Craftsman 20057933 Sears20170406 User Manual GARAGE DOOR OPENER Manuals And Guides 1705089L

User Manual: Craftsman 20057933 20057933 CRAFTSMAN GARAGE DOOR OPENER - Manuals and Guides View the owners manual for your CRAFTSMAN GARAGE DOOR OPENER #20057933. Home:Garage Door & Opener Parts:Craftsman Parts:Craftsman GARAGE DOOR OPENER Manual

Open the PDF directly: View PDF .
Page Count: 27

Owner’s Manual/Manual Del Propietario

Read and follow all safety rules and operating

instructions before first use of this product.

Fasten the manual near the garage door after

installation.

Periodic checks of the opener are required to

ensure safe operation.

DO NOT install on a one-piece door.

SEOMU01A-1

Write down the Craftsman® serial number located on the garage door opener:

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A

www.craftsman.com

Leer y seguir todas las reglas de seguridad y

las instrucciones de operación antes de usar

este producto por primera vez.

Guardar este manual cerca de la puerta de la

cochera.

Se deben realizar revisiones periódicas del

abridor de puertas para asegurar su

operación segura.

Los dispositivos y funciones automáticas

deben usarse ÚNICAMENTE con puertas

seccionales.

Spanish Section Begins Page: 27

Manual en Español empieza en la pagina: 27

For Residential Use Only

Sólo para uso residencial

GARAGE DOOR OPENER

Abridor de puerta de cochera

MODEL/MODELO 200.57933

Table of Contents

Courtesy light turns on/flashes with audible ‘click’.

(If light bulb is not installed, ‘click’ represents the light)

DO NOT connect power Please connect power

Introduction

Symbols and Icons 2

Inventory 3

Preparation / Tools Required 4

Assembly

Rail and Trolley Assembly 5

Installing the Cable and Chain 6

Mounting Header Bracket 7

Installation

Attaching Rail to Header Bracket and Mounting Door Bracket 8

Mounting Opener to Ceiling 9

Attaching Door Arms 10

Installing Light and Emergency Release Handle 11

Wiring

Wiring Instructions 12

Connecting Photo Eye Safety System 13

Connecting Large Push Button 14

Connecting Power 15

Adjustment

Aligning the Photo Eye Safety System 15

Travel Limit Adjustment 16

Force Adjustment 17

Final Adjustment and Testing 18

Operation

Programming 1 Button Remote 19

Programming Keyless Entry Pad* 20

Operating the Opener 21-22

Maintenance 23

Troubleshooting 23

Repair Parts and Service

Rail Assembly Parts / Installation Parts / Accessories 24

Opener Assembly parts 25

Warranty 26

Symbols and Icons

! WARNING READ WARNINGS CAREFULLY to prevent SERIOUS INJURY or DEATH caused by

electrocution or mechanical hazard.

Installation hardware

— Door arms / Mounting Opener

Inventory

x 2

Clevis Pin — Pulley

3/8” x 1-3/4”

Hitch Pin — Locking Clevis Pins

x 4

Lag Screw #12 x 1”— Photo Eye System

Lag Screw 5/16” x 1-1/2”

— Header Bracket / Mounting Opener

Bolt 5/16” x 1”

Drywall Anchor

- Large Push Button

x 2

Screw #6 x 1”

- Large Push Button

x 30

5/16” Flange Nut

x 4 x 4

x 4

x 1

Emergency Release Knob + Rope

Literature + Safety Labels

Chain

Photo Eye Safety System

Opener Unit + Light Lens Cover

Sprocket Cover

Header

Bracket

Door Bracket

Trolley

Door Arms

Pulley

Rail — Header Segment

Rail — Middle Segments x3

INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE)

Hanging

Brackets

Insulated Staples

— Securing wires

x 2

Self-Threading Screw 1/4” x 5/8”

Door Bracket

Trolley Shaft

and Cable

Master Link Set

—Trolley Shaft

x 1

Rail — End Segment with Trolley Stop Bolt

Clevis Pin — Door arms

5/16” x 1”

Clevis Pin — Header Bracket

5/16” x 1-1/2”

1-Button

Remote Push Button

OPTIONAL

3-Button Mini

Remote*

Keyless Entry Pad*

Drywall Anchor

x 2

Screw #6 x 1”

OPTIONAL

*See Accessories in Repair Parts section of this manual for purchase information.

Preparation

Level

Tape Measure

Hack Saw

Pencil

Drill, 3/16” and 5/16” Drill Bits

Tools Required

Step Ladder

Screwdriver

Hammer

Sectional Garage Door BEFORE beginning Installation:

1. Disable locks and remove all ropes connected to the

garage door.

2. Perform the following door test to ensure your door is

balanced and in good working condition.

To Test Your Garage Door

1. Raise and lower the door to check if there is any sticking or

binding.

2. Check for loose hinges, damaged rollers, frayed cables and

damaged or broken springs.

3. Lift the door approximately halfway and release. The door

should stay at the point under proper spring tension.

Call a qualified garage door service technician if your door binds,

sticks or is unbalanced.

! WARNING

To prevent SERIOUS INJURY or DEATH:

- Before beginning installation of the opener please complete the following test to ensure that your door is

balanced and in good working condition.

- A poorly balanced door can cause serious injury and damage to the opener.

- Always have a qualified garage door service technician make any required adjustments and/or repairs to

your door before proceeding with installation.

- DISABLE ALL LOCKS and REMOVE ALL ROPES connected to the garage door BEFORE installing

and/or operating the opener.

To prevent damage to the door and opener:

- DO NOT connect power until instructed.

- Operate this opener with AC 120V/60Hz power supply ONLY.

Pliers

Adjustable Wrench Ratchet with

5/16”, 7/16” and 1/2” sockets

DO NOT REUSE PARTS FROM ANOTHER BRAND OF OPENER!!!

Rail and Trolley Assembly

Opener

Trolley direction (Top View)

Clevis Pin

Pulley

Hitch Pin

Clevis Pin — 3/8” x 1-3/4”

Hitch Pin

Connect shaft to Trolley with “click”

To Assemble Rail and Opener

1. Prepare the rails as shown in Fig.1.

2. Connect the rails starting with the header segment. Insert

the tapered ends into open ends, apply any additional force

necessary by tapping the rail on padded flooring. Ensure

the end segment has trolley stop bolt facing up. Make sure

the rails are securely joined together as shown.

3. Slide the trolley onto the rail from the header segment.

Make sure the arrow is pointing towards the door as shown

in Fig.1.

4. Connect the rail assembly to the rail bracket on the opener.

To Assemble the Header Section of Rail

Follow steps shown in Fig.2:

1. Remove the “trolley shaft and cable” from the chain carton

and lay it beside the rail assembly. Hold cable eyelet on the

end of cable and thread about 20” (50cm) through the slot

on the Header Segment of the rail.

2. Insert the pulley into the opening while the cable is hanging.

3. Secure the pulley by inserting the 3/8” x 1-3/4” clevis pin

through the top of the rail.

4. Lock the clevis pin with a hitch pin. Rotate the pulley to

ensure it spins smoothly.

Refer to Fig.3 to connect the trolley shaft to the trolley. Slide both

the trolley shaft and trolley towards each other. A “click” will be

heard when they are connected.

To Link Cable with Chain

Refer to Fig.4. Place the chain carton beside the rail, hold the

“chain to cable connector” and pull about 8” (20cm) of chain from

the box. Thread the chain to cable connector onto the trolley

shaft so that they are loosely linked together.

Fig.1

Fig.2

Fig.4

Fig.3

! CAUTION

- DO NOT connect power until instructed.

- To prevent INJURY, keep hands and fingers

away from joints and possible sharp edges.

- Wear gloves when installing chain and cable.

Rail Bracket

Trolley Shaft

Trolley Shaft Trolley

Cable Eyelet

Loosely link together

Trolley Shaft Chain-to-Cable Connector

Chain

When connecting the rails ensure they are securely connected as shown above.

To apply additional force tap gently on the end of the rail with a rubber mallet*.

*Only use a soft rubber mallet to tap on the end of the rails as other tools may damage your rail.

Rail — Header Segment

Rail — Middle Segments

(tapered) x 3

Rail — End Segment (tapered)

with Trolley Stop Bolt

DOOR

If the supplied chain and rails are not long enough for your installation, you may purchase an 8-foot or 10-foot Chain Drive

Extension Kit. To purchase a kit, visit a Craftsman outlet ,call 1-888-331-4569,or go online to www.craftsman.com

To Install Chain

1. Pull the remaining chain along the rail toward the opener.

2. A segment of chain marked in RED will be seen. Place this

segment in the approximate location on the sprocket as

shown in Fig.1.

3. When the chain is aligned properly around the sprocket, pull

the chain-to-cable connector towards the trolley shaft.

Follow steps shown in Fig.2 to connect & tighten the chain:

1. Align the open end of the chain to the cable eyelet and

connect together using the master link set.

2. Turn the chain-to-cable connector on the trolley shaft until

the chain is about 1/4” (6mm) above the base of the rail.

Compare with the illustration below.

3. Tighten the flange nut on trolley shaft against the chain-to-

cable connector.

When the chain and cable are tightened around the rail and

sprocket on the opener, check and make sure the chain is

properly aligned and not twisted. Attach the sprocket cover to the

opener as shown in Fig.3.

Notice

During operation, it is normal for the chain to appear loose when

the door is closed. If the chain returns to the position as shown

below when the door is opened, the chain is adjusted properly.

DO NOT re-tighten the chain.

When performing maintenance, always PULL the emergency

release to DISCONNECT the door from opener before adjusting

the chain.

Installing Cable and Chain

! WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers clear from sprocket during operation.

- Wear gloves when installing chain and cable.

- Keep hands and fingers away from joints and possible sharp edges.

Cable

Chain

Fig.1

Fig.2 Fig.3

Sprocket

Cover

Tighten until... 1/4” (6mm)

Base of Rail

Mid-point of rail assembly

Tighten nut

Flange Nut

Master Link

Link Cap

Spring Clip

Cable Eyelet

Open end of chain

Chain to Cable Connector

To Connect and Tighten the Chain:

Sprocket

Rail Bracket

Chain

Top of Rail

Chain in RED

Actual Size

Clevis Pin

Hitch Pin

To Install Header Bracket

Note: Installation procedures may vary according to door

type.

1. While inside your garage, close the door and mark the

vertical centerline of the garage door. Extend the line onto

the header wall above the door spring.

2. Open the door to the highest point of travel. Mark a line on

the header wall 2“ (5cm) above the highest point of travel.

Note: DO NOT install the header bracket over drywall. In some

installations, it may be necessary to install a 2x4 across two wall

studs to create a suitable location for the header bracket.

If installing into masonry, use concrete anchors (not provided).

Wall-Mounting

As shown in Fig.2, place the header bracket on the vertical

centerline in direction shown.

Mark and drill two 3/16” holes. Fasten the header bracket

securely to a structural support using two 5/16” x 1-1/2” lag

screws.

Alternative Ceiling-Mounting

Ceiling-mounting is suggested ONLY when clearance is minimal.

Extend the vertical centerline onto the ceiling as shown in Fig.3.

center the header bracket on the vertical mark, no more than

6” (15cm) from the header wall. Mark and drill holes to fasten the

header bracket securely to a structural support.

Mounting Header Bracket

OPENER

MAX. 6” (15cm)

Highest Point of Door Travel

Vertical Centerline

Horizontal Line

Finished Ceiling

Lag Screw

5/16” x 1-1/2”

! WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- The header bracket MUST be SECURELY fastened to the structural support on the mounting wall or

ceiling, otherwise the door may not reverse when required. DO NOT install the header bracket over drywall.

- Concrete anchors MUST be used when mounting the header bracket into masonry.

- NEVER try to loosen, move or adjust garage door springs, cables, pulleys, brackets, or hardware.

- Contact a qualified garage door service technician if your door binds, sticks or is unbalanced. An unbal-

anced door might not reverse when required.

Vertical Centerline

Fig.2 (Wall-Mounting) Fig.3 (Ceiling-Mounting)

7FT door

8ft max

8FT door

9ft max

Fig.1

Ceiling

Header Bracket

Header Wall

2” (5cm) clearance

Door Track

Door

Highest Point of Door Travel

Support block on floor

Door Spring

* VERY IMPORTANT! *

Max recommended rail height from floor

 7ft door = 8ft max height

 8ft door = 9ft max height

MAX RAIL HEIGHT

Floor

Attaching Rail to Header Bracket and Mounting Door Bracket

! CAUTION

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- REINFORCEMENT is recommended for fiberglass, aluminum or lightweight steel garage doors BEFORE

installing the door bracket. Contact your door manufacturer for reinforcement options.

Fig.1

Fig.2 Fig.3

Carton

Clevis Pin - 5/16” x 1-1/2”

Hitch Pin

Self-Threading

Screw - 1/4” x 5/8”

Vertical Centerline of Door

(a) (b) (c)

2-4” (5-10cm)

Top Edge of Door

To Attach the Opener to the Header Bracket

1. As shown in Fig.1, use the packaging carton as temporary

support for the opener. Place the opener on carton to

prevent damage.

2. Align the mounting hole on the header rail to the mounting

hole on the Header Bracket.

3. Connect the header rail and the door bracket together with

a 5/16” x 1-1/2” clevis pin and lock it in place with a hitch

pin.

To mount the Door Bracket

Note: Some door reinforcement kits may provide direct

attachment of the door arm to the reinforcement bracket. If you

have a door reinforcement bracket with this option, skip this step

and proceed with the next step “mounting opener to ceiling”.

1. Position the door bracket on the centerline of the door

approximately 2” - 4” (5-10cm) below the top edge of the

door, as shown in Fig.2.

2. Depending on the construction of your door, install using

one of the steps shown if Fig. 3 below:

For steel / lightweight doors with vertical steel

reinforcements / factory reinforced.

(a) Mark and drill two 3/16” holes. Make sure not to drill

through the garage door. Secure the door bracket with two

1/4” x 5/8” self-threading screws (provided) as shown in

Fig.3(a).

(b) Alternative installation: Drill two 5/16” holes through the

door. Secure the door bracket using two 5/16” bolts, lock

washers and nuts (not provided) as shown in Fig.3(b). The

length of bolts will depend on the thickness of your door.

Wood door

Secure the door bracket using two 5/16” carriage bolts,

washers and nuts (not provided) as shown in Fig.3(c). The

length of bolts will depend on the thickness of your door.

Note: DO NOT use Self-Threading Screws on a wood door.

To Mount the Opener to Ceiling

The three most common installation options are shown in

Fig.1-3.

Fig.1 shows mounting the opener directly to structural

support on the ceiling. Fig.2 and 3 show mounting on a

finished ceiling, with heavy duty angle iron*.

*(angle iron not included)

Determine the mounting option that works best for your

application and follow installation steps below:

1. Raise the opener and rail assembly and temporarily place it

on a stepladder.

2. Position the opener and rail assembly so that it is aligned to

the center line of the garage door. If the header bracket was

mounted off center, align the opener with the header

bracket.

3. Measure the distance from each side of the opener to the

structural supports.

4. Cut both hanging brackets to appropriate length.

5. Drill 3/16” holes in the structural supports.

6. Secure one end of each of the hanging brackets to the

structural supports using 5/16” x1/2” lag screws (provided).

7. Secure the opener to the hanging brackets and secure each

side with a 5/16” x 1” bolt and flange nut (provided).

8. Move the door manually to check clearance between

highest point of travel of the door and rail. If the door hits the

rail, raise the header bracket or adjust the mounting of

opener.

9. Remove the ladder ONLY when the opener is securely

mounted to the structural supports.

Mounting Opener to Ceiling

! WARNING

To prevent SERIOUS INJURY or DEATH:

- DO NOT connect power until instructed.

- Install the opener at least 7 feet (2.13m) above the floor.

- Fasten the opener SECURELY to STRUCTURAL SUPPORTS of the garage to prevent falling.

- If installing brackets to masonry, concrete anchors (not provided) MUST be used.

Fig.1

Fig.2

Fig.3

Lag Screw 5/16” x 1-1/2”

Bolt 5/16” x 1”

Flange Nut

Structural support

Finished ceiling

Fastening Hanging Brackets to structural supports

Securing Opener to Hanging Brackets

Bolt / Lock Washer / Nut

not provided

Bolt / Lock Washer / Nut

not provided

Angle Iron not provided

Attaching Door Arms

! WARNING

To prevent SERIOUS INJURY:

- DO NOT connect power until instructed.

- Keep hands and fingers away from the sprocket during operation.

- Wear gloves when installing chain/belt and cable.

- Keep hands and fingers away from joints and possible sharp edges.

Clevis Pin - 5/16” x 1”

Hitch Pin

Bolt 5/16” - 18x1”

Flange Nut

Curved Door Arm

Straight Door Arm

1 2

Fig.1

Min. 8” (20cm) NOTE: The trolley must be a minimum of 8” (20cm) away

from the pulley.

To Connect Door Arm

Follow the steps shown in Fig. 1

1. Fasten the straight door arm to the trolley with a

5/16” x 1” clevis pin and lock it with a hitch pin.

2. Fasten the curved door arm to the door bracket with

5/16” x 1”clevis pin and lock it with a hitch pin.

3. To connect the door arms together, choose two pairs of

holes which are as far apart as possible. Fasten the arms

using two 5/16” x 1” bolts and flange nuts.

2” or less 2” or more

Rail of Opener

Door Panel

Rail of Opener

Door Panel

Correct Spacing Incorrect Spacing

Installing Light and Emergency Release Knob

To install the light:

1. Insert screw driver between lens and the cover at the

detents, pry and pull the light lens cover from the top and

detach it from the opener.

2. Install a standard A19 (E26) 100 watt maximum light bulb.

3. Re-attach the light lens cover.

Notice

When replacing the light bulb, make sure the bulb on the opener

has cooled down to prevent injury.

! WARNING

To prevent SERIOUS INJURY or DEATH from electrocution:

- Disconnect power cord before installing/replacing light bulb.

To prevent possible OVERHEATING or damage to opener:

- Use ONLY A19 (E26) incandescent bulbs* (100W max.).

- DO NOT use short neck or specialty light bulbs.

- DO NOT use halogen bulbs.

* CFL or LED light bulbs will work but may interfere with hand-held remotes.

6 feet (1.83m) above floor

To attach the Emergency Release Knob:

1. Thread one end of the rope through the hole of the

emergency release Knob and secure with an overhand

knot.

2. Thread the other end of the rope through the hole in the

trolley lever.

3. Measure the rope length so that the knob is 6 feet (183cm)

above the floor and is clear from the top of your vehicle.

Secure with a overhand knot.

Fig. 1

Fig. 2

! WARNING

To prevent SERIOUS INJURY or DEATH from a falling garage door:

- In case of power failure or door obstruction, PULL EMERGENCY HANDLE to release door from opener.

- When emergency release is in the released position, the door can be operated manually.

- To reconnect, flip the lever on the trolley towards opener, back to connect position, it will reconnect

automatically upon pressing wall panel or remote control.

- DO NOT use emergency handle to pull the door open or closed.

Lever

Emergency Release Knob

Light Lens Cover

* VERY IMPORTANT! *

Emergency release knob must clear all vehicles. An

Emergency release knob set too low may get caught by

the vehicle and cause damage to the opener. Measure

from the floor to the top of your vehicle and set the

emergency release knob above this measurement.

100W MAX

Wiring Instructions

Photo Eye Safety System

Wires to the terminals on the opener

Terminals

In the following section, the photo eye safety system and

large push button will be connected to the opener. Please

read and understand the wiring instructions before

connecting wires.

1. Remove the pre-cut skin on the open end of wire from

accessories. Wires MUST NOT be frayed. Wires must be

connected as shown in Fig.1.

2. To connect a wire to an assigned terminal, use a small “flat

head” screwdriver to push in the orange tab on the Wire

terminal as shown in Fig.2.

3. Insert approximately 1/2” (13mm) of the wire into the

terminal while pushing in the tab as shown in Fig.2.

4. Each accessory requires a pair of terminals. Each pair of

terminals MUST be connected with one white wire and one

striped wire (non-polarized) from the SAME accessory as

shown in Fig.2.

5. Check for proper connection by gently pulling on the wire.

The wire should not come out of the terminal. NO exposed

part of the wire should be visible outside of the terminal.

6. Use the insulated staples provided to secure the wires to

the wall and/or ceiling. Be careful not to damage the wires

while securing the staples.

! WARNING

To prevent SERIOUS INJURY or DEATH from electrocution:

- Power MUST NOT be connected until instructed.

- NO exposed part of the wire should be visible outside of the terminal for proper connection.

Suggested placement of insulated staples

Fig. 2

Fig. 1

Wire from accessories

Remove and discard pre-cut skin

Right Wrong

* VERY IMPORTANT! *

Screwdriver or similar tool

Wire Terminals

Open

Insert into unit Outside

Wire shown in actual size

1/2”

Push In

Connecting Photo Eye Safety System

About the Photo Eye Safety System

The photo eye safety system provides protection against

entrapment while the door is closing. When properly connected

and aligned, the emitter photo eye emits an invisible infrared

light beam while the sensor photo eye monitors that beam.

If the beam is obstructed during door-closing, the entrapment

protection will be triggered and the door will stop and reverse to

the open position. The courtesy light will flash for 30 seconds

indicating an obstruction.

Installing The Photo Eye Safety System

Wall-mounting

1. Place the photo eyes facing each other on each side of

the garage door. Position the sensors so they are no

higher than 6” (15cm) above the floor, as shown in Fig.1.

2. Drill 3/16” holes using the mounting holes on the bracket

as a template. Secure with #12 x 1” lag screws

(provided).

3. Be sure brackets, when mounted, are NOT in contact with

the door track.

4. If necessary use the optional wall-mount position (Fig.1)

to better fit your door-track and improve obstacle

avoidance. To adjust the position, loosen the wing nut,

disassemble the bracket and move the photo eye to the

lower position on the holder.

5. If necessary, align the photo eyes by loosening the wing

nut . (This step may be further required in Aligning the

Photo Eye Safety System on page 15.)

Alternative Floor-mounting

1. Place the photo eyes facing each other on each side of the

garage door, as shown in Fig.2.

2. If attaching to concrete, secure the photo eyes using

concrete anchors and bolts (not provided).

3. Be sure brackets, when mounted, are NOT in contact with

the door track.

4. If necessary, align the photo eyes by loosening the wing

nut. (This step may be further required in Aligning the

Photo Eye Safety System on page 15.)

To Connect Photo Eye Safety System

1. Connect a pair of wires from either one of the photo eyes

to a pair of “PHOTO EYE” terminals on the rear of the

opener as shown in Fig. 3. Refer to Wiring Instructions

on page 12 for proper connections.

2. Repeat above step to connect the other photo eye.

3. Refer to Wiring Instructions on page 12 to ensure wires

are connected properly.

! WARNING

To prevent SERIOUS INJURY or DEATH from electrocution:

- Power MUST NOT be connected BEFORE photo eye safety system is connected and aligned.

- The opener will not operate until the photo eye safety system is properly connected and aligned.

- Install the photo eyes NO higher than 6” (15cm) above the floor.

No part of garage door or other objects should obstruct the photo eye safety system during door-closing.

Fig. 1 (Wall Mount)

Fig. 3

6” max.

Optional

wall mount

position

Inside

Garage

From one of

the Photo Eye From the

other one

#12 x 1”

Lag Screw

Loosen

Inside

Garage

Door Track

6” max. above floor

Alignment

Inside

Garage

Door Track

To Connect the Push Button to the Opener

Connect the pair of wires from the push button to the pair of

“PUSH BUTTON” terminals on the rear of the opener. Refer to

Wiring Instructions on page 12 to ensure wires are properly

connected.

The push button is a wired, illuminated door control placed

inside your garage.

To install the Push Button:

1. Inside your garage, install push button within sight of the

door at a minimum height of 5 feet (1.5m) off the ground.

Ensure it is installed out of the reach of children and free

from the moving parts of the door and hardware.

2. Securely fasten it to a solid surface with 1” screws. If

attaching to drywall or other hollow surface, drill 3/16”

holes and use the provided drywall anchors.

To prevent SERIOUS INJURY or DEATH from electrocution:

- Power MUST NOT be connected until instructed.

To prevent SERIOUS INJURY or DEATH from using the push button and a closing door:

- Install the push button within sight of the door at a minimum height of 5 feet (1.5m) above the floor.

Make sure it is out of the reach of children and moving parts of door and hardware.

- NEVER permit children to access the push button or remote controls.

- Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight.

- ALWAYS keep a moving door in sight until it’s completely closed.

- NEVER cross the path of a moving door.

Push Button

Min. 5 feet (1.5m)

above floor

From Push Button

Connecting Push Button

! WARNING

Drywall Anchor

Screw #6 x1-1/4

NOTICE: Only use the Push Button included with this GDO model or identical replacement part. See

Accessories in Repair Parts section of this manual.

Connecting Power

Aligning the Photo Eye Safety System:

1. When power is supplied, the green photo eye (Emitter) will flash

until it is aligned with the red photo eye (sensor). The red photo

eye will not light until it is aligned with the green eye.

2. When the photo eye system is properly aligned the green photo

eye (emitter) will emit a steady green light and the red photo eye

(sensor) will emit a steady red light.

3. If either of the photo eye lights are unsteady, flash or dim, check

for an obstruction and carefully adjust the position of the photo

eyes until they give a steady green light and steady red light.

Note: The path of the invisible light beam MUST NOT be

obstructed. No part of the garage door or any hardware

should interfere or block either sensor.

Aligning the Photo Eye Safety System

! WARNING

To prevent SERIOUS INJURY or DEATH from electrocution or fire:

- Power MUST be DISCONNECTED BEFORE proceeding with permanent wiring procedures.

- Garage door opener installation and wiring MUST be in compliance with all local electrical and building

codes. Make sure the opener is ALWAYS grounded.

- NEVER use an extension cord, 2-wire adapter or modify the power plug in any way to make it fit the outlet.

Ordinary Power Connection

WARNING

To prevent SERIOUS INJURY or DEATH from a closing garage door:

- The photo eye safety system MUST be installed BEFORE connecting power.

- The photo eye safety system MUST be properly connected and aligned BEFORE operating the opener.

NOTICE: The opener will not close until the photo eyes are installed. Photo eyes are required by federal law to

be installed on all openers.

Invisible Light Beam

The emitter

generates the

invisible light

beam

The sensor

receives the

invisible light

beam

Steady Red &

Green light

For Permanent Wiring ONLY

Conduit with wire

Yellow (from Motor)

White (from Light)

Neutral (White)

Wire nut (Not provided)

White

(from Logic Board)

Line (Black ) Ground (Green/Yellow)

Black (from Logic Board)

Ground Screw (Green)

DO NOT OPERATE OPENER AT THIS TIME.

To Connect Power

Plug the opener into a grounded outlet ONLY. If there is no

grounded outlet present, call a qualified electrician to replace the

outlet. Use of a surge protector is highly recommended page 4.

Permanent Wiring (If Required by Local Code)

1. Remove the enclosure by removing the 6 screws located

on the sides and rear of the opener.

2. Cut the two cable pressure connectors connecting line

(black) and neutral (white) wire from the power cord.

3. Remove the grounding screw connecting the green wire.

4. Remove the power cord.

5. Group neutral (white) wires from power source with 2 white

wires from light cable, and logic board, and yellow wire

from motor, inside the opener. Connect them with a wire

nut.

6. Group line (black) wires from power source with another

black wires from logic board inside the opener. Connect

them with a wire nut.

7. Secure the ground (green or bare) wire from the power

source with a grounding screw.

8. Reinstall the enclosure.

9. Turn on power supply. If the wiring is properly connected, a

“click” should be heard and the light will illuminate (if a bulb

is installed). If there is no response from the opener, check

power source and wiring.

About Travel Limits

Limit adjustments regulate the position at which the door will

stop when opening and closing.

BEFORE making any adjustments, operate the door by using

the large push button or remote. Run the opener through a

complete cycle.

If the door opens and closes completely without unintended

reversing upon closing — NO adjustment is necessary.

If the door does not open or close at desired positions, proceed

with the instructions below to adjust the travel limits.

Adjusting Travel Limits

Open and close limits can be increased (+) or decreased (-) by

turning the corresponding screws on the opener. Use a “flat

head” screwdriver to make adjustments. One full turn of the

screw is about 2” (5cm) of actual travel.

NOTE: The opener motor includes an automatic thermal

protection system which will shut down the motor in an overheat

situation. The thermal protector will reset itself once the motor

cools down. Opening and closing the opener multiple times (in a

short period of time) may cause the motor to overheat and shut

down. If this happens, wait about 15 minutes for the motor to

cool and retry operation.

Setting OPEN (UP) Travel Limit

1. CLOSE the garage door by using either the remote or

large push button .

2. Adjust the OPEN limit screw.

3. OPEN garage door and check for proper adjustment.

4. Repeat steps 1-3 until the door opens to the desired

position. When the door is in the open position, make sure

there is enough clearance for your vehicle(s), and there is

a minimum 2“ (5cm) gap between trolley and stop bolt.

5. Perform Safety Reverse Test on page 18.

If the door does not open past 5 feet (1.5m), follow Force

Adjustment on page 17 to adjust the open force.

Setting CLOSE (DOWN) Travel Limit

1. OPEN the garage door by using either the remote or large

push button .

2. Adjust the CLOSE limit screw.

3. CLOSE the garage door and check for proper adjustment.

4. Repeat steps 1-3 until door closes to the desired position.

5. Perform Safety Reverse Test on page 18.

Travel Limit Adjustment

! WARNING

To prevent SERIOUS INJURY or DEATH from improper force adjustment:

- Improper adjustment of travel limits will cause operation of safety reversal mechanism.

- If travel limit adjustment is made, force adjustment may also needed.

- After ANY adjustments, the safety reverse test MUST be performed to ensure the door reverses on

contact with a 1-1/2” thick object (2x4 laid flat).

If the door reverses unintentionally during

closing, check below symptoms:

1. The photo eye system may be improperly

connected, misaligned or obstructed The

courtesy light will flash continuously for 30

seconds. Refer to Troubleshooting on P.22.

2. Binding door — disconnect the door from the

opener by using the emergency release

handle. Open and close the door manually

and check the following steps.

2.1 If the door is balanced, refer to Force

Adjustment on Page17 to adjust Close

force.

2.2 If the door is unbalanced, binding or

jammed, call a trained service person to

adjust the door.

Adjusting Open (Up) Travel Limit

Adjusting Close (Down) Travel Limit

Stop Bolt

Trolley

Minimum 2” (5cm) clearance

Open

Adjusting Force

1. Force adjustment controls are located on the rear panel of

the opener. The force adjustments regulate the amount of

force required to open or close the door.

2. Force adjustment is applied only to compensate for the minor

resistance caused by weather or other means.

 Note: Force is preset at level 6 for both open and close

adjustments. The size and operating conditions of the

garage door will determine the correct level of force/

sensitivity. Weather conditions may also affect the operation

of the door requiring further adjustments as needed.

 Note: If the close force is set too light the opener will reverse

the door during closing. If the open force is set too light the

opener will stop the door during opening.

 Note: There are 12 levels for open and close force settings.

When either the maximum or minimum level is reached, the

light will flash 6 times.

 Never adjust the force setting by more than 1 level (1 press)

at a time.

Setting Force

Setting Close Force

1. If the door completes a full close cycle without reversing,

decrease (-) the close force by 1 level at a time until the door

reverses. If the door reverses during closing, increase (+)

close force by 1 increment. The close force is now properly

adjusted.

2. During the ”door-close” cycle, the opener will reverse if the

force required to close the door is exceeded.

Setting Open Force

1. If the door completes a full open cycle without stopping,

decrease (-) the amount of force by 1 level until the door

stops during the opening. Once the door stops during

opening, increase (+) open force by 1 increment. The close

force is now properly adjusted.

2. During the “door-open” cycle the opener will stop if the force

required to open the door is exceeded.

Force Adjustment

! WARNING

To prevent SERIOUS INJURY or DEATH from improper force adjustment:

- DO NOT adjust force to compensate for binding or sticking of the garage door. Call a qualified garage

door service technician to make necessary adjustments in case of binding.

- DO NOT increase the force beyond minimum force required for closing the door. Too much force will cause

improper operation of safety reversal mechanism.

- If either the force or travel limit adjustment is made, the other adjustment may also needed.

- After ANY adjustments, the safety reverse test MUST be performed to ensure the door reverses on

contact with a 1-1/2” thick object (2x4 laid flat) .

For safe operation, the force setting should

always be set at the MINIMUM FORCE

required to run the door.

Testing the Safety Reverse System

The Safety Reverse System prevents the door from closing

when an obstruction is present.

1. Open the door by using the large push button or remote

2. Place a 1-1/2” (3.8cm) thick solid object (or 2x4 laid flat)

on floor under the center of garage door.

3. Keeping the door in sight, use the large push button or

remote to close the door.

4. The door MUST REVERSE upon striking the object within

1.5 seconds, and stop at the fully opened position.

5. The courtesy light will start flashing for 30 seconds upon

triggering the Safety Reverse System.

If the door just stops on the object, adjust the opener as follows:

The close travel maybe inadequate, Increase close travel limit

by 1/4 turn (See Limit Adjustment on page 16)

Conduct the test again. If the door reverses on contact, remove

the object and run at least 3 COMPLETE travel cycles to ensure

proper adjustment.

If the door still does not reverse on the object, decrease the

close force (see Force Adjustment on page 17) and repeat the

test.

If the opener still fails the safety reverse test, call a qualified

technician for door adjustment.

Testing the Photo Eye Safety System

1. Open the door by using the large push button or remote

2. Make sure both photo eyes steadily emit the green and

red indicator lights. (If not, check alignment)

3. Place an object under the door about 8” (20cm) high by

12” (30cm) wide (the opener carton can be used),

4. The red indicator light on the sensor eye should be

dimmed.

5. Keep the door in sight and use the large push button or

remote to try to close the door.

6. The door should NOT move more than 1” (2.5cm) and the

courtesy light should flash for 30 seconds.

Final Adjustments and Testing

! WARNING

To prevent SERIOUS INJURY or DEATH from a closing garage door:

- The Safety Reversal Test MUST be conducted ONCE A MONTH.

- NO ONE should cross the path of moving door during operation and/or testing.

- If either force or travel limit adjustment is made, the other adjustment may also needed.

- After ANY adjustments to the door system, the Safety Reverse Test MUST be performed to ensure the

door reverses on contact with a 1-1/2” thick (2x4 laid flat) object.

- The photo eye safety system MUST be properly aligned, and tested regularly.

1-1/2” (3.8cm) thick solid object (or 2x4 laid flat)

seconds

Programming 1– Button Remote

! WARNING

To prevent SERIOUS INJURY or DEATH:

- Keep remote and battery out of reach of children.

- NEVER permit children to access the wall panel nor remotes.

- Operate the door ONLY when it is properly adjusted, and there are no obstructions present.

- ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.

To reduce risk of fire, explosion or electric shock:

- DO NOT short circuit, recharge, dissemble or heat the battery.

- Replace with 23AE 12 volt batteries ONLY. Dispose of batteries properly.

Visor Clip

Holster

Signal and

Battery Indicator

23AE 12 Volt

Alkaline Battery

To Program Remote(s):

1. See Fig.2 to add a remote. Press the “LEARN” button on

the rear control panel of the opener. The courtesy light will

illuminate with an audible click*. The unit is now ready to

learn a remote.

2. Within 30 seconds, press the button on the remote.

3. The courtesy light will flash twice indicating remote has

been stored successfully**.

Up to 20 remotes (including keyless entry pad codes) can be

added to the unit by repeating the above procedures.

If more than 20 remotes are stored, the first stored remote will

be replaced. (i.e. the 21st remote replaces the 1st stored

remote.)

* If the courtesy light is already on, it will flash once and stay

illuminated for 30 seconds.

** If a remote is not accepted, the courtesy light will stay on for

30 seconds, flash 4 times and then stay on for 2-1/2

minutes. Retry programming the remote by repeating the steps

above.

Removing all Remotes:

To remove all remotes from memory, press and hold the

“LEARN” button for 5 seconds. The courtesy light will flash 7

times indicating all remotes have been removed from memory.

Replacing Remote Battery:

When the battery of the hand held remote is low, the indicator

light will become dim and/or the range of the remote will

diminish. To replace the battery, remove the battery cover from

the remote as shown in Fig 4. Replace with a 23AE 12 volt

alkaline battery with polarity shown in Fig.4.

Fig.1

Fig.2

Fig.4

This device complies FCC rules for HOME OR OFFICE USE. Operation is

subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Fig.3

LEARN

seconds

To purchase a keyless entry pad, visit a Craftsman outlet, call 1-888-331-4569, or go online to www.craftsman.

! WARNING

To prevent SERIOUS INJURY or DEATH:

- Keep remote and battery out of reach of children.

- NEVER permit children to access the wall panel, push button nor remotes.

- Operate door only when it is adjusted properly with no obstructions to door travel and is in clear sight.

- ALWAYS keep a moving door in sight until completely closed. NO ONE should cross the path of a moving door.

To reduce risk of fire, explosion or electric shock:

- DO NOT short circuit, recharge, disassemble or heat battery.

- Replace with 1.5 volt AAA batteries ONLY. Dispose of batteries properly.

To Add Personal Codes:

1. Press the “LEARN” button on the rear control panel, “OK”

LED will glow and beep. The unit is ready to accept a

remote in the next 30 seconds as shown in Fig.1.

2. Enter a 1 - 6 digit personal code on the keyless entry within

30 seconds and press/release “ENTER” button. “OK” LED

will flash and beep twice indicating personal code is stored

in memory.

Up to 20 personal codes (including 1-button remotes) can be

added to the unit by repeating the above procedures.

If more than 20 personal codes are stored, the previously stored

one from the very beginning will be replaced, (i.e. the 21st remote

replaces the 1st stored one.)

Operation:

To access the door, enter a pre-stored personal code and press

“ENTER” to transmit code, and within 20 seconds, "ENTER"

button can be used to stop or reverse the door.

If the code is entered incorrectly, correction can be made by

pressing “ENTER” to reset and re-enter code.

When dark, “ENTER” may be pressed in advance to turn on back

light.

Removing ALL Personal Code(s):

To remove ALL personal code(s) and/or remotes from memory,

press and hold the “LEARN” button for 5 seconds. “OK” LED will

flash and beep, indicating all codes/remotes have been removed

from memory.

Mounting the Keyless Entry:

Keyless entry may be secured on door jamb face outside your

garage. Locate keyless entry within sight of door at minimum

height of 5 feet (1.5m), ensure it is away from reach of children

and moving parts of door and hardware. Test the reception of the

keyless entry before mounting. Change location for better

reception if necessary.

Use the mounting holes on the keyless entry as template to mark

position on the mounting surface. To attach to a wooden surface

use the screws provided. In case of a drywall surface, drill holes

and use drywall anchors provided.

Replacing Keyless Entry Battery:

When the battery of keyless entry is low, dimmed illumination is

observed. To replace battery, remove the battery cover by

loosening the screws underneath, and replace the battery with

two1.5 volt AAA batteries.

Enter a 1- 6 digit personal

code and press/release

“ENTER”

Fig.2

Fig.1

Programming Keyless Entry Pad *

LEARN

seconds

2 3

*Optional

(2) 1.5 Volt AAA

Alkaline Batteries

Operating the Opener

! WARNING

To prevent SERIOUS INJURY or DEATH:

- READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS IN THE OWNER’S MANUAL AND LABELS

- Keep remote and battery out of reach of children.

- NEVER permit children to access the wall panel or remotes.

- Operate the door ONLY when it is properly adjusted, and there are no obstructions and is in clear sight.

- ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.

- If travel limit adjustment is made, force adjustment may also needed.

- After ANY adjustments, the safety reverse test MUST be performed to ensure the door reverses on contact

with a 1-1/2” thick object (2x4 laid flat).

- ALWAYS ensure that your door is balanced and in good working condition.

Controls Operation

Push Button

(Indoor)

Press and hold the push button until the door starts to move, and controls as follows:

- Open or close the door.

- Reverse the door while it is closing

- Stops the door while it is opening.

- Close the door when the photo eye safety system is not installed, misaligned or

obstructed INTENTIONALLY.

1- Button Remote

Same functions* as the push button with remote distance up to 100 ft. in open field.

*For safety concerns, the 1– button remote WON’T work if the photo eye safety

system is not properly installed and aligned.

Keyless Entry Pad * Program the keyless entry pad accordingly and access the door using the PIN code.

3-Button Mini

Remote*

Remote distance up to 100 ft. in open field.

For safety concerns, the hand-held remote WILL NOT work if the photo eye safety

system is not properly installed and aligned.

Activating the Opener

Emergency Release Handle

Photo Eye Safety System

Invisible Light Beam

Push Button

Courtesy Light

Actual Operating Scenario

*Optional

See Accessories in Repair Parts section of this manual for purchase.

! WARNING

To prevent SERIOUS INJURY or DEATH:

- Use emergency release to disconnect trolley ONLY when the door is CLOSED to prevent unexpected rapid falling in

case of a unbalanced / poor-conditioned door.

- Use emergency release ONLY when doorway is clear of persons and obstructions.

- DO NOT use emergency release to pull the door open or closed.

In case of a power failure or door obstruction, PULL

EMERGENCY knob to release door from opener.

To Disconnect Trolley for Manual Operation

With the door closed, pull down the emergency release knob to

the DISCONNECT position. The door can be raised / lowered

manually.

To Re-connect Trolley

Pull the knob toward the opener so that the lever will flip up to

the CONNECT position. The trolley will reconnect itself when

the opener is activated or when the door is manually opened/

closed

Lever

CONNECT

DISCONNECT

Pull to Disconnect

Flip to reconnect

Operation / Condition Courtesy Light Response

Opener is initially plugged-in / Power restored Flashes five times

Upon opener activation Turns on for 4-1/2 minutes and turns off automatically

“LEARN” button is pressed Turns on for 30 seconds

Remote / Keyless entry PIN code accepted Flashes twice

The photo eye system is obstructed during door-closing or

door is obstructed during opening Flashes for 30 seconds (Re-align and clear obstruction)

Opener motor overheat (Thermal Protection) Flashes 5 times (Wait about 15 minutes to cool down)

Courtesy Light Responses

Manual Operation

Door status Activation using Push Button / Remote

Door at fully open / close position Door will move to fully close / open position

Door is closing Door will reverse

Door is opening Door will stop

Door is stopped as intended in partially open position Close

Door is obstructed while closing Door will reverse while flashing courtesy light

Door is obstructed while opening Door will stop

Door is fully opened and photo eye system is obstructed Door will not close

Door Status vs. Activation

Troubleshooting

Problem Possible Cause / Solution

Opener does not close and light flashes The photo eye safety system is misaligned or obstructed, refer to

pages 15 for proper alignment.

Opener does not respond to remote - Refer page 19 to reprogram remote.

- Check remote battery

Opener stops before reaching full open / close

position

Either the travel limit or force is not properly adjusted, check

adjustment referring to pages 16-17. Conduct safety reverse test after

ANY adjustment.

The door reverses unintentionally

- Make sure the photo eye safety system is aligned and clear of

obstructions.

- Refer to page 4 to check the door balance

- Refer to page 17 to re-adjust the force

The door reverses upon touching the floor and

the courtesy light flashes

Refer to page 16 to decrease close limit by 1/4 turn until door stops

as intended at the fully closed position. Conduct safety reverse test

after ANY adjustment.

The courtesy light flashes 5 times and the

Opener does not start Opener motor overheat, please wait about 15 minutes and retry.

The opener does not close the door and the

green LED on the photo eyes flashes

The photo eye safety system is misaligned or obstructed, refer to

page14 for proper alignment.

The opener is working properly but the courtesy

light does not turn on Replace light bulb (A19 incandescent Max.100W).

The courtesy light does not turn off Defective logic board.

The opener hums as the trolley hits the trolley

stop bolt in open travel

1. Make sure the trolley is towards the trolley stop bolt.

2. Disconnect the trolley by using the emergency release.

3. Close the door manually

4. Relieve the chain tension by loosening both the chain-to-cable

connector and the flange nut (see page 6)

5. Operate the opener so the trolley shaft travels towards the door

(Trolley should be kept disconnected)

6. Refer to page 16 to decrease open travel limit by 2 full turns

7. Refer to page 6 to re-tighten the chain until it is 1/4” (6mm) above

the base of rail (reference the figure shown on page 6).

8. Repeat the above steps if the trolley still hits the stop bolt.

Schedule Maintenance

Once a month Door balance test, refer to page 4.

Safety reverse test, refer to page 18.

Twice a year Check chain tension ( refer to page 6 for adjustment if necessary).

Once a year

- Limit and force adjustment may be necessary due to weather conditions.

Refer to pages 16-17 for adjustment. Conduct safety reverse test after ANY

adjustments.

- Lubricate door rollers, bearings and hinges. The opener is permanently

lubricated, DO NOT lubricate or grease the opener, rail or door tracks.

Maintenance

Repair Parts

Installation Parts

Rail Assembly Parts

Accessories

Part No. Name / Description

RP-001 Rail—Header Segment

RP-002 Rail—Middle Segments

RP-003 Rail—End Segment with Stop Bolt

GUT-840 Pulley

RP-004 Trolley

RP-005 Trolley Shaft and Cable

GUT-410 Master Link Set

Item

8 RP-006 Chain

Item Part No. Name / Description

1 RP-007 Header Bracket

2 GUAT-022 Door Bracket

3 RP-008

Hardware Bag with Emergency

Release Handle& Rope

(Installation hardware shown on P.3)

4 GUAT-024 Curved Door Arm

5 GUAT-025 Straight Door Arm

6 GUAT-026 Emergency Release Handle + Rope

7 RP-009 Hanging Bracket

4 5 6

7 8

1 2 3

4 5 6 7

Item Part No. Name / Description

1 GUAT-201 Photo Eye Safety System

(Emitter + Sensor with Brackets)

2 STDPX Push Button

3 58502 1-Button Remote

5 GUAT-203 23AE 12 Volt Alkaline Battery

6 57939 Keyless Entry Pad

7 CR-001 Owner’s Manual

4 57938 3-Button Mini Remote

*Optional

To purchase optional accessories, visit a Craftsman outlet, call 1-888-331-4569, or go online to www.craftsman. com

To purchase repair parts, call 1-888-331-4569.

Part No. Name / Description

GUAT-327 Sprocket Cover

GUAT-323 Sprocket and Gear Assembly

GUAT-341 Chassis

GUAT-303 Light Plate

CR-003 Light Lens Cover

GUAT-305 Capacitor

GUAT-306 Capacitor Holder

Item

8 CR-004 AC Service Motor & Bracket Assembly

9 GUAT-308 Garage Door Opener RPM Wheel

10 GUAT-309 Logic Board Holder

11 GUAT-310 Logic Board with Holder

13 GUAT-312 Limit System Assembly

14 CR-002 Opener Cover

12 GUAT-311 Limit System Driving Gear

Green

Screw

Gear

Close limit Contact

Open limit Contact

Center limit Contact Red

Screw

Orange

Blue

Green

Limit System Assembly

3 4

Opener Assembly Parts

* Should be replaced by qualified technician only

CRAFTSMAN WARRANTY

90-DAY IN-HOME LIMITED WARRANTY

FOR 90 DAYS from the date of sale this product is warranted against defects in material or

workmanship. With proof of purchase a defective product will be repaired free of charge.

LIMITED WARRANTY ON PARTS

FROM THE 91st DAY THROUGH 1 YEAR from the date of sale this product is warranted against

defective parts. With proof of purchase a new part will be furnished to replace a defective one free

of charge. Any costs for professional installation are not included.

LIMITED WARRANTY ON MOTOR

FROM THE 91st DAY THROUGH 4 YEARS from the date of sale the motor on this product is

warranted against defects in material or workmanship. With proof of purchase a new motor will be

furnished to replace a defective one free of charge. Any costs for professional installation are not

included.

WARRANTY SERVICE

For warranty coverage details to obtain product repair or replacement parts, visit the web page:

www.craftsman.com/warranty

WARRANT RESTRICTION

This warranty does not cover light bulbs, which are expendable parts, or repair parts necessary

because of operator abuse or negligence, including the failure to install, adjust and operate this

garage door opener according to instructions contained in the owner’s manual. This warranty also

does not cover any problems caused by interference.

LIMITATION ON LIABILITY

Seller will not be liable for loss or damage to property or any incidental or consequential loss or

expense from property damage due directly or indirectly to the use of this product. Some states do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

DISCLAIMER OF IMPLIED WARRANTIES

Except for the motor, all implied warranties for this product, including but not limited to any implied

warranties of merchantability and fitness for a particular purpose, are limited in duration to the 90

day and 91st day through 1-year limited warranty period set forth above. All implied warranties with

respect to the motor are limited in duration to the 91st day through 4-year limited warranty period set

forth above. No implied warranties will exist or apply after such periods. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

This warranty applies only while this product is in use in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

Craftsman 20057933 Sears20170406 User Manual GARAGE DOOR OPENER Manuals And Guides 1705089L

Navigation menu

Versions of this User Manual:

Views

Navigation