Craftsman 13953758 User Manual 3 FUNCTION MINI TRANSMITTER Manuals And Guides L0707150

CRAFTSMAN Garage Door Opener Manual L0707150 CRAFTSMAN Garage Door Opener Owner's Manual, CRAFTSMAN Garage Door Opener installation guides

User Manual: Craftsman 13953758 13953758 CRAFTSMAN 3-FUNCTION MINI TRANSMITTER - Manuals and Guides View the owners manual for your CRAFTSMAN 3-FUNCTION MINI TRANSMITTER #13953758. Home:Garage Door & Opener Parts:Craftsman Parts:Craftsman 3-FUNCTION MINI TRANSMITTER Manual

Open the PDF directly: View PDF .
Page Count: 2

,.odei 139.53758

3-Function Mini Transmitter Owners Manual

EC;,.O.rules prohibit adjustments to or modification of receiver and/or transmitter circuitry except for changing the code setting

and replacing transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Manufactured under 1 or more of the following US. patents: RE29,525; 4,037,201;4,750,118;4.806,930

i,ll ii ,i

MATCH THE CODE IN NEW AND EXISTING TRANSMITTERS

Remove the cover screw in NEW transmitter. Turn case over to access code switches #1 through #9. Be careful not

to move circuit board components. Locate code switches in c_iginal transmitter(s), (Refer to illustration)_ Set code switches

in the 3_Function Mini Transmitter to the same positions as code switches in the original transmitter.

NOTE 1: Code switches #2 through #g in ALL transmitters used to operate a receiver must be sot to match. (Coda

switch #1 on 8 3-function transmitter Is neutral. Set it to ANY position. It will not affect the code selected.

NOTE 2: If the original transmltter(s) has only 7or 8 code switches, set code switches #8 and!or #9 to center

(0) position tn new transmitter.

o-_

JJ "0' "1 St_,ndard [I

3-Function 0:3 -.,_ Standard

i

I" 1 €2-9)

REPLACEMENT PARTS: Transmitter Housing Only (No circuit board) - 4tA3592; 12V Battery - 10A14

CHANGE THE CODE IN RECEIVER AND TRANSMITTER(S)

53000SR SERIES

0NITH RECEIVER 'SR' CODE BUTTON)

Garage Door Openers and Light Controls

(illustration A shows a garage door opener receiver)

Selec_ a traz_rni_ef

pushbuttonIo X

operatereceiver _ t_ wffr °u_ _L

Key Ring Push _ltons

Holder "S_' Indicator ....

CodeButton Light

Make sure all transmitters areset to matching code switch

positions as described above.

1o Press the 'SR' code button on your receiver (illt_tra-

tion A). The indicator light wilt turn ONe

2. STAND AWAY FROM DOOR and press the transmit-

ter's SELECTED PUSH BUTTON. The indicator light

will turn OFFand door will move.Code in receiver now

matches transmitter(s) code and will activatewhen the

selected transmitter push button is pressed,

NOTE: I! transmitter push button ts not pressed

within 30 seconds, the Indicator light will turn OFF.

Repeat 1 and 2,

To use the 3-Function Mtnl Transmitter with other

53000SR Serlse receivers: Select another transmitter

push button to operate e Light Controlor additional garage

door opener. Make sure all transmitters used to operate

receiver are set to the same cote (as described above).

Then repeal I and 2.

You can select adifferent transmitter push button to oper-

ate each device.

53000 SERIES

(WITH RECEIVER CODE SWITCHES)

Garage Door Openers and Light Controls

(illustration B shows a garage door opener receiver)

Push(_ulton Select a

transmitter

_PushButton pushbutton

f _ J (+)

Key Ring Push Button to operate

g Holder (O) receiver

IF_D WHT BLK Y_:L

codeswitch#1

1234_;678ii to positJortthe!

!ltltlMltl pushbur_on

CodeSwitch

#1

Makesure alltransmitters are set to matching code switch

positionsas described above.

1, Select a transmitterpush buttonto operatethe receiver

as shown in Figure 13.

2, Set RECEIVER code switch #1 to match the position

of the transmitter push button selected. Refer to

illustration BeThen set remaining code switches in

receiver to match the transmitter(s) code switch

positions.

NOTE: If the receiver has only 7 or 8 switches, sot

transmitter switch #8 and/or #g to (0).

Touse the 3-FuncttonMlnl Transmitterwith other 53000

Series receivers: Set receiver code switch #1 to match

the positionof anothertransmitterpush button. Then set

remaining code switches to match transmitter(s)code

switches,

Code switches #2 through #9 in all transmitters used

to operate the receiver MUST be set to matching

positions.

IJIIL,I,ll,_,Jll,llJ_Ui

©19g0, Sears Roebuck & Company

114Al160_._ All RlghfJiReserved Printed In Mexico

Sears Model 139.53758

3-Function Mini Transmitter

REPLACEMENT PARTS:

Transmitter Housing Only (No circuit board)

12V Battery

41A3592

10A14