Craftsman 32061325 User Manual SAW CIRCULAR Manuals And Guides 1007556L

User Manual: Craftsman 32061325 32061325 CRAFTSMAN SAW CIRCULAR - Manuals and Guides View the owners manual for your CRAFTSMAN SAW CIRCULAR #32061325. Home:Tool Parts:Craftsman Parts:Craftsman SAW CIRCULAR Manual

Open the PDF directly: View PDF PDF.
Page Count: 40

12.0-VOLT LiTHiUM-iON
CORDLESS 3-3/8 in. CIRCULAR SAW
Model No. 320.61325
_ owered by an
ENERGYSTAR®
qualified battery
__ charger for a
better environment
WARNING: To reduce the risk of
injury, the user must read and understand
the Operator's manual before using
this product.
* Warranty
* Safety
*Assernbly
* Operation
* Maintenance
Charge battery
before first use
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
www,crsftsrnan,corn
Warranty Page 2
Safety Symbols Page 3
Safety Instructions Pages 5-10
Glossary of Woodworking Terms Pages 10-11
Description Pages 12-13
Assembly Page 14
Operation Pages 14-30
Maintenance Pages 30-32
Troubleshooting Page 32
Exploded View and Parts List Page 33-36
Sears Repair Parts Phone Number Back Cover
CRAFTSMAN ONE YEAR FULL WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted
against any defects in material or workmanship. Defective product will be
replaced free of charge.
For warranty coverage details to obtain free replacement, visit the
web site: www.craftsman.com.
This warranty does not cover blades and bulbs, which are expendable
parts that can wear out from normal use within the warranty period.
This warranty is void if this product is ever used while providing
commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
SAVE THESE iNSTRUCTIONS!
READ ALL iNSTRUCTIONS
This cordless circular saw has many features for making its use more pleasant
and enjoyable. Safety, performance, and dependability have been given top
priority in the design of this product making it easy to maintain and operate.
WARNING: Some dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other
reproductive harm.
61325 Manual_Revised_lO 0225 Page 2
The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding. The symbol warnings do not by themselves
eliminate any danger. The instructions and warning they give are no substitutes
for proper accident-prevention measures.
WARNING: Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols such as "DANGER," "WARNING,"
and "CAUTION" before using this saw. Failure to following all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SYMBOL SIGNAL MEANING
,_ SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.
May be used in conjunction with other symbols or pictographs.
DANGER: Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
A_, CAUTION: Indicates an imminently hazardous situation, which, if not
avoided, may result in death or serious injury.
NOTE: These inform the user of import information and/or instructions that
could lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTE," as in the example below:
NOTE: Equipment and/or property damage may result if these instructions are
not followed.
WARNING: To ensure safety and reliability, all repairs should be performed
by a qualified service technician at Sears Service Center.
,_ WARNING: The operation of any power tools can result in
foreign objects being thrown into your eyes, which can result in
severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shield
and a full face shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields. Always use eye protection which is
marked to comply with ANSI Z87.1
SAVE THESE INSTRUCTIONS
6t325 Manual_Revised_lO 0225 Page 3
Some of these following symbols may be used on this tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to
operate the tool better and safer.
SYMBOL NAME DESIG NATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
"_ Alternating Current Type of current
Direct Current Type or a characteristic of current
n o No Load Speed Rotational speed, at no load
] Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed,
orbits, etc., per minute
Do not expose to rain or use in damp
Wet Conditions Alert locations.
i_ To reduce the risk of injury, user must
Read The Operator's Manual read and understand operator's manual
before using this product.
O Always wear safety goggles or safety
Eye Protection glasses with side shields and a full face
shield when operating this product.
Alert Precautions that involve
Safety your safety.
No Hands Symbol Failure to keep your hands away from theblade will result in serious personal injury.
No Hands Failure to keep your hands away from the
Symbol blade will result in serious personal injury.
No Hands Failure to keep your hands away from the
Symbol blade will result in serious personal injury.
No Hands Symbol Failure to keep your hands away from the
blade will result in serious personal injury.
Hot Surface To reduce the risk of injury or damage,avoid contact with any hot surface.
63_325 Manual_Revised_lO 0225 Page 4
GENERAL SAFETY RULES
AWARNING: Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
= Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
= Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
=Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
= Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
= Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
= Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
= When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
=if operating apower tool in adamp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
• Use the battery only with the charger listed:
BATTERY PACK CHARGER
320.11221 320.10006
61325 Manual_Revised_lO 0225 Page 5
PERSONAL SAFETY
=Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
= Use personal protective equipment. Always wear eye protection. Protective
equipment, such as dust mask, non-skid safety shoes, hard hat, or hearing
protection, used for appropriate conditions will reduce personal injuries.
=Prevent unintentional starting. Ensure that the switch is in the OFF
position before connecting to power source and/or battery pack, picking
up, or carrying the tool. Carrying power tools with your finger on the switch
or energizing in power tools that have the switch on invites accidents.
= Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
= If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of these devices can reduce dust-related hazards.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely at
the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack
from the power tool before marking any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
=Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation, if damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
= Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
61325 Manual_Revised_10 0225 Page 6
Use the power tool, accessories and, tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
•Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects,
such as paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery;
avoid contact, if contact accidentally occurs, flush with water, if liquid
contacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
•Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
• When servicing a power tool, use only identical replacement parts.
• Follow instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance instructions may create a
risk of shock or injury.
SPECiFiC SAFETY RULES FOR CIRCULAR SAW
_, DANGER: Keep hands and body away from and to the side of the blade.
Contact with blade will result in serious injury.
WARNING: To reduce the risk of injury, check guarding system. It must
cover the blade instantly! Hold the saw with both hands. Support and clamp
work. Wear eye protection.
DANGER: Keep hands away from cutting area and the blade. Keep your
second hand on the auxiliary handle or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
61325 Manual_Revised_lO 0225 Page 7
• Do not reach underneath the workpiece. The guard cannot protect you
from the blade below the workpiece.
• Adjust the cutting depth to the thickness of the workpiece. Less than a
full tooth of the blade should be visible below the workpiece.
• Never hold the piece being cut in your hands or across your leg. Secure
the workpiece to a stable platform, it is important to support the work
properly to minimize body exposure, blade binding or loss of control.
= Hold the power tool by its insulated gripping surfaces when performing
an operation where the cutting tool may contact hidden wiring or its
own cord. Contact with a "live" wire will also make exposed metal parts of
the tool "live" and shock the operator.
= When ripping, always use a rip fence or straight edge guide (sold
separately). This improves the accuracy of cut and reduces the chance of
blade binding.
= Always use blades with the correct size and shape of arbor holes.
Blades that do not match the mounting hardware of the saw will run
erratically, causing loss of control.
= Never use damaged or incorrect blade washers or bolt. The blade
washers and bolt were specially designed for your saw for optimum
performance and safety of operation.
CAUSES AND OPERATOR PREVENTION OF KICKBACK:
• Kickback is a sudden reaction to a pinched, bound or misaligned saw
blade, causing an uncontrolled saw to lift up and out of the workpiece
toward the operator.
When the blade is pinched or bound tightly by the kerf closing down, the blade
stalls and the motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back
edge of the blade can dig into the top surface of the wood causing the blade
to climb out of the kerf and jump back toward the operator. Kickback is the
result of misuse and/or incorrect operating procedures or conditions and can
be avoided by taking proper precautions, as given below:
Maintain a firm grip with both hands on the saw and position your arms
to resist kickback forces. Position your body to either side of the blade,
but not in line with the blade. Kickback could cause the saw to jump
backwards, but kickback forces can be controlled by the operator, if proper
precautions are taken.
• When blade is binding or when interrupting a cut for any reason, release
the trigger and hold the saw motionless in the material until the blade
comes to a complete stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is in motion or kickback
may occur. Investigate and take corrective actions to eliminate the cause of
blade binding.
61325 Manual_Revised_lO 0225 Page 8
When restarting a saw in the workpiece center the saw blade in the kerf
and check that saw teeth are not engaged into the material, if the saw
blade is binding, it may walk up or kickback from the work piece as the saw
is restarted.
•Support large panels to minimize the risk of blade pinching and
kickback. Large panels tend to sag under their own weight. Supports must
be placed under the panel on both sides, near the line of cut and near the
edge of the panel.
= Do not use dull or damaged blades. Unsharpened or improperly set blades
produce a narrow kerr, causing excessive friction, blade binding and kickback.
= Blade depth and bevel adjusting locking levers must be tight and secure
before making a cut. If the blade adjustment shifts while cutting, it may
cause binding and kickback.
= Use extra caution when making a "plunge cut" into existing walls or other
blind areas. The protruding blade may cut objects that can cause kickback.
• Check the lower guard for proper closing before each use. Do not
operate the saw if the lower guard does not move freely and close
instantly. Never clamp or tie the lower guard into the open position. If
the saw is accidentally dropped, the lower guard may be bent. Raise the
lower blade guard with the retracting handle. Make sure it moves freely and
does not touch the blade or any other part, in all angles and depths of cut.
• Check the operation of the lower guard spring, if the guard and the
spring are not operating properly, they must be serviced before use. The
lower guard may operate sluggishly due to damaged parts, gummy deposits
or a build-up of debris.
=Lower guard should be retracted manually only for special cuts such
as "plunge cuts" and "compound cuts." Raise the lower blade guard
with the retracting handle. As soon as the blade enters the material, the
lower guard must be released. For all other sawing, the lower guard should
operate automatically.
=Always observe that the lower guard is covering the blade before placing
the saw down on a bench or the floor. An unprotected, coasting blade will
cause the saw to walk backwards, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after the switch is released.
= When making a plunge cut with the bevel setting other than 90 °, ensure
that the guide plate of the saw will not shift. While performing the
"plunge cut" when the blade bevel setting is not at 90 °. Blade A blade
shifting sideways will cause binding and likely kick back.
= Use the appropriate riving knife for the blade being used. For the riving
knife to work, it must be thicker than the body of the blade, but thinner than
the tooth set of the blade.
61325 Manual_Revised_lO 0225 Page 9
=Adjust the riving knife as described in this instruction manual. Incorrect
spacing, positioning and alignment can make the riving knife ineffective in
preventing kickback.
= Always use the riving knife except when plunge cutting. The riving knife
must be replaced after plunge cutting. The riving knife causes interference
during plunge cutting and can create kickback.
= For the riving knife to work, it must be engaged in the workpiece. The
riving knife is ineffective in preventing kickback during short cuts.
= Do not operate the saw if riving the knife is bent. Even a slight
interference can slow the closing rate of a guard.
• Hold power tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own
cord. Contact with a "live" wire will also make exposed metal parts of the
tool "live" and shock the operator.
Spindle
The shaft on which a blade or cutting tool is mounted. Also called the Arbor.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one minute.
Saw Blade Path
The area over, under, behind or in front of the blade, as it applies to the
workpiece. That area which will be or has been cut by the blade.
Set
The distance that the saw blade tooth is bent (or set) outward from the face of
the blade.
Miter Cut
A cutting operation made with the blade at any angle other than 90o to the fence.
Compound Miter Cut A compound miter cut is a cut made using a miter angle
and a bevel angle at the same time.
Cross cut
A cutting or shaping operation made against the grain of the workpiece.
Bevel Cut
A cutting operation made with the blade at any angle other than 90o to the miter table.
Dado Cut
A non-through cut which produces a square-sided notch or trough in the
workpiece (requires special blade).
Chamfer Cut
A cut removing a wedge from a block of wood so the end (or part of the end) is
angled at other than 90 °.
61325 Manual_Revised_10 0225 Page 10
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Freehand Cut
Performing a cut without using a fence, miter gauge, fixture, work clamp, or
otherproper device to keep the workpiece from twisting or moving during the cut.
Through Sawing
Any cutting operation where the blade extends completely through the thickness
of the workpiece.
Non-Through Cuts
Any cutting operation where the blade does not extend completely through the
thickness of the workpiece, like a dado cut.
Leading End
The end of the workpiece pushed into tool first.
Kerr
The material removed by the blade in a through cut or the slot produced by the
blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls, throwing the workpiece
back toward operator.
Workpiece or Material
The item on which the cutting operation is being done. The surfaces of a
workpiece are commonly referred to as faces, ends and edges.
Gum
A sticky, sap-based residue from wood products.
Resin
A sticky, sap-based substance that has hardened.
61325 Manual_Revised_10 0225 Page 11
KNOW YOUR CIRCULAR SAW (Fig. 1)
Fig. 1
FuelGauge
Rear handle
Upper blade guard
Vacuum adaptor Battery pack
Bevel scale
Crosscut ruler
Bevel adjustment
knob Base
Trigger switch
LED worklight
Blade
Depth-of-cut quick
adjustment clamp
Lower blade guard lever
Blade screw
Lock-off button
0°Blade
Guide Notch
Spindle lock button
Edge guide lock knob 45°Blade Guide Notch
61325 Manual_Revised_lO 0225 Page 12
PRODUCT SPECIFICATIONS
Motor 12 Volt DC
No-load Speed 2400 RPM
Blade Diameter 3-3/8 in. (85.7mm)
Blade Arbor 15 mm
Cutting Depth at 90 ° 15/16 in.
Cutting Depth at 45 ° 3/4 in.
Bevel Angle Adjustable 00-45 °
Tool weight 3.83 Ibs (without battery)
Battery type Lithium-ion
Battery Voltage 12V DC
Charging Adaptor Input 120-Volts, 60Hz AC only
Optimum charging temperature 32°F (0°C) - 104°F (40°C).
UPPER AND LOWER BLADE GUARD WiTH ANTI=SNAG FEATURE
Heavy-duty, lightweight blade guards provide protection from the blade. The self-
retracting lower blade guard features an anti-snag design for more efficient cutting.
ELECTRIC BRAKE
The saw has an electric brake to quickly stop the blade from rotating.
0 ° TO 45 ° BEVEL ADJUSTMENT
The bevel adjustment lever allows you to set the circular saw for bevel cuts from
0 ° to 45 °.
LED WORKLIGHT
The LED worklight, located on the front of the saw, allows better cut-line visibility.
INTEGRATED RIP AND CROSSCUT RULER
The base has integrated rip and crosscut rulers for quick reference when making
repetitive cuts.
ENLARGED SPINDLE LOCK BUTTON
The spindle lock button allows you to secure the blade when turning the blade screw.
LOCK-OFF BUTTON
The lock-off button reduces the possibility of accidental starting. The button can
be used on either the left or right of the trigger switch.
DEPTH-OF-CUT QUICK ADJUSTMENT CLAMP
The depth-of-cut quick adjustment clamp adjusts the depth of cut a maximum of
0 to 15/16 in. at 90° and 0 to 3/4 in. at 45 °.
61325 Manual_Revised_lO 0225 Page 13
AWARNING: If any part is broken or missing, do not attempt to attach the
battery or operate the saw until the broken or missing part is replaced. Failure to
do so could result in possibly serious injury.
_l_ WARNING: Do not attempt to modify this saw or create accessories not
recommended for use with this saw. Any such alteration or modification is misuse
and could result in a hazardous condition leading to possible serious injury.
_k WARNING: To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the saw when assembling parts.
UNPACKING
This product has been shipped completely assembled.
* Carefully remove the tool and any accessories from the box. Make sure that
all items listed in the packing list are included.
* Inspect the tool carefully to make sure no breakage or damage occurred
during shipping.
* Do not discard the packing material until you have carefully inspected and
satisfactorily operated the tool.
* If any parts are damaged or missing, please refer to the numbers listed on
the back page of this operator's manual.
PACKING LIST
Circular saw, blade (installed on the saw), hex wrench, vacuum adapter, screw,
operator's manual
LOW-BATTERY CAPACITY INDICATOR
If the FuelGauge shines red when the trigger switch on the saw is depressed, the
battery pack power has run out, and the battery pack should be recharged.
Unlike other battery-pack types, Lithium-Ion battery packs deliver fade-free
power for their entire run time. The tool will not experience a slow, gradual loss
of power as you work. To signal that the battery pack is at the end of its run time
and needs to be charged, the power to the tool will drop quickly.
NOTE: The LED may also flash due to an overload or high temperature (see
BATTERY PROTECTION).
61325 Manual_Revised_lO 0225 Page 14
BATTERY PROTECTION
The battery circuitry protects the battery pack from extreme temperature, over-
discharge, and over-charge. To protect the battery from damage and prolong its
life, the battery pack circuitry will turn off the battery pack if it becomes overloaded
or if the temperature becomes too high during use. This may happen in extremely
high-torque, binding, and stalling situations. This intelligent system will shut down
your battery pack if its operating temperature exceeds 176°F (80°C) and will begin
normal operation when it returns to 32°F (0°C) - 104°F (40°C).
The LED light will begin to flash slowly if the battery circuitry detects a
momentary overload.
NOTE: A significantly reduced run time after fully charging the battery pack
indicates that the battery is near the end of its usable life and must be replaced.
COLD WEATHER OPERATION
This Lithium-Ion battery pack will provide optimal performance in temperatures
between 32°F (0°C) and 104°F (40°C). When the battery pack is very cold, it may
"pulse" for the first minute of use to warm itself. Put the battery pack on a tool
and use the tool in a light application. After about a minute, the battery pack will
have warmed itself and will operate normally.
WHEN TO CHARGE THE BATTERY PACK
It is not necessary to run down the battery pack charge before recharging. The
Lithium-Ion battery can be charged at any time and will not develop a "memory"
when charged after only a partial discharge.
Remove the battery pack from the tool when convenient for you and your job.
"Top off" the battery pack charge by charging it for a time before starting a big
job or a long period of use.
Due to Lithium-Ion fade-free properties, the only time it is necessary to charge
the Lithium-Ion battery pack is when the pack has reached the end of its charge.
To signal the end of charge, power to the tool will drop quickly, or the FuelGauge
feature on tools so equipped will indicate diminishing and depleted battery
power. Charge the battery pack as needed.
FueIGauge (Fig.14}
This tool is equipped with a FuelGauge which indicates the battery-pack charge level.
The green LED on the FuelGauge indicates that the battery is fully charged.
The orange LED on the FuelGauge indicates that the battery has used
approximately one half of its charge.
The red LED on the FuelGauge indicates the battery pack is depleted and needs
to be charged.
61325 Manual_Revised_10 0225 Page 15
HOW TO CHARGE THE BATTERY PACK
NOTE: This Lithium-Ion battery pack is shipped partially charged. Before using it
the first time, fully charge the battery pack.
A fully discharged battery pack will charge in about 30 minutes in a surrounding
II
communicate with the |
battery pack to evaluate the
condition of the battery pack.
6. The green light will flash
while the battery pack is
charging. After charging
is complete, the green
LED on the charger will
be on. The flickering red
light indicates a defective
battery or a bad connection
between the battery and
the charger.
7. The battery pack will fully charge if left on the charger, but it will not overcharge.
NOTE: For your convenience, the charger can operate with most generators and
inverters rated at 300 watts or higher.
temperature between 32°F (0°C) and 104°F (40°C).
1. Charge the Lithium-Ion battery pack with the correct charger.
2. Connect the charger to a power supply.
3. Align the raised ribs of the battery pack with the slot in the charger.
4. Insert the battery pack into I
the charger (Fig. 2). Fig. 2
I
5. The charger will
61325 Manual_Revised_lO 0225 Page 16
LED FUNCTIONS OF CHARGER (Fig. 3)
LED INDICATOR
_) H|/LO TEMP.
(SEE MANUAL)
DEFECTIVE [_
BATTERY
BATTERY [_
CHARGING
BATTERY [_
FULL
BATTERY
PACK
Hot/Cold
battery
Defective
Charging
Fully
charged
RED
LED
On
Flashing
Off
Off
GREEN
LED
Off
Off
Flashing
On
ACTION
Charging will begin
when battery returns to
32°F (0°O)-104°F (40°0)
Battery pack or
Charger/Adapter is
defective
Charging
Charging is complete
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the red LED will
illuminate and the green LED will be off. When the battery pack cools down to
approximately 104°F (40°C), the charger will automatically begin charging.
CHARGING A COLD BATTERY PACK
If the battery pack is below the normal temperature range, the red LED will
illuminate and the green LED will be off. When the battery warms to a temperature
of more than 32°F (0°C), the charger will automatically begin charging.
DEFECTIVE BATTERY
If the charger detects a problem, the red LED will begin flashing and the green
LED will be off.
1. If registering as defective, remove and reinsert the battery pack in the
charger. If the LED status reads "defective" a second time, try charging a
different battery pack.
2. If a different battery pack charges normally, dispose of the defective battery
pack (see Maintenance section).
3. If a different battery pack also indicates "defective," the charger may be defective.
BATTERY CHARGING
If the battery pack is being charged within a normal surrounding temperature
range (32 °F to 104°F), the green LED will begin flashing and the red LED will be
off. The battery pack will reach a full charge in 30 minutes.
61325 Manual_Revised_lO 0225 Page 17
BATTERY FULL
If the battery pack is within normal temperature range, the green LED will
illuminate and the red LED will be off. The battery pack is fully charged and
ready to use. The battery pack will fully charge, but will not overcharge, if left on
the charger.
NOTE: Charger may warm with several continuous charge cycles. This is part of
the normal operation of the charger. Charge in a well-ventilated area.
TO ATTACH BATTERY PACK (Fig.4)
1. Align the raised rib on r
the battery pack with the I Fig. 4
grooves of the saw, and
then attach the battery _-L4___d:Z"_,
pack to the saw.
2. Make sure the latch on
the battery pack snaps
unto place and the battery
pack is secured to the saw
before beginning operation.
TO DETACH BATTERY
PACK (Fig. 4) I
1. Depress the battery release
buttons located on the both
sides of the battery pack to
release the battery pack.
2. Pull the battery pack out and remove it from the tool.
,_k CAUTION: when placing the battery pack in the tool, be sure that the raised
rib on the battery pack aligns with the groove inside the saw and that the latches
snap into place properly, improper assembly of the battery pack can cause
damage to internal components.
SAW BLADES
The best of saw blades will not cut efficiently if they are not kept clean, sharp
and properly set.
Using a dull blade will place a heavy load on the saw and increase the danger of
kickback. Keep extra blades on hand, so that sharp blades are always available.
Gum and wood pitch hardened on the blades will slow the saw down. Use gum
and pitch remover, hot water or kerosene to remove these accumulations. DO
NOT USE GASOLINE.
61325 Manual_Revised_lO 0225 Page 18
WARNING: A blade diameter of 3-3/8 in. is the maximum blade capacity of
your saw. A blade diameter greater than 3-3/8 in. will come in contact with the
blade guards. Never use a blade that is so thick that it prevents the outer blade
washer from engaging with the flat side of the spindle. Blades that are too large
or too thick can result in an accident causing serious injury.
BLADE GUARD SYSTEM (Fig. 5}
The lower blade guard attached
to your circular saw is there for Fig. 5
your protection and safety. It
should never be altered for any
reason. If it becomes damaged
or begins to return slowly or
sluggishly, do not operate your
saw until the blade guard has
been repaired or replaced.
Always leave the guard in its
correct operating position when
using the saw. J
--I
_t_ DANGER: When sawing _ --
through a workpiece, the lower
blade guard does not cover
the blade on the underside of the workpiece. Since the blade is exposed on the
underside of the workpiece, keep hands and fingers away from the cutting area. Any
part of your body coming in contact with a moving blade will result in serious injury.
CAUTION: Never use the saw when the guard is not operating properly.
The guard should be checked for correct operation before each use. If you drop
your saw, check that the lower blade guard and bumper for damage at all depth
settings before using.
_t_ WARNING: When using the saw, always stay alert and exercise control. Do
not remove the saw from the workpiece while the blade is moving.
61325 Manual_Revised_lO 0225 Page 19
KICKBACK (Fig.6)
Fig. 6
/ /
Bmade is Set Too Deep Correct Blade Depth
_ DIRECTmONOF CUT_
_KmCKBACK_
Kickback occurs when the blade stalls rapidly and the saw is driven back
towards you. Blade stalling is caused by any action which pinches the blade
in the wood. To avoid kickback, release the trigger switch immediately if blade
binds or saw stalls. Kickback could cause you to lose control of the saw.
Loss of control can lead to serious injury.
To guard against kickback, avoid dangerous practices, such as the following:
1. Setting blade depth incorrectly. See next page for correct setting.
2. Sawing into knots or nails in the workpiece.
3. Twisting the blade while
making a cut. Fig. 7 WRONG!
4. Making a cut with a dull,
gummed up or improperly
set blade.
5. Supporting the workpiece
incorrectly (Fig. 7).
6. Forcing a cut.
7. Cutting warped or wet lumber.
8. Operating the tool incorrectly
or misusing the tool.
9. Attempting to cut with blade INCORRECT SUPPORT
at less than full speed
_, WARNING: If the blade comes in contact with the workpiece before it reaches
full speed, it could cause the saw to "kickback" towards you, which could result in
serious injury.
61325 Manual_Revised_lO 0225 Page 20
To lessen the chance of kickb
1. Keep the blade at the
correct depth setting. The
depth setting should not
exceed 1/4-inch below the
material being cut (Fig. 8).
inspect the workpiece
for knots or nails before
cutting. Never saw into a
knot or nail.
2.
3. Make straight cuts. Always
use a straight edge guide
(sold separately) when rip
cutting. This helps prevent
twisting of the blade.
4. Use clean, sharp and
properly set blades. Never
make cuts with dull blades.
5. Support the workpiece
properly before beginning a
cut (Fig. 9).
6. Use steady, even pressure
when making a cut. Never
force a cut.
7. Do not cut warped or
wet lumber.
8.
Rck:
Fig. 8 Correct blade depth setting
is 1/4-in. maximum or less on
underside of workpiece
[. 1/4-in.
maximum
Fig. 9
CORRECT SUPPORT
Hold the saw firmly with
both hands and keep your
body in a balanced position
so as to resist the forces if kickback should occur.
,_ WARNING: To avoid kickback, release the trigger switch immediately if
blade binds or saw stalls. Kickback could cause you to lose control of the saw.
Loss of control can lead to serious injury.
61325 Manual_Revised_lO 0225 Page 21
LOCK-OFF BUTTON (Fig. 10}
The lock-off button reduces the
possibility of accidental starting.
The lock-off button is located
on the handle above the trigger
switch. The lock-off button
must be depressed before you
pull the trigger switch.
NOTE: The lock-off can be
operated from either the left or
right side.
STARTING/STOPPING THE
SAW (Fig. 10}
To start the saw:
Fig. 10
Lock-off
button
1. Depress the lock-off button.
2. Depress the trigger switch. Always let the blade reach full speed, then guide
the saw into the workpiece.
To stop the saw:
1. Release the trigger switch.
After you release the trigger switch, allow the blade to come to a complete stop.
Do not remove the saw from the workpiece while the blade is moving.
ELECTRIC BRAKE
The saw has an electric brake to quickly stop the blade from rotating. The
electric brake engages when the trigger switch is released. When the brake is
functioning properly, sparks may be visible through the vent slots in the motor
housing. This is normal and is the action of the brake.
NOTE: If the electric brake repeatedly fails to quickly stop the blade rotation, the
saw should be repaired by a qualified service technician at Sears Service Center.
,_ WARNING: Always remove the battery pack from the tool when assembling
parts, changing blade and making adjustments. Failure to obey this warning
could cause serious personal injury.
DEPTH-OF-CUT ADJUSTMENT
Always use the correct blade-depth setting. The correct blade-depth setting for
all cuts should not be more than 1/4-inch below the material being cut. Allowing
more depth will increase the chance of kickback and cause the cut to be rough.
Your saw is equipped with a depth-of-cut scale that provides increased depth-
of-cut accuracy.
61325 Manual_Revised_10 0225 Page 22
TO ADJUST BLADE DEPTH (Fig. 11)
1. Remove battery pack from
the saw.
2. Loosen the depth-of-cut
quick adjustment clamp.
3. Hold the base fiat against
the workpiece and raise
or lower the saw until the
indicator aligns with the
desired depth on the scale.
NOTE: The scale may be
tight; you can adjust the bevel
adjustment knob to loosen
it. Take care not to make the
depth-of-cut quick adjustment
clamp too loose.
4. Tighten the depth-of-cut
quick adjustment
clamp securely.
USING THE LED
WORKMGHT (Fig. 12)
The saw is equipped with a
fixed-position worklight for
better visibility when cutting.
The LED worklight will turn
on when the trigger switch is
depressed. The LED worklight
will turn off when the trigger
switch is released. This
provides additional lighting on
Fig. 11
Depth-of-cut
quick adjust-
ment clamp
I
/
LED worklight
the surface of the workpiece for operation in lower-light areas.
_, WARNING: The worklight aids in illuminating the cut-line. It is not a
substitute for adequate work area lighting. Failure to obey this warning could
cause serious personal injury.
61325 Manual_Revised_lO 0225 Page 23
VACUUM ADAPTER (Fig.13)
Always connect the vacuum
adapter to the saw when
sawing, whether it is attached
to a vacuum or not.
Remove the battery pack from
the saw before mounting the
vacuum adapter.
1. Align the groove on the
adaptor with the rib on
the saw.
2. Put the adapter onto the rib.
3. Tighten the adapter by
turning the screw clockwise.
4. To improve dust extraction
from the working area,
connect the adapter to a
suitable vacuum cleaner.
Fig. 13
Screw \
Fig. 14
FueIGauge (Fig.14)
This tool is equipped with a
FuelGauge which indicates the FuelGauge
battery pack charge level.
The green LED on the
FuelGauge indicates that the
battery is fully charged.
The orange LED on the
FuelGauge indicates that the
battery has used approximately one half of its charge.
The red LED on the FuelGauge indicates the battery pack is depleted and needs
to be charged.
61325 Manual_Revised_lO 0225 Page 24
USING EDGE GUIDE (sold separately) (Fig. 15)
Always use a guide when
making long or wide rip cuts Fig. 15
with your saw. You can use
either a straight edge or use an
edge guide (sold separately).
NOTE: The edge guide can be
used on the left or right side of
the blade. (Fig. 15)
,_ WARNING: Always remove
the battery pack from the
tool when assembling parts,
changing blades and making
adjustments. Failure to obey
this warning could cause
serious personal injury.
1.
2.
Edge guide
Edge guide
lock knob
Place edge guide
through slot
Remove the battery pack from the saw.
Position the edge guide (sold separately) so that the arm with the ruler side
is facing up. Slide the arm of the edge guide through the mounting slots at
the front of the saw base.
3. Adjust the edge guide to the desired width of cut.
4. Tighten the edge guidelock knob.
,_ WARNING: Always securely clamp and support the workpiece. Always
maintain proper control of the saw. Failure to clamp and support the workpiece
and loss of control of the saw could result in serious injury.
5. When using an edge guide, position the face of the edge guide firmly
against the edge of the workpiece. This will help make a true cut without
binding the blade. The edge of the workpiece must be straight for the cut to
be straight. Use caution to prevent the blade from binding in the cut.
NOTE: Do not bind the blade in the cut. It could cause the saw to "kickback"
towards you, which could result in serious injury.
,_ WARNING: If the blade comes in contact with the workpiece before it
reaches full speed, it could cause the saw to "kickback" towards you, which
could result in serious injury.
OPERATING THE SAW
It is important to understand the correct method for operating the saw. Refer
to the instructions in this section to learn the correct and incorrect ways for
handling the saw.
61325 Manual_Revised_lO 0225 Page 25
DANGER: When lifting the saw from the workpiece, the blade is exposed on
the underside of the saw until the lower blade guard closes. Make sure that the
lower blade guard is closed before setting the saw down.
WARNING: To make sawing easier and safer, always maintain proper
control of the saw. Loss of control could cause an accident resulting in possibly
serious injury.
To make the best possible cut (Fig. 16-Fig. 17):
1. Hold the saw firmly.
2. Avoid placing your hand on
the workpiece while making
a cut (Fig. 17).
3. Support the workpiece
so that you are always
standing to one side of the
cut (kerf).
4. Support the workpiece near
the cut.
Fig. 16
5. Clamp the workpiece
securely so that the
workpiece will not move
during the cut.
6. Always place the saw Fig. 17
weight on the side
of workpiece that is
supported, not on the side
that will fall off when the
cut is completed.
7. Place the workpiece with
the "good" side down.
NOTE: The "good" side of the
workpiece is the side where
appearance is important.
8. Draw a guideline along the
desired line of cut before
beginning your cut.
NOTE: Do not touch the blade to the workpiece until the saw has reached
maximum speed.
WARNING: if the blade comes in contact with the workpiece before it
reaches full speed, it could cause the saw to "kickback" towards you, which
could result in serious injury.
61325 Manual_Revised_lO 0225 Page 26
WARNING: Always securely clamp and support the workpiece. Always
maintain proper control of the saw. Failure to clamp and support the workpiece
and loss of control of the saw could result in serious injury.
iNTEGRATED CROSSCUT RULERS
Marked along the base across the front of the saw is a ruler for measuring
repetitive cuts. It is marked 1-inch to the left of the 0° and 2-1/2 inches to the
right of 0° in 1/8-inch increments.
A ruler for measuring length of cuts is marked along the left side of the base. It is
marked 0 to 8 inches in 1/8-inch increments.
NOTE: The distance from the line of cut to the guideline is the amount you
should offset the guide.
MAKING CROSS CUTS AND RiP CUTS (Fig. 18)
1. Always use your saw with your hand positioned correctly.
,, Line of cut
0° Indicator
2. When making cross or rip cuts, align your line of cut with the right side of
the notch by the 0° indicator.
3. Because the thicknesses of blades vary, make a trial cut in scrap material
along the guideline to determine how much, if any, you should offset the blade
from the guideline to allow for the kerf of the blade to get an accurate cut.
,_ WARNING: If the blade comes in contact with the workpiece before it
reaches full speed, it could cause the saw to "kickback" towards you, which
could result in serious injury.
NOTE: Do not bind the blade in the cut. It could cause the saw to "kickback"
towards you, which could result in serious injury.
61325 Manual_Revised_lO 0225 Page 27
MAKING RiP CUTS
Always use a guide when making long or wide rip cuts with your saw. You can
use either a straight edge or use the edge guide (sold separately).
1. Secure the workpiece.
2. Clamp a straight edge to the workpiece using C-clamps.
3. Carefully guide the saw along the straight edge to achieve a straight rip cut.
_, WARNING: Always securely clamp and support the workpiece. Always
maintain proper control of the saw. Failure to clamp and support the workpiece
and loss of control of saw could result in serious injury.
TO ADJUST
BEVELSETTING (Fig. 19) Fig. 19
1. Remove battery pack from
the saw.
2.
3.
4.
Loosen the bevel
adjustment lever.
Raise the motor housing
end of the saw to the
desired angle setting on the
bevel scale.
Tighten the adjustment
lever securely.
MAKING A BEVEL CUT (Fig. 20)
,_ WARNING: Always securely clamp and support the workpiece. Always
maintain proper control of the saw. Failure to clamp and support the workpiece and
loss of control of the saw could result in serious injury.
Fig. