................. 2'7

RECOMMENDED ACCESSORIES ................ 27

TROUBLE SHOOTING ........................ 2,g

REPAIR PARTS .............................. 30

UNPACKING AND CHECKING CONTENTS

z//_ TOOLS NEEDED

Hammer Medium Screwdriver

Small Sorewdriver

112in. 9116in.

Combination Square 3/4 in.

COMBINATION SQUARE MUST BE TRUE.

S_AIGHT EDGE OF _,)ARD

3/4 THICK. THIS EDG_ MUST

DRAW LIGHT LiNE ON BE PERFECTLY STRAIGHT.

ROARD ALONG I'HIS EDGE* ¢_\

SHOULD BE NO 3AP OF OVERLAp

4ERE WHEN SQUARE {S FLII=PED

OVER {N DOTTED POSITION.

Model t13.29570 Motorized Table Sew is shipped complete

in one carton but DOES NOT INCLUDE Table Extensions

and Steel Legs.

Model 113.295750 Motorized Table Saw is shipped

complete in one carton but INCLUDES TWO Table

Extensions and Steel Legs.

Separate all parts from packing materials and check each

one with the illustration and the list of Loose Parts to make

certain all items are accounted for, before discarding any

packing material,

If any parts are mtssing, do not attempt to assemble the

table saw, plug in the power cord or turn the switch on

until the missing parts are obtained and are installed

correctly.

A B

jH G

WARNING: FOR YOUR OWN SAFETY, NEVER

CONNECT PLUG TO POWER SOURCE OUTLET UNTIL

ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU

HAVE READ AND UNDERSTAND THE SAFETY AND

OPERATIONAL INSTRUCTIONS.

LIST OF LOOSE PARTS

Key

No. PartName Qty,

AMiterGauge ..............................1

BRip Fence ............................... 1

CBladeGuardand Spreader ................... 1

D Handwheel............................... 2

E Rip FenceGuideBar, Rear .................. 1

F Rip FenceGuideBar Rod ................... 1

G Rip FenceGuideBar with RipScale(Freut) ..... 1

H ArborWrench ............................ 1

J Arbor Nut Wrench ......................... 1

KOwnersMenuat .......................... 1

Pkg.of MiscellaneousSmall PartsNo. 627!7

Consistingof the Following:

L SpreaderSupport .......................... 1

M SpreaderClamp ........................... 1

N SpreaderBracket ......................... 1

P SetscrewWrench,l/Sin ..................... 1

P SetscrewWrench,3/16 in.................... 1

Q SwitchKey ..............................2

R GuideBar Spacer .......................... 2

SSoc, Hd.Set ScrewI/4-20 x7/8 .............. 2

T SquareNut, 1/4-20 ........................ 2

U SelfThreadingNut ........................ 2

V Flatwasher,(die,of hole 17/64 in.) ............ 4

V Flatwasher,(dia. of hole 21/64 in.) ............ 4

W Hex Nut, 1/4-20

{Approx.dia. of hole 1/4 in.) ............... 2

W HexNut, 5/16-18

(approx.die. of hole5/16 in.) ............... 4

XLockwasher,1/4 in. ExternalType

{approx.die,of hole1/4 in,] ............... 4

X Lockwasher,5/16 in. ExternalType

(approx.dia. of hole5/16 in.) ............... 4

XLuckwashar-#10 ExternalType

(approx.die.of hole3/18 in.) ............... 2

Y WingScrew, 1/4-20 x 1/2 {n.long ............. 2

ZRex Hd. Screw, 5/16 - 18 x 1-1/2 im long ....... 2

Z Hex Hd,Screw,5/16 - f8 x 1 in. tong .......... 2

AA Screw,Pro1Hd. 10-32 x 3/4 .................. 2

The following parts are included with Model 113.295750

Key

No. Part Name Qty.

A Leg ..................................... 4

BSideStiffener ............................. 2

C EndStiffener ............................. 2

I1 Table Extension ........................... 2

Pkg.of Misce!laneousSmall Parts,No. 62659

Consistingof the Following:

EHex HeadScrew5/16--18 x 1-1/4 in. long ..... 6

FLockwashsr,1/4 in. ExternalType

(appmx. dia, of hole1/4 in.) .............. 24

FLeckwasher,5/16 in. ExternalType

(approx.dia.of hole 5/16 in.) ............. 6

G HexNut, 1/4-20

(approx.dia.of hole1/4 in.) .............. 24

G HexNut, 5/16-]8

(approx.die.of hole5/16 in.) ............. S

G Hex Nut, 1/2-13

(approx, die.af hole1/2 in.) .............. 8

III

H FlatWasher(dia, of hole, 11/32 in.) .......... 6

J TrussHeadScrew,1/4-20 x 5/8 in. long

(top of screwis rounded) ................. 24

K LevelingFoot ..... . ..................... 4

ASSEMBLY

Before mounting the saw on legs, astand or a bench, the

Table Insert and Blade Squareness and Blade Elevation

must be checked at this time,

INSTALLING ELEVATION AND TILT HANDWHEELS

1. Line up FLAT SPOTS on shaft and handwheel, push

handwhee] onto shaft, Install screw and Iockwasber to

lock handwheel on shaft.

LOCKWASHER

SCREW

TILT HANDWHEEL

CHECKING TABLEINSERT

I, With the insert in place, and sawblade all the way down,

use a small scale or straight edge to check near each of

the eight leveling tab positions, in order to determine if

the insert is flush with saw table surface at all eight tab

locations.

2. If the insert is above the table surface, the leveling tabs

must be adjusted.

A. Loosen Screw.

B. Lift insert from front end, and pull toward front of

sew,

C. Remove the insert, place it upside down on your

workbench end GENTLY TAP each of the tabs

downward only a slight amount. Replace insert...

check it and readjust tabs, if necessary.

LOCKWASHER

SCREW

ELEVATION HANDWHEEL

LEVELING TAB

3. If the insert is BELOW the table surface, remove the

insert and bend the tabs (with pliers) enough to make

the insert ABOVE the table surface.

4. To replace insert.

Place insert into insert opening in table and push

toward rear of saw to engage spring clip and until

keyslot in insert wi!l drop over screw. Tighten screw.

DO NOT TIGHTEN SCREW TO THE POINT WHERE IT

DEFLECTS THE INSERT.

CHECKING BLADE SQUARENESS TO TABLE

IMPORTANT: BLADE must be SQUARE (90 °) to

TABLE, in order to proceed with assembly.

1. Turn ELEVATION handwheel clockwise until blade is

up ashigh as it will go.

2. Check for BLADE SQUARENESS .. . if blade is not

square to table, adjust it at this time.

NOTE: The Combination Square must be "TRUE"-

See start of "Unpacking and Checking Contents section

on page 6for checking method.

Refer to "BLADE TILT, OR SQUARENESS OF

BLADE TO TABLE" adjustments on page 24.

CHECKING BLADE ELEVATION

Maximum depth of cut MUST NOT EXCEED TWO AND

ONE HALE (2-1/2 INCHES. This adjustment iS set at the

factory and should be checked to make sure that it has not

changed due to rough handling during shipment.

With the blade up as high asit will go, measure the distance

from the top of the table to top of the highest saw tooth. If

it is more than two and one half (2=1/2) inches, adjust it at

this time. Refer to "BLADE ELEVATION" adjustments on

page 26.

ATTACHING TABLE EXTENSIONS

If you received two Table Extensions with your saw

(furnished with Model No. 113.295750) attach them at this

time.

1. Position saw upside down on floor.

NOTE; To protect the finished surfaces of the saw and

extensions, lay a piece of heavy paper on the floor.

2, From among the loose parts find the following

hardware:

6 Hex Head ,_crew_6/16. -- 18 × 1 in. long

6 Lockwashers, 5/16 in. External Type

(approx: die; of hole 5/16 in,)

6 Flat Washers (dia. of hole 11/32 in.)

6 Hex Nuts, 5/16 - 18 (approx. die. of hole 5/16 in.)

3. Install screws, wasbars_ and nuts for extensions as

shown.., tighten screws SLIGHTLY.

BE SURE END OF EXTENSIONS ARE EVEN WITH

FRONT EDGE OF SAW.

4. Leave saw in upside down position until you attach the

rip fence guide bars and legs.

ifiii

FLAT WASHER

LOCKWASHER

MAKE SURE SQUARE

IS NOT TOUCHING

TiP OF TOOTH

SCREW

INSTALLING RIP FENCE GUIDE BARS

1. From among the loose _rts find the following

hardware:

2 Flex. Head Screws. 5/16 - 18 x1-I/2 in. long

2Flex. Head Screws, 5/16 - 18 x 1 in, long

4 Hex, Nuts, 5/16- 18 (approx. dia. of hole 5/16 in.)

4 External Lockwasbers, 5/16 in. (approx. dia. of hole

5/16 in,)

4 Flat Washers(Dia. of hole 21/64 in,)

2 Spacers, 3/4 in. dia, x 1/2 in. Ionf!

2 Self-threading nuts

2. Position guide bars on floor and instal hardware as

shown.., do not screw nuts on all the way,

EXT. LOCKWASHER HEX. HEAD SCREW

5/16 IN. I IN. LONG

FLAT WAS½ER /

HEX NU

5/16

FRONT GUIDE BAR

3. Place front guide bar against saw table and drop it in

place ... engaging the screws in the slot s. Make sure the

spacers are between the rail and the table.

4. End of front guide bar must be 5:13/16 in. from side of

saw table. Thi_ is important so that rip fence pointer

can be aligned.

6. With the blade of your combination square set to 1/4

in., use it as a gauge and attach the rail so that the edge

of the rail is 1/4 in. ABOVE the edge of the table.

5-13/16 IN.

6, Remove the three screws from rear of table extension,

7, Insert ends of FENCE GUIDE BAR ROD through

round holes at outer end of bars.

NOTE: The ends of the ROD are not threaded ... the

SELF THREADING NUTS will cut threads on the rod

as they are'screwed on.

8. Attach the rear bar in a similar manner, but make sure

that the end of the bar is 8-5/8 in. from the side of the

saw table.

FENCE GUIDE BAR ROD

SCREWS THROUGH

HOLES MARKED "X"

ASSEMBLING STEEL LEGS

NOTE: Steel Legs are furnished with Model 113.295750,

From among the loose parts, find the following Hardware:

24 Truss Head Screws, 1/4 - 20 x 5/8 in. long (top of

screw is rounded)

24 Lockwashers, 1/4 in. External Type (approx. dia. of

hole 1/4 in.)

24 Hex Nuts, 1/4 -20 (approx, dia. of hole 1/4 in.}

8 Hex Nuts, 1/2 -- 13 (approx. dia. of hole 1/2 in.)

4Leveling feet,

Assemble the legs asshown...

1. Insert the Truss Head Screws through the holes in the

legs, then through the holes in the stiffeners, MAKE

SURE THE SCREWS GO THROUGH THE HOLES IN

THE SIDE STIFFENERS MARKED "X".

2. Install Iockwashers and screw on the nuts but do not

tighten until completely assembled.

3. Install leveling feet.

END

STIFFENER _

SIDE STIFFENER

_:_.,._..----- LEVELING FOOT

MOUNTING SAW

I, Remove the four Truss Head screws, flatwashers,

Iockwashers and nuts from bottom of saw.

2. Position legs as shown and line up holes in stiffeners

with holes in saw base.

NOTE: At front of saw you will see four ,_etsof holes.

Insert bolts through holes closest to front of saw.

these holes are 9-1/4'" apart.

Replace the screws, washers, Iockwashers and nuts...

tighten the nuts.

3. Place saw mupright position.

i ,,,,,

If you mount the saw on any other bench, make sure that

there is an opening in the top of the bench the same size as

the opening in the bottom of the saw so that the sawdust

can drop through. Recommended working height is 33 to

37 in. from the top of the saw table tothe floor.

NOTE: All dimensions in inches,

,i,i

)/2

FRONT OF SAW

4 HOLES

;;'/16 OIA.

ALIGNING TABLE EXTENSIONS

1. "TAD" extensions upwards or downwards, using ablock

of wood and a hammer until they are even with top of

saw table. Be sureend of extensions are even with front

edge of saw,

2. Tighten screws.

BLOCK OF WOQD

3. Lay astraight piece of wood or aframing square on

table to act as a straightedge. If outer edge of extension

is higher or lower than table surface:

A, Slightly loosen nuts holding bracket to extension

using 7/16 in. wrench.

B. Move end of extension up or down until outer edge

is even with table surface ...check with GUIDE

BAR,.. tighten nuts.

C. Recheck INNER edge of extension to make sure it

has not moved ... readjust, if necessary.

4. Replace three screws in rear of table extension on right

side.

5. Hold rod with one hand and with a 7/16 in. wrench or

pliers start screwing on ONE of the nuts only A TURN

OR TWO... screw on other nut the same way.

Using TWO 7/16 in. wrenches or pliers tighten both of

the nuts.

IMPORTANT: Apply a coat of paste wax to the top surface

and front edge of the front guide bar. This will allow the

fence to slide more easily.

ALIGNING RIP FENCE

6. Position rip fence over miter gauge groove, holding up

the rear end while engaging front end with bar . ..

lower fence onto table,

The rip fence must be PARALLEL with the sawblade

and Miter Gauge grooves... Move fence until it is along

side of groove. Do NOT LOCK IT. It should be I_arallel

to groove. If it is not;

A. Loosen the two "Hex. Head Screws."

B. Hold fenCe head tightly against bar ... move end of

fence so that it is parallel with groove.

C. Tighten handle.

D. Alternately tighten the screws,

Place fence on saw but DO NOT LOCK IT.

Move the REAR END of the fence slightly to the right

or left . . . when you release it, the fence should

"spring" back to its original position.

If it does not, the spring pressure must be

INCREASED.

1. Loosen the screws,

2. Move Spring slightly toward front of fence.

If the fence does not slide easily along the bars, the

pressure of the spring can be REDUCe,

1. Loosen the screws.

2. Move spring slightly toward r_ar of (t_ncc . . .

tighten screws.

ADJUSTING RIP SCALE POINTER

1, Turn ELEVATION handwheel clockwise until blade is

up ashigh asit will go,

IMPORTANT: BLADE must be SQUARE (90 ° ) to

TABLE, in order to ALIGN rip fence,

2. Position fence on right side of sawblade so that it

touches the sides of the teeth.., tighten lock knob.

3. Loosen screw holding the pointer . . . adjust pointer so

that it points to "0"... tighten screw .....

NOTE: If you cannot adjust pointer so that it points to

"0", loosen the screws holding the front guide bar and

move the guide bar. LOCK KNOB

INSTALLING BLADE GUARD

1. From among the loose parts, find the hardware as

shown.

2. MAKE SURE THE BLADE IS ALL THE WAY UP

AND SQUARE WITH THE TABLE.

3. Position SPREADER SUPPORT on rod until it is even

with the end of the rod.

BLADE SQUARI

WITH TABLE

4. Assemble the 7/8 in. long setscrews, nuts, Iockwashers

and washers to the SPREADER SUPPORT BRACKET

and slip the nuts into the slot in the spreader support.

5. Finger tighten ONLY THE HEX NUTS.

6. Lay a piece of flat straight wood and a square on saw

table and rotate the SPREADER SUPPORT until the

bracket is aligned with square.

7. MAKE SURE END OF SUPPORT, BRACKET AND

ROD ARE EVEN .,, using an 1/8 in. setscrew wrench,

TIGHTEN THE SET SCREWS ONLY.

IMPORTANT: The SPREADER must always be

PARALLEL to the sawblade and in the MIDDLE of the cut

(KERF) made by the sawblade.

NOTE: The spreader isthinner than the width of the KERF

by approximately six thicknesses of paper.

SPACE EQUAL TC APPROX

3THICKNESSE! OF PAPER

KERF WOOD

BLADE

SPACE EQUAL TO APPRO_

3 THICKNESSES OF PAPER

LOOKING DOWN ON SAW

8_ Make two folds in a small piece (6 x6 in.) of ordinary

NEWSPAPER making three thicknesses. The folded

paper will be used as a "'specing gauge".

9, Install the SPREADER CL.tW1P. Place spreader between

spreader clamp and bracket, Move forward until all

three are in line. TIGHTEN WlNGSCREWS.

10. Lift up both ANTIKICKBACK PAWLS... insert one

of the setscrew wrenches or a pencil in the notches to

hold the pawls out of the way.

11. Lay apiece of straight flat wood against the sawblade.

Insert folded paper between spreader and strip of wood.

12. MAKE SURE THE HEX NUTS UNDERNEATH ARE

LOOSE.

13. Hold the spreader tightly against the wood and make

sure the wood is against the saw blade. TIGHTEN THE

HEX NUTS.

This will align the spreader in the middle of the cut

(KERF) made by sawblade.

THREE

THICKNESSES

OF PAPER

SPREADER

CLAMP

PIECE OF

ANTIKICK BACK

PAWLS STRAIGHT WOOD

HOLD WOOD 1

TIGHTLY AGAINST

BLADE

SPREADER

TIGHTLY AGAINST WOOD

SPREADER

_RACKET

. GETTING TO KNOW YOUR SAW

MITER GAUGE 7BLADE GUARD ANTtKICKBACK

LOCK KNOB PAWLS

MITER GAUGE 9 SAW BLADE SPREADER 5

6MITER GAUGE HEAD R_P FENCE

\HOLES FOR

FACING

4 Tilt HANDWHEEL

3ELEVATION RIP FENCE

LOCK KNOB

2 RESET BUTTOt

0 N-OFF SWITCH

I ON-OFFSW,TCR II;

CAUTION: Before turning switch on, make sure the blade

guard is correctly installed and operating properly.

The On-Off Switch has a locking feature. THIS SHOULD

PREVENT UNAUTHORIZED AND POSSIBLY

HAZARDOUS USE BY CHILDREN AND OTHERS.

A. Insert key into switch.

B. TO turn saw ON .,, stand to either side of the

blade never in line with it , ,. insert finger under

switch lever and pull END of lever out.

After turning switch ON, always allow the blade to

come up to full speed before cutting.

Do not cycle the motor switch on and off rapidly,

as this may cause the sawblade to loosen, In the

event this should ever occur, allow the sawblade to

come to a complete stop and retighten the arbor

nut normally, not excessively. Never leave the saw

while the power is "ON".

C. TO turn saw OFF .,. PUSH lever in, Never leave

the saw until the cutting tool has come to a

complete stop.

D. TO lock switch in OFF position,., hold switch IN

with one hand .., REMOVE key with other hand.

WARNING: FOR YOUR OWN SAFETY, LOWER

BLADE OR OTHER CUTTING TOOL BELOW

TABLE SURFACE. (IF BLADE IS TILTED.

RETURN IT TO VERTICAL (90 ° ) POSITION).

ALWAYS LOCK THE SWITCH "OFF". WHEN

SAW I:S NOT IN USE ,.. REMOVE KEY AND

KEEP IT IN A SAFE PLACE ... ALSO ... IN

THE EVENT OF A POWER FAILURE (ALL OF

YOUR LIGHTS GO OUT) TURN SWITCH OFF

... LOCK IT AND REMOVE THE KEY. THIS

WILL PREVENT THE SAW FROM STARTING UP

AGAIN WHEN THE POWER COMES BACK ON.

KEY

ON-OFF SWITCH

--4z:_j j

KEY

YELLOW PLASTIC)

2 RESET BUTTON .. See "Motor Specifications and

Electrica Requirements" section. "Motor Safety

Protection."

NOTE: When bevel crosscutting, attach facing so that it

extends to the right of the miter gauge and use the miter

gauge in the groove to the right of the blade.

3 ELEVATION HANDWHEEL... elevates or lowers the

blade. Turn clockwise to elevate.., counterclockwise

to lower.

NOTE: WHEN THE BLADE IS TILTED TO 45 ° , IT

CANNOT BE LOWERED ALL THE WAY BELOW

THE TABLE. IT WILL PROJECT APPROX. 1/2 IN

4TILT HANDWHEEL ... tilts the blade for bevel

cutting. Turn clockwise to tilt toward left ...

counterclockwise to tilt toward right.

When the blade is tilted to the LEFT as far as it will go,

it should be at 45° to the table and the bevel pointer

should point 45°.

NOTE: There are LIMIT STOPS inside the saw which

prevent the blade from tilting beyond 45° to the LEFT

and g0° to the RIGHT. (See "Adjustments" section

"Blade Tilt. or Squareness of Blade to Table").

5RIP FENCE ... is locked in place by tightening the

lock knob. To move the fence, oose_ the lock knob

and graspthe fence with one hand at the front. 8

Holes are provided in the rip fence for attaching a wood

facing when using the dado head, or molding head.

\\\\

BLADEGUARD must always he in place and working

properly for all thru-sawing cuts. That is, all cuts

whereby the blade cuts completely through the

workpiece.

To remove the guard for special operations, loosen the

wmgscrews and move spreader awm/ from saw and lift

upwards. DO NOT DISTURB THE SETTING OF THE

REX NUTS.

When replacing the guard, make sure the spreader is

moved toward front of saw so that wingscrews are at

end of slots. TIGHTEN THE WlNGSCREW_S

SECURELY.

TABLE INSERT is removable for removing or installing

blades or other cutting tools..

Select apiece of smooth straight wood appro×, 3/4 in,

thick and the same size as the rip fence.

Attach it to the fence with three Round Head # f0

Wood Screws 2 in, long. To remove the facing, loosen

the screws, slide the facing forward and pull the screws

throu_ the round holes.

ANTIKICK BACK

PAWLS

WOOD FACING

#1oWOOD SCREWS

6MITER GAUGE .. head is locked in position for

crosscutting or mitering by tighting the lock knob,

ALWAYS LOCK IT SECURELY WHEN IN USE.

Notches are provided in the miter gauge for attaching

an AUXILIARY FACING to make it easier to cut long

pieces, Be positive facing does not interfere with the

proper operation of the sawblade guard.

Select asuitable piece of smooth straight wood.., drill

two holes through it and attach it with screws.

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE REMOVING INSERT.

A, Lower the blade below the table surface.

B. Loosen screw.

C. Lift antikickback pawls.

D. Lift insert from front end, and pull toward front of

saw.

NEVER OPERATE THE SAW WITHOUT THE PROPER

INSERT IN PLACE. USE THE SAW BLADE INSERT

WHEN SAWING .,. USE THE COMBINATION DADO

MOLDING INSERT WHEN DADOING OR MOLDING.

REMOVING AND INSTALLING SAWBLADE

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE REMOVING OR INSTALLING

SAWBLADE.

A. Remove insert,

B. Place ARBOR wrench on flat surfaces of saw

ARBOR . . . ARBOR NUT wrench on nut . . .

position wrenches as shown .. . hold your hands

well aboveblade,

C. With ARBOR wrench against table, PULL ARBOR

NUT wrench FOREWARD to LOOSEN nut.

D. To TIGHTEN nut ,. . HOLD ARBOR wrench

against rear of table . o . PUSH ARBOR NUT

wrench toward rear.

NOTE: When installing the blade ...make sure the

teeth are pointing toward the fiont of the saw.., and

that the blade and collars are clean, and free from any

burrs.

The HOLLOW side of the collars must be against the

blade.

Always tighten the arbor nut securely.

E. To replace insert,

Place insert into insert opening in table and push

toward rear of saw until keyslot in insert will drop

over screw. Tighten screw.

Do not tighten screw to the point where it will

deflect the insert.

_\ \ PULL TO LOOSEN

_O TIGHTEN

ARBOR

FLAT SURFACES COLLAR

TEETH FOI

FRONT OF SAW

HEX NUT

BASIC SAW OPERATION

USING THE MITER GAUGE

CROSSCUTTING, MITER CUTTING, BEVEL CUTTING,

COMPOUND MITER CUTTING and when RABBETING

acrossthe end of narrow workpiece, THE MITER GAUGE

IS USED.

WARNING: FOR YOUR OWN SAFETY, ALWAYS

OBSERVE THE FOLLOWING SAFETY PRECAUTIONS

IN ADDITION TO THE SAFETY INSTRUCTIONS ON

PAGES 2,3, and 4.

1, Never make these cuts freehand (without using the

miter gauge or other auxiliary devices) because the

blade could bind in the cut and cause aKICKBACK or

cause your fingers or hand to slip into the blade,

2. Always lock the miter gauge securely when in use.

3, Remove rip fence from table.

4, Make sure blade guard is installed for all "THRU-

SAWING" operations (when sawblade cuts entirely

thru the thickness of the workpiece.) Replace guard

IMMEDIATELY after completion of dadoing, molding

or rabbeting cuts.

5. Have blade extend approximately 1/8 in. above top of

workpiece. Additional blade exposure would increase

the hazard potential.

6. Do not stand directly in front of the blade in case of a

THROWBACK (Small cot-off piece caught by the back

of the blade and thrown toward the operator). Stand to

either side of the blade.

7. Keep your hands clear of the blade and out Of the path

of the blade.

8. If blade stalls or stops while cutting, TURN SWITCH

OFF before attempting to free the blade.

9. Do not reach over or behind the blade to pull the

workpiece through the cut.., to support long or heavy

workpieees.., to remove cot-off pieces of material or

FOR ANY OTHER REASON.

10. Do not pick up small piecesof cut-off material from the

table. REMOVE them by pushing them CFF the table

with a long stick. Otherwise they could be thrown back

at you by the rear of the blade,

11. Do not remove small piecesof cut-off material that may

become TRAPPED inside the blade guard while the sew

is RUNNING. THIS COULD ENDANGER YOUR

HANDS or cause aKICKBACK.

Turn the saw OFF. After the blade has stopped turning,

lift the guard and remove the p_ece.

WORK HELPERS

Before cutting any wood on your saw, study all of the

"Basic Saw Operations".

Notice that n order to make some of the cuts, it s

necessary to use certain devices "Work Helpers" like the

Push Stick the Push Block and the Au×iliarv Fence which

you can make yourself.

After you have made a few practice cuts, make these

"helpers" before starting any projects. Make the "'Pusll

Stick" first.

PUSH STICK

NOTCH

PUSH STICK AND PUSH BLOCK

Make the Push Stick using a piece of 1x 2, or rip one from

a wide board, say 11-1/2 in, wide, and set the rip fence

9-7/8 in. from the sawblade.

Make the Push Block using a piece of 3/8 in. and 3/4 in.

plywood.

The small piece of wood 3/8 in. x 3/8 in. × 2-1/2 in. should

be GLUED to the plywood... DO NOT USE NAILS. This

is to prevent dulling the sawblade in the event you

mistakingly cut into the push block.

Position the handle in the center of the plywood and fasten

tosether with glue and woodscrews.

AUXI LIARY FENCE

Make one using a piece of 3/8 in. and 3/4 in. plywood.

Fasten _ogether with glue and woodscrews_

NOTE: Since the Push Block is used with the Auxiliary

Fence, the 4-3/4 in. dimensions must be held identical on

both the pieces.

THESE EDGES MUST

_E PARALLEL WOOD

NOT'E: All dimensions _n inches

PUSH BLOCK

3/8 PLYWOOD

THIS FACE AND THIS EDGI

EDGE MUST BE PARALLEL

3/8 pLYWOOD

NOTE: All d_menslons _n inches

AUXILIARY FENCE

3/4 pLYWOOD

CROSSCUTTI NG

CROSSCUTTING is known as cutting wood across the

grain, at 90 O, or square with both the edge and the flat side

of the wood. This is done with miter gauge set at "0".

The graduations on the mite'r gauge provide accuracy for

average woodworklng. In Some cases where extreme

accuracy is required, when making angle cuts; for example,

make a trial cut and' then recheck it with an accurate

square, or protractor.

If necessary, the miter gauge head can be swiveled slightly

to compensate for any inacurracy.

NOTE: The space between the miter gauge bar and the

groove in the table is held to a minimum during

manufacturing.

For maximum accuracy when using the miter gauge, always

"favor" one side of the groove in the table. In other words,

don't move the miter gauge from side to side while cutting,

but keep one side of the bar riding against one side of the

groove.

NOTE: Glue a piece of sandpaper to the face of the miter

gauge head. This will help prevent the workpiece from

"creeping" while it is being cut.

The Hold-Down Clamp (Optional Accessory) should be

used on the miter gauge for greater accuracy.

The miter gauge may be used in either of the grooves in the

table. Make sure it is locked.

When using the miter gauge in the LEFT hand groove, hold

the workpieee firmly against the miter gauge head with

your left hand, and grip the lock knob with your right.

PLYWOOD

CLAMP_.D

tO SAWHORSE

When using the RIGHT hand groove, hold the workpiece

with your right hand and the lock knob with your left

hand.

When crosscutting a long board, make sure that it is

supported.

You can make a simple support by clamping a piece of

plywood to a sawhorse.

When cutting long workpieces, invert the AUXILIARY

FENCE!WORK SUPPORT, and position it on top of the

guide bars to support the workpiece as near to the end as

possible. If this does not adequately support the workpiece,

you can make a simple support by clamping a piece of

plywood to a sawhorse.

Use the Hold-Down Clamp (Optional Accessory) on the

miter gauge for greater accuracy.

AUXILIARY

WORK SUPPORT

REPETITIVE CUTTING

REPETITIVE CUTTING is known as cutting a quantity of

pieces the same length without having to mark each piece.

1. Use the Stop Rods (optional accessory) only for cutting

duplicate pieces6 in, long and longer.

2, DO NOT FEED workpiece with RIGHT hand, merely

guide it, making sure that it does not bind or pinch the

sawblade.

When making repetitive cuts from a long workpiece, make

sure it is adequately supported.

Use the Hold-Down Clamp (Optional Accessory) on the

miter gauge for greater accuracy.

\STOP RODS

1. NEVER USE THE RIP FENCE AS A LENGTH STOP

BECAUSE THE CUTOFF PIECE COULD BIND

BETWEEN THE FENCE AND THE BLADE CAUSING

A KICKBACK.

2. When making repetitive cuts shorter than 6 in., clamp a

block of wood 2 in. long to the table to act as alength

stop, Do not clamp directly to the bottom edge of the

table because the "swivel" of the clamps will not grip

properly. Place asmall block of wood between the

bottom edge of the table and the "C" clamps.

CAUTION: When clamping the block, make sure that

the end of the block is well in front of the sawblede, Be

sure it is clamped securely,

3. Slide the workpiece along the miter gauge until it

touches the block.., hold it securely or clamp it with

the Hold-Down Clamp (Optional Accessory).

4. Make the cut.., pull the workpiece beck.., push the

cut off piece off the table with a tong push stick... OO

NOT ATTEMPT TO PICK IT UP AS THIS COULD

ENDANGER YOUR HANDS.

BLOCK

CUT OFF

PIECE

MITER CUTTING

MITER CUTTING is known :as cutting wood at an angle

ott_er than 90° with the edge of the wood. Follow the same

procedure as you would for crosscutting,

Adjust the miter gauge to the desired angle, an_ lock it.

The miter gauge may he used in either of the grooves in the

table.

When using the miter gauge in the LEFT hand groove, hold

the workpiece firmly against the miter gauge head with

your left hand, and grip the ock knob with your right.

When using the RIGHT hand groove, hold the workpiece

with your right hand and the lock knob with your left

hand.

Use the Hold-Down Clamp (Optional Accessory) on the

miter gauge for greater accuracy,

BEVEL CROSSCUTI NG

BEVEL CROSSCUTTING is the same as crosscutting

except that the wood is also cut at an angle.., other than

90° with the flat side of the wood.

Adjust the blade to the desired angle.

Use the Miter Gauge in the groove to the RIGHT of the

blade. It cannot be used in the groove to the left because

the blade guard will interfere. Hold the workpiece with

your right hand and the lOCKknob with your left hand.

Use the Hold-Down Clamp (Optional Accessory) on the

miter gauge for greater accuracy,

COMPOUND MITER CUTTING

COMPOUND MITER CUTTING is a combination of miter

cutting and bevel crosscutting. The cut is made at an angle

other than 90 ° to both the edge and the flat side of the

wood.

Adjust the miter gauge and the blade to the desired angle.

.Make sure miter gauge is locked,

USING THE RIP FENCE

RIPPING, BEVEL RIPPING, RESAWING AND

RABBETING are performed using the RIP FENCE together

with the AUXILIARY FENCE. PUSH STICK OR PUSH

BLOCK

WARNING: FOR YOUR OWN SAFETY, ALWAYS

OBSERVE THE FOLLOWING SAFETY PRECAUTIONS

IN ADDITION TO THE SAFETY INSTRUCTIONS ON

PAGES 2, 3, and 4,

1. Never make these cuts FREEHAND (without usingthe

rip fence or auxiliary devices when required) because

the blade could bind i_ the CUt and cause a

KICKBACK.

2. Always lock the tip fence securely when in use.

3. Remove miter gauge from table.

4. Make sure blade guard is installed for all thru-sawing

type cuts. Replace the guard IMMEDIATELY following

completion of resawing, rabbeting, dadoing, or molding

operations.

Frequently check the action of the ANTIKICKBACK

PAWLS by 0assing the workpiece alongside of the

spreader while saw is'OFF.

Pull the workpiece TOWARD you. If the PAWLS do

not DIG into the workpiece and HOLD it... the pawls

must be SHARPENED. See "Maintenance" sectior

Have blade extend approximately 1/8 in. above top of

workpiece. Additional blade exposure would increase

the hazard potential.

Do not stand directly in front of the blade in case of a

KICKBACK. Stand to either side of the blade.

Keep your hands clear of the blade and out of the path

of the blade.

If the blade stalls or stops while cutting, TURN

SWITCH OFF before attemptingto free the blade,

Do not reach over or behind the blade to pull the

workpiece through the cut.., to support long or heavy

workpieces . . .to remove small cut-off p=eces of

material or FOR ANY OTHER REASON.

10. Do not pick up small pieces of cut'off material from the

table. REMOVE them by pushing them OFF the table

with along stick. Otherwise they could be thrown back

at you by the rear of the blade.

1f. Do not remove small pieces of cut-off material that may

become TRAPPED insidethe blade guard while the saw

is RUNNING. THIS COULD ENDANGER YOUR

HANDS or cause a KICKBACK.

Turn the saw OFF. After the blade has stopped turning,

lift the guard and remove the piece.

RIPPING

RIPPING is know as cutting apiece of wood wffh the grain,

or lengthwise. This is done using the rip fence.

Position the fence to the desired WIDTH OF RIP and lock

in place.

Before starting to rip, be sure

A. Rip Fence is parallel to sawblade.

13. Sprcader is properly aligned with sawblade.

C. Antikickback pawls are functioning properly.

When ripping LONG BOARDS or LARGE PANELS, always

use awork support.

A simple one can be made by clamping apiece of plywood

to asawhorse.

BEVEL RIPPING

When bevel ripping material 6 in. or narrower, use fence on

the right side of the blade ONLY, This will provide more

space between the fence and the sawblade for use of a push

stick. If the fence is mounted to the left, the sawblade

guard may interfere with proper use of a push stick.

ALWAYS SUPPORT LONG WORKPIECES

When "WIDTH OF RIP" is 6in. and WIDER use your

RIGHT hand to feed the workpiece until it is clear of the

table.

Use LEFT hand ONLY to guide the workpiece.., do not

FEED the workpiece with the left hand,

When "WIDTH OF RIP" is 2in. to 6in. wide USE THE

PUSH STICK to feed the work

When WIDTH OF RIP is NARROWER than 2 in., the push

stick CANNOT be used because the guard will interfere, ..

USE the AUXILIARY FENCE/WORK SUPPORT and

PUSH BLOCK.

Attach Auxiliary Fence/Work Support to rip fence with

two "C _' clamps.

AUXILIARY PENCF/

/WORK SUPPORT

Feed the wOrkpiece by hand along the AUXLIARY

FENCE/WORK SUPPORT Until the end is approx. 1 in.

past the front edge Of the table. Continue to feed using the

PUSH BLOCK.

Hold the workpiece in position and install the PUSH

BLOCK by Sliding it on top of the AUXILIARY

FENCE!WORK SUPPORT (this may raise guard).

BAFFLE

Narrow strips thicker than the Auxiliary Fence/Work Support

may enter the guard and strike the baffle. CAREFULLY raise

guard only enough to clear the workpiece. Use PUSH BLOCK

to complete cut,

RESAWING

RESAWING is known as ripping a piece of wood through

its thickness. Do not attempt to resaw BOWED or

WARPED material NOTE: to RESAW a piece of wood

wider than 2-1/2 in.... it will be necessary to remove the

blade guard ... and use the AUXILIARY FENCE/WORK

SUPPORT (See Page 18)

Clamp it to the table so that the workpiece will SLIDE

EASILY (but not TILT or MOVE SIDEWAYS) without

BI NDI NG between the two fences.

Do not clamp directly to the bottom edge of the table

because the "swivel" of the clamps wilt not grip properly.

Place a small block of wood between the bottom edge of

the table and the "C'" clamps,

WARNING: FOR YOUR OWN SAFETY...

1 DO NOT "BACK UP" (REVERSE FEEDING) WHILE

RESAWING BECAUSE THIS COULD CAUSE A

KICKBACK.

SMALL BLOCK

OF WOOD

2. INSTALL BLADE GUARD IMMEDIATELY UPON

COMPLETION OF THE RESAWING OPERATION.

CUTTING PANELS

When cutting panels (whenever fence is positioned outside

of table surface), ALWAYS use the AUXILIARY

F ENCE/WOR K SUPPORT.

1, Unlock fence and raise rear end.

2. Position AUXILIARY FENCE_VORK SUPPORT as

shown and attach it with two "'C" clamps.

_,UXlLIMY FENCE/"

WORK SUPPORT

RABBETING

Rabbeting is known as cutting out a section of the corner

of a piece of material.

To make a RABBET requires two cuts which do not go all

the way through the material. Therefore the blade guard

must be removed.

1. Remove blade guard.

2. Adjust rip fence and blade to required dimensions.

3. Make first cut through edge. Follow resawing

procedure.

4. Remove auxiliary fence and make second cut.

5. INSTALL BLADE GUARD IMMEDIATELY UPON

COMPLETION OF RABBETING OPERATION.

Rabbet cuts can also be made using the dado head or

molding head.

DADOING

Instructions for operating the Dado Head are contained in

booklet furnished with the Dado Head.

The recommended Dado Head is listed, under

recommended Accessories.

The arbor on the saw, is only long enough so that the

widest cut that can be made is 13/16" wide.

When installing the dado head on the arbor, ALWAYS;

install the inside "loose collar" first.

It is not necessary to install the outside loose collar before

screwing on the arbor nut. Make sure the arbor nut is tight.

ALWAYS USE DADO INSERT listed under recommended

Accessories,

When using the dadoing head it will be necessary to remove

the Blade Guard and Spreader. USE CAUTION.

ALWAYS REPLACE THE BLADE GUARD AND

SPREADER WHEN YOU ARE FINISHED DADOING.

MOLDING CUTTING

Instructions for operating the Molding Head are contained

in a booklet furnished with the Molding Head.

The recommended molding head is listed under

recommended Accessories.

Always use Molding Insert listed under recommended

Accessories.

LOOSE

DADO INSERT

HEAD

ARBOR NUT

When using the molding head it will be necessary to remove

the Blade Guard and Spreader. USE CAUTION.

ALWAYS REPLACE THE BLADE GUARD AND

SPREADER WHEN YOU ARE FINISHED MOLDING:

ADJUSTMENTS

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE MAKING ANY ADJUSTMENTS.

MITER GAUGE

NOTE: The graduations on the miter gauge provide

accuracy for average woodworking. In some cases where

extreme accuracy is required, when making angle cuts, for

example, make a trial cut and then recheck it with an

accurate square or protractor.

If necessary, the miter gauge head can be swiveled slightly

1:ocompensate for any inaccuracy.

The HEAD should be SQUARE (90 ° ) with the bar when

the pointer points to "0",

To check for squareness, place an accurate square on the

miter gauge. If the head is NOT SQUARE with the bar:

1. Loosen the lock knob.

KNOB

BAR

2. Position the head square with the bar ... tighten the

lock knob.

3. Loosen the screw and adjust the pointer, so it points to

zero.

The swiveling movement of the head can be adjusted by

tightening or loosening the set screw located in side of the

head using the t/8 in. setscrewwrench.

HEELING ADJUSTMENT or PARALLELISM

OF SAWBLADE TO MITER GAUGE GROOVE

While cutting, the material must move in a straight line

PARALLEL to the SAWBLADE . therefore both the

miter gauge GROOVE and the RIP FENCE must be

PARALLEL to the SAWBLADE.

If the sawblade IS NOT para)lel to the miter gauge groove,

the blade will bind at one end of the cut, (This is known as

"'HEELING").

To check for p_rallelism:

WARNING - FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET.

1. Raise blade all the way up... raise blade guard.

2. Mark an "X" on one of the teeth which is SET (bent)

to the LEFT.

3. Place the head of a combination square in the

GROOVE . .adjust blade of square so that it just

touches the tip of the MARKED tooth.

4. Move square to REAR, rotate blade to see if MARKED

tooth again touches blade of square.

5. )f tooth touches square the same amount at FRONT

and REAR . . . sawblade s PARALLEL to MITER

GAUGEGROOVE.

if tooth does not touch front and rear.., the mechanism

underneath must be adjusted to make the blade

PARALLEL to GROOVE.

1, Loosen the 4screws (about 1/4 to 1/2 turn) using 3/16

in. setscrew wrench furnished with saw. Also loosen the

2pan head 10-32 screws (about 1/4 to 1/2 turn)

located at rear of the table top asshown. This will allow

the mechanism below the table to be shifted sideways.

2. Fold apiece of cardboard or heavy paper over the blade

to protect your hands.

3. Graso the blade and move it to the right or left a small

amount and tighten one of the screws.

4. Check with square to determine if MARKED TOOTH

touches square the same amount at front and rear.

It it does, tighten other three screws. If it does not,

loosen screw and move blade the required amount,

5. Alternately tighten the screws slowly.

NOTE: Use the setscrew wrench as shown . . ,do not

use a pair of pliers or any other tool to gain more

leverage on the setscrew wrench.

BLADE TI LT, OR SQUARENESS

OF BLADE TO TABLE

90° (SQUARE) and 45 ° (BEVEL) STOP COLLARS.

When the bevel _inter is pointing directly to the "0"" mark

on the bevel scale, the sawblade should make a SQUARE

cut 90° to the table,

To check for SQUARENESS:

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET.

1. Raise blade all the way4JP.., raise blade guard,

2, TILT blade a few degrees to the LEFT .. . now tilt

blade back to the RIGHT asfar as it wil go.

3. Place the square against blade. Make sure square is not

touching the TIP of one of the saw TEETH,

3/16 IN.

SETSCREW

WRENCH

If bladeISSQUARE to table;

A. Check pointer

If POINTER DOES NOT point to the "0" mark on the

bevel scale;

B. Remove Elevation Handwheel

C. Loosen screw and adjust pointer.., using medium

screwdriver.

D, Install Elevation Handwheel

BEVEL SCALE ADJUSTING SCREW

If blade is NOT SQUARE to table.,, the 90°LIMIT STOP

must be ADJUSTED.

CAUTION: Cover blade with piece of cardboard to protect

your hand.

1. Using a small size screwdriver, reach UNDERNEATH

saw and loosen BOTH setscrewsin 90° STOP COLLAR.

NOTE: If you can't reach the setscrews, turn the TILT

HANDWHEEL slightly.

2. ROTATE the STOP COLLAR moving it away from

pivot nut.

3. TILT blade RIGHT or LEFT ... checking with your

square until blade is square to table.

4. ROTATE STOP COLLAR moving it toward PIVOT

NUT until it TOUCHES the PIVOT NUT... TIGHTEN

the setscrews,

5. Check POINTER, If it DOES NOT point to the "0'"

mark on the bevel scale.

A. Remove Elevation Handwheel

B, Loosen screw and adjust pointer . . . using medium

screwdriver.

C. Install Elevation Handwbeel

POINTERADJUSTING SCREW

ELEVATION

HANDWHEEL

POINTER BEVEL SCALE

ADJUSTING SCREW

PiVOt NUT

90= STOP COLLAR

TILT blade to LEFT as far as it will go. It will stop when

the PIVOT NUT is against the 45 ° STOP COLLAR.

A. Place an ACCURATE square against blade. Make

sure square is not touching the TiP of one of the

saw TEETH;

If blade is 45° to table;

A. Check pointer.

If POINTER DOES NOT point to the 45 ° mark on the

scale;

A. Loosen two screws on scale and adjust scale until

POINTER points to 45 ° mark.

If blade is NOT 45 ° to table ... the 45 ° STOP COLLAR

end SCALE must be ADJUSTED

t. Remove Elevation Handwheel.

2, Using a small size screwdriver, reach thru curved

slot in front trim panel and loosen BOTH setscrews

in 45 ° STOP COLLAR.

NOTE: If you can't reach the setscrews, turn _he

TILT HAN DWH EEL slightly.

3. ROTATE the STOP COLLAR moving it IN or OUT

and TILT blade RIGHT or LEFT... checking with

your square until blade is 45 ° to table.

4_ TIGHTEN thesetscrgws_

NOTE: If you can't reach the setscrews, turn TILT

HANDWHEEL slightly.

5. Loosen two screws on scale and adjust scale until

POINTER points to 45 ° mark.

6. Install Elevation Handwheel. BACK OF SAW

STOP COLLAR

BLADE ELEVATION

When the elevation hendwheel is turned CLOCKWISE, until

it stoos, the blade must not be more than two and one half

12-1/2) inches above the table. If the blade extends more

than 2-1/2 inches, the motor could interfere with the

underside of the table causing misalignment.

With the blade extending two and one half (2-1/2) inches

above the table, the STOP COLLAR and SPACER must be

against the ELEVATION SCREW PIVOT NUT. If the blade

extends more than two and one half inches, loosen two

screws in STOP COLLAR, and readjust it,

SPACER

ELEVATIC _ SCREW

PIVOT NUT SCREW

TILT SCREW TILT SCREW

PIVOT NUT

TILT AND ELEVATION MECHANISM

The NANDWHEELS should turn freely without binding.

The turning action can be adjusted by tightening or

Ioosenlng the screws in the bearing retainer. Both

handwheels must be removed to reach the adjusting screws.

NOTE: When adjusting the screws on the TILT bearing

retainer, hold the nut inside using a3/8 in. wrench. The

screws for the ELEVATION bearing retainer can be reached

with a small screwdriver through the curved slot on the

front of the saw.

ADJUST THESE

TWO SCREWS

TILT

dANDWHEEL

ELEVATION

HANDWHEEL

ADJUST THESE

TWO SCREWS

MAINTENANCE

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE MAINTAINING OR LUBRICATING

YOUR SAW.

Do not allow sawdust to accumulate inside the saw.

Frequently blow out any dust that may accumulate inside

the saw cabinet and the motor.

Frecluently clean your cutting tools with Craftsman Gum

end Pitch Remover.

A coat of automobile-type wax applied to the table will

help to keep the surface clean and allow workpieces to slide

more freely.

If the Dowel cord s worn or cut. or damaged in any way,

have it replaced immediately,

Make sure tne teeth of the ANTIKICKBACK pawls are

always sharp, To sharpen:

2. Rotate pawl Loward rear of spreader so that teeth are

above top of spreader.

3. Hold spreader with left hand and place pawl over corner

of workbench.

4. Using a small rouna file (Smooth Cul sharpen the

teeth

1 Remove blade guard.

LUBRICATION

The saw motor bearings have been packed at the factory

with proper lubricant and require no additional lubrication.

The following parts should be oiled occasionally with SAE

No. 20 or No. 30 engine oil.

!. Tilt screw threads and pivot nut. (First Clean with

Craftsman Gum & Pitch Remover.)

2. Elevation screw threads and pivot nut. (First Clean with

Craftsman Gum & Pitch Remover.)

3. Cradle bearing points.

4. Bearing points in guard assembly, miter gauge and ri_

fence.

ELEVATION SCREW

_-) /

='LEVATIONSCREW

PIVOT NUT

TILT SGREW TILT SGREW

PIVOT NUT

RECOMMENDED ACCESSORIES

ITEM CAT.NO. ITEM

Steel Legs ............................... g-22235

Steel Stand .. :........................... 9-22214

Retractable Caster Set ..................... 9-22208

Solid Table Extension ...................... 9-29954

*7 in, Molding Head Set ............... 9-3217 9-3218

*7 in, Molding Head ........................ 9-3214

Molding/Dado Insert for 7 in

Dia. Molding or dado Head .................. 9-29933

Work Light ............................... 9-2480

CAT.NO.

Work Light ............................... 9-2481

7 in. Dia. Adjustable Dado Head ............... 9-326:3

7in. Dia. Dado Head ....................... 9-3257

Sanding Wheel ............................ 9-2274

Miter-Gauge Stop Rods ..................... 9-29924

Miter*Gauge Hold-Down Clamp .............. 9-29928

Taper Jig ................................. 9-3233

Universal Jig ............................. ,9-3231

"'Power Tool Know How Handbook" Table Saw .. 9-291',3

The above recommended accessories are current and were

available at the time this manual was printed.

*Smaller Dia. Molding Heads cannot be used because they

do not provide adequate depth of cut.

TROUBLE SHOOTING

WARNING: FOR YOUR OWN SAFETY. TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE TROUBLESHOOTING.

TROUBLE SHOOTING -- GENERAL

TROUBLE PROBABLE CAUSE REMEDY

Discard Blade and use a different blade.

See "Adjustments" section "Miter Gauge.'"

Sharpen or replace blade.

Excessive vibration.

Cannot make square

Cut when crosscutting.

Cut binds, burns or

stalls motor when

ripping.

1. Blade out of balance.

1. Miter gauge not adjusted

properly,

1. Dul! blade with improper

tooth set.

2, Blade is Heeling.

3. Warped board,

See "Adjustments" section, "Heeling Adjustment..."

Make sure concave or hollow side is facing

"down," feed slowly.

See "Assembly" section, "Aligning Rip Fence"

4. Rip fence not parallel

to blade.

5. Spreader out of

alignment

1, Stop collars not properly

adjusted,

1, Sawdust on threads of tilt

screw or elevating screw.

2. Bearing retainers

to tight.

Cut not true at 90°

or 45 ° positions.

Tilt and elevating

handwheels turn hard.

See "Maintenance" section

"'Tilt and Elevation Mechanism."

See "Assembly" section, "Installing

Blade Guard."

See "Adjustments" section, "Blade Tilt, or

"Squareness of Blade to Table."

See "Maintenance and Lubrication" section,

TROUBLE SHOOTING -- MOTOR

NOTE: Motors used on wood-working tools are particularly

susceptible to the accumulation of sawdust and wood chips

and should be blown out or *'vacuumed" frequently to

prevent interference with normal motor ventilation.

NOTE: The starting relay is a GRAVITY SENSITIVE

TYPE. NEVER TURN THE POWER ON WHILE THE SAW

IS UPSIDE DOWN AS THIS WILL DAMAGE THE

MOTOR.

TROUBLE PROBABLE CAUSE REMEDY

Excessive noise. 1. Motor. 1. Have motor checked by qualified service

technician, Repair se_ice is available at

your nearest Sears store.

1, Do not use other appliances or motors on

same circuit when using the saw,

Motor fails to develop

full power. (Power

output of motor decreases

rapidly with decrease in

voltage at motor terminals.

For example, a reduction

of 10% in voltage causes

a reduction of 19% in

maximum power output

of which the motor is

capable, while areduction

of 20% in voltage causes

a reduction of 36% in

maximum power output,)

1. Circuit overloaded with

lights, appliances and

other motors.

2. Undersize wires or circuit

too tong.

3, General overloading of

power company

facilities, fin some

sections of the

country, demand for

electrical power may

exceed the capacity

of existing generating

and distribution systems.)

4. Incorrect fuses or circuit

breakers in power line.

2. Increase wire sizes, or reduce length of wiring,

See "Motor Specification and Electrical

Requirements" section

3. Request avoltage check from the power company.

4. Install correct fuses or circuit breakers.

TROUBLE SHOOTING -- MOTOR (Continued)

TROUBLE

Motor starts slowly

or fails to come up

to full speed.

Motor overheats-

Starting relay in

motor will not

operate.

Motor stalls

(resulting in blown

fusesor tripped

circuit breakers).

Frequent opening of

fusesor circuit

breakers.

PROBABLE CAUSE

1. Low voltage will not

trip relay,

2. Windings burned out

or open,

3. Starting relay not

operating.

1, Motor overloaded.

2, Improper cooling. (Air

circulation restricted

through motor due to

sawdust, accumulating

inside of saw).

1. Burned relay contacts

(due to extended

hold-in period,_caused

by low line voltage, etc.)

2. Saw not in upright

position.

3, Loose or broken

connection_

1. Starting relay not

operating.

2. Voltage too low to permit

motor to reach operating

speed.

3. Fusesor circuit breakers

do not have sufficient

capaciw.

1. Motor overloaded.

2. Fusesor circuit breakers

do not have sufficient

capacity.

3. Starting relay not

operating (motor does

not reach normal speed).

REMEDY

1. Request voltage check from the power company.

2. Have motor repaired or replaced,

3. Have relay replaced.

1. Feed work slower into blade.

2. Clean out sawdust to provide normal air

circulation through motor,

See "Maintenance and Lubrication" section.

1, Have relay replaced and request avoltage check

from the power company.

2. Place saw in upright position.

3. Have wiring checked and repaired.

1, Have relay replaced.

2. Request voltage check from the power company.

3. Install proper size fusesor circuit breakers.

1, Feed work slower into blade,

2. Install proper size fusesor circuit breakers.

3. Have relay replaced,

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO. 113.29570 & 113.295750

42 43

34 33 32

38 37 l

_._ 3s

3O 29

20 21

\23

\\\

10 /

17 18

Figure 1

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MOD E L NO. 113.29570 & 113.295750

Always order by Part Number -not by Key Number

FIGURE 1 PARTS LIST

Key Part

No, No. Description

,,,,,,,,,,,

62714

62715

447441

62514

62545

62655

62643

30540

STD 551225

62642

62636

52644

139331

STD 551012

STD541025

STD 523110

62541

60313

62542

STD 551031

STD 551231

STD 541231

6TD 600603

62441

37818

62652

62539

62710

Gauge Assembly, Miter (See Figure 4)

Fence Assembly, Rip (See Figure 3)

Screw, Fiat Hd, Type "T" 10-32 x 7/8

Insert Assembly (Includes Key No. 5)

Clip, Retaining

Guard Assembly (See Figure 5)

Clamp, Spreader

Screw, Wing 1/4-20 x 1/2

* Lockwasher, External Tooth 1/4

Support, Spreader

*Nut, Square 1/4-20

Bracket

Screw; Set Hex Cup 1/4-20 x 7/8

*Washer, t7/64 x 9/16 x 1/!6

*Nut, Hex 1/4-20

Screw, Hex Hd. 5/16;18 X 1

Bar, Fence Rear

Nut, Self Threading

Rod, Separation

Washer, 21/64 x 5/8 x 1/16

*Lockwasher, External Tooth 5/16

*Nut, Hex, 5/16-18

Screw, Type "T'" Pan Hd. 6-32 x 3/8

Cord with Plug

Relief, Strain

Plate, Cover

Spacer, Fence Guide Bar

Tape, Fence

*Standard Hardware Item -- May be Purchased Locally.

Key Part

No. No.

29 62709

STD 523115

62505

62267

62442

60256

STD 551025

60314

STD 551208

STD 610805

STD 600602

62686

62689

STD 511107

STD 551210

62713

6O354

62712

62204

STD 610802

62452

9TD 541025

3540

63062

30505

37911

62717

62716

Description

Bar Assembly, Fence Guide

(includes Key No. 28)

*Screw, Hex 5/16-18 x 1-I/2

eMotor and Control Box

Clip, Capacitor

Switch, Locking

Key, Switch

*Washer, 17/64 x .734 x.062

Screw, Truss 1/4+20 x 5/8

*Lockwasher, External Tooth No. 8

Screw, Pan Hd+, Type "'AB" No+8x1/2

*Screw, Type 23, Pan Hd., 6+32 x 1/4

Scale, Adjustable Bevel

Handwheel Assembly

*Screw, Pan Hd. 10-32 x 3/4

*Lockwasher, External Tooth No, 10

Panel, Trim

Nut, Speed No. 8

Panel, Front

Clip, Cord

*Screw, Pan Hd., Type B, No. 8 x 5/16

Clamp, Relay

Nut, Hex 1/4-20

Wrench, Arbor

Wrench, Shaft

Wrench, Hex "L'" 1/8

Wrench, Hex "L" 3/16

Bag of Loose Parts (Not Illustrated)

Owners Manual (Not Illustrated)

oAny attempt to repair this motor may create a HAZARD

unless repair is done by a qualified service technician.

Repair service is available at your nearest Sears Store.

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO. 113.29570 & 113,295750

II 3:3

4 5

9 •

*if this part is removed.

discard and reptace with

a new relearningring,

F_ure 2

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO. 113.29570 & 113.295750

FIGURE 2 PARTS LIST

Key Part

No. No, Description

62628

805297-1

STD 511107

STD 541110

STD 551210

62648

62629

62624

62505

62498

62683

60175

6362

60303

62681

60328

62647

STD 551037

60301

62682

62649

STD 511110

Table, Saw

Screw, Fiat Hd. 5/16-18 x 1-1/4

*Screw, Pan Hd. 10-32 x 3/4

*Nut, Hex No. 10-32

*Lockwasher, External Tooth No. 10

Washer, Rubber

Support, Rod

Rod, Cradle

oMotor and Control Box

Collar, Blade

Collar, Stop L.H.

+Blade, Saw 10 inch

Nut, Arbor

Spacer

Nut, Elevation Pivot

Washer, Nylon

Washer, Rubber

*Washer, ,380 x 47/46 x 1/16

*Ring, Retaining 3/8

Screw Assembly, Elevation

Grommet, Rubber

*Screw, Pan No. I0-32 x 1

Key Part

No. No.

23 62651

24 60076

25 STD 541425

26 STD 551026

27 8TD 541411

28 STD 551031

29 8TD 523110

30 5TD 601103

31 62487

32 62633

33 STD511105

34 62685

35 62684

36 62437

37 STD 600803

38 62686

39 62436

40 62625

41 62435

42 62623

43 60052

Description

Rod, Motor

I Washer, .505x 1-1/8x 1/16

*Nut, Lock I/4-20

*Washer, 17/64 x .734 x .062

*Nut, Lock 10-32

*Washer, 21/64 x 3/4 x 1/16

*Screw, Hex Washer 5/16-18 x 1

*Screw, Pan Hd. Type "'T"

10-32 x 3/8

Lead with Eyelets

Base, Saw

Screw, Pan H& 10-32 x 1/2

Nut, Bevel Pivot

Screw Assembly, Tilt

Retainer, Bearing

*Screw, Type "'T" Pan 8-32 x 3/8

Indicator, Bevel

Nut

Hanger

Washer, Thrust

Cradle Assembly

*Screw, Fi!lister Hd. 10-32 x 1-1/2

*Standard Hardware Item - May be Purchased Locally,

oAny attempt to repair this motor may create aHAZARD

unless repair is done by aqualified service techincian.

Repair service is available at your nearest Sears Store.

+Stock Item - May be secured through the hardware

departments of most Sears Retail Stores or

Catalog Order Houses.

*If this part is removed, discard and

replace with a new retaining ring.

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO, 113.29570 & 113.295750

10 il

4 5

FIGURE 3 -62715 FENCE ASSEMBLY

Key Part

No. No. Description

-- 62715

162693

262692

3 STD 551031

4 62711

5 60049

6 62527

7 423350

8 62526

9 STD 600805

10 62528

11 62529

12 62531

13 62530

14 62533

15 STD 551210

16 STD 611005

17 62532

Fence Assembly, Rip

Plug, Button

Knob (includes Key No. 1)

*Washer, 21/64 x 1/2 x 1/32

Indicator, Fence

_Screw, Pan Hd. Type "'T'" 4-40x 3/16

Head, Fence

Screw, Sems 3/8-16 x 1/2

Channel, Fence

Screw, Pan Hd. Type "T" 8-32 x 1/2

Spring; Fence Lock

Lock, Rear Fence

Roller, Rear Fence

Rod, Fence Lock

Spring, Head Alignment

(Includes Key No. 17)

*Lockwasher, External Tooth No. 10

*Screw, Type "A" Hex Hd. No; 10 xI/2

Pad; Alignment

*Standard Hardware Item'- May be Purchased Locally.

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO, 113,29570 & 113.295750

11 9 10

FIGURE 4- 62714 MITER GAUGE ASSEMBLY

Key

No,

Part

No,

-62714

1 82683

2 62692

3 STD 551031

4 37883

5STD 600803

6 STD551208

762042

8 62252

962225

!0 STD541231

11 62383

12 60288

Description

,,,,

Miter Gauge Assembly

P_ug,Button

Knob (Includes Key No, 1)

*Washer, 21/64 × 1 x 1/16

Gauge, Miter

*Screw, Pan Head Type "T" _32 X 5/16

*Lockwasher; External No. B

Indicator

Rod Asm, Miter Gauge

{Includes Key No. 9, I0, 11)

Stud, Clamp

*Nut, Hex Jam 6/16-18

Stud,Pivot

Screw, Lockir_ Set 1/4-20 × 3/8

*t_tandard Hardware Item - May be Purchased Locally.

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO_ 113.29570 & 113;295750

*i_this part is removed, discard and

replace with a new push nut.

FIGURE 5 -- 62655 GUARD ASSEMBLY

Key Part

No. No,

62655

62415

62516

62650

STD 541425

62517

STD 512515

62522

62656

62410

62519

62520

62621

STD 651012

60297

STD 581025

Description

Guard Assembly

Guard

Bumper, Snap In

*Nut, Lock 1/4-20

Link, Guard

*Screw, Pan Hd., 1/4-20 x1-1/2

Spacer; Link

Blade, Spreader

Pin, 1/4 x 1-3/64

Spring, Pawl

Spacer, Pawl

Pawl

*Washer, 17/64 x 1/2 x 1/32

*Nut, Push

*Ring, Retaining 1/4

*Standard Hardware Item -- May be Purchased Locally.

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO. 113.29570 & 113.295750

4 5

6 5 4 2 1

FIGURE 6 - MODEL 113.295750 ONLY

Key Part

No. No.

60314

62552

62554

STD 551225

STD 541025

62553

STD 541250

803835

62659

Description

Screw, Serrated Truss Hd. 1/4-20 x5/8

Leg

Stiffener, Side

*Lockwasher, Ext. 1/4

*Nut, Hex 1/4-20

Stiffener, End

*Nut, Hex 1/2-13

Foot, Leveling

tBeg of Loose Parts (not illustrated)

* Standard Hardware Items - May be Purchased Locally,

tBagcontains all Loose Parts for both Legsand Extensions

PARTS LIST FOR CRAFTSMAN 10 INCH MOTORIZED SAW

MODEL NO. 113.29570 & 113.295750

SAW TABLE

{REF)

11 ,%

FIGURE 7 -- TABLE EXTENSION FOR MODEL 113.295750 ONLY

No,

-- 62546

1t 60323

2 62547

3 ! 62549

1 4 62548

5 STD 541025

6 STD 551225

762550

Part

No, .,,,,,,,,,.,.. Description

Extension Assembly, Complete

Screw, Serrated Truss Hd. 1/4-20 x 1"

Extension

Bracket,Corner Support No, 2

Bracket, Corner Support No. 1

*Nut, Hex 1/4-20

*Lockwasher tExt. I/4

Bracket, Corner Stiffener

HARDWARE FOR ATTACHING

8 STD523112

9 STD 551031

10 STD 551131

11 STD541031

62659

EXTENSION TO TABLE

*Screw, Hex Hal. 5/16-18 XI-I14

*Washer, 1!/32 x 11/1 6 x 1/16

*Lockwasheri Ext. 5/16

*'Nut, Hex 5/16-18

fBag of Loose Parts (not illustrated)

* Standard Hardware Item - May be Purchased Locally.

1"Begcontains atl Loose Parts for both Legs and Extension.

NOTES

Sears I

owners

manual

SERVICE

MODEL NO.

113.29570

SAW ONLY

113.295750

SAW WITH LEGS AND

TWO TABLE EXTENSIONS

HOW TO ORDER

REPAIR PARTS

10 INCH MOTORIZED TABLESAW

Now that you have purchased your 10 inch motorized table saw

should a need ever exist for repair parts or service, simply

contact any Sears Service Center and most Sears, Roebuck and

Co. stores. Be sure to provide all pertinent facts when you call

or visit.

The model number of your 10 inch motorized table saw will be

found on aplate attached to your saw, at the right-hand side of

the base.

WHEN QRDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

PART NUMBER

MODEL NUMBER

113,29570

113.295750

PART DESCRIPTION

NAME OF ITEM

IO-INCH MOTORIZED TABLE SAW

All parts listed may be ordered from any Sears Service Center

and most Sears stores. If the parts you need are not stocked

locally, your order will be electronically transmitted to a Sears

Repair Parts Distribution Center for handling.

Sold by SEARS, ROEBUCK AND CO.. Chicago. IL. 60684 U.S,A.

PartNo. 62716 Form No. SP4319-1 Printed in U.S.A. 7/79

Craftsman 11329570 User Manual 10 INCH MOTORIZED SAW Manuals And Guides L0807115

CRAFTSMAN Saw Table Manual L0807115 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation