Craftsman 137218100 User Manual TABLE SAW Manuals And Guides L0606544
CRAFTSMAN Saw Table Manual L0606544 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides
User Manual: Craftsman 137218100 137218100 CRAFTSMAN TABLE SAW - Manuals and Guides View the owners manual for your CRAFTSMAN TABLE SAW #137218100. Home:Tool Parts:Craftsman Parts:Craftsman TABLE SAW Manual
Open the PDF directly: View PDF 
.
Page Count: 28
Operator's Manual
CRFIFrXMFIN°
3.0 HP (Max. Developed)
10" Inch Blade
5000 R.P.M.
TABLE SAW
Model No.
137.218100
137.248100 /with Stand
TABLE SAW
CAUTION:
Before using this Table Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
• Safety Instructions
•Installation
•Operation
•Maintenance
•Parts List
•Espahol
Customer Help Line
1-800-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www.sears.com/craftsman
Part No. 13721810001
SECTION PAGE
Warranty ........................................ 2
Product Specifications ....................... 2
Power Tool Safety ............................ 3
Table Saw Safety .............................. 4
Electrical Requirements and Safety ...... 5
Accessories and Attachments .............. 6
Tools Needed For Assembly ................ 6
Carton Contents .............................. 6
SECTION PAGE
Know Your Table Saw ....................... 8
Assembly and Adjustments ................. 9
Operation ....................................... 15
Maintenance ................................... 19
Troubleshooting Guide ....................... 20
Push Stick Plan ................................. 21
Parts List......................................... 22
FULL ONE YEAR WARRANTY
If this Table Saw fails due to a defect in material or workmanship within one year of date of purchase,
Sears will at its option repair or replace it free of charge.
Return this Table Saw to a Sears Service Center for repair, or to place of purchase for replacement.
This warranty gives you specific legal rights, and you may also have other rights which may vary from
state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
= Lead from lead-based paints
= Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment such as dust
masks that are specially designed to filter out microscopic particles.
MOTOR
HP(Maximum developed) ...... 3.0
Type .................................. Universal
Amps ................................. 15
Voltage .............................. 120
Hz ...................................... 60
RPM (no load) ...................... 5000
Overload Protection ............. YES
SAW
Table Size ........................ 26-7/64" x 19-3/32"
Table Extensions ............... Yes, with fences
Extension Fence Capacity... 24" Right
Blade Size ........................ 10"
Rip Scale ......................... YES
Rip Fence ........................ YES
Miter Gauge ...................... YES
Maximum Cut Depth @ 90°.. 3"
Maximum Cut Depth @ 45°.. 2-1/2"
Maximum Dado Cut Width... 1/2"
Net Weight, 21810 ............. 44 LBS
Net Weight, 24810 ............. 51 LBS
To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.
This table saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt /15 Ampere
time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or
damaged in any way.
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these
rules could result in serious injury to you or damage to the table saw.
Before using your table saw, it is critical that you read and understand these safety rules.
Failure to follow these rules could result in serious injury or damage to the table saw.
Good safety practices are a combination of common
sense, staying alert and understanding how to use your
power tool. To avoid mistakes that could cause serious
injury, do not plug in your power tool until you have read
and understood the following safety rules:
1. READ and become familiar with this entire
Operator's Manual. LEARN the tool's applications,
limitations and possible hazards.
2. Look for this symbol that identifies important safety
precautions. It means CAUTION!
BECOME ALERT! YOUR SAFETY IS INVOLVED!
15.
16.
17.
18.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning ON.
NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER "OFF". Do not leave the tool
before it comes to a complete stop.
NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
DO NOT OVERREACH. Keep proper footing and
balance at all times.
,
,
.
6.
NEVER OPERATE THIS MACHINE WITHOUT THE
SAFETY GUARD IN PLACE FOR ALL THROUGH-
SAWING OPERATIONS.
DO NOT USE IN ADANGEROUS ENVIRONMENT
such as damp or wet locations or exposure to rain.
Keep work area well lighted.
DO NOT use power tools in the presence of
flammable liquids or gases.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
19.
20.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for most efficient and safest performance.
Follow instructions for lubricating and changing
accessories.
CHECK FOR DAMAGED PARTS. Before further
use of the tool, a guard or other part that is damaged
should be carefully checked to ensure it will operate
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, mounting and any other conditions that may
affect its safe operation. A guard or other part that is
damaged should be properly repaired or replaced.
7. KEEP CHILDREN AWAY. All visitors should be kept
at a safe distance from the work area. 21. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
8. DO NOT FORCE THE TOOL. It will do the job
better and safer at the rate for which it was designed.
g. USE THE RIGHT TOOL. Don't force the tool or
attachment to do a job for which it is not designed.
10. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry which may get caught in moving parts. Non-
slip footwear is recommended. Wear protective hair
covering to contain long hair.
11. WEAR A FACE MASK OR DUST MASK. Sawing,
cutting and sanding operations produce dust.
12. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, cutters, etc.
13. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure the switch is in the OFF
position before plugging into the power supply.
14. USE ONLY RECOMMENDED ACCESSORIES.
Consult the Operator's Manual for recommended
accessories. The use of improper accessories may
cause injury to you or damage to the tool.
22.
23.
24.
25.
DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could impair your ability to use the tool safely.
USE DUST COLLECTION SYSTEM wherever
possible. Dust generated from certain materials can
be hazardous to your health and in some cases, a
fire hazard. Always operate the power tool in a well-
ventilated area with adequate dust removal.
ALWAYS WEAR EYE PROTECTION. Any power
tool can throw foreign objects into your eyes which
could cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with ANSI
safety standard Z87.1. Everyday glasses have only
impact resistant lenses. They ARE NOT safety
glasses.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could cause serious injury when they
break.
DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.
.ALWAYS USE SAW BLADE GUARD, splitter and 12.
anti-kickback pawls for every operation for which they
can be used, including through-sawing Through-
sawing operations are those in which the blade cuts 13.
completely through the workpiece when ripping or
cross-cutting.
2. ALWAYS HOLD WORK FIRMLY against the miter
gauge or rip fence.
.USE A PUSH STICK when required. Always use a
push stick when ripping narrow stock. Refer to
ripping instructions in this Operator's Manual where
the push stick is covered in detail. A pattern for
making your own push stick is included on page 27.
.NEVER PERFORM ANY OPERATION "FREE
HAND", which means using only your hands to
support or guide the workpiece. Always use either the
fence or the miter gauge to position and guide the
work.
WARNING: FREEHAND CUTTING IS THE MAJOR
CAUSE OF KICK-BACK & FINGER/HAND
AMPUTATIONS.
5. NEVER STAND or have any part of your body in line
with the path of the saw blade. Keep your hands out
of the saw blade path.
6. NEVER REACH behind or over the cutting tool for
any reason.
7. REMOVE the rip fence when cross cutting.
8. DO NOT USE a molding head with this saw.
g. FEED WORK INTO THE BLADE against the
direction of rotation only.
10. NEVER use the rip fence as a cut-off gauge when
cross-cutting.
11. NEVER ATTEMPT TO FREE A STALLED SAW
BLADE without first turning the saw OFF. Turn
power switch OFF immediately to prevent motor
damage.
14.
15.
16.
17.
18.
19.
20.
PROVIDE ADEQUATE SUPPORT to the rear and
the sides of the saw table for long or wide workpieces.
AVOID KICKBACKS (work thrown back towards you)
by keeping the blade sharp, the rip fence parallel to
the saw blade and by keeping the splitter, anti-
kickback pawls and guards in place and functioning.
Do not release work before it has passed all the way
past the saw blade. Do not rip work that is twisted,
warped or does not have astraight edge to guide it
along the fence.
AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause your hand
to move into the saw blade.
NEVER USE SOLVENTS to clean plastic parts.
Solvents could possibly dissolve or otherwise
damage the material. Only a soft damp cloth should
be used to clean plastic parts,
MOUNT your table saw on a bench or stand before
performing any cutting operations. Refer to
ASSEMBLY AND ADJUSTMENTS on page 9.
NEVER CUT METALS or materials which may make
hazardous dust.
ALWAYS USE IN WELL-VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust from
the interior of the saw to prevent a potential fire
hazard. Attach a vacuum to the dust port for
additional sawdust removal.
NEVER LEAVE THE SAW running unattended. Do
not leave the saw until it comes to a complete stop.
FOR proper operation follow the instructions in this
Operator's Manual entitled ASSEMBLY AND
ADJUSTMENTS (Page 9). Failure to provide
sawdust fall-through and removal hole will allow
sawdust to build up in the motor area resulting in a
fire hazard and potential motor damage.
POWER SUPPLY REQUIREMENTS
To avoid electrical hazards, fire hazards or damage to
the table saw, use proper circuit protection. Always
use a separate electrical circuit for your tools. This
power tool is wired at the factory for 120V operation.
Connect it to a 120V, 15 Amp circuit and use a 15
Amp time delay fuse or circuit breaker. To avoid
shock or fire, replace the cord immediately if it is
worn, cut or damaged in any way.
EXTENSION CORD REQUIREMENTS
IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provides a path of least
resistance for electric current and reduces the risk of
electric shock. This saw is equipped with an electric cord
that has an equipment grounding conductor and a
grounding plug. The plug MUST be plugged into a
matching receptacle that is properly installed and
grounded in accordance with ALL local codes and
ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit
the receptacle, have the proper receptacle installed by a
qualified electrician.
Any extension cord must be GROUNDED for safe
operation.
MINIMUM GAUGE FOR EXTENSION CORDS
(AWG type /120 Volt only)
Ampere Rating
Not
More Than More Than
0 6
6 10
10 12
Total length in feet
25' 50' 100' 150'
18 16 16 14
18 16 14 12
16 16 14 12
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor (wire) with the green insulation (with or without
yellow stripes) is the equipment grounding conductor. If
repair or replacement of the electric cord or plug is
necessary, DO NOT connect the equipment grounding
conductor to a live terminal.
CHECK with a qualified electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the saw is properly
grounded.
GUIDELINES FOR EXTENSION CORDS
Any extension cord used for power tools MUST be
grounded (3 wire with two flat prongs and one round
ground prong).
USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE
3-PRONG GROUNDING PLUGS AND 3-POLE
GROUNDING RECEPTACLES THAT ACCEPT THE
SAW'S PLUG. REPAIR OR REPLACE DAMAGED OR
WORN CORDS IMMEDIATELY.
Make sure the extension cord is in good condition. When
using an extension cord, make sure you use one heavy
enough to carry the current the tool will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table above shows
the correct size to use according to extension cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge cord. The smaller the gauge number the
heavier the cord.
NOTE: THE 12 TO 16 AMP RATING IS CORRECT FOR
THIS TOOL. IT IS HIGHLIGHTED IN THE TABLE
ABOVE.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Before connecting the saw to the extension cord, make
sure the saw switch is turned OFF.
GROUNDING INSTRUCTIONS
3-Prong Plug
®
Prong
_-'" Properly Grounded
3-Prong Receptacle
Grounding Lug _:-_'_---_
_Make Sure This
is Connected to a
Known Ground
"" 2-Prong
Receptacle
RECOMMENDED ACCESSORIES UNPACKING AND CHECKING CONTENTS
Visit your Sears Hardware Department or see the
Craftsman Power and Hand Tools Catalog to purchase
recommended accessories for this power tool.
Separate all parts from packing materials. Check each part
with the illustration on the next page and the "Table of
Loose Parts" to make certain all items are accounted for,
before ny packing material.
To avoid the risk of personal injury:
• Do not use adjustable (wobble) type dadoes or carbide
tipped dado blades, maximum dado width is 1/2".
• Do not use a dado with a diameter larger than 6".
• Do not use molding head set with this saw.
• Do not modify this power tool or use accessories not
recommended by Sears.
TOOLS NEEDED
Medium serewd_{vet
#2 Phillips screwdriver
Straight edge
Adjustable wrench
Combination square
If any part is missing or damaged, do not attempt to
assemble the table saw, plug in the power cord, or turn the
switch ON until the missing or damaged part is obtained
and is installed correctly.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION QUANTITY
A. Table saw assembly 1
B. Blade guard and splitter 1
C. Bolt, flat washer, toothed washer, 1 each
Oval washer, spring washer
D. Rip fence handle & nut 1
E. Hand wheels 2
F. Dome nuts 2
G. Hand wheel handle 2
H. Dado table insert 1
I. Miter gauge 1
J. Hex keys 2
K. Blade wrenches 2
L. Table extension fence 1
M. Locking Knobs 2
N. Blade 1
NOTE: To make assembly easier, keep contents of box
together. Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean dry cloth. This will
reduce friction when pushing the workpeice.
UNPACKING "tOUR TABLE SAW:
!
_L
AN
C
GH
|
M
Rip Fence Blade Guard
Table Insert
Miter Gauge
Table SideTable
Extension
Extension
handles
Blade bevel
lock knob
with key
Overload reset
switch
Mounting holes
Blade Tilting
Handwheel
Blade elevation
handwheel
Blade
Kickback pawls
i
Splitter bracket
_ghole
SAW MOUNTED TO WORK SURFACE (FIG. A)
1. If the leg set will not be used, the saw must be
properly secured to a sturdy workbench using the
four mounting holes at the base of the saw.
2. The surface of the table where the saw is to be
mounted must have a hole large enough to facilitate
sawdust fall-through and removal.
3. Square the saw on the mounting surface and mark
the location of the four 3/8" mounting holes (1).
4. Drill 3/8" hole into the mounting surface.
5. Mark an 11" square (2) centered between the four
mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to fall through the
saw base.
8. Place the saw on the work surface, and align the
mounting holes of the saw with those drilled through
the surface.
9. Fasten the saw to the work surface.
Do not operate this machine o the floor-this is a very
dangerious position.
Fig. A
Fig. B
BLADE RAISING HANDWHEEL (FIG. C)
1. Attach the handwheel (t) to the elevation screw (2)
at the front of the saw.
Make sure the slots (3) in the hub of the
handwheel engage with the pins (4).
2. Attach and tighten the dome nut (5) at the end of
the shaft (Fig. D).
Fig. C
O
O
O
--2
3
1
2 4
Failure to provide the sawdust fall-through hole will
cause sawdust to build up in the motor area, which
may result in fire or cause motor damage.
KEEPING THE AREA CLEAN (FIG. B)
1. Sawdust and wood chips that fall from under the
saw will accumulate on the floor.
2. Make it a practice to pick up and discard this dust
when you have completed cutting.
Always keep your work area clean, uncluttered and
well lit. Do not work on floor surfaces that are
slippery from sawdust or wax.
BLADE TILTING HANDWHEEL (FIG. D)
1. Attach the other handwheel (6) to the blade tilting
screw on the side of the saw in the same manner
as above.
2. Attach and tighten the handwheel dome nut (5).
Fig. D
RIP FENCE (FIG. E)
1. Thread the fence handle (1) into the cam hole (2)
until tight.
2. Lift upward on the rip fence handle (t) so that the
holding clamp (3) is fully extended.
3. Place the rip fence on the saw table and engage
the holding clamp (3) to the table rear. Lower the
front end onto the front rail (4).
4. Push down on the fence handle (1) to lock.
Fig. E
1 Iit
INSTALLING AND CHANGING THE BLADE
(FIG. F, G, H)
I_WARNINGI
• To avoid injury from an accidental start, make
sure the switch is in the OFF position and the
plug is not connected to the power source outlet.
• To avoid serious injury, table insert must be level
with the table. If the table insert is not level with
the table, adjust the screw (3) until it is level with
the table. To raise the insert, turn the screw
counterclockwise, to lower the insert, turn the
screw clockwise.
1. Remove the table insert (1) by unscrewing the two
screws (2, 3). Be careful not to lose the rubber
washer that is on the back screw (3) beneath the
table insert. (Fig. F)
Fig. F
lit , 2
2. Raise the blade arbor (4) (Fig. G) to the maximum
height by turning the blade raising handwheel
counterclockwise.
3. Remove the arbor nut (5) and flange (6), remove
blade.
4. Install the saw blade onto the arbor with the blade
teeth pointing toward the front of the saw.
5. Install the flange (6) against the blade and thread
the arbor nut (5) as far as possible by hand. Ensure
that the blade is flush against the inner side of the
blade flange.
WARNINGI
To avoidpossibleinjuryand damage totheworkpiece
be suretoinstallthebladewiththeteethpointing
towardthefrontoftableinthedirectionoftherotation
arrowon thebladeguard.
Fig. G
5
6. To tighten the arbor nut (5) place the open-end
wrench jaws on the flats of the saw arbor to keep
the arbor from turning. (Fig. H)
7. Place the box-end wrench (8) on the arbor nut (5),
and turn clockwise (to the rear of the saw table).
8. Replace the blade insert in the table recess, insert
the screws through the front and rear holes and
tighten.
Fig. H
7
IAk WARNING
8
To avoid injury from a thrown workpiece, blade parts,
or blade contact, never operate saw without the proper
insert in place. Use the saw blade insert when sawing.
Use the dado head insert when using a dado.
10
BLADEGUARDASSEMBLY(FIG.I,J, K)
1.Setthebladetomaximumheightand the tilt to
zero degrees on the bevel scale with the hand
wheels. Lock the blade lock knob.
2. Place the external toothed lock washer (1), a steel
flat washer (2) and a spring washer (10) onto the
long hex head bolt (3). Insert the bolt into the
splitter bracket (4) as shown. (Fig. I)
Fig. I
1
lo 3
3. Place the oval washer (5) on the pivot rod (6).
(Fig. J)
4. Install the bracket assembly (4) into the rear of the
saw table. Thread the bolt (3) into the internally
threaded pivot rod.
NOTE: The splitter is removed from the illustration
for clarity.
Fig. J
5. Position the blade guard arm (7) to the rear of the
table. (Fig. K)
6. Using a straight edge, check to see the blade
guard splitter (8) is aligned with the saw blade (9).
7. If straightening adjustment is necessary, loosen
the bolt (3) and shift the splitter assembly to right
or left, or rotate.
8. When the splitter is properly aligned with the saw
blade, tighten the bolt.
9. If height adjustment is necessary, loosen the knob
(11 ) and raise the splitter assembly to the desired
height and tighten the knob. (Fig. I)
NOTE: The splitter must always be correctly
aligned so that the cut workpiece will pass on
either side without binding or twisting to the side.
1!
Improper splitter alignment can cause "kickback" and
Serious injury.
Fig. K
7
anti-kickback pawl
3•
INSTALLING THE TABLE EXTENSION FENCE
(FIG. L, M)
NOTE:
A. For ripping 10" ~ 14" workpiece, the extension
fence has to be installed in the IN-RIP position
(Fig. L). Raise the fence to a position that just
clears the table surface and secure in place
using lock handles (1) for IN-RIP position.
B. For ripping 14" ~ 24" workpiece, the extension
fence has to be installed in the OUT-RIP position
(Fig. M).
1. Install the locking handle (1) on the aluminum
extension table.
2. Place the table extension fence (2) on the
aluminum extension table.
3. Raise the fence to the desired height and tighten
the lock handle (1).
Fig. L ___.j
Fig. M
ADJUSTMENT INSTRUCTIONS
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source, before making any
adjustments.
ADJUSTING THE TABLE EXTENSION (FIG. N)
NOTE: The table extension may be installed on the right
side of the table, as needed, to support long workpiece.
To adjust the table extension position
1. Loosen the two clamp bolts (4) on the two extension
tube brackets.
2. Slide the extension tubes in or out until the scale on
the front tube is positioned at the desired distance.
Tighten the two clamp bolts.
3. To adjust fence position, loosen lock handles (5) and
position auxiliary fence (6).
4. Tighten lock handles (5).
MITER GAUGE ADJUSTMENT (FIG. O)
1. Make sure that the miter gauge will slide freely
through both table grooves.
2. Loosen the lock knob (1). Set the pointer (2) to the
90° mark on the scale.
3. Make a 90° cut in a piece of scrap wood. Check cut
piece to see if it was cut at 90 °. If it is not, continue
to adjust the miter gauge body (3) until the wood
piece is cut at 90°. Refer to OPERATION section for
cutting instructions.
Fig. 0
RIP FENCE ADJUSTMENT (FIG. P)
1. The fence (1) is moved by lifting up on the handle (2)
and sliding the fence to the desired location. Pushing
down on the handle locks the fence in position.
2. Position the fence on the right side of the table, and
along one edge of the miter gauge grooves.
3. Lock the fence handle. The fence should be parallel
with the miter gauge groove.
4. If adjustment is needed to make the fence parallel to
the groove, do the following:
• Loosen the two screws (3) and lift up on the handle
(2).
• Hold the fence bracket (4) firmly against the front of
the saw table. Move the far end of the fence until it
is parallel with the miter gauge groove.
• Tighten both screws and push the handle to lock.
5. If fence is loose when the handle is in the locked
(downward) position, do the following:
• Move the handle (2) upward and turn the adjusting
screw (5) clockwise until the rear clamp is snug. Do
not turn the adjusting screw more than 1/4 turn at a
time.
Over-tightening the adjusting screw will cause the fence
to come out of alignment.
2--
Failure to properly align fence can cause "kickback"
and serious injury.
Fig. P
RIP FENCE INDICATOR ADJUSTMENT (FIG. P)
1. The rip fence indicator (6) points to the measurement
scale (8). The scale shows the distance from the side
of the fence to nearest side of the blade.
2. Measure the actual distance with a rule. If there is a
difference between the measurement and the
indicator, adjust the indicator (6).
Loosen the screw (7) and slide the indicator to the
correct measurement on the scale. Tighten the screw
and re-measure with the rule.
]2
To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.
ADJUSTING THE 90°AND 45° POSITIVE STOPS
(FIG.Q, Q-l, R)
Your saw has positive stops that will quickly position the
saw blade at 90° to the table. Make adjustments only if
necessary.
90° Stop
1. Disconnect the saw from the power source.
2. Turn the blade elevation handwheel and raise the
blade to the maximum elevation.
3. Loosen the blade bevel lock handle (2) and move the
blade to the maximum vertical position. Tighten the
lock handle (2).
4. Place a combination square on the table and against
the blade (1) to determine if the blade is 90° to the
table. (Fig. Q-l)
5. If the blade is not 90° to the table, loosen the two set
screws (4), located on the bottom of the table saw,
(Fig. R) with the hex key, and back off the collar..
6. Loosen the bevel lock knob. Turn the blade tilting
handwheel to move the blade until it is 90° to the
table.
7. Adjust the collar (5) so it contacts the bracket (3)
when the blade is 90 ° to the table. Tighten the two set
screws (4).
45° Stop
1.
Fig. Q-1
90° 45 °
1
With the blade in the upright 90° position, loosen the
bevel lock knob and move the blade to the 45°
position as far as it will go.
2. Place the combination square on the table as shown
in (Fig.Q-I) to check if the blade is 45° to the table.
3. If the blade is not 45° to the table, adjust the screw (4)
(Fig. R) with a screw driver until the blade is 45 ° to the
table.
4. Tighten the bevel lock handle.
5. Tighten the screw (4) until resistance is felt. Do not
overtighten.
BLADE TILT POINTER
1. When the blade is positioned at 90°, adjust the blade
tilt pointer to read 0° on the scale.
2. Loosen the holding screw, position pointer over 0° and
tighten the screw.
NOTE: Make a trial cut on scrap wood before making
critical cuts. Measure for exactness.
Fig. R __
345
BLADE PARALLEL TO THE MITER GAUGE GROOVE
(FIG. R, S)
This adjustment was made at the factory, but it should be
rechecked and ac usted if necessary.
To prevent personal injury:
•Always disconnect plug from the power source when
making any adjustments.
• This adjustment must be correct or kickback could
result in a serious injury and accurate cuts can not
be made.
1. Remove the yellow switch key and unplug the saw.
2. Move the blade guard out of the way.
3. Raise the blade to the highest position and set at the 0°
angle (90° straight up).
4. Select and mark, with a felt tip maker, a blade tooth
having a "right set".
5. Place the combination square base (1) into the right
side miter gauge groove (2). (Fig. Q-l)
6. Adjust the rule so it touches the front marked tooth and
lock ruler so it holds its position in the square assembly.
7. Rotate the blade bringing the marked tooth to the rear
and about 1/2 inch above the blade.
8. Carefully slide the combination square to the rear until
the ruler touches the marked tooth.
9. If the ruler touches the marked tooth at the front and
rear position, no adjustment is needed at this time. If
not, perform adjustment procedure described in next
section.
Fig. S
13
Additional blade adjustments (Fig. T)
1. If the front and rear measurements are not the same,
remove the combination square and loosen the four
adjusting screws (1) on the top of the table about a half
turn.
2. With a folded piece of cardboard covering the blade to
protect your hands, move the blade carefully to the left
or right as much as needed to align the blade correctly.
3. Tighten the four screws (1) and re-measure, as
described in steps 4 to 9 in the prior section.
4. If sufficient adjustment cannot be made by the four
adjusting screws (t), then also loosen the two adjusting
screws (2). Loosen these screws only if necessary.
5. Recheck blade clearance making sure that the blade
does not hit the table insert or other parts when at the
90° and 45° settings.
6. Tighten all screws.
Fig. T
14
BASIC SAW OPERATIONS
RAISE THE BLADE (FIG. U)
To raise or lower the blade, turn the blade elevation
handwheel (1) to the desired blade height, and then
tighten lock handle (2) to maintain the desired blade
angle.
Fig. U
3
TILTING THE BLADE (FIG. U)
1. To tilt the saw blade for bevel cutting, loosen the
lock knob (2) and turn the tilting handwheel (3).
2. Tighten the lock knobs (2) to secure.
ON/OFF SWITCH (FIG. V)
The ON /OFF switch has a removal key. With the
key removed from the switch, unauthorized and
hazardous use by children and others is minimized.
1. To turn the saw ON, insert key (1) into the slot in
the switch (2). Move the switch upward to the ON
position.
2. To turn the saw OFF, move the switch downward.
3. To lock the switch in the OFF position, grasp the
end (or yellow part) of the toggle switch (1), and
pull it out.
4. With the switch key removed, the switch will not
operate.
5. If the switch key is removed while the saw is running,
it can be turned OFF but cannot be restarted
without inserting the switch key (1).
Fig. V
OVERLOAD PROTECTION (FIG. V)
This saw has a reset overload relay button (3) that
will restart the motor after it shuts off due to
overloading or low voltage. If the motor stops during
operation, turn the ON /OFF switch to the OFF
position. Wait about five minutes for the motor to
cool. Push in on the reset button (3) and turn the
To avoid injury, the ON /OFF switch should be in the
OFF position and the plug removed from the power
source while the cool down takes place, to prevent
accidental starting when the reset button is pushed.
Overheating may be caused by misaligned parts or a
dull blade. Inspect your saw for proper setup before
using it again.
USING THE TABLE EXTENSION (FIG. W)
NOTE: Raise the fence to a position that just clears
the table surface and secure in place using lock
handles for IN-RIP position.
1. Remove the stop screws from the ends of the
tubes.
2. Slide the ends of the tubes through both support
brackets on the side your workpiece will be
needing support, and replace the two stop screws.
3. Rotate the front tube to display the scale as an
extenson of the table top scale.
4. Slide the extension out until the correct
measurement is displayed on the tube scale.
5. Loosen the fence handles, and raise or lower the
fence as needed.
6. Tighten all extension support handles and knobs.
Fig. W
15
CUTTINGOPERATIONS
Therearetwobasictypesofcuts:rippingand
crosscutting.Rippingiscuttingalongthelengthandthe
grainoftheworkpiece.Crosscuttingiscuttingeither
across the width or across the grain of the workpiece.
Neither ripping nor crosscutting may be done safely
freehand. Ripping requires the use of the rip fence, and
crosscutting requires the miter gauge.
AVOID KICKBACK by pushing forward that section of
the workpiece that will pass between the blade and the
fence.
Fig. X
Before using the saw each and every time, check
the following:
1. Blade is tight on the arbor.
2. Bevel angle lock knob is tight.
3. If ripping, fence knob is tight and fence is
parallel to the miter gauge grooves.
4. Blade guard is in place and working properly.
5. Safety glasses are being worn.
The failure to adhere to these common safety rules,
and those printed in the front of this manual, can
greatly increase the likelihood of injury.
RIPPING(FIG. W, X)
To prevent serious injury:
• Never use the miter gauge when ripping.
• Never use more than one rip fence during a single cut.
• Do not allow familiarity or frequent use of your table
saw to cause careless mistakes. Remember that even
a careless fraction of a second is enough to cause a
severe injury.
• Keep both hands away from the blade and path of the
blade.
• The workpiece must have a straight edge against
the fence and must not be warped, twisted, or
bowed.
1. Remove the miter gauge. Secure the rip fence to the
table.
2. Raise the blade so it is about 1/8" higher than the top
of the workpiece.
3. Place the workpiece flat on the table and against
the fence. Keep the workpiece about 1" away from
the blade.
4. Turn the saw ON and wait for the blade to come up to
speed.
5. Slowly feed the workpiece into the blade by
pushing forward only on the workpiece section (1)
that will pass between the blade and the fence.
(Fig. X)
6. Keep your thumbs off the blade top. When both of your
thumbs touch the front edge of the table (2), finish the
cut with a push stick. Make a push stick using the
pattern on page 2t.
7. The push stick (3) should always be used when the
ripped workpiece is 2" or narrower (1). (Fig. Y)
8. Continue pushing the workpiece with the push stick
(3) until it passes the blade guard and clears the
rear of the table.
9. Never pull the piece back when the blade is turning.
Turn the switch OFF. When the blade completely
stops raise the anti-kickback pawls on each side of
the splitter and slide the workpiece out.
Fig. Y
3
2
1
ld
BEVELRIPPING
Thiscutisthesameasrippedexcept the blade bevel
angle is set to an angle other than "0".
Cut only with the workpiece and the fence on the right
side of the blade.
RIPPING SMALL PIECES
Avoid injury from the blade contact. Never make
through-saw cuts narrower than 1/2" wide.
1. It is unsafe to rip small pieces. Instead, rip a larger
piece to obtain the size of the desired piece.
2. When a small width is to be ripped and your hand
cannot be safely put between the blade and the rip
fence, use one or more push sticks to move the
workpiece.
Fig. Z
CROSSCUTTING (FIG. Z)
To prevent serious injury:
•Do not allow familiarity or frequent use of your table
saw to cause careless mistakes. Remember that even
a careless fraction of a second is enough to cause a
severe injury.
• Keep both hands away from the blade and the path of
the blade.
1. Remove the rip fence and place the miter gauge in
the left side groove.
2. Adjust the blade height so it is 1/8" higher than the top
of the workpiece.
3. Hold the workpiece firmly against the miter gauge with
the blade path in line with the desired cut location.
Move the workpiece to one inch distance from the
blade.
4. Start the saw and wait for the blade (t) to come up to full
speed.
5. Keep the workpiece (2) against the face of the miter
gauge (3) and flat against the face of the gauge and flat
against the table. Then slowly push the workpiece through
the blade. (Fig. Y)
6. Do not try to pull the workpiece back with the blade
turning. Turn the switch OFF, and carefully slide the
workpiece out when the blade is completely stopped.
BEVEL CROSSCUTTING (FIG. AA)
This cutting operation is the same as crosscutting
except the blade is at bevel angle other than 0°.
1. Adjust the blade (1) to the desired angle, and
tighten the blade bevel lock knob.
2. Always work to the left side of the blade. The miter
gauge (3) must be in the left side groove (2). It
cannot be used in the right side groove unless the
miter angle is very sharp, as it will interfere with the
blade guard.
Fig. AA
f
2
17
COMPOUNDMITER CROSSCUTTING (FIG. BB)
This sawing operation is combining amiter angle with a
bevel angle.
1. Set the miter gauge (3) to the desired angle. Use
only the left side groove (2).
2. Set the blade (1) bevel to the desired angle.
3. Carefully push the miter gauge to begin the
cutting operation.
Fig. BB
3 2 1
MITERING (FIG. CC)
This sawing operation is the same as crosscutting
except the miter gauge is locked at an angle other
than 90°.
1. Hold the workpiece (2) firmly against the miter
gauge (3).
2. Feed the workpiece slowly into the blade (t) to
prevent the workpiece from moving.
Fig. CC
USING WOOD FACING ON THE RIP FENCE
(FIG. DO)
When performing some special cutting operations,
add a wood facing (1) to either side of the rip
fence (2).
NOTE: Before using wood facing on the rip fence,
make sure the auxiliary fence is removed.
1. Use a smooth straight 3/4" thick wood board (1) that is
as long as the rip fence.
2. Attach the wood facing to the fence with wood
screw (3) through the hole in the fence. A wood
fence should be used when ripping material such
as thin paneling to prevent the material from
catching between the bottom of the fence and the
table.
Fig. DD
DADO CUTS (FIG. EE)
1. The dado table insert is included with this saw.
Remove saw blade, blade guard, installed dado, and
dado table insert.
2. Instruction for operating the dado is packed with the
separately purchased dado set.
3. The arbor (1) on this saw restricts the maximum width
of the cut to 1/2".
4. It is not necessary to install the outside flange (2)
before screwing on the arbor nut (3). Make sure that
the arbor nut (3) is tight, and that at least one thread
of the arbor sticks out past the nut.
5. Use only the 6" dado set and keep the width 1/2" or
less. It will be necessary to remove the blade guard
and splitter when using adado blade. Always use
caution when operating a dado blade.
6. Use only the correct number of round outside blades
and inside chippers as shown in the dado set's
instruction manual. Blade or chipper must not exceed
1/2".
7. Check saw to ensure that the dado will not strike
the housing, insert, or motor when in operation.
18
For your own safety, always replace the blade, blade
guard assembly, and blade insert when you are finished
with the dado operation.
Fig. EE
i
ii
i
J
"3
MAINTAINING YOUR TABLE SAW
GENERAL MAINTENANCE
Fig. FF
For your own safety, turn the switch OFF and remove
the switch key. Remove the plug from the power source
outlet before maintaining or lubricating your saw.
1. Clean out all sawdust that has accumulated inside the
saw cabinet and the motor.
2. Polish the saw table with an automotive wax to keep
it clean and to make it easier to slide the workpiece.
3. Clean cutting blades with pitch and gum remover.
4. A worn, cut, or damaged power cord should be
replaced immediately.
All electrical or mechanical repairs should be attempted
only by a trained repair technician. Contact the nearest
Sears Service Center for service. Use only identical
replacement parts. Any other parts may create a hazard.
5. Use liquid dish washing detergent and water to clean
all plastic parts.
NOTE: Certain cleaning chemicals can damage
plastic parts.
6. Avoid use of the following cleaning chemicals or
solvents, ammonia and household detergents
containing ammonia.
BLADE RAISING AND TILTING MECHANISM
After each five hours of operation, the blade raising
mechanism and tilting mechanism should be checked
for looseness, binding, or other abnormalities. With the
saw disconnected from the power source, turn the saw
upside down and alternately pull upward and downward
on the motor unit. Observe any movement of the motor
mounting mechanism. Looseness or play in the blade
raising screw (1) (Fig. FF) should be adjusted as follows:
1. Using a wrench, loosen nut (2).
2. Adjust nut (3) until it is finger-tight against the
bracket (4), then back off the nut (3) 1/6 turn.
3. Tighten nut (2) with the wrench, while holding nut (3)
in place. Maximum allowable play of screw rod (1)is
4 mm.
Place a small amount of dry lubricant on bevel gear (2).
Screw rod (1) must be kept clean and free of sawdust, gum,
pitch, and other contaminants for smooth operation.
If excessive looseness is observed in any parts of the
blade raising mechanism or tilting mechanism, take the
complete unit to a Sears Service Center.
LUBRICATION
All motor bearings are permanently lubricated at the
factory and require no additional lubrication.
On all mechanical parts of your table saw where a pivot or
threaded rod are present, lubricate using graphite or
silicone. These dry lubricants will not hold sawdust as
would oil or grease.
19
Toavoidinjuryfromanaccidentalstart,turntheswitchOFFandalwaysremovetheplugfromthepowersource
beforemakinganyadjustments.
• ConsultyourlocalSearsServiceCenterifforanyreasonthemotorwillnotrun.
SYMPTOM POSSIBLECAUSES CORRECTIVEACTION
Sawwillnotstart 1.Sawnotpluggedin 1.Pluginsaw
2.Fuseblownorcircuitbreakertripped 2.Replacefuseorresetcircuitbreaker
3.Corddamaged 3.Havecordreplacedby a SearsService
Center
Doesnotmakeaccurate45° 1.Positivestopnotadjustedcorrectly 1.Check blade with squareand adjust
and90° ripcuts positivestop
2.Tiltangle pointer not set accurately 2. Check blade with square and adjust to
zero
Material pinched blade when 1. Rip fence not aligned with blade 1. Check and adjust rip fence
ripping 2. Warped wood, edge against fence is 2. Select another piece of wood
not straight
Material binds on splitter 1. Splitter not aligned correctly with 1. Check and align splitter with blade
blade
Saw makes unsatisfactory
cuts
Material kicked back from
blade
Blade does not raise or tilt
freely
Blade does not come up to
speed
Machine vibrates excessively
Does not make accurate 45°
and 90° cross cuts
1. Dull blade 1.
2. Blade mounted backwards 2.
3. Gum or pitch on blade 3.
4. Incorrect blade for work being done 4.
5.Gum or pitch on blade causing erratic 5.
feed
1. Rip fence out of adjustment 1.
2. Splitter not aligned with blade 2.
3. Feeding stock without rip fence 3.
4. Splitter not in place 4.
5. Dull blade 5.
6. The operator letting go of material 6.
before it is past saw blade
7. Miter angle lock knob is not tight 7.
1. Sawdust and dirt in raising and tilting
mechanisms
1. Extension cord too light or too long
2. Low house voltage
1. Saw not mounted securely to
workbench
2. Bench on uneven floor 2.
3. Damaged saw blade 3.
1. Miter gauge out of adjustment 1.
Replace blade
Turn the blade around
Remove blade and clean with turpentine
and coarse steel wool
Change the blade
Clean table with turpentine and steel wool
Align rip fence with miter gauge slot
Align splitter with blade
Install and use rip fence
Install and use splitter (with guard)
Replace blade
Push material all the way past saw blade
before releasing work
Tighten knob
1, Brush or blow out loose dust and dirt
1. Replace with adequate size cord
2. Contact your electric company
1. Tighten all mounting hardware
Reposition on flat level surface Fasten to
floor if necessary
Replace blade
Adjust miter gauge
2O
bo
Cut off here to
push 1/4" wood.
Cut off here to
1/2" woo&
m
i
1/2" Squares.
i
r
i
Notch to help
t prevent hand
from slipping.
J i
t
ti
J
i
i
PUSHSTICK
-- Make from 1/2' or 3/4" __-_-.....
wood or thickness
Jessthan width of _ ._. ___
material to be cut.
CAUTION!
Use only good
strong wood _
or plywood,
Use a jigsaw or _
bandsaw to
cut out.
Optional
hanging hole, \
I
10" TABLE SAW PARTS LIST
WARNING I
MODEL NO. 137.218100/137.248100
When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause
product damage.
WARNINGI
Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a
qualified service technician. Repair service is available at your nearest Sears Service Center.
Always order by I.D.NO.
Schematic A
I.D. NO, DESCRIPTION SIZE
0806 KNOB
2008 EXTENTION WING
2009 TABLE
0B3B SCALE
0B3H INSERT
0B57 PARALLEL BRACKET ASS'Y
0B6S CLAMP HANDLE
0B7Y GUARD BRACKET
0B84 WASHER
0B8A WARNING STICK LABEL (ONLY FOR 137.218100)
0BCD GUIDE HOLDER
0BCH ASSIST-FENCE
0BCL SIDE COVER
0BCT SCALE
0BEF WARNING LABEL
0H8H CLAMP BOLT
0J4E FLAT WASHER _#6X13-1
0J76 FLAT WASHER 114X314-1116
0J78 FLAT WASHER 114Xll2-3132
0J95 SPRING WASHER _#6
0JAA WASHER _/,8
0JAE EXTERNAL TOOTH LOCK WASHER (#4
0JYN HEX. SOC. COUNTERSUNK HD. SCREW M6X1.0-25
0K3R CR.RE. PAN HD. SCREW & WASHER M5X0.8-12
0K5P CR. RE. COUNT HD. SCREW M6X1.0-50
0K8E CR. RE.COUNT HD. TAPPING SCREW M5X16-12
0KDR CR. RE. PAN HD. SCREW M5X0.8-10
0KDS CR. RE. PAN HD. SCREW M5X0.8-40
0KF6 CR. RE. PAN HD. SCREW M4X0.7-8
0KJ2 CAP HD. SQ.NECK BOLT M6X1.0-25
0KKW CR.RE. PAN HD. ROUND NECK SCREW M6X1.0-16
0KMS HEX. NUT M6X1.0 T=5
0KMS HEX. NUT M6X1.0 T=5
0KMY HEX. NUT M8X1.25, T=6.5
0KSW STRAIN RELIEF
0WEV KNOB
202N BLADE GUARD ASS'Y
202R UPER TUBE
202S UPER TUBE
20L1 SLOTTED PAN HD.SCREW M6X1.0-25
20LW CR.RE. PAN HD. SCREW & WASHER M5X0.8-16
20WQ HEX. HD. BOLT M6X1.0-50
212M LEAD WIRE ASS'Y
22KU WARNING LABEL
25MG MITER GAUGE ASS'Y
QTY
2
1
1
1
1
1
1
1
1
1
3
1
2
1
1
2
1
1
1
1
1
1
6
2
3
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
6
1
1
1
1
22
J
21eM
J \ \
\
Q_B
\\
)
/
/
W
-_. r-
m
0
C3
m
r-
Z
0
(.3
"-4
ko
=_
oo
_=_
=_
"-4
ko
4_
O0
10" TABLE SAW PARTS LIST MODEL NO. 137.218100/137.248100
Schematic B
I.D. NO. DESCRIPTION SIZE QTY I.D. NO. DESCRIPTION SIZE QTY
09JK WRENCH HEX 1 0JCR SPRING PIN 8-90 1
0AV9 BODY SHELL 1 0JE7 C-R_NG 1
0B1N WHEEL I 0JED C-R_NG 1
0B22 HEIGHT REGULATING BOLT 1 0JEY E-R_NG 1
0B23 SADDLE 1 0JXL HEX. SOC. SET SCREW M10X1.5-12 1
0B24 SPRING 1 0KOZ HEX. HD. SCREWAND WASHER M8X1.25-16 4
0B25 POINTER BRACKET 1 0K16 HEX. HD. SCREW AND WASHER M8X1.25-16 1
0B2A NEEDLE POINTER I 0K25 HEX.SOCKET HD.CAP SCREWS M5X0.8-20 I
0B2C SWITCH BOX 1 0K3G CRRE. PAN HD. SCREW & WASHER M5X0.8-12 1
0B3K INSERT t 0K7K CR RE. ROUND WASHER HD SCREW M6X1.0-12 2
0B3R WRENCH I 0K8C CR RE.COUNT HD TAPPING SCREW M4X18-10 4
0B3V PLATE COVER 1 0K91 CR RE. TRUSS HD. TAPPING SCREW M4XI6-12 4
0B3Y RETAINING CLIP I 0KA4 CR.RE. PAN HD. TAPPING SCREW M4X16-16 2
0B48 WARNING LABEL 1 0KDU CR RE. PAN HD. SCREW M6XI.0-12 2
0B97 MOTOR BRACKET 1 0KF7 CR RE. PAN HD. SCREW M4X0.7-12 2
0B99 SPACER I 0K J0 CAP HD. SQ.NECK BOLT M6XI.0-16 2
0B9C PLUNGER HOUSING 1 0K J4 CAP HD. SQ.NECK BOLT M6XI.0-35 1
0B9H ANGLE ROD I 0K J5 CAP HD. SQ.NECK BOLT M6XI.0-80 I
0B9M STRAP 6 0KM1 RIVET _s_5-11 3
0B9S BRACKET t 0KMR HEX. NUT M5X0.8 T=4 t
0B9W BRACKET I 0KMS HEX. NUT M6X1.0 T=5
0BA4 SPACER 1 0KMV HEX. NUT MIOXI.5 T=8
0BAC SET NUT 1 0KMW HEX. NUT MIOXI.5 T=4
0BAE ARBOR COLLAR 1 0KMY HEX. NUT M8X1.25 T=6.5
0BAJ BLADE I 0KQJ CROWN NUT M8XI.25 T=12.5
0BAT NUT 1 0KRQ SERRATED TOOTHED HEX. FLANGE NUT M6XI.0 T=6
0BAU SUPPORTING PLATE 1 0KRX HEXAGON NUT AND FLAT WASHER M6X1.0
0BAY SCREW BAR 1 0KRX HEXAGON NUT AND FLAT WASHER M6XI.0
0BB3 CAUTION LABEL 1 0KTA STRAIN RELIEF
0BB4 WHEEL 1 0L6G POWER CABLE ASS'Y
1
1
1
1
2
6
3
4
2
1
0BPA LOCK KNOB 1 0LSL CIRCUIT BREAKER SWITCH
0G1U DUST SHIELD 4 0LVH SWITCH KEY
0J3P WRENCH HEX 4-64 1 0LVW ROCKER SWITCH
0J3U WRENCH HEX 3-90 1 0QEF MOTOR
0J4F FLAT WASHER _,_8XI6-2 5 I 0QQ0 CLAMP-CORD
0J70 FLAT WASHER 1/4X3/4-7/64 2 0SGC HANDLE BAR
0J76 FLAT WASHER 1/4X3/4-1/16 5 0SRX STIFFENER ASS'Y
0J8D FLAT WASHER 3/8X3/4-5/64 3 0STF PARRLE RING ASS'Y
0J9H SPRING WASHER _,_1/4 6 0STQ HAND WHEEL ASS'Y
0JAE FLAT WASHER _,_6X13-1 2 0STR HAND WHEEL ASS'Y
1
1
1
1
1
2
1
2
1
1
0JC9 SPRING PIN 3-18 1 202U LABEL(Only for 137.248100) 1
0JCA SPRING PIN 3-24 1 20G2 LABEL(Only for 137.218100) 1
0JCA SPRING PIN 3-24 1 21CH CRRE. PAN HD. SCREW & WASHER M5X0.8-10 1
24
/
o_
OBPA
-_. t-
om
O3
O
_3
m
r-
Z
O
(*3
"-4
ko
=_
oo
_=_
=_
"-4
ko
4_
00
(D
(D
10" TABLE SAW
Part list for MOTOR
MODEL NO. 137.218100/137.248100
I.D. NO, DESCRIPTION SIZE QTY
1502 FIELD ASS'Y 1
1503 ARBOR SHAFT 1
0HV5 BALL BEARING 6204LLU 1
0HX9 NEEDLE BEARING 1
0JAL EXT.TOOTH LOCK WASHER _/_4 4
0JEE C-RING 1
0JFY PARALLEL KEY 1
0JX3 HEX. SOC. SET SCREW M5X0.8-8 2
0K3A CR.RE. PAN HD. SCREW & WASHER M5X0.8-30 4
0K5V CR.-RE. COUND.HD.SCREW M4x0.7-8 4
0KCP CR.RE. PAN HEAD TAPPING & WASHER SCREW M5"12-60
0KTH STRAIN RELIEF
0QDZ BEARING RETAINER
0QE9 MOTOR NAMEPLATE
0QEA BRACKET
0QEB COLLAR
0QED SUPPORT PLATE
0QM2 BRUSH HOLDER ASS'Y (t_27"26.5
0QQT BRUSH ASS'Y
0QR0 BRUSH COVER
2
1
1
1
1
1
1
2
2
2
0R1Q MOTOR HOUSING
0R1S BEARING BUSHING
0R1Y ARMATURE ASS'Y
0R20 BAFFLE
0R24 HELIX GEAR
6# 1
1
1
1
1
26
:)l_o
Oq_A
o;
0
_g gg
r-
m
0
m
r-
Z
0
..M
i,o
co
,ram
co
Your Home
For repair-in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
Operator's Manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ®(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR s_
(1-888-784-6427)
Au Canada pour service en fran£ais:
1-800-LE-FOYER Mc
(1-800-533-6937)
www.sears.ca
6EAR6
TM S_,I
® Registered Trademark /Trademark /' Service Mark of Sears, Roebuck and Co.
TM SM
® Marca Registrada /_Marca de Fabrica / ' Marca de Servicio de Sears, Roebuck and Co.
MD
MCMarque de commerce /_ Marque d6posee de Sears, Roebuck and Co. ® Sears, Roebuck and Co.
