Craftsman 315265030 User Manual ROUTER TABLE Manuals And Guides L0408626
CRAFTSMAN Router Accessory Manual L0408626 CRAFTSMAN Router Accessory Owner's Manual, CRAFTSMAN Router Accessory installation guides
User Manual: Craftsman 315265030 315265030 CRAFTSMAN ROUTER TABLE - Manuals and Guides View the owners manual for your CRAFTSMAN ROUTER TABLE #315265030. Home:Tool Parts:Craftsman Parts:Craftsman ROUTER TABLE Manual
Open the PDF directly: View PDF 
.
Page Count: 22
| Download | |
| Open PDF In Browser | View PDF |
Operator's Manual II:RRFTSMRN I ROUTER TABLE Double Insulated Model No. 315.265030 _h WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: t-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.com/craftsman 983000-479 7-04 Save this manual Estates, IL 60179 USA for future reference • Warranty ........................................................................................................................................................................... 2 • Introduction ...................................................................................................................................................................... 2 • General Safety Rules ........................................................................................................................................................ 3 • Specific Safety Rules ........................................................................................................................................................ 4 • Symbols ........................................................................................................................................................................ • Electrical ........................................................................................................................................................................... • Features ........................................................................................................................................................................ • Assembly .................................................................................................................................................................. 10-13 • Operation .................................................................................................................................................................. 14-17 • Maintenance ................................................................................................................................................................... • Exploded View and Parts List ................................................................................................................................... • Parts Ordering/Service ................................................................................................................................................... FULL ONE YEAR WARRANTY 5-6 7 8-9 18 20-21 22 ON CRAFTSMAN TOOL If this CRAFTSMAN tool fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears will repair it, free of charge. If this CRAFTSMAN of purchase. tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability been given top priority in the design of this product making it easy to maintain and operate. have _k ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impactresistant lenses; they are NOT safety glasses. WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and it frees both hands to operate tool. READ ALL INSTRUCTIONS • KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the applications and limitations as well as specific potential hazards related to this tool. • GUARD AGAINST ELECTRICAL SHOCK by preventing body contact with grounded surfaces. For example: pipes, radiators, ranges, refrigerator enclosures. • KEEP GUARDS IN PLACE and in working order. Never operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use. • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see keys and adjusting wrenches are removed from tool before turning it on. • KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents. • DON'T USE IN DANGEROUS ENVIRONMENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations or expose them to rain. Keep work area well lighted. • DO NOT OVERREACH. balance at all times. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. • DISCONNECT ALL TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power source. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Be sure switch is off when plugging in. • USE RECOMMENDED ACCESSORIES, Consult the operator's manual for recommended accessories. The use of improper accessories may cause risk of injury. • NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the blade is unintentionally contacted. • CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury. • DIRECTION OF FEED. Feed work into a blade or cutter against the direction or rotation of the blade or cutter only. • NEVER LEAVE TOOL RUNNING UNATTENDED, TURN POWER OFF. Don't leave tool until it comes to a complete stop. KEEP CHILDREN AND VISITORS AWAY. All visitors should wear safety glasses and be kept a safe distance from work area. • MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing starter keys. • DON'T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. • USE THE RIGHT TOOL. Do not force the tool or attachment to do a job for which it was not designed. • USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. • WEAR PROPER APPAREL. Do not wear loose clothing, neckties, or jewelry that can get caught in the tool's moving parts and cause personal injury. Nonslip footwear is recommended when working outdoors. Wear protective hair covering to contain long hair. Keep proper footing and • DON'TABUSECORD.Nevercarrytool bythecordor yankitto disconnect fromreceptacle.Keepcordfrom heat,oil,andsharpedges. • PROTECT YOURLUNGS.Wearafaceordustmaskif the cuttingoperationisdusty. • PROTECT YOURHEARING. Wearhearingprotection duringextendedperiodsofoperation. • KEEPTOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. • INSPECT TOOL CORDS AND EXTENSION CORDS PERIODICALLY and, if damaged, have repaired by a qualified service technician. Stay constantly aware of cord location and keep it well away from the rotating wheel. • NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. • USE ONLY OUTDOOR EXTENSION CORDS with approved ground connection that are intended for use outdoors and so marked. _ • KEEP HANDS AWAY FROM CUTTING AREA. Do not reach underneath the table or in the cutting path with your hands or fingers at any time while the tool is connected to a power source. • DO NOT use awkward hand positions. • USE OVERHEAD GUARD WHEN ADJUSTABLE FENCE IS NOT IN PLACE. • FIRMLY CLAMP OR BOLT THE ROUTER TABLE TO A WORK SURFACE so that the router table surface is approximately hip height. • INSPECT FOR AND REMOVE ALL NAILS FROM LUMBER BEFORE ROUTING. Following this rule will reduce the risk of serious personal injury. • DRUGS, ALCOHOL, MEDICATION. DO NOT OPERATE TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION. Following this rule will reduce the risk of electric shock, fire, or serious personal injury. • SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. WARNING" Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Someof the followingsymbolsmaybeusedonthis tool. Pleasestudythemandlearntheirmeaning.Proper interpretation ofthesesymbolswillallowyouto operatethetool betterandsafer. SYMBOL NAME DESIG NATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic no No Load Speed Rotational speed, at no load [] Class II Construction Double-insulated Per Minute Revolutions, strokes, surface speed, orbits etc., per minute Wet Conditions Alert Do not expose to rain or use in damp locations. Read The Operator's Manual operator's manual before To reduce the risk of injury,using user this mustproduct. read and understand min "_ .../min O _, @ @ @ ® Eye Protection of current construction Always and wearasafety goggles safety glasses this withproduct. side shields full face shield or when operating Safety Alert Precautions that involve your safety. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. Hot Surface To reduce the risk of injury or damage, avoid contact with any hot surface. Thefollowingsignalwordsandmeanings areintendedto explainthe levelsofriskassociatedwiththisproduct. SYMBOL SIGNAL MEANING ,_ DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. _k WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. ,_ CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. CAUTION: (Without Safety Alert Symbol) Indicates a situation property damage. SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts. ,_ A that may result in WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing others who may use this product. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. SAVE THESE INSTRUCTIONS DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. ,_ WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal insulation. Observe all normal safety precautions to avoid electrical shock. NOTE: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELECTRICAL CONNECTION This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check the power supply. EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used. When working outdoors with a tool, use an extension cord that is designed for outside use. This type of cord is designated with "WA" on the cord's jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation. **Ampere rating (on tool faceplate) 0-2.0 2,1-3.4 Cord Length 3.5-5.0 5.1-7.0 7.1-12.0 12,1-16.0 Wire Size (A,W.G.) 25' 16 16 16 16 14 14 50' 16 16 16 14 14 12 100' 16 16 14 12 10 -- **Used on 12 ga_e - 20 amp c_uit. NOTE: AWG = American Wire Gauge A WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury. A WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. PRODUCT SPECIFICATIONS Miter Slot ........................................ Table Dimensions ............ 14 in. x 24 in. (35.6 cm x 61 cm) Maximum Cutter Diameter .................. 1-15/16 in. (4.9 cm) Fence Width ........................................ 3/8 in x 3/4 in. x 24 in. (0.9 cm x 1.9 cm x 61 cm) 16-3/8 in. (41.6 cm) Input ................................................ 120 V, 60 Hz, AC only Net Weight .................................................. 20 Ibs. (9.1 kg) CUTTERGUARD ASSEMBLY FENCEASSEMBLY MITER GAUGE SWITCH KEY SWITCH FRONTVIEW REARVIEW Fig. 1 KNOW YOUR ROUTER TABLE See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. CUTTER GUARD ASSEMBLY The cutter guard assembly provides a barrier to protect the operator from contact with the cutter and is adjustable for all types of cuts and materials. The cutter guard also doubles as a vacuum attachment. You can insert a standard shop vacuum into the top of the clear plastic cutter guard to keep dust to a minimum. FENCE ASSEMBLY The fence assembly provides an adjustable surface to support and guide the work. MITER GAUGE A miter gauge is used for mitered routing and to help support wider pieces. STARTING PIN When you are unable to use the fence for a guide because the workpiece is odd-shaped or too small, use the starting pin for a guide. Only use piloted cutters when using the starting pin. Remove the fence and miter gauge when using the starting pin. SWITCH This product is equipped with a power switch that has a built-in locking feature. This feature is intended to prevent unauthorized and possible hazardous use by children and others. If you remove the key during operation, you can turn the switch off, but you may not turn it on again until you replace the key. THROAT PLATES Five throat plates are included with the router table. The throat plate provides a stable support surface around the cutter and prevents objects from falling through the throat and damaging the spindle. UNDERTABLE AND REAR SAFETY GUARDS The undertable guard and rear safety guard ensure that your hand, loose clothing, and other objects do not come in contact with the cutter or collet during operation. _k WARNING: The undertable and rear safety guards must be securely in place before using the router table. Failure to do so could result in serious personal injury. UNPACKING PACKING This product requires assembly. 1. Router table top (1) 2. Miter gauge knob (1) 3. Washer (1) 4. Miter gauge (1) 5. Hex key (1) 6. Bar (1) 7. Switch box assembly (1) 8. Guard post (1) 9. Cutter guard assembly (1) 10. Undertable guard (1) 11. Carriage bolt (2) 12. Socket head screw (16) 13. Lock washer (19) 14. Flat head machine screw (3) 15. Small screw (2) 16. Starting pin 17. Pan head machine screw (2) 18. Fence assembly (1) 19. Fence lock knob (2) 20. Throat plate (5 21. Table leg (4) 22. Rear safety guard (1) 23. Socket head screw (3) Operator's Manual (not shown) • Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. • If any parts are damaged or missing, please call 1-800-932-3188 for assistance. _i WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. A WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. LIST 1 21 2O 18 3 18 10 22 23 _ 11 o r-'15 13 5 12 Fig. 2 10 ,_ WARNING:Donotconnectto powersupplyuntil assemblyis complete.Failureto complycouldresult inaccidentalstartingandpossibleseriousinjury. ASSEMBLING THE ROUTER SWITCH ASSEMBLY TABLE SWITCH When you remove the parts and hardware from the packing materials, check all items with the packing list and drawing. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s). TO ATTACH CUTOUT THE LEGS See Figure 3. • Place router table top upside down on a flat, level surface with the front edge closest to you. • Place each leg in a corner of the table. NOTE: The leg with the switch cut-out should be placed in the front left corner of the table. The leg with the warning label should be placed in the front right corner of the table. • Align the holes in the legs with the threaded holes in the table. • Use the hex key provided, secure each leg with the socket head screws and lock washers. Fig. 4 TO ATTACH THE UNDERTABLE See Figure 5. • Position the undertable guard around the throat of the table. • Align the three holes of the guard with the threaded holes in the table. • Use the hex key provided to secure the undertable guard with the socket head screws and lock washers. • Turn the router table upright and be sure the table is stable and rests securely on all four legs. LOCK WASHER SOCKET HEAD SCREWS UNDER TABLE GUARD '_ I Fig. 3 TO ATTACH THE SWITCH ASSEMBLY i See Figure 4. • Hold the switch assembly so that the words ON and OFF on the toggle switch are upside down. • Place the switch assembly against the cutout in the left front leg. • Align the small holes in the mounting tabs with the small holes in the leg. • Using a phillips screwdriver, secure the switch assembly to the leg with the small screws. GUARD & THROAT 11 Fig. 5 TO ATTACH THE FENCE See Figure 6. • Position the fence on the tame as shown in figure 6. • Align the ho(es on the bottom of the fence with the channe(s on the router tame. • Using the two carriage bolts and fence lock knobs, secure the fence to the tame. BLACK.CUTTER KNOB TO LOOSEN GUARD POST BLACK KNOB GUARD ,_1_T TO IGHTEN FENCE LOCK KNOBS FENCE Fig. 7 FENCE ASSEMBLING THE MITER GAUGE See Figure 8. • Position the miter gauge on the bar by placing the miter gauge under the indicator and over the post. NOTE: The miter gauge should rest securely on top of the bar. • i CARRIAGE BOLT • Fig. 6 TO ATTACH THE CUTTER ASSEMBLY Place the washer over the threaded hole then screw the miter gauge knob through the washer and into the hole. Tighten securely by turning the miter gauge knob clockwise GUARD GAUGE MITER KNOB See Figure 7. • Screw the guard post securely into one of the threaded holes on the top of the fence. I NOTE: When the fence is close to the cutter, place the guard post in the off-center threaded hole to provide protection from the cutter and allow for proper suction for the vacuum. • Loosen the plastic ring on the cutter guard by turning the black knob counterclockwise. • Slide the ring over the guard post. • Center the cutter guard over the throat of the router table. • Tighten the cutter guard by turning the black knob clockwise. MITER / GAUGE POST_BAR NOTE: To keep saw dust to a minimum, attach a standard shop vacuum to the top of the cutter guard. Fig. 8 12 ATTACHING THE REAR SAFETY GUARD THE ROUTER TO MOUNTING SURFACE THE TABLE TO A WORK See Figure 9. See Figures 11 and 12. • Align the holes in the rear safety guard with the holes in the router. • Place the router table right side up on a sturdy work surface (e.g., work stand, workbench, counter top). • Using two screws, secure the rear safety guard to the router. • Mark the surface with a pencil through the holes in the table legs. Remove the router table. • Drill four holes through the work surface. • Align the holes in the table legs with the holes in the work surface. Position the router table surface at approximately hip height. • Insert four bolts (not included, 1/4-20 recommended) and tighten securely with lock washers and hex nuts (not included). REAR SAFETY GUARD NOTE: If you plan to transport the router table to different locations, we recommend you attach it permanently to a mounting board that you can easily clamp to a work surface. Fig. 9 MOUNTING THE ROUTER TO THE TABLE See Figure 10. Mount the router to the router table after the router table has been completely assembled and the rear safety guard has been installed on the router. • Hold the router upside down so that the front of the router faces you. • Align the holes in the center of the table with the holes in the router. • Holding the router with one hand, securely tighten each of the three screws as shown in figure 10. I i e Fig. 11 FRONTOF ROUTER Fig. 10 Fig. 12 13 _ PERFORMING WARNING" Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious _ WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. Read the entire 175100 Router Operator's • Adjust the cutter guard so that it will not come in contact with the workpiece or cutter during a cutting operation. result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: • Adjust the infeed fence to support the uncut workpiece and adjust the outfeed fence to support the workpiece after the cut. • Piloted cutter operations using the starting pin for edging patterned surfaces on wood and wood composition materials USING THE ROUTER TABLE • Always plug the router into the router table switched outlet. Never plug a router table mounted router into another power source. Lock-on the router switch. Refer to the 175100 router manual for details, • Make sure the router table switch is off. Remove the switch key. • Plug the router table power cord into a power source. • Always control the power to the router with the router table switch whenever the router is mounted on the table. Feed the workpiece from right to left with the cutter located in the fence opening. WARNING: The direction of feed for the workpiece is always against the sharp edges of the cutter and therefore into the rotation of the cutter. Failure to WARNING: When operating the router with the router table, the router must only be plugged into and controlled by the router table switched outlet. To reduce the risk of serious personal injury, never connect the table mounted router into another power source. CUTTER GUARD Manual. • • A Observe the following rules when using the router with the router table. Read the entire 175100 Router Operator's Reconfirm that all router adjustments are securely locked before connecting the router table to a power source. feed the work into the cutter correctly can result in serious personal injury. WITH THE ROUTER • • A • Table mounted dado and mortise operations in wood and wood composition materials Fence guided edging operations for cabinetry and picture framing on wood and wood composition materials Manual. NOTE: The workpiece must always be tight against the fence, unless you are using a ball-bearing piloted cutter. Additionally, it may be necessary to remove the center fence plate if using large cutters up to 2 1/4 in. not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can _ • WARNING" Current and accessories available for use with attachments this tool are listed above. Do • OPERATION See Figure 13, injury. ,_ A ROUTING WORKPIECE INFEEDFENCE OUTFEED FENCE WARNING: When using a router table, larger router bits should be used for edging only. Do not use router bits that are larger in diameter than the opening in the router table. Fig. 13 14 INSERTING/REMOVING CUTTERS INSERTING THROAT PLATES See Figure 14. See Figure 15. • The throat plate provides a stable surface around the cutter and prevents objects from falling through the throat and damaging the spindle. _ Unplug the router and the router table. WARNING: To prevent damage to the spindle or spindle lock, always allow the motor to come to a complete stop before engaging the spindle lock. • Remove the screws from the rear safety guard. • Remove the rear safety guard from the router. • Follow the directions for installing and removing cutters in the 175100 router. ,_k WARNING: Use this router table only with the 175100 router. Do not attempt to use any other router with this table. Failure to heed this warning could result in improper operation of the tool and serious personal injury. • Return the rear safety guard to its proper position. • Secure the rear safety guard by inserting and tightening the two screws previously removed. _k The proper size throat plate depends on the size and shape of the cutter. When inserted, the throat plate opening should be within approximately 1/4 in. (6.4 mm) of the outermost edge of the cutter. • Position the throat plate over the throat opening in the router table. • Align the tab in the throat plate with the slot in the throat opening. • Snap throat plate down and into place as shown. NOTE: To remove throat plate, pull gently until the throat plate snaps out. THROAT PLME WARNING: If you are changing a cutter immediately after use, be careful not to touch the cutter or collet with your hands or fingers. They will get burned because of the heat buildup from cutting. Always use the wrench provided. CUTTER WRENCH COLLETNUT TO LOOSEN COLLETNUT SLOT Fig. 15 TOTIGHTEN COLLETNUT DEPRESS SPINDLELOCK Fig. 14 15 ADJUSTING DEPTH OF CUT POSITIONING THE FENCE See Figure 16. See Figure 17. We recommend that cuts be made at a depth not exceeding 1/8 in. (3.2 mm) and that several passes be made to reach depths of cut greater than 1/8 in. (3.2 mm). The fence enables you to support and guide the workpiece. • Loosen the fence lock knobs. • • Position the fence the proper distance from the cutter based on the amount of material you plan to remove. • Tighten the fence lock knobs. Unplug the router and the router table. ,_ WARNING: Failure to unplug the router and router table could result in accidental starting causing serious injury. • Unlock the clamping lever. • Turn the depth adjusting ring until the tip of the cutter touches the work surface (zero depth of cut). • Turn depth indicator ring to zero depth of cut on the scale. • Turn the depth adjusting ring to the desired depth of cut. • Lock the clamping lever securely. FENCELOCK KNOBS FENCELOCK KNOBS NOTE: When you use certain cutters, you may need to remove the black plastic subbase from the router to achieve full depth of cut. Fig. 17 ADJUSTING THE STEP RISERS See Figure 18. The step risers, located on the outfeed side of the fence, enable you to support the workpiece as it exits the cutter. The step risers provide support for routing operations that remove up to 1/8 in. (3.2 mm) of material. The step risers are adjustable in 1/32 in. (0.8 mm) increments. • Loosen the knob bolts on the rear of the fence. • Push the riser forward and toward the throat. • Tighten the knob bolts. CLAMPING LEVER TO LOWER CUTTER \ i KNOB BOLTS / INDICATOR POINT Fig. 18 Fig. 16 16 ADJUSTING THE MITER GAUGE INSERTING THE STARTING PIN See Figure 19. See Figure 20. • Loosen the miter gauge knob. • Rotate the miter gauge to the desired angle. The purpose of the starting pin is to act as a guide with piloted bits. • Tighten the miter gauge knob. Place the starting pin on the router table and use it as a pivot point when cutting small, odd-shaped pieces. NOTE: Do not use the fence when you are using the starting pin. Additionally, only use piloted cutters when using the starting pin. MITER GAUGE KNOB • Place the starting pin into the threaded hole to the right of the router table throat opening. • Turn the pin clockwise to secure. ,_ WARNING: Using the fence when using the start pin can result in the work binding and kicking back resulting in serious personal injury. Do not use the fence or miter gauge when using the starter pin. STARTINGPIN TO LOOSEN MITER GAUGE Fig. 19 : TOTIGHTEN o Fig. 20 17 _k WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. _k WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. GENERAL Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air. MAINTENANCE LUBRICATION Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. _k Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. 18 19 CRAFTSMAN ROUTER TABLE - MODEL NUMBER 315.265030 • 22 21 2O 18 14 13 7 11 10 12 2O • CRAFTSMAN ROUTER TABLE- MODEL NUMBER 315.265030 • J The modelmodel number number in allwill correspondence be found on a regarding plate attached your ROUTER to the motor TABLE housing. or when Always ordering mention repair the parts. | SEE BACK KEY PART NO, NO, PAGE FOR PARTS ORDERING INSTRUCTIONS DESCRIPTION QTY, 1 690559001 Guard Post ........................................................... 1 2 590378001 Lock Knob ............................................................. 2 3 A310695005 Fence Assembly .................................................... 1 4 660141002 Carriage Bolt (M6 x 30 mm) .................................. 2 5 640736001 Router Table Top ................................................... 1 6 A310695003 Table Leg ............................................................... 3 7 660206025 Screw (M3.5 x 10 mm) .......................................... 2 8 303471-000 Switch Key ............................................................ 1 9 A310695006 Switch Assembly ................................................... 1 10 A310695004 Front Leg ............................................................... 1 11 680873003 Hex Key ................................................................. 1 12 660683001 Screw (6-32 x 3/8 in.) ............................................ 2 13 512575001 Rear Safety Guard ................................................. 1 14 590371001 Undertable Guard .................................................. 1 15 660686001 Socket Head Screw (M6 x 19 mm) ..................... 16 16 690558001 Lock Washer (M6) ............................................... 17 660169041 Socket Head Screw (M6 x 12 mm) ........................ 3 18 660684001 Flat Head Machine Screws (10-32 x 3/4 in.) ......... 3 19 620216001 Starting Pin ............................................................ 1 20 512574001 Throat Plate A, 2 in ................................................ 1 512574002 Throat Plate B, 1-1/2 in ......................................... 1 512574003 Throat Plate C, 1-1/4 in ......................................... 1 512574004 Throat Plate D, 1 in ................................................ 1 512574005 Throat Plate E, 1/2 in ............................................. 1 21 A310695008 Miter Gauge Assembly .......................................... 1 22 A310695007 Cutter Guard Assembly ......................................... 1 983000-479 Operator's Manual 21 19 Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! .................. For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. .................. For Sears professional installation of home appliances and items like garage door openers and water heaters. .................. 1-8 00-4-MY-H 0 ME® (1-800-469-4663) oa,, an t, o, o,oht sod Oaoada www.sears.com .......... www.sears.ca Our Home For repair of carry-in items like vacuums, lawn equipment, and electronics, call or go on-line for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Call anytime, day or night (U.S.A. only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced 1-800-827-6655 Pard pedir servicio (U.S.A.) 1-800-361-6665 de reparacien Au Canada a domicilio, y para ordenar piezas. 1-8 8 8-S U- HO G AR sM by Sears: (Canada) pour service en frangais: 1 -800- LE- FO YER Mc (1-800-533-6937) (1-888-784-6427) www.sears.ca ............... .............. SEARS ® Registered Trademark / TMTrademark / SM Service Mark of Sears, Roebuck ® Marca Registrada / TM Marca de F_brica / SM Marca de Servicio de Sears, MC Marque de commerce / MD Marque d6pos6e de Sears, Roebuck and Co. and Co. Roebuck and Co. ® Sears, Roebuck and Co.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 22 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Apr 04 13:05:20 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools