Craftsman 315175050 User Manual DOUBLE INSULATED ROUTER Manuals And Guides 98080200

CRAFTSMAN Router Manual 98080200 CRAFTSMAN Router Owner's Manual, CRAFTSMAN Router installation guides

User Manual: Craftsman 315175050 315175050 CRAFTSMAN DOUBLE INSULATED ROUTER - Manuals and Guides View the owners manual for your CRAFTSMAN DOUBLE INSULATED ROUTER #315175050. Home:Tool Parts:Craftsman Parts:Craftsman DOUBLE INSULATED ROUTER Manual

Open the PDF directly: View PDF PDF.
Page Count: 28

MODEL NO. 315.175040 •
, EAR
OWNER'S
MANUAL
MODEL NOS.
315.175040
315.175050
315.175060
CAUTION:
Read and follow
ALL safety rules
and instructions
. before operating
th_ °equipment.
MODELNO.315.175060
MODELNO.315.175050
CRAFTSMI:iN"
Router
Thank You for Buying A
Craftsman Router
DoUble Insulated
Warranty
Rules For Safe Operation
Table Of Contents
Introduction
Unpacking
Features
Operation
Maintenance (_
Acce.ssories
Repair Parts
972000-248
5-98
SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A.
Printed in U.S.A.
i i i ii
FULL ONE YEAR WARRANTY ON CRAFTSMAN ROUTER
If this Craftsman Router fails to give complete satisfaction within one year from the date of purchase, RETURN IT
TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair it, free of charge.
If this Craftsman Router is used for commercial or rental purposes, this warranty applies for only 90 days from the
date of purchase.
This warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.
Sears, Roebuck and Co., DEPT. 817 WA, Hoffman Estates, IL 60179
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL
NOTE:
MEANING
ii
SAFETY ALERT SYMBOL:
Indicates caution Or warning. May be used in conjunction with other symbols or pictogrephs.
ii i
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
i ii
CAUTION: Failure to obey a safety waming may result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal
injury.
i
Advises you of information or instructions vital to the operation or maintenance of the equipment.
DOUBLE INSULATION is a safety concept inelectric power
tools which eliminates the need for the usual three wire
grounded power cord and grounded supplysystem.Wherever
there iselectric current inthe toolthere are two complete sets
of insulation to protect the user. All exposed metal parts are
isolatedfromintemal metal motorcomponentswith protecting
insulation.
IMPORTANT -Servicing of a tool with double insulation
requires extreme care and knowledge of the system and
should be performed only by a qualified service technician.
For service we suggest you return the tool to your nearest
Sears Store for repair.Always use originalfactory replacement
parts when servicing.
ELECTRICAl:.' CONNECTION
Your router has a prec,_ion built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only
(normal household current). Do not operate this tool on direct current (DC). Avoltage drop of more'than 10 percent will
cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check
the power supply.
ii i
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Paoe 2
WARNING:
Do not attempt to operate this tool until you have
read thoroughly and understand completely all
instructions, safety rules, etc. contained in this
manual. Failure to comply can result in accidents
involving fire, electric shock, or serious personal
injury. Save owner's manual and review frequently
for continuing safe operation, and instructing others
who may use this tool.
WARNING:
The doubleinsulatedsystemis intendedto protectthe
user from shock resultingfrom a break in the tool's
internalwiring. Observeall normal safety precautions
relatedto avoidingelectricalshock.
i
READ ALL INSTRUCTIONS
1. KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitationsas well as the specificpotentialhazards
related to this tool.
o
.
4.
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges, refrigerator
enclosures.
KEEP GUARDS IN PLACE and in working order.
KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
5. AVOID DANGEROUS ENVIRONMENT. Don't
use power tool in damp or wet locations or expose
to rain. Keep work area well lit,
6. KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept
a safe distance from work area. Do not let
visitors contact tool or extension cord.
7. STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place-, out of the reach of children.
8. DON'T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy du_ tool.
Don't use =tool for purpose not intended - for
example - A cir.eularsaw should never be used
for cutting tree limbs or 10gs.
10. WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair
covering to contain long hair and keep it from
being drawn into nearby air vents.
11. ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses;
they are NOT safety glasses.
12. PROTECT YOUR LUNGS. Wear a face or dust
mask if operation is dusty.
13. PROTECT YOUR HEARING. Wear hearing
protection duringextended periods of operation.
14. DON'T ABUSE CORD. Never carry tool by cord
or yank it to disconnect from receptacle. Keep
cord from heat, oil and sharp edges.
15. SECURE WORK. Use clamps or a vise to hold
work. Both handsare needed to operate the tool.
16. DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17. MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
18. DISCONNECT TOOLS. When not in use, before
servicing,orwhen changing attachments, blades,
bits,cutters,etc., all tools shouldbe disconnected
from power supply.
19. REMOVE ADJUSTING KEYs AND WRENCHES.
Form habit of checking to see th8t keys and
adjusting wrenches are removed from tool be-
fore tuming it on.
20. AVOID ACCIDENTAL STARTING. Don't carry
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
Page 3
............_-_..........._............" AFERULES_ FOR,!S OP ERATIOK(Cd_ntinu_)_
21.
22.
23.
MAKE SURE YOUR EXTENSION CORD IS IN
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord
will cause a drop in line Voltage resulting in loss of
power and overheating. A wire gage size (A.W.G.)
of at least 14 is recommended for an extension
cord I00 feet or less in length. A cord exceeding
I00 feet is not recommended. If in doubt, use the
next heavier gage. The smaller the gage number,
the heavier the cord.
OUTDOOR USE EXTENSION CORDS. When tool
is used outdoors, use only extension cords suitable
for use outdoors. Outdoor approved cords are
marked with the suffLxW-A, for example - SJTW-A
or SJOW-A.
KEEP CUTTERS CLEAN AND SHARP. Sharp
cutters minimize stalling and kickback.
24. KEEP HANDS AWAY FROM cu'n'ING AREA.
Keep hands away from cutters. Do not reach
undemeath work while cutter is rotating. Do not
attempt to remove material while cutteris rotating.
25. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
26. INSPECT TOOL CORDS PERIODICALLY and
if damaged, have repaired at your nearest Sears
Repair Center. Stay constantly aware of cord
location.
27. INSPECT EXTENSION CORDS PERIODI-
CALLY and replace if damaged.
28. KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any strong
solvents to clean your tool.
29. STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
30. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. Aguard or other part that is
damaged should be properly repaired or replaced
by an authorized service center unless indicated
elsewhere in this instructionmanual.
31. DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
32. INSPECT FOR and remove all nails from lumber
before routing.
33. DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
34. WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
35. POLARIZED PLUGS. To reduce the risk of
•electric shock, this tool has a polarized plug (one
blade is wider than the other). This plug will fit in
apolarized outlet only one way. If the plug does
notfit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
install the proper outlet. D<_not change the plug
in any way.
36. DO NOT USE TOOL UNDER "BROWN-OUT"
OR OTHER LOW VOLTAGE CONDITIONS.
Also, do not use with any device that could cause
the power supply voltage to change.
37. WHEN USING THIS ROUTER WITH A
ROUTER TABLE, HELP PREVENT POS-
SIBLE SERIOUS INJURY BY KEEPING THE
CUTTER GUARDED AT ALL TIMES. Use only
router tables, with guards, that have been de-
signed for use on routers that are of this type,
size, and weight.
38. SAVE THESE INSTRUCTIONS. Review them
frequently and use them tO instruct others who
may use this tool. If you loan s_meone this tool,
loan them these instructions also.
[AwA..l.G:]
_The operation 0; any router can result in foreign objects being thrown into your eyes, which ]
E(_M-_=_)_ can result in severe eye damage. Before beginning power tool operation, always wear
p_ safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
,_ with side shields, available at Sears Retail Stores.
Page 4
[] Warranty ........................ ,...., .................. 2
[] Rules For Safe Operation ........... ,.,.,.2-4
[] Table •Of Contents ................................. 5
[] Introduction and Product
Specifications ....................................... 6
[] Unpacking ............................................. 7
[] Features .............................................. 7-9
Switch .................................................. 7
Lock-On Button ....................................... 7
Chip Shield ............................................. 7
Wrench Storage Area ............................. 7
Variable Speed (Model Nos,
315.175050 and 315.175060 Only) ........ 7
Dust Bag Assembly
(Model No. 315.175060 Only) ................ 7
To Install Dust Bag ............................ 7
To Empty Dust Bag ........................... 7
Know Your Router .................................. 8
Model No. 315.175040 ...................... 8
Model No. 315.175050 ...................... 9
Model No. 315.175060 ...................... 9
[] Operation ........................................ 10-17
Installing/Removing Cutters .................. 10
Depth Of Cut Adjustments .................... 11
Depth Of Cut Adjustments When
Mounted To ARouter Table ................. 12
Variable Speed (Model Nos.
315. 175050 and 315.175060) ............. 12
Practice Before Actual Use ................... 12
Routing ................................................ 13
Freehand Routing ................................. 13
[]
[]
[]
Proper Feeding ..................................... 14
Speed Selections (Model Nos.
315.175050 and 315.175060 Only) ...... 14
Rate Of Feed ........................................ 14
Force Feeding ...................................... 14
Too Slow Feeding ............ _.................... 14
Depth Of Cut ......................................... 15
Direction Of Feed and Thrust ............... 15
Routing ................................................ 15
Starting and Ending ACut
Internal Routing ............................... 16
Edging With Pilot Bits ........................... 16
Edge Routing ........................................ 16
Routing With Guide Bushings ............... 17
Router Tables ....................................... 17
Maintenance ................................... 17-22
Switch Replacement
(Model No. 315.175040) ....................... 17
Switch Replacement (Model Nos.
315.175050 and 315.175060) .............. 18
Light Bulb Replacement ....................... 19
Proper Care Of Cutters ......................... 19
Proper Care Of Collet ........................... 19
Lubrication ............................................ 19
Helpful Hints ......................................... 19
General ................................................ 20
Extension Cords ................................... 20
Accessories ........................................ 21
Exploded View and Parts List ...... 22-27
Parts Ordering IService ..................... 28
Page 5
Congratulations and thank you for buying this
Craft=man router. It has been designed, engineered and
manufactured to provide you with Sears high standard of
dependability, ease of operation, and operator safety.
Properly cared for, it will give you years of rugged, trouble-
free performance.
Your router has many features for making routing operations
more pleasant and enjoyable. Safety, performance and
dependability have been given top pdority in the design of
this router making it easy to maintain and operate.
CAUTION:
Carefully read through this entire owner's manual before
using your new router. Pay close attention to the Rules
For Safe Operation, Warnings and Cautions. If you use
your router propedy and only for what it is intended, you
will enjoy years of safe, reliable service.
SPECIFICATIONS:
DEPTH OF CUT
COLLET
HORSEPOWER
Model No. 315.175040
Model No. 315.175050
Model No. 315.175060
AMPS
Model No. 315.175040
Model No. 315.175050
Model No. 315.175060
RATING
NO LOAD SPEED
Model No. 315.175040
Model Nos. 315.175050 and 315.175060
POWER CORD
Model Nos. 315.175040 and 315.175050
Model No. 315.175060
DUSTLESS
Model No. 315.175060
NET WEIGHT
Model No. 315.175040
Model No. 315.175050
Model No. 315.175060
0-1-1/2 in.
1/4 in.
1-1/2
1-3/4
2
8.0
8.5
9.0
120 volts, 60 Hz, AC only
25,000 RPM
15,000 -25,000 RPM
6ft.
10ft.
8.13 Ibs.
8.14 Ibs.
9 Ibs.
Paae 6
Your muter has been shipped completely assembled and
ready for use. Inspect it car fully to make sure no breakage
or damage has occurred during shipping. If any parts are
damaged or missing, contact your nearest Sears Retail
Store to obtain replacement parts before attempting to
operate router. A wrench and this owner's manual are also
included.
i
WARNING:
If any parts are missing, do not operate your router until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
SWITCH
T_otum your router ON, depress the switch trigger. Release
switch trigger to turn your router OFF.
LOCK-ON BUTTON
The switch of your router is equipped with a lock-on feature
which is convenient when operating for extended periods of
• time. To lock on, depress the trigger, push inthe lock button
located on the side of the handle, then while holdingthe lock
button pushed in, release the trigger. To release the lock,
depress the trigger and release it.
WARNING:
Before connecting your router to power supply sour e,
always check to be sure it is not in lock-on position
(depress and release switch trigger). Failure to do so
could result in accidental starting of your muter resulting
in possible serious injury. Also, do not lock the trigger on
jobs where your muter may need to be stopped suddenly.
i
CHIP SHIELD
A clear plastic chip shield is installed on the front of your
router for protectionagainst flying dust and chips. The shield
isdesigned to fit the opening of the muter base. If necessary
to remove chip shield, squeeze the tabs on each end and pull
outward. To replace, squeeze the tabs at each end, fit into
-opening, thenrelease. NOTE: Model No. 315.175060 has a
chip shield on the front and rear opening of the router base.
For your protection, do not use router without chip
sh!eld(s) properly in place. Ifdesired, the horsepower label
can be removed from chip shield by simply peeling off.
WRENCH STORAGE AREA
Your router hasa wrench storage area located onthe topend
cap portionof the motor IlOusing.When installing orremoving
cutters, remove the wrench from its storage area. Proper
storage of wrench when not in use will help reduce the
possibility of losing wrench.
VARIABLE SPEED SWITCH WITH ELECTRONIC
SPEED CONTROL
(MODEL NOS. 315.175050 AND 315.175060 ONLY)
See Figures lb and lc.
Yol_q_outel_as advanced electronic features, designed to
assist you in getting the maximum use from your router. By
making pr perspeed selections, your muter can be adjusted
to specific routing needs. This eliminates much of the guess
work previously needed to perform a given job. Both the
experienced and inexperienced router users benefit,
obtaining pr fessional like results with fewer job err rs.
The variable speed control allows the router speed to be
adjusted from 15,000 to 25,000 rpm. The variable speed
control selector is conveniently located outside the right
handle near the operator's thumb or hand.
Speed can be set according to the approximate cutter
diameter you will be using and to the hardness of the
material being cut. The best cuts are made when the cutter
is fed thr ugh material at the proper rate of feed.
DUST BAG ASSEMBLY
(MODEL NO. 315.175060 ONLY)
See Figure lc.
The dust bag located on the side of your muter provides a
dust collection system for your router. For more efficient
operation, empty dust bag when half full.
Do not connect r uterto power supply before installing dust
bag or connecting it to a dust collection system.
WARNING:
To prevent the possibility of sawdust or foreign objects
being thrwn into your face and eyes, never attempt to
use your router without dust bag propedy installed.
Sawdust or foreign objects being thrwn intoyour face or
eyes could result in possible serious injury.
i
TO INSTALL DUST BAG:
The dust bag should be installed by slippi_j it v_th a twisting
motion over the blower exhaust. The bag should be installed
with the zipper down when router is in upright positiori.
TO EMPTY DUST BAG:
Remove dust bag from router, open zipper and shake out
dust. Occasionally turn the dust bag inside outand brash the
accumulation of dust from the inside of the bag. This will
allow the air to flow thr ugh the bag better.
Page 7
KNowYouR RoU_FER
Before attempting to use your router, familiarize yourself with
all operating features and safety requirements. See Figure 1.
i
WARNING:
Do not allow familiarity with your router to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict severe injury.
WARNING:
Always wear safety goggles or safety glasses with side
shieldswhen operating your router. Failure to doso could
result indust, shavings, loose particles or foreign objects
being thrown into your eyes, causing possible serious
injury.
WRENCH,
SPINDLE
DEPTH-
ADJUS_NG
RING
CHIPSHIELD
..:,.
MODEL NO. 315.175040
UPSIDE DOWN VIEW OF ROUTER
DEPTH INDICATOR
INDICATOR POINT
RING
POWER
HANDLE
SWITCH
LOCK-ON
BURTON
LOCKING
KNOB
DEPTH
INDICATORRING
INDICATOR
POINT ....
SUBBASE
WRENCH
STORAGE
AREA
HANDLE
Fig. la
Pnn_ R
• UPSIDE DOWNVIEW OF ROUTER 7
WRENCH DEPTH
RING
INDICATOR
POINT WRENCH
STORAGE
AREA
SPINDLE
DEPTH
ADJUSTING.
RING
CHIPSHIELD
WRENCH
SPINDLE STORAGEAREA
HANDLE
CHll
SHIELD
POWER
HANDLE
SWITCH
LOCK_N
BUTTON
LOCKING
KNOB
VARIABLESPEED
CONTROLSELECTOR
DEPTH
INDICATORRING
INDICATOR SUBBASE
POINTMODEL NO. 315.175050
UPSIDE DOWN VIEW OF ROUTER
DEPTH
INDICATOR
RING
POWER
COLLETNUT'_'
DEPTH SWITCH,
ADJUSTING TRIGGER
RING
DEPTH
INDICATOR
RING
BUTTON
LOCKING
KNOB
VARIABLESPEED
CONTROLSELECTOR
INDICATOR
POINT
MODEL NO. 315.175060
Page 9
INDICATOR
POINT
WRENCH
SUBBASE
DUSTBAG
HANDLE
Fig. lb
BLOWER
EXHAUST
Fig. lc
L
i
WARNING:• SPINDLE A_' _ _ )i
Your router should never be connected to power supply LOCK _/7 _ I _ [J[
when you are assembling XI _ _ _ _,___L__ 1
install ng or removing cul
°.oncn0,ourou.r
that o ,uld cause serious in]
:ee Fi_ Jres 2 and 3.
TO LOCK P H INTO TO UNLOCK
SPINDLE LOCKANDUNLOCK SPINDLE Fig. 2
when you are assembling parts, making adjustments,
installing or removing cutters, or when not in use.
Disconnecting your routerwill prevent accidental starting
that could cause serious injury.
INSTALLING/REMOVING CUTTERS
See Figures 2 and 3.
II UNPLUG YOUR ROUTER.
Failure to unplug your router could result in accidental
starting causing serious injury.
If your• router is Model No. 315.175060, before
installing/removing cutters, you must remove one
of the chip shields from router base.
•A spindle lock is located on the front of the motor
housing. To activate lock, push spindle lock in and slide
into lock position. See Figure 2.
WARNING:
ITo prevent damage to the spindle or spindle lock,always
Iallow motor to come to a complete stop before engaging
Lspindle lock.
•Place your router upside down on table, then turn collet
nut with wrench until lock mechanism interlocks. See
Figure 3.
NOTE: Spindle lock is spring loaded and will snap into
position when lock mechanism interlocks.
WARNING:-
If you are changing a cutter immediately after use, be
careful notto touch the cutter or collet with your hands or
fingers. They willget bumed because of the heat bu.j!dup
from cutting. Always use the wrench provided.
I
•Remove cutters by'_uming collet nut counterclockwise
enough to allow cutter to slip easily from collet. See
Figure 3. The collet is machined to precision tolerances
to fit cutters with 114in. diameter shank size.
• " COLLET
CUTTER NUT
",
" " !
TO TIGHTEN
COLLETNUT Fig. 3 •
ik,,,,
interlocking mechanism of the spindle lock will not let
you turn your router on.
•Replace chip shield on Model No. 315.175060.
i
•With your muter still upside down on table, insert shank
of cutter into collet. The shank of your Cutter should be
close to but not touching bottom of collet.
•Tighten the collet nut securely by turning clockwise
.,._with_be wrench provided. See Figure 3. Push spindle
lock in and slide into unlock position. Otherwise, the
WARNING:
Do not use cutters with undersized shanks. Undersized
shanks will nottighten properly and could be thrown from
tool causing injury.
i
Page 10
DEPTH OF CUT ADJUSTMENTS
See Figures 4, 5, _nd 6.
We recommend that cuts be made at a depth not exceeding
118in. and that several passes be made to reach depths of
cut greater than 118 in.
[u uooou !
Failure to unplug your router could result in accidental
starting causing serious injury.
•Place your router on a fiat surface, loosen locking
knob, and tum depth adjusting ring untilcutter is inside
-- _subbase. See Figure 4.
•Tum depth adjusting ring until tip of cutter touches fiat
surface. Tum the depth indicator ring untilthe zero lines
up with the indicator point on the base. NOTE: The
depth indicator dng is also a zero reset indicator when
setting cutter at zero depth of cut, then it becomes the
depth adjusting ring. See Figure 5.
•Position your router so that the cutter can extend below
the subbase for desired depth setting. See Figure 6.
•Tum the depth adjusting ring to obtainthe desired depth
of cut. The distance the cutter moves can be read on the
depth indicator ring. Each mark on the depth indicator
ring indicates 1116inch change in depth setting. Indicator
point is located on the base.
•Tighten locking knob securely before operating router.
Fig. 4
cUTrER ATZERO
DEPTHOF CUT
Fig. 5
Pa_e 11
DEPTH OF CUT ADJUSTMENTS WHEN
ROUTER IS MOUNTED TO A ROUTER TABLE
See Figure 7.
The depth of cut is readable from both sides of the depth
indicator ring. The bottom ring is convenient when using
your router mounted upside down to a router table. The
indicator point on the base can also be used when using
your router mounted to a router table.
Set the cutter at zero depth of cut, rotate depth indicator ring
to desired depth of cut on the scale, then tighten locking
knob securely.
VARIABLE SPEED
(MODEL NOS. 315.175050 AND 315.175060)
See Figure 8.
If your router is either one of these two models, it has a
variable speed control selector designed to allow operator
control of speed and torque limits.To increase the speed and
torque of your router, tum the variable speed controlselector
to a higher setting. Turn to a lower setting to decrease speed
and torque.
NOTE: If you do not want to use the variable speed control
selector, turn to the highest possible setting and the feature
will not be active.
PRACTICE BEFORE ACTUAL USE
If your router is Model No. 315.175050 or 315.175060, we
suggest that you practice with the vadable speed feature of
your router before installing a cutter and making cuts in
wood. Check the following before connecting your router
to power supply.
• Make sure power supply is 120 volts, 60 Hz, AC only.
•Make sure the spindle lock is in the unlocked position.
/
•Make sure the _gger is not in the lock-on position.
•Make sure there is not a cutter in the collet.
• Make sure the collet does not extend below the subbase.
•Choose the desired speed from the speed selection
chart. See Figure 8.
•Turn the variable speed control selector to the desired
setting.
•Plug your muter into power supply source. ..
•Grasp your router firmly with both hands and turn on.
MODELNOS.315.175050AND315.175060
CUTTER SIZE'
SPEEDSELECTIONCHART
POWER
HANDLE
TO DECREASE
SPEEDANDTORQUE
/
TO INCREASE
SPEEDANDTORQUE
VARIABLESPEED
CONTROLSELECTOR
Fig. 8
Page12
ROUTING .......
See Figure 9. ----
For ease of operation and maintaining proper control, your
router has two handles, one on each side of the router base.
When using your router hold it firmly with both hands as
shown infigure 9. Tum router on and let motor build to its full
speed, then gradually feed cutter into workpiece. Remain
alert and watch what you are doing. DO NOT operate router
when fatigued.
FREEHAND ROUTING
See Figure 10.
When used freehand, your router becomes a flexible and
V-ersatlletool. This flexibility makes it possible to easily rout
signs, relief sculptures, etc.
There are two basic techniques for freehand routing:.
• Routing letters, grooves, and pattems into wood. See
Figure 10.
• Routing out the background, leaving the letters or
pattem raised above the surface.
When freehand routing, we suggest the following:
•Draw or layout the pattem on workpiece.
•Choose the appropriate cutter.
NOTE: A core box or V-groove bit is often used for
routingletters and engraving objects. Straight bits and
ball millsare often used to make relief carvings. Veining
bits are used to carve small, intricate details.
•Rout the pattem in two or more passes. Make the first
pass at 25% of the desired depth of cut. This will
provide better control as well as being a guide for the
next pass.
• DO NOT rout deeper than 1/8 in. per pass or cut.
POWER
HANDLE
Fig. 9
Page 13
PROPER FEED.ING
The right feed is neither too fast nor too slow. It is the rate at
which the bit is being advanced firmly and surely to produce
a continuous spiral of uniform chips --without hogging into
the wood to make large individualchips or,onthe other hand,
to create only sawdust. If you are making a small diameter,
shallow groove in soft, dry wood, the proper feed may be
about as fast as you can travel your router along your guide
line. On the other hand, ifthe bitis alarge one, the cut isdeep
orthe wood is hard tocut, the proper feed may be a very slow
one. Then, again, a cross-grain cut may require a slower
pace than an identical with grain cut in the same workpiece.
There-is no fixed rule. You will learn by experience.., by
listening to the router motor and by feeling the progress of
each cut. If at all possible, always test a cut on a scrap piece
of the workpiece wood, beforehand.
SPEED SELECTION
(MODEL NOS. 315.175050 AND 315.175060 ONLY)
In general, if the material being cut is hard, the cutter size is
largelorthe depth of cut is deep (maximum 118in.), then your
router should be run at slower speeds. When these situa-
tions exist, turn the variable speed control selector untilthe
desired speed is reached.
NOTE: Carbide cutters cut at higher speeds than steel
cutters and should be used when cuttingvery hard materials.
RATE OF FEED
IMPORTANT: The whole "secret" of professional routing
and edge shaping lies in making a careful set-up for the cut
to be made and in selecting the proper rate of feed.
FORCE FEEDING
Clean, smooth routing and edge shaping can be done only
when the bit is revolving at a relatively high speed and is
taking very small bites to produce tiny, cleanly severed
chips. If your router is forced to move forward too fast, the
RPM of the__bit becomes slower than normal in relation to its
forward movement. As a result, the bitmust take bigger bites
as it revolves. =Bigger bites" mean bigger chips, and a
rougher finish. Bigger chips also require more power, which
could result in the router motor becoming overloaded.
Under extreme force-feeding conditions the relative RPM of
the bit can become so slow --and the bites it has to-take so
large -- that chips will be partially knocked off (rather than
fully cut off), with redOIting splintering and gouging of the
workpiece. See Figure 11.
Your Craftsman Router is an extremely high-speed tool, and
will make clean, smooth cuts if allowed to run freely without
the overload of a forced (too fast) feed. Three things that
cause =force feeding" are bitsize, depth-of_ut, and workpiece
characteristics. The larger the bit or the deeper the cut, the
more slowly the router should be moved forward. If the wood
is very hard, knotty, gummy or damp, the operation must be
"_q!_ed:b-'tillmore.
TOO FAST
TOO SLOW Fig. 11
You can always detect "rome feeding" by the sound of the
motor. Its high-pitched whine will sound lower and stronger
as it loses speed. Also, the strain of holding the tool will be
noticeably increased.
TOO SLOW FEEDING
It is also possible to spoil a cut by moving the router forward
too slowly. When it is advanced into the work too slowly, a
revolving bit does not dig intonew wood fast enough to take
a bite; instead, it simply scrapes away sawdust-like par-
ticles. Scraping produces heat, which can glaze, bum, or
mar the cut--in extreme cases, can even overheat the bit so
as to destroy its hardness.
In addition, it is more difficultto control a router when the bit
is scraping instead ofcutting. With practically no load on the
motor the bit will be revolving at close to top RPM, and will
have a much greater than normal tendency to bounce offthe
sides of the cut (especially, if the wood has a pronounced
grain with hard and soft areas). As a result,the cut produced
may have dppled, instead of straight sides. S_eeFigure 11.
='l'oo-slow feeding" can also cause your router to take off in
awrong direction from the intended line of cut. Always
grasp and hold your router firmly with both hands when
rouUng.
You can detect'too-slow feeding" by the runaway too-highly
pitched sound of the motor; or by feeling the "wiggle" of the
bit in the cut.
Page 14
DEPTH OF CUT
As previously mentioned, the depth of cut is important
because it affects the rate of feed which, in turn, affects the
quality of a cut (and, also, the possibility of damage to your
router motor and bit). Adeep cut requires a slower feed than
a shallow one, and a too deep cut will cause you to slow the
feed so much that the bit is no longer cutting, it is scraping,
instead.
Making a deep cut is never advisable. The smaller bits
especially those only 1/16 inch in diameter -- are easily
broken off when subjected to too much side thrust. A large
enough bit may not be broken off, but if the cut is too deep a
roughcut will resultE and it may be very difficultto guide and
control the bitas desired. For these reasons, we recommend
that you do not exceed 1/8 inch depth of cut ina single pass,
regardless of the bit size or the softness or condition of the
workpiece. See Figure 12.
To make deeper cuts it is therefore necessary to make as
many successive passes as required, lowering the bit 1/8
inch for each new pass. In order to save time, do all the
cutting necessary at one depth setting, before lowering the
bit for the next pass. This will also assure a uniform depth
when the final pass is completed. See Figure 13.
DIRECTION OF FEED AND THRUST
The router motorand bit revolve ina clockwise direction. This
gives the tool a slight tendency to twist (in your hands) in a
counterclockwise direction, especially when the motor is
starting up.
Because ofthe extremely high speed of bit rotation during a
"proper feeding" operation, there is very little kickback to
contend with under normal conditions. However, should the
bit strike a knot, hard grain, foreign object, etc. that would
affect the normal progress of the cutting action, there will be
aslight kickback-- sufficientto spoilthe trueness of your cut
if you are not prepared. Such a kickback is always in the
direction opposite to the direction of bit rotation.
Toguard ag._itlst such a kickback, plan your set-up and
direction of feed so that you will always be thrusting the tool
to hold it against whatever you are using to guide the cut
min the same direction that the leading edge of the bit is
moving. Inshod, the thrust should be ina directionthat keeps
the sharp edges of the bit continuously biting straight into
new (uncut) wood. _
2ND.
PASS
1ST.
PASS 2ND. PASS
1-_i"1 1ST. PASS
__._Rg. 13
GUIDE OUTSIDE
ROTATI_..,.__ON _"_1_,i_
J_-I line • i
""''" FEED
__ GUID
THRUST'_ FE'ED
GUIDE INSIDE Fig. 14
ROUTING
Whenever you are routinga groove, your travel should be in
a direction that places whatever guide you are using at the
right-hand side. In shod, when the guide is positioned as
shown in the first part of Figure 14, tool travel should be left
to dght and counterclockwise around curves. When the
guide is positioned as shown in the secondpart of Figure 14
tool travel should be right to left and clockwise around
curves. If there is a choice, the first set-up is generally the
easiest to use. In either case, the sideways thrust you use is
against the guide.
Page15
STARTING AND ENDING A CUT
INTERNALROUTING
Tilt router and place on workpiece, letting edge of subbase
contact workpiece first. Be careful notto let router bitcontact
workpiece. Turn router on and let motor buildto itsfullspeed.
Gradually feed cutter into workpiece until subbase is level
with workpiece.
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
i i
Upon completion of cut, turn motor off and let it come to a
complete stop before removing router from work surface.
WARNING:
Never pull router out of work and place upside down on
work surface before the cutter stops.
i
EDGING WITH PILOT BITS
The arbor-type bits with pilots are excellent for quick, easy,
edge shaping of any workpiece edge that iseither straight or
curved at a curvature as great or greater than the radius of
the bit to be used. The pilot prevents the bit from making too
deep acut; and holding the pilot firmly in contact with the
workpiece edge throughout prevents the cut from becoming
too shallow.
Whenever the workpiece thickness together withthe desired
depth of cut (as adjusted by router depth setting) are such
that only the top part of the edge is to be shaped (leaving at
least a 1/16 inch thick uncut portion at bottom), the pilotcan
ride against the uncut portion, which will serve to guide it.
See Figure 15. However, if the workpiece is too thin or the
bit set too low so that there will be no uncut edge to ride the
pilotagainst, an extra board to act as a guide must be placed
under the workpiece. This =guide" board must have exactly
the same contour -- straight or curved -- as the workpiece
edge. If it is positioned so that its edge is flush.with the
workpiece edge, the bit will make a full cut (in as far as the
bit radius). On the other hand, if the guide is positioned as
shown in Figure 15 (outfrom the workpiece edge), the bitwill
make less than a full cut -- which will alter the shape of the
finished edge.
NOTE: Any of the piloted bits can be used without a pilotfor
edge shaping with guides, as preceding. The size (diameter)
of the pilot that is used determines the maximum cut width
that can be made with the pilot against the workpiece edge
(the small pilot exposes all of the bit; the large one reduces
arff_unt by 1/16 inch).
ROUTER
Ii
_ , "----_.
TOPEDGESHAPING
ROUTER GUIDE
I
WORK
PILOT
WHOLE EDGE SHAPING Fig. 15
EDGE ROUTING
Place router on workpiece, making sure the router bit does
not contact workpiece. Tum router on and let motor build to
its full speed. Begin your cut, gradually feeding cutter into
workpiece.
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
Upon completion of cut, tum motor off and let it come to a
complete stop before removing router from work surface.
WARNING: -
Never pull router out of work and place upside down on
work surface before the cutter stops.
Pacle 16
ROUTING WITH GUIDE BUSHINGS
When using the Template Guide Bushings Item No. 9-25082
with your router, you must visually center the bit with the
bushing before beginning yourcut. Your routersubbase may
be adjusted by loosening the screws holding the subbase to
your router. Be sure clamping lever is locked before center-
ing bit in bushing. After centering bit with bushing, tighten
screws firmly.
WARNING:
Failure to center bit with bushing or to firmly tighten
--screwsafter centering couldcause bit to come in contact
with bushing resulting in serious injury.
k
SWITCH REPLACEMENT
ROUTER TABLES
The use of Craftsman routers on router tables offered by
other manufacturers has not been investigated for compli-
ance with applicable safety standards.
WARNING:
Do not use with router tables that fail to conform to safe
wood working practices and offer proper guarding for the
cutter. Failure tocomply can result in an accident causing
possible serious injury.
(MODEL NO. 315.175040)
See Figures 16and 17.
[] UNPLUG YOUR ROUTER.
i
[]
WARNING'.
Failure to unplug your router could result in accidental
starting causing serious injury.
Remove screws (A) and handle cover (B). See Figure
16.
[] Note the location of the molded bend relief (C) on
the power handle cord. Also note all wiring in the
handle and how each lead is connected to the
switch. Connections and wiring position must be
identical when installing new switch. See Figure 16.
-m Remove leads from switch (D) by inserting a 1/32 in.
diameter-nail or pin into switch lead receptacle and
pulling on lead as shown in figure 17. Remove nail or
pin with a twisting, pulling motion.
[]_ Make lead connections to new switch. Push each lead
as far as possible into proper switch receptacle. Pull on
leads to check lead connections with lead receptacles.
[] Locate switch in ha,_lle and place leads so they won't
be pinched or contact screws when handle cover is
replaced.
[] Make sure molded bend relief ((3) iscorrectly positioned
in switch handle, then replace handle cover and screws.
[] Tighten all screws securely.
A
C
SWITCH 1/32 IN. DIAMETER
NAIL OR PIN
Fig. 16
P_n_ 17
SWITCH REPJ.ACEMENT (CONTINUED)
(MODEL NOS. 315.175050 AND 315.175060)
See Figures 18 and 19.
[] UNPLUG YOUR ROUTER.
ii
WARNING:
| Failure to unplug your router could result in accidental
Lstart.ingcausing serious injury. i i
[] Remove screws (A) and handle cover (B). See Figure
[] Note the location of the molded bend relief (C) on
the power handle cord. Also note all wiring in the
handle and how each lead is connected to the
switch, Connections and wiring position must be
identical when installing new switch. See Figure 18.
[] Remove leads from switch (D) by inserting a 1/32 in.
diameter nail or pin into switch lead receptacle and
pulling on lead as shown in figure 19, Remove nail or
pin with a twisting, pulling motion.
•Make lead connections to new switch. Push each lead
as far as possible into proper switch receptacle. Pull on
leads to check lead connections with lead receptacles.
[] Locate switch in handle and place leads so they won't
be pinched or contact screws when handle cover is
replaced.
[] Make sure molded bend relief (C) is correctly positioned
in switch handle, then replace handle cover and screws.
[] Tighten all screws securely.
VIOLET
C
VARIABLE
SPEED "
SWITCH
Fig. 18
1/32 IN. DIAMETER
NAILOR PIN
Pa(]e 18
LIGHT BULB REPLACEMENT
See Figure 20. ""
•UNPLUGYOUR ROUTER.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
•Remove cutter from router.
•Adjust router to maximum height.
nRemove screws (A) and subbase (B). See Figure 20.
•Remove screw (C) and work light lens (D).
•With bulb (E) pointing toward you, push bulb in and
tum to the left to remove from bulb socket.
NOTE: Light bulb removal and installation is similar to
removing and installing a standard automotive bulb.
•Install new bulb by reversing the above procedure.
•Reassemble all parts and tighten screws securely.
B
E
PROPER CARE OF CUTTERS
Get faster and more accurate cutting results by keeping
cutters clean and sharp. Remove all accumulated pitch and
gum from cutters after each use.
A cutter sharpening kit (Item No. 9-66501) is available from
Sears Retail Stores.
When sharpening cutters, sharpen only the inside of the
cutting edge. Never grind the outside diameter. Be sure
when sharpening the end of a cutter to grind the clearance
angle the same as originally ground.
HELPFUL HINTS
J
J
,/
,/
,/
,/
,/
,/
,/
,/
J
J
PROPER CARE OF COLLET
From time to time, it also becomes necessary to clean your
collet and collet nut. To do so, simplyremove collet nut from
collet and clean the dust and chips that have collected. Then
retum collet nut to its odginal position.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normaloperating conditions. Therefore, nofurther lubrication
is required.
Always clamp workpiece securely before routing.
A safe operator is one who thinks ahead.
Always wear eye protection when routing..-
Make set-up adjustments carefully. Then double check. Measure twice and cut once.
Keep cutters c'l'_anand properly sharpened.
Don't let familiarity ma.ke you careless.
Study all safety rules and do the job safely.
NEVER place your hands in jeopardy.
Make certain clamps can't loosen while in use.
Test difficult set-ups on scrap mDon't waste lumber.
Plan each operation before you begin.
Clean your router frequently. This will provide smoother operation of depth adjusting ring and locking knob areas.
Shake router or blow with an air jet to remove sawdust build-up.
THINK SAFETY BY THINKING AHEAD.
Paoe 19
WARNING:
When servicing use only identical Craftsman replacement
parts. Use of any other parts may create a hazard or
cause product damage.
i
GENERAL
Only the parts shown on parts list, pages 23, 25 and 27 are
intended to be repaired or replaced bythe customer. All other
parts represent an important part of the double insulation
system and should be serviced only by a qualified Sears
service technician.
Avoid using solvents when cleaning plastic pads. I_ost
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc. come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
I•
When electric tools are used onfiberglass boats, sports cars,
wallboard, spackling compounds, or plaster, it has been
found that they are subject to accelerated wear and possible
premature failure, as the fiberglass chips and grindings are
highly abrasive to bearings, brushes, commutators, etc.
Consequently it isnot recommended that thistool be used for
extended work on any fiberglass material, wallboard,
spackling compounds, or plaster. During any use on these
materials, it is extremely important that the tool is cleaned
frequently by blowing with an air jet.
WARNING:
Always wear safety goggles, or safety glasses with side
shields during power tool operation or when blowing dust.
If operation is dusty, also wear a dust mask.
i
EXTENSION CORDS
The usa of any extension cordwillcause some loss of power.
To keep the lossto a minimumandto prevent tool overheating,
use an extension cord that is heavy enough to carry the
current the tool will draw.
A wire gage size (A.W.G.) of at least 14 is recommended for
an extension cord 100 feet or less in length. When working
outdoors, use an extension cord that is suitable for outdoor
use. The cord's jacket will be marked WA.
i
CAUTION:
Keep extension cords away from any routing area and
position the cord so that it will not get caught on lumber,
tools, etc., dudng routing operation.
i
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
i
THE FOLLOWING RECOMMENDED ACCESSORIES ARE
CURRENTLY AVAILABLE AT SEARS RETAIL STORES.
Dovetail Template
Box Joint Template
Butt Hinge Template
Multi-Purpose Router Guide
Rout -A - Form Pantograph
Sharpening Kit
Full View Router Base
COMBI-
NATION
PANEL
CUTTER
]!]] _I II IIII III]111111I '1 IIII IIIInnl'llII
VEINING STRAIGHT COMB- HINGE DOVETAIL
BIT FACE INATION MORTISING CUTTER
BIT STRAIGHT, BIT BITS
BEVEL
CUTLER
COREBOX RABBET OGEE,
BIT BIT ROMAN0
V-GROOVE
BALL
BEARINGS
(_2w.a
mw.)
I *CARBIDETIPPEDBITSI
' 2589 FORHIGHSPEEDSTEELEDGEFORMINGBITS
rlnr' InlllllJlI flrlllllll'i II IIIIII I I I !I II I IIIIIll'Jllll iHll ill IHIIII
WARNING: The use of attachments or accessories not listed above might be hazardous.
COVE BEAD ARBOR
BIT, QUARTER. 2589
45° ROUND !
CHAMFER BITS
BIT c
)aqe 21
10
I SEE NOTE "A"
3-----e
4
4
25
21
I23 22 ./
12 13 14" -1s
18
/
17
NOTE: "A" - The assembly shown represents an Important part of the Double Insulated System. To avoid the
possibility of alteration or damage to the System, service should be performed by your nearest Sears
Repair Center. Contact your nearest Sears Retail Store for Service Center Information.
Page 22
CRAFTSMAN ROUTER- MODEL NUMBER 315.175040
The model number will be found on a plate attached to the motor housing. Always mention the model number Iin all correspondence regarding your ROUTER or when ordedng repair parts.
]
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
Key Part
No. Number
1 973741-001
2 970692-001
3 989985-003
4 974722-000
5 974131-001
6 623166-006
7 622832-014
8606066-004
9 617966-030
10 970697-000
11 973735-002
12 606688-002
13 998586-001
14 612191-004
15 989684-001
16 975O41-001
17 610930-002
18 970696-000
19 610951-001
20 998895-001
- 21 623173-006
22 999603-001
23 931744-059
24 970855-001
25 989935-006
972000-248
PARTS LIST
Description Ouan.
Data Plate ............................................................................................. 1
Label ...................................................................................................... 1
Collet Nut (1/4 in.) .................................................................................
Depth Adjusting Ring Assembly (Includes Key No. 24) ......................... 1
Depth Indicator Ring ............................................................................. 1
* Square Head Bolt (#1/4-20 x 1-1/4 in.)..._. ............................................ 1
Roll Pin ................................................................................................... 1
* Screw (#10-32 x 3/4 in. Pan Hd.) .......................................................... 4
* Screw (#8-10 x 5/8 in. Pan Hd.) ............................................................ 8
Handle Assembly .................................................................................. 1
Base ....................................................................................................... 1
Chip Shield ............................................................................................ 1
* Screw (#10-32 x 1/4 in. Pan Hd.) .......................................................... 3
Subbase ................................................................................................. 1
*Screw (#6-32 x 1/4 in. T.C. Pan Hd.) .................................................... 1
Work Ught Lens .................................................................................... 1
Light Housing ........................................................................................ 1
Power Handle Assembly ....................................................................... 1
Light Bulb .............................................................................................. 1
Switch .................................................................................................... 1
Wire Nut ................................................................................................. 1
Knob ....................................................................................................... 1
Washer ................................................................................................... 3
*Screw (#5-20 x 3/8 in. Hi-Lo Fil. Hd.) .................................................... 2
Wrench (9/.1.6in.) .................................................................................. 1
Owner's Manual
* Standard Hardware Item - May Be Purchased Locally
:_,
Page 23
..... CRAFTSMAN ROUTER - MODEL NUMBER 315,175050 ,
SEE NOTE "A"
9
27 28
10
I 26 25 22
18
21
9
w_
t
NOTE: "A" - The assembly shown _presents an important part of the Double Insulated System. To avoid the
__-. possiblllty of alteration or damage to the System, service should be performed by your nearest Sears
Repslr Center. Contact your nearest Sears Retail Store for Servlce Center information.
Page 24
•CRAFTSMAN ROUTER - MODEL NUMBER 315.175050 .
J .-Themodelnumberwillbefoundonaplateattachedtothemotorhousing. Always mention the model number J
in all correspondence regarding your ROUTER or when ordering repair parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
Key Part
No. Number
1 973742-001
- 2 •970692-001
3 989985-003
4 974722-000
5 974131-001
6 623166-006
7 622832-014
8 606066-004
9 617966-030
10 970697-000
11 973735-002
12 606688-002
13 998586-001
14 612191-004
15 989684-001
16 975041-001
17 990822-002
18 610930-002
19 970793-007
20 970793-008
- 21 970698-000
-22 623173-006
23 999895-002
24 610951-001
25 999603-001
26 931744-059
27 9"70855-001
28 989935-006
972000-248
PARTS LIST
Description Quan.
Data Plate ............................................................................................. 1
Label.................._.............._.__...................................._......................_.....1
Collet Nut (1/4 in.) ................................................................................. 1
Depth Adjusting Ring Assembly (Includes Key No. 27) ......................... 1
Depth Indicator Ring ............................................................................. 1
* Square Head Bolt (#1/4-20 x 1-1/4 in.) .................................................. 1
Roll Pin ................................................................................................... 1
* Screw (#10-32 x 3/4 in. Pan Hd.) .......................................................... 4
*Screw (#8-10 x 5/8 in. Pan Hd.) ............................................................ 8
Handle Assembly .................................................................................. 1
Base ....................................................................................................... 1
Chip Shield ............................................................................................ 1
°Screw (#10-32 x 1/4 in. Pan Hd.) .......................................................... 3
Subbase ................................................................................................. 1
° Screw (#6-32 x 1/4 in. T.C. Pan Hd.) ........................ ............................ 1
Work Ught Lens .................................................................................... 1
Variable Speed Control Selector ........................................................... 1
Ught Housing ................................. ._...................................................... 1
Red Lead .............................................................................................. 1
Red Lead .............................................................................................. 1
Power Handle Assembly ....................................................................... 1
Wire Nut .................................................................................................. 1
Switch .................................................................................................... 1
Ught Bulb .............................................................................................. 1
Knob................................................................_..............._......................_
Washer ................................................................................................... 3
*Screw (#5-20 x 3/8 in. Hi-Lo RI. Hd.). ...................................... ..-...... _....2
Wrench (9/16 in.) .................................................................................. 1
Owner's Manual
* Standard Hardware Item - May Be Purchased Locally
Page 25
CRAFTSMAN ROUTER -MODEL NUMBER 315.175060
[ The model number will be found on a plate attached to the motor housing. Always menUon the model number il_all correspondence regarding your]ROUTER or when ordering repair parts.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
PARTS LIST
Key Part
No. Number Description Quan.
1 989985-003
2 970692-002
3 607433-003
4 610958-001
5 970517-004
6 617966-031 *
7 622931-007 *
8 973743-001
9 989935-006
10 706404-004 *
11 974722-000
Collet Nut (1/4 in.) ......................................... 1
Label ............................................................. 1
Spacer ........................................................... 1
Blower ........................................................... 1
End Cap ........................................................ 1
Screw (#8-10 x 3/4 in. Pan Hd.) .................... 3
Screw (#6-32 x 1-5/16 in. Fil. Hd.) ................ 1
Data Plate ..................................................... 1
Wrench (9/16 in.) .......................................... 1
Hex Nut (#6-32) **STD541006 ..................... 1
Depth Adjusting Ring Assembly
(Includes Key No. 35) ................................... 1
Vacuum Hose ............................................... 1
Depth Indicator Ring ..................................... 1
Square Head Bolt (#1/4-20 x 1-1/4 in.)., ....... 1
Roll Pin .......................................................... 1
Screw (#10-32 x 3/4 in. Pan Hd.) .................. 4
Screw (#8-10 x 5/8 in. Pan Hd.) .................... 8
Handle Assembly .......................................... 1
* Standard Hardware Item _May Be Purchased Locally
12 610966-002
13 974131-001
14 6231.66-006 *
15 622832-014
16 606066-004 *
17 617966-030 *
18 970699-000 !
I
Key Part
No. Number Description Quan.
19 973735-204
20 606688-002
21 998586-001
22 612191-004
23 989684-001
24 975041-001
25 990822-002
26 610930-002
27 970793-007
28 970793-008
29 970698-000
30 610951-001
31 998895-002
32 999603-001
33 931744-059
34 623173-006
35 970855-001
36 971788-003
972000-248
Base .............................................................. 1
Chip Shield ................................................... 2
* Screw (#10-32 x 1/4 in. Pan Hd.) .................. 3
Subbase ........................................................ 1
* Screw (#6-32 x 1/4 in. T.C. Pan Hd.) ............ 1
Work Light Lens ............................................ 1
Variable Speed Control Selector .................. 1
Light Housing ................................................ 1
Red Lead ...................................................... 1
Red Lead ...................................................... 1
Power Handle Assembly ............................... 1
Light Bulb ...................................................... 1
Switch ........................................................... 1
Knob .............................................................. 1
Washer .......................................................... 3
Wire Nut ........................................................ 1
* Screw (#5-20 x 3/8 in.,Hi-Lo Fil. Hd.) ............ 2
Dust Bag Assembly ...'................................... 1
Owner's Manual
** Available From Div.98 -- Source 980.00
Page 27
Forthe repairorreplacementpartsyouneed
delivereddirectlyto yourhome
Call7 am- 7 pro,7 daysaweek
1-800-366-PART
(1-800-366-7278)
Forrepairservice
Call24 hoursa day,7 daysa week
1-800-4-REPAIR
(1-800-473-7247)
P,EPAIRSERVICES
Forthelocationofa
SearsPartsandRepairCenterinyourarea
Call24 hours a day,7 daysa week
1-800-488-1222
m
ImBB
Elm
SEARS
b
IBEBBBE,,,,..'-'-
The modelrjumberofthistoolwill beroundona serial plate
attachedto the motorhousing.Whenrequestingserviceor
orderingpads, alwaysprovidethe followinginformation:
• ProductName • MOdelNumber
Router 315.175040
315.175050
315.175060
SE/AJ:I$
_PartName • Part Number America's Repair Specialists

Navigation menu