Craftsman 137248880 User Manual TABLE SAW Manuals And Guides L0706477

CRAFTSMAN Saw Table Manual L0706477 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

User Manual: Craftsman 137248880 137248880 CRAFTSMAN TABLE SAW - Manuals and Guides View the owners manual for your CRAFTSMAN TABLE SAW #137248880. Home:Tool Parts:Craftsman Parts:Craftsman TABLE SAW Manual

Open the PDF directly: View PDF .
Page Count: 30

Download
Open PDF In Browser	View PDF

Operator's Manual

gN ,®
3.0 HP (Max. Developed)
10" Inch Blade
5000 R.P.M.

TABLE SAW
Model No.
137.248880

CAUTION:

•
•
•
•
•

Before using this Table Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions

Safety Instructions
Installation
Operation
Maintenance
Parts List

Customer
Help Line
1-800-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www.sears.com/craftsman

Part No. 13724888001

SECTION

PAGE

Warranty ........................................
Product Specifications .......................
Power Tool Safety ............................
Table Saw Safety ..............................
Electrical Requirements and Safety ......
Accessories and Attachments ..............
Tools Needed For Assembly ................
Carton Contents ..............................

2
2
3
4
5
6
6
6

SECTION

PAGE

Know Your Table Saw .......................
Assembly and Adjustments .................
Operation .......................................
Maintenance ...................................
Troubleshooting Guide .......................
Parts List ........................................
Push Stick Pattern ...........................

8
9
16
20
21
22
30

FULL ONE YEAR WARRANTY
If this Table Saw fails due to a defect in material or workmanship
Sears will at its option repair or replace it free of charge.

within one year of date of purchase,

Return this Table Saw to a Sears Service Center for repair, or to place of purchase for replacement.
This warranty gives you specific legal rights, and you may also have other rights which may vary from
state to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffman Estates, IL 60179

1_ WARNING I
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
° Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals work in a well-ventilated area and work with approved safety equipmentsuch
as
dust masks that are spec a y des gned to f ter out m croscop c part c es.

MOTOR
HP (Maximum developed) .....
Type ..................................
Amps .................................
Voltage ..............................
Hz ......................................
RPM (no load) ....................
Overload Protection .............

[A WARNING I

3.0
Universal
15
120
60
5000
YES

SAW
Table Size ........................
Table Extensions ...............
Extension Fence Capacity...
Blade Size ........................
Rip Scale .........................
Rip Fence ........................
Miter Gauge ......................
Maximum Cut Depth @ 90°..
Maximum Cut Depth @ 45°..
Maximum Dado Cut Width...
Net Weight ......................

26-7/64" x 19-1/2"
Yes, with fences
24" Right and Left
10"
YES
YES
YES
3"
2-1/2"
1/2"
64.5 LBS

To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.
This table saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15
Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn,
cut or damaged in any way.
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow
these rules could result in serious injury to you or damage to the table saw.

I_ WARNING]
Before using your table saw, it is critical that you read and understand these safety rules.
Failure to follow these rules could result in serious injury or damage to the table saw.
Good safety practices are a combination of common
sense, staying alert and understanding how to use your
power tool. To avoid mistakes that could cause serious
injury, do not plug in your power tool until you have read
and understood the following safety rules:
1.

READ and become familiar with this entire
Operator's Manual. LEARN the tool's applications,
limitations and possible hazards.

2. [A, WARNING I

15 REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning ON.
16 NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER "OFF". Do not leave the tool
before it comes to a complete stop.
17 NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.

Look for this symbol that identifies important
safety precautions. It means CAUTION!
BECOME ALERT! YOUR SAFETY IS INVOLVED!

18 DO NOT OVERREACH. Keep proper footing and
balance at all times.

NEVER OPERATE THIS MACHINE WITHOUT THE
SAFETY GUARD IN PLACE FOR ALL THROUGH
SAWING OPERATIONS.

19. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for most efficient and safest performance.
Follow instructions for lubricating and changing
accessories.

DO NOT USE IN A DANGEROUS ENVIRONMENT
such as damp or wet locations or exposure to rain.
Keep work area well lighted.
DO NOT use power tools in the presence of
flammable liquids or gases.

KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.

KEEP CHILDREN AWAY. All visitors should be kept
at a safe distance from the work area.

DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.

USE THE RIGHT TOOL. Don't force the tool or
attachment to do a job for which it is not designed.

20. CHECK FOR DAMAGED OR LOOSE PARTS.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
ensure it will operate properly and perform its
intended function. Check for alignment of moving
parts, binding of moving parts, loose mounting and
any other conditions that may affect its safe
operation. A guard or other part that is loose or
damaged should be properly adjusted repaired or
replaced.
21. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
22. DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could impair your ability to use the tool safely.

10. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry that may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair
covering to contain long hair.

23. USE DUST COLLECTION SYSTEM wherever
possible. Dust generated from certain materials can
be hazardous to your health and in some cases, a
fire hazard. Always operate the power tool in a wellventilated area with adequate dust removal.

11. WEAR A FACE MASK OR DUST MASK. Sawing,
cutting and sanding operations produce dust.

24. ALWAYS WEAR EYE PROTECTION. Any power
tool can throw foreign objects into your eyes that
could cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with ANSI
safety standard Z87.1. Everyday glasses have only
impact resistant lenses. They ARE NOT safety
glasses.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could cause serious injury when they
break.

12. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, cutters, etc.
13. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure the switch is in the OFF
position before plugging into the power supply.
14. USE ONLY RECOMMENDED ACCESSORIES.
Consult the Operator's Manual for recommended
accessories. The use of improper accessories may
cause injury to you or damage to the tool.

25. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.

ALWAYS USE SAW BLADE GUARD, splitter and
anti-kickback pawls for every operation for which they
can be used, including through sawing. Through
sawing operations are those in which the blade cuts
completely through the workpiece when ripping or
crosscutting.
ALWAYS HOLD WORK FIRMLY against the miter
gauge or rip fence.
USE A PUSH STICK when required. Always use a
push stick especially when ripping narrow stock.
Refer to ripping instructions in this Operator's Manual
where the push stick is covered in detail. A pattern for
making your own push stick is included on page 30.
NEVER PERFORM ANY OPERATION FREE HAND,
which means using only your hands to support or
guide the workpiece. Always use either the fence
or the miter gauge to position and guide the work.
WARNING: FREEHAND CUTTING IS THE MAJOR
CAUSE OF KICK-BACK & FINGER/HAND
AMPUTATIONS.

NEVER STAND or have any part of your body in line
with the path of the saw blade. Keep your hands out
of the saw blade path.

NEVER REACH behind or over the cutting tool for
any reason.

REMOVE the rip fence when crosscutting.

DO NOT USE a molding head with this saw.

FEED WORK INTO THE BLADE against the
direction of rotation only.

10. NEVER use the rip fence as a cut-off gauge when
crosscutting.
11. NEVER ATTEMPT TO FREE A STALLED SAW
BLADE without first turning the saw OFF. Turn power
switch OFF immediately to prevent motor damage.

12. PROVIDE ADEQUATE SUPPORT to the rear and
the sides of the saw table for long or wide workpieces.
13. AVOID KICKBACKS (work thrown back towards you)
by keeping the blade sharp, the rip fence parallel to
the saw blade and by keeping the splitter, antikickback pawls and guards in place, aligned and
functioning. Do not release work before it has passed
all the way past the saw blade. Do not rip work that is
twisted, warped or does not have a straight edge to
guide it along the fence.
14. AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause your hand
to move into the saw blade.
15. NEVER USE SOLVENTS to clean plastic parts.
Solvents could possibly dissolve or otherwise
damage the material. Only a soft damp cloth should
be used to clean plastic parts.
16. MOUNT your table saw on a bench or stand before
performing any cutting operations. Refer to
ASSEMBLY AND ADJUSTMENTS on page 9.
17. NEVER CUT METALS or materials which may make
hazardous dust.
18. ALWAYS USE IN WELL-VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust from
the interior of the saw to prevent a potential fire
hazard. Attach a vacuum to the dust port for
additional sawdust removal.
19. NEVER LEAVE THE SAW RUNNING
UNATTENDED. Do not leave the saw until it comes
to a complete stop.
20. For proper operation follow the instructions in this
Operator's Manual entitled ASSEMBLY AND
ADJUSTMENTS (Page 9). Failure to provide
sawdust fall-through and removal hole will allow
sawdust to build up in the motor area resulting in a
fire hazard and potential motor damage.

POWER

SUPPLY

REQUIREMENTS

I
A WARNING]
To avoidelectrical
hazards,fire
hazardsor damage tothe
tablesaw, use propercircuit
protection.
Always use a
separate electrical circuit for your tools. This power tool is
wired at the factory for 120V operation. Connect it to a
120V, 15 Amp circuit and use a 15 Amp time delay fuse
or circuit breaker. To avoid shock or fire, replace the cord
immediately if it is worn, cut or damaged in any way.

EXTENSION

CORD REQUIREMENTS

I
n WARNING]
Any extension cord must be GROUNDED for safe
operation.
MINIMUM GAUGE FOR EXTENSION CORDS
(AWG type / 120 Volt only)
Ampere Rating
Total length in feet
Not
More Than
More Than
25'
50'
100'
150'
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
_1
_12:

GUIDELINES

FOR EXTENSION

CORDS

Any extension cord used for power tools MUST be
grounded (3-wire with two flat prongs and one round
ground prong).

GROUNDING

INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provides a path of least
resistance for electric current and reduces the risk of
electric shock. This saw is equipped with an electric cord
that has an equipment grounding conductor and a
grounding plug. The plug MUST be plugged into a
matching receptacle that is properly installed and
grounded in accordance with ALL local codes and
ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit
the receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor (wire) with the green insulation (with or without
yellow stripes) is the equipment grounding conductor. If
repair or replacement of the electric cord or plug is
necessary, DO NOT connect the equipment grounding
conductor to a live terminal.
CHECK with a qualified electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the saw is properly
grounded.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole grounding receptacles that
accept the saw's plug. Repair or replace damaged or
worn cords immediately.

Make sure the extension cord is in good condition. When
using an extension cord, make sure you use one heavy
enough to carry the current the tool will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table above shows
the correct size to use according to extension cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge cord. The smaller the gauge number the
heavier the cord.
NOTE: The 12 to 16 Amp rating is correct for this tool. It
is highlighted in the table above.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Before connecting the saw to the extension cord, make
sure the saw switch is turned OFF.

3_P_r_l

_,t_/

.Jbr_

Plug

Make Sure This

II is Conr,
ec_ed
toa
Known Ground
2-Prong

Ad_pt_--:._ Receptacle

RECOMMENDED

ACCESSORIES

[_ WARNING I
Visit your Sears Hardware Department or see the
Craftsman Power and Hand Tools Catalog to purchase
recommended accessories for this power tool.

[,&, WARNINGI
To avoid the risk of personal injury:
• Do not use adjustable (wobble) type dadoes or
carbide tipped dado blades; maximum dado width is
1/2".
• Do not use a dado with a diameter larger than 6".
• Do not use molding head set with this saw.
• Do not modify this power tool or use accessories not
recommended by Sears.

TOOLS

M_ium

screwdriver
Adiustab/e wrench

#2 Philtips screwdrive_

Combination

square

AND CHECKING

CONTENTS

Separate all parts from packing materials. Check each
part with the illustration on the next page and the "Table
of Loose Parts" to make certain all items are accounted
for, before discarding any packing material.

IA_,WARNING]
Ifany partismissingor damaged, do notattemptto
assemblethetablesaw, pluginthepower cord,or turn
theswitchON until
themissingordamaged partis
obtainedand isinstalled
correctly.

TABLE OF LOOSE PARTS
ITEM
A.
B.
C.
D.
E.
F.
G.

NEEDED

Straigh_ edge

UNPACKING

DESCRIPTION
QUANTITY
Table saw assembly
1
Table extension
2
Rear table extension
1
Rear table extension tube
2
Location seat
5
Blade guard and splitter
1
Bolt, flat washer, toothed washer,
1 each
Oval washer, spring washer
Rip fence
1
Hand wheels
2
Dome nuts
2
Dado table insert
1
Miter gauge
1
Hex keys
2
Blade wrenches
2
Dust chute
1
Dust bag
1
Blade
1

H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.

STAN D:
R.
S.
T.
U.
V.
W-1.
W-2.

NOTE:

Top short leg bracket
Top long leg bracket
Bottom short bracket
Bottom long bracket
Legs
Bag of bolts, nuts, pads,
flat washers
Bag of hooks, bolts, nuts,
Parallel washers

To make assembly

easier,

keep contents

2
2
2
2
4
1 each
1 eanh

of box

together. Apply a coat of automobile
wax to the table. Wipe all
parts thoroughly with a clean dry cloth. This will reduce friction
when pushing the workpiece.

UNPACKING

YOUR TABLE SAW

B
Q

0
P

W-1

W-2

Table
Blade Guard

Insert
Rip Fence
SideTable
Extension

Table lock
handles

Blade Tilting
Handwheel

Blade tilt pointer
Overload
switch
Blade

ON/OFF

reset

Blade bevel
lock knob

tilt scale

Blade elevation
handwheel

switch

with key

Fence storage

Miter Gauge
Table

Rear Table
Extension
Mounting

Dust Ba¢l

Stand

holes

Assemble stand (Fig. A)
Unpack all parts and group by type and size (Fig. A).
Refer to parts list for c uantities.
2. Attach one long upper support (11, 17) to top of leg (t)
using one square neck bolt (2) and nut (8).
NOTE: Do not tighten bolts until stand is properly aligned
(see step #9).
. Attach other end of long upper support to top of another
leg using one square neck bolt and nut.
4. Attach one long bottom support (3) to center of each leg
using square neck bolts and nuts. This completes the
front frame section.
. Assemble
rear frame section in exactly the same way.
6. Join front and rear frame assemblies using two short
upper supports (9) and two short bottom supports (t3),
square neck bolts and nuts.
, Insert large hex head bolt (4) into leg spacer (5) and
insert into bottom of leg. Fasten with washer (6) and nut
(7). Repeat for each leg.
, Attach the hooks (14) to the frame as desired. The hooks
are used to hold the fence, the blade wrenches and miter
gauge.
g,
Place stand on level surface and adjust so all legs are
contacting the floor and are at similar angles to the floor.
Tighten all bolts.
NOTE: Stand should not rock after all bolts are tightened.
,

Assemble table saw to stand (Fig. A, B)
1.
2.
3.

4.
5.
6.

Place protective corrugated cardboard or old
blanket on floor to protect the saw table surface.
Place the saw up-side down on the protective
material (Fig. B).
Position the stand up-side down on the saw base.
NOTE: Make sure front of stand (identified with
Craftsman label) and front of saw are facing the
same direction.
Position the dust chute between the stand and saw.
Line up four holes in saw base, dust chute and
stand.
Fasten saw to dust chute and stand using four bolts
(10), washers (11) and nuts (8).
NOTE: Place washer on each bolt before inserting
into saw base and through the support. Nut must
be flush against the bracket (see Fig. A).
Tighten all four nuts.
NOTE: DO NOT OVER TIGHTEN NUTS HOLDING
SAW TO STAND. THIS WILL DAMAGE THE SAW
BASE.
Carefully set the saw in its upright position on a
clean level surface.

Fig. B

Fig. A

/
/
1

SAW MOUNTED TO WORK SURFACE (FIG. C)
1. If the leg set will not be used, the saw must be
properly secured to a sturdy workbench using the
four mounting holes at the base of the saw.
2. The surface of the table where the saw is to be
mounted must have a hole large enough to facilitate
sawdust fall-through and removal.
3. Square the saw on the mounting surface and mark
the location of the four 3/8" mounting holes (1).
4. Drill 3/8" hole into the mounting surface.
5. Mark an 11" square (2) centered between the four
mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to fall through the
saw base.
8. Place the saw on the work surface, and align the
mounting holes of the saw with those drilled through
the surface.
9. Fasten the saw to the work surface.

Place the dust bag neck opening around the dust chute
and tie the dust bag with string.

Fig. D

14WARNING]

Do notoperatethismachine on thefloor.
Thisisvery
dangerousand may cause seriousinjury.

Fig,C

•

#
i¸

BLADE RAISING HANDWHEEL (FIG. E, F)
1. Attach the handwheel (1) to the elevation screw (2)
at the front of the saw.
Make sure the slots (3) in the hub of the
handwheel engage with the pins (4). (Fig. E)
2. Attach and tighten the dome nut (5) at the end of the
shaft (Fig. F).

Fig. E

.
IAWARNING]
Failure
toprovidethesawdustfall-through
holewill
cause sawdustto buildup inthemotorarea,which may
result
infire
or cause motordamage.
KEEPING THE AREA CLEAN (FIG. D)
1. Sawdust and wood chips that fall from under the saw
will accumulate on the floor.
2. Make it a practice to pick up and discard this dust
when you have completed cutting.

14WARNING]
Always keep yourwork area clean,uncluttered
and well
lit.
I. Ifthedustbag isnotused,do notwork on floor
surfacesthatareslippery
fromsawdustor wax.
2. When usingthedustbag some dustwill
notfall
into
thebag butcome outthroughopeningsinthe
housing.Do notcoverthemotorcooling
vents.
INSTALLING THE DUST BAG (FIG. D)

14WARNING]

Do not use this saw to cut and sand metal. The hot
chips or sparks may ignite sawdust or the bag material.

BLADE TILTING HANDWHEEL (FIG. G, F)
1. Attach the other handwheel (6) to the blade tilting
screw on the side of the saw in the same manner as
above.
2. Attach and tighten the handwheel dome nut (5).

Fig. F

RIP FENCE (Fig. G)
1. Lift upward on the rip fence handle (1) so that the
holding clamp (2) is fully extended.
2. Place the rip fence on the saw table and engage
the holding clamp (2) to the table rear. Lower the
front end onto the front rail (3).
4. Push down on the fence handle (1) to lock.

2. Raise the blade arbor (4) (Fig. I) to the maximum
height by turning the blade raising handwheel
counterclockwise.
3. Remove the arbor nut (5) and flange (6), remove
blade.
4. Install the saw blade onto the arbor with the blade
teeth pointing toward the front of the saw.
5. Install the flange (6) against the blade and thread the
arbor nut (5) as far as possible by hand. Ensure that
the blade is flush against the inner side of the blade
flange.

Fig. G
2

[A WARNING I
To avoid possible injury and damage to the workpiece
be sure to install the blade with the teeth pointing
toward the front of table in the direction of the rotation
arrow on the blade guard.

Fig. I
5

INSTALLING AND CHANGING THE BLADE
(FIG. H, I, J)
IdYlLWARNING
•

•

]

To avoid injury from an accidental start, make sure
the switch is in the OFF position and the plug is
not connected to the power source outlet.
To avoid serious injury, table insert must be level
with the table. If the table insert is not level with the
table, adjust the screw (3) until it is level with the
table. To raise the insert, turn the screw
counterclockwise, to lower the insert, turn the
screw clockwise.

6. To tighten the arbor nut (5) place the open-end
wrench jaws on the flats of the saw arbor to keep the
arbor from turning. (Fig. J)
7. Place the box-end wrench (8) on the arbor nut (5),
and turn clockwise (to the rear of the saw table).
8. Replace the blade insert in the table recess, insert
the screws through the front and rear holes and
tighten.

1. Remove the table insert (t) by unscrewing the two
screws (2, 3).Be careful not to lose the rubber washer
that is on the back screw (3) beneath the table insert.
(Fig. H)

Fig. J

Fig. H

WARNING]
To avoid injuryfrom a thrown workpiece, blade parts,or
.....

blade contact,never operate saw withoutthe proper insert

inplace. Use the saw blade insertwhen sawing. Use the
dado head insertwhen

]]

using a dado.

WARNING I

BLADE GUARD ASSEMBLY (FIG. K, L, M)
1. Set the blade to maximum height and the tilt to
zero degrees on the bevel scale with the hand
wheels. Lock the blade lock knob.
2. Place the external toothed lock washer (1), a steel
flat washer (2) and a spring washer (10) onto the
long hex head bolt (3). Insert the bolt into the
splitter bracket (4) as shown. (Fig. K)

Improper splitter alignment can cause
"kickback" and serious injury.

Fig. K

Fig. M
3
1
10 3
Place the oval washer (5) on the pivot rod (6). (Fig.
L)
3. Install the bracket assembly (4) at the rear of the
saw table and snugly - do not tighten. Thread the
bolt (3) into the internally threaded pivot rod.

INSTALLING TABLE SIDE EXTENSIONS (FIG. N)
1.

NOTE: The splitter is removed from the illustration
for clarity.
2.

Fig. L

Identify the right hand table extension.
NOTES:
For illustration purposes the view in Fig. N looks
"through" the saw table to the under side of the
table.
The right hand table extension is the one with
the measuring scale (1) visible from the front of
the saw when it is installed to the right hand side
of the saw table (Fig. N).
Open both front and rear cam locking levers (2)
on the right hand side of the saw base by pulling
them out from the cam locking assemblies (4).
Insert the table extension mounting tubes (3)
into the two matching holes in the cam lever
assemblies.
NOTE: Make sure the front mounting tube has
the measuring scale visible from the front of the
saw.

4.
6

Slide the table extension toward the table until it
rests against the saw table.
Lock both cam locking levers by pushing them in
toward the cam locking lever assemblies.

4. Position the blade guard arm (7) to the rear of the
table. (Fig. M)
5. Using a straight edge, check to see if the blade
guard splitter (8) is aligned with the saw blade (9).
6. If straightening adjustment is necessary, loosen
the bolt (3) and shift the splitter assembly to right
or left, or rotate.
7. When the splitter is properly aligned with the saw
blade, tighten the bolt, very tight.
8. If height adjustment is necessary, loosen the knob
(11 ) and raise the splitter assembly to the desired
height and tighten the knob. (Fig. K)
NOTE: The splitter must always be correctly
aligned so that the cut workpiece will pass on
either side without binding or twisting to the side,

Fig. N

INSTALLING TABLE SIDE EXTENSIONS- cont'd

ADJUSTING REAR TABLE EXTENSION

(FIG. O)
6. Snap one location seat (5) over the end of the rear
table extension tube (3). Make sure the locating pin
(6) in the location seat fits into the matching hole in
the extension tube (Fig. O).
7. Install the left hand table extension in a similar way.
NOTE: Install location seat on front table extension tube.

1. Rear table extension should be positioned as close

NOTE:
For illustration purposes the view in Fig. O looks
"through" the saw table to the under side of the table.

RIP FENCE ADJUSTMENT

is parallel with the miter gauge groove.
• Tighten both screws and push the handle to lock.
5. If fence is loose when the handle is in the locked
(downward) position, do the following:
• Move the handle (2) upward and turn the adjusting
nut (5) clockwise until the rear clamp is snug. Do not
turn the adjusting screw more than 1/4 turn at a
time.
• Over-tightening the adjusting screw will cause the
fence to come out of alignment.

INSTALLING REAR TABLE EXTENSION (FIG. P)
1. Place the rear table extension onto the two rear table
extension tubes (1).
2. Snap two location seats (4) over the two rear table
extension tubes (1).Make sure the locating pin in the
location seat fits into the matching hole (5) in the
extension tube.

(FIG. Q)

1. The fence (1) is moved by lifting up on the handle (2)
and sliding the fence to the desired location. Pushing
down on the handle locks the fence in position.
2. Position the fence on the right side of the table, and
along one edge of the miter gauge grooves.
3. Lock the fence handle. The fence should be parallel
with the miter gauge groove.
4. If adjustment is needed to make the fence parallel to
the groove, do the following:
• Loosen the two screws (3) and lift up on the handle
(2).
• Hold the fence bracket (4) firmly against the front of
the saw table. Move the far end of the fence until it

Fig. 0

as possible to the rear of the table when ripping
short work pieces.
Rear table extension should be pulled out fully until
the location seat prevents it from moving outward
when ripping long work pieces that require extra
support as you are completing the cut.

Insert rear table extension tubes (1) into the two
holes in the rear of the saw table (3) and into
extension tube brackets under the table.
Position rear table support so instruction labels
are up.
Snap one location seat (4) over the end of the left
rear table extension tube (1). Make sure the
locating pin in the location seat fits into the
matching hole in the extension tube.

IA WARNING
I
Failure to properly align fence can cause "kickback" and
serious injury.

Fig. Q

Fig. P

4
]3

RIP FENCE INDICATOR ADJUSTMENT (FIG. Q)
1. The rip fence indicator (6) points to the
measurement scale (8). The scale shows the
distance from the side of the fence to nearest side
of the blade.
2. Measure the actual distance with a rule. If there is
a difference between the measurement and the
indicator, adjust the indicator (6).
3. Loosen the screw (7) and slide the indicator to the
correct measurement on the scale. Tighten the
screw and remeasure with the rule.

Fig. Q-2
90 °

45 °

IA WARNING
I

...................

To avoid injury from an accidental start, make sure
the switch is in the OFF position and the plug is not
connected to the power source outlet.
ADJUSTING THE 90 ° AND 45" POSITIVE STOPS
(FIG.Q-I, Q-2, Q-3)
Your saw has positive stops that will quickly position
the saw blade at 90 ° to the table. Make adjustments
only if necessary.
90 ° Stop
1. Disconnect the saw from the power source.
2. Turn the blade elevation handwheel and raise
the blade to the maximum elevation.
3. Loosen the blade bevel lock handle (2) and
move the blade to the maximum vertical position.
Tighten the lock handle (2).
4. Place a combination square on the table and
against the blade (t)to determine if the blade is
90 ° to the table. (Fig. Q-2)
5. If the blade is not 90 ° to the table, loosen the two
set screws (4), located on the bottom of the table
saw, (Fig. Q-3) with the hex key, and back off
the collar..
6. Loosen the bevel lock knob. Turn the blade
tilting handwheel to move the blade until it is 90 °
to the table.
7. Adjust the collar (5) so it contacts the bracket (3)
when the blade is 90 ° to the table. Tighten the
two set screws (4).

45 ° Stop
1. With the blade in the upright 90 ° position, loosen
the bevel lock knob and move the blade to the
45 ° position as far as it will go.
2. Place the combination square on the table as
shown in (Fig.Q-2) to check if the blade is 45 ° to
the table.
3. If the blade is not 45 ° to the table, adjust the
screw (4) (Fig. Q-3) with a screw driver until the
blade is 45° to the table.
4. Tighten the bevel lock handle.
5. Tighten the screw (4) until resistance is felt. Do
not overtighten.
BLADE TILT POINTER
1. When the blade is positioned at 90 °, adjust the
blade tilt pointer to read 0° on the scale.
2. Loosen the holding screw, position pointer over 0 °
and tighten the screw.
NOTE: Make a trial cut on scrap wood before
making critical cuts. Measure for exactness.

Fig. Q-3

Fig. Q-1

345

BLADE PARALLEL TO THE MITER GAUGE
GROOVE (FIG. R,S)

I_WARNING
I
This adjustment was made at the factory, but it
should be rechecked and adjusted if necessary.

IAWARNING
I
To preventpersonalinjury:
• Always disconnect
plugfromthepower source
when making any adjustments.
•
This adjustment must be correct or kickback
could result in a serious injury and accurate cuts
can not be made.
1. Remove the yellow switch key and unplug the saw.
2. Move the blade guard out of the way.
3. Raise the blade to the highest position and set at
the 0 ° angle (90 ° straight up).
4. Select and mark, with a felt tip marker, a blade
tooth having a "right set".
5. Place the combination square base (1) into the
right side miter gauge groove (2). (Fig. R)
6. Adjust the rule so it touches the front marked tooth
and lock ruler so it holds its position in the square
assembly.
7. Rotate the blade bringing the marked tooth to the
rear and about 1/2 inch above the blade.
8. Carefully slide the combination square to the rear
until the ruler touches the marked tooth.
9. If the ruler touches the marked tooth at the front
and rear position, no adjustment is needed at this
time. If not, perform adjustment procedure
described in next section.

Fig. R

Additional blade adjustments (Fig. S)
The adjusting mechanism is located on top of blade
height adjusting hand wheel under the tabletop. If
the front and rear measurements are not the same,
adjust the alignment by the mechanism as follows:
If the blade is partial to right side:
1. Loosen the two nuts (1) and the right side screw,
then adjust the left side screw.
2. Tighten the nuts (1) and the right screw and
remeasure, as described in steps 4 to 9 in the
prior section.
If the blade is partial to left side:
3. Loosen the two nuts (1) and the left side screw,
then adjust the right screw.
4. Tighten the nuts (1) and the left screw and
remeasure, as described in steps 4 to 9 in the
prior section.
5. Recheck blade clearance making sure that the
blade does not hit the table insert or other parts
when at the 90 ° and 45 ° settings.

Fig. S
f_

BASIC

SAW OPERATIONS

RAISE THE BLADE (FIG. T)
To raise or lower the blade, turn the blade elevation
handwheel (1) to the desired blade height, and then
tighten lock handle (2) to maintain the desired blade
angle.

OVERLOAD PROTECTION (FIG. U)
This saw has an overload relay button (3) that resets
the motor after it shuts off due to overloading or low
voltage. If the motor stops during operation, turn the
ON / OFF switch to the OFF position. Wait about five
minutes for the motor to cool. Push in on the reset
button (3) and turn the switch to the ON position.

l_k WARNING]

Fig. T

TILTING THE BLADE (FIG. T)
1. To tilt the saw blade for bevel cutting, loosen the
lock knob (2) and turn the tilting handwheel (3).
2. Tighten the lock knobs (2) to secure.
ON/OFF SWITCH (FIG. U)
The ON / OFF switch has a removal key. With the
key removed from the switch, unauthorized and
hazardous use by children and others is minimized.

To avoid injury, the ON / OFF switch should be in the
OFF position and the plug removed from the power
source while the cool down takes place, to prevent
accidental starting when the reset button is pushed.
Overheating may be caused by misaligned parts or a
dull blade. Inspect your saw for proper setup before
using it again.
USING THE TABLE EXTENSION (FIG. V, V-l)
If the table extension is not parallel with the table.
Remove the bolts (1) and position the parallel
washers (2) between the table extension and tube
until it is parallel with the table, then tighten the bolts.
NOTE: Paeallel washer (2) see page 6 for table of
loose parts ITEM: W-2

Fig. V

1. To turn the saw ON, insert key (1) into the slot in
the switch (2). Move the switch upward to the ON
position.
2. To turn the saw OFF, move the switch downward.
3. To lock the switch in the OFF position, grasp the
end (or yellow part) of the switch toggle (1), and
pull it out.
4. With the switch key removed, the switch will not
operate.
5. If the switch key is removed while the saw is
running, it can be turned OFF but cannot be
restarted without inserting the switch key (1).

NOTE: Move and lock the fence to the 15" left or
right side scale. The fence is now clear of the table.

Fig. U

1.
2.

Release the extension lock handles.
Slide the extension out until the correct
measurement is displayed on the tube scale.
The user sights the scale off the edge of the
table.
Tighten all extension lock handles.

Fig. V-1

CUTTING OPERATIONS
There are two basic types of cuts: ripping and
crosscutting. Ripping is cutting along the length and
the grain of the workpiece. Crosscutting is cutting
either across the width or across the grain of the
workpiece. Neither ripping nor crosscutting may be
done safely freehand. Ripping requires the use of the
rip fence, and crosscutting requires the miter gauge.

Fig. W

WARNINGJ

Before using the saw each and every time, check
the following:
1. Blade is tight on the arbor.
2. Bevel angle lock knob is tight.
3. If ripping, fence knob is tight and fence is
parallel to the miter gauge grooves.
4. Blade guard is in place and working properly.
5. Safety glasses are being worn.
The failure to adhere to these common safety rules,
and those printed in the front of this manual, can
greatly increase the likelihood of injury.

RIPPING (FIG. W, X)

WARNING
I
To prevent serious injury:
• Never use the miter gauge when ripping.
• Never use more than one rip fence during a single
cut.
• Do not allow familiarity or frequent use of your table
saw to cause careless mistakes. Remember that
even a careless fraction of a second is enough to
cause a severe injury.
• Keep both hands away from the blade and path of
the blade.
• The workpiece must have a straight edge against
the fence and must not be warped, twisted, or
bowed.

NOTE: When width or rop is 2" to 6" wide use the push
stick to feed the work. When width of rop is narrower
than 2" the push stick cannot be used because the
guard will interfere... Use the auxiliary fence as page
19.
6. Keep your thumbs off the table top. When both of
your thumbs touch the front edge of the table (2),
finish the cut with a push stick. Make a push stick
using the pattern on page 30.
7. The push stick (3) should always be used when the
ripped workpiece is 2" to 6" wide. (Fig. X)
8. Continue pushing the workpiece with the push stick
(3) until it passes the blade guard and clears the rear
of the table.
9. Never pull the piece back when the blade is turning.
Turn the switch OFF. When the blade completely
stops raise the anti-kickback pawls on each side of
the splitter and slide the workpiece out.

Fig. X

1. Remove the miter gauge. Secure the rip fence to the
table.
2. Raise the blade so it is about 1/8" higher than the
top of the workpiece.
3. Place the workpiece flat on the table and against the
fence. Keep the workpiece about 1" away from the
blade.
4. Turn the saw ON and wait for the blade to come up
to speed.
5. Slowly feed the workpiece into the blade by pushing
forward only on the workpiece section (t) that will
pass between the blade and the fence. (Fig. W)
2

[,_, WARNING]
AVOID KICKBACK by pushingforwardon thesection
oftheworkpiecethatpasses between thebladeand
thefence.

BEVEL RIPPING
This cut is the same as ripping except the blade bevel
angle is set to an angle other than "0".

Fig. Y
3

WARNING
I
Cutonlywiththeworkpieceand thefenceon theright
sideoftheblade.
RIPPING SMALL PIECES

I_WARNING
I
Avoid injury
fromthebladecontact.
Never make
throughsaw cutsnarrowerthan I/2"wide.
1. It is unsafe to rip small pieces. Instead, rip a larger
piece to obtain the size of the desired piece.
2. When a small width is to be ripped and your hand
cannot be safely put between the blade and the
rip fence, use one or more push sticks to move the
workpiece.

Fig. Y-1

CROSSCUTTING (FIG. Y)

WARNING
I
To preventseriousinjury:
• Do notallowfamiliarity
orfrequentuse ofyourtable
saw tocause carelessmistakes.
Remember that
even a careless
fraction
ofa second isenough to
cause a severe injury.
• Keep both hands away from the blade and the path
of the blade.

BEVEL CROSSCUTTING (FIG. Z)
This cutting operation is the same as crosscutting
except the blade is at bevel angle other than 0°.
1. Adjust the blade (1) to the desired angle, and
tighten the blade bevel lock knob.

Fig.
1. Remove the rip fence and place the miter gauge in
the left side groove.
2. Adjust the blade height so it is 1/8" higher than the
top of the workpiece.
3. Hold the workpiece firmly against the miter gauge
with the blade path in line with the desired cut
location. Move the workpiece to one inch distance
from the blade.
4. Start the saw and wait for the blade (t) to come up to
full speed.
5. Keep the workpiece (2) against the face of the miter
gauge (3) and flat against the face of the gauge and
flat against the table. Then slowly push the workpiece
through the blade. (Fig. Y)
6. Do not try to pull the workpiece back with the blade
turning. Turn the switch OFF, and carefully slide the
workpiece out when the blade is completely stopped.
USING WOOD FACING ON THE MITER GAUGE
(Fig. Y-l)
Slots are provided in the miter gauge of attaching an
auxiliary facing (1) to make it easier to cut very long or
short pieces. Select a suitable piece of smooth wood,
drill two holes through it and attach with screws. Make
sure the facing does not interfere with the proper
operation of the sawblade guard. When cutting long
workpieces, you can make a simple support by
clamping a piece of plywood to a sawhorse.

!
2

COMPOUND MITER CROSSCUTTING (FIG. AA)
This sawing operation is combining a miter angle
with a bevel angle.
1. Set the miter gauge (3) to the desired angle. Use
only the left side groove (2).
2. Set the blade (1) bevel to the desired angle.
3. Carefully push the miter gauge to begin the cutting
operation.

Fig. AA
3

MITERING (FIG. BB)
This sawing operation is the same as crosscutting
except the miter gauge is locked at an angle other than
g0 °
1. Hold the workpiece (2) firmly against the miter
gauge (3).
2. Feed the workpiece slowly into the blade (1) to
prevent the workpiece from moving.

Fig. CC-1
30"

3/8" Thick

p_ywood

base

_._;_"

tr _

Attach auxiliary fence to rip fence with two "C" clamps.
(Fig. CC-2)

Fig. CC-2

USING WOOD FACING ON THE RIP FENCE
(FIG.
CC)
When performing some special cutting operations, add
a wood facing (1) to either side of the rip fence (2).
1. Use a smooth straight 3/4" thick wood board (1) that
is as long as the rip fence.
2. Attach the wood facing to the fence with wood screw
(3) through the hole in the fence. A wood fence
should be used when ripping material such as thin
paneling to prevent the material from catching
between the bottom of the fence and the table.

Fig. CC

AUXILIARY FENCE (FIG. CC-1)
Making the base:
• Start with a piece of 3/8" plywood at least 5-1/2"
wide or wider and 30" long or longer.
• Cut the piece to shape and size shown:
Making the side:
• Start with a piece of 3/4" plywood at least 2-3/8"
wide or wider and 27" long or longer/
• Cut the piece to shape and size shown:
Putting it together:
• Put the pieces together, as shown:

DADO CUTS (FIG. DD)
1. The dado table insert is included with this saw.
Remove saw blade, blade guard, installed dado, and
dado table insert.
2. Instruction for operating the dado is packed with the
separately purchased dado set.
3. The arbor (1) on this saw restricts the maximum
width of the cut to 1/2".
4. It is not necessary to install the outside flange (2)
before screwing on the arbor nut (3). Make sure that
the arbor nut (3) is tight, and that at least one thread
of the arbor sticks out past the nut.
5. Use only the 6" dado set and keep the width t/2" or
less. It will be necessary to remove the blade guard
and splitter when using a dado blade. Always use
caution when operating a dado blade.
6. Use only the correct number of round outside blades
and inside chippers as shown in the dado set's
instruction manual. Blade or chipper must not
exceed 1/2".
7. Check saw to ensure that the dado will not strike the
housing, insert, or motor when in operation.

IZlWARNING l
For your own safety, always replace the blade, blade
guard assembly, and blade insert when you are
finished with the dado ..... *;^_

Fig. DD

j2
J
J

WARNING I
Make sure the screw heads do not stick out from the
bottom of the base, they must be flush or recessed.
The bottom must be flat and smooth enough to rest on
the saw table without rocking.

\
\
_3

MAINTAINING
GENERAL

YOUR

TABLE

SAW

Fig. EE

MAINTENANCE

IA WARNING
I
For your own safety, turn the switch OFF and remove the
switch key. Remove the plug from the power source outlet
before maintaining or lubricating your saw.
1. Clean out all sawdust that has accumulated inside the
saw cabinet and the motor.
2. Polish the saw table with an automotive wax to keep it
clean and to make it easier to slide the workpiece.
3. Clean cutting blades with pitch and gum remover.
4. A worn, cut, or damaged power cord should be replaced
immediately.

WARNING
I
All electrical or mechanical repairs should be attempted
only by a trained repair technician. Contact the nearest
Sears Service Center for service. Use only identical
replacement parts. Any other parts may create a hazard.
5. Use liquid dish washing detergent and water to clean all
plastic parts.
NOTE: Certain cleaning chemicals can damage plastic
parts.
6. Avoid use of the following cleaning chemicals or
solvents, ammonia and household detergents
containing ammonia.
BLADE RAISING AND TILTING MECHANISM (FIG. EE)
After each five hours of operation, the blade raising
mechanism and tilting mechanism should be checked for
looseness, binding, or other abnormalities. With the saw
dis-connected from the power source, turn the saw upside
down and alternately pull upward and downward on the
motor unit. Observe any movement of the motor mounting
mechanism. Looseness or play in the blade raising screw
(1) should be adjusted as follows:
1. Using a wrench, loosen nut (2).
2. Adjust nut (3) until it is finger-tight against the bracket
(4), then back off the nut (3) 1/6 turn.
3. Tighten nut (2) with the wrench, while holding nut (3)
in place. Maximum allowable play of screw rod (1) is
0.16" (4 mm).

Place a small amount of dry lubricant on bevel gear (2).
Screw rod (1) must be kept clean and free of sawdust, gum,
pitch, and other contaminants for smooth operation.
If excessive looseness is observed in any parts of the blade
raising mechanism or tilting mechanism, take the complete
unit to a Sears Service Center.
LUBRICATION
All motor bearings are permanently lubricated at the factory
and require no additional lubrication.
On all mechanical parts of your table saw where a pivot or
threaded rod are present, lubricate using graphite or silicone.
These dry lubricants will not hold sawdust as would oil or
grease.

I_WARNING
I
To avoidinjury
froman accidental
start,
turntheswitchOFF and alwaysremove theplugfromthepower sourcebefore
makingany adjustments.
• ConsultyourlocalSears ServiceCenterifforany reasonthemotorwill
notrun.

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Saw will not start

1. Saw not plugged in
2. Fuse blown or circuit breaker tripped
3. Cord damaged

1. Plug in saw
2. Replace fuse or reset circuit breaker
3. Have cord replaced by a Sears
Service Center
1. Check blade with square and adjust
positive stop
2. Check blade with square and adjust
to zero
1. Check and adjust rip fence
2. Select another piece of wood

Does not make accurate
45 ° and 90 ° rip cuts

1. Positive stop not adjusted correctly
2. Tilt angle pointer not set accurately

Material pinched blade
when ripping

1. Rip fence not aligned with blade
2. Warped wood, edge against fence is
not straight

Material binds on splitter

1. Splitter not aligned correctly with blade

1. Check and align splitter with blade

Saw makes unsatisfactory
cuts

1. Dull blade
2. Blade mounted backwards
3. Gum or pitch on blade

Blade does not raise or tilt
freely

Incorrect blade for work being done
5. Gum or pitch on blade causing erratic
feed
1. Rip fence out of adjustment
2. Splitter not aligned with blade
3. Feeding stock without rip fence
4. Splitter not in place
5. Dull blade
6. The operator letting go of material
before it is past saw blade
7. Miter angle lock knob is not tight
1. Sawdust and dirt in raising and tilting
mechanisms

1. Replace blade
2. Turn the blade around
3. Remove blade and clean with
turpentine and coarse steel wool
4. Change the blade
5. Clean table with turpentine and
steel wool
1. Align rip fence with miter gauge slot
2. Align splitter with blade
3. Install and use rip fence
4. Install and use splitter (with guard)
5. Replace blade
6. Push material all the way past saw
blade before releasing work
7. Tighten knob
1. Brush or blow out loose dust and
dirt

Blade does not come up
to speed

1. Extension cord too light or too long
2. Low house voltage

1. Replace with adequate size cord
2. Contact your electric company

Machine vibrates
excessively

1. Saw not mounted securely to
workbench
2. Bench on uneven floor

1. Tighten all mounting hardware
2.

3. Damaged saw blade

1. Miter gauge out of adjustment

1. Adjust miter gauge

Material kicked back from
blade

Does not make accurate
45 ° and 90 ° cross cuts

Reposition on flat level surface
Fasten to floor if necessary
Replace blade

10" TABLE SAW PARTS LIST

MODEL NO. 137.248880

L_k WARNINGJ
When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product
damage.

L,_ WARNINGJ
Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified
service technician. Repair service is available at your nearest Sears Service Center.
Always order by Model Number and I.D. number.
Schematic

I.D. NO.

DESCRIPTION

SIZE

2178

EXTENTION

WING

(RIGHT)

OKAP

CRRE.

PAN HD.

2179

EXTENTION

WING

(LEFT)

0KCH

CRRE.

PAN HEAD

09JK

WRENCH

0KCX

RE. PAN HD PLAIN

WASHER

TAPPING

8B31

TABLE

OKCY

RE. PAN HD PLAIN

WASHER

TAPPING

0B3H

INSERT

OKSW

STRAIN

0B3K

INSERT

OKWZ

LEAD

8B3R

WRENCH

OSZY

SLIDING

BASE

ASS'Y

8B84

WASHER

OSZZ

SLIDING

BASE

ASS'Y

0B8A

WARNING

OT00

SLIDING

BASE

ASS'Y

0BC2

LOCATION

0T03

SLIDING

BASE

ASS'Y

0BCW

UPER

18GN

UPER

TUBE

0BCX

EXTENTION

18GP

UPER

TUBE

0BD2

WARNING

LABEL

18GQ

PARALLEL

0BD3

WARNING

LABEL

10H4

UPER

TUBE

0J3P

WRENCH

HEX

18H5

UPER

TUBE

0J3U

WRENCH

HEX

20KA

SCALE

8J5L

FLAT WASHER

/s_5X 10-0.3

28KC

SCALE

8J6V

FLAT WASHER

3/16X3/8-0.022

20KD

SCALE

8J76

FLAT WASHER

1/4X3/4-1/16

28WQ

HEX.

HEX

STICK

LABEL

SEAT

TUBE

WING

4-64

3-90

QTY

I.D.

NO.

DESCRIPTION

SIZE

TAPPING

SCREW

& WASHER

M5X0.8-10

M5X0.8-12

SCREW

M5X0.8-10

SCREW

M5X0.8-12

SCREW

RELIEF

WIRE

QTY

ASS'Y

BRACKET

BOLT

ASS'Y

M6X1.8-50

0J95 ....................
SPRING WASHER .......................................................................................................................
_,_
6 .........
!........20Z7 .........
BLADE GUA'RD ASS'Y ..........................................................................................

0JAA

WASHER

0JAF

EXTERNAL

0JED

C-RING

0K9U

HEX

TOOTH

HD. TAPPING

LOCK

SCREW

WASHER

_s_8

211Q

SCALE

Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : No
Page Count : 30
Page Layout : SinglePage
Page Mode : UseNone
Producer : Goby Monitor Application version 3, 2, 1, 4
Create Date : Wed Aug 15 14:30:46 2007
Author :
Title :
Subject :

EXIF Metadata provided by EXIF.tools

Craftsman 137248880 User Manual TABLE SAW Manuals And Guides L0706477

CRAFTSMAN Saw Table Manual L0706477 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation