Craftsman 31511782 User Manual 4 INCH BELT SANDER Manuals And Guides L0805053
CRAFTSMAN Sander Manual L0805053 CRAFTSMAN Sander Owner's Manual, CRAFTSMAN Sander installation guides
User Manual: Craftsman 31511782 31511782 CRAFTSMAN CRAFTSMAN 4 INCH BELT SANDER - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 4 INCH BELT SANDER #31511782. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 4 INCH BELT SANDER Manual
Open the PDF directly: View PDF 
.
Page Count: 8
OWNERS
MANUAL
MODEL NO.
315.11782
CAUTION:
Read Rules for
Safe Operation
and instructions
Carefully
,@
4 INCH ELT SANDER
WRTH DUST PICK-UP
DOUBLE INSULATED
Introduction
Operation
Maintenance
Repair Parts
Designed exclusively for and sold onfy by
SEARS, ROEBUCK AND CO_, Chica.qo, IL 60684 U .S.A. and SIMPSONS-SEARS LIMITED, Toronto, Canada
2-620263-965
7-78 PRIt.IT[,D IN L__,_,
FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT SANDER
If this Craftsman Belt Sander fails to give complete satisfaction within one year from the date of
purchase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and
Sears will replace it, free of charge.
If this belt sander is used for commercial or rental purposes this warranty applies for only 90 days
from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. SEARS, ROEBUCK AND CO.
BSC 41 _ 3
SEARS TOWER
CHICAGO, 1L 60684
gNTRODUCTION
DOUBLE INSULATION is a concept in safety, in
etectric power tools, which eliminates the need for
the usual three wire grounded power cord and
grounded supply system. Wherever there is electric
current in the tool there are two complete sets of
insulation to protect the user_ All exposed metal
parts are isolated from the internal metal motor
components with protecting insulation..
IMPORl'ANT_Servicing of atool with double in-
sulation requires extreme care and knowledge of the
system and should be performed only by a qualified
service technician.. For service we suggest you
return the tool to your nearest Sears Store for repair.
Always use original factory replacement parts when
servicing.
RULES FOR SAFE OPERATION
Your Craftsman 4-inch Dustless Belt Sander is suitable
for coarse, medium and fine sanding of wood, metals,
plastics and other materials. It is ideal when used for
smoothing rough boards, chamfering, rounding edges
and many other general sanding applications. It is ideal
for refinishing large pieces of furniture, stairs and
other large surfaces. Its balanced design makes it easy
to use.
The built-in dust collection system will remove most of
the sanding dust from the work and eliminate the dust
in the air -- usually associated with power sanding°
SWITCH
A trigger switch controls operation of the Sander',
The trigger switch can be locked on for continuous
operatiom To lock, pull trigger, press lock button
inward, and release trigger, Pull trigger and release
to stop°
1. KNOW YOUR POWER TOOL _ Read owner's manual carefulty,_ Learn its applications and limitations
as well as the specific potential hazards peculiar to this tool.
2, GROUND ALL TOOLS -- UNLESS DOUBLE-INSULATED. If tool is equipped with three-prong
plug, it should be plugged into a three-hole electrical receptacle, tf adapter is used to accommodate
two-prong receptacle, the adapter wire must be attached to a known ground. (Usually the screw
securing receptacle cover plate)_ Never remove third prong.
3. KEEP GUARDS IN PLACE and in working order.
4 KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
5. AVOID DANGEROUS ENVIRONMENT° Don't use power toot in damp or wet locations or expose to
r&in. Keep work area well tit.
6 KEEP CHILDREN AWAY. Al! visitors should be kept safe distance from work area.
7. STORE IDLE TOOLS. When not in use, tools should be stored ;n dry, high or-locked-up place_out of
reach of children_
8_ DON'T FORCE TOOL. it will do the job better and safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty toot..
10 WEAR PROPER APPAREL. No loose clothing or jewetry to get caught in moving parts_ Rubber gloves
and footwear are recommended when working outdoors,
11 USE SAFETY GLASSES with most tools. Also face or dust mask if cutting operation is dusty_
12 DON'T ABUSE CORD. Never carry toot by cord or yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges°
!3. SECURE WORK. Use clamps or a vise to hold work it's safer than using your hand and it frees both
hands to operate tool
14 DON'T OVERREACH. 'Keep proper footing and balance at all times..
15 MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times, and clean for best and safest per-
formance. Follow instructions for lubricating and changing accessories.
16 DISCONNECT TOOLS. When not in use, before servicing; when changing attachments, blades, bits,
cutters, etc.
17 REMOVE ADJUSTING KEYS AND WRENCHES, Form habit of checking to see that keys and ad-
justing wrenches are removecf from tool before turning it on
!8 AVOID ACCIDENTAL STARTING. Don't carry plugged-in tools with finger on switch Be sure switch
is off when plugging in.
19 OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords suitable
for use outdoors and so marked
Page 2
,\
Fig, I
Fig, 2
OPERATION
PREPARING FOR OPERATION
Your Sander is equipped with its own built-in auxiliary handle
located at the front of the unit, This handle allows for two-
hand use which wilt aid in maintaining complete control and
keeping sanding area level with work piece (See Fig, 1),
Selecting the correct size and type sanding belt is an extremely
important step in achieving ahigh quality sanded finish,.
Aluminum oxide silicone carbide and other synthetic abrasives
are best for power sanding.
In general, coarse grit will remove the most material and finer
grit will produce best finish in all sanding operations, The
condition of the surface to be sanded will determine which grit
belt will do the job, If the surface is rough, start with a coarse
grit belt sanding until surface is uniform., Medium grit belt may
then be used to remove scratches left by the coarser belt and
finer grit belt used for finishing of the surface. Always con-
tinue sanding with each grit belt until surface is uniform°
INSTALLING AND ADJUSTING SANDING BELT
Be sure power cord is disconnected from power supply.
1. Release tension on belt by pushing the front pulley
squarely against the top or edge of workbench (See Fig. 2).
When the pulley is pushed back it will lock in that position,
allowing slack in the belt so it can be removed. NOTE: Idler
pulley rubbing housing when in the released position,
without sandpaper, does not damage toot operation. The
sanding belt, when assembled, will not allow pulley to
project as far.
2, To install new belt, place belt over both pulleys, making
sure that arrow on inside of belt is pointing in the direction
of rotation which is clockwise when looking into open side
of sander.
3,. Make sure fingers are not in a position to get mashed. Pull
hard on lever (A) until pulley is released and tension is
applied to bett. The lever will move freely at first and then
become harder to pull
4,, To adjust belt, connect sander to power supply,, Stand
sander on end as illustrated (See Fig,, 3), Pull switch trigger
and release immediately while observing tracking of belt.
5o tf belt runs outward, turn tracking screw (B) clockwise and
counterclockwise if belt runs inward. This should be done
until you are sure belt will not come in contact with rub
strip,
6 Start sander and fine adjust the tracking screw (B) until belt
stabilizes. When correctly adjusted, the outer edge of the
belt will be even with outer edge of wear plate,
Note: Belt life will be increased if a few seconds are spent
adjusting the belt tracking properly°
TO OPERATE
Clamp or otherwise secure the work to prevent it moving under
the Sander., With Sander off work, press the trigger switch and
when the motor reaches its maximum speed, lower the Sander
on the work with a slight forward motion Using the main
handle to control the Sander and the front handle only to guide
it, move it slowly over the work, Allowing the Sander to remain
in one place will result in an uneven surface, The Sander was
designed to provide the proper weight on the sand belt and
extra pressure wil! only result in uneven work, stow cutting
from slow belt speed, clogged belts and possible motor burn-
ouL
Use the proper belt when heavy cutting is desired, not heavy
pressure. The importance of this cannot be over-emphasized,
the weight has been built into the tool to give the most ef-
ficient pressure at the proper location.
Poge 3
MAgNTENANCE
WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
BRUSH REPLACEMENT
ISH
Fig 4
Disconnect sander trom power supply.
1Remove brush caps (A) with screwdriver. See Fig 4
2. Remove brushes (B).
3,_ Reassemble new brushes into sander, making sure tab on
brush is inserted in opening between brush tube and brush
holder and that the brush moves freely in the brush tube_
4, Replace brush caps.
TIMING BELT REPLACEMENT (SEE FIG. 5).
DISCONNECT SANDER FROM POWER SUPPLY.
H
/GiE
Fig 5
CAUTION -- TO RETAIN ELECTRICAL INSULATION AND
PROVIDE USER PROTECTION AS PROVIDED IN ORIGINAL
DESIGN, ALL PARTS REMOVED MUST BE REASSEMBLED
AND THE REPLACEMENT BELT MUST BE AN IDENTICAL
REPLACEMENT PART.
1, Remove dust bag and two screws (A).
2. Remove blower coupling (B) by inserting a screwdriver
between the blower housing (C) and blower coupling, this
will expose the blower (D) within the blower housing.
3_
4,_
Remove cap screw (E) by turning it clockwise with a 3/16"
hexagonal key, this will permit washers (F) and (G) and the
blower-to be removed,,
Remove four screws holding the cover and blower housing
assembly to the belt housing and take it off the sander°
5;
6_
Note the position of spacer (H)o This spacer may be
removed or left on the shaft,.
Force old belt off small pulley with a screwdriver and
remove it from large pulley,
Install new belt over large pulley making sure teeth on belt
mesh with teeth on pulley.
8, Press the belt onto the small pulley,,
9,. Clean the blower and dust passages before reassembling.
10, Reassemble all parts, Turn cap screw (E) counterclockwise
to tighten, When reassembling blower coupling use
caution not to over' tighten screws.
The operation of any Power Tool can result in foreign objects being
thrown into the eyes, which can result in severe eye damage. Always
wear safety glasses or eye shields before commencing power tool
operation° We recommend Wide Vision Safety Mask for use over
spectacles or standard safety glasses, available at Sears Retail or
Catalog Stores,
Page 4
GENERAL
DUST PICK-UP The dust bag assembly is slipped
with a twisting motion over the blower exhaust.. The
bag may be turned toward the side as required for
the operator's convenience Although the bag is of
ample size it should be emptied frequently to
maintain the pick-up efficiency. The bag is emptied
by grasping the fitting and twisting it off the blower
exhaust. Opening the zipper at the bottom of the bag
will allow complete cleaning.. When sanding, some
dust, paper, belt threads and etc. may collect on the
blower and reduce the efficiency of the blower.. To
clean blower (See Fig. 5) remove screws (A) and
blower housing coupling (B)_. Replace blower
housing coupling (B) and screws (A).. Do not over
tighten screws (A)o
All the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life
of the unit under normal operating conditions,
therefore, no further lubrication is required.
Only the parts shown outside Section A on page six
are intended to be replaced by the customer,. Parts
listed in Section A represent an important part of the
double insulation system and should be serviced
only by a qualified service technician°
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to various types of
commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, carbon dust,
etc.
When electric tools are used on fiberglass boats,
sports cars, etc., it has been found that they are
subject to accelerated wear and possible premature
failure, as the fiberglass chips and grindings are
highly abrasive to bearings, brushes, com-
mutator,etc. Consequently it is not recommended
that this tool be used for continuous production
work on any fiberglass material. During any use on
fiberglass it is extremely important that the tool is
cleaned frequently by blowing with an air jet°
EXTENSION CORDS
The use of any extension cord wil! cause some loss
of power° To keep the toss to a minimum and to
prevent tool overheating, follow the recommended
cord sizes on the chart at right. Extension cords are
available at Sears Catalog Order or Retail Stores.,
Extension Cord Length Wire Size Ao W. G.
25-50 Feet 14
50-75 Feet 12
75-100 Feet 10
THE FOLLOWING RECOMMENDED ACCESSORIES WERE AVAILABLE
AT THE TIME THIS MANUAL WAS PRINTED.
CARRYING CASE
Cat No 91457C
ASSORTED SANDING BELTS
Cat No 9 22332--X-Fine
Cat No 9 22333_Fine
Cat No 9 22334_Medium
Cat No 9 22335_Coarse
Cat No 9 22336_X-Coarse
li[ :. _,: i m ...... !_
CORD LOCK
Cat No 2 2595
Belts best for metal
Cat No 9 22337_Fine
Cat No 922338_-Medium
Cat No 9 22339_Coarse
CAUTION : The use of attachments or accessories not listed above might be hazardous.
Page 5
CRAFTSMAN 4 INCH BELT SANDER WITH DUST PICK-UP -- MODEL NUMBER 315.11782
16 15
t9
\
91
f
59
6?
50
57 _/; 56
FOR, PARTS LIST -- SEE PAGE 7
Page 6
Ne+
I
2
3
PaN
Number
1-607461-01
2-616452-03
4 2-606712-02
5 1-622167-28
6 1-703493-803
7 !-622205-04
8 1-622172-04
9 1-622149-92
10 1-611037-01
11 4-611041-03
12 2-611038-03
13 1-941401-36
14 1-703473-21
15 1-614658-04
16 1-614658-34
17 1-622204-15
18 1-622199-03
19 3-611050-02
20 3-606723-04
21 2-621766-00
22 1-622922-00
23 2-623245-00
24 2-612070-01
25 1-795247-06
26 1-606124-01
27 1-622183-06
28 1-622183-02
CRAFTSMAN 4 INCH BELT SANDER WITH DUST PICK-UP -- MODEL NUMBER 315.11782
I The Model Number will be found on o plate attached to the Base, Always
mention the Model Number in all correspondence regarding your SANDER
or when ordering repair parts.
I
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
PARTS LIST
_rtption _uan.
Sanding Belts (4" x 24'9
Retaining Ring t
Hi-Pro Key
**STD580014 l
Drive Pulley 1
Retaining Ring
Washer 3
Thrust Bearing 4
Shaft Seat !
Needle Beanng
(Tarnngtan B-87)
* *STD310807 4
Spacer 1
Yoke Support Bracket
Yoke Release Lever i
Rail Pin **STD571812 t
Lock Washer
**STD551 t08 3
*Screw (#8-32 x 72 Pan
Hd.) **STDS10805 2
*Screw (#8-32 x 31,_
Pan Hd.) !
Spacer 2
O-Ring 2
Yoke and Slide Assembly l
Idler Pulley (includes
Two Key No. 9) l
Idler Puiley Shaft i
Spring 1
Belt Rub Str_p !
Data Plate l
Drwe Screw 6
*Screw (#6-20 x Y2
Pan Hd. T.F.)
* * STD610605 6
*Screw (IA-20 x 3/_
Flat Hd.) 2
*Screw "(#! 0-24 x 3/_
Flat Hd.) t
Kay PaN
No. Number
29 1-611036-01
30 1-607453-02
31 2-606995-01
32 2-606970-01
33 2-621764-00
34 1-616081-I2
35 1-614658-10
36 1-606997-01
37 2-621757-02
38 4-606859-01
39 2-607001-01
40 2-606785-01
41 2-621824-00
42 1-621585-01
43 3-606759-03
44 1-622149-106
45 4-611061-07
46 2-607743-01
47 2-607751-02
48 1-616081-01
49 1-607407-01
50 1-607033-01
51 1-615095-01
52 1-616081-13
53 2-622848-01
54 1-621646-02
55 1-931744-818
Doscript|on
Spring
Tracking Screw
Pad Backing
Wear Plate
Sander Pad Retainer
*Screw (#8-T8 x 3/_
Pan Hd. T.C,) 2
*Screw (#8-18 x 3/_ Pan
Hd.) **STD510803 3
Spacer ,. 1
Driven Sprocket I
Belt Housing ]
Gear with Shaft 1
Gasket 1
Grease Seal 1
Ball Bearing (N.D.
#Z99500
* *STD3 ! 5205 2
Pimon Shaft 1
Needle Bearing
(Tornngtan M-471 ) l
Base (Includes Key
Nos. 8, 44, and Two
Key No. 9) !
Dust Skirt 1
Dust Skirt Retainer [
*Screw (#8-18 X 5_
Pan Hd. T.C.) 1
Screw (#18 x 1 Pan
Hd. T.F.) . . 3
Spacer . 1
Lock Washer 1
*Screw (#8-18 x Y2 Pan
Hd.} **STD6_0805 2
Blower Coupling 1
Cap Screw (]/_-20 x 3/_
Left Hand Thread,
Hex Socket] 1
Washer ]
Quoin,
I
|
f
1
K_ PaN
Ne. Number
56 2.611014-01
57 1-607407-03
58 2-611389-01
59 3-607034-01
60 2-621826-00
61 2-606727-01
62 1-616081-03
63 4-607012-01
64 1-616081-04
65 1-931055-05
66 1-624198-01
67 2-612217-01
68 2-612102-01
69 2-612089-01
70 2-612112-01
71 1-607400-01
72 t-706404-07
73 1-614658-12
87 4-621930-00
88 2-621893-00
89 1-701511-804
90 2-621931-01
91 3-622084-01
92 1-611764-01
2-620263-965
Description
Blower
Screw (#8-| 8 X I 7/8
Pan Hd. T.F.)
Logo Plate .
Cover and Blower
Housing Assembly
Timing Belt
Drive Sprocket
*Screw (#8-t8 x 1
Pan Hd. T.C.)
End Cap .
*Screw (#8-|8 x 3z_
Pan Hd. T.C3
* *STD6 | 0807
Washer
Brush Cap
Logo Plate ....
Brush Assembly
Brush Tube
Brush Holder
Spacer
Hex Nut (#8-32)
** STD54 _008
*Screw (#8-32 x 15/| 6
Pan Hd.)
**STD510810
Dust Bag
Bag Fitting
Washer
Support
Dust Bag Assembly
(includes Key Nos.
87, 88, 89 and 90)
Washer
Owners Manual
(Not illustrated)
NOTE: "A"--The assembly shown represents an important part cf the Double Insulated System. To avoid the possibility of alteration or
damage to the System, service should be performed bv your nearest Sears Electric Motor Shop/Specialty Repair Center. Contact
your nearest Cata|og Order or Retail Store.
"Standard Hardware Item_May Be Purchased Locally *"Sanding Belts in Assorted Gr=ts for Sanding Both Wood and Metal May Be Obtained
**Available From Div. 98--Source 980.00 from Your Nearest Sears Catalog Order or Retail Store.
FOR ILLUSTRAT|ON _SEE PAGE 6
Page 7
Quatl,
2
1
i
!t
2
1
2
2
4
1
2
2
2
I
I0
5
1
1
l
l
I
i
Sears
OWNERS
MANUAL
SERVICE
MODEL NO.
315.11782
HOW TO ORDER
REPAIR PARTS
®
4 NCH ELT SANDE
WroTHDUST PICKoUP
DOUBLE BNSULATED
Now that you have purchased your Sander, should a
need ever exist for repair parts or service, simply con-
tact any Sears Service Center- and most Sears, Roebuck
and Co or Simpsons-Sears Limited stores, Be sure to
provide all pertinent facts when you call or visit,
The model number of your Sander will be found on the
plate attached to the base,
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION '
o PART NUMBER o PART DESCRIPTION
o MODEL NUMBER o NAME OF lTEM
315.11782 Belt Sander
AIJ parts listed may be ordered from any Sears Service
Center and most Sears stores,
If the parts you need are not stocked locally, your order
will be electronically transmitted to a Sears Repair
Parts Distribution Center for handling,
SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A. and SIMPSONS-SEARS LIMITED, Toronto, Canada
]
