Craftsman 137224240 User Manual SAW Manuals And Guides L0812164

CRAFTSMAN Saw Band Manual L0812164 CRAFTSMAN Saw Band Owner's Manual, CRAFTSMAN Saw Band installation guides

User Manual: Craftsman 137224240 137224240 CRAFTSMAN SAW - Manuals and Guides View the owners manual for your CRAFTSMAN SAW #137224240. Home:Tool Parts:Craftsman Parts:Craftsman SAW Manual

Open the PDF directly: View PDF PDF.
Page Count: 27

upeira!:o_°s _vJanuaM
14" SAW
MODEL NO.
137.224240
1.5 HP (Max. Developed),
2 speed
1630/2730 RRM. (No load)
CAUTION:
Before using this Band Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions.
Customer He_p Line
I °8,,00=843= 1682
Safety ]nstrucLions
Installation
,, Operation
Maintenance
Parts List
Spanish
Sears, Roebuck and Co., Hoffman Estates, tL 60179 USA
Part No. 137224240001
SECTION PAGE
Warranty ....... ......................................................... 2
Product Specifications ........................... . ......................... 2
Safety ]nstructiQns ................... . .................. .................. 3
Accessories and Attaci_ments ......................... : ........ . ............ 6
Cartoi_ Contents ........ .................................................. 6
Know Your Band Saw ........................................................ 8
Glossary of Terms ........................................ ;............... 9
Assembly and Adjustments ................................................ 10
Operation ............................... : .............................. 18
Maintenance ............................................................ 21
Troubleshooting guide ......................... . .................... : ..... 22
Parts .................................................................. 24
MOTOR
Power source ...... 120 V AC, 60 HZ, 10 AMPS
Horsepower ....... 1.5 HP (Max. Developed)
Speed ........ 1630/2730 F'eet per minute (No load)
Type ............. Induction
DRIVE BELT .......... A 26
CUTTING CAPACITY
Throat ............ 13-5/8"
Height ............ 6" i
BLADE
Width ............
Length ....... :....
TABLE
Size
Tilt
1/8", 1/4", 3/8", 1/2"
91-1/2" to 93-1/2"
............. 16"X 16"
.............. 0 - 15° Left, 0 - 45° Right
DUST COLLECTION ... Yes
NET WEIGHT ......... 230 LBS
To avoid electrical hazards, fire hazards, or damage to
the toot, use proper circuit protection. Use a separate
electrical circuit for your tools.-
The Band Saw is wired at tile factory for 120V operation.
Connect to a 120V, 15 AMP branch circuit and use a 15
AMP time delay fuse or circuit breaker. To avoid shock or
fire, replace power cord immediately if it is worn, cut or
damaged in ally way.
, Some dust created by power sanding sawing, grinding, drilling, and other construction activities Contains chemicals
known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
@ Lead from lead-based paints.
Crystalline silica from bricks and cement and other masonry products, and
Arsenic and chromium from chemically-treated lurnber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work With approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
GENERAL SAFETY iNSTRUCTiONS
BEFORE USnNG THE BAND SAW
Safety is a combination of Comrnorl sense, staying alert
and knowing how to use your band saw.
To avoid mistakes that could cause serious inju.ry, do not
plug the band saw in until you have read and understood
the following:
READ and become familiar with this entire ,nstruction
manual. LEARN the tool's applications, limitations,
and possible hazards
2. KEEP GUARDS IN PLACE and in working order,
,REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habil of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
4. KEEP WORK AREA CLEAN, Cluttered areas and
benches invite accidents.
6.
DON'T USE IN A DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted
KEEP CHILDREN AWAY. All viditors should be kept
at a safe distance from the work area.
7. MAKE WORKSHOP CHILD-PROOF with _adlocks
master switches, or by removing slarter k.e:ys. ,._
8. DON'T FORCE THE TOOL. t will do the job better
and safer at the rate for which it was designed.
9. USE THE RIGHT TOOL Don't force tool or the
attachment to do a job for which it was not designe d.
10. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
, carry the current your product will draw.
An undersized cord will result in a drop in line voltage
and loss of power which will cause the tool to overheat.
The table on page 5 shows the correct size to use
depencling on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The
smaller the gauge nUmber, the heavier the cord.
11. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Non-slip footwear is recommended. Wear protective
hair covering to contain long hair.
12. ALWAYS WEAR EYE
WEAR YOUR PROTECTION, Any band saw
can throw foreign objects into
the eyes that could cause
permanent eye damage.
ALWAYS wear Safety Goggles
(not glasses) that comply with
ANSI safety standard Z87.1. Everyday eyeglasses
have only impact-resistant lenses. They ARE NOT
safety glasses Safety Goggles are available at Sears,
NOTE: Glasses or goggles not in cornpliance with
ANSI Z87.1 could cause senous injury,
13 WEAR A FACE MASK OR DUST MASK. Sawing
operation produces dust.
14. SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than usulg your hand and it
frees both hands to operate tool.
15. DISCONNECT TOOLS before servicing, and when
changing accessories, such as blades, bits, cutters,
and the like.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure the switch is in OFF position
before plugging in.
17 USE RECOMMENDED ACCESSORIES. Consult the
Operator's Manual for the recommended accessories.
The use of improper accessories may cause risk of
injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting blade is unintentionally
contacted.
19. CHECK FOR DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or
other part that is clarnaged should be properly repaired
or replaced.
SAVE THESE NSTRUCT ONS
3
20.
•21.
22.
NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave the tool until it
comes to a complete stop.
DON'T OVERREACH. Keep proper footing and
balance at all tirnes.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing acoessories.
23. DO NOT use power tools in the presence of
flammable liquids orgases.
24. DO NOT operate the toot if you are under the
influence of any drugs, alcohol or medication that
could affect your ability to use the tool properly.
25, Dust generated from certain materials can be
hazardous to your health. Always operate the band
saw in a well-ventilated area and provide for proper
dust removal. Use dust collection systems whenever
possible.
SPECIFIC SAFETY INSTRUCTIONS
.
4.
1. TO AVOID INJURY from unexpected movement, make
sure the saw is on a firm, level surface, properly
secured to prevent rocking. Make sure there is
adequate space for operating. B01tthe saw to a support
surface to.prevent it from slipping, walking, or sliding
during operation, i
i
2. TURN the saw OFF and unplu_l the saw before
moving it.
USE THE CORRECT size and_style of blade.
USE blades rated at 2700 FPM or greater.
MAKE SURE the blade teeth point clown and
towards the table. ;.,-." _,-
6.
rBLADE GUIDES, SUPPORT BEARINGS, AND
BLADE TENSION must be properly adjusted to avoid
accidental blade contact and to minimize blade
breakage. To maximize blade support, always adjust
the upper blade guide and blade guard so that it is
1/8 inch above the workpiece.
7. TABLE LOCK HANDLE should be tight.
8. USE EXTR'A CAUTION with large, very small or
awkward workpieces.
9. USE EXTRA SUPPORTS to prevent workpieces
from sliding off the table top. Never use another person
in place of a table extension, or to provide additional
support for the workpiece.
10. WORKPIECES must be secured so they don't twist,
rock, or slip while being cut.
SAVE THESE
11.
12.
13.
