Craftsman 137215360 User Manual 4 X 36 BELT/DISC SANDER Manuals And Guides L0803611

CRAFTSMAN Sander Manual L0803611 CRAFTSMAN Sander Owner's Manual, CRAFTSMAN Sander installation guides

User Manual: Craftsman 137215360 137215360 CRAFTSMAN 4 X 36 BELT/DISC SANDER - Manuals and Guides View the owners manual for your CRAFTSMAN 4 X 36 BELT/DISC SANDER #137215360. Home:Tool Parts:Craftsman Parts:Craftsman 4 X 36 BELT/DISC SANDER Manual

Open the PDF directly: View PDF PDF.
Page Count: 10

@
4" × 36" Be_t
6" Disc
/
_lod÷_ No,
!37o2t5360
R
@
CAUT_©N:
Before using this Belt /Disc Sander,
read this manuai and follow
all its Safety Rubs and
Operating _nstructions,
o Safety Instructions
o _nstallation
o Operation
o Maintenance
o Parts List
o Espa_oi
1°81@°848=1882
Sears, Roebuck and Co_ Hoffman Estates_ _L (}0!79 USA
Part No, 1372t5360001
SECTION PAGE
Warranty .................................................................. 2
Product Specifications ....................................................... 2
Safety Rnstructions .......................................................... 3
Accessories and Attachments ................................................. 6
Carton Contents ............................................................ 6
Know your Belt !D]sc Sander .................................................. 7
AssembJy and Adjustments ................................................... 8
Operation ................................................................. 14
Maintenance ................................................. , ............ 16
Troubleshooting Guide ...................................................... 17
Parts ..................................................................... 18
MOTOR ................. 120',/, 60 HZ, 4.2 AMPS
HORSEPOWER ........... 2/3 (Max. Developed)
SPEEDS:
MOTOR .............. 3450 RPM
BELT ................ 1760 FPM
DISC ................ 2800 RPM
SIZES:
BELT ................ 4" X 36"
DISC ................ 6"
TABLE .................. DISC /BELT
TABLE TILT .............. 0° TO 45°
BELT ARM TILT ........... 0° TO 90°
MITER GAUGE ........... YES
To avoid electrical hazards, fire hazards, or damage to the
tool, use proper circuit protection.
Your bench belt/disc sander is wired at the factory for
120V operation. Connect to a 120V, 15 amp branch circuit
and use a 15 amp time delay fuse or circuit breaker. To
avoid shock or fire, replace power cord immediately if it is
worn, cut or damaged in any way.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known [to the State of California] to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
¢ Lead from lead-based paints.
¢ Crystalline silica from bricks, cement and other masonry products.
€ Arsenic and chromium from chemically4reated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals:work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
GENERAL SAFETY INSTRUCTIONS
BEFORE USING THE BELT/DISC SANDER
Safety is a combination of common sense, staying alert
and knowing how to use your belt /disc sander.
To avoid mistakes that could cause serious injury, do not
ptug the belt /disc sander in until you have read and
understood the following:
1.
2_
3.
.
READ and become familiar with this entire instruction
manual. LEARN the tool's applications, limitations, and
possible hazards.
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES,
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
6_
.
DON'T USE IN A DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted.
KEEP CHILDREN AWAY,All visitors should be kept at
a safe distance from the work area.
7,
8.
9.
I0.
MAKE WORKSHOP KID PROOF with padlocks, master
switches, or by removing starter keys.
DON'T FORCE THETOOL. It will do the job better
and safer at the rate for which it was designed.
USE THE RIGHTTOOL, Don't force tool or the
attachment to do a job for which it was not designed.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss
of power and overheating. The table on page 5 shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
11. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
SAVE THESE
t2.
13.
14.
15.
16,
17.
18.
19.
20.
2t.
22.
23.
w_A_ Your ALWAYS WEAR EYE
PROTECTION. Any belt /disc
sander can throw foreign
objects into the eyes which
could cause permanent eye
damage. ALWAYS wear Safety
Goggles (not glasses) that
comply with ANSI safety standard Z87.1. Everyday
eyeglasses have only impact-resistant lenses, They
ARE NOT safety glasses. Safety Goggles are available
at Sears. NOTE: Glasses or goggles not in compliance
with ANSt Z87.1 could seriously hurt you when they break.
WEAR A FACE MASK OR DUST MASK.
Sanding operation produces dust,
SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and it
frees both hands to operate tool.
DISCONNECT TOOLS before servicing, and when
changing accessories, such as blades, bits, cutters,
and the like.
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure the switch is in OFF position before
plugging in.
USE RECOMMENDED ACCESSORIES. Consult the
owner's manual for the recommended accessories.
The use of improper accessories may cause risk of
injury to persons.
NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting toot is unintentionally
contacted.
CHECK FOR DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it wilt operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
NEVER LEAVE TOOL RUNNING UNATTENDED,
TURN THE POWER OFF. Don't leave the tool until
it comes to a complete stop.
DON'T OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories,
DO NOT use power tools in the presence of flammable
liquids or gases.
INSTRUCT ONS
3
24.DONOToperatethetoo!ifyouareundertheinfluence 12.ALWAYSmaintaina minirnumclearanceof 1/16inch
ofanydrugs,alcoholo1"medicationthatcouldaffect orlessbetweenthetableorbackstopandthesanding
yourabilityto usethetoolproperiy, beltordisc.
25. Dustgeneratedfromcertainmaterialscanbe -13.
hazardous to your health. Atways operate the
belt/disc sander in a well-ventilated area and provide
for proper dust removal. Use dust collection systems !4..
whenever possible.
DO NOT sand pieces of material that are too small to
be safely supported.
KEEP fingers away [rom where the belt goes into the
dusl trap.
SPECHF C SAFETY NSTRL CTIONS
FOR BELT /DISC bANDERs'- " "
For your own safety, do not try to use your belt/disc sander
or plug it in until it is comple[ely assembled and installed
according to the instructions, and until you have read and
understood this instruction manual:
.THiS SANDER tS DESIGNED TO SAND WOOD OR
WOOD-LIKE PRODUCTS ONLY. Sanding or grinding
other materials could result in fire, injury or damage to
workpiece.
2,
,
15.
16.
17.
i8.
19.
USE sander on horizontal surfaces only. Operating
the sander when mounted on nonqqerizontal surfaces
might result in motor damage. 20.
TO STOP i[ from tipping over or moving when in use,
the sander must be securely fastened to a bench top
or supporting surface.
PLACE the sander so neither the user nor bystanders
are forced to stand in line with the abrasive belt or disc.
5. MAKE SURE the sanding belt is installed in the correct
direction. See directional arrow on back of belt.
ALWAYS have the tracking adjusted properly so the
belt does not run off the pulleys.
DO NOT USE sanding belts or discs that are damaged,
torn, loose. Use only correct size sanding belt and disc.
Narrower belts uncover parts that could trap fingers.
MAKE SURE there are no nails or foreign objects in
the part of the workpiece to be sanded.
ALWAYS HOLD the workpiece firmly when sanding•
Keep hands away from sanding belt or disc. Sand
only one workpiece at a time.
.
7_
,
9.
10. ALWAYS HOLD the workpiece firmly on the table
when using the disc sander and when using the belt
sander.
21.
22.
23.
24.
WHEN sanding a large workpiece, provide additional
support at table height.
DO NO'[' sand with the workpiece unsupported.
Support the workpiece with the backstop or table. The
only exception is curved work performed on the outer
sanding drum. Plan your work support
NEVER USE ANOTHER PERSON as additional
support for a workpiece longer or wider than the table.
ALWAYS remove scrap pieces and other objects from
the table, backstop or belt before turning the sander
ON.
NEVER perform layout, assembly or set-up work on the
table while the sander is operating.
NEVER use solvents Io clean plastic parts. Solvents
coutd dissolve or other wise damage the material. Use
only a soft damp cloth to clean plastic parts.
SHOULD any part of your sander be missing, damaged,
or fai! in any way, or any electrical components fail to
perform proper!y, shut off switch and remove plug from
power supply outlet. Replace missing, damaged or
failed parts before resuming operation.
NEVER PULL°THE POWER CORD out of the receptacle.
Keep cords away from heat, oil and sharp edges.
HAVE AN ELECTRiCiAN REPLACE OR REPAIR
damaged or worn cords immediately.
When using the bett to grind or sharpen metal or
plastic material:
o DO NOT wet grind or polish. Never use a steady
stream of water on the workpiece. Dip or quench
the workpiece in water Io cool it.
o DO NOT OVERHEATTHE WORKP_BCE. Move
meta the material across the abrasive and al!ow
it to coo} when it becomes hot.
• 3
o DO NOT grind or pol s_ magnestum. It could
CATCH on fire.
11. ALWAYS SAND ON THE DOWNWARD S_DE of the
sanding disc when using the disc sander. Sanding on
the upward side of the disc could cause the workpiece
to fly out of position, resuking in injury.
SAVE THESE NSTRUCT ONS
GROUNDING DNSTRUCTIONS
IN THE EVENT OF A MALFUNCTmONOR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This tool is
equipped with an electric cord that has an equipment
grounding conductor and a grounding plug. The plug
MUST be plugged into a matching receptacle thai is
properly installed and grounded in accordance with ALL
local codes and ordinances.
DO NOT MODIFYTHE PLUG PROVIDED. If it will not fit the
receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor with the green insulation (with or without yellow
stripes) is the equipment grounding conductor. If repair or
replacement of the electric cord or plug is necessary, DO
NOT connect the equipment grounding conductor to a live
terminal.
CHECK with a qualified electrician or service personnel if
you do not completely understand the grounding instructions,
or if you are not sure the tool is properly grounded.
USE ONLY 3-W_RE EXTENS!ON CORDS THAT HAVE
3-PRONG GROUNDING PLUGS AND 3-POLE
RECEPTACLES THAT ACCEPT THE TOOL'S PLUG.
REPAIR OR REPLACE DAMAGED OR WORN CORD
IMMEDIATELY,
GUIDELINES FOR EXTENSION CORDS
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord wilt
cause a drop in line voltage resulting in loss of power and
overheating. The table below shows the correct size to use
depending on cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Be sure your extension cord is properly wired and in
good condition. Always replace a damaged extension cord
or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit
must not be less than #!2 wire and should be protected
with a 15 Amp time lag fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric current is rated the same as the
current stamped on the motor nameplate. Running at a
lower voltage will damage the motor.
SAVETHESE
This tool is intended for use on a circuit that has a
receptacle like the one illustrated in FIGURE A.
FIGURE A shows a 3-prong electrical plug and receptacle
that has a grounding conductor. If a properly grounded
receptacle is not available, an adapter (FIGURE B) can
be used to temporarily connect this plug to a 2-contact
ungrounded receptacle. The temporary adapter should be
used only until a properly grounded receptacle can be
installed by a qualified technician. The adapter (FAGURE B)
has a rigid lug extending from it that MUST be connected
loa permanent earth ground, such as a properly
grounded receptacle box. The Canadian Electrical Code
prohibits the use of adapters.
CAUTmON: In all cases, make certain the receptacle in
question is properly grounded. If you are not sure have a
certified electrician check the receptacle.
This belt /disc sander is for indoor use only. Do not
expose to rain or use in damp locations.
Fig, A
3-ProngPlug
._...,... Grounding Prong
Properly Grounded
3-Prong Receptacle
Fig. B
Grounding Lug _
I ake Sure This
is Connected to a
Known Ground
2-Prong
Receptacle
This tool must be grounded while in use to protect the
operator from electrical shock.
{when using 120 voits only)
_.mpe:e,_e_!qg
more than not more _hal;
0 6
6 10
t0 t2
12 16
Totallength of cord in feet ,,
25' 50' 100' 150'
18 16 16 14
18 16 14 i2
16 16 14 12
14 12 Notrecommended
NSTRUCT ONS
AVAHLABLE ACCES._ ,OR ES
Use only accessories recommended for this belt /disc
sander. Follow instructions that accompany accessories.
Use ol improper accessories may cause hazards.
Visit your Sears Hardware Department or see the Sears
Power and Hand Tool Catalog for the following
accessories:
o Adhesive-backed Discs 6 inch:
Fine, Medium, or Coarse Griics
o Sanding Belts 4 x 36 inch:
Fine, Medium, Coarse, or Extra Coarse Grits
oAbrasive Disc & Belt cleaner
Use only accessories designed for this belt /disc sander to
avoid injury from thrown broken parts or workpieces.
Sears may recommend other accessories not listed in this
manual. See your nearest Sears store or Power and Hand
Tool Catalog for other accessories.
Do not use any accessory unless you have completely
read the instruction or owner's manual for that accessory.
If any part is missing or damaged, do not plug the belt /
disc sander in until the missing or damaged part is
replaced, and assembly is complete.
Carefully unpack the belt /disc sander and all its parts,
and compare against the illustration below.
To protect the belt /disc sander from moisture, a
protective coating has been applied to the machined
surfaces. Remove this coating with a soft cloth moistened
with WD-40.
To avoid fire or toxic reaction, never use gasoline, naphtha,
acetone, lacquer thinner or similar highly volatile solvents
to clean the belt /disc sander.
_EM
A.
B.
C.
D.
E.
R
G.
H,
I.
J.
K.
L.
M.
N.
O.
R
Q.
R.
DESCRiPTiON _QUANTITY
Belt /Disc Sander 1
Disc 1
Disc housing 1
Disc table 1
k/liter gauge 1
Disc dust chute 1
Belt dust chute 1
Loose parts in bag:
"Fablesupport rod 1
Belt backstop 1
Hex key 1
Open-end wrench 1
Hex head bolt t
Long pan head screw 40mm 1
Pan head short screws 2
Pan head thin screws 1/2" 2
Pan head medium screws 12ram 1
Large washer 1
Small washers 2
B
c
G
H I L M
N O
@ @@
Q R
6 ::: : :: : : : ::: ::: : ;:::::::::::
Sanding disc
\Disc housing Back stop Tension lever Sanding belt
Table assembly
Disc dust chute
Hex key
: : : : :: ::,::: :: :::
Idler drum
Bett tracking knob
stop
Mounting hole
On/Off switch
_tor_ge Miter gauge
J
Table support rod
Table Iock knob
Bevel scale
7 :!' ::_ :i
ASSEMBLY INSTRUCTIONS
To avoid injury, always keep the plug disconnected from
the power source and the switch turned OFF until the
sander is completely assembled and adjusted properly.
For your own safety, never connect plug to power source
outlet until all assembly and adjustment steps are
completed, and you have read and understood the safety
and operating instructions.
TOOLS NEEDED
Slotted screwdriver
Phillips screwdriver
Adjustable wrench
Level
Combination square
MOUNTING BELT AND DISC SANDER TO
WORKBENCH (FIG. B)
Fig. B
2
1. belt /disc sander base 3......._"'f_
2. Bolt 4
3. Flat washer / ri .......
4. Rubber washer 1 mUm I I
5. 1/2" Foam pad (optional) [ i i
6. Worksurface
7. Flat washer
8. Lockwasher
9. Hex nut (
10. Jam nut
t J-
i
5
7 ......
t0
PULLEY BELT ADJUSTMENT (FIG. C AND D)
1. Loosen the two hex screws (1) with wrench provided,
and move the sanding arm (2) to the vertical position.
Then tighten the two screws. (Fig. C)
2. Loosen lock nut (3), and belt tension set screw (4) by
turning it counterclockwise.
3. Raise up on the motor pulley (5) to replace or remove
the existing belt. Place new belt (6) on both pulleys (5)
and (7)•
4. At the center span of the pulleys, apply light pressure
to the belt. At the same time tighten set screw (4) by
turning it clockwise, until the belt is just stretched.
Reapply light pressure to the belt and maintain belt
tension between t/4" to !/2" deflection.
5,
IMPORTANT: Do not over tighten belt tension because
it does not require excessive tension to function
properly• Excessive tension will reduce motor and
belt life.
After correct tension is obtained tighten lock nut (3), and
position sanding arm (2) in the horizontal position by
loosening the two hex screws (1). Retighten hex screws•
Fig, D
6
5
PULLEY COVER INSTALLATION (FIG. E)
Attach pulley cover (1) using the 40mm long pan head
screw (2) and 12mm pan head screw (3), as shown.
Tighten screws securely.
Fig. E _ 3
i
SANDING DiSC iNSTALLATION (FIG. G)
Remove and clean any adhesive or material left on the
disc plate (2). Peel plastic backing from abrasive disc (1)
and carefully press disc firmly in position around the
sanding disc.
Fig. G
©
SANDING DiSC PLATE INSTALLATION (FIG. F) ,_ '<
1. Thread 1/4" set screw (1), into the tapped hole on hub
of sanding disc plate (2). Turn clockwise to tighten.
2. Slide sanding disc plate (2), on drive shaft (3) making
sure flat on drive shaft is aligned with set screw (1) in
hub of disc plate (2). Stide disc plate onto shaft until
disc plate surface and edge of the pulley cover are
nearly flush.
3. Insert hex wrench, down through slot (4) in the top of
belt and pulley guard and tighten set screw (I) against
flat on drive shaft (3).
4
1
DISC COVER INSTALLATION (FIG. H)
1. Position disc cover (1) in place as shown.
2. Insert the two 1/2" pan head screws (2) and tighten.
2
TABLE ASSEMBLY INSTALLATION (FIG. I)
The worktable can be used with either the sanding disc or
the sanding belt. It should be used to support workpieces
in all sanding operations except inside curve applications.
1. Insert the table support rod (1) into the sander base
hole as shown. Table support rod should extend
5" outside of the sander base.
2. Align round side of the support rod (1) with hex bolt (2)
and tighten bolt.
3. Slide table assembly (3) onto rod (1).
4. Adjust table, align flat side of support rod with hex
boJt (4) on tabte bracket, and tighten.
Fig. U
Fig. J
DUST CHUTE _NSTALLATtON (RG. K)
1. Position the dust chute (1) on the sanding arm as
shown.
2. Place washers on two pan screws (2). insert the screws
through the slots on the side of the dust chute into the
threaded holes on the sanding arm (3).
3. Tighten screws securely.
Fig. K
To avoid trapping the workpiece or fingers between the
table and sanding disc, the table edge should be
positioned a maximum of 1/16" from sanding disc plate,
as shown in FIG. I.
BACK STOP INSTALLATION (FIG. J)
The backstop prevents the workpiece from being pulled or
dragged beyond the sanding arm. It should always be
used to help control the workpiece.
1. Position back stop (1) on sanding arm (2).
2, Place washer (3) on hex bolt (4). Insert bolt through
slotted hole into the threaded hole in the side of the
sanding arm.
& Tighten hex bolt securely.
::: : =i ::= : : i : t0 = : :: :: =:
ADJUSTMENTS
To avoid injury, always keep the plug disconnected from
the power source and the switch turned OFF until the
sander is completely assembled and adjusted properly.
ADJUSTRNG TABLE SQUARE WITH SANDING DiSC
(F_G. L)
1. Using a combination square (1), place one side of the
square on the table (2) with the other side against the
sanding disc (3), and check to see if the table is 900
to the disc.
2. if the table surface is not 90° to the disc, loosen table
lock knob (4), adjust table square with disc and tighten
iock knob (4).
3. Adjust pointer (5) to the 0Gmark on [he angle scale,
using a screwdriver.
Fig. L
FIIt II _ llf_I
4
O
To avoid trapping the workpiece or fingers between the
table and sanding disc, the table edge should be
positioned a maximum of 1/16" from sanding disc plate.
ADJUSTING TABLE TO BE HORIZONTAL (FIG. I_A)
1. Place level on table parallel to disc.
2. If not level, hold table, loosen bolt (1).
3. Adjust to horizontal and retighten bolt.
L': : i-_ib: : <: ¸ :::. : -i ! /? ....
ADJUSTING TABLE ANGLE (FIG. N)
The table can be tilted [rom 0° to 45° by loosening the
tabte lock knob (1), tilting the table to the desired angle,
and tightening table lock knob (1).
After tilting the table, the table assembly must be
repositioned on the support rod to a maximum of 1/16"
distance between the sanding disc and the edge of the
table, to avoid trapping the work or fingers between the
disc and table.
Fig. N
1t ....
SAFETY POWER SWITCH (FIG. O)
To avoid injury, always keep the plug disconnected from
the power source and switch turned OFF until the sander
is completely assembled and adjusted properly.
The ON-OFF toggle switch (1) is located on side of the
sanding machine. Pull toggle switch up to turn the tool ON
and down to turn it OFR The toggle switch has a switch
key (2) for locking the switch in the OFF position.
IMPORTANT: When removing switch key from toggle
switch, always push the switch down to the OFF position
and pull yellow key out.
Fig. 0
WRENCH STORAGE
1/8 INCH HEX WRENCH (FIG. P)
Insert the long end of the hex wrench (1) through the
holes (2) located on the back surface of the pulley cover,
as shown.
Fig. P
WRENCH (F1G. Q)
Insert the handle of the wrench into the metal clip located
on the sander as shown.
Fig, Q
f
o ©
MITER GAUGE (FIG. R)
A miter gauge (1) is supplied with your sander and is
used with the disc table. The miter gauge body can be
tilted 0° to 45° right or left for angle or miter sanding.
Install the slide rod into the table slot (2) as shown.
Loosen lock knob (3), rotate miter gauge body to the
desired angte and tighten lock knob (3),
Fig, R
1 3
12 : :
REPLACmNG SANDING BELT (FIG. S, T, U)
To avoid injury, turn switch OFF and disconnect the plug
from the power source before removing and installing
sanding belts.
1. Remove two screws (1), and dust chute (2).
Fig, S
2. Remove hex bolt (3), and backstop (4)•
Fig. T 3 4
3. Slide tension lever (5), to the right to release tension
on the sanding belt (6) (Fig, U),
4. Remove sanding belt from both sanding drums (7).
5. Slide new sanding belt over sanding drums, making
sure the belt arrow located on the inside of the belt will
run in the direction of the arrow on the sander• Slide
tension lever (5), to the left to apply belt tension.
6, Quickly push the belt forward by hand (in the direction
of the belt rotation arrow, visible from the top between
the sanding disc and the belt arm) and check to see if
the sanding belt tends to run to one side or the other
on the two pulleys.
7. If the sanding belt runs toward the disc, slightly turn
the tracking knob (8) counterclockwise.
8. If the sanding belt runs away from the disc, slightly
turn the tracking knob (8) clockwise.
9. Plug sander into power source and turn the switch
ON and OFF quickly, and check to see if the
sanding belt runs to either side. Readjust and fine tune
tracking knob if necessary.
10. When proper tracking is achieved, replace backstop
and dust guard.
Fig. U
CHANGING POSITION OF SANDING ARM
SANDING ARM IN VERTICAL POSITION (FIG. V)
1. The sanding arm can be used in either the horizontal
or vertical position. To move the sanding arm, loosen
the two bolts (1), that attach arm (2). Move the arm to
the desired position. Tighten the two bolts.
2. Insert the table support rod (3) into auxiliary hole as
shown. Table support rod should extend 5" outside
base.
3. Align round on support rod with hex bolt on sander
and tighten hex bolt (4) on sander.
4. Slide table assembly (5) onto rod (3), as shown.
5. Align flat on support rod with hex bolt (6) on table
bracket and tighten bolt.
To avoid trapping the workpiece or fingers between the
table and sanding belt, the table edge should be
positioned a maximum of 1/16" from sanding belt.
Fig. V
6
13 i_?!_!_;_i_iYF_!!!_!;_J:_!!_!!_i!_!_!i!i!:_i_!:!i_!_:!!_i_?:i_ii!_!_!_!;_i_:_!!i_!_?_i!_i!i!
ADJUSTINGSANDINGARM
LEVELINGTHEARM(FIG.W)
A positivestopisprovidedto positionthesandingarm
levelwiththeworkbenchwhenthearmisinthe
horizontalposition.
1. Placethesandingarm(1)inthehorizontalposition.
2. Placealevel(2)onthesandingbeltandchecktosee
if thearmis level.
3. Ifanadjustmentisnecessary,loosenlocknut(3),and
turnsandingarmstop(4)clockwisetoraise,or
counterclockwiseto lower,untilthesandingarmis
level.Thentightenlocknut(3).
Fig. W
2 1
The belt and disc sander is designed to perform rough
sanding operations on surface, edge grain and end grain
sanding. The sander will also perform freehand forming
and contouring operations. The following suggestions are
recommended for best results and safest use.
1. Always apply light pressure allowing the abrasive to
remove the material slowly.
2. The workpiece should be moved, continuously, to
avoid burning.
3, Avoid sanding small pieces of wood which will
position the fingers close to the abrasive belt or disc.
USING BACKSTOP WITH SANDING ARIVl (FIG. X)
When using the sanding arm in the horizontal position, to
perform surface or edge sanding, the backstop (1) must
always be used. Always hold the work piece (2) firmly
keeping your fingers away from the sanding belt (3).
Always keep the end of the workpiece against the
backstop and move the work evenly across the sanding
belt. Apply only enough pressure to allow the sanding
belt to remove material, Use extra caution when sanding
very thin piece&
The edge of the backstop must be positioned a maximum
of 1/16" from the sanding belt to avoid trapping the work
or fingers between the backstop and sanding belt.
Fig. X
SANDING INSIDE CURVES (FIG. Y}
Freehand sanding of inside curves can be sanded on the
idler drum (1). Never attempt to sand the ends of a
workpiece on the drive drum.
To avoid injury, do not apply the end of the workpiece to
the idler drum. This could cause the workpiece to fly up
or cause kickback.
Fig. Y
SANDING OUTSIDE CURVES (FroG.Z)
Freehand sanding of outside curves should be done on
the sanding disc (1). Keep fingers a minimum of 1 inch
from the disc.
Always sand on the left (downward) side of the sanding
disc, as shown. Sanding on the right (upward) side of the
sanding disc could cause the workpiece to fly up which
could be hazardous.
The edge of the table must be positioned a maximum of
1/16" from the sanding disc to avoid trapping the
workpiece or fingers between the table and sanding disc,
Fig. Z
END GRAIN SANDING WITH THE BELT (FroG.AA)
When sanding the ends of the wide workpieces it is
more convenient to use the sanding belt (1) with the
sanding arm in the vertical position and the table
assembly (2) moved to the sanding belt, as shown. See
section titled CHANGING POSITION OF SANDING ARM.
For more accurate work use the miter gauge and move
the workpiece evenly across the sanding belt.
WMPORTANT: Use a combination square to position
miter gauge perpendicular to face of the disc. If it is not
square loosen miter gauge knob and move miter gauge,
slightly, until it is square.
For your own safety, turn switch OFF and remove plug
from the power source outlet during assembly or while
making adjustments to belt /disc sander.
The edge of the table must be positioned a maximum of
1/16" from the sanding belt to avoid trapping the
workpiece or fingers between the table and sanding belt.
Fig. AA
For your own safety, turn switch OFF and remove plug
from the power source outlet before maintaining, or
lubricating your belt /disc sander.
1. Frequently blow out or vacuum out any dust that may
accumulate inside the motor.
2. Remove impacted sawdust from the disc and belt
abrasive or replace abrasive.
Certain cleaning agents and solvents damage plastic
parts. Some of these are: gasoline, carbon tetrachioride,
chlorinated cleaning solvents, ammonia and household
detergents that contain ammonia. Avoiding use of these
and other types of cleaning agents, minimizes the
probability of damage.
To avoid shock or fire hazard, if the power cord is worn or
cut or damaged in any way, have it replaced immediately.
All repairs, electrical or mechanical, should be attempted
only by trained repairmen. Contact the nearest Sears
Service Center.
LUBRaCATION
All of the BALL BEARINGS are packed with grease at
the factory. They require no further lubrication.
TROUBLESHOOTUNG GUIDE
Turn switch OFF and always remove plug from power source before making any adjustments or repairs.
All repairs, electrical or mechanical, should be attempted only by qualified service technicians. Contact the nearest
Sears Service Center.
PROBLEM
Motor will not run.
PROBABLE CAUSE REMEDY
1, Defective or broken ON/OFF switch.
2. Defective or damaged switch cord.
3. Defective or damaged switch relay.
4. Burned out motor.
5. Blown house fuse.
1-3. Replace all broken or defective
parts before using sander.
4,
.
Machine slows down t. Operator applying too much 1.
while sanding, pressure to workpiece,
2. Dirt on wheels. 2.
3. Worn or stretched belt. 3.
Sanding belt runs off pulleys. 1. Not tracking properly. 1.
Wood burns while sanding. 1. Sanding disc or belt glazed with sap. 1.
2. Excessive pressure being applied 2.
to workpiece.
Motor overheats 1. Motor overload. 1.
Consult your local Sears Service
Center. Any attempt to repair this
motor may create a hazard unless
repair is done by a qualified
technician.
Replace house fuse. Turn OFF
other appliances and power tools
on the same circuit.
Use less pressure in applying
workpiece to sanding surface.
Clean wheels.
Replace pulley belt.
Adjust tracking. See section
"REPLACING SANDING BELT".
Replace belt or disc.
Reduce pressure applied to
workpiece.
Reduce motor load. Allow
to cool off before restarting.
4" x 36" BELT/DISC SANDER MODEL NO. 137.215360
4" x 36" BELT/DDSC SANDER MODEL Nee 137.215360
When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause
product damage.
Any attempt to repair or replace electrical parts on this belt /disc sander may create a HAZARD unless repair is
done by a qualified service technician, Repair service is available at your nearest Sears Service Center.
Always order by PART NUMBER, not by key number
Key No. Part No. Description Size Qty, Key No, Part No. Description
1 2668BBDA37 Pan hd. screw M6x1,0-8 4 81 270tQBD514 Hex. nut
2 15900204 Floor p{ate 1 62 N/A
3 2601BZDA47 Hex. hd. boll M6xl.0 1 63 16001701 Spring
4 2701FZDt06 Hex nut M6xl.0 '1 64 15902001 Guide drum
5 15904102 Motor pulley 1 65 2705QZB506 Nut chuck
6 8343725904 Motor t 66 2601QBD K37 Hex, hd, boil
7 15900702 Motor rod 1 67 2502NBC406 Spring washer
8 2570BBN207 E-ring t 68 16003001 Grips
9 15900904 Base 1 69 16002901 Belt tension lever
I0 2898DB7G06 Rocker switch 1 70 15902501 Handle
Size
t/2x13
1/4x20
"1/4x20
Qty.
1
t
t
1
1
1
I
1
1
t I 2652PBCK1 t Pan hd. tapping screw M4xl 8q 2 2 71 15904001 Plastic wasl_er
12 15901204 Switch cover 1 72 2501NBDN16 Fiat washer
13 2852PSCK10 Pan hd. tapping screw M4xt 8-8 2 73 16002301 Spring
14 2504MZCO04 External tooth lock washer 2 74 1590170t Rubber pad
15 15903101 Switch box 1 75 2570BBNt 12 C-ring
16 2801UBHA07 Strain relief 2 76 2506MBN612 Wave washer
17 t 5901704 Label 1 77 1590I 801 Bush
18 2668BBDA37 Pan hd. screw M6x1.0-8 4 78 15901902 Drum4d[er
19 15901903 Plate cover 1 79 15902101 Shaft-idler
20 26010BDK57 Hex. hd, bolt 5/16xt8,1 1 80 15900801 Sanding bell
1
1
1
2
2
1
2
1
1
1
21 2603BBLA38 Hex. soc. set screw M6xl _0-t 0 1 8! 15905501 Lock kr)ob
22 15902202 Plate cover ! 82 2501QBDK53 Hex. hd. boil 5/16x18-7/16
23 2888BBDA37 Pan hd. screw M6x1,0-8 4 83 2501NBDN24 Flat washer
24 2807BY06H2 Power cable 1 84 16005201 Tilt bracket
25 2606BBLA05 Hex. ace. set screw M4x&7-4 2 85 2668QBDK24 Pan hd. screw 10#x24-I/4
26 2701 FBD106 Hex, nut M6xl.0 1 86 16004901 Needle pointer
27 2669SBDA41 Pan hd. screw M6xt.O-20 1 87 26010BDK55 Hex. hd. bolt 5/16x18-3/4
28 2668QBDK17 Pan hd. screw 8#x32qi2 2 88 16004801 Tabte support
29 1771150l Disc cover 1 89 15908101 Hex. soc. hd. cap bolt 10#x32-0.59
36 15904601 Disc sanding 1 90 2504MB0005 External tooth lock washer
1
1
1
1
1
1
1
1
2
2
31 15904501 Hate sanding I 9I 2501NBDNO3 Flat washer 2
32 2603RBLK32 Hex, soc. set screw 1/4x20-1/4 I 92 15906301 Pin pivot sapport '_ 2
33 2668BBDA45 Pan hd. screw M6x1,0-40 I 93 16004301 Pin pivot 2
34 16005903 Pulley cover 1 94 15906001 7ab}e sander I
35 2138NBL701 Wrench hex. 1 95 15905301 Support rod 1
36 2572ARY150 Synch belt 1 96 14911703 Sheet bar 1
37 15903701 Spindle pulley 1 97 14606001 Angle pointer 1
38 26010BDK59 Hex. hd. boil 5t16x18-1 1/2 2 98 2641BZDA22 Round washer hd. screw M5x0.8-6 1
39 2501NBDN22 Ftat washer 5/16x25/32-1/8 2 99 14607802 Miter gauge 1
40 15904002 Bearing seat bracket I 100 2501NZDN10 Flat washer 1
41 2502ABC416 Spring washer 2 t01 14608301 Knob I
42 2602BBLA55 Hex. sec. hd. cap belt M8xl,25-20 2 t02 14608001 Pin 1
43 15907803 Caution Iabei 1 103 15910601 Wrench 1
44 2669QBDK27 Pan hd. screw 10#x24-3/4 3 104 2620BBDC19 Pan hd. screw & washer M6x1.0-12 2
45 17305801 Bearing seat 1 105 1591080I C_amp 1
46 2001ZZ6001 Ball bearing 2 106 t5911004 Warning label 1
47 2570BBN1 !2 C-ring 2 107 2669BBDA39 Pan hd. screw M6xl.0-12 1
48 15900102 Drive-drum 1 108 2805U5HN18 Terminat 1
49 2603RBLK32 Hex. soc. set screw t/4x20-ti4 2 109 2801DBHAOI Strain relief 1
50 18001203 Table belt 1 110 2606BBLA05 Hex. soc. set screw M4x0.7-4 2
51 15906701 Drive shaft 1 111 28605BH071 Switch key I
52 16001401 Cap.-beari ng 1 112 163t 4801 Power cord cl amp 2
53 2668QBDK22 Pan hd. screw 10#x24-I/4 8 113 264t BBDA40 Round washer hd. screw 2
54 16008101 Dust collector ! 114 250t MZDN06 Hal washer 2
55 250tNBDN03 Flat washer 2 137215360001 Owner's manual 1
56 26680BDK22 Pan hd. screw I0#x24-1/4 2
57 2601QBDK34 Hex. h& belt l/4x20-1/2 t
58 2501NBDN16 Fiat washer 1/4x3/4-1/16 1
59 16003101 Stop back 1 N/A Not applicable
60 15901101 Screw stop 1 Not shown
co
©
to
o
19

Navigation menu