Craftsman 137218010 User Manual TABLE SAW Manuals And Guides L0511162

CRAFTSMAN Saw Table Manual L0511162 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

User Manual: Craftsman 137218010 137218010 CRAFTSMAN TABLE SAW - Manuals and Guides View the owners manual for your CRAFTSMAN TABLE SAW #137218010. Home:Tool Parts:Craftsman Parts:Craftsman TABLE SAW Manual

Open the PDF directly: View PDF .
Page Count: 28

Operator's Manuam

CAUTION:

Before using this Table Saw,

read this manual and follow

all its Safety Rules and

Operating Instructions

o Safety Instructions

o Installation

o Operation

+ Maintenance

o Parts List

Customer Help Line

1 o800o843ol 682

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit our Oraftsman website: www.sears.com/craftsman

Part No. 137218010001

SECTION PAGE

Warranty ........................................................ 2

Product Specifications .................................... 2

Power Tool Safety ........................................... 3

Tabe! Saw Safety ............................................ 4

Electrical Reuirements and Safety .................. 5

Carton Content ................................................ 6

Know Your Table Saw ...................................... 8

SECTION PAGE

Assembly and Adjustments ............................. 9

Operation ........................................................ 17

Maintenance .................................................... 21

Troubleshooting Guide .................................... 22

Push Stick Pattern ........................................... 23

Parts List ......................................................... 24

ONE YEAR FULL WARRANTY

If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears

wil! repair it free of charge. Contact a Sears Service Center for repair.

If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of

purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state

to state.

Sears, Roebuck & Co., Dept. 817 WA, Hoffman Estates, IL 60179

WARNINGn

Some dust crested by power sanding, sawing, grinding, drilling and other construction activities contains

chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

Lead from lead-based paints

Crystalline silica from bricks, cement and other masonry products

Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in s well ventilated ares and work with approved safety equipment such as

dust masks that are specially designed to filter out microscopic particles.

MOTOR

HP (Maximum developed) ......................... 2.5

Type .......................................................... Universal

Amps ......................................................... 13

Voltage ...................................................... 120

Hz .............................................................. 60

RPM (no load) ........................................... 5000

Thermal Overload Protection .................... YES

SAW

Table Extension ............................ Right Side =8 in. Steel

Rip Capacity with Extension ......... 17-1/2 in.

Blade Size .................................... 10 in.

Rip Fence ..................................... YES

Miter Gauge ................................. YES

Maximum Cut Depth @ 900 .......... 3 in.

Maximum Cut Depth @ 450 .......... 2=1/2 in.

Maximum Diameter Dado ............. 6 in.

Maximum Dado Cut Width ............ 1/2 in.

l,&WARNmNGI

To avoid electrical hazards, fire hazards or dsmsge to the table saw, use proper circuit protection.

This table saw is wired st the factory for 110-120 Volt operation, tt must be connected to s 110-120 Volt /

15 Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is

worn, cut or damaged in any way.

Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow

these rules could result in serious injury to you or damage to the table saw.

IAWARNINGU

Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow

these rules could result in serious injury or damage to the table saw.

Good safety practices are a combination of common l& REMOVE ADJUSTING KEYS AND WRENCHES.

sense, staying alert and understanding how to use your

power tool To avoid mistakes that could cause serious

injury, do not plug in your power tool until you have read

and understood the fo!!owing safety rules:

1. READ and become familiar with the entire Operator's

Manual. LEARN the tool's application, limitations and

possible hazards.

]

2. IA WARNING JLookfor this symbol that identifies

important safety precautions. It means CAUTION!

Become alert, your safety is involved if you do not

follow the safety instructions.

3. 1'_ DANGER ILook for this symbol that identifies

important safety precautions. It means CAUTION!

Become alert, your safety is involved if you do not

follow the safety instructions.

4. NEVER OPERATE THIS MACHINE WITHOUT THE

SAFETY GUARD tN PLACE FOR ALL THROUGH°

SAWING OPERATIONS.

5. DO NOT USE tN A DANGEROUS ENVIRONMENTS

such as damp or wet locations or exposure to rain.

Keep work area well lighted.

6. DO NOT use power tools in the presence of

flammable liquids or gases.

7. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

8. KEEP CHILDREN AWAY. All visitors should be kept

at a safe distance from the work area.

9. DO NOT FORCE THE TOOL. It will do the job better

and safer at the rate for which it was designed.

10 USE THE RIGHT TOOL. Don't force the tool or

attachment to do a job for which it is not designed.

11. WEAR PROPER APPAREL. DO NOT wear loose

clothing, gloves, neckties, rings, bracelets or other

jewelry that may get caught in moving parts. Non-

slip footwear is recommended. Wear protective hair

covering to contain long hair.

12. WEAR A FACE MASK OR DUST MASK. Sawing,

cutting and sanding operations produce dusL

l& DISCONNECT TOOLS before servicing and when

changing accessories such as blades, cutters, etc.

Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool before

turning ON.

17. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN THE POWER "OFF". Do not leave the tool

before it comes to a complete stop.

l& NEVER STAND ON TOOL. Serious injury could

occur if the too! is tipped or if the cutting tool is

unintentionally contacted.

19. DO NOT OVERREACH. Keep proper footing and

balance at all times.

20_ MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for most efficient and safest performance.

Follow instructions for lubricating and changing

accessories.

21. CHECK FOR DAMAGED OR LOOSE PARTS.

Before further use of the tool, a guard or other

part that is damaged should be carefully checked

to ensure it will operate properly and perform its

intended function. Check for alignment of moving

parts, binding of moving parts, loose mounting

and any other conditions that may affect its safe

operation. A guard or other part that is loose or

damaged should be properly adjusted repaired or

replaced.

22. MAKE WORKSHOP CHILD PROOF with padlocks,

master switches or by removing starter keys.

2& DO NOT operate the tool if you are under the

influence of any drugs, alcohol or medication that

could impair your ability to use the tool safely.

24. USE A DUST COLLECTION SYSTEM wherever

possible. Dust generated from certain materials can

be hazardous to your health and in some cases, a

fire hazard. Always operate the power tool in a well-

ventilated area with adequate dust removal

25_ ALWAYS WEAR EYE PROTECTION. Any power

tool can throw foreign objects into your eyes which

could cause permanent eye damage. ALWAYS

wear safety goggles (not glasses) that comply with

ANSI safety standard Z87.1. Everyday glasses

have only impact resistant lenses. They ARE NOT

safety glasses. NOTE: Glasses or goggles not in

compliance with ANSI Z87.1 could cause serious

injury when they break.

14. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure the switch is in the OFF

position before plugging into the power supply.

26. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the blade or

cutter only.

15. USE ONLY RECOMMENDED ACCESSORIES.

Consult the Operator's Manual for recommended

accessories. The use of improper accessories may

cause injury to you or damage to the tool

27_ DO NOT AUTHORZE ADDITIONAL USERS to

operate this power tool without the accompanying

operators manual for which the user must read &

understand.

ALWAYSUSESAWBLADEGUARD,splitterand

anti-kickbackpawlsforeveryoperationforwhich

theycanbeused,includingthrough-sawing.

Through-sawingoperationsarethoseinwhichthe

bladecutscompletelythroughtheworkpiecewhen

rippingorcross-cutting.