14.
15.
PLAN intricate and small work carefully to avoid
pinching the blade. Avoid awkward operation and
hand positions to prevent accidental contact with the
blade.
SMALL PIECES should be secured with jigs or
fixtures. Do not hand hold pieces that are so small
your fingers are under the blade guard.
SUPPORT round work properl.y (with a V-block or
clamped to the miter gauge) to prevent it from rolling
and the blade from biting.
CUT only one workpiece at a tirne. Make sure the
table is clear of everyttling except the workpiece and
its guides before you turn the saw on.
ALWAYS WATCH the saw run before each use. If
there is excessive vibration or unusual noise, stop
irnmediately. Turn the saw off. Unplug it immediately.
Do not start the saw again until the problem has
been located and corrected.
16. TO FREE any jammed rnaterial, turn the switch OFR
Remove the sw,itch key and unplug the saw. Wait for
all moving parts to stop before removing jammed
material.
17. DON'T LEAVE the work area until all moving parts
are stopped. To childproof the workshop, shut off the
power to rnaster switches and rernove the switch key
from the band saw. Store it in a safe place, away
from children.
For your own safety, read the entire instructiorl manual
before operating the band saw.
1. Wear eye protection.
2. Do not wear gloves, necktie, or loose clotlling.
3. Make sure the saw is on a firm level surface and
properly secured.
4. USE ONLYTHE RECOMMENDED ACCESSORIES.
5. Use extra caution withvery large, very small, or
awkward workpieces.
6. Keep hands away from the blade at all times to
prevent accidental injury.
ELECTRICAL REQUIREMENTS
POWER SUPPLY AND MOTOR SPECIHCATIONS
To avoid electrical hazards, fire hazards, or damage to the
tool, use proper circuit protection. Use a separate electrical
circuit for your tools.Your saw is wired at the factory for
120V operation. Connect to a 120V, 15 Amp circuit and use
a 15 Amp time delay fuse or circuit breaker. To avoid shock or
fire, if power cord is worn or' cut, or darnaged in any way,
have it replaced immediately.
iNSTRUCTIONS
GROUNDING INSTRUCTIONS
This tool must be grounded while in use to protect the
Operator from electrical shock.
IN"['HE EVENT OF A iVIALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This toot is
equipped with an electric cord that has an equipment
grounding conductor and a grounding plug. The plug
MUST be plugged into a matchirlg receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
DO NOT MODIFYTHE PLUG PROVIDED. If it will not fit the
receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipmenl grounding
conductor can result in risk of elechic shock. The
conductor with the green insulation (with or without yellow
stripes) is the equipment grounding conciuctor. If repair or
replacement of the electric cord or plug is necessary, DO
NOT connect the equipment grounding conductor to a live
terminal.
CHEOK with a qualified electrician or service person if you
do not completely understand the grounding instructions, or if
you are not sure the tool is properly grounded
USE ONLY 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept the
tool's plug. Repair or replace darn_.ged or worn cord
immediately, i
Use a separate eiectrical circuit for your tools. This circuit
rnust not be less than #12 wire and should be protected
with a 15 Amp time lag fuse. Before connecting the motor to
the power line, make sure the switch is in tile OFF
position and the electric current is rated the same as the
current stamped on the motor nameplate. Running at a
lower voltage will damage the motor. _,_-. ,._
Fig. A 3-Prong Plug
G,oood,o roog
GUIDEUNES FOR EXTENSION CORDS
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will
result in a drop in line voltage and in loss of power which will
cause the tool to overheat. The table below shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Be sure your extension cord is properly wired and in
good condition. Always replace a damaged extension cord
or have it repaired by a qualified person before using it..
Protect your extension cords flom sharp objects, excessive
heat and damp or wet areas.
Ampere Rating
more l]lan nol more Ihar_
0 6
6 10
10 12
12 16
(when using 120 volls only)
Total length of cord In feet
25' 50' :i00'
18 16 16
18 16 14
16 16 14
14 12
150'
14
12
12
Not recommended
TMs band Saw is for indoor use only. Do not expose to rain
or use in clamp locations.
This tool is intended for use on a circuit that has a
receptacle like the one illustrated in Fig. A
Fig. A shows a 3-prong electrical plug and receptacle
that has a groundihg conductor. If a properly grounded
receptacle is not available, an adapter ( Fig. IB} can be
used to temporarily connect this plug to a 2-contact
ungrounded receptacle. The temporary adapter should be
used only until a properly grounded receptacle can be
installed by a qualified technician. The adapter {Fig. IB}
has a rigid lug extending from it that MUST be connected
to a permanent earth grourld, such as a properly
grounded receptacle box. The Canadian Electrical Code
prohibits the use of adapters.
CAUTION: In all cases, make certain the receptacle is
properly grounded. If you are not sure have a qualified
electrician check the receptacle.
Fig. IB , ,
Grounoing LUg I _'_'---,
(2J_ _¢3 -- Make Sure This
[i_ ;__'_ _j- is COnnected to a
Known Ground
Adapter _ Receptacle
SAVE THESE MNSTRUCTNONS
AVAILABLE ACCESSORIES
Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration or
modification is misuse and could.result in a hazardous
condition leading to possibl e serious injury.
Visit your Sears 14ardware Department or see the Sears
Power and Hand Tool Catalog for the following accessories:
ITEM
Miter gauge
Blade width: 1/8", 1/4", 3/8", 1/2"
Blade length: 91-1/2" to 93-1/2"
Follow inshuctions filat accompany accessories. Use of
improper accessories may cause hazards.
Do not use any accessory unless you have completely
read the insIruction or Operator's Manual for that accessory.
UNPACKING AND CHECKING
CONTENTS
Carefully unpack the band saw and all its partS, and
compare against the list below and the illustration on page 7.
Place the saw on a secure surface and examine it carefully.
" To avoid injury from unexpected Starting, do not plug the
power cord into a power source receptacle during
unpacking and assembly. This cord must remain
unplugged whenever you are assembling or adjusting
the saw.
,, Although compact, this saw is heavy. To avoid back
injury, get help whenever you have to lift the saw.
_' If any part is mis'sing or damaged, do not plug the band
saw in until the rnissing or damaged part is replaced_
and assembly is complete.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION _Q_ANTITY
BAND SAW
A Band saw with motor
B. Table with insert
C. Table trunriions
D. Table hardware
Flex bolts
Lock washers
Table alignment pin
E. Trunnion support bracket
F. Trunnion support hardware
Long bolt
Short hex. bolt
Hex nut
Table lock knobs
Washers
G. Miter gauge
H. Sawdust port
Hex bolts
Washers
I. Power cord hooks
Phillips head bolts
J. Hex. key
K. Stand attachment hardware
Large washers
Hex. nuts
Long hex. bolts
LEG STAND
L. Stand top plate
M. Sled plate
M-1 Back plate
N. Door plate
O. .Tool Tray
R Foot pads
Q. Bag:
Carriage bolts
14ex.nuts
Washers
1
1
2
6
6
1
1
2
1
1
2
2
1
1
2
2
2
2
1
8
4
4
1
2
1
1
1
4
32
32
32
UNPACKING YOUR BAND SAW
BC
%%%
EFG •
H
o'o'
A
M
K
P
©
Q
Upper covet"
ON/OFF switch
Wheel brush
Lower cover
Sawdust .sort
Mounting boles
Upper blade wheel Lower blade
,_ support bearing
Lower blade
guide
Upper blade
support bearing
_'_Table
lock knob
"------ Lower
blade wheel
Blade
Fable insert
Table
Upper guide
bar
L
Upper guide m
lock knob
(
c
Blade guide ---/
slide knob
Table F-_ -= ="
aligning pin t--,J
Table tilt:scale 8
Table trunnion ......
Table tilt stop bolt
Motor--
Table removed for clarity
of illustration
r
Miter gauge storage
Mounting holes _-'_
Stand
o
I
Blade tension
knob
Blade tension
gauge
Blade tracking
knob
Power cord wrap
Motor cord
1
Stand top
plate
CRAFTSMAN BAND SAW TERMS
BLADE GUIDES -Support tile blade and keep it from
twisting during operation. Blade guides must be adjusted
when blade is changed or replaced.
UPPER GUIDE LOCK KNOB -,-locks the upper.slide. Use it
after you adjust the upper guide assembly to make sure
Upper blade guide just clears w0rkpiece before cutting. Upper
guide lock knob must be tightened before the band saw is
turned on.
TABLE LOCK KNOB -locks the table in place.
TILT (BEVEL) SCALE -shows the degree the table is
tilted for bevel cutting.
BLADE TENSION KNOB -- controls the amount of blade
tension when changing blades.
BLADE TRACKING KNOB -adjusts blade position so blade
always runs in the center of the wheel.
SAWDUST PORT -helps keep the machine free from
sawdust. The sawdust port makes.an excellent Ilook-up for
a wet/dry vacuum. _ .
!
i
ON/OFF SWITCH -has a built-in 8hild safety lock. To lock
the switch in the OFF a0sition, remove the switchlkey from
the switch. _
i
WOODWORKING TERMS
BEVEL CUT -An angle cut made through tile face of a
workpiece. _, _..
COMPOUND CUT -A simultaneous bevel and miter cut.
CROSSCUT-A cut made across the width of the
workpiece.
F.P.M.. Feet per minute. Used in reference to the sudace
speed of the saw blade.
FREEHAND - Performing a cut without using a fence
(g'uide), hold-down or other proper device to prevent the
workpiece from twisting during tile cutting operation.
GUM -A sticky sap-based residue from wood products.
HEEL - Misalignment of the blade.
KERF - Tile material removed by a blade in a through cut,
or the slot pr0diJced by the blade in a n0n-through or
partial cut.
LEADING EDGE - The end of the workpiece guided into
the cutting tool first.
MITER CUT - An angle cut made across the width of a
workpiece.
RESAW -A cutting operation to reduce the thickness of
the workpiece to make thinner workpieces.
RESIN -A sticky sap that has hardened.
RIPPING CUT -A cutting operation along the length of the
workpiece.
R.P.M. -Revolutions per rninute. The number of turns
completed by a spinning object in one minute.
SAW BLADE PATH -The area of the workpiece or table
top directly in line wit!] the travel of the blade or the part of
the workpiece which will be cut.
SET -The distance between two saw blade teeth tips, that
are bent outward in opposite directions tO each other. The
further apart the tips are, the greater the set.
TRAILING END -The workpiece end last cut by the blade.
WORKPIECE - The item being cut. The surfaces of a
workpiece are commonly referred to as faces, ends, edges.
WORKTABLE -The surface on which the workpiece rests
while performing a cutting or sanding operation.
Keli Leading,_ Sawblade Pall]
Surface
Workpiece Trailing Edge
ASSEMBLY NSTRUCTRONS
TOOLS NEEDED
Phillips screwdriver
Adjuslable wrench
'Combinationsquare
EEI__-3__ZLI_--_LTJ___Z[2-1__21
Straight edge
Feeler'gauge - size 0.02
For your safety, never connect plug to power source
receptacle until all assembly and adjustment steps are
completed, and you have read and understood the safety
and operating instructior/s.
CLOSED STAND ASSEMBLY (Fig. C)
1. Attach LH. side plate(3) to the top plate (1) with four
carriage Screw (10), flat washer(11) and hex. Nut(12):
2. Repeat above steps for the R.H.: Plate(4).
3. Attach tools tray(2) between the, L.H. Side plate and R.FI.
side plate with eight carriage sc!ew(lO), flat washer (11)
and He)(. Nut(12).
Attach back plate(5) to the top plate(l) and tools tray(2)
with four set screw(9).
Mount the door plate(6) :to the R.14.Side plate(4) and
fasten with four set screw (9).
Fit knob(15) to the door plate(6) with one Hex. Screw (14).
Place four pad(13) to each leg.
4,
5.
6.
7.
Fig. C
Although compact, this saw is heavy. [b avoid back injury, ge
help to lift the saw.
ASSEMBLE BAND SAW TO LEG STAND (Fig. l
1. Lift the saw body (1) and place on tile leg stand (2),
aligning the mounting holes (3) of the saw base with the
foul" mounting holes of ttie leg stand top plate.
2. Attach timeband saw to the stand with four long hex heac
bolts (4) and four flat washers (5).
3. Place a flat washer (5) arid hex nut (6) on each bolt from
the underside. Hand tighten.
4. Tighten all mounting bolts and nuts with a wrench.
5. Tighten all leg stand bolts and nuts with the wrench.
Fig. D
6
o
o
i
i
f
i
i
o
THE SAWDUST PORT (Fig. E )
The sawdust port has a 2-1/2"(O.D)/2-1/4"(I.D) diameter opel
ing, suitable for attaching to a wet/dry vacuLIm hose to hell
keep the work area free of sawdust.
1. Remove the bolts (1) and washers (2) from the sawdust
port (3).
2. Open the lower wheel cover (4.).
3. Attach the sawdust port to the edge of timewheel cover,
using the same hex. head bolts and washers.
4. Tighten timebolts and close the cover.
I
ASSEMIBLE THE £_AND SAWTABLE (Fig. F, G, H, I,}
Mounting the trunnion support bracket (Fig. F )
1. Remove the Iwo hex head bolts (1) and washers (2),
located, on the lower band saw housing.
2. Place the trunnion support bracket (3) on the saw body,
as shown, aligning the mounting holes.
3. Place the washers oil the hex head bolts, and insert into
the threaded holes, through the bracket and saw body.
Tighten.
4. Thread a nut (4) onto the table stop bolt (5) and screw
both into the rear tab (6) on the trunnion support bracket.
5. Tighten the nut down onto the bracket tab.
Fig. F
1
2
6
1112 _-_ - ._._..__. --
1o
7-
9 -
9. Turn the table right side up.
10. Remove the table insert (13) frorn the table.
11. Guide the table slot (14) over the saw blade and rotate a
1/4 turn, so the slot is perpendicular to the blade.
12. Placing the scale lock knob bolts (10) through the
trunnion brackel holes (15) as shown, lower the table
onto the trunnion bracket.
Fig. H
f •
10
15
13. Place a lock knob (16) on each scale knob bolt. Adjust
the table by aligning the zero scale rnark to the scale
pointer (17), and tighten the knobs.
14. Replace the table insert (13), aligning the indents.
15. Place the table aligning pin (18) in the hole at the front of
the table, and tighten.
Mounting the tame (Fig. G, H, i}
6. On the underside of the table (7), place the scale
brackets (8) on the bracket mounting ho}es (9).
7. Be sure the long loci< knob bolts (10) are placed
upwards through the bracket slots as shown.
8, Place lock washers (11) on three short hex head
bolts (12). Thread thebolts through the mounting holes
and tighten,
16
INSTALLING AND REMOVRNG BLADES (Fig. J)
To avoid injury from accidental starting, always turn the
switch C)FF and remove the plug frorn the power source
before moving, replacing, or adjusting the blade.
Removing
1. Loosen the blade tension by turning the blade tension
knob (1) counterclockwise.
2. Remove the table insert (2) and remove the table
aligning pin (3) from the table.
3. Open the upper and lower wheel cover doors (4).
4. Loosen the two Phillips screws (5) and remove the upper
blade guard (6).
5. Remove tile blade (7) frorn tile upperand lower blade
guides (8).
6. Carefully pull the blade from tile side slot (9) and from
the wheels (1.0).
7. Swing the left side of the blade toward you, turning the
blade so it will fit through the slot (11) in the table, and
rernove.
Fig. J
10
\6
5
8
Installing
1. Make sure the blade tension knob (1) is turned
counterclockwise until it stops.
2. Remove old blade as explained in "Removing".
3. Guide the new.blade (7) througb the table slot (11). '
Make sure the blade teeth are pointing forwat:d and
down.
NOTE: To avoid lifting the workl:)iece, the blade teeth
must point downward toward the table.
4. Swinging the left side off the blade away and back, place
the blade on the upper and lower wheels (10).
5. Place the blade carefully between the upper and lower
blade guides (8).
6+ Slide the blade ir_tothe slot (9) at the left of the wheels,
and make sure the blade is positioned at the middle of
tile wheels. .'
7. Turning the blade tension knob (1) clockwise, tigtlten the
tension until the blade is tight on the wheels.
8. Replace the table insert (2) and the table aligning pin (3),
9. Adjust the blade tracking and tension properly (See
ADJUSTMENT INSTRUCTIONS section) before
operating the band saw.
To avoid injury, the blade tension, tracking, and upper and
lower guides and bearings must be properly adjusted before
operating the band saw. (See ADJUSTMENT
INSTRUCTIONS section)
MITER GAUGE (Fig. K)
A miter gauge (1) is supplied with your band saw to be used
in the table slot (2) on the right side of the blade. The miter
gauge can be tilted 0° and to 45° right or left, to maintain a
accurate angle for your workpiece. A bracket is provided on
the leg stand for convenient miter gauge storage.
3
8
10
Fig. K
1 --
("_' t
Before operation always make sure the blade is in center
of table insert slot.
iNSTALLPOWERCORDBRACKETS(Fig,L)
1. Powercordbrackets(1)areprovidectforconvenient
cordstorage.Atlachthepowercordbracketstotheback
ofthesawbocty,asshown,withtwoPhillipshead
screws(2).Tighten.
2. Wrapthepowercordontothebracketswhentheband
sawis not ill use, to prevent damage to the cord.
Fig. L
ADJUSTMENT gNSTRUCT ONS
To avoid injury, turn the switch OFF and unplug the barld saw
from the power source before making any adjustments.
TABLE ADJUSTMENTS (Fig. M, N)
Tilting the table (F_g. IBm) i
The band saw table (1) tills 0° an@to 45° right
1. Loosen both table lock knobs (2) undemeath:the table.
2. Tilt the table to the desired angle on the scale (3)
underneath the table.
3. Tighten the two table lock knobs.
ADJUSTING THE 90 ° TABLE STOP (Fig. N)
1. Loosen the table lock knobs (2) and tilt the table to
the right.
2. Loosen the nut (4) on the table stop bolt (5) and lower
the stop bolt as far as possible.
3. Tilt the table until it rests on the stop bolt.
4.. Place a combination square (6) on the table with the
heel of the square against the saw blade.
5. Adjust the tilt of the table left or right until it is 90° to the
blade. Make sure there is no space between the square
and the blade.Tighten the table lock knobs.
6. Adjust the table stop bolt up until it touches the table.
Tighten the jarn nut down to the support bracket,
7. Loosen the lock knobsand see that the table is resting
on the stop bolt.
8. Check the scluare to make sure the table is still square to
the blade. If not, readjust the stop bolt.
9. When the adjustment is accurate at 90°, align the
pointer (7) to 0° on the scale (8).
2 4
Make sure the blade is in center of table insert slot(2)
Then tighten the screw(A-C) which are under the table on
both sides as shown (Fig O.)
Fig. O
_, 13
ADJUSTMENT INSTRUCT ONS
To avoid injury, turn the switch OFF and unplug the band
saw fiom the power source before making any
adjustments.
TSLTmNGTHE TABLE t_Fig. P)
Tile band saw table (1) tilts 0° to 45° to tile right and 15° to
the left.
!. Loosen both star handle lock knobs (2) underneath the
table.
2. Tilt tile table to the desired angle as shown on the
scale (3).
3. Tighten the two loci< knobs.
NOTE: The 90° table slop bolt must be removed to tilt
the table 10° or more to the left.
Fig. P
ADJUS'NNG THE 90° TABLE STOP (Fig. q),,:..
1.
O
t'_,
Tilt the table to the front of the band saw.
Loosen the jam nut (1) on the table stop bolt (2) and
lower the stop bolt.
3. Tilt the table to the back until it rests on tile stop bolt.
4. Place a combination square (3) on the table with the
heel of the square against the blade (4.).
5. Adjust the tilt of the table until it is 90° to the blade and
there is no space between the square and the blade.
Tighten the lock knobs.
6. Adjust the table stop boli (2) up until it touches the
table. Tighten the jam nut (1).
7. Loosen the lock knobs and see if the table is resting
on the stop bolt.
8. Check the square to make sure the table is still square
to the blade. If not, readjust the stop bolt.
9. When the adjustment is accurate at 90°, align the
pointer (5) on the scale (6) to 0°.
NOTE: The table stop,bolt must be removed to tilt the
table 10 °or more to the left.
Fig. Qx__/
BLADE TENSION (Fig. i_)
To avoid injury, turn the switch OFF and disconnect the
saw from the power source before making any
adjustments. NEVER rnake tension adjustnqentswith the
machine running.
The gauge (1) on the bracket (2) at the rear of the upper
wheel indicates the proper tension for the various blade
widths.
1. Set the blade tension gauge (1) to correspond with the
blade width, as shown.
2. Turn the blade tension knob (3) clockwise to tighten
the blade, counterclockwise to loosen.
3. As you become familiar with the saw, you may want to
change the tension settings.
NOTE: Changes in blade width and type of material
being cut will have an effect on the blade tension.
Too much or too little tension could break the blade.
Fig. R
2
1
BLADE TRACKING (F_g. S)
To avoid injury, turn the switch OFF and disconnect the
saw from the power source before making any adjustments.
NEVER make tracking adjustments with the machine
running.
1. The blade (!) must be tensioned properly before
adjusting the tracking. (See BLADE TENSION on page 15).
2. Open the upper cover, o..
3. Move tile blade guides (2) and support bearings (3)
away frorn tile blade, if necessary. (See page 17).
4. Rotate the wheel (4) slowly forward by hand, and
check the position of the blade on the wheel. The blade
should remain centered on the wheel as it turns.
5. If the blade moves toward the front of the wheel, turn
the tracking knob (5) on the rear of the band saw
clockwise. This tilts the top of the wheel and moves the
blade toward the center.
6. If the blade moves toward tile back edge, turn the
tracking knob counterclockwise, moving the blade
toward the center.
NOTE: Turn the tracking knob SLIGHTLY to make blade
tracking adjustments.
Fig: S
UPPER BLADE GUIDE ASSEMBLY (Fig. T}
To avoid injury, turn the switch OFF and disconnect the
saw from the power source before making any
adjustments. NEVER make adjustrnents with the machine
running.
1. Loosen tile lock knob (1) and move the blade guide
assembly (2) to 1/8" above the workpiece.
2. Rotate the assembly, if necessary, until the guide ,
blocks (3) are flat (parallel) to the blade (4). Tighten the
lock knob.
Fig. T
3
4¸
-t '2
2
1
UPPER BLADE GUIDES AND BLADE SUPPORT
BEARING (Fig. U, V)
The blade guard has been removed for clarity of illustration.
To avoid injury never o,perate the band saw without all guards
in place and in working order.
To avoid injury, turn the switch OFF and disconnect the saw
from the power source before making any adjustments.
NEVER make adjustments with the machine running.
NOTE: Make sure the blade is tensioned and tracking
properly. Adjust the blade guides and support bearing after
each blade tension and tracking adjustment. When the upper
blade guides and support bearings are adjusted, the lower
guides and bearings should also be adjusted.
Blade guides (Fig. U)
1. Make sure the blade is tensioned and trackingproperly.
2. Loosen the front hex socket screws (1) with a hex
wrench.
3. Move the guide blocks (2) as close to the blade (3) as
possible without pinching it.
4. Using a feeler gauge, make sure the space between
guide block and the blade measures 0.02" (the thickness
r
of a dollar bill).
5. Tighten the hex socket screws.
6. Loosen tile side thumb screw (4)by turning
counterc!ockwisel
7. [iJrn the rear knob (5) to move tl)e blade guide brackets
in or out until the guide blocks !2) are just behind the
blade teeth.
8. Tighten the thumb screw.
Support bearing (Fig, V)
9. Loosen the thumb screw (6).
10. Turning the rear knob (7), move the support bearing (8)
in or out, until the bearing is 1/64" behind the blade.
11. Tighten the thumb screw (6).
Fig. U
-L
NOTE: The blade support bearing prevents the blade
from moving back too far and damaging the saw teeth
setting.
12. Check the lateral position of the support bearing (8).
The vertical back edge of the blade (3) should overlap
the front face of the support bearing 1/16" to 1/8" to
the left of the right bearing edge, as shown.
3'
2
Fig. V
(
' _::.:'i::'::: _' ::::::::::::::::::::: 16 .....................................................................................................................................
LOWERBLADEGUiDESANDSUPPORTBEARING
(Fig. W, X)
To avoid injury, turn the switch OFF and disconnect the
saw from the power source before making any
adjustments. NEVER make acljustments will] the machine
running.
NOTE: Make sure the blade is tensioned and tracking
properly. Tile lower blade guides and support bearings
should always be adjusted after the blade is tensioned, the
tracking is adjusted, and the upper blade guides and upper
support beanngs are properly adjusted.
Blade guides
1. Loosen both front hex socket screws (1) with a hex
wrench.
2. Move tile guide blocks (2) as close to the sides of the
blade (3) as possible without pinc!ling it.
3. Using the feeler gauge, measure the spaces between
the guide blocks and the blade. Adjust to 0.02".
4. Tighten the hex screws. (Fig. W)
5. Loosen lhe side hex socket screw (4). Move tile guide
block support bracket (6) in or out until the blocks are
just behind the saw teeth. Tighten the screw. (Fig. X)
Support bearing
6. Loosen the bearing hex socket screw (7) with the hex
wrench.
7. Move the blade support bearing shaft (8) in or out until
the support bearing (9) is 1/64"; behind the saw blade.
8. Tighten the bearing hex socketiscrew. (Fig. X)
9. The back edge of the blade (3)Ishould be positioned
1/16"to 1/8" from the right edge of the support bearing
(9), as shown. (Fig. W)
PULLEY ALIGNMENT (Fig. Y)
Tile pulley alignment has been factory adjusted and
shouldn't require further adjustrnent. If adjustnlents are
required or belt needs replacing fo ow thes6 p o_edu es
1. Place a straight edge in the front groove of both pulley s,
behind the blade wheel.
2. Turn the hex socket screw (1) in the side of the nlotor
pulley (2) to loosen the pulley on the shaft.
3. Adjust the motor pulley in or out on the motor shaft (3) to
align the edges of tile two pulleys.
4. When aligned, tiglqten tile hex socket screw on the side
of the motor pulley.
Fig.W
\
\
Fig. X
Fig. Y
f
[
7 8
1
2
E:]ASNC SAW OPERATF ONS
"ON/OFF" SWFTCH (Fig.. Z)
The keyed switch is intended to prevent unauthorized
use of the band saw.
1. 7o turn the band saw ON insert the yellow key (1) into
the key slot (2) in the center of ttfe switch.
2. Push the key firmly into theslot, then push switch
to the ON position to start the band saw.
3. To tLirn lhe band saw OFF push the switch to the
down position.
4. Remove the yellow switch key, when the saw has come
to a complete stop., by gently pulling it outward.
Renlove the switch key whenever the saw is not in use.
Place it in a safe place and out of reach of children.
Fig. Z
I
GENERAL CUTTING
For your safety, read and understand all GENERAL and
SPECIFIC SAFETY INSTRUCTIONS on pages 3-5 before
using the band saw.
Operating band saws involves a certain amount of hazard.'
Before attempting regular work, Use scrap lumber to check
the settings, and to get the feel of operating the band saw.
Read instructions and plan your work before cutting a
workpiece.
Do not turn the power ON until after you have made all •
adjustments, checked that the guard is in place, and turned
the wheel by hand Io make sure all parts workproperly.
Always keep the guide assembly 1/8" above the workpiece.
Do not force the workpiece against the blade. Light contact
permits easier cutting and prevents unwanted friction and
heating of the blade.
Sharp saw blades need little pressure for cutting. Steadily
move the workpiece against the blade without forcing it.
7b avoid twisting the blade do not turn sharp corners; saw
around corners.
A band saw is basically a "curve-cutting" saw, It is not
capable of doing intricate inside cutting as can be done
with a scroll saw.
It is also Llse'dfor straight line operations such as
crosscutting, ripping, mitering, beveling, compound cutting,
and resawing.
7
To avoid blade breakage, fire or other damage or injury,
NEVER use this band saw to cutmetals.
CUTTING CURVES
When cutting curves, carefully turn the workplece so the
blade follows without twisting. If the curve is so sharp that
you repeatedly back up and cut new kerf use a narrower
blade, or a blade with more set (teeth further apart). When
a blade has more set, the workpiece turns easier but the
cut is rougher.
When changing a cut, do not wittTdraw the workpiece frorn
the blade. The blade may _:jetdrawn of[ the wheels,
To change a cut, turn the workpiece and saw out through
the scrap material area.
When cutting long curves, make relief cuts as you go
along.
CIRCLE CUTTING (Fig. AA)
1. Adjust the guide assembly to 1/8" above the workpiece.
2. Use both hands while feeding the work into the blade
Hold the workpiece firmly against the table. Use gentle
pressure: Do not force the work, ALLOW the blade to cut.
3. Tt7e smallest diameter circle that can be cut is
determined by the width of the blade. For example_ a
1/4" wide blade will cut a minimum diameter of
approximately 1-1/2".
Fig. AA
MinirlTum
2-112"D Circle Diameler
1/Z' Blade Width
18 i;-:::S:.!7:
EIL.ADKSE1LEC'TIO_Fig. E_B
CAUTION:Bladeteetha_"eSharp.Usecarewhenhandling
asawblade.
Forlongestwearandbestcuttingresults,usethecorrect
,blade tMckness, width, and teml:?er for the type of material
you will cut.
When sawing small curves and delicate work, use narrow
blades. Otherwise, use tl_ widest blade possible. See Fig. AA
on page i 8. ..
For cutting wood and similar rnaterials with this band saw,
purchase blades in widths up to 1/2", and a length of
93-1/2".
Do not cut metals with this band saw.
Common causes of blade break.age:
Poor guide alignment and adiustment.
Forcing or twisting a wide blade around a short radius.
_, Feeding too fast.
Dull teeth or not enough set.
_, lbo much blade tension.
_, Setting top guide assembly too high above the
workpiece.
o Lumpy or improperly finished braze or weld on the
blade.
- Continuous running of blade when not cutting.
Fig. BEi
Operation Recommended BSadeW_d_th
(_nehe_}
Cross Cutting 1/4, 3/8, t/2
Mitering 1/4, 3/8, 1/2
Beveling 1/4, 3/8, 1/2
Compound Cutting 1/4, 3/8, t/2
Circle Cutting See chart on pg. 18
Curve Cutting 1/8, _1/4
i
CHANGING SPEED SETTING (Fig. CC}_
To avoid injuries, turn the power switch OFF and
disconnect the band saw from the power source]
1. Loosen the belt tension by turning the tension lock
handle(5).
2. Open the lower wheel covet and re-position the
V-bell(3).
Fig, CO
534
3hanging the speed from 1630 to 2730 FPM: first remove
_elt(3) from the band saw pulley(4); reposilion in the saw
:_ulleygroove(I).
3hange I:hespeed frorn 2730 to 1630 FPM: first remove
_elt(3) Irolll the motor pulley(5) and reposition in the motor
_ulley groove(2). Rernove the bell from the saw pulley (4)
:_ndreposition in the saw pulley groove(2).
}. Tighten lhe belt tension by turninq the tension lock
handle(6).
_OTE: After re:adjusling belt posil.ion and belt tension,
verify and re'-adjusl the setl:ings for the blade tension
and tracking position, guides and bearings (See
\djusimenl section).
19
Applyathir_coatofpastewaxonthetablesothatthewood
slideseasilywhilecutting.
TO INSTALL A NEW BELT (Fig. DD)
1. Open the lower wheel door.
2. Loosen the blade tension by turning the blade tension
lock knob (t).
3. Remove tile blade from the lower blade wheel.
4. Loosen and remove the hex head bolt (2) and flange (3)
on the lower blade wheel.
5. Remove tile lower blade wheel. '-
6. Turn the belt tension handle (4) on the rear of the saw
tlousing to loosen the v-belt tension.
7. Remove the v-belt (5).
8. Check the alignment of the two pulleys.
9. If the edges of the two pulleys are not aligned, see
"ALIGN THE PULLEYS" in ADJUSTMENT section.
10. Place the new v-belt on the saw pulley and the motor
pulley. See OPERATION section "CHANGING SPEED
SETTINGS" on page 19 for proper belt placement.
i 1. When positioned properly, tighten the v-belt tension by
turning tile tension lock handle.
NOTE: The pulley belt is properly tensioned when there
is 1/2" deflection if pressed in tile center between the
pulleys.
BLADE WHEEL TIRES
Pitch and sawdust that build up on the tires should be
removed with a stiff brush or scrape off with a piece of wood.
NOTE: To avoid damaging the tires do not use a sharp knife
or any kind of solvent,
When the tires become worn they should be replaced. When
replacing tt]e tires, stretch them around the wheels but do
not glue thern on.
MOTOR
Frequently blow or vacuum out any sawdust from the motor.
Follow lubrication instruction on the motor label.
To avoid electrocution or fire, immediately replace a worn, cut
or damaged power cord.
LUBRICATION
All of the bearings are packed with grease at the factory.
They require no further lubrication.
CAUTION: Never put lubricants on tile blade while it is
spinning.
12. Replace the blade wheel. Push the wheel in firmly until
it is louching the saw pulley. Replace and tighten the
flange and nut.
13. Reinstall tile blade (See INSTALLING BLADES Section
on page 12). i
14. Adjust the blade tension, tracking, ;and the upper and
lower blade guides and bearings b'efore operating the
band saw. "
To avoid injury, the blade tension, tracking, and upper and
lower guides and bearings must be properly adjusted before
operating the band saw. (See ADJUSTMENT INSTRI.JCT!ONS
section) 1
Fig. DD
4
_-' 3
....
5
GENERAL MADNTENAINC, E
For your own safety, turn switch OFF and remove the plug
from power source receptacle before maintaining, cleaning,
adjusting, or lubricating your band saw.
To avoid fire or toxic reaction, never use gasoline, naphtha,
acetone, lacquer thinner or similar highly volatile solvents
to clean the band saw.
To avoid eye injury from blowing debris, weal safety
goggles when blowing out sawdust.
ADJUSTINGTHE UPPER BLADE GU_DETRAVEL (Fig. EE)
If the upper guide bar assembly will not move up and down
easily or falls when the lock knob is loosened, the following
adjustment should be performed.
1. Remove the guide bar lock knob (1);
2. Using a 5mm hex "L" wrench, tighten or loosen the
screw (2) located behind the lock knob.
3. Move the guide bar (3) up and down to ct-leck for smooth
rnovernent and ability to hold its position.
4. Make further adjustments .to the screw as required.
Properly adjusted, the guide bar should move smoothly
and hold its position when released.
5. Reinstall the guide bar lock knob.
Fig, EE
BAND SAW
Sawdust will accumulate under the table and base. This
could cause difficulty in the movement of the table when
setting up a band saw cut. Frequently blow out or vacuurn
up the sawdust.
Keep your band saw clean. Remove the sawdust from the
inside. Vacuum or blow out flequently.
Do not allow debris :Eobuild up on theetable, the guides, or the
support bearings. Clean them with draftsman Gum and
Pitch Remover.
NOTE: Do not immerse the support_bearings in the gum
p
an_._itch remover.
Apply a thin coat of paste wax.on the table so that the wood
slides easily while cutting.
_!... _,_
BLADE WHEEL TIRES
Pitch and sawdust that build up on the tires should be
removed with a stiff brush or scraped off with a piece of
wood.
NOTE: To avoid damaging the tires do not use a sharp
knife or any Mnd of solvent.
When the tires become worn t.tTeyshould be replaced.
.When replacing the tires, stretch them around the wheels
but do not glue them on.
LUBRJCATnON
All of the bearings are packed with grease at the factory.
They require no further lubrication.
CAUTION: Never put lubricants on the blade while it is
spinning.
MOTOR
Frequently blow or vacuum out any sawdust from the
motor. Follow lubrication instruction on the motor label.
To avoid electrocution or fire, immediately replace a worn,
cut or damaged power cord.
To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before
making any adjustments.
.
All electrical or rne(;hanical repairs should be done only by qualified service technicians, Contact the nearest Sears
Service Center.
GENERAL
Problem
Blade does not run in the
center of the
upper wheel.
Band saw slows down
when cutting.
Blades braking
Blade dulls too quickly.
Band saw vibrates.
Probable Cause
1. Not tracking properly.
2. Defective blade.
1. Belt too loose.
2. Cuttirlg too small a radius.
!
3. Ddlll blade.
i
4. O_'erloading motor.
1. Too much tension on
the blade.
2. Kink in the blade caused by
cutting too small a radius or
turning thr_'_aterial too fast
when cutting.
1. Blade guides set too close to
the teeth.
2. Cutting incorrect material.
1. Too much tensionon
motor belt.
Remedy
1. Adjust tracking. See ASSEMBLY AND ADJUSTMENTS
section "BLADE TRACKING".
2. Replace blade.
1. Adjust 'belt tension. See ASSEMBLY AND
ADJUSTMENTS section "BLADE TENSION".
2. Stop feeding, back up the material slightly, until the
band saw speeds up.
3. Replace blade.
4. Slow down, trying to cut too fast. See "MOTOR
TROUBLESHOOTING GUIDE" on page 23.
1. Adjust tension. See ASSEMBLY AND
ADJUSTMENTS section "BLADE TENSION"
2. Use correct cutting technique.
See OPERATION section "GENERAL CUTTING".
1. Adjust upper and lower blade guides.
2. See OPERATION section "BLADE SELECTION".
1. Adjust according to ASSEMBLY AND
ADJUSTMENTS section, "INSTALL THE 'BELl"'.
MOTOR
Problem
Noisy operation.
Motor will not start.
Motor will not start and fuse
or circuit breaker opens.
Motor fails to develop
full power.
Motor Overheats.
Motor stalls or slows.
Frequent fuse or circuit
breaker failure.
Pm'obable Cause
1. Incorrect belt tension.
2. Loose motor pulley.
3. Loose pulley cover•
1. Not plugged into power
outlet.
2. Switch and keY not in ON 2,
position.
3. Motor cord cut or abraded. 3.
4, Plug on cord is faulty. 4.
5. Fuse on circuit breaks open. 5.
6. Faulty motor 6,
1. Too many electrical 1.
machines.
2. Incorrect fuse, 2.
3. Wheels do not rotate. 3.
4. Undersized extension cord. 4.
5. Short circuit. 5.
1. LoW line voltage. 1.
t
2. Fa_Jltyrnotor or capacitor. 2.
1. OVerload on motor. 1
2. Poor ventilation!of motor. 2.
Provide better air circulation.
3. Capacitor failure. 3.
1. Motor overload. _'- 1.
2. Low line voltage. 2.
3. Loose wire connections. 3.
4. Faulty motor. 4.
I. Motor overload. 1.
2. Overload of electrical circuit, 2.
3. Incorrect fuse or circuit 3.
breaker.
I Remedy
1. Adjust tension. See ASSEMBLY AND
ADJUSTMENTS section "INSTALL THE BEET".
2. Readjust and tighten motor pulley set screw.
3. Readjust and tigtlterl pulley cover rnounting
screws.
1. Plug it into the power outlet.
Insert key and turn the switch ON.
Take to Sears Service Center for new cord.
Take to Sears Sef:vice Center for new plug.
Re-set; may be too rnany rnachines on line.
Take to Sears Service Center for repair
or replacement.
Turn off other machines and try again,
Try tirne delay fuse, or go to circuit with higher
rated fuse or circuit breaker.
Unplug and turn wheels by hand, move
obstruction.
Use correct size extension cord; see page 5.
Cord, plug, or motor need repair; take to Sears
Service Center for repair.
Check power lille for proper voltage.
Take to Sears Service Center for evaluation.
• Reduce load to motor, feed work slower into blade.
Unplug and clean out around motor; provide
better air circulation•
Take to Sears Service Center for repair.
Reduce load to motor, feed work slower into blade.
Check power line for proper voltage•
Take to Sears Service Center for repair.
Take to Sears Service Center for repair.
Reduce load to motor, feed work slower into blade.
Too marly electrical appliances on same circuit.
Have electrician upgrade service to outlet.
CRAFTS_#A_ 14" ECA_D _qAW
"When servicing use only CRAF"IFSMAN replacement pads. Use of any other parts may create a HAZ_ARD or cause product damage.
- Any attempt to repair or replace electrical parts on ibis band saw may create a HAZARD unless repair is done by a qualified service
technicim_. Repair service is availabl{] at your nearest Sears Service Center.
ORDER ONLY BY MODE[_ NUMBER AND PART NUMBER
137.224240-
1'1 3AD01"101 Blade gtrar(I block 4 82 3AD08201 Hex. screw t/2x2
12 3AD01201 Tension knob 1 83 STD551031 Flatwasher 112x28
13 3AD01301 Nameplale 1 84 3AD08402 Molor
I4 3AD01401 Adjust nut 6mm 2 85 3AD08501 Key 5×5x60
16 3AD01501 Spring 1 86 3AD08601 Nut fi/16
16 3AD01602 Sliding bracket 1 87 3AD0870I Adjusl scrwe 6x45
17 3AD01701 Square nut 3/8 1 99 3ADO8802 Motor pulley 3
18 3AD01801 Adjnstmenl knob 5/16"'2" 1 89 3AD08901 Set screw w/I washer 3/16 x 3/0
19 3AD61901 Shaft hinge 1 90 3ADO90O2 Swilch
_jo__a,L,,po__O..L,.s'_js_rew ........................ 6x!.o........... 4__8_.. :L/Lq_oa__£t __.._ ......................... 5_xsx3o........ _2.....
I
I
1
1
4
2
1
2
1
21 3AD02101 Steel pin 2 92 3AD09202 V-belt • A-26 1
22 3AD02201 Upper wheel shaft 1 93 3AD09302 Switch box 1
23 3AD02301 Bearing 6202ZZ 2 94 3AD0g4Ol Set screw w/Iwasher. 3/'16x3/8 2
24 3AD02401 Upper wheel 1 95 3AD09502 Flat washer 3/16x12 2
25 3AD02501 Tire 2 96 3AD0gBOl Se(screww/I washer 3/'16x1/4 1
26 STD541050Hex. nut '1/2 1 97 3AD09701 Frame arm cover, lower 1
27 3AD02701 Stud 2 96 3AD09802 Frame arm cover, upper 1
20 3AD02801 Upper guard inside 1 99 STD541631 Nut 5/16 ' I
29 3AD02901 Upper guard outside 1 t00 3AD10001 Pin 3x10 1
_2o__35D9_2o_oj..Y!! ........................ :__x3jk.......... _______,%&b_o__ot __]_o_o!__w_a_s_h_er_................ 5___t__t......... _....
51 3ADO510I Set screww/I wasl_er 3/16x3/8 1/4x16 2
52 3AD05201 He_. nut 5116 1 123 3ADI2301 Blade guard 1
53 3AD05301 Hex. bolt 1/4x3/4 2 124 3AD12401 Clip tread 2
54 STD551025 Flat washer 114 2 125 3AD12501 Set screw 3116x1/4 2
55 3AD0550I t.ower guide support 1 126 3AD1260I hex. wrench 3ram 1
56 3AD05601 Setscrew 6x10 3 127 3AD12701 Set screw washer 3/'16x3/8 2
57 3AD05701 Hinge 2 '128 3ADI2801 Flatwasher 3/16 2
58 3AD05801 Set screw 3/16x3/8 2 129 STD551031 Flat washer 5/I6 2
59 3AD05gOl Plate 2 130 3AD13001 C-ring S-2O 1
31 3AD03101 Selpin
32 3AD03201 Hex. bolt
33 STD551075 Flat washer
34 3AD03401 Base
35 3AD03501 14ex.nut
36 3AD03601 Blade
37 3AD03701 ]able insert
39 3ADO3801 Table pin
39 3AD03902 Table
40 3ADO40Ol Special hex. bo/
41 3AD0410/ Trunnion clamp shoe
42 3AD04201 Trunnion
43 "3AD04301 Hex. screw
44 3AD0440i Hex. bolt
45 3AD04501 Trunnion suppoll brackel
46 3AD04601 Star knob
47 STD551025Spring washer
48 3AD04802 Set screw
49 3ADg4901 Hex. bolt
4 102 3AD10202 Shaft 1
3/4x2-1/2 1 " 103 3AD10301 Pointer 1
3/4 2 164 BAD10401 Scale 1
I 105 3AD10501 Nut- 5/16 4
3/4 1 106 3AD16601 Set screw w/I washer 3/16xl/4 2.
I 107 3AD10701 Copper washer • 2
1 108 3AD10801 Stud 2
1 109 3AD1090I Set screw w/I washer 3/16xl/2 2
16" x16"_ 1 110 3ADl1002 Miter gauge 1
10x50 2 111 3ADl1101 Y _£e block 2
2. '112 3ADl1201 Flatwasher 3/16x14 2
2 113 3ADl1301 Knob 1
I/4x5/8 6 1'14 3AD11401 Headless screw 5/16x5/16 1
5/16x1-1/4 2 115 3AD11501 Spring 1
u!" • _,- 1 118 3ADI '160"1 Steel ball 1/4 1
"16nrn] 2"117 3ADl170"1 Spring washer 3/16 2
5/16 6 118 3A011801 Holder, brush 1
3/16X2-1/4 2 119 3ADt 1g0"1 Spring washer 3/16 16
5/16x3" 1 126 3AD12001 Spring plate, connector 2
_30 _3AD93!02 J£nob....................... 318 ........... 2 _ I01 .,ZADj0] 0t ___..r!s..lk.................................. 3....
_50 _:3_A..Oo£oILC-ri!i"........................ S: 19.......... 2__ J!I 3ApJ_2]01__syLr-Jap- screw................ 3/-_613J!....... ]....
2 122 STD551025 Flatwasher
_rio _ #AD#§£0_I Se.t screw wlLwa sl_ej" ............ 11.16x318....... L4_ _ 131 3ApJ 3111 __ Set screw wJl washer ........... 311611/4 ....... _2 ___
61 3ADO6101 Power cord storage 2 132 3AD13201 Spring 3x20 1
62 3AD06202 Spring washer 3/16" 16 133 3AD1330I Spring washer 3/4 1
63 3AD06302 Pulley 7" 1 134 3AD13401 Set screw 3/16x3/8 1 ,
64 3AD06401 14ex. screw 5/16xlt/4" 4 135 3AD1350I Set screww/I washer 4
65 3AD06501 Snap ring R-34 2 136 3AD13601 Hinge 1
66 3ADO660I Bearing 6204ZZ 2 137 3AD13701 Spring washer 3/4" 1
67 3ADO8701 Lower wheel 1 138 3AD1380I 14ex. nut 3/4!! 1
69, 3AD06801 Hex. screw 114x5/8 1 139 3A013901 Flatwashef 3/8x25 1
60 3AD06901 Lower door 1 140 3AD14001 Handle 1
70 3ADO7001 Guard 1 14I 3AD14101 Pointer 1
71 3AD67162 Bearing cover 1 142 3ADI420I Flat washer 3116 2
143 3AD14301 Set Screw MBx16L 1
Kej! Part No. Descriplion Qly Key Part No. Description QIy
1 3AD001gl Upper frame mm 1 72 3AD07202 Set screw 3116x3/8 6
2 3ADO()201 Lock handle 6/I6x1-1/4 1 73 3AD07301 Flatwasher f/16x23 2
!
3 3AD00301 Nut 3/'16 12 74 3AD07401 Plate 1
4 3AD00401 Guide post '1 75 3AD07501 ' Cord, motor 1
5 3ADOO501 Guide supporl bracket .. 1 76 3AD07601 Stain relief bushing 2
6 3AD00601 Sector screw 6xl0L 1 77 3AD07701 Power cord & plug 1
7 3AD00701 Upper spacing sleeve 2 70 STD551031 Flatwasher 5/-16xl8 8
8 3AD()0801 Blade goard 1 79 3ADO7901 Flex, screw 1/4x1/4 2
g 3AD0OgOl Bearing 6200ZZ 2 60 3ADOSOOl Dust chute 1
:: ?
J
{;i
< ::1
?i
on
1
I
58
112
103
_55
/
,t:_j
7O
~-
39
/
8O
€,a
b
©
C _AIFTSI_IAIT\_ _AND SAW LE(_ STA_D _3L22424
When servicing .use 0nly CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause
product damage.
Any attempt to repair or rep ace electrical paris on _,hisband saw may create a HAZARD unless repair is done by a
qualified service technician. ReP.air service is available at y6ur nearest Sears Service Center.
1 .-IAD30102 Top Plate 1
2 1AD30202 Tools Tray 1
3 1AD30302 L.H. Side Plate 1
4 1AD30402 R,H. Side Plate 1
5 1AD30502 Back Plate 1
6 1AD30602 Door Plate 1
7'1AD30702 Magnetic Iron Set 2
8 1AD30802 Tapping Screw 3 xl 2 4
g 1AD30902 Set Screw wNVasher 3/16"x3/8" 8
10 1AD31002 Carriage Screw 5/16"xl/2" 16
11 tAD31102 Hex Nutlw/Washer 5/16" 16
12 1AD31202 Hex. Nut 3/8 4
13 1AD31302 Pad 4
14 1AD31402 Hex, Screw 1
15 1AD31502 Spring VTasher 1
16 1AD31602 Knob "1
17 IAD3'1702 Label 1
CRAFTS_'_b_N BAil[i) SAW L[::Q STAili] =Q=o_=- °.=o-=.,_',_,
b
I-I J

Navigation menu