Craftsman 143014502 User Manual ENGINE Manuals And Guides L0101251
CRAFTSMAN Engine Manual L0101251 CRAFTSMAN Engine Owner's Manual, CRAFTSMAN Engine installation guides
User Manual: Craftsman 143014502 143014502 CRAFTSMAN ENGINE - Manuals and Guides View the owners manual for your CRAFTSMAN ENGINE #143014502. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman ENGINE Manual
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
operator's
manual
MODEL
SOLID
NO. 143.014502
STATE
IGNITION
ENGIN
CAUTION:
• Operating
Read RULES for
Safe OPERATION
and INSTRUCTIONS
• Maintenance
• Repair Parts
Carefully
WARNING:
California Proposition 65
known to the State of California
to cause cancer,
The engine exhaust from this product contains
birth defects or other reproductive
harm.
chemicals
Sold by SEARS, ROEBUCK AND CO., CHICAGO, IL 60684 U.S.A.
and SEARS CANADA, INC., TORONTO, ONTARIO, CANADA
Printed in U.S.A.
lo-t-oo 181-1248-11
RECOIL STARTER
OIL FILL PLUG AND
DIPSTICK
STARTER\
HANDLE
_l
]J
MODEL AND
D.D.M.
DECAL
SPARK
PLUG
WIRE
\
lINE
CONTROL
LEVER
OIL DRAIN PLUG
CARBUERTOR
SPARK PLUG
COOLING
,MUFFLER
FINS
Figure
THIS SYMBOL
POINTS OUT
ENDANGER
THE PERSONAL
BOTrOM
OF ENGINE
1
IMPORTANT
SAFETY INSTRUCTIONS
WHICH
SAFETY
AND/OR PROPERTY
OF YOURSELF
FOLLOW
ALL INSTRUCTIONS
IN THIS MANUAL
AND ANY PROVIDED
THIS ENGINE IS USED BEFORE
ATTEMPTING
TO OPERATING.
IF NOT FOLLOWED
COULD
AND OTHERS.
READ AND
WITH
THE EQUIPMENT
ON WHICH
THESE SYMBOLS MAY APPEAR ON THE ENGINE:
,-=.,,
FAST
O
SLOW
I11FULL
OFFI"
CHOKE
STOP
OIL & FUEL RECOMMENDATIONS
ENGINE,
(_ A CLEAN,
HIGH
YOU WILL
NEED
QUALITY,
THE
BEFORE
FOLLOWING:
DETERGENT
OIL.
Be sure original container is marked:
A,P.I. service "SF"- "SJ".
FOR SUMMER (ABOVE 32oF;O°C) USE SAE 30 OIL.
Using multigrade oil will increase oil consumption.
FOR WINTER (BELOW 32°F;0°C) USE SAE 5W30 OIL. (SAE 10W is
an acceptable substitute.)
DO NOT USE 10W40 OIL.
OIL BUMP CAPACITY: 21 ounces (1-1/4 U.S. pints)
.62 liter
(_)A
FRESH,
PREMIUM,
ONLY.
NOTE:
CLEAN,
UNLEADED
OR REFORMULATED
DO NOT USE LEADED
DO NOT USE GASOLINE
REGULAR,
AUTOMOTIVE
GASOLINE.
CONTAINING
1_
STARTING
READ ALL INSTRUCTIONS
PROVIDED
WITH THE EQUIPMENT
ON
,_WHICH
THIS ENGINE IS USED.
THIS ENGINE IS EQUIPPED WITH A FEDERALLY MANDATED
MECHANISM WHICH STOPS THE ENGINE. DO NOT INTERFERE
WITH OR BYPASS THIS MECHANISM. PARTS OF THE MECHANISM
MAY BE SUBJECT TO WEAR AND MUST BE CHECKED ONCE A YEAR
BY AN AUTHORIZED
SEARS ROEBUCK AND CO, (OR SEARS
CANADA, INC.) SERVICE CENTER. IN THE EVENTTHE MECHANISM
FAILS FOR ANY REASON, YOU MUST NOT USE THE ENGINE UNTIL
CORRECTED BY AN AUTHORIZED SEARS ROEBUCK AND CO. (OR
SEARS CANADA, INC.) SERVICE CENTER.
UNLEADED
GASOLINE
METHANOL
PRIMER
IMPORTANT
KEEP THIS MANUAL HANDY AT ALL TIMES FOR FUTURE
REFERENCE.
READ IT CAREFULLY AND FAMILIARIZE
YOURSELF WITH THE OPERATING, MAINTENANCE AND
SAFETY INSTRUCTIONS. THIS MANUAL ALSO CONTAINS A
COMPLETE PARTS LISTING.
NOTE: Engines which are certified to comply with California and U.S.
EPA emission regulations for SORE (Small Off Road Equipment), are
certified to operate on regular unleaded gasoline, and include the
following emission control systems: Engine Modification (EM), and
Three-way Catalyst (TWC) (if so equipped).
TO OPERATE
I ,'-L
_/_ISCONNECT
SPARK PLUG WIRE FROM SPARK PLUG AND
1-rACH IT TO RETAINING POST (see Figure 6 on Page 3).
(_)
ENGINE
BRAKE
CABLE
AND
STARTER
ROPE:
BRAKE CABLE (see Figure 2):
Attach engine brake cable to brake mechanism
as shown.
STARTER
ROPE:
A.
Depress mower control bar (see Figure 3) against mower
handle and hold it in this position.
(WOOD
ALCOHOL).
Gasoline containing up to 10% ethanol or grain alcohol
('Gasohol"), or up to 15% MTBE (Methyl Tertiary Butyl Ether), may be
used but requires special care when engine is unused for extended
periods.
See "STORAGE" instructions of Page 5,
NOTE: Use clean oil and fuel and store in approved, clean covered
containers. Use clean fill funnels.
Never use 'stale" gasoline left over from last season or stored for long
periods.
Page
INSTALL
B.
!
Pull at least 2 feet of starter rope out of starter and tie a slip
knot at starter to prevent starter rope from rewinding back into
starter.
181-1248-11
BEFORE
STARTING
(Continued)
C.
Slide rope stop (see Figure 2) onto starter rope and feed
starter rope through rope guide on mower handle (see
Figure 4).
D.
Feed starter rope through starter handle (see Figure 5) and
tie a left hand knot, leaving 1/2 inch to 1 inch of starter rope
extending beyond left hand knot. DO NOT PULL LEFT HAND
KNOT INTO STARTER HANDLE YET.
E.
With starter handle resting on rope guide (see Figure 4),
check starter rope for slack. If there is any slack, pull more
starter rope through starter handle and relocate left hand
knot to eliminate slack.
F.
G.
Untie slip knot at starter.
Pull left hand knot into starter handle.
H.
Position rope stop 2 to 3 inches from starter (see Figure 2)
and fasten it to starter rope by gripping it with pliers and
forcing staple through starter rope until staple is even with
outside of rope stop.
BEFORE
(_)
STARTING
(Continued)
FILL FUEL TAN K with gasoline as specified in the preceding
"OIL & FUEL RECOMMENDATIONS," item 2.
NEVER MIX OIL WITH GASOLINE
Never use "stale" gasoline left over from last season or stored for
long periods.
,_
NEVER FILL FUEL TANK INDOORS. NEVER FILL FUEL TANK
WHEN ENGINE IS RUNNING OR HOT. DO NOT SMOKE WHEN
!
FILLING FUELTANK.
p
_1_ NEVER FILL FUEL TANK COMPLETELY, FILL TANK TO 1/2"
BELOW BOTTOM OF FILLER NECK TO PROVIDE SPACE FOR
FUEL EQUIPMENT
AND
EXPANSION. BEFORE
WIPE ANYSTARTING
FUEL SPILLAGE
ENGINE.
FROM ENGINE
,_ANY
LIQUEFIED
PETROLEUM
NATURAL
GAS FUEL
SYSTEM
MUST BE
LEAKPROOF(LPG)OR
AND MEETALL
APPLICABLE
L CODES AND REGULATIONS.
I
_,
THE ALUMINUM COMPONENTS OF YOUR NEW ENGINE HAVE
BEENTREATED WITH A PRESERVATIVE INTENDED TO MAINTAIN
THE APPEARANCE OF THE ENGINE. THE PRESERVATIVE WILL
CURE DURING THE INITIAL USE OF THE ENGINE. A SMALL
AMOUNT OF SMOKE MAY BE PRESENT DURING THE INITIAL USE
OF THE PRODUCT AND SHOULD BE CONSIDERED NORMAL.
(_
CHECK
(_
CHECK
_LA.
OIL LEVEL:
IMPORTANT:
NEVER RUN ENGINE UNLESS OIL LEVEL IS
BETWEEN "FULL" AND "ADD" MARKS ON
DIPSTICK.
B.
THE
BE SURE EQUIPMENT IS IN NEUTRAL GEAR WITH I
CLUTCHES, BELTS, CHAINS AND SAFETY SWITCHES I
DISENGAGED.
(FOLLOW
EQUIPMENT
MANU-/
FACTURER'S INSTRUCTIONS.) THIS SHOULD PLACE
ANY SAFETY SW TCHES N SAFE START NG POSIT ON.
Be sure spark plug wire is attached to spark plug (see Figure
1).
CHECK OIL LEVEL OFTEN DURING ENGINE BREAK-IN.
NEVER RUN ENGINE UNLESS OIL FILL PLUG IS TIGHTENED
SECURELY INTO OIL FILL HOLE.
MOWER
A.
B.
C.
D.
CONTROL BAR
E.
F.
FOLLOWING:
POSITION EQUIPMENT SO ENGINE IS LEVEL.
Clean area around oil fill plug (see Figure 1).
Remove oil fill plug and dipstick.
Wipe dipstick clean, insert it into oil fill hole and tighten
securely.
Remove oil fill plug and check oil level. If level is not up to
"FULL" mark on dipstick, add recommended oil, until it is.
POUR SLOWLY. Wipe dipstick clean each time oil level is
checked. DO NOT FILL ABOVE "FULL" MAR K ON DIPSTICK.
Replace
oil fill plug and tighten
securely.
See
"MAINTENANCE"
section for any future oil level and oil
change instructions (see Page 3).
_
\
MOWER_
HANDLE
'_"_
Figure
3
HANDLE
ROPE GUIDE
ROPE STOP
STARTER ROPE
2 TO 3
INCHES
STARTER
NO SLACK
PERMISSIBLE
MOWER /
HANDLE
Figure 4
LEFT HAND
KNOT
STARTER
ROPE
STARTER
HANDLE
I
1/2 TO 1 INCH
Figure 2
Page 2
Figure 5
181-1248-11
STARTING
MAINTENANCE
,_NEVER
RUN ENGINE INDOORS OR IN ENCLOSED, POORLY
VENTILATED
AREAS.
ENGINE
EXHAUST
CONTAINS
CARBON MONOXIDE, AN ODORLESS AND DEADLY GAS
(CARBON
MONOXIDE
IS ALSO PRESENT
IN ENGINE
EXHAUST FROM LIQUID PETROLEUM (LPG) AND NATU RAL
GAS FUEL SYSTEMS).
,_
,_
t
(i) CHECK
(_)
(_
A.
ENGINE:
_.
,
B.
The carburetor on your engine has been completely adjusted
at the factory. When starting a cold engine, push red primer
bulb firmly with your thumb 3 times, allowing primer bulb
to return completely to original position between pushes.
Repeat the above for each starter operation as necessary.
NOTE: DO NOT USE PRIMER TO RESTART A WARM
ENGINE AFTER A SHORT SHUTDOWN.
B.
Operate mower control to release engine brake.
C.
Grasp starter handle (see Figure 4) and pull rope out, slowly,
until it pulls slightly harder. Let rope rewind slowly. Then pull
rope with a rapid full arm stroke. Let rope rewind SLOWLY.
Do not let starter handle snap back against rope guide (see
Figure 4).
• D.
Repeat instructions B and C if necessary, until engine starts.
NOTE: If engine does not start, repeat instructions A, B, C
and D until it starts,
ENGINE SPEED: Engine speed is controlled by the engine control
(see Figure 1). Engine control should be in HI position for high grass
conditions and for most efficient bagging in heavy grass conditions,
and in LOW position for light grass, trimming and for fuel economy.
C.
(_
mower manufacturer's
AFTER
ENGINE
OIL:
DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG
AND ATTACH IT TO RETA N NG POST (see F gure 6).
Hosit_onequipment so engine oil drain plug is lowest point
on engine.
Remove oil drain plug and oil fill plug to drain oil (see Figure
1).
D.
E.
Replace oil drain plug and tighten securely.
Fill oil sump with recommended oil. See "OIL & FUEL
RECOMMENDATIONS"
and "CHECK OIL LEVEL" on Page
1.
F. Replace oil fill plug and tighten securely.
G. Connect spark plug wire to spark plug.
H. Wipe up any spilled oil and/or gasoline.
NOTE: If it is difficult to reach the oil drain plug, drain fuel.
Remove oil fill plug and tip mower on its side. Drain oil
into a suitable container.
(_) AIR CLEANER
STOPPING
(_See
CHANGE
Change oil after first two (2) operating hours and every 25
operating hours thereafter, more often if operated in extremely
dusty or dirty conditions. Change oil while engine is still warm
from recent runnin_a.
Move engine control (see Figure 1) to HI Position.
(_) START
OIL LEVEL:
Check oilleveleveryfive(5) operatinghoursor eachtimeengine
is used.See "3CHECK OIL LEVEL"in "BEFORE STARTING"on
Page 2.
KEEP HANDS, FEET, HAIR AND LOOSE CLOTHING AWAY
FROM ANY MOVING PARTS ON ENGINE AND EQUIPMENT.
,_WARNING
TEMPERATURE
OF MUFFLER AND NEARBY
AREAS MAY EXCEED 150°F (65°C). AVOID THESE AREAS.
I
WARNING
AREAS
MAYTEMPERATURE
EXCEED 150°F (65°C).
OF MUFFLER
AVOID THESE
AND NEARBY
AREAS. 1
(see Figure7):
NEVER RUN ENGINE WITHOUT COMPLETE
INSTALLED ON ENGINE.
instructions.
Replace filter once a year or more often if used in extremely dusty
or dirty conditions.
DO NOT ATTEMPT TO CLEAN OR OIL FILTER.
A.
Turn cover to the left (counterclockwise) and remove it and
filter from flange. Discard filter.
B.
C.
Clean cover and flange thoroughly•
Insert new filter into cover.
D.
Position cover and filter against flange with tab on cover
inserted into lower left corner of slot in flange.
E.
Push cover firmly against flange and turn it to the right
(clockwise) as far as it will go. Be sure retainers are locked
around flange.
FLANGE
IS STOPPED:
DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG
AND ATTACH IT TO RETAINING POST (see Figure 6).
,_B.
NEVER
ENGINE
WITH FUEL
IN TANK INDOORS
OR IN STORE
ENCLOSED,
POORLY
VENTILATED
AREAS,
WHERE FUEL FUMES MAY REACH AN OPEN FLAME,
SPARK OR PILOT LIGHT AS ON A FURNACE, WATER
HEATER, CLOTHES DRYER OR OTHER GAS APPLIANCE.
PLUG
RETAINER
FILTER
COVER
SLOT
TURN COVER TO THE RIGHT
(CLOCKWISE) TO TIGHTEN
SPARK PLUG
WIRE
POST
Figure 6
]
Replacement filters are available at any Sears Roebuck and Co.
(or Sears Canada, Inc.) Service Center• To install new filter.
proceed as follows:
,_A.
RETAINING
AIR CLEANER
Page 3
Figure 7
_f
TURN COVER TO
THELEFT(COUNTERCLOCKWISE)TO
REMOVE
181 - t 248-11
MAINTENANCE
(_
SPARK
(Continued)
STORAGE
PLUG (see Figure8):
,_
NEVER STORE ENGINE WITH FUEL IN TANK INDOORS 0RIN_
ENCLOSED, POORLY VENTILATED AREAS, WHERE FUEL I
FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT I
LIGHT AS ON A FURNACE, WATER HEATER, CLOTHES I
DRYER OR OTHER GAS APPLIANCE.
IF ENGINE IS TO BE UNUSED FOR 30 DAYS OR MORE,
PREPARE AS FOLLOWS:
This sparkignition system meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
This engine
complies with all current Australian and New Zealand limitations
regarding electromagnetic interference. Check spark plug yearly
or every 100 operating hours.
A.
Clean area around spark plug.
B.
Remove and inspect spark plug.
C.
Replace spark plug if electrodes are pitted, burned or
porcelain is cracked. For replacement use Champion
RJ19LM.
(_
A.
NOTE: A resistor spark plug must be used for replacement.
D,
E.
DRAIN
,_
Check electrodes gap with wire feeler gauge and set gap at
.030 if necessary.
FUEL SYSTEM:
Remove all gasoline from carburetor and fuel tank to prevent
gum deposits from forming on these parts and causing
possible malfunction of engine.
DRAIN
CONTAINER
OUTDOORS,
AWAY FUEL
FROM INTO
OPENAPPROVED
FLAME. BE
SURE ENGINE
IS COOL.
DO NOT SMOKE.
I
Install spark plug, tighten securely.
a.
ELECTRODES
\
Run engine until fuel tank is empty and engine stops due to
lack of fuel.
NOTE:
Fuel stabilizer (such as ULTRA-FRESH TM) is an
acceptable alternative in minimizing the formation of fuel
gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found
on stabilizer container. Run engine at least 10 minutes after
adding stabilizer to allow it to reach carburetor.
PORCELAIN
.030 GAP
_)
CHANGE
Figure 8
(_) COOLING
Changeoilifithas notbeen changedin the lastthree (3) months.
See "CHANGE OIL" instructions
in "MAINTENANCE" section on
Page 3,
SYSTEM:
IMPORTANT: Frequently remove any grass clippings, dirt and
debris from cooling fins, air intake screen and levers and linkage
(see Figure 1). This will help ensure adequate cooling and
correct engine speed.
(_)
OIL CYLINDER
AND KEEP
THESE
ITEMS
BORE:
A.
Remove spark plug and pour one (1) ounce (30 mi) of engine
oil into spark plug hole.
B.
Cover spark plug hole with a rag.
C.
Crank engine over, slowly, several times.
CHECK ENGINE AND EQUIPMENT OFTEN FOR LOOSE NUTS,
,_BOLTS
AND ATTACHMENTS,
TIGHTENED.
I
OIL:
I
ADJUSTMENTS
_k.
DO NOT MAKE UNNECESSARY
ADJUSTMENTS.
FACTORY
SETTINGS ARE SATISFACTORY FOR MOST APPLICATIONS AN D
CONDITIONS.
IF ADJUSTMENTS ARE NEEDED, PROCEED AS
FOLLOWS:
AVOID
SPRAY
FROM
SPARK
PLUG
CRANKING
ENGINE
OVER
SLOWLY.
D.
HOLE WHEN
Replace spark plug.
(_) CLEAN
ENGINE:
Remove any cJippings,
dirt, or chafffrom exteriorof engine.
CARBURETOR
GENERAL
If you think your carburetor needs adjusting, see your nearest
SEARS, ROEBUCK AND CO. (OR SEARS CANADA, INC.)
SERVICE CENTER. Engine performance should not be affected
at altitudes up to 7,000 feet. For operation at higher elevations,
contact your nearest SEARS, ROEBUCK AND CO. (OR SEARS
CANADA, iNC.) SERVICE CENTER.
ENGINE
Just as your automobile needs professional mechanical maintenance
from time to time, so does your Craftsman engine. Replacement of the
spark plug and air cleaner is made necessary by NORMAL use.
Professional Air-Cooled Engine Service is as close as your nearest
Sears Roebuck and Co. (or Sears Canada, Inc.) Service Center.
SPEED
I
_NEVER
FACTORYTAMPER
SET WITH
FOR ENGINE
PROPERGOVERNOR
ENGINE WHICH
SPEED.IS II
OVERSPEEDING ENGINE ABOVE FACTORY HIGH SPEED
SETTING CAN BE DANGEROUS.
J CHANG NG OF ENGINE-GOVERNED
SPEED WILL VOID
l ENGINE WARRANTY"
I
A yearly check-up or tune-up by Sears is a good idea to avoid
breakdowns or delay.., do it at the end of the season, then you're ready
for the next. We even prepare it for storage for you.
Page 4
181-1248-11
TROUBLESHOOTING
THE FOLLOWING
MAY HELP AVOID A DELAY IN YOUR WORK
SAVE THE EXPENSE OF A SERVICE CALL.
OR
ENGINE FAILS TO START OR STARTS WITH DIFFICULTY
CAUSE
:Controls not in start position.
REMEDY
Move ENGINE CONTROL or equipment control to "HI" or
START postion, See "STARTING" instructions in this
manual.
Spark plug wire disconnected from spark plug.
Connect SPARK PLUG WIRE to SPARK PLUG.
Spark plug fouled.
Remove SPARK PLUG and clean it. See "SPARK
PLUG" instructions in "MAINTENANCE" section in this
manual.
Spark plug porcelain cracked.
Install new spark plug.
Insufficient fuel,
Fill FUEL TANK per "BEFORE STARTING" instructions.
Water or dirt in fuel.
Drain FUEL TANK and re-fill with clean, fresh gasoline.
See "BEFORE STARTING" instructions in this manual.
Improper carburetor adjustment
Adjust carburetor (if applicable).
section in this manual.
See "ADJUSTMENTS"
ENGINE LACKS POWER
CAUSE
REMEDY
Dirty air cleaner.
Replace or clean air cleaner per "AIR CLEANER"
instructions in "MAINTENANCE" section in this manual,
Improper carburetor adjustment.
Adjust carburetor (if applicable).
section in this manual.
Lack of lubricaiton.
Fill oil sump to proper level, See "BEFORE STARTING"
instructions section in this manual.
See "ADJUSTMENTS"
ENGINE MISSES UNDER LOAD
REMEDY
CAUSE
Spark plug fouled.
Remove SPARK PLUG and clean it. See "SPARK
PLUG" instructions in "MAINTENANCE" section in this
manual.
Spark plug porcelain cracked.
Install new SPARK PLUG.
Improper spark plug gap.
Regap SPARK PLUG electrodes. See "SPARK PLUG"
instructions in "MAINTENANCE" section in this manual.
Improper
Adjust carburetor (if applicable).
section in this manual,
carburetor
adjustment
Page 5
See "ADJUSTMENTS"
181-1248-11
SEARS,
Federal
and California
CALIFORNIA
& US EPA EMISSION
WARRANTYSTATEMENT
ROEBUCK
AND CO.
Emission Control Systems
Small Off-Road Engines
CONTROL
The U, S Environmental
Protection Agency ("EPA"), the California Air
Resources Board ("CARB") and Sears, Roebuck and Co are pleased to explain
the Federal and California Emission Control Systems Warranty on your new
small off-road engine.
In California, new 1995 and later small off-road engines
must be designed, built and equipped to meet the State's stringent anti-smog
standards.
In other states, new 1997 and later model year engines must be
designed, built and equipped, at the time of sale, to meet the US EPA
regulations for small non-road engines. Sears, Roebuck and Co will warrant the
emission control system on your small off-road engine for the periods of time
listed below, provided there has been no abuse, neglect, unapproved
modification, or improper maintenance
of your small off-road engine.
Your emission control system may include parts such as the carburetor, ignition
system and exhaust system
AIso included may be the compression
release
system and other emission-related
assemblies.
C.
1
Designed, built and equipped so as to conform with all applicable
regulations adopted b the Air Resources Board pursuant to i s au he y
_nChap ers
and 2, _art 5, Division 26 of the Health and Safety Code,
2
Free from defects in materials and workmanship which, at any time
during the ECS Warranty Period, will cause a warranted emissions-related
part to fail to be identical in all material respects to the part as described
in the engine manufacturer's
application for certification.
The ECS Warranty
as follows:
WARRANTY
SYSTEM
to emissions-related
parts on your engine,
2.
Any warranted, emissions-related
part which is scheduled only for regular
inspection as specified in the Owner's Manual shall be warranted for the
ECS Warranty Period. A statement in such written instructions to the
effect of "repair or replace as necessary", shall not reduce the ECS
Warranty Period. Any such part repaired or replaced under the ECS
Warranty shall be warranted for the remainder of the ECS Warranty
Period.
3.
Any warranted, emissions-related
part which is scheduled for replacement
as required maintenance in the Owner's Manual, shall be warranted for the
period of time prior to the first scheduled replacement point for that part
If the part fails prior to the first scheduled replacement,
the part shall be
repaired or replaced by Sears, Roebuck and CO. according to Subsection
4 below
Any such emissions-related
part repaired or replaced under the
ECS Warranty, shall be warranted for the remainder of the ECS Warranty
Period prior to the first scheduled replacement point for such emiss=onsrelated part.
RESPONSIBILITIES
As the small off-road engine owner, you are responsible for the performance of
the required maintenance listed in your Owner's Manual, but Sears, Roebuck and
Co. will not deny warranty solely due to the lack of receipts o o you
a u e o
provide written evidence of the performance
of all scheduled maintenance.
As the small off-road engine owner, you should, however, be aware that Sears,
Roebuck and Co. may deny you warranty coverage if your small off-road
engine or a part thereof has failed due to abuse, neglect, improper maintenance
or unapproved modifications.
4. Repair or replacement of any warranted, emissions-related
part under this
ECS Warranty shall be performed at no charge to the owner at a Sears,
Roebuck and Co Authorized Service Outlet
You are responsible
for presenting your small off-road engine to a Sears,
Roebuck and Co. Authorized Service Outlet as soon as a problem exists
The
warranty repairs should be completed in a reasonable amount of time, not to
exceed 30 days.
5. The owner shall not be charged for diagnostic labor which leads to the
determination
that a part covered by the ECS Warranty is in fact
defective, provided that such diagnostic work is performed at a Sears,
Roebuck and CO Authorized Service Outlet.
Warranty service can be arranged by contacting either a Sears, Roebuck and
Co. Authorized Service Outlet, or by contacting Sears, Roebuck and Co. at
1-800-473-7247,
IMPORTANTNOTE
This warranty statement explains your rights and obligations under the Emission
Control System Warranty ("ECS Warranty") which is provided to you by Sears,
Roebuck and Co. pursuant to California law. See also the Sears, Roebuck and
CO, Limited Warranties for Sears, Roebuck and CO which is enclosed therewith
on a separate sheet and also is provided to you by Sears, Roebuck and Co.
The ECS Warranty applies only to the emission control system of your new
engine. To the extent that there rs any conflict in terms between the ECS
Warranty and the Sears, Roebuck and Co, Warranty, the ECS Warranty shall
apply except in any circumstances
in which the Sears, Roebuck and Co
Warranty may provide a longer warranty period
Both the ECS Warranty and
the Sears, Roebuck and Co. Warranty describe important rights and obligations
with respect to your new engine.
Warranty service can only be performed by a Sears, Roebuck and Co
Authorized Service Outlet.
At the time of requesting warranty service, evidence
must be presented of the date of sale to the original purchaser
The purchaser
shall pay any charges for making service calls and/or for transporting
the
products to and from the place where the inspection and/or warranty work is
performed.
The purchaser shall be responsible for any damage or loss incurred
in connection with the transportation
of any engine or any part(s) thereof
submitted for inspection and/or warranty work.
6.
Sears, Roebuck and Co. shall be liable for damages to other original
engine components
or approved modifications
proximately caused by a
failure under warranty of an emission-related
part covered by the ECS
Warranty
7
Throughout the ECS Warranty Period, Sears, Roebuck and Co. shall
maintain a supply of warranted emission-related
parts sufficient to meet
the expected demand for such emission-related
parts
8.
Any Sears, Roebuck and Co authorized and approved emission-related
replacement part may be used in the performance
of any ECS Warranty
maintenance or repair and will be provided without charge to the owner.
Such use shall not reduce Sears, Roebuck and Co. ECS Warranty
obligations
g.
Unapproved add-on or modified parts may not be used to modify or
repair a Sears, Roebuck and Co. engine
Such use voids this ECS
Warranty and shall be sufficient grounds for disallowing an ECS Warranty
claim
Sears, Roebuck and Co shall not be liable hereunder for failures
of any warranted parts of a Sears, Roebuck and Co engine caused by
the use of such an unapproved add-on or modified part
EMISSION-RELATED
PARTS INCLUDE
THE FOLLOWING:
1. Carburetor Assembly and its Internal Components
a) Fuel filter
b) Carburetor gaskets
c) Intake ptpe
2. Air Cleaner Assembly
a) Air filter element
3. Ignition System, including:
a) Spark plug
b) Ignition module
c) Flywhee! assembly
4 Catalytic Muffler (if so equipped)
a) Muffler gasket (if so equipped)
b) Exhaust manifold (if so equipped)
5 Crankcase Breather Assembly and its Components
a) Breather connection tube
If you have any questions regarding your warranty rights and responsibilities,
you should contact Sears, Roebuck and Co at 1-800-473 7247.
EMISSION CONTROL
only pertains
Any warranted, emissions-related
parts which are not scheduled for
replacement as required maintenance in the Owner's Manual shall be
warranted for the ECS Warranty Period. If any such part fails during the
ECS Warranty Period, it shall be repaired or replaced by Sears Roebuck
and Co. according to Subsection 4 below. Any such part repaired or
replaced under the ECS Warranty shall be warranted for any remainder of
the ECS Warranty Period
Emission control systems on 1995 and later model year California small off-road
engines are warranted for two years as hereinafter noted
In other states, 1997
and later model year engines are also warranted for two years, if, during such
warranty period, any emission-related
part on your eng4ne is defective in
materials or workmanship, the part will be repaired or replaced by Sears,
Roebuck and Co.
OWNER'S
Warranty
B. GENERAL EMISSIONS WARRANTY COVERAGE:
Sears, Roebuck and Co.
warrants to the original, end-use purchaser of the new engine or equipment and
to each subsequent purchaser that each of its small off-road engines is:
Where a warrantable condition exists, Sears, Roebuck and Co, will repair your
small off-road engine at no cost to you for diagnosis, parts and labor
MANUFACTURER'S
EMISSION CONTROL
WARRANTY COVERAGE
Limited
SYSTEM WARRANTY
Emission Control System Warranty ("ECS Warranty") for !995 and later model
year California small off-road engines (for other states, 1997 and later model
year engines):
A APPLICABILITY:
This warranty shall apply to 1995 and later mode! year
California small off-road engines (for other states, 1997 and later model year
engines).
The ECS Warranty Period shall begin on the date the new engine or
equipment is delivered to its original, end use purchaser, and shall continue for
24 consecutive
months thereafter
10/22_9
Sears, Roebuck
and Co., Hoffman
Page 6
Estates,
IL 60179
EPA/CARB
U.S.A.
181-1248-11
CRAFTSMAN
4-CYCLE ENGINE
MODEL:143.014502
O--
370K
_261
298
900
,300
370R370C
400
135
I
130
12-126
7
101
120
119
416
195
125
3O
46
182
185
?
178
241
<.
/_
238
245
250
Page 7
181-124_8-11
CRAFTSMAN
Ref.
No.
Part
No.
1
2
6
7
12
12A
12B
14
15
16
17
18
19
2O
3O
4O
4O
4O
41
41
37280
26727
33734
36557
36775
36558
36694
28277
30589
34839A
31335
651018
36281
32600
36793
35544A
35545A
35546
35541
35542
41
35543
42
42
42
43
45
46
48
50
52
69
70
35547A
35548A
35549
20381
36777
32610A
27241
37575
29914
*37130
34311E
72
75
80
81
82
83
86
89
9O
92
93
100
101
103
104
110
119
120
125
126
130
135
150
151
151A
36083
27897
30574A
30590A
30591
30588A
650488
611004
611112
650815
650816
34443C
610118
651007
37480
37047
*37028
36825
37288
37289
6021A
37598
31672
31673
40017
4-CYCLE ENGINE
Pad Name
Cylinder (Incl. 2,20 & 150)
Dowel Pin
Breather Element
Breather Ass'y. (Incl. 6 & 12A)
Breather Tube
Breather Cover & Tube (Incl. 12B)
Breather Tube Elbow
Washer
Governor Rod (Incl. 14)
Governor Lever
Governor Lever Clamp
Screw, Torx T-15, 8-32 x 19/64"
Extension Spring
Oil Seal
Crankshaft
Piston, Pin & Ring Set (Std.)
Piston, Pin & Ring Set (.010" OS)
Piston, Pin & Ring Set (.020" GS)
Piston & Pin Ass'y. (Std.) (Incl, 43)
Piston & Pin Ass'y. (.010" OS) (Incl.
43)
Piston & Pin Ass'y. (.020" OS) (Incl.
43)
Ring Set (Std.)
Ring Set (.010" OS)
Ring Set (.020 OS)
Piston Pin Retaining Ring
Connecting Rod Ass'y. (Incl. 46)
Connecting Rod Bolt
Valve Lifter
Camshaft (NCR)
Oil Pump Ass'y.
Mounting Flange Gasket
Mounting Flange (Incl. 72 thru 83,
306)
Oil Drain Plug
Oil Seal
Governor Shaft
Washer
Governor Gear Ass'y. (Incl. 81)
Governor Spoof
Screw, 1/4-20 x 1-1/4"
Flywheel Key
Flywheel
Belleville Washer
Flywheel Nut
Solid State Ignition
Spark Plug Cover
Screw, Torx T-15, 10-24 x 15/16"
Cam Bushing
Ground Wire
Cylinder Head Gasket
Cylinder Head
Exhaust Valve (Std.) (Incl. 151)
Intake Valve (Std.) (Incl. 151 )
Screw, 5/16-18 x 1-1/2"
Resistor Spark Plug (RJ19LM4)
Valve Spring
Valve Spring Cap
Intake Valve Seal
MODEL:143.014502
Ref.
No.
Part
No.
169
172
174
178
182
184
185
186
189
191
195
207
216
223
224
236
239
241
245
250
260
261
262
275
277
285
287
290
292
298
300
301
305
306
307
309
310
313
370A
370C
370K
370R
380
390
*36783
36784
30200
29752
6201
*26756
36785
32653
650839
36559A
610973
34336
33086
650451
*36786
650932
*34338
35797
35066
35065
36980
30200
650831
36790A
650988
35000A
650926
29774
26460
28763
36916
36246
35647
*36996
35499
650562
35648
34080
36261
37318
36695
37317
640262
590737
400
416
37029A
36085
417
900
650821
900
Part Name
Valve Cover Gasket
Valve Cover
Screw, 10-24 x 9/16"
Nut & Lock Washer, 1/4-28
Screw, 1/4-28 x 7/8"
Carburetor To Intake Pipe Gasket
Intake Pipe
Governor Link
Screw, 1/4-20 x 3/8"
S.E. Brake Bracket (Incl. 195)
Terminal
Throttle Link
R.P.M Adjusting Lever
Screw, 1/4-20 x 1"
Intake Pipe Gasket
Screw, 10-32 x 49/64"
Air Cleaner Gasket
Air Cleaner Collar
Air Cleaner Filter
Air Cleaner Cover
Blower Housing
Screw, 10-24 x 9/16"
Screw, 1/4-20 x 1/2"
Muffler
Screw, 1/4-20 x 2-5/16"
Starter Cup
Screw, 8-32 x 21/64"
Fuel Line
Fuel Line Clam#
Screw, 10-32 x 35/64"
Fuel Tank (Incl. 292 & 301)
Fuel Cap
Oil Fill Tube
"O"-Ring
"O"-Ring
Screw, 10-32 x 1/2"
Dipstick
Spacer
Lubrication Decal
Primer Decal
Starter Decal
Warning Decal
Carburetor (Incl. 184)
Rewind Starter
(NOTE: This engine could have
been built with 590694 starter).
Gasket Set (Incl. Items Marked *)
! Spark Arrestor Kit (Incl. 417)
(Optional)
Screw, 10-32 x 1/2" (Optional)
Replacement Engine 750830C,
order from 71-999
Replacement Short Block 750806B,
order from 71-999
*Indicates Parts Included in
Gasket Set, Ref. No. 400.
RPM High 2900 to 3200
Page 8
181-1248-11
CARBURETOR
NO. 640262
Ref. _Ref.
No.
1
2
4
5
6
7
16
17
18
20
20/
25
27
28
29
30
31
35
38
36_
37
40
44
47
48
60
\20A
_EWIND
STARTER
13
640262
631615
631767
*631184
!'631183
Part Name
Carburetor (Incl. 184 of Engine Parts Lie:
Throttle Shaft & Lever Assembly
Throttle Return Spring
Dust Seal Washer
Dust Seal (Throttle)
640070
Throttle Shutter
*650506
Shutter Screw
631807
Fuel Fitting
651025
Throttle Crack Screw/Idle Speed Screw
630766
Tension Spring
640018
Idle Restrictor Screw
640200
Idle Restrictor Scrwe Cap (Black)
631867
Float Bowl
*631024
Float Shaft
632019
Float
*631028
Float Bowl "O" Ring
*631021
Inlet Needle, Seat, & Clip (Incl. 31)
631022
SpringClip
640259
Primer Bulb/Retainer Ring
640080
Main Nozzle Tube
632766
Carburetor Tube
*632547
"O" Ring, Main Nozzle Tube
640175
High Speed Bowl Nut
"27110A
Bowl Nut Washer
*630748 ! Welch Plug, Idle Mixture Well
*631027
Welch Plug, Atmospheric Vent
632760B
Repair kit (Incl. Items Marked *)
NO. 590737
Ref.
No.
/
No.
12
_
Part
No.
3
6
7
8
11
590737
59O74O
59O616
590617
590618A
590687A
12
590535
13
14
590701
590760
Part Name
Rewind Starter
Retainer
Starter Dog
Dog Spring
Pulley & Rewind Spring Ass'y
Starter Housing Ass'y (40 degree
grommet)
Starter Rope (Length 98" x 9/64"
clia.)
Starter Handle
Spring Clip
--8
!i
11--7
Page 9
181-1248-11
STARTER
NO. 590694
12
\
/
=;--7
Bb
PaN
No.
No.
PaN Name
590694
Recoil Starter
1
2
3
4
5
6
7
8
11
590599A
590600
590696
590601
590697
590698
590699
590700
590695
12
13
590535
590701
Spring Pin (Incl. 4)
Washer
Retainer
Washer
Brake Spring
Starter Dog
Dog Spring
Pulley & Rewind Spring Ass'y,
Starter Housing Ass'y. (40 degree
grommet)
Starter Rope ( 98" x 9/64" dia.)
Starter Handle
11
13
O
Ref.
4
5
Page 10
181-1248-11
How to ORDER Repair Parts
SEARS
operator's
manual
MODEL
SOLID
The Model Number can be found on a decal on the blower
housing (See Figure 1). Always mention the Model Number
when requesting service or repair parts for your Craftsman
Engine.
All parts listed herein may be ordered from any SEARS,
ROEBUCK AND CO. or SEARS CANADA, INC. retail or catalog
store. If the parts you need are not stocked locally, your order
will be electronically transmitted to a Sears Repair Parts
Distribution Center for expedited handling.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION AS SHOWN IN THIS LIST.
1.
The PART NUMBER
2.
The PART DESCRIPTION
3.
The MODEL NUMBER
4.
The NAME OF ITEM - ENGINE
NO. 143.014502
STATE IGNITION
CAUTION:
Read RULES for
Safe OPERATION
and INSTRUCTIONS
Carefully
Sold by SEARS,
"Your Sears merchandise has added value when you consider that Sears has
service units nationwide staffed with Sears trained technicians.., professional
technicians specifically trained on Sears products, having the parts, tools and
equipment to insure that we meet our pledge to you ... we service what we sell."
ROEBUCK
and SEARS CANADA,
AND CO., CHICAGO,
INC., TORONTO,
IL 60684 U.S.A.
ONTARIO,
CANADA
181-1248-11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 12 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Aug 14 10:42:58 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools