Craftsman 315216260 User Manual 16IN. VARIABLE SPEED SCROLL SAW Manuals And Guides L9050206

CRAFTSMAN Saw Scroll Manual L9050206 CRAFTSMAN Saw Scroll Owner's Manual, CRAFTSMAN Saw Scroll installation guides

ROLLCAGE B5115-0920 L9050206

User Manual: Craftsman 315216260 315216260 CRAFTSMAN 16IN. VARIABLE SPEED SCROLL SAW - Manuals and Guides View the owners manual for your CRAFTSMAN 16IN. VARIABLE SPEED SCROLL SAW #315216260. Home:Tool Parts:Craftsman Parts:Craftsman 16IN. VARIABLE SPEED SCROLL SAW Manual

Open the PDF directly: View PDF .
Page Count: 26

Owner's Manual

II:RRFTSMRNI

16 in, variable speed

SCROLL SAW

Model No.

315.216260

Save this manual for

future reference.

CAUTION: Read and

follow all Safety Rules and

Operating Instructionsbefore

first use of thisproduct.

Customer Help Line

1-800-932-3188

•Safety

• Features

•Adjustments

•Operation

•Maintenance

•Parts List

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

VisLt the Craftsman web page: www.sears,com/craftsrnan

97200O-549

7-98

NRTL/C

•Table of Contents ........................................................................................................................................... 2

•Warranty and Introduction.............................................................................................................................. 2

•Rules For Safe Operation ......................................................................................................................... 3-5

•Electrical.......................................................................................................................................................... 6

•Glossary and ProductSpecifications ............................................................................................................. 7

•Unpacking and Tools Needed ........................................................................................................................ 8

• Labels ............................................................................................................................................................. 9

•Features .................................................................................................................................................. 10-11

•Assembly ................................................................................................................................................. 11-12

•Adjustments ............................................................................................................................................. 12-15

•Operation ................................................................................................................................................. 16-19

•Maintenance ............................................................................................................................................ 19-20

•Troubleshooting............................................................................................................................................ 20

•Exploded View and Repair Parts List...................................................................................................... 22-25

•Parts Ordering /Service ............................................................................................................................... 26

FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW

If this rRRFTSMRN" Scroll Saw fails due to a defect in material or workmanship within one year from the date of

purchase, Sears will repair it, free of charge.

Contact a Sears Service Center for repair.

If this product is used for commercial or rental purposes, thiswarranty applies only for 90 days from the date of

purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Your saw has many features for making cutting

operations more pleasant and enjoyable. Safety,

performance and dependability have been given top

priorityin the design of this saw making it easy to

maintain and operate.

_I, CAUTION: Carefully read throughthis entire

owner's manual before usingyour new saw. Pay

close attention to the Rules For Safe Operation,

and all Safety Alert Symbols includingDanger,

Warning and Caution. If you use your saw

properly and only for what it is intended, you will

enjoy years of safe, reliable service.

_. Look for this symbol to point out important safety precautions. It means attention!H Your

safety is involved.

_IL WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes,

which can result in severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield when needed. We

recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses

with side shields, available at Sears Retail Stores.

Thepurposeof safetysymbolsIs to attract your attention to possible dangers. The safety symbols, and

the explanations with them, deserve your careful attention and understanding. The safety warnings do

not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for

proper accident prevention measures.

SYMBOL

MEANING

SAFETY ALERT SYMBOL:

Indicates danger, warning or caution. May be used in conjunctionwith other symbols or picto-

graphs.

DANGER: Failure to obey a safety waming will result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

,a, WARNING: Failure to obey a safety warning can result in serious injuryto yourselfor to others.

Always follow the safety precautionsto reduce the riskof fire, electric shockand personal injury.

Note:

CAUTION: Failure to obey a safety warning may result in property damage or personal injuryto

yourself orto others. Alwaysfollow the safety precautionsto reduce the riskof fire, electric shock

and personal injury.

Advises you of information or instructionsvital to the operation or maintenance of the equipment.

IMPORTANT

Servicing requires extreme care and knowledge of the system and should be performed only by a qualified

service technician. For service we suggest you return the tool to your nearest Sears store for repair. Always use

original factory replacement parts when servicing.

_lb WARNING: Do not attempt to operate this tool

untilyou have read thoroughly and understand

completely all instructions,safety rules, etc.

contained in this manual. Failure to comply can

result in accidents involvingfire, electric shock,

or serious personal injury. Save 6wner's manual

and review frequently for continuingsafe

operation, and instructingothers who may use

this tool.

,_ WARNING: Do not connect your scrollsaw to a

power source untilyou have assembled and

adjusted the saw as described in this manual

and have read and understood all precautions

and operating instructionsin the manual and

printed on the tool.

READ ALL INSTRUCTIONS

• KNOW YOUR POWER TOOL. Read the owner's

manual carefully. Learn the saw's applications

and limitationsas well as the specific potential

hazards related to this tool.

•GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH

GROUNDED SURFACES. For example; pipes,

radiators, ranges, refrigerator enclosures.

• KEEP GUARDS IN PLACE and in good working

order.

•REMOVE ADJUSTING KEYS AND

WRENCHES. Get in the habit of checking to see

that hex keys and adjustingwrenches are

removed from tool before turning on the saw.

•KEEP THE WORK AREA CLEAN. Cluttered

work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation.

•DO NOT USE IN DANGEROUS ENVIRON-

MENTS. Do not use power tools near gasoline or

other flammable liquids, in damp or wet loca-

tions, or expose them to rain. Keep the work

area well lit.

•KEEP CHILDREN AND VISITORS AWAY. All

visitorsshould wear safety glasses and be kept s

safe distance from work area. Do not let visitors

contact tool or extension cord while operating.

•MAKE WORKSHOP CHILD-PROOF with

padlocks and master switches or by removing

starter keys,

•DO NOT FORCE THE TOOL. It will do the job

better and safer at the rate for which it was

designed.

•USE THE RIGHT TOOL. Do not force the tool or

attachment to do a job it was not designed for.

Don't use it for a purpose not intended,

RULES FOR SAFE OPERATION (Continued)

mU_E THE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

When usingan extension cord, be sure to use

one heavy enough to carry the current your

product will draw. An undersized cord will cause

a drop in line voltage resultingin'loss of power

and overheating. A wire gage size (A.W.G.) of at

least 18 is recommended for an extension cord

25 feet or less in length. If in doubt, use the next

heavier gage. The smaller the gage number, the

heavier the cord.

INSPECT EXTENSION CORDS PERIODI-

CALLY and replace if damaged.

DRESS PROPERLY. Do not wear loose clothing,

gloves, neckties, rings, bracelets, or other

jewelry. They can get caught and draw you into

moving parts. Rubber gloves and nonslip foot-

wear are recommended. Also wear protective

hair covering to contain long hair.

ALWAYS WEAR SAFETY GLASSES WITH

SIDE SHIELDS. Everyday eyeglasses have only

impact-resistant lenses; they are NOT safety

glasses.

PROTECT YOUR LUNGS. Wear a face or dust

mask if the cutting operation is dusty.

PROTECT YOUR HEARING. Wear hearing

protectionduring extended periods of operation.

SECURE WORK. Use clamps or a vise to hold

work when practical. It's safer than usingyour

hand and it frees both hands to operate tool.

•DO NOT OVERREACH. Keep proper footing and

balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools

sharp and clean for better and safer perfor-

mance. Follow instructionsfor lubricatingand

changing accessories.

DISCONNECT ALL TOOLS. When not in use,

before servicing,or when changingattachments,

blades, bits, cutters, etc., all tools should be

disconnected from power supply.

AVOID ACCIDENTAL STARTING. Be sure

switch is off when pluggingin.

USE RECOMMENDED ACCESSORIES. The

use of improper accessories may cause riskof

injury.

NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the blade is unin-

tentionallycontacted.

CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function. Check for alignment of moving parts,

bindingof movingparts, breakage of parts, saw

stability,mounting and any other conditions that

may affect its operation. A guard or other part

that is damaged must be properly repaired or

replaced by a qualified service technician at a

Sears store to avoid risk of personal injury.

DIRECTION OF FEED. Feed work into a blade

or cutter against the direction of rotation of the

blade or cutter only.

NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN THE POWER OFF. Do not

leave tool until it comes to a complete stop.

USE ONLY CORRECT BLADES. Use the right

blade size, style and cuttingspeed for the

material and the type of cut. Blade teeth should

pointdown toward the table. Sharp blades

minimize stalling and kickback. Correctly adjust

blade tension.

TO PROTECT THE OPERATOR and minimize

blade breakage, ALWAYS adjust the hold down

foot to just clear the workpiece. Never operate

the saw with any guard or cover removed. Make

sure all guards are operating properly before

each use.

KEEP HANDS AWAY FROM CUTTING AREA.

Do not hand hold pieces so small that your

fingers go under the blade guard. Never reach

underneath work or behind, under, or within

three inches of the blade and its cutting path with

your hands and fingers for any reason. Do not

attempt to remove cut material when blade is

moving.

,_k WARNING: Blades coast after turn off.

•AVOID PINCHING THE BLADE. Be cautious

when cuttingoff material which is irregularin

cross section. For example, molding must lay flat

on the table and not be permitted to rock.

•DO NOT ABUSE CORD. Never yank cord to

disconnect it from receptacle. Keep cord from

heat, oil, and sharp edges.

•INSPECT TOOL CORDS PERIODICALLY and if

damaged, have repaired by a qualified service

technician at a Sears store. Stay constantly

aware of cord location and keep it well away

from the rotating blade.

•DO NOT USE TOOL IF SWITCH DOES NOT

TURN IT ON AND OFF. Have defective switches

replaced by a qualified service technician at a

Sears store.

RULES FOR SAFE OPERATION (Continued)

KEEP TOOL DRY, CLEAN, AND FREE FROM

OIL AND GREASE. Always use a clean cloth

when cleaning. Never use brake fluids, gasoline,

petroleum-based products,or any solvents to

clean tool

A LARGE PIECE OF MATERIAL SHOULD BE

SUPPORTED while cutting. To minimize riskof

blade pinching and kickback, always support

long workpieces. Saw may slip, walk or slide

while cutting long or heavy boards.

BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

BEFORE CHANGING THE SETUP, REMOVING

COVERS, GUARDS OR BLADE, UNPLUG THE

SAW, AND REMOVE THE SWITCH KEY.

•DO NOT FEED THE MATERIAL TOO QUICKLY

while cutting. Do not force the workpiece against

the blade.

•NEVER CUT MORE THAN ONE WORKPIECE

AT A TIME. If making a stacked cut, all of the

pieces must be secured to each other with

masking tape or double stick tape to make one

workpiece. Do not put more than one workpiece

on the saw table at a time. Always hold the work

firmly against the table. See page 18.

•AVOID CU'I-FING NAILS. Inspect for and

remove all nails from lumber before cutting.

•NEVER PERFORM LAYOUT, ASSEMBLY, OR

SETUP WORK ON THE TABLE while the

cutting tool is operating.

•NEVER TOUCH BLADE or other moving parts

during use,

•NEVER START A TOOL WHEN THE BLADE IS

IN CONTACT WITH THE WORKPIECE. Clear

the table of debris before turning your scrollsaw

on,

ALLOW THE MOTOR TO COME UP TO FULL

SPEED before starting a cut.

FIRMLY CLAMP OR BOLT your scrollsaw to a

firm, level workbench or table. The most comfort-

able saw table height is at approximately hip

height.

•AVOID AWKWARD OPERATIONS A_D HAND

POSITIONS where a sudden slip could cause

your hand to move into the blade. ALWAYS

make sure you have good balance. Do not cut

pieces of material that are too small to hold

comfortably in your hand.

•REPLACEMENT PARTS. All repairs, whether

electrical or mechanical, should be made by

qualified service technician at a Sears store or

repair center.

_1= WARNING: When servicing use only identical

Craftsman replacement parts. Use of any other

parts may create a hazard or cause product

damage.

•NEVER USE IN AN EXPLOSIVE ATMO-

SPHERE. Normal sparking of the motor could

ignitefumes.

•DO NOT OPERATE THIS TOOL WHILE UN-

DER THE INFLUENCE OF DRUGS, ALCOHOL,

OR ANY MEDICATION.

STAY ALERT AND EXERCISE CONTROL.

Watch what you are doing and use common

sense. Do not operate tool when you are tired.

Do not rush.

•MAKE SURE THE WORK AREA HAS AMPLE

LIGHTING to see the work and that no obstruc-

tions will interfere with safe operation BEFORE

performing any work using your saw.

•ALWAYS TURN OFF SAW before disconnecting

it, to avoid accidental starting when reconnecting

to power supply. NEVER leave the scrollsaw

unattended while connected to a power source.

_. WARNING: Do not allow familiarity with your

saw make you careless. Remember that a

careless fractionof a second is sufficientto inflict

severe injury.

SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instructother users. If you

loan someone thistool, loan them these instruc-

tions also.

SAVE THESE INSTRUCTIONS

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong

grounding plugs and 3-pole receptacles that accept

the tool's plug. When using a power tool at aconsider-

able distance from the power source, use an exten-

sion cord heavy enough to carry the current that the

tool will draw. An undersized extension cord will

cause a drop in line voltage, resulting in a loss of

power and causing the motor to overheat. Use the

chart provided below to determine the minimum wire

size required in an extension cord. Only round jack-

eted cords listed by Underwriter's Laboratories (UL)

should be used.

Length of Extension Cord

Up to 25 feet

Wire Size (A.W.G.)

26-100 feet 16

When working with the tool outdoors, use an exten-

sion cord that is designed for outside use. This is

indicated by the letters WA on the cord's jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

_i, CAUTION: Keep the cord away from the cutting

area and position the cord so that it will not be

caught on lumber, tools, or other objects during

cutting.

GROUNDING

PIN COVEROF GROUNDED

OUTLETBOX

Fig. 1

ELECTRICAL CONNECTION

Your Sears Craftsman Scroll Saw is powered by a

precision built electric motor. It should be connected

to a power supply that Is 120 volts, 60 Hz, AC only

(normal household current). Do not operate this tool

on direct current (DC). A substantial voltage drop will

cause a loss of power and the motor will overheat. If

the saw does not operate when plugged into an outlet,

double check the power supply.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current

to reduce the risk of electric shock. This tool is

equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug

must be plugged into a matching outlet that is propedy

installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician. Improper connection of the equipment-

grounding conductor can result in arisk of electric

shock. The conductor with insulation having an outer

surface that is green with or without yellow stripes is

the equipment-grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to

a live terminal.

Check with a qualified electrician or service personnel

if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is

properly grounded.

Repair"or replace a damaged or worn cord immedi-

ately.

"This tool is intended for use on a circuit that has an

outlet like the one shown in Figure 1. It also has a

grounding pin like the one shown.

Bevel Cut

A cutting operation made with the table at any angle

other than 90" to the blade.

Crosscut

A cutting or shaping operation made across the grain

of the workpiece.

Compound Cut

A compound cut is a cut made using amiter angle

and a bevel angle at the same time.

Freehand (for scroll saw)

Performing a cut without the workpiece properly

supported on the table.

Gum

A sticky, sap based residue from wood products.

Kerr

The matedal removed by the blade in a through cut or

the slot produced by the blade in a nonthrough or

partial cut.

Leading End

The end of the workpiece pushed into the cutting tool

fimt.

Miter Cut

A cutting operation made with the saw table at an_

angle other than 90" to the blade.

Nonferrous Metal

Metal that does not contain iron; such as aluminum,

brass, and copper.

Push Stick

A device used to feed the workpiece through the saw

blade during narrow ripping type operations and helps

keep the operator's hands well away from the blade.

Resaw

A cutting operation to reduce the thickness of the

workpiece to make thinner pieces.

Resin

Asticky, sap base substance that has hardened.

Ripping

A cutting operation along the length of the workpiece.

Saw Blade Path

The area directly in line -- over, under, behind, or in

front of the blade. AS it applies to the workpiece, that

area which will be, or has been, cut by the blade.

Set

The distance that the tip of the saw blade tooth is bent

(or set) outward from the face of the blade.

SPM

Strokes per minute. Used in reference to blade

movement.

Throw-Back

Throwing of a workpiece in a manner similar to a

kickback. Usually associated with a cause other than

the kerr closing, such as a workpiece not being

against the fence, being dropped into the blade, or

being placed inadvertently in contact with the blade.

Through Sawing

Any cutting operation where the blade extends

completely through the thickness of the workpiece.

Workpiece

The item on which the cutting operation is being done.

The surfaces of a workpiece are commonly referred to

as faces, ends, and edges.

Worktable

The surface on which the workpiece rests while

performing a cutting or sanding operation.

Throat

Motor

Drive

Blade Length

Table Size

16 in.

120 V, 1.2 amp 60 HZ-AC only

Variable Speed

500-1700 Strokes per minute

5 in. plain or pin

10-1/4 in. x 12 in.

Table Tilt

Overall Dimensions

Net Weight

47" right and 12" left

12in. W

24-1/2 in. L

14in. H

27.5 lb.

,_ WARNING: To prevent accidental startingor

electrical shock that could cause possible

serious personal injury,assemble all parts to

your saw before connecting it to power supply.

Saw should never be connected to power supply

when you are assembling parts, making

adjustments, lubricating, installingor removing

blades, cleaning, or when not in use.

Carefully lift saw from the carton and place it on

a level work surface.

Remove pack of 4extra blades and owner's

manual from the carton.

_, WARNING: If any parts are missing, do not

operate this tool untilthe missing parts are

replaced. Failure to do so could result in possible

serious personal injury.

•Do not discardthe packing materials until you

have carefully inspected the saw, identifiedall

pads, and satisfactorily operated your new saw.

Note: If any parts are damaged or missing, do not

attempt to plug in the power cord and turn the switch

on untilthe damaged or missingparts are obtained

and are installed correctly.

Your scroll saw comes completely assembled. A

package of 4 extra blades and an owner's manual are

includedwith your saw.

The following tools (not included) are needed for

adjustments and alignment:

•Small Combination Square

•Adjustablewrench

•Flatblade Screwdriver

SMALL

COMBINA_ON

SQUARE

FLATBLADESCREWDRIVER Fig. 2

The following labels are on the scrollsaw with locations indicated.

WARNING

ADVERTENCIA

ON OFF

II:RRFTSMAN1

Customer Help Line 1-800-932-3188

WARNING IADVERTENCIA

Fig. 3

Thisversatilevariablespeedscrollsawisgreatfor

making toys, puzzles, games, artwork, and jewelry. It

is a handy do-it-yourself tool. It cuts wood, wood

composition products, plastic, and other fibrous

material up to 2inches thick. It also cuts nonferrous

metals (aluminum, brass, copper).

KNOW YOUR SCROLL SAW

Before attempting to use your saw, familiarize yourself

with all operating features and safety requirements of

your Sears Craftsman scrollsaw. See Figure 5.

ON/OFF KNOB WITH VARIABLE SPEED

Your scroll saw has an easy access ON/OFF knob

with variable speed. Pull the knob out to turn ON the

saw, and push the knob in to turn OFF the saw. Turn

the knob to adjust the speed from the high speed of

approximately 1700 SPM (Strokes Per Minute) to the

low speed of approximately 500 SPM.

LOCK OFF POST

Place a pad lock in the lock post next to the ON/OFF

knob to look the saw in the OFF positionto prevent ,

unauthorized use of the saw by children or others.

TOOLLESS BLADE HOLDERS

Retain and positionthe blade without the use of

additional tools. Use the knobs for plain end blades or

use the designed slotsfor pin type blades.

TENSION QUICKRELEASE

ADJUSTING KNOB

KNOB

BLADE

DRAWER

Fig. 4

BLADE STORAGE DRAWER

Attached under the left side of the table is ablade

storage drawer. It will hold up to 20 blades. Drawer

snaps closed securely. See Figure 4.

BLADE TENSION KNOBS

Blade tension is controlled by a dual knob tension

control system. The inner (smaller) knob, tension

adjusting knob, is for making adjustments of the blade

tension. The outer (larger) knob, quick release knob,

is used to quicklyset and release blade tension to

facilitate blade changes,

AIRDIAPHRAGM

HOLDDOWNFOOTLOCKKNOB

PLAINENDBLADEKNOB

HOLDDOWNFOOT/

GUARD

SAWBLADE

SAWTABLE

MITERSCALE

MOTOR BEVELADJUSTMENTKNOB

LOCKOFFPOS'I'

ON/OFFKNOB

Fig. 5

HOLD DOWN FOOT/BLADE GUARD

The hold down foot should be lowered until it just

rests on top of the workpiece to prevent the workpiece

from lifting while cutting, but not so much that the

workpiece drags. The vertical portion provides a blade

guard to prevent accidental blade contact.

HOLD DOWN FOOT LOCK KNOB

Allows you to raise or lower the hold down foot/blade

guard and secure it at desired heights•

SAWDUST BLOWER

Keeps the line of cut on workpiece clean for more

accurate scroll cuts.

SAWDUST EXHAUST

Your saw has a sawdust exhaust that fits a standard

shop vacuum hose. See Figure 13.

SAW TABLE

Your scrollsaw has an aluminum saw table that

provides a working surface to support your workpiece.

TABLE LOCK KNOB

Allowsyou to tilt the table and lock it at the desired

angle up to 45 degrees.

BEVEL SCALE

The bevel scale and indicator are located on the front

of the saw for easy viewing. They show the angle of

the table•

ZERO DEGREE STOP FOR TABLE

Located under the front of the saw table, the zero

degree stopallows easy returnand fine adjustment of

the zero degree relationshipbetween the table and

the blade.

Your Craftsman 16 in. scroll saw was fully assembled

at the factory. Before operating thistool, it is important

to check all alignments and settings. Normal handling

during shipment may have changed settings.

_L WARNING: To avoid serious personal injury

from unexpected tool movement, always

securely mount scroll saw to a workbench.

MOUNTING SCROLL SAW TO

WORKBENCH

See Figure 6.

If the scroll saw is to be used in a permanent applica-

tion, we recommend that you secure it in apermanent

location such as a workbench. When mountingthe

saw to aworkbench, holes should be drilledthrough

the supportingsurface of the workbench usingdimen-

sions illustrated.

•Each hole inthe base ofthe saw should be

bolted securely using 3/8 in. diameter machine

bolts, lock washers, and hex nuts (not included).

Bolt length should be 1-1/4 in. plus the thickness

of the bench top.

•Locate and mark the holes where scrollsaw is to

be mounted.

• Drill(3)7/16in. diameterholesthrough work-

bench.

Place scrollsaw on workbench aligning holes in

the base with holes drilled in the workbench.

Insert all three 3/8 in. bolts and tighten securely

with lock washers and hex nuts.

Note: All bolts should be inserted from the top. Install

the lockwashers and hex nutsfrom the underside of

the bench.

Supporting surface where scrollsaw is mounted

should be examined carefully after mountingto insure

that no movement during use can result. If any tipping

or walking is noted, secure workbench or supporting

surface before beginning cutting operations.

II 24 in.

7/16In.dia.

€ T'

6In.

19 1116 In.

12 In.

Fig. 6

CLAMPING SCROLLSAW TO

WORKBENCH

See Figure 7.

tfthe scrollsaw is to be used in a portable application,

we recommend that you fasten it permanently to a

mounting beard that can easily be clamped to a

workbench or other supportingsurface. The mounting

board should be of sufficientsize to avoid tippingof

saw while in use.

Mount saw to board using holes in frame as a

template for hole pattern or the diagram in

Figure 6. Locate and mark the holes where scroll

saw is to be mounted.

•Follow last three steps in previous section called

• ounUng Scroll Saw to Workbench.

Make sure mounting bolts are longenough to go

through holes in the saw frame, material being

mounted to, lock washers, and hex nuts.

Note: It may be necessary to countersink hex nuts

and washers on bettom side of mounting board.

C-CLAMP

WORKBENCH

MOUNTING

BOARD

Fig. 7

,_k WARNING: To prevent accidental startingthat

could cause possible serious personal injury,

turn off the sew and unplug before making any

adjustments.

HOLD DOWN FOOT/BLADE GUARD

See Figure 8.

The hold down should be adjusted so it contactsthe

top surface of the work being cut. Tighten adjusting

knob after adjustment has been made.

•Loosen the hold down foot lock knob.

•Move the hold down foot to the desired position.

•Tighten the hold down foot lock knob.

The tall, front part of the hold down foot acts as a

blade guard to prevent accidental contact withthe

blade.

SAWDUST BLOWER

See Figure 8.

The dust blower is designed and preset to direct air to

the most effective point on the cutting line. Be sure

holddown foot is properly adjusted to properly secure

workpiece and to properlydirect air to the cutting

surface.

•Insert hose to air diaphragm before startingthe

saw.

AIRDIAPHRAGM

HOLDDOWNFOOT

KNOB

BLADE

Fig. 8

SQUARING TABLE TO THE BLADE

See Figures 9 and 10.

• Loosen the hold down foot lock knob and move

hold down rod all the way up. Tighten knob.

•Loosen the table lock knob and move the table

until it is approximately perpendicular, or st right

angle to the blade.

•Place a small square on the table next to the

blade to check if the table is 90 degrees to the

blade. If adjustment is needed, raise or lower the

table until table is approximately 90 degrees to

the blade and securely tighten the table lock

knob.

•Loosen the screw holding the scale indicator,

move indicatorto the 0 degree mark and se-

curely tighten screw. Remember, the bevel scale

is aconvenient guide but should not be relied

upon for precision. Make practice cuts on scrap

material to determine if your angle settings are

correct.

•Adjust the hold down foot to desired positionand

securely tightenthe hold down foot knob.

HOLDDOWNROD

HOLDDOWNFOOT

LOCKKNOB

HOLDDOWN

F00T/

. SAWBLADE

TABLELOCK

KNOB

Fig. 9

SETTING THE TABLE FOR HORIZONTAL

OR BEVEL CUTTING

See Figures 10, 11 and 12.

A bevel scale is provided under the work table as a

convenient guide for setting the approximate table

angle for bevel cutting. When greater precision is

required, make practice cuts on scrap material and

adjust the table as necessary for your requirements.

An adjustable zero degree stop is provided to quickly

return the table to the zero degree setting.

•Loosen the table lock knob and push down on

the rightside of the table. If the table stopsat O',

the zero degree stop is properly set. If the table

stops somewhere other than zero, then adjust

the zero degree stop.

ZERODEGREE II I

"__ SCALE

TABLELOCK SCREW

KNOB Fig. 10

•To access the zero degree stop, loosen the table

look knob, and tilt the table with the dght side all

the way down. Just under the front of the saw

table is the zero degree stop. See Figure 11.

Loosen the hex nut and rotate the hex bolt to

raise or lower the bolt as needed to adjust the

zero degree stop. Be sure to check to see that

the table is square to the blade.

Now, by returningthe table to the zero position, the

zero degree stop provides a quick reference to the

preset position.

HEXBOLT SAWTABLE

HEXNUT

ZERODEGREE

STOPASSEMBLY

Fig.11

The zero stop assembly can be rotated to the left and

down out of the way and the table can be angled up to

12" to the left. See Figure 12.

Note: Make sure the zero degree stop is rotated all

the way down or it will contact the blade storage

drawer as you angle to the left.

Fig. 12

INSTALLING BLADES

Scroll saw blades wear out quickly and must be

replaced frequently for best cutting results. Expect to

break some blades while you learn to use and adjust

your saw. Blades generally stay sharp for 1/2 hour to

2 hours of cutting, depending on type of material and

speed of operation.

Pin End Blades

See Figure 13.

•Turn off and unplug the saw from outlet.

,_ WARNING: To avoid injury from accidental

starting, always turn off and unplug the saw

before installing, removing or replacing the

blade.

• On the top back of the saw, rotate the quick

release knob to the left or counterclockwise to

loosen blade tension. See Figure 5.

•Remove the throat plate.

•Place blade through the throat plate opening with

the teeth of the blade to the front of the saw and

pointing down toward the table. Engage the pin

into the "V" notch of the lower blade holder.

•Pull up on the blade and push down on the saw

arm to engage the upper pin in the "V" notch of

the upper blade holder.

Note: If the blade touches the hold down foot on

either side then the hold down foot must be adjusted.

•Loosen the foot adjusting knob. See Figure 13.

•To center the hold down foot around the saw

blade, slide the hold down foot to the side.

•Tighten the foot adjusting knob.

•To tension the blade, rotate the quick release

knob (outer, larger knob) 114turn to the right or

clockwise to apply tension to the blade. Fine

adjustments of the blade tension may be per-

formed using the tension adjusting knob (inner,

smaller knob) at any time, while the blade is

under tension or not.

•Replace throat plate.

Plain End •lades

See Figure 13.

•Turn off and unplug the saw from outlet.

AWARNING: To avoid injury from accidental

starting, always turn off and unplug the saw

before installing, removing, or replacing the

blade.

•On the top back of the saw, rotate the quick

release knob to the left or counterclockwise to

loosen the blade tension.See Figure 5.

•Remove the throat plate.

•Loosen the blade knobs by hand and remove the

blade.

Place new blade through the throat plate opening

in the table with the teeth of the blade to the front

of the saw and pointing down toward the table.

Next, place blade in the lower blade holder into

the slot that enlarges as you loosen the blade

knob.

Position blade and securely tighten blade knob.

Pull up on the blade and down on the saw's

upper arm to install blade into upper blade

holder.

Note: If the blade touches the hold down foot on

either side then the hold down foot must be adjusted.

•Loosen the foot adjusting knob. See Figure 13.

•To center the hold down foot around the saw

blade, slide the hold down foot to the side.

•Tighten the foot adjusting knob.

•Position blade and securely tighten blade knob.

•Turn the quick release knob to the right or

clockwise to tension the blade.

•Turn the tension adjusting knob to the right,

clockwise or to the left, counterclockwise untilthe

blade is in desired tension.

•Replace throat plate.

PLAINENDBLADE PLAINEND FOOTADJUSTING

BLADEKNOB

TO RELEASE

QUICKRELEASE

KNOB

TO ENGAGE

Fig. 14

Turn tension adjusting knob (upper, smaller

knob) to the right or clockwise to increase

tension. Turn it to the left or counterclockwise to

decrease blade tension.

Note: Adjustments of blade tension can be made at

anytime. The quick release knob can be either re-

leased or engaged while making adjustments with the

tension adjusting knob.

TENSIONADJUSTINGKNOB

PINENDBLADE HOLDDOWNFOOT TO INCREASE

TENSION

TO DECREASE

TENSION

SAWDUST

EXHAUST

PLAINEND

BLADEKNOB

Fig. 13

ADJUSTING BLADE TENSION

See Figures 14 and 15.

•Turn off and unplug the saw.

,_k WARNING: Failure to unplug your saw could

result in accidental starting causing possible

serious personal injury.

Tension adjusting knob is on the top of the saw.

See Figure 5. Rotate the quick release knob

(outer, larger knob) 1/4 turn to the left or counter-

clockwise to release blade tension.

Fig. 15

•Rotate quick release knob to the right or clock-

wise 1/4 turn to engage tension before using the

scroll saw.

Check tension by the sound the blade makes when

plucked like aguitar string. This method of adding

tension to the blade can be developed with practice

and requires knowing your scroll saw.

•Pluck the back straight edge of blade while

turning tension adjusting knob. Sound should be

a musical note. Sound becomes less flat as

tension increases. Sound decreases with too

much tension.

Note: Be careful not to over tension the blade. Too

much tension may cause blade to break as soon as

you start cutting. Too little tension may cause blade to

bend or break before teeth wear out.

Thisscrollsawisdesignedtocutwood,woodcompo-

sitionproducts,plastic,andnonferrousmetals(alumi-

num,brass,copper).

GENERAL OPERATION

Please read and understand the following items

concerning your scroll sew before attempting to use

the sew.

•There is a learning curve for each person who

wants to use this sew. Dudng that pedod of time

it is expected that some blades will break until

you learn how to use and adjust the sew.

•Allow the saw to cut material by guiding the

workpiece into the blade as it moves. Do not

force the work.

•The blade teeth cut matedal only on the down

stroke.

You must guide the workpiece into the blade

slowly because the teeth of the blade are very

small and can only remove matedal on the down

stroke.

•Scroll saw blades wear out and must be replaced

frequently for best cutting results.Scroll saw

blades generally stay sharp for 112hour to 2

hours of cutting, depending on type of material

and speed of operation.

•To get accurate cuts, be prepared to compen-

sate for the blade's tendency to follow the wood

grain as you are cuttingwood.

•In cutting wood, best results are achieved when

cuttingwood less than one inch thick.

•When cuttingwood thicker than one inch, the

user must guide the workpiece very slowly into

the blade and take extra care not to bend or twist

the blade while cutting.

•When choosing a blade to use with your scroll

sew, consider the following carefully:

•Very fine, narrow blades should be used to

scroll cut in thin matedal 1/4 in. thick or less.

Most blade packages state the size or thick-

ness and type of material which that blade is

intended to cut. Package should also state the

radius, or size of curve, which can be cut with

that blade.

•Wider blades cannot cut curves as tight or

small as thinner blades.

•Blades wear faster:

•When cutting plywood and other laminates.

•When cutting matedal thicker than 3/4 in.

•When cutting hardwood.

•When side pressure is applied to the blade.

ON/OFF KNOB WITH VARIABLE SPEED

See Figure 16.

Your scroll saw has an easy access On/Off knob with

variable speed.

•Pull the knob outto turn ON the saw, and push

the knob in to turn OFF the sew.

Note: After saw is turned on, a hesitation before

blade movement is normal.

WARNING: Never leave the saw unattended

untilthe blade has come to a complete stop to

prevent seriouspersonal injury.

POST

ON/OFFKNOB Fig. 16

•By turning the knob, the variable speed control

may be adjusted from the highspeed of approxi-

mately 1700 SPM (Strokes Per Minute) to the

low speed of approximately 500 SPM. Suggested

speeds are identified under Choice of Blade and

Speed, page 18. Turn the On/Off knob to the

rightor clockwise to increase strokes per minute

and to the left or counterclockwiseto reduce the

strokes per minute.

This motor has an electronic control that regulates the

speed and provides ovedoad protectionto the motor.

If the motor fails to start after about 2 seconds, push

the knob OFF and disconnect the saw from the power

source. Refer to the troubleshooting chart.

Note: I1the internal overload protector has been

tripped, pushing the On/Off knob OFF will reset it.

LOCK POST

See Figure 17.

To prevent unauthorized use of your scroll saw, we

suggest that you disconnect it from the power supply

and lockthe knob in the OFF position. A padlock with

ashackle of 5 mm or 3/16 in. diameter should be

used. When the lock is installed and locked, as

illustrated, the switchis inoperable. Store the padlock

key in another location.

•To lock the saw in the OFF position, installa

padlock through the lock post beside the knob as

illustrated and lockthe padlock. (Padlock is not

supplied with the saw.)

,_ WARNING: For your own safety, always push

the knob OFF when machine is not in use. Also,

in the event of apower failure, push knob OFF.

Lock the scroll saw switch OFF with a padlock.

This will prevent the machine from starting up

again when the power comes back on. Failure to

heed this warning can result in serious personal

injury.

INTERIOR SCROLL CUTTING

See Figure 18.

•One of the features of ascroll saw is that it can

be used to make scroll cuts on the interiorof a

board without breaking or cuttingthrough the

edge or perimeter of the board.

&WARNING: To avoid possible serious injury

from accidental starting, always turn the switch

OFF and remove plugfrom power source outlet

before removing or replacing the blade.

•To make interiorcuts in aboard, remove the

scroll saw blade as explained in the Installing

Blades section on page 14.

•Drill a114in. hole in the board to be used to

make interiorcuts.

•Place the board on the saw table withthe hole in

the board over the access hole in the table.

•Installblade through hole in board then adjust

the holddown foot and the blade tension. See

pages 14 and 15.

•When finished making the interiorscrollcuts,

simply remove the blade from the blade holders

as described in the Installing Blades section,

and remove the board from the table.

DRILLHOLE

INTERIOR

PADLOCK ON/OFFKNOB

Fig. 17

Fig. 18

STACK CUTTING

See Figure 19.

After becoming well acquainted with your saw through

practice and experience, you may wish to try stack

cutting. Stack cutting may be used when several

identical shapes need to be cut. Several pieces of

wood may be stacked on top and secured to each

other before cutting. The wood pieces may be joined

together by placing double sided tape between each

piece or by wrapping masking tape around the

comers or ends of the stacked wood. You must attach

the stacked pieces of wood to each other so they will

move on the table as a single piece of material.

_k WARNING: To avoid possible, serious personal

injury,do not cut more than one loose piece of

material at a time.

Fig. 19

CHOICE OF BLADE AND SPEED

The scroll saw accepts a wide variety of blade widths and thicknesses for cutting wood and other fibrous materi-

als. Your saw uses 5 inch long blades of either the pin end or the plain end style. The blade width and thickness

and the number of teeth per inch to use are determined by the type of material and the size of the radius being

cut. A full selection of scrollsaw blades ere available through Sears Retail Stores.

Note: As a general rule, always select narrow blades for intricatecurve cutting, and wide blades for straightand

large curve cutting.

Teeth/Inch

Width

.110 in.

.095 in.

Thickness

.020 in.

.010 in.

Speed or

Strokes Per Material Cut

Minute

1200-1700

600-1200

500-600

Popular size for cutting hard and soft

woods 3116 in. up to 2 in. Plastics, paper,

felt, bone, etc,

Wood, plastics, extremely thin cuts on

materials 3/32 in. to 1/2 in. thick.

For tight radius work in thin materials

3/32 in. to 1/8 in. wood, veneer, bone,

fiber, ivory, plastic, etc.

BEFORE EACH USE:

•INSPECT YOUR SAW. Disconnect the saw. To

avoid injury from accidental starting, turn the

switch OFF and unplugthe saw before changing

the setup or removing covers, guards, or blade.

•INSPECT YOUR WORKPIECE. Make sure there

are no nails or foreign objects in the workpiece to

be cut.

•USE EXTRA CAUTION WITH LARGE, VERY

SMALL, OR AWKWARD WORKPIECES.

• Never use this tool to cut pieces too small to hold

by hand.

• Always use extra supports (tables, saw horses,

blocks, etc.) for any workpiece large enough to

tip when not held down to the table top.

•Never use another person as a substitutefor a

table extension, or as additional support for a

workpiece or to help feed, support, or pullthe

workpiece.

•When cuttingan irregularlyshaped workpiece,

plan your work so it will not pinchthe blade. A

piece of molding, for example, must lay flat or be

held by a fixture orjig that will not let it twist,

rock, or slip while being cut.

Properlysupportroundmaterialsuchasdowel

rods.Theyhaveatendencytorollduringa cut,

causingthebladeto"bite." To avoid this, always

use a "v" block.

• Clear everything except the workpiece and

related support devices off the table before

plugginginto power and turningthe saw on.

BPLAN THE WAY YOU WILL HOLD THE

WORKPIECE FROM START TO FINISH. Do not

hand hold pieces so small that your fingers will

go under the work hold-down.

•BEFORE FREEING ANY JAMMED MATERIAL:

•Turn switch OFF.

•Wait for all moving parts to stop.

•Unplug the saw.

WHEN BACKING OUT OF THE WORKPIECE,

THE BLADE MAY BIND IN THE KERF (CUT).

THIS IS USUALLY CAUSED BY SAWDUST

CLOGGING UP THE KERF. IF THIS HAPPENS:

•Turn switch OFF,

• Wait for all moving parts to stop.

•Unplug the saw.

•Remove the blade from the blade holders.

•Remove the workpiece with blade from the table.

•Remove blade from workpiece.

&WARNING: Before removing loose pieces from

the table, turn saw off and wait for all moving

parts to stop to avoid serious personal injury.

_. WARNING: When servicing, use only identic&l

Craftsman replacement parts. Use of any other

part may create ahazard or cause product

damage.

WARNING: To prevent accidental starting that

could cause possible serious personal injury,

turn off and unplug the saw before maintaining or

lubricatingyour scroll saw.

GENERAL MAINTENANCE

Keep your Scroll Saw clean.

After cleaning the table top initially,apply a thin

coat of automobile type (paste) wax to the table

top so the wood slides easily while cutting.

ARM BEARINGS

See Figure 20.

Lubricate the arm bearings after every 50 hours of

use or whenever there is a squeak coming from the

bearings.

•Carefully place the saw on its side as shown in

Figure 20. Remove the rubber cap from the

lower arm of the saw.

•Squirt a few drops of SAE20 oil around the shaft

end and bronze bearing. Let oil soak in over-

night, remaining in this position.

Note: Lubricate the upper arm bearing from the other

side of the saw.

_k, WARNING: If the power cord is worn, cut, or

damaged in any way, have it replaced

immediately by a qualified service technician at a

Sears store to avoid riskof personal injury.

BRONZEBEARING

MOTOR BRUSHES

See Figure 21.

Your saw has externally accessible brush assemblies

that should be checked periodicallyfor wear. When

one of the two brushes becomes worn, replace both

brushes.

•Unplug your saw.

_, WARNING: Failure to unplugyour saw could

result in accidental starting causing serious

injury.

•Remove brush cap with a flat blade screwdriver.

•Remove brush assembly. Gently pry the brush

assembly out using a small screwdriver, point of

anail or paperclip, etc.

•Check for wear. If one brush is worn down

shorter than 114in., replace both brushes. Do

not replace one side without replacing the other.

•Reassemble using new brush assembly. Make

sure curvature of brush matches curvature of

motor and that brush moves freely in brushtube.

Use the blunt end of something thin (eraser end

of pencil, etc.) to push the brush into the tube

until it stays.

•Make sure brushcap is oriented correctly

(straight) and replace.

•Tighten brush cap usinga hand powered screw-

ddver only. Do not overtighten.

•Repeat for other brush.

_j_1. BRUSHCAP

Fig. 21

,_ WARNING: For your own safety, turn switch OFF and remove plug from power outlet before adjusting or

aligning your scrollsaw.

PROBLEM CAUSE SOLUTION

Motor will not run. 1. Problemwith ON-OFF switch, I.

power cord, or outlet.

2. Motor Defective. 2,

Have worn parts replaced before using

Scroll Sew again. Have the proper

outlet installed by aqualified electri-

cian.

Do notattempt any repair. Have

repaired by a qualified service techni-

cian at a Sears store or repair center.

Blades breaking.

Vibration (there is always

some vibration when the saw

is running).

1. Too much tension. 1. Adjust tension.

2, Feeding too quickly. 2. Reduce feed rate.

3, Wrong blade. 3.

4. Blade twistingin wood. 4.

Narrow blades for cuttingthin wood or

tight corners and turns, wide blades for

thicker wood or wide turns,

Reduce side pressure on blade, check

blade tension.

1. Improper mounting of saw.

2. Mounting surface.

3. Loose table or table resting

against motor.

4. Loose motor mounting. 4. Tighten mounting screws.

Blade runout (blade not 1. Blade holders out of line. 1.Realign blade.

properly aligned with arm

motion).

1. Check mounting.

2. Check mounting in manual.

3. Tighten table lock knob.

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

_-35

/-/

/*°

./'/" 15

/'/25 24 23 52

26 18

28 29

33 32 22 21

17 16 15

FIGURE A

Key

No.

Pert

Number

979817-001

980119-001

979814-001

979813-001

979832-001

979810-001

979809-001

979807-001

979806-001

979729-001

979730-001

979808-001

979805-001

979804-001

979803-001

979802-001

980123-001

979788-001

979786-001

979785-001

979784-001

979775-001

979776-001

979774-001

979773-001

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

PARTS LIST FOR FIGURE A

Description Ouan.

Blade Lock Knob........................................... 1

Blade Holder ................................................. 1

Spring Pin ..................................................... 1

Saw Blade ..................................................... 1

Throat Plate .................................................. 1

Table ............................................................. 1

Table Screw .................................................. 1

Blade Drawer ................................................ 1

Blade Drawer Bracket................................... 1

Washer ......................................................... 3

Screw (Pan Hd.) ........................................... 3

Screw (Pan Hd.) ........................................... 2

Bevel Lock Knob........................................... 1

Flat Washer .................................................. 2

Scale ............................................................. 1

Miter Scale Bracket ...................................... 1

Motor (Includes Kay Nos. 19, 20, 21, & 22). 1

Clamp Screw ................................................ 2

Brush Holder ................................................. 2

Brush Assembly ............................................ 2

Brush Cap ..................................................... 2

Counterbalance ............................................ 1

Clamp Screw ................................................ 1

Spacer .......................................................... 1

Screw (Pan Hd.) ........................................... 1

Key Part

No. Number

27 979772-001

28 979820-001

29 979821-001

30 979822-001

31 979823-001

32 979824-001

33 979825-001

34 979771-001

35 979769-001

36 979768-001

37 979770-001

38 979766-001

39 979767-001

40 979801-001

41 979800-001

42 979799-001

43 979798-001

44 979797-001

45 979796-001

46 979794-001

47 979793-001

48 979795-001

49 979790-001

50 979791-001

51 979789-001

52 979777-001

Description Quan.

Indicator........................................................ 1

Hex Bolt ........................................................ 1

Hex Nut ......................................................... 1

Hex Bolt (Socket Hd. Special) ...................... 1

Washer ......................................................... 1

Stopper ......................................................... 1

Spring Pin ..................................................... 1

Base .............................................................. 1

Hex Bolt ........................................................ 4

Waming Label ............................................... 1

Hex Bolt ........................................................ 3

Screw (Pan Hd.) ........................................... 2

Nozzle ........................................................... 1

Screw (Pan Hd.) ........................................... 2

Control Box ................................................... t

PC Board Assembly ..................................... t

Gasket .......................................................... 1

On/Off Knob .................................................. 1

Knob Label .................................................... 1

Motor Pointer ................................................ t

Switch Label ................................................. t

Motor Cover .................................................. 1

Power Cord Assembly .................................. 1"

Strain Relief .................................................. 1

Screw (Pan Hd.) ........................................... 4

Motor Screw .................................................. 3

*** Available at your nearest Sears Retail Store.

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

j:.

29 30

39 40

FIGURE B

Key

No.

CRAFTSMAN SCROLL SAW - MODEL NO. 315.216260

The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your SCROLL |

SAW or when ordering repair parts. I

Pad

Number

979827-001

979737-001

979736-001

979742-001

979735-001

979766-001

979734-001

979828-001

979733-001

979830-001

979732-001

979765-001

979763-001

979764-001

979814-001

979813-001

980119-001

979817-001

979762-001

979731-001

979761-001

979760-001

979769-001

PARTS LIST FOR FIGURE A

Description Quart.

Tension AdjustingKnob........................... ,... 1

Spring Pin ..................................................... 1

Quick Release Knob ..................................... 1

Rubber Boot.................................................. 1

Cam .............................................................. 1

Arm Spdng .................................................... 1

Tension Wedge ............................................. 1

Washer ......................................................... 1

Tension Bolt .................................................. 1

E-Ring ........................................................... 1

Tension Wedge ............................................. 1

Bushing......................................................... 4

Lower Arm .................................................... 1

Spacer Bearing ............................................. 2

Spring Pin ..................................................... 1

Blade Holder ................................................. 1

Blade Lock Knob ........................................... 1

Link ............................................................... 1

Spdng Washer .............................................. 2

Screw (Socket Hd. Cap) ............................... 1

Washer ......................................................... 2

Screw (Pan Hd.) ........................................... 2

Key Pad

No. Number

24 979758-001

25 979826-001

26 979752-001

27 979751-001

28 979740-001

29 979738-001

30 979741-001

31 979831-001

32 979744-001

33 979745-001

34 979749-001

35 979743-001

36 979747-001

37 979746-001

38 979748-001

39 979753-001

40 979754-001

41 979755-001

42 979757-001

43 979829-001

972000-549

Description Quen.

Ball Beadng .................................................. 2

Bolt (Hex Hd.) ............................................... 1

Right Arm Cover ........................................... 1

Spring Pin ..................................................... 1

Screw (Pan Hd.) ........................................... 8

Data Plate ..................................................... 1

Hold Down Foot Lock Knob.......................... 1

Support Bar Assembly .................................. 1

Foot AdjustingKnob ..................................... 1

Support Plate ................................................ 1

Hold Down Clamp ......................................... 1

Washer/Spacer ............................................. 1

Hold Down Foot ............................................ 1

Air Hose ........................................................ 1

Air Diaphragm............................................... 1

Upper Arm .................................................... 1

Hand Warning Label ..................................... 1

Left Arm Cover .............................................. 1

Logo Plate ..................................................... 1

Rubber Stopper ............................................ 3

Owners Manual

* Standard Hardware Item -- May Be Purchased Locally ** Available From Division 98 - Source 980.00

For in-home major brand repair service:

Call 24 hours a day, 7 days a week

1-800-4-MY-Home TM (1-800-469-4663)

Para pedir servicio de reparacibn a domicilio - 1-800-676-5811

In Canada for all your service and parts needs call - 1-800-665-4455

Au Canada pour tout le service ou les pi_ces

For the repair or replacement parts you need:

Call 7 am - 7 pm, 7 days a week

1-800-366-PART (1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1-800-659-7084

For the location of a Sears Parts and Repair Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

For information on purchasing a Sears Maintenance Agreement

or to inquire about an existing Agreement:

Call 9 am - 5 pm, Monday - Saturday

1-800-827-6655

The Service Side of Sears s"

Craftsman 315216260 User Manual 16IN. VARIABLE SPEED SCROLL SAW Manuals And Guides L9050206

CRAFTSMAN Saw Scroll Manual L9050206 CRAFTSMAN Saw Scroll Owner's Manual, CRAFTSMAN Saw Scroll installation guides

ROLLCAGE B5115-0920 L9050206

Navigation menu

Versions of this User Manual:

Views

Navigation