2. ALWAYSHOLDWORKFIRMLYagainstthemiter

gaugeorripfence.

3_ USE A PUSH STICK when required. Always use a

push stick when ripping narrow stock. Refer to

ripping instructions in this Operator's Manual where

the push stick is covered in detail. A pattern for

making your own push stick is included on page 23_

4_ NEVER PERFORM ANY OPERATION "FREE

HAND", which means using only your hands to

support or guide the workpiece. Always use either

the fence or the miter gauge to position and guide

the work.

IA DA"GERl

FREEHAND CUTTING JS THE MAJOR CAUSE OF

KICK-BACK & FINGER/HAND AMPUTATIONS.

5. NEVER STAND or have any part of your body in

line with the path of the saw blade. Keep your

hands out of the saw blade path.

6. NEVER REACH behind or over the cutting tool for

any reason.

7. NEVER use a rip fence when cross cutting.

8. DO NOT USE a molding head with this saw.

9. FEED WORK INTO THE BLADE against the

direction of rotation only.

10. NEVER use the rip fence as a cut-off gauge when

cross-cutting.

11. NEVER ATTEMPT TO FREE A STALLED SAW

BLADE without first turning the saw OFF. Turn

power switch OFF and disconnect the plug from the

power source immediately to prevent motor

damage & before removing material

12. PROVIDE ADEQUATE SUPPORT to the rear and

the sides of the saw table for long or wide

workpieces.

l& AVOID KICKBACKS (work thrown back towards

you) by keeping the blade sharp, the rip fence

parallel to the saw blade and by keeping the splitter,

anti-kickback pawls and guards in place and

functioning. Do not release work before it has

passed al! the way past the saw blade and is off the

table. Do not rip work that is twisted, warped or

does not have a straight edge to guide it along the

fence.

14. AVOID AWKWARD OPERATIONS and hand

positions where a sudden slip could cause your

hand to move into the saw blade.

15_ NEVER USE SOLVENTS to clean plastic parts.

Solvents could possibly dissolve or otherwise

damage the material Only a soft damp cloth

should be used to clean plastic parts.

16. MOUNT your table saw on a bench or stand before

performing any cutting operations. Refer to

ASSEMBLY AND ADJUSTMENTS on page 9_

17. NEVER CUT METALS or materials which may

make hazardous dusL

18_ ALWAYS USE tN WELL°VENTILATED AREA.

Remove sawdust frequently. Clean out sawdust

from the interior of the saw to prevent a potential

fire hazard. Attach a vacuum to the dust port for

additional sawdust removal

19_ NEVER LEAVE THE SAW running unattended. Do

not leave the saw until it comes to a complete sto G

20_ FOR proper operation follow the instructions in this

Operator's Manual. Failure to provide sawdust fag

through and removal hole wilt allow sawdust to

build up in the motor area resulting in a fire hazard

and potentia! motor damage (see page 10 for

details).

21_ DO NOT AUTHORIZE ADDITIONAL USERS to

operate this power too! without the accompanying

operators manual for which the user must read and

understan&

22_ THE REAR OF THE TABLE INSERT MUST BE

FLUSH TO THE TABLE during all sawing

operations. A rubber adjusting spacer is provided

under the rear of the insert for this purpose.

23_ DO NOT USE A DADO BLADE LARGER THAN

6 inches in diameter and Y2inch in width. Only

use a stackable dado blade. Do not use adjustable

or wobble dadoes.

24_ NEVER PERFORM A CUTTING OPERATION

USING BOTH the rip fence and the miter gauge at

the same time. This may cause kickback and

serious injury to the operator.

POWERSUPPLYREQUIREMENTS

IAWARNINGn

To avoid electrica! hazards, fire hazards or damage to

the chop saw, use proper circuit protection. Always use

a separate electrical circuit for your tools. This power

too! is wired at the factory for 120V operation. Connect it

to a 120V, 15 Amp circuit and use a 15 Amp time delay

fuse or circuit breaker. To avoid shock or fire, replace

the cord immediately if it is worn, cut or damaged in any

way.

EXTENSION CORD REQUIREMENTS

IAWARNINGn

Any extension cord must be GROUNDED for safe

operation.

MINIMUM GAUGE FOR EXTENSION CORDS

(AWG TYPE /120 VOLT ONLY)

Ampere Rating

More Than Not

More Than

0 6

6 10

10 12

Totai length in feet

25' 50' 100' 150'

18 16 16 14

18 16 14 12

16 16 14 12

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_:_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_:JiH!i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_!_i!_i.iiiiiiiiiiiiiiiiiiiiiiiiiiii_i¸!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_!i!ii¸i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_;!_i_i_i_i_i_i_i_i_i_L_!_i_!_!i_!i!iii_i_i_i_!i_

Any extension cord used for power tools MUST be

grounded (3=wire with two fiat prongs and one round

ground prong)_

Make sure the extension cord is in good condition.

When using an extension cord, make sure you use one

heavy enough to carry the current the tool will draw.

An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. The table

above shows the correct size to use according to

extension cord length and nameplate ampere rating. If

in doubt, use the next heavier gauge cord. The smaller

the gauge number the heavier the cord.

NOTE: The 12 to 16 Amp rating is correct for this tool It

is highlighted in the table above.

Be sure your extension cord is properly wired and in

good condition. Always replace a damaged extension

cord or have it repaired by a qualified person before

using it. Protect your extension cords from sharp

objects, excessive heat and damp or wet areas.

Before connecting the saw to the extension cord, make

sure the saw switch is turned OFR

GROUNDING INSTRUCT_ONS

IN THE EVENT OF A MALFUNCTION OR

BREAKDOWN, grounding provides a path of least

resistance for electric current and reduces the risk of

electric shock. This saw is equipped with an electric

cord that has an equipment grounding conductor and

a grounding plug_ The plug MUST be plugged into

a matching receptacle that is properly installed and

grounded in accordance with ALL local codes and

ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it wil! not

fit the receptacle, have the proper receptacle installed

by a qualified electrician.

_MPROPER CONNECTION of the equipment grounding

conductor can result in risk of electric shock. The

conductor (wire) with the green insulation (with or

without yellow stripes) is the equipment grounding

conductor. If repair or replacement of the electric cord

or plug is necessary, DO NOT connect the equipment

grounding conductor to a live terminal

CHECK with a qualified electrician or service personnel

if you do not completely understand the grounding

instructions, or if you are not sure the saw is properly

grounded.

Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole grounding RECEPTACLES

THAT ACCEPT THE SAW'S PLUG. REPAIR

OR REPLACE DAMAGED OR WORN CORDS

_MMED_ATELY.

3-Prong Plug

Grounding Lug

Adapter

Make Sure This

is Connected to a

Known Ground

2-Prong

Receptacle

RECOMMENDED ACCESSORIES

IAWARN NGn

Visit your Sears Hardware Department or see the

Craftsman Power and Hand Tools Catalog to purchase

recommended accessories for this power tool.

IAWARNINGn

To avoid the risk of personal injury:

o Do not use adjustable (wobble) type dadoes or

carbide tipped dado blades.

o Use only stackable dado blades.

o Maximum dado width is 1/2 in.

® Do not use a dado with a diameter larger than 6 in.

o Do not use molding head set with this saw.

o Do not modify this power too! or use accessories not

recommended by Sears.

TOOLS NEEDED

Medium screwdriver Adjustabie wrench

#2 Phittips screwdriver Combination screwdriver

I Illllllllll 1

Straight edge

13 mm wrench

Separate all parts from packing materials. Check each

part with the illustration on the next page and the "Table

of Loose Parts" to make certain all items are accounted

for, before discarding any packing material

[A WARNING]

If any part is missing or damaged, do not attempt to

assemble the table saw, plug in the power cord, or turn

the switch ON until the missing or damaged part is

obtained and is installed correctly.

TABLE OF LOOSE PARTS

ITEM DESCRIPTION QUANTITY

A. Table saw assembly 1

B_ Blade 1

C. Blade wrenches 2

D. Miter gauge 1

E. 4mm Hex key 1

F_ Guard mounting bolt, flat washer, 1

Toothed washer, oval washer,

Spring washer

G. Blade guard and splitter 1

I. Rip fence, lock handle & nut 1

J. Flat washer & dome nut 1

K. Handwhee! 1

TABLE EXTENS!ON CONTENTS

h Table extension 1

M. Table exL mounting hardware bag 1

N. Table extension rip scale 1

STAND

Short upper support 2

Long upper support 2

Short bottom support bracket 2

Long bottom support bracket 2

Leg 4

Foot Pad 4

Stand mounting hardware bag 1

NOTE: To make assembly easier, keep contents of box

together. Apply a coat of automobile wax to the table.

Wipe al! parts thoroughly with a clean dry cloth. This will

reduce friction when pushing the workpeice. To avoid

injury, the styrofoam block should be removed between

the motor and the table.

UNPACKING YOUR TABLE SAW

G F

° 7

K E C

Miter gauge

Blade guard Table insert Rip fence

Side table

extension

Bevel angle

pointer & scale

Overload reset

switch

ON/OFF switch

with safety key

Bladebevel

Lock knob

Blade elevation & tilting

hanwheel

Front stand

mounting holes Stand

Blade

Anti-kickback pawls

Splitter

Splitter bracket

Rear stand

mounting holes

ASSEMBLESTAND(FIG.A}

1. Unpackallpartsandgroupbytypeandsize.Refer

tothepartslistforcorrectquantities.

2. Attachonelonguppersupport(4)totopofleg(1)

usingonebolt(2)andnut(5).

NOTE:Donottightenboltsuntilstandisproperly

aligned(seestep#8beforetightening).

3. Attachotherendof longuppersupporttotopof

anotherlegusingoneboltandnut.

4. Attachonelongbottomsupport(3)tocenterofeach

legusingbolt(2)andnut(5). Thiscompletesthe

frontframesection.

5. Assemblerearframesectioninexactlythesame

manner.

6. Joinfrontandrearframeassembliesusingtwoshort

uppersupports(11)andtwoshortbottomsupports

(10),boltsandnuts.

7. Insertfootpad(6)intobottomofleg. Repeatfor

eachleg.

8. Placestandonlevelsurfaceandadjustsoal!legs

arecontactingthefloorandareatsimilaranglesto

thefloor.Tightenallbolts.

NOTE:Standshouldnotrockafteral!boltsare

tightened.

Fig.A

ASSEMBLETABLESAWTOSTAND(FIG.A-I)

1. Placeprotectivecardboardoroldblanketonfloorto

protectthesawtablesurface.

2. Placethesawupsidedownontheprotective

material(seeFig.A-I).

3. Positionthestandupsidedownonthesawbase.

NOTE:Makesurefrontofstandandfrontofsaware

facingthesamedirection.

4. Lineupthefourholesinsawbaseandstand.

5. Fastensawtostandusingfourbolts(12),washers

(13)andnuts(14).

NOTE:Placewasheroneachboltbeforeinserting

intosawbaseandthroughthesupport.Nutmustbe

immediatelyagainstthebracket(seeFig.A).

6. Tightenallfournuts.

NOTE:DONOTOVERTIGHTENNUTSHOLDING

SAWTOSTAND.THISMAYDAMAGETHESAW

BASE.

7. Carefullysetthesawinitsuprightpositionona

cleanlevelsurface.

[A WARNING1

tF THE STAND WILL NOT BE USED, DO NOT

OPERATE THE TABLE SAW ON THE FLOOR. THIS

tS A VERY DANGEROUS POSITION.

Fig. A-1

SAWMOUNTEDTOWORKSURFACE(FIG.B)

1. If the leg setwill not be used,the saw mustbe

properlysecuredto a sturdyworkbenchusingthe

fourmountingholesat thebaseofthesaw.

2. Thesurfaceof the table wherethe saw is to be

mountedmusthavea holelargeenoughto facilitate

sawdustfall-throughandremoval.

3. Squarethesawon themountingsurfaceand mark

the!ocationofthefour3/8in. mounting holes (1).

4. Drill 3/8 in. hole into the mounting surface.

5. Mark an 11 in. square (2) centered between the four

mounting holes (1).

6. Cut out and remove the square.

7. This opening will allow sawdust to fal! through the

saw base.

8. Place the saw on the work surface, and align the

mounting holes of the saw with those drilled through

the surface.

9. Fasten the saw to the work surface.

WARNINGn

Do not operate this machine on the floor. This is very

dangerous and may cause serious injury.

Fig. B

IA wARNmNen

Failure to provide the sawdust fall-through hole for use

of the saw when mounted to a worksurface and not a

stand will cause sawdust to build up in the motor area,

which may result in fire or cause motor damage.

ASSEMBLE BLADE RAISING & TILTING WHEEL

(FIG. C}

1. Attach blade raising & tilting hand wheel (1) to the

height regulating bolt (2). Make sure the slot (3) in

the hand wheel hub is engaged with the roll pin (4) in

the height regulating bolt.

2. Fasten hand wheel to height regulating bolt with flat

washer (5) and dome nut (6).

Fig. C

6 5 2

RiP FENCE (FIG. D, E)

1. Thread the rip fence locking handle (2) into the

eccentric (3) of the fence and lock in place by

tightening the nut (1) against the fence head.

Fig. D

23__' I'"--'_ _____--1

KEEPING THE AREA CLEAN

1. Sawdust and wood chips that fai! from under the saw

will accumulate on the floor.

2. Make it a practice to pick up and discard this dust

when you have completed cutting.

2. Liftupwardonripfencehandle(2)sotherearholding

clamp(4)isfullyextended.

3. Placethe ripfenceonthe sawtable(5),engaging

therearfenceclampfirstthenloweringthefrontend

ontothetable.

4. Pushdownonthefencehandle(2)tolock.

Fig.E

2 _ ......

TABLE EXTENSION - RIGHT SIDE (FIG. F)

1. Group like bolts and washers.

2. Thread the three adjusting bolts (1) into the threaded

holes of the extension as shown. Do not thread bolts

beyond the end of the extension.

3. Place a spring washer (3) followed by the flat washer

(5) on bolt (4). Repeat for remaining two mounting

bolts.

4. Position the extension (6) next to the saw table on

the right side (7) and align the mounting holes.

5. Place the bolts and washers into the three holes at

the right side of the saw table as shown.

6. Place a washer (8) and nut (9) on the threaded end

of each bolt, and hand tighten.

7. Lay a straight edge on the saw table and over the

extension (6). Turn the three adjusting screws (1) in

or out accordingly until the extension is flush with the

top of the saw table.

8. Tighten the mounting bolts.

9. Attach the rip scale (10) to the table extension

accordingly.

Fig. F

9 8 5 3 4 10

7 6

INSTALLING AND CHANGING THE BLADE

(FIG. H, t, J)

[_ DANGER]

o To avoid injury from an accidental start, make sure

the switch is in the OFF position and the plug is not

connected to the power source outlet.

® To avoid serious injury, the rear of the table insert

must be level with the table. If the rear of the insert

is not level with the table, adjust the screw (3) in or

out until the rear of the insert is level to or slightly

above the table. To raise the insert, turn the screw

counterclockwise, to lower the insert, turn the screw

clockwise. Note: A rubber adjusting spacer is

provided under rear of insert for this purpose.

1. Remove the table insert (1) by removing the two

screws (2, 3). Be careful not to lose the rubber

spacer that is on the back screw (3) beneath the

table insert (Fig. H).

Fig.H

l 3

2. Raise the blade arbor (4) (Fig. I) to the maximum

height by turning the btade raising handwhee!

counterclockwise.

3. Place the open-end wrench (8) jaws on the flats of

the saw arbor to keep the arbor from turning (Fig. J)

and place the box-end wrench (9) on the arbor nut (5),

and turn counterclockwise.

4. Remove the arbor nut (5) and outer flange (6) (Fig. I).

5_Instal!thesawbladeontothearborwiththe blade

teethpointingtowardthefrontofthesaw.

6_Installtheflange(6)againstthebladeandthreadthe

arbornut(5)asfaraspossiblebyhand.Ensurethat

thebladeis flushagainsttheinnersideof theblade

flange.

IAWARNINGi

To avoid possible injury and damage to the workpiece,

be sure to install the blade with the teeth pointing toward

the front of table in the direction of the rotation arrow on

the blade guard.

Fig. [ 4

7_ To tighten the arbor nut (5) place the open-end

wrench (8) on the flats of the saw arbor to keep the

arbor from turning (Fig. J).

8. Place the box-end wrench (9) on the arbor nut (5),

and turn clockwise (to the rear of the saw table).

9. Replace the blade insert in the table recess, insert

the screws through the front and rear holes and

tighten remembering the rubber washer under the

rear of the insert and leveling the rear of the insert to

the table.

Fig. J

WARNHIG [

To avoid injury from a thrown workpiece, blade parts,

or blade contact, never operate saw without the proper

insert in place. Use the origina! installed insert for all

through sawing operations except dado cuts. A specia!

dado insert plate must be installed when using a dado

blade.

BLADE GUARD ASSEMBLY (FIG. K, L, M)

1. Set the blade to maximum height and the tilt to zero

degrees on the bevel scale with the hand wheels.

Lock the blade bevel lock knob.

2. Place the spring washer (2), flat washer (3), external

tooth lock washer (4) onto the blade guard mounting

bolt (1) (Fig. K).

3. Insert bolt and washer assembly through splitter

bracket (5).

Fig. K

Blade Guard

Splitter

4. Place the oval washer (6) on the pivot rod (7) (Fig. L).

5. Install the blade guard splitter & bracket assembly

into the rear of the saw table. Thread the bolt (1) into

the internally threaded pivot rod until snug.

NOTE: The blade guard & splitter is removed from

the illustration for clarity_

Fig. L

6. Lift blade guard arm (8) up and using a straight edge,

align the blade guard splitter (9) with the saw blade

(10)_

7_ Shift the splitter bracket assembly to right or left unti!

paralle! alignment to the blade is achieved.

8. When the splitter is properly aligned with the saw

blade, tighten the bolt securely.

NOTE: The splitter bracket must always be correctly

aligned so the cut workpiece will pass on either side

without binding or twisting.

[,& DANGER]

Improper splitter alignment can cause "kickback" and

serious injury.

Straight edge

MITER GAUGE ADJUSTMENT (FIG+ N)

1+ To check miter gauge squareness, loosen lock

handle (1) to allow miter body (3) to rotate freely+

Position the miter head so the po+nter (2) points to

90° on the scale+ Tighten lock handle to hold miter

head +n position+ Use a square to verify the 90 °

angle between the miter body and the slide bar+

2+ Hfadjustment is needed, square the miter head to 90°,

loosen the pointer locking screw and adjust pointer

to 90° on the protractor scale then tighten the locking

screw.

3+ To change angles on miter gauge, loosen lock

handle (1) and rotate miter body to desired angle as

indicated by the pointer (2)+ Secure in position by

tightening the lock hand+e+

4+ Jfadjustment is needed to make the fence parallel to

the groove, proceed with the following adjustments:

® Loosen the two bolts (3) and lift up on the handle

(2)+

+ Hold the fence bracket (4) firmly against the front

of the saw table+ Move the far end of the fence

until it is parallel with the m+tergauge groove.

+ Push the handle to lock, then tighten both bolts+

5+ if fence is loose when the handle is in the locked

(downward) position, proceed with the following

adjustment:

+ Lift the handle (2) upward and turn the adjusting

screw (5) clockwise until the bottom of the rear

clamp is 1/16 in+away from the rear of the table+

NOTE: Over-tightening the adjusting screw will cause

the fence to come out of alignment+

[a,WARN+NG]

Fai+ureto proper+y a++gnfence can cause "kickback"

and serious +njury+

NOTE: The rip fence and blade are aligned parallel to

the miter gauge groove of the table.

1 3

Fig. 0

Fig. N

8 6 7

RiP FENCE ADJUSTMENT (FIG. O)

1. The fence (1) is moved by lifting up on the locking

handle (2) and sliding the fence to the desired

!ocation+ Pushing down on the handle locks the fence

in position+

2+ Position the fence on the table and along one edge

of the miter gauge grooves.

3+ Lock the fence hand+e+The fence should be parallel

with the miter gauge groove+

RIP FENCE iNDiCATOR ADJUSTMENT (FIG+ O)

1+ The rip fence indicator (6) points to the rip scale (8)+

The scale references the distance between the fence

and the blade+

2+ Measure the actual distance with a rule+ if there

is a difference between the measurement and the

indicator, adjust the indicator (6)+

3. Loosen the screw (7) and slide the indicator to the

correct measurement on the scale. Tighten the screw

and re-measure+

BLADETtLTJNGMECHANISM

Thesawbladecanbetiltedtwodifferentways.

RAPIDBLADETtLTING(FIG.P)

1. Loosenbladebevellockknob(2).

2. Slidetheentirehandwheelassembly(1)to desired

!ocation_

3. Tightenlockingknob(2). Ensurelockingknobisfully

tightenedbeforeattemptinga cuL

MICRO-ADJUSTMENTBLADETILTING(FIG.P)

1. Loosenbladebevellockknob(2).

2. Pushhandwheel(1) IN to engagethe handwhee!

gearswiththesegmentgearonthetablesawbase.

3. WhileholdinghandwheelIN,turnthehandwheelto

tiltthebladeto thedesiredangle.

4. Tightenlockknobtosecurebevelangle.

NOTE: Changingthe bladeangle can be done

independentlyofchangingbladeheight.

I_WARNINGn

BLADE BEVEL LOCK KNOB (1) MUST BE FIRMLY

TIGHTENED AND LOCKED DURING ALL CUTTING

OPERATIONS.

Fig. P

1 2

BLADE PARALLEL TO THE MITER GAUGE

GROOVE (FIG. Q, R)

This adjustment was made at the factory, but it should

be rechecked and adjusted if necessary.

WARNING]

o To prevent personal injury:

Always disconnect plug from the power source when

o making any adjustments.

This adjustment must be correct or kickback could

result in a serious injury and accurate cuts can not be

made.

1. Remove the safety switch key and unplug the saw.

2. Remove the blade guard for this procedure but

reinstalI and realign after adjustment.

3. Raise the blade to the highest position and set at the

0° angle (90 ° straight up).

4_ Select and mark, with a felt tip maker, a blade tooth

having a "right set" and rotate the blade so the

marked tooth is 1/2in. above the table at the front of

the saw.

5. Place the combination square base (1) into the right

side miter gauge groove (2).

6. Adjust the rule so it touches the front marked tooth

and lock ruler so it holds its position in the square

assembly.

7_ Rotate the blade bringing the marked tooth to the

rear and about 1/2in. above the table.

8_ Carefully slide the combination square to the rear

until the ruler touches the marked tooth.

9_ If the ruler touches the marked tooth at the front

and rear position indicating the same measurement,

no adjustment is needed at this time. If not perform

adjustment procedure described in next section.

Fig. Q

BLADE HEIGHT ADJUSTMENT (FIG. P)

To raise the saw blade, turn handwheel (1)

COUNTERCLOCKWISE To lower the blade, turn the

handwheel CLOCKWISE.

It is not necessary to loosen blade tilting locking knob (2)

when raising or lowering the saw blade.

ADDiTiONALBLADEADJUSTMENTS(FIG.R)

TOOLSREQUIRED

o 10mmopenendor10ramcombinationwrench

® 4ramhexkey

o Framingsquare

o Mediumsizeflatbladescrewdriver

ADJUSTMENTPROCEDURE

1. Turn saw switch OFF and remove plug from the

power source.

2. Remove blade guard and splitter assembly, miter

gauge and rip fence.

3. Using the 10ram hex wrench, slightly loosen the two

middle blade alignment rod strap bolts (1) and two-

rear blade alignment rod strap bolts (2) located on

the underside of the saw table (see Fig. R).

4. While standing at the rear of the saw, use a medium

size flat blade screwdriver and gently pry the rear

of the blade alignment rod to the LEFT or RIGHT.

Using the framing square, simultaneously measure

the distance at the front and rear of the blade to an

edge of a miter slot. When the distances are within

1/64" or closer, tighten both rear blade alignment rod

strap bolts (2) while holding the rod firmly in place.

NOTE: The blade alignment rod will only move

slightly.

5. If alignment is not achieved by rear adjustment,

loosen the two front blade alignment rod strap bolts

(3).

6_ While standing at the front of the saw, use a medium

size flat blade screw driver and gently pry the front

of the blade alignment rod to the RIGHT or LEFT.

Simultaneously measure the distance at the front and

rear of the blade to an edge of a miter slot. When

the distances are with in 1/64" or closer, tighten both

front blade alignment rod strap bolts (3) while holding

the rod firmly in place. NOTE: The blade alignment

rod will only move slightly to the righL

7. Tighten both middle blade alignment rod strap bolts

(1). NOTE: Re-check to make sure all six bolts are

properly tightened and that the distance from the

front and rear of the blade to the miter gauge groove

are within 1/64th of an inch from one another.

8_ Re-install blade guard and splitter assembly and

adjust the alignment with the blade as outlined earlier

in the operator's manual.

0° BEVEL STOP (FIG. S)

1. Raise the blade to maximum height by rotating the

handwheel counterclockwise.

2. Loosen bevel angle lock knob.

3. Tilt the blade to 0° bevel.

4. Using a square (1), verify blade is 90 ° to the table

top.

5. If blade is not 90° to the table, back off the

adjustment screw (2)

6. Loosen bevel lock knob and square blade 90° to the

table.

7. Once blade is at 90° to the table top, lock bevel angle

locking knob.

8. Carefully tighten adjusting screw (2) until it touches

the beve! stop. DO NOT OVER TIGHTEN.

9_ Recheck to ensure blade is stilI aligned at 90%

Fig. S

BEVELPOINTERADJUSTMENT(FIG.T)

Whenyouhaveachieveda 90° angleofthebladeto

thetabletopasdescribedinsectionabove,theangle

pointermayrequireadjustment.Ifso,followproceeding

steps:

1. Loosenpointerscrew(2)andmovethepointersoit

isalignedwith0° onthebevelscale.

2. Retightenthepointerscrew.

45° BEVELSTOP(FIG.U}

1_Raisethebladeto maximumheightbyrotatingthe

handwheelcounterclockwise.

2_Loosenbevelanglelockknob.

3_Tiltthebladeto45° bevel

4_Usinga square(1),verifybladeis45°to thetable

top.

5_Ifbladeisnot45° tothetable,backoffthe

adjustmentscrew(2).

6_Loosenbevellockknobandsquareblade45°tothe

table.

7_Oncebladeisat45°to thetabletop,lockbevelangle

lockingknob.

8_Carefullytightenadjustingscrew(2)untilittouches

thebevelstop. DONOTOVERTIGHTEN.

9_Recheckto ensurebladeisstil!alignedat 45°_

Fig.U

8ASmC SAW OPERATmONS

ON/OFF SWITCH (FIG. V)

The on/off switch (2) is located on the front panel of the

saw base. To turn the saw ON, move the switch to the

up position. To turn the saw OFF, move the switch to

the down position.

LOCKING SWITCH tN "OFF" PosmoN (FIG. V)

When the saw is not in use, the switch should be locked

in the OFF position. To lock the switch in the OFF

position, pull out the safety key (1) from the center of

the switch. The saw will not start with the key removed.

However, if the key is removed while the switch is in

the ON position, it can be turned off ONCE. The saw

wil! not restart until the key has been reinserted into the

switch and the switch is turned on.

OVERLOAD PROTECTION (FIG. V)

This saw is equipped with a thermal overload reset

switch, if the motor shuts off or fails to start due to

overloading or low voltage, turn the switch to OFF

position and let the motor coo! down and remove aft

cutting materials from the saw. After the motor has

cooled down, push the reset button (3) to reset the

overload device. The saw should now start when the

switch is returned to the ON position.

To avoid injury, the ON/OFF switch should be in the OFF

position and the pJug removed from the power source

while the motor cool down takes place. This will prevent

accidental starting when the reset button is pushed.

Overheating may be caused by misaligned parts, a dul!

blade, or an undersized extention cord. inspect the saw

for proper setup before using it again.

Fig. V

RESET

CUTTING OPERATIONS

There are two basic types of cuts: ripping and

crosscutting. Ripping is cutting along the length and with

the grain of the workpiece. Crosscutting is cutting either

across the width or across the grain of the workpiece.

Neither ripping nor crosscutting may be done safely

freehan& Ripping requires the use of the rip fence, and

crosscutting requires the miter gauge. Never use a rip

fence and miter gauge at the same time.

[A WARNING]

Before using the saw each and every time, check the

following:

1. Blade is tight on the arbor.

2. Bevelanglelockknob is tight.

3. If ripping, fence lock handle is tight and fence is

parallel to the blade.

4. Blade guard is in place and working properly.

5. Safety glasses are being worn.

The failure to adhere to these common safety rules, and

those printed within this manual, can greatly increase

the likelihood of injury.

RIPPING (FIG W, X)

WARNING ]

® Do not ai!ow familiarity or frequent use of your table

saw to cause careless mistakes. Remember that

even a careless fraction of a second is enough to

cause a severe injury.

® Keep both hands away from the blade and path of

the blade.

o The workpiece must have a straight edge against the

fence and must not be warped, twisted, or bowed.

IA DANGERI

Never attempt to pull the workpiece backwards

during a cutting operation. This wil! cause kickback

and serious injury to the user can occur.

1. Remove the miter gauge. Secure the rip fence to the

table at the desired rip measurement.

2. Raise the blade so it is about 1/8" higher than the top

of the workpiece.

3. Place the workpiece flat on the table and against the

fence. Keep the workpiece about 1" away from the

blade.

4. Turn the saw ON and wait for the blade to come up

to speed.

5. Slowly feed the workpiece into the blade by pushing

forward only on the workpiece section (1) that will

pass between the blade and the fence (Fig. W).

IAWARNINGn

AVOID KICKBACK by pushing forward that section of

the workpiece that wil! pass between the blade and the

fence. Use a push stick at all times.

Fig. W

RIPPING SMALL PIECES

[_ WARNING]

Avoid injury from the blade contact. Never make

through-saw cuts narrower than 3/4 in. wide.

1. it is unsafe to rip small pieces. Instead, rip a larger

piece to obtain the size of the desired piece.

2. When a sina!! width is to be ripped, your hand cannot

be safely put between the blade and the rip fence,

therefore, use one or more push sticks to pass the

workpiece completely through and past the blade.

6_ Keep your thumbs off the table top. When your hand

reaches the front edge of the table (2), finish the cut

with a push stick (3) (Fig. X). You can make a push

stick using the pattern on page 23.

7_ The push stick (3) should always be used during al!

ripping operations_

8. Continue pushing the workpiece with the push stick

(3) until it passes the blade guard and clears the rear

of the table.

DANGER]

Never attempt to pull the workpiece backwards during

a cutting operation. This will cause kickback and

serious injury to the user can occur. When the blade

completely stops raise the anti-kickback pawls on

each side of the splitter and slide the workpiece out.

Fig. X

REVEL RIPPING

This cut is the same as ripping except the blade bevel

angle is set to an angle other than "0".

WARNINGI

Cut only with the workpiece and the fence on the right

side of the blade.

IA DANGERI

Never attempt to pui! the workpiece backwards during a

cutting operation. This wfl! cause kickback and serious

injury to the user can occur.

CROSSCUTTING 90° MITER ANGLE (FIG. Y)

[,_ WARNING ]

To prevent serious injury:

o Do not allow familiarity or frequent use of your table

saw to cause careless mistakes. Remember that

even a careless fraction of a second is enough to

cause a severe injury.

o Keep both hands away from the blade and the path

of the blade.

® Never attempt to pull the workpiece backwards

during a cutting operation. This will cause kickback

and serious injury to the user can occur.

1. Remove the rip fence and place the miter gauge a

miter gauge groove on the table.

2. Adjust the blade height so it is 1/8 in. higher than the

top of the workpiece.

3. Hold the workpJece firmly against the miter gauge

with the blade path in line with the desired cut

location. Move the workpiece to one inch distance

from the blade.

4. Start the saw and wait for the blade (1 to come up

to full speed. Never stand directly inline of the saw

blade path, always stand to the side of the blade that

you are cutting on.

5. Keep the workpiece (2) against the face of the miter

gauge (3) and fiat against the table. Then slowly

push the workpiece through the blade.

6. Do not try to pull the workpiece back with the blade

turning. Turn the switch OFF, and carefully slide the

workpiece out when the blade is completely stopped.

[A WARNING]

Always position the larger surface of the workpiece on

the table when crosscutting and/or bevel crosscutting to

avoid unstabiiity.

Fig,Y

BEVELCROSSCUTTING(FIG.AA)

0°~45° BLADEBEVEL&90° MITER ANGLE

This cutting operation is the same as crosscutting

except the blade is at bevel angle other than 0%

MAWARNING

Always work to the right side of the blade during this

type of cut. The miter gauge must be in the right side

groove because the bevel angle may cause the blade

guard to interfere with the cut if used on the left side

groove.

1. Adjust the blade (1) to the desired angle, and tighten

the blade bevel lock knob.

2. Tighten miter lock handle (3) at 90°.

3. Hold workpiece firmly against the face of the miter

gauge throughout the cutting operation.

Fig. AA

COMPOUND MITER CROSSCUTTING (FIG. BB}

00~45 ° BLADE BEVEL & 00~45° rvIITER ANGLE

This sawing operation is combining a miter angle with a

bevelangle_

[,_ WARNING ]

Always work to the right side of the blade during this

type of cut. The miter gauge must be in the right side

groove because the bevel angle may cause the blade

guard to interfere with the cut if used on the left side

groove.

1. Set the miter gauge (3) to the desired angle.

2. Place the miter gauge in the right side groove of

the table_

3. Set the blade (1) bevel to the desired bevel angle

and tighten the blade bevel lock knob.

4. Hold workpiece firmly against the face of the miter

gauge throughout the cutting operation.

Fig. BB

1 3

MITERING (FIG. CO) 00~45° MITER ANGLE

This sawing operation is the same as crosscutting

except the miter gauge is locked at an angle other

than 90°.

1. Set the blade (1) to 0° bevel angle and tighten the

blade bevel lock knob.

2. Set the miter gauge (3) at the desired miter angle

and lock in position by tightening the miter gauge

lockinghandle_

3. Hold theworkpiece(2)firmlyagainstthefaceofthe

mitergauge throughoutthecuttingoperation.

FIG. CC

3 2 1

USING WOOD FACING ON THE RiP FENCE (FIG. DD)

When performing some special cutting operations,

You can add a wood facing (1) to either side of the rip

fence (2).

1. Use a smooth straight 3/4 in. thick wood board (1)

that is as long as the rip fence.

2. Attach the wood facing to the fence with wood

screws (3) through the holes in the fence. A wood

fence should be used when ripping material such

as thin paneling to prevent the material from

catching between the bottom of the fence and the

table.

Fig. DD 3

IAWARN Nen

ABRASIVE AND METAL CUTTING BLADES MUST

NOT BE USED WITH THiS SAW

This saw was not made to cut metals or masonry

materials. Doing so may result in injury, it will also void

the warranty.

IAWARNINGn

ALL BLADES MUST:

1. Be rated at 5000 RPM or higher.

2. Have a 5/8 in. arbor hole.

3. Be no larger in diameter than 10 in.

Smaller diameter blades may be used. While this wil!

result in a reduced depth of cut, the output of the motor

will be increased.

DADO CUTS (FIG. EE)

[,_k WARNING ]

a. Only Stsckeble dsdo blades can be used on this

sew.

b. DO NOT use Adjustable or Wobble type dadoes.

c. Maximum dado cut width is 1/2in.

1. A dado table insert must be purchased separately for

this saw to accept a dado blade. Remove saw blade

and blade guard for dado cuts ONLY. Reinstall and

realign blade guard for all through sawing operations.

Instal! a dado not exceeding 6 in_in diameter and 1/2

in. in width

2. Instal! the dado table insert making sure the rear of

the insert is flush with the table. A rubber adjusting

spacer is provided under the rear of the insert for this

purpose.

3. instruction for operating the dado is packed with the

separately purchased dado set.

4. The arbor (1) on this saw restricts the maximum

width of the cut to Y2in.

5. It is not necessary to install the outside flange (2)

before threading on the arbour nut (3) for maximum

1/2in. dado cuts. Make sure that the arbor nut (3) is

tight, and that at least one thread of the arbor sticks

out past the nut.

6. Use only the correct number of round outside blades

and inside chippers as shown in the dado set's

instruction manual. Blade/chippers must not exceed

1/2in. total in width.

7. Check saw to ensure that the dado will not strike the

housing, insert, or motor when in operation.

[,&WARNING]

For your own safety, always replace the blade, blade

guard assembly, and blade insert when you are

finished with the dado operation. You must also realign

the blade guard assembly.

Fig. EE

GENERAL MAINTENANCE

IAWAR" "Gn

For your own safety, turn the switch OFF and remove

the switch key. Remove the plug from the power source

outlet before maintaining or lubricating your saw.

1. Clean out al! sawdust that has accumulated inside

the saw cabinet and the motor.

2. Polish the saw table with an automotive wax to keep

it clean and to make it easier to slide the workpiece.

3. Clean cutting blades with pitch and gum remover.

4. A worn, cut, or damaged power cord should be

replaced immediately.

IA WARNINGn

All electrical or mechanical repairs should be attempted

only by a trained repair technician. Contact the nearest

Sears Service Center for service. Use only identical

replacement parts. Any other parts may create a hazard.

5. Use liquid dish washing detergent and water to clean

al! plastic parts. NOTE: Certain cleaning chemicals

can damage plastic parts.

6. Avoid use of the following cleaning chemicals or

solvents; ammonia and household detergents

containing ammonia.

BLADE RAISING AND TmLTmNGMECHANISM

After each five full hours of operation, the blade raising

mechanism and tilting mechanism should be checked

for looseness, binding, or other abnormalities. With the

saw disconnected from the power source, turn the saw

upside down and alternately pull upward and downward

on the motor unit. Observe any movement of the motor

mounting mechanism. Looseness or play in the blade

raising screw (1) (Fig. FF) should be adjusted as follows:

1. Using a 14mm wrench, loosen the check-nut (2).

2. Adjust nut (3) until it is finger-tight against the bracket

(4), then back off the nut (3) 1/6 turn.

3. Tighten nut (2) with the wrench, while holding nut (3)

in place. Maximum allowable play in and out of the

screw rod (1) is 1/8 in.

Fig. FF

You can place a small amount of dry lubricant on bevel

andgle adjustment rod also. This rod (1) must be

kept clean and free of sawdust, gum, pitch, and other

contaminants for smooth operation.

If excessive looseness is observed in any parts of the

blade raising mechanism or tilting mechanism, take the

complete unit to a Sears Service Center.

LUBRICATmON

All motor bearings are permanently lubricated at the

factory and require no additional lubrication.

On all mechanical parts of your table saw where a pivot

or threaded rod are present, lubricate using graphite or

silicone. These dry lubricants will not hold sawdust as

would oil or grease.

la,WARNINGU

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before

making any adjustments.

o Consult your local Sears Service Center if for any reason the motor will not run.

SYMPTOM

Saw wil! not start

Does not make accurate

45 °and 90°rip cuts

Material pinched blade

when ripping

Material binds on splitter

Saw makes unsatisfactory

cuts

Material kicked back from 1.

blade 2.

Blade does not raise or tilt 1.

freely

Blade does not come up to 1.

speed 2.

Machine vibrates

excessively

Does not make accurate

45 °and 90°cross cuts

POSSIBLE CAUSES CORRECTIVE ACTION

1. Saw not plugged in 1. Plug in saw

2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker

3. Cord damaged 3. Have cord replaced by a Sears

Service Center

1. Positive stop not adjusted correctly 1. Check blade with square and adjust

2. Bevel angle pointer not set accurately positive stop

2. Check blade with square and adjust

to zero

1. Rip fence not aligned with blade 1. Check and align rip fence

2. Warped wood, edge against fence is 2. Select another piece of wood

not straight

1. Splitter not aligned correctly with blade 1. Check and align splitter with blade

1. Duli blade 1.

2. Blade mounted backwards 2.

3. Gum or pitch on blade 3.

4. Incorrect blade for work being done

5. Gum or pitch on blade causing erratic 4.

feed 5.

Rip fence out of adjustment 1.

Splitter not aligned with blade 2.

Feeding stock without rip fence 3.

Dul! blade 4.

Operator is letting go of material before 5.

it is past saw blade

Miter anqle lock handle is not tiqht 6.

Sawdust and dirt in raising and tilting 1.

mechanisms

Extension cord too light or too long 1.

Low house voltage 2.

1. Saw not mounted securely to

workbench

2. Stand not level

3. Damaged saw blade

1. Miter gauge out of adjustment

Replace blade

Blade teeth must face forward

Remove blade and clean with

turpentine and coarse steel wool

Change the blade

Clean table with turpentine and steel

wool

Align rip fence with miter gauge slot

Align splitter with blade

install and use rip fence

Replace Blade

Push material all the way past saw

blade before releasing work

Tiqhten handle

Brush or blow out loose dust and

dirt

Replace with adequate size cord

Contact your electric company

1. Tighten al! mounting hardware

2. Adjust stand level to floor

3. Replace blade

1. Square miter gauge to 90°

PUSH STICK CONSTRUCTION

® This is aPdli°sizedrawing (actual size)

*Use good quatity plywood or solid wood

o Use ½° or %" material

® Push stick MUST be thinner than the

width of matedal being cut

10 raN°TABLE SAW PARTS UST MODEL NO. 137.2t8010

Ia'WARNINGn

When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause

product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless

repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center.

LD. NO, Description Size QTY

09JK WRENCH

0AV8 BODY SHELL

0AW8 SEGMENT GEAR

0B1M WHEEL

0B21 HEIGHT REGULATING BOLT

0B23 SADDLE

0B24 SPRING

0B25 POINTER BRACKET

0B29 NEEDLE POINTER #23

0B2C SWITCH BOX

0B2N TABLE #53

0B3R WRENCH

0B3W RETAINING CLIP

0B48 WARNING LABEL

0B84 WASHER

0B99 SPACER

0B9C PLUNGER HOUSING

0B9G ANGLE ROD

0B9M STRAP 6

0B9W BRACKET

0B9Z COMPRESSION SPRING

0BA1 COMPRESSION SPRING

0BA4 SPACER

0BAC SET NUT

0BAE ARBOR COLLAR

0BAJ BLADE

0BBU EXTENTION WING #06

0BPA LOCK KNOB

0BQF TABLE EXT M(X NTING HARDWARE BAG

0G1 U DUST SHIELD 4

0J3P HEX. WRENCH 4 mm 1

0J4F FLAT WASHER @8X16-2.5 1

0J4H FLAT WASHER @1@30-0.2 2

0J70 FLAT WASHER 1/4_ 3/4-7/64 1

0J72 FLAT WASHER 1/4"5/8-1/16 1

0J76 FLAT WASHER 1/4_3/4-1/16 5

0J7F FLAT WASHER 5/16_7/8-5/64 1

0J7K FLAT WASHER 3/8_ 29/32-5/64 1

0J7N FLAT WASHER 3/8_ 11/16-1/16 6

0J7V FLAT WASHER 5/8"1 3/8-5/64 1

0J8D FLAT WASHER 3/8_ 3/4-5/64 2

0J95 SPRING WASHER @6 1

0J9H SPRING WASHER @1/4" 6

0J9K SPRING WASHER @3/8 3

0JAA WASHER @8 1

0JAE EXTERNAL TOOTH LOCK WASHER @4 2

0JC9 SPRING PiN 1

0JE7 C-RING 1

0JPD HEX. HD, BOLT M6_1.0-16 3

i.D. NO. Description Size

0JST HEX, HD, BOLT "3/8_ 16UNC-1

0JXL HEX, SOC. SET SCREW M10_1.5-12

0JYN HEX. SOC. COUNTERSUNK HD. SCREW M6_1.0-25

0KOZ HEX, HD, SCREW AND WASHER M8"1.25-16

0K16 HEX, HD, SCREW AND WASHER M8_1.25-16

0K25 HEX,SOCKET HD.CAP SCREWS M5_0.8-20

0K3G CR,RE. PAN HD. SCREW & WASHER M5_0.8-12

0K3R CR,RE. PAN HD. SCREW & WASHER MSX0.8-12

0K5P CR, RE, COUNT HD, SCREW M6_1.0-50

0KSC CR, RE,COUNT HD. TAPPING SCREW M4_l 8-10

0K91 CR, RE, TRUSS HD. TAPPING SCREW M4_16-12

0KA4 CR, RE, PAN HD. TAPPING SCREW M4_16-16

0KCX CR, RE, PAN HD PLAIN WASHER TAPPING SCREW M5"0.8-10

0KEK CR, RE, PAN HD. SCREW M6_1.0-30

0KEM CR, RE, PAN HD. SCREW M6_1.0-40

0KF7 CR RE, PAN HD. SCREW M4_0.7-12

0K J4 CAP HD, SQ.NECK BOLT M6_1.0-35

0K J5 CAP HD, SQ.NECK BOLT M6X1,0-80

0KMR HEX, NUT M5_0.8 T=4

0KMS HEX, NUT M6_1.0 T=5

0KMV HEX, NUT M10_1,5 T=8

0KMW HEX, NUT M10"1 5 T=4

0KMY HEX. Ix,UT M8_1.25 T=6.5

0KP2 HEX, NUT 3/8"16UNC T=8

0KQJ CROWN NUT M8_ 1.25 T=12.5

0KRQ SERRATED TOOTHED HEXAGON FLANGE NUT MM1.0 T=6

0KRX HEXAGON NUT AND FLAT WASHER M6"1.0

0KSW STRAIN RELIEF @6,1

0KTA STRAIN RELIEF

0L65 POWER CABLE ASS'Y

0LSL CIRCUIT BREAKER SWITCH

0LW5 ROCKER SWITCH

0QEL MOTOR

0QQ0 CLAMP-CORD

0SGC HANDLE BAR

20WQ HEX. HD, BOLT M6_1.0-50

21BN BRACKET GROUP ASS'Y

27QV DEFLECTOR

28NF SCALE

28NG SCALE

2919 FLAT WASHER @10"17-2 #06

297F BLADE GUARD ASSY

29R2 WARNING LABEL

2BOL OPERATORS MANUAL

2BJM MITER GAUGE ASS'Y

2BUF RIP FENCE ASS'Y

2BZS LABEL

Z00U iNSERT ASSY #23

QTY

10 raN."FABLE SAW SCHEMATmC MODEL NO. 137.218010

OB2N

0J764

0KRX4

0BBU

0B3W

)SGC

OBAC 0K_Q_

OBAE

10 raN.TABLE SAW PARTS UST & SCHEMATmC

STAND

MODEL NO. 137.218010

IoDoNO.

2003

2004

2005

2006

2007

O?3B

OJ4F

OJPP

OKJ7

OKRR

20N0

201T

ZO2W

Descdpfion

LONG BOTTOM SUPPORT BRACKET

SHORT BOTTOM SUPPORT BRACKET

LONG UPPERSUPPORT

SHORT UPPER SUPPORT

BRACKET

FOOT PAD

FLAT WASHER

HEX. HD. BOLT

CAP HD. SO.NECK BOLT

SERRATEDTOOTHED HEXAGON FLANGE NUT

FOOT PAD ASS'Y

STAND ASSEMBLY

STAND HARDWARE BAG ASSEMBLY

Size

L=616mm#o6

L=528.4mm#o6

L=462mm #o6

L=428mm #06

W=46mm.L=58&6mm #o6

#06

@8X16-2.5

M8* 1.25-30

M8'1.25-16

MS* 1.25 T=7.5

QTY

]

20074

\1/

093B4

10 raN.TABLE SAW PARTS UST & SCHEMATmC

MOTOR

MODEL NO. 137.218010

I.D. Size

0HV8 BALL BEARING 1

0HVU BALL BEARING 1

0JAL EXT.TOOTH LOCK WASHER _4 4

OJX3 HEX. SOC. SETSCREW M5"0.8-8 2

OK3A CR.REPANHD. SCREW & WASHER M5"0.8-30 4

OK5V CR.-RE. COUND.HD.SCREW M4xO.7-8 4

0KTH STRAIN RELIEF 1

0QE1 ARBOR SHAFTASS'Y 1

0QEA BRACKET 1

0QED BUPPGRTPLATE 1

0QEH FIELDASS'Y 1

I.D. Descr@_ion Size

0QEJ ARMATUREASS'Y

0QEK MOTOR NAMEPLATE

0QM2 BRUSH HOLDER ASS'Y (i'27"°26.5

0QQT BRUSHASS'Y

0QR0 BRUSH COVER

0R1Q MOTOR HOUSING

0R1S BEARING BUSHING

0R20 BAFFLE

10ZQ NEEDLE BEARING

110A CR.RE. PAN HEAD TAPPING & WASHER SCREW M5"12-55

0QFJ

0IN8

/0R20

0QE1 jlOZQ

._OQRO 2

.OR1Q

0_32

Your Home

For repair - in your home - of aft major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

Operator's Manuals that you need to do-it-yourself.

For Sears professional installation of home appfiances

and items like garage door openers and water heaters.

(1-800-469o4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, cal! or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488o 1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparaci6n

a domicflio, y para ordenar piezas:

1o888-SU-HOGAR _M

(1-888-784-6427)

Au Canada pour service en frangais:

lo800-LE-FOYER "°

(1-800-533-6937)

www.sears.oa

® Registered Trademark /TM Trademark /SM Service Mark of Sears, Roebuck and Co.

® Marca Registrada /TM Marca de Fb.brica /SM Mama de Ser,vicio de Sears, Roebuck and Co.

MC Marque de commerce /MD Marque d6pos6e de Sears, Roebuck and Co. @ Sears, Roebuck and Co.

2005.04. REV1

Craftsman 137218010 User Manual TABLE SAW Manuals And Guides L0511162

CRAFTSMAN Saw Table Manual L0511162 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation