Craftsman 137218240 User Manual TABLE SAW Manuals And Guides L0408137

CRAFTSMAN Saw Table Manual L0408137 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

User Manual: Craftsman 137218240 137218240 CRAFTSMAN TABLE SAW - Manuals and Guides View the owners manual for your CRAFTSMAN TABLE SAW #137218240. Home:Tool Parts:Craftsman Parts:Craftsman TABLE SAW Manual

Open the PDF directly: View PDF .
Page Count: 30

Operator's Manual

3.0 HP (Max. Developed)

10" Inch Blade

5000 R.P.M.

JOBSITE SAW

Model: 137.218240

CAUTION:

Before using this Table Saw,

read this manual and follow

all its Safety Rules and

Operating Instructions

•Safety Instructions

• Installation

• Operation

• Maintenance

• Parts List

Customer Help Line

1-800-843-1682

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit our Craftsman website: www.sears.com/craftsman Part No. : 137218240001

SECTION PAGE

Warranty ........................................ 2

Product Specifications ....................... 2

Power Tool Safety ............................ 3

Table Saw Safety .............................. 4

Electrical Requirements and Safety ...... 5

Accessories and Attachments .............. 6

Tools Needed For Assembly ................ 6

Carton Contents .............................. 6

SECTION PAGE

Know Your Table Saw ....................... 8

Assembly and Adjustments ................. 9

Operation ....................................... 16

Maintenance ................................... 20

Troubleshooting Guide ....................... 21

Parts List ........................................ 22

Push Stick Pattern ........................... 30

FULL ONE YEAR WARRANTY

If this Table Saw fails due to a defect in material or workmanship within one year of date of purchase,

Sears will at its option repair or replace it free of charge.

Return this Table Saw to a Sears Service Center for repair, or to place of purchase for replacement.

This warranty gives you specific legal rights, and you may also have other rights which may vary from

state to state.

Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains

chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• Lead from lead-based paints

•Crystalline silica from bricks, cement and other masonry products

•Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure

to these chemicals, work in a well-ventilated area and work with approved safety equipment such as dust masks

that are specially designed to filter out microscopic particles.

• i

MOTOR

HP (Maximum developed) ..... 3.0

Type .................................. Universal

Amps ................................. 15

Voltage .............................. 120

Hz ...................................... 60

RPM (no load) .................... 5000

Overload Protection ............. YES

SAW

Table Size ........................ 26" x 18-1/16"

Table Extensions ............... Right - 5-3/4"

Extension Rip Capacity... 24-7/8" Right Rip

Blade Size ........................ 10"

Rear Outfeed Extension YES

Rip Fence ........................ YES

Miter Gauge ...................... YES

Maximum Cut Depth @ 90°.. 3-1/8"

Maximum Cut Depth @ 45°.. 2-5/8"

Maximum Dado Cut Width... 1/2"

Net Weight ...................... 64.5 LBS

To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.

This table saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt /15 Ampere

time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or

damaged in any way.

Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these

rules could result in serious injury to you or damage to the table saw.

Before using your table saw, it is critical that you read and understand these safety

rules. Failure to follow these rules could result in serious injury or damage to the table saw.

Good safety practices are a combination of common

sense, staying alert and understanding how to use your

power tool. To avoid mistakes that could cause serious

injury, do not plug in your power tool until you have read

and understood the following safety rules:

1. READ and become familiar with this entire

Operator's Manual. LEARN the tool's applications,

limitations and possible hazards.

16.

17.

accessories. The use of improper accessories may

cause injury to you or damage to the tool.

REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool

before turning ON.

NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN THE POWER "OFF". Do not leave the tool

before it comes to a complete stop.

Look for this symbol that

identifies important safety precautions. It means

CAUTION! Become alert, your safety is involved if

you do not follow the safety instructions.

Look for this symbol that

identifies important safety precautions. It means

CAUTION! Become alert, your safety is involved if

you do not follow the safety instructions.

NEVER OPERATE THIS MACHINE WITHOUT THE

SAFETY GUARD IN PLACE FOR ALL THROUGH-

SAWING OPERATIONS.

DO NOT USE IN DANGEROUS ENVIRONMENTS

such as damp or wet locations or exposure to rain.

Keep work area well lighted.

DO NOT use power tools in the presence of

flammable liquids or gases.

18. NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

19.

20.

21.

DO NOT OVERREACH. Keep proper footing and

balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for most efficient and safest performance.

Follow instructions for lubricating and changing

accessories.

CHECK FOR DAMAGED PARTS. Before further

use of the tool, a guard or other part that is damaged

should be carefully checked to ensure it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, mounting and any other conditions that may

affect its safe operation. A guard or other part that is

damaged should be properly repaired or replaced.

7. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents. 22. MAKE WORKSHOP CHILD PROOF with padlocks,

master switches or by removing starter keys.

10.

KEEP CHILDREN AWAY. All visitors should be kept

at a safe distance from the work area.

DO NOT FORCE THE TOOL. It will do the job

better and safer at the rate for which it was

designed.

USE THE RIGHT TOOL. Don't force the tool or

attachment to do a job for which it is not designed.

23.

24.

DO NOT operate the tool if you are under the

influence of any drugs, alcohol or medication that

could impair your ability to use the tool safely.

USE A DUST COLLECTION SYSTEM wherever

possible. Dust generated from certain materials can

be hazardous to your health and in some cases, a

fire hazard. Always operate the power tool in a well-

ventilated area with adequate dust removal.

11. WEAR PROPER APPAREL. DO NOT wear loose

clothing, gloves, neckties, rings, bracelets or other

jewelry which may get caught in moving parts. Non-

slip footwear is recommended. Wear protective hair

covering to contain long hair.

12. WEARA FACE MASK OR DUST MASK. Sawing,

cutting and sanding operations produce dust.

13. DISCONNECT TOOLS before servicing and when

changing accessories such as blades, cutters, etc.

14. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure the switch is in the OFF

position before plugging into the power supply.

15. USE ONLY RECOMMENDED ACCESSORIES.

Consult the Operator's Manual for recommended

25. ALWAYS WEAR EYE PROTECTION. Any power

tool can throw foreign objects into your eyes which

could cause permanent eye damage. ALWAYS wear

safety goggles (not glasses) that comply with ANSI

safety standard Z87.1. Everyday glasses have only

impact resistant lenses. They ARE NOT safety

glasses.

NOTE: Glasses or goggles not in compliance with

ANSI Z87.1 could cause serious injury when they

break.

26. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the blade or

cutter only.

27. DO NOT AUTHORZE ADDITIONAL USERS to

operate this power tool without the accompanying

operators manual for which the user must read &

understand.

ALWAYS USE SAW BLADE GUARD, splitter and 12.

anti-kickback pawls for every operation for which they

can be used, including through-sawing. Through-

sawing operations are those in which the blade cuts

completely through the workpiece when ripping or 13.

cross-cutting.

ALWAYS HOLD WORK FIRMLY against the miter

gauge or rip fence.

USE A PUSH STICK when required. Always use a

push stick when ripping narrow stock. Refer to

ripping instructions in this Operator's Manual where

the push stick is covered in detail. A pattern for

making your own push stick is included on page 30.

NEVER PERFORM ANY OPERATION "FREE

HAND", which means using only your hands to

support or guide the workpiece. Always use either the

fence or the miter gauge to position and guide the

work.

DANGER: FREEHAND CUTTING IS THE MAJOR

CAUSE OF KICK-BACK & FINGER/HAND

AMPUTATIONS.

NEVER STAND or have any part of your body in line

with the path of the saw blade. Keep your hands out

of the saw blade path.

NEVER REACH behind or over the cutting tool for

any reason.

7. NEVER use a rip fence when cross cutting.

8. DO NOT USE a molding head with this saw.

9. FEED WORK INTO THE BLADE against the

direction of rotation only.

10.

11.

NEVER use the rip fence as a cut-off gauge when

cross-cutting.

NEVER ATTEMPT TO FREE A STALLED SAW

BLADE without first turning the saw OFF. Turn

power switch OFF and disconnect the plug from the

power source immediately to prevent motor damage

& before removing material

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

PROVIDE ADEQUATE SUPPORT to the rear and

the sides of the saw table for long or wide

workpieces.

AVOID KICKBACKS (work thrown back towards

you) by keeping the blade sharp, the rip fence

parallel to the saw blade and by keeping the splitter,

anti-kickback pawls and guards in place and

functioning. Do not release work before it has

passed all the way past the saw blade & is off the

table. Do not rip work that is twisted, warped or does

not have a straight edge to guide it along the fence.

AVOID AWKWARD OPERATIONS and hand

positions where a sudden slip could cause your hand

to move into the saw blade.

NEVER USE SOLVENTS to clean plastic parts.

Solvents could possibly dissolve or otherwise

damage the material. Only a soft damp cloth should

be used to clean plastic parts.

MOUNT your table saw on a bench or stand before

performing any cutting operations. Refer to

ASSEMBLY AND ADJUSTMENTS on page 9.

NEVER CUT METALS or materials which may make

hazardous dust.

ALWAYS USE IN WELL-VENTILATED AREA.

Remove sawdust frequently. Clean out sawdust from

the interior of the saw to prevent a potential fire

hazard. Attach a vacuum to the dust port for

additional sawdust removal.

NEVER LEAVE THE SAW running unattended. Do

not leave the saw until it comes to a complete stop.

FOR proper operation follow the instructions in this

Operator's Manual. Failure to provide sawdust fall-

through and removal hole will allow sawdust to build

up in the motor area resulting in a fire hazard and

potential motor damage (see page 10 for details).

DO NOT AUTHORIZE ADDITIONAL USERS to

operate this power tool without the accompanying

operators manual for which the user must read and

understand.

THE REAR OF THE TABLE INSERT MUST BE

FLUSH TO THE TABLE during all sawing

operations. Two different inserts are provided for

regular through-sawing operations and dado cutting

where a rubber adjusting spacer is provided under

the rear of the insert for this purpose.

DO NOT USE A DADO BLADE LARGER THAN 6"

in diameter and ½" in width.

POWER SUPPLY REQUIREMENTS GROUNDING INSTRUCTIONS

To avoid electrical hazards, fire hazards or damage to

the table saw, use proper circuit protection. Always

use a separate electrical circuit for your tools. This

power tool is wired at the factory for 120V operation.

Connect it to a 120V, 15 Amp circuit and use a 15

Amp time delay fuse or circuit breaker. To avoid

shock or fire, replace the cord immediately if it is

worn, cut or damaged in any way.

EXTENSION CORD REQUIREMENTS

Any extension cord must be GROUNDED for safe

operation.

MINIMUM GAUGE FOR EXTENSION CORDS

(AWG type /120 Volt only)

Ampere Rating

Not

More Than

Total length in feet

More Than 25' 50' 100' 150'

6 18 16 16 14

10 18 16 14 12

12 16 16 14 12

@@iii@_i@iiii_i!liiii!liiii!liiii!!iii}iiiil£{i_:_iiliii!iii@iii_i:i:i:ii!ilii}ii!ili!_i_i_i_tt!i_!_ii_:iii

GUIDELINES FOR EXTENSION CORDS

Any extension cord used for power tools MUST be

grounded (3 wire with two flat prongs and one round

ground prong).

Make sure the extension cord is in good condition. When

using an extension cord, make sure you use one heavy

enough to carry the current the tool will draw. An

undersized cord will cause a drop in line voltage resulting

in loss of power and overheating. The table above shows

the correct size to use according to extension cord length

and nameplate ampere rating. If in doubt, use the next

heavier gauge cord. The smaller the gauge number the

heavier the cord.

NOTE: THE 12 TO 16 AMP RATING IS CORRECT FOR

THIS TOOL. IT IS HIGHLIGHTED IN THE TABLE

ABOVE.

Be sure your extension cord is properly wired and in good

condition. Always replace a damaged extension cord or

have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

Before connecting the saw to the extension cord, make

sure the saw switch is turned OFF.

IN THE EVENT OF A MALFUNCTION OR

BREAKDOWN, grounding provides a path of least

resistance for electric current and reduces the risk of

electric shock. This saw is equipped with an electric cord

that has an equipment grounding conductor and a

grounding plug. The plug MUST be plugged into a

matching receptacle that is properly installed and

grounded in accordance with ALL local codes and

ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit

the receptacle, have the proper receptacle installed by a

qualified electrician.

IMPROPER CONNECTION of the equipment grounding

conductor can result in risk of electric shock. The

conductor (wire) with the green insulation (with or without

yellow stripes) is the equipment grounding conductor, tf

repair or replacement of the electric cord or plug is

necessary, DO NOT connect the equipment grounding

conductor to a live terminal.

CHECK with a qualified electrician or service personnel if

you do not completely understand the grounding

instructions, or if you are not sure the saw is properly

grounded.

USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE

3-PRONG GROUNDING PLUGS AND 3-POLE

GROUNDING RECEPTACLES THAT ACCEPT THE

SAW'S PLUG. REPAIR OR REPLACE DAMAGED OR

WORN CORDS IMMEDIATELY.

3-Prong Plug

Properly Grounded

3*Prong Receptacle

Make Sure This

is Connected to a

Known Ground

"" 2-Prong

Receptacle

RECOMMENDED ACCESSORIES

Visit your Sears Hardware Department or see the

Craftsman Power and Hand Tools Catalog to purchase

recommended accessories for this power tool.

To avoid the risk of personal injury:

• Do not use adjustable (wobble) type dadoes or

carbide tipped dado blades.

• Maximum dado width is 1/2".

• Do not use a dado with a diameter larger than 6".

• Do not use molding head set with this saw.

• Do not modify this power tool or use accessories not

recommended by Sears.

UNPACKING AND CHECKING CONTENTS

•For missing or damaged parts on initial

purchase, call 1-800-843-1682

•To order parts, call 1-800-366-7278

Separate all parts from packing materials. Check each

part with the illustration on the next page and the "Table

of Loose Parts" to make certain all items are accounted

for, before discarding any packing material.

If any part is missing or damaged, do not attempt to

assemble the table saw, plug in the power cord, or turn

the switch ON until the missing or damaged part is

obtained and is installed correctly.

TOOLS NEEDED

Medi_m screwddve_

#2 Phillips screwdt vet

Straight edge

Adiustabte w_'ench

Combination squa{e

TABLE OF LOOSE PARTS

ITEM DESCRIPTION QUANTITY

A. Table saw assembly 1

B. Blade 1

C. Blade wrenches 2

D. Miter gauge 1

E. Hex key 1

F. Bolt, flat washer, toothed washer, 1 each

Oval washer, spring washer

G. Blade guard and splitter 1

H. Dado table insert 1

I. Rip fence 1

J. Rear table extension 1

K. Rear table extension tube 2

L. Location seat 4

M. Dome nuts 2

N. Hand wheels 2

O. Table extension 1

P. Dust collector elbow 1

Q. Parallel washer hardware bag 1

STAND:

R. Stand assembly 1

S. Hex. head bolts 4

T. Flat washers 4

U. Roller wheels 2

V. Square neck bolts 2

W. Nuts 2

NOTE: To make assembly easier, keep contents of box

together. Apply a coat of automobile wax to the table.

Wipe all parts thoroughly with a clean dry cloth. This will

reduce friction when pushing the workpeice. To avoid

injury, the styrofoam block should be removed between

the motor and the table.

UNPACKING YOUR TABLE SAW

==a

TheFrontof TableSaw

Bevel angle

Pointer & scale

Blade guard with LED lighting

Miter gauge Cutting line

indicator X

Overload reset

switch

Miter gauge

storage

Rip fence storacie

Table insert

Stand transportation

handle

ON/OFF switch

with safety key

Rip fence

Side table

_xtension

Extension wing

locking lever

._----- Blade tilting

handwheel

Blade bevel

lock knob

Stand roller wheels

Blade elevation

handwheel

Stand Leq Lock nq lever

Stand Iockinq hook

The Rear of Table Saw

j Power cord wrap

STAND ASSEMBLY (Fig. A-l)

1. Release the stand locking hook (1) by sliding it to the left.

2. Unfold the wider leg set on the left side of the stand (2).

Pull the stand locking lever (3) downward and push down

to lock in place.

3. Lift the stand and unfold the narrower leg set on the right

of the saw (4).

4. Pull the lever downward and push down to lock in place.

NOTE:Make sure the stand is locked securely.

Fig. A-1

flat washers onto four hex. head bolts (1) - (Fig. A-2).

Place them through the base mounting holes and

thread into the stand mounting and tighten all four

bolts securely. NOTE: Do not over tighten bolts

holding saw to stand. This may damage the saw base.

Fig. A-2

8 7

ASSEMBLING THE ROLLER WHEELS (Fig. A-l)

Attach one roller wheel (7) to the roller wheel mounting

bracket using a square neck bolt (8) and lock nut (9) as

shown. Repeat for other wheel.

INSTALLING THE DUST COLLECTION ELBOW

(Fig. A-l)

1. Align the lip of the elbow with the slot on the exhaust por

underneath the saw base and install the dust collection

elbow (6) by rotating ¼ turn to lock in position.

NOTE: The elbow can be used to attach a vacuum hose

to remove sawdust from the work area.

ASSEMBLING TABLE SAW TO STAND (Fig. A-1,A-2)

1. Place stand on level surface and adjust the leveling foot

(5) - (Fig. A-2) on the right rear leg of stand to stabilize.

2. Place table saw on the top of stand aligning the mounting

holes in base with mounting holes in stand. Place four

FOLDING THE TABLE SAW/STAND (Fig. A-l, A-3)

1. Rotate the stand locking lever to the left (1) - (Fig. A-1 ).

Lift up on the right side stand locking lever (2) - (Fig. A-2)

to unlock and lift the right side of the table saw up slightly

off the floor, fold up the narrower leg set on the right side

of the saw up to the base of the saw until it snaps into

position on the spring clip.

2. Rest the right side of the saw back onto the floor, release

the left side stand locking lever (3) - (Fig. A-l) and tilt the

saw on its right side, then fold the left side leg set up into

the storage position.

3. Secure the stand legs into position by rotating the stand

locking lever (1) - (Fig. A-l) to the right.

SETTING UP THE TABLE SAW/STAND (Fig. A-3)

1. Rotate the stand locking lever to the left (1) - (Fig. A-1 ).

2. Unfold the wider leg set (left side) and lock the stand

locking lever in place by sliding the lever down the slots

of the mounting bracket and push downward to lock in

place.

3. Rest the left side of the saw onto the floor and lift up on

the right side of the stand and unfold the narrower leg set.

4. Secure the right side legs into position by locking the

stand locking lever in place.

NOTE: Make sure the saw is locked in position as

instructed before operation.

Fig. A-3 _OLD_NG

SET-UP

SAW MOUNTED TO WORK SURFACE (FIG. B)

1. If the leg set will not be used, the saw must be

properly secured to a sturdy workbench using the

four mounting holes at the base of the saw.

2. The surface of the table where the saw is to be

mounted must have a hole large enough to

facilitate sawdust fall-through and removal.

3. Square the saw on the mounting surface and

mark the location of the four 3/8" mounting holes

(1).

4. Drill 3/8" hole into the mounting surface.

5. Mark an 11" square (2) centered between the four

mounting holes (1).

6. Cut out and remove the square.

7. This opening will allow sawdust to fall through the

saw base.

8. Place the saw on the work surface, and align the

mounting holes of the saw with those drilled

through the surface.

9. Fasten the saw to the work surface.

Do not operate this machine on the floor. This is very

dangerous and may cause serious injury.

Fig. B

INSTALLING BATTERY FOR LED WORKLIGHT (FIG.D)

1. Open the cover (1) of the battery box on the top of blade

guard.

2. Install two 1.5V - 3A batteries into the battery box.

3. Secure the cover into the closed position.

4. Turn the on/off switch (2) to the on position to display

the LED light.

Fig. D

BLADE RAISING HANDWHEEL (FIG. E, F)

1. Attach the up ~ down handwheel (1) to the

elevation rod (2) at the front of the saw.

Make sure the slots (3) in the hub of the

handwheel engage with the pins (4).

2. Attach and tighten the dome nut (5 - Fig. F).

Fig. E

Failure to provide the sawdust fall-through hole for

use of the saw when mounted to a work surface and

not the stand will cause sawdust to build up in the

motor area, which may result in fire or cause motor

damage.

ADJUSTING THE CUT LINE INDICATOR (FIG.C)

1. Remove the indicator cover (1) and the two

mounting screws (2).

2. Adjust the indicator to the desired position (3) to

align with the blade.

3. Replace the cover onto the table and replace the

two screws to affix the indicator in position.

NOTE:The cut line indicator was set up at the factory

to be positioned to the right side of the saw blade.

Fig. C

3 2 4

BLADE TILTING HANDWHEEL (FIG. F)

1. Attach the bevel 0° ~ 45 ° handwheel (6) to the

blade tilting rod on the right side of the saw in

the same manner as above.

2. Attach and tighten the handwheel dome nut (5).

Fig. F

RIP FENCE (Fig. G)

1. Lift upward on the rip fence handle (1) so the

rear clamp (2) is fully extended.

2. Place the rip fence on the saw table by engaging

the front of the rip fence first

3. Lower the rear of the fence onto the table.

4. Push down on the fence handle to lock in place.

Fig. G

height by turning the blade raising handwheel

counterclockwise.

3. Place the open-end wrench jaws on the fiats of

the saw arbor to keep the arbor from turning. (Fig.

J) and place the box-end wrench (8) on the arbor

nut (5), and turn counterclockwise.

4. Remove the arbor nut (5) and outer flange (6).

5. Install the saw blade onto the arbor with the blade

teeth pointing toward the front of the saw.

6. Install the flange (6) against the blade and thread

the arbor nut (5) as far as possible by hand.

Ensure that the blade is flush against the inner

side of the blade flange.

INSTALLING AND CHANGING THE BLADE

(FIG. H, I, J)

To avoid injury from an accidental start, make

sure the switch is in the OFF position and the

plug is not connected to the power source

outlet.

To avoid serious injury, table insert must be

level with the table, tf the table insert is not

level with the table, adjust the screw (3) until it

is level with the table. To raise the insert, turn

the screw counterclockwise, to lower the insert,

turn the screw clockwise. Note: A rubber

adjusting spacer is provided under rear of

insert for this purpose.

1. Remove the table insert (1 by removing the two

screws (2, 3). Be careful not to lose the rubber

washer that is on the back screw (3) beneath the

table insert. (Fig. H)

Fig. H

2. Raise the blade arbor (4) (Fig. l) to the maximum

To avoid possible injury and damage to the

workpiece be sure to install the blade with the teeth

pointing toward the front of table in the direction of

the rotation arrow on the blade guard.

Fig. I

Fig. J

To tighten the arbor nut (5) place the open-end

wrench jaws on the fiats of the saw arbor to keep

the arbor from turning. (Fig. J)

Place the box-end wrench (9) on the arbor nut (5),

and turn clockwise (to the rear of the saw table).

Replace the blade insert in the table recess, insert

the screws through the front and rear holes and

tighten remembering the rubber washer under the

rear of the insert..

To avoid injury from a thrown workpiece, blade parts,

or blade contact, never operate saw without the

proper insert in place. Use the original installed

insert for all sawing operations except dado cuts.

Use the dado head insert when using a dado.

BLADE GUARD ASgEMBLY [F_G K. U M

_:_- _

.........i!

J _......... =,. ..

• _ .... .=,= .........

.............4 ;_:.

) °

INSTALLING THE TABLE SIDE EXTENSIONS- cont'd

(FIG O)

6. Snap one location seat (5) over the end of the rear

table extension tube (3). Make sure the locating pin

(6) in the location seat fits into the matching hole in

the extension tube (Fig. O).

7. Install the left hand table extension in a similar way.

NOTE:

For illustration purposes the view in Fig. O looks

"through" the saw table to the under side of the table.

Fig. O

INSTALLING REAR TABLE EXTENSION (FIG. P)

1. Place the rear table extension onto the two rear table

extension tubes (1).

2. Snap two location seats (4) over the two rear table

extension tubes (1).Make sure the locating pin in the

location seat fits into the matching hole (5) in the

extension tube.

3. Insert rear table extension tubes (1) into the two

holes in the rear of the saw table and into extension

tube brackets under the table.

Position rear table support so instruction labels

are up.

4. Snap one location seat (4) over the end of the left

rear table extension tube (1). Make sure the

locating pin in the location seat fits into the

matching hole in the extension tube.

Fig. P

4 3

ADJUSTING REAR TABLE EXTENSION

1. Rear table extension should be positioned as close

as possible to the rear of the table when ripping

short work pieces.

2. Rear table extension should be pulled out fully until

the location seat prevents it from moving outward

when ripping long work pieces that require extra

support as you are completing the cut.

RIP FENCE ADJUSTMENT (FIG. Q)

1. The fence (1) is moved by lifting up on the handle (2)

and sliding the fence to the desired location. Pushing

down on the handle locks the fence in position.

2. Position the fence on the right side of the table, and

along the miter gauge groove.

3. Lock the fence handle. The fence should be parallel

with the miter gauge groove.

4. If adjustment is needed to make the fence parallel to

the groove, do the following:

• Loosen the two screws (3) and lift up on the handle

(2).

• Hold the fence bracket (4) firmly against the front of

the saw table. Move the far end of the fence until it

is parallel with the miter gauge groove.

• Tighten both screws and push the handle to lock.

5. If fence is loose when the handle is in the locked

(downward) position, do the following:

• Move the handle (2) upward and turn the adjusting

nut (5) clockwise until the rear clamp is snug. Do not

turn the adjusting screw more than 1/4 turn at a

time.

• Over-tightening the adjusting screw will cause the

fence to come out of alignment.

I,A WARNING l

Failure to properly align fence can cause "kickback" and

serious injury.

Fig. Q

RIP FENCE INDICATOR ADJUSTMENT (FIG. P)

1. The rip fence indicator (6) points to the

measurement scale (8). The scale shows the

distance between the fence and the blade.

2. Measure the actual distance with a rule. If there is

a difference between the measurement and the

indicator, adjust the indicator (6).

3. Loosen the screw (7) and slide the indicator to the

correct measurement on the scale. Tighten the

screw and re-measure with the rule.

To avoid injury from an accidental start, make sure

the switch is in the OFF position and the plug is not

connected to the power source outlet.

ADJUSTING THE 90°AND 45°POSITIVE STOPS

(FIG.Q-I, Q-2, Q-3)

Your saw has positive stops that will quickly position

the saw blade at 90° to the table. Make adjustments

only if necessary.

90 ° Stop

1. Disconnect the saw from the power source.

2. Turn the blade elevation handwheel and raise

the blade to the maximum elevation.

3. Loosen the blade bevel lock knob (2) and move

the blade to the maximum vertical position, then

tighten the lock knob (2).

4. Place a combination square on the table and

against the blade (1) to determine if the blade is

90 ° to the table. (Fig. Q-2)

5. If the blade is not 90 ° to the table, loosen the two

set screws (4), located on the collar (5)

underneath the table saw, (Fig. Q-3) with the

hex key, and back off the collar..

6. Loosen the bevel lock knob. Turn the blade

tilting handwheel to move the blade until it is 90°

to the table.

7. Adjust the collar (5) so it contacts the bracket (3)

when the blade is 90° to the table. Tighten the

two set screws (4) (Fig.Q-3).

Fig. Q-1

45° Stop

1. With the blade in the upright 90° position, loosen

the bevel lock knob and move the blade to the

45 ° position as far as it will go.

2. Place the combination square on the table as

shown in (Fig.Q-2) to check if the blade is 45 ° to

the table.

3. If the blade is not 45° to the table, loosen the two

set screws (4), located on the collar (5)

underneath the table saw, (Fig. Q-3) with the hex

key, and back off the collar.

4. Tighten the bevel lock knob & secure the screw

(4) until resistance is felt. Do not overtighten.

BLADE TILT POINTER

1. When the blade is positioned at 90°, adjust the

blade tilt pointer to read 0° on the scale.

2. Loosen the mounting screw, position pointer over

0° and tighten the screw.

NOTE: Make a trial cut on scrap wood before

making critical cuts. Measure for exactness.

Fig. Q-3

345

BLADE TILT POINTER

3. When the blade is positioned at 90°, adjust the

blade tilt pointer to read 0° on the scale.

4. Loosen the holding screw, position pointer over 0°

and tighten the screw.

NOTE: Make a trial cut on scrap wood before

making critical cuts. Measure for exactness.

Fig. Q-2

90° 45 °

....._-.__ ::......

BLADE PARALLEL TO THE MITER GAUGE

GROOVE (FIG. R,S)

WARNING I

This adjustment was made at the factory, but it

should be rechecked and adjusted if necessary.

WARNING]

To prevent personal injury:

• Always disconnect plug from the power source

when making any adjustments.

• This adjustment must be correct or kickback

could result in a serious injury and accurate cuts

can not be made.

1. Remove the yellow switch key and unplug the saw.

2. Move the blade guard out of the way.

3. Raise the blade to the highest position and set at

the 0° angle (90 ° straight up).

4. Select and mark, with a felt tip marker, a blade

tooth having a "right set" angle and positioning this

tooth 1/2" above the table at the front of the saw.

5. Place the combination square base (1) into the

right side miter gauge groove (2). (Fig. R)

6. Adjust the rule so it touches the front marked tooth

and lock ruler so it holds its position in the square

assembly.

7. Rotate the blade bringing the marked tooth to the

rear and about 1/2 inch above the blade.

8. Carefully slide the combination square to the rear

until the ruler touches the marked tooth.

9. If the ruler touches the marked tooth at the front

and rear position, no adjustment is needed at this

time. If not, perform the adjustment procedure

described in next section.

Additional blade adjustments (Fig. S)

NOTE: The adjusting nuts are 8mm.

The adjusting mechanism is located above the blade

height adjusting hand wheel under the tabletop. If

the front and rear measurements are not the same,

adjust the alignment by the mechanism as follows:

If the blade is partial to right side:

1. Loosen the two nuts (1) and the right side screw,

then adjust the left side screw.

2. Tighten the nuts (1) and the right screw and

remeasure, as described in steps 4 to 9 in the

prior section.

If the blade is partial to left side:

3. Loosen the two nuts (1) and the left side screw,

then adjust the right screw to its position.

4. Tighten the nuts (1) and the left screw and

remeasure, as described in steps 4 to 9 in the

prior section.

5. Recheck blade clearance making sure that the

blade does not hit the table insert or other parts

when at the 90 ° and 45 ° settings.

Fig. S

Fig. R

BASIC SAW OPERATIONS

ADJUSTING BLADE HEIGHT (FIG. T)

To raise or lower the blade, turn the blade elevation

handwheel (1) to the desired blade height.

Fig. T

1 2

TILTING THE BLADE (FIG. T)

1. To tilt the saw blade for bevel cutting, loosen the

lock knob (2) and turn the tilting handwheel (3) to

the desired angle.

2. Tighten the bevel lock knob (2) to secure the angle.

ON/OFF SWITCH (FIG. U)

The ON /OFF switch has a removable safety key. With

the key removed from the switch, unauthorized and

hazardous use by children and others is minimized.

1. To turn the saw ON, insert key (1) into the slot in the

switch (2). Move the switch upward to the ON

position.

2. To turn the saw OFF, move the switch downward.

3. To lock the switch in the OFF position, grasp the

end of the toggle switch (1) and pull out the safety

switch key.

4. With the switch key removed, the switch will not

operate.

5. If the switch key is removed while the saw is running,

it can be turned OFF but cannot be restarted without

inserting the switch key (1).

Fig. U

OVERLOAD PROTECTION (FIG. V)

This saw has a reset overload relay button (3) that

will restart the motor after it shuts off due to

overloading or low voltage, tf the motor stops during

operation, turn the ON /OFF switch to the OFF

position. Wait for the motor to cool. Push in on the

reset button (3) and turn the switch to the ON position.

To avoid injury, the ON /OFF switch must be in the

OFF position and the plug removed from the power

source while the cool down takes place, to prevent

accidental starting when the reset button is pushed.

Overheating may be caused by misaligned parts or a

dull blade. Inspect your saw for proper setup before

using it again.

USING THE TABLE EXTENSION (FIG. V, V-l)

If the table extension is not parallel with the table.

Remove the bolts (1) and position the parallel washers

(2) between the table extension and tube until it is

parallel with the table, then tighten the bolts.

NOTE: Parallel washer (2) see page 6 for table of

loose parts ITEM: Q.

Fig. V

_,_

NOTE: Move and lock the fence to the 15" left or right

side scale. The fence is now clear of the table.

1. Release the extension lock handles.

2. Slide the extension out until the correct

measurement is displayed on the tube scale. The

user sights the scale off the edge of the table.

3. Tighten both extension lock handles.

Fig. V-1

CUTTING OPERATIONS

There are two basic types of cuts: ripping and

crosscutting. Ripping is cutting along the length and

with the grain of the workpiece. Crosscutting is cutting

either across the width or across the grain of the

workpiece. Neither ripping nor crosscutting may be

done safely freehand. Ripping requires the use of the

rip fence, and crosscutting requires the miter gauge.

Never use a rip fence and miter gauge at the same

time.

5. Slowly feed the workpiece into the blade by pushing

forward only on the workpiece section (1) that will

pass between the blade and the fence. (Fig. W)

AVOID KICKBACK by pushing forward that section of

the workpiece that will pass between the blade and the

fence. Use a push stick at all times.

Fig. W

Before using the saw each and every time, check

the following:

1. Blade is tight on the arbor.

2. Bevel angle lock knob is tight.

3. If ripping, fence lock handle is tight and fence

is parallel to the blade.

4. Blade guard is in place and working properly.

5. Safety glasses are being worn.

The failure to adhere to these common safety rules,

and those printed in the front of this manual, can

greatly increase the likelihood of injury.

RIPPING(FIG. W,X)

To prevent serious injury:

• Never use the miter gauge when ripping.

• Never use more than one rip fence during a single

cut.

• Do not allow familiarity or frequent use of your table

saw to cause careless mistakes. Remember that

even a careless fraction of a second is enough to

cause a severe injury.

• Keep both hands away from the blade and path of

the blade.

• The workpiece must have a straight edge against

the fence and must not be warped, twisted, or

bowed.

• DANGER - Never attempt to pull the workpiece

backwards during a cutting operation. This will

cause kickback and serious injury to the user can

occur.

1. Remove the miter gauge. Secure the rip fence to the

table or if using the extension fence, set the position

and remove all other rip fences from the table..

2. Raise the blade so it is about 1/8" higher than the

top of the workpiece.

3. Place the workpiece flat on the table and against the

fence. Keep the workpiece about 1" away from the

blade.

4. Turn the saw ON and wait for the blade to come up

to speed.

6. Keep your thumbs off the blade top. When both of

your thumbs touch the front edge of the table (2),

finish the cut with a push stick (3). You can make a

push stick using the pattern on page 30 (Fig. X).

7. The push stick (3) should always be used for all

ripping operations for safety (Fig. X).

8. Continue pushing the workpiece with the push stick

until it passes the blade guard and clears the rear of

the table.

9. DANGER - Never attempt to pull the workpiece

backwards during a cutting operation. This will cause

kickback and serious injury to the user can occur.

When the blade completely stops raise the anti-

kickback pawls on each side of the splitter and slide

the workpiece out.

Fig. X

BEVEL RIPPING

This cut is the same as ripped except the blade bevel

angle is set to an angle other than "0".

Cut only with the workpiece and the fence on the right

side of the blade.

turning. Turn the switch OFF, and carefully slide the

)iece out when the blade is completely stopped.

Always position the larger surface of the workpiece on the

table when crosscutting and/or bevel crosscutting to avoid

unstability.

Fig. Y

Never attempt to pull the workpiece backwards during

a cutting operation. This will cause kickback and

serious injury to the user can occur.

RIPPING SMALL PIECES

Avoid injury from the blade contact. Never make

through-saw cuts narrower than 3/4" wide.

1. It is unsafe to rip small pieces. Instead, rip a larger

piece to obtain the size of the desired piece.

2. When a small width is to be ripped, your hand

cannot be safely put between the blade and the rip

fence, therefore, use one or more push sticks to

pass the workpiece completely through and past the

blade.

CROSSCUTTING 90 °MITER ANGLE (FIG. Y)

3 2

BEVEL CROSSCUTTING (FIG. Z)

0°-45 °BLADE BEVEL & 90°MITER ANGLE

This cutting operation is the same as crosscutting

except the blade is at bevel angle other than 0°.

1. Adjust the blade (1) to the desired angle, and

tighten the blade bevel lock knob.

2. Tighten miter lock handle at 90.

To prevent serious injury:

•Do not allow familiarity or frequent use of your table

saw to cause careless mistakes. Remember that

even a careless fraction of a second is enough to

cause a severe injury.

• Keep both hands away from the blade and the path

of the blade.

• DANGER - Never attempt to pull the workpiece

backwards during a cutting operation. This will

cause kickback and serious injury to the user can

occur.

1. Remove the rip fence lower all table extension

fences flush to the table and place the miter gauge

a miter gauge groove on the table.

2. Adjust the blade height so it is 1/8" higher than the

top of the workpiece.

3. Hold the workpiece firmly against the miter gauge

with the blade path in line with the desired cut

location. Move the workpiece to one inch distance

from the blade.

4. Start the saw and wait for the blade (1) to come up to

full speed. Never stand directly inline of the saw blade

path, always stand to the side of the blade that you are

cutting on.

5. Keep the workpiece (2) against the face of the miter

gauge (3) and flat against the table. Then slowly push

the workpiece through the blade. (Fig. Y)

6. Do not try to pull the workpiece back with the blade

Fig. Z 3

COMPOUND MITER CROSSCUTTING (FIG. AA)

00-45 °BLADE BEVEL & 00-45 ° MITER ANGLE

This sawing operation is combining a miter angle with

a bevel angle.

WARNING - Always work to the left side of the blade

during this type of cut. The miter gauge (3) must be in

the left side miter gauge groove. It cannot be used in

the right side groove unless the miter angle is very

sharp, as it will interfere with the blade guard.

1. Set the miter gauge (3) to the desired angle. Use

only the left side groove (2).

2. Set the blade (1) bevel to the desired angle.

3. Carefully push the miter gauge to begin the cutting

operation.

MITERING (FIG. BB) 00-45 ° MITER ANGLE

This sawing operation is the same as crosscutting

except the miter gauge is locked at an angle other

than 90°. WARNING - Always work to the left side of

the blade during this type of cut. The miter gauge (3)

must be in the left side miter gauge groove. It cannot

be used in the right side groove unless the miter angle

is very sharp, as it will interfere with the blade guard.

1. Hold the workpiece (2) firmly against the miter

gauge (3).

2. Feed the workpiece slowly into the blade (1) to

prevent the workpiece from moving.

Fig. CC-1

30"

_- 3/8 _ Thick plywood base

¢o

27"

3/4" Thick pIywood side I__

_:" _ IF_

Attach auxiliary fence to rip fence with two "C" clamps.

(Fig. CC-2)

Fig. CC-2

USING WOOD FACING ON THE RIP FENCE

(FIG. CC)

When performing special cutting operations, you can

add a wood facing (1) to either side of the rip fence (2).

1. Use a smooth straight 3/4" thick wood board (1) that

is as long as the rip fence.

2. Attach the wood facing to the fence with wood screw

(3) through the hole in the fence. A wood fence

should be used when ripping material such as thin

paneling to prevent the material from catching

between the bottom of the fence and the table.

Fig. CC

AUXILIARY FENCE (FIG. CC-1) _ _"

Making the base:

• Start with a piece of 3/8" plywood at least 5-1/2"

wide or wider and 30" long or longer & cut the piece

to shape and size shown.

Making the side:

• Start with a piece of 3/4" plywood at least 2-3/8"

wide or wider and 27" long or longer & cut the piece

to shape and size shown.

• Assembly the pieces together as shown.

• Make sure the screw heads do not stick out from the

bottom of the base, they must be flush or recessed.

The bottom must be flat and smooth enough to rest

on the saw table without rocking.

DADO CUTS (FIG. DD)

1. The dado table insert is included with this saw.

Remove saw blade and blade guard for dado cuts

only. Reinstall and realign blade guard for all

through sawing operations. Install a dado not

exceeding 6" diameter and ½" width and the dado

table insert.

2. Instruction for operating the dado is packed with the

separately purchased dado set.

3. The arbor (1) on this saw restricts the maximum

width of the cut to 1/2".

4. It is not necessary to install the outside flange (2)

before threading on the arbor nut (3) for maximum

½" dado cuts. Make sure that the arbor nut (3) is

tight, and that at least one thread of the arbor sticks

out past the nut.

5. Use only the 6" diameter dado set and keep the

width 1/2" or less. It will be necessary to remove the

blade guard and splitter when using a dado blade

only. Always use caution when operating a dado

blade.

6. Use only the correct number of round outside blades

and inside chippers as shown in the dado set's

instruction manual. Blades/chippers must not

exceed 1/2" total in width.

7. Check saw to ensure that the dado will not strike

the housing, insert, or motor when in operation.

For your

own safety, always replace

the blade, blade guard

assembly, and blade insert

when you are finished with

the dado operation. You

must also realign the blade

guard assembly.

Fig.

MAINTAINING YOUR TABLE SAW

GENERAL MAINTENANCE

Fig. EE

For your own safety, turn the switch OFF and remove

the switch key. Remove the plug from the power source

outlet before maintaining or lubricating your saw.

1. Clean out all sawdust that has accumulated inside the

saw cabinet and the motor.

2. Polish the saw table with an automotive wax to keep

it clean and to make it easier to slide the workpiece.

3. Clean cutting blades with pitch and gum remover.

4. A worn, cut, or damaged power cord should be

replaced immediately.

All electrical or mechanical repairs should be attempted

only by a trained repair technician. Contact the nearest

Sears Service Center for service. Use only identical

replacement parts. Any other parts may create a hazard.

5. Use liquid dish washing detergent and water to clean

all plastic parts.

NOTE: Certain cleaning chemicals can damage

plastic parts.

6. Avoid use of the following cleaning chemicals or

solvents; ammonia and household detergents

containing ammonia.

BLADE RAISING AND TILTING MECHANISM

(FIG. EE)

After each five full hours of operation, the blade raising

mechanism and tilting mechanism should be checked

for looseness, binding, or other abnormalities. With the

saw disconnected from the power source, turn the saw

upside down and alternately pull upward and downward

on the motor unit. Observe any movement of the motor

mounting mechanism. Looseness or play in the blade

raising screw (1) (Fig. EE) should be adjusted as follows:

1. Using a 14mm wrench, loosen the check-nut (2).

2. Adjust nut (3) until it is finger-tight against the

bracket (4), then back off the nut (3) 1/6 turn.

3. Tighten nut (2) with the wrench, while holding nut (3)

in place. Maximum allowable play in and out of the

screw rod (1)is 1/8".

You can place a small amount of dry lubricant on bevel

andgle adjustment rod also. This rod (1) must be kept

clean and free of sawdust, gum, pitch, and other

contaminants for smooth operation.

If excessive looseness is observed in any parts of the

blade raising mechanism or tilting mechanism, take the

complete unit to a Sears Service Center.

LUBRICATION

All motor bearings are permanently lubricated at the

factory and require no additional lubrication.

On all mechanical parts of your table saw where a pivot

or threaded rod are present, lubricate using graphite or

silicone. These dry lubricants will not hold sawdust as

would oil or grease.

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before

making any adjustments.

• Consult your local Sears Service Center if for any reason the motor will not run.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

1. Saw not plugged in 1. Plug in saw

Saw will not start 2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker

3. Cord damaged 3. Have cord replaced by a Sears

Service Center

Does not make accurate 1. Positive stop not adjusted correctly 1. Check blade with square and adjust

45 ° and 90° rip cuts positive stop

2. Tilt angle pointer not set accurately 2. Check blade with square and adjust

to zero

Material pinched blade 1. Rip fence not aligned with blade 1. Check and align rip fence

when ripping 2. Warped wood, edge against fence is 2. Select another piece of wood

not straight

Material binds on splitter 1. Splitter not aligned correctly with blade 1. Check and align splitter with blade

Saw makes unsatisfactory

cuts

Material kicked back from

blade

1. Dull blade

2. Blade mounted backwards

3.Gum or pitch on blade

4. Incorrect blade for work being done

5.Gum or pitch on blade causing erratic

feed

1. Rip fence out of adjustment

2. Splitter not aligned with blade

3. Feeding stock without rip fence

4. Dull blade

5. The operator letting go of material

before it is past saw blade

6. Miter angle lock knob is not tight

1. Sawdust and dirt in raising and tilting

mechanisms

Blade does not raise or tilt 1.

freely

Blade does not come up 1. Extension cord too light or too long 1. Replace with adequate size cord

to speed 2. Low house voltage 2. Contact your electric company

Machine vibrates Tighten all mounting hardware

excessively

Does not make accurate

45 ° and 90° cross cuts

Saw not mounted securely to

workbench

Bench on uneven floor

Damaged saw blade

Miter gauge out of adjustment

1. Replace blade

2. Turn the blade around

3. Remove blade and clean with

turpentine and coarse steel wool

4. Change the blade

5. Clean table with turpentine and

steel wool

1. Align rip fence with miter gauge slot

2. Align splitter with blade

3. Install and use rip fence

4. Replace blade

5. Push material all the way past saw

blade before releasing work

Tighten knob

Brush or blow out loose dust and

dirt

Reposition on flat level surface

Fasten to floor if necessary

Replace blade

Adjust miter gauge

10" JOB SITE TABLE SAW Model : 137.218240

WARNING]

When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product

damage.

WARNINGJ

Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a

qualified service technician. Repair service is available at your nearest Sears Service Center.

PARTS LIST FOR Schematic A

I.D. Description Size Qty

2178 EXTENTION WING (RIGHT) 1

0B3H INSERT 1

0B84 WASHER 1

0B8A WARNING STICK LABEL 1

0B8F CAUTION LABEL 1

0BC2 LOCATION SEAT 2

0BD2 WARNING LABEL 1

0BD3 WARNING LABEL 1

0J5L FLAT WASHER cp5xl 0-0.3 10

...........................od.6v.............................FLATWASHER 3L].6xS4S-o,o22................................................................s.................

0J76

0J95

0JAA

0K8D

0K9U

0KCH

0KCX

0KCY

0KSW

0SZY

FLAT WASHER 1/4x3/4-1/16

SPRING WASHER cp6

WASHER cp8

CR. RE.COUNT HD. TAPPING SCREW M4xl 8-16

HEX. HD. TAPPING SCREW M5xl 6-25

CR.RE. PAN HEAD TAPPING & WASHER SCREW M5x0.8-] 2

CR. RE. PAN HD PLAIN WASHER TAPPING SCREW M5x0.8-]0

CR. RE. PAN HD PLAIN WASHER TAPPING SCREW M5x0.8-] 2

STRAIN RELIEF q_6.1

SLIDING BASE ASS'Y

0SZZ SLIDING BASE ASS'Y 1

0T00 SLIDING BASE ASS'Y

10GN UPPER TUBE

10GP UPPER TUBE

20KA SCALE

20KC SCALE

20WQ HEX. HD. BOLT

211Q SCALE

21HH MITER GAUGE ASS'Y

22KU WARNING LABEL

M6x1.0-50

237U COVER

238S POINTER

26J7 TRADE-MARK LABEL

275A TABLE

275D EXTENSION WING

275E UPPER TUBE

275F LOCATION SEAT

27AD RIP FENCE ASS'Y

27AK BLADE GUARD ASS'Y

27U7 WARNING LABEL

\ I

•+-.+.

IiI

-I

llI

rrl

£I

i,o

10" JOB SITE TABLE SAW Model : 137.218240

PARTS LIST FOR Schematic B

I.D. Description Size Qty

2149 KNOB 1

2759 BODY SHELL 1

2771 ANGLE ROD 1

08VH CLAMP-CORD 1

09JK WRENCHHEX. 1

0B22 HEIGHT REGULATING BOLT 1

0B23 SADDLE 1

0B24 SPRING 1

0B27 POINTER BRACKET 1

0B2B NEEDLE POINTER 1

I.D. Description Size Qty

0JVB HEX. SOC. HD. CAP BOLT M5x0.8-16 1

0JXL HEX. SOC. SETSCREW M10x1.5-12 1

0KOZ HEX. HD. SCREW AND WASHER M8x1.25-16 4

0K16 HEX. HD. SCREW AND WASHER M8x1.25-16 1

0K25 HEX.SOCKET HD.CAP SCREWS M5x0.8-20 1

0K3G CR.RE. PAN HD. SCREW & WASHER M5x0.8-12 1

0K7K CR. RE. ROUND WASHER HD. SCREW M6xl.0-12 2

0K8C CR. RE.COUNT HD. TAPPING SCREW M4x18-10 4

0K8X CR. RE. TRUSS HD. TAPPING SCREW M5x12-12 2

0K9T HEX. HD. TAPPING SCREW M5x16-16 6

0B2E SWITCH BOX

0B3K INSERT

0B3R WRENCH

0B48 WARNING LABEL

0B97 MOTOR BRACKET

0B99 SPACER

0B9C PLUNGER HOUSING

0B9P CLAMP

0B9S BRACKET

0B9W BRACKET

1 0K9U

1 0KA4

1 0KAP

1 0KC8

1 0KDJ

1 0KDR

1 0KDU

2 0KF6

1 0KHZ

1 0KJ4

HEX. HD. TAPPING SCREW M5xl 6-25 4

CR.RE. PAN HD. TAPPING SCREW M4xl 6-16 2

CR.RE. PAN HD. TAPPING SCREW M5x0.8-10 1

CR. RE. TRUSSHD. TAPPING SCREW M4x16-16 2

CR. RE. PAN HD. SCREW M5x0.8-12 2

CR. RE. PAN HD. SCREW M5x0.8-10 1

CR. RE. PAN HD. SCREW M6x1.0-12 2

CR. RE. PAN HD. SCREW M4x0.7-8 2

CAP HD. SQ.NECK BOLT M6x1.0-12 2

CAP HD. SQ.NECK BOLT M6x1.0-35 1

0BA4 SPACER

0BA9 SPACER

0BAB SHIM

0BAC SETNUT

0BAE ARBOR COLLAR

0BAT NUT

0BAU SUPPORTING PLATE

0BAX STIFFENER

0BAY SCREW BAR

0BAZ BEARING SEAT

1 0KJ5

2 0KMR

1 0KMS

1 0KMV

1 0KMW

1 0KMY

1 0KQJ

1 0KRX

1 0KWZ

CAP HD. SQ.NECK BOLT M6Xt .0-80

HEX. NUT M5x0.8 T=4

HEX. NUT M6x1.0 T=5

HEX. NUT M10x1.5 T=8

HEX. NUT M10x1.5 T=4

HEX. NUT MSx1.25 ,T=6.5

CROWN NUT MSx1.25T=I 2.5

HEXAGON NUT AND FLAT WASHER M6x1.0

LEAD WIRE ASS'Y

OBB1 SHAFT 1 OLSL CIRCUIT BREAKER SWITCH 1

0BPA LOCK KNOB

0J3U WRENCH HEX. 3-90

0J4F FLAT WASHER cp8X16-2.5

0J4H FLAT WASHER cpl0x30-0.2

0J6T FLAT WASHER 3/16x3/4-1/16

0J6U FLAT WASHER 3/16xl/2-3/64

0J70 FLAT WASHER 1/4x3/4-7/64

0J76 FLAT WASHER 1/4x3/4-1/16

0J80 FLAT WASHER 5/32x13/323/64

0QEF MOTOR

0S45 ROCKER SWITCH ELEMENT

0STF PARALLEL RING ASS'Y

0T04 CLAMP ASS'Y

232Z STICKER ASS'Y

23PP BLADE

275R LOCATION SEAT

275U SPACER

279M LABEL

0J8D FLAT WASHER 3/8x3/4-5/64 1

0JAE EXTERNAL TOOTH LOCK WASHER cp4 2

0JAF EXTERNAL TOOTH LOCK WASHER cp5 1

0JC9 SPRING PIN 3-18 1

0JCA SPRING PIN 3-24 1

0JCR SPRING PIN 8-90 1

0JED C-RING A-16 1

0JEY E-RING E-9 1

27A1 ROCKER SWITCH

27A2 SWITCH KEY

27QV DEFLECTOR

27U5 LABEL

287H RETAINING CLIP

28CK POWER CABLE

28CY HAND WHEEL ASS'Y

28CZ HAND WHEEL ASS'Y

287A INSTRUCTION MANUAL

.18

Ok _X_

o o

3 0

_' _}

}}

I",3

0i!4

10" JOB SITE TABLE SAW

Part list for MOTOR

Model:137.218240

I.D. No. Description Size Qty

1502 FIELDASS'Y 1

0HX9 NEEDLE BEARING HK-1010 1

0JAL EXT.TOOTH LOCK WASHER cp4 4

0JX3 HEX. SOC. SETSCREW M5x0.8-8 2

0K3A CR.RE. PAN HD. SCREW & WASHER M5x0.8-30 4

0K5V CR.-RE. COUND.HD.SCREW M4x0.7-8 4

0KCP CR.RE. PAN HEAD TAPPING & WASHER SCREW M5x1 2-60 2

0KTH STRAIN RELIEF 1

0QDZ BEARING RETAINER 1

0QE9 MOTOR NAMEPLATE 1

0QEA BRACKET

0QEC ARBOR SHAFT ASS'Y

0QED SUPPORT PLATE

0QM2 BRUSHHOLDER ASS'Y

0QQT BRUSHASS'Y

0QR0 BRUSHCOVER

0R1Q MOTOR HOUSING

0R1S BEARING BUSHING

0R1Y ARMATURE ASS'Y

0R20 BAFFLE

#6 color

-q

ORIY

OR2 %

(_C1

1502

<)<\

o ]S

OQ[}

O(R)

O,X['

-I

Ok!\

.-I

r'-

10" JOB SITE TABLE SAW Model : 137.218240

Part list for STAND

I.D. Description Size Qty

2878 CLAMP HANDLE 4

0lAD WING NUT 1

01AE LEVELING PAD 1

0J4F FLATWASHER (p8X16-2.5 4

0J58 FLATWASHER (p5X14-1 4

0JAZ WAVE WASHER WW-6 2

0K7D CR. RE. ROUND WASHER HD. SCREW M6X1.0-10 2

0K7M CR. RE. ROUND WASHER HD. SCREW M6X1.0-18 1

0KKU CR.RE. PAN HD. ROUND NECK SCREW M5X08-10 1

0KMS HEX. NUT M6X1.0 T=5 1

0KQW LOCK NUT M5X0.8 T=5 1

0KQY LOCK NUT M8X1.25 T=8 6

213T ROLLER WHEEL 2

27DJ PAD 1

27DL HANDLE 1

27DM BRACKET ASS'Y (RIGHT) 1

27DV FOOT PAD 3

27DW DUSTCOLLECTION ELBOW 1

27DY COUPLING 1

27DZ

27E6

27RF

27RQ

27RR

288R

28BU

28BX

BRACKET ASS'Y (LEFT)

HOOK

FOLLOWER PLATE

CAP HD. SO.NECK BOLT

CR.-RE. TRUSSHD. SCREW

HEX. HD. BOLT

CAP

CR. RE. PAN HD PLAIN WASHER TAPPING SCREW

M8X1.25-40

M6X1.0-45

M8X1.25-55

M5X0.8-10

10" JOB SITE TABLE SAW Model : 137.218240

STAND

PUSH STICK CONSTRUCTION

• This is a full-size drawing (actual size)

• Use good quality plywood or solid wood

• Use ½" or ¾" material

• Push stick MUST be thinner than the

width of material being cut

Cut Here To

Push ½"

Wood

Notch To Prevent

Hand From

Slipping

Cut Here To

Push ¾" Wood

Craftsman 137218240 User Manual TABLE SAW Manuals And Guides L0408137

CRAFTSMAN Saw Table Manual L0408137 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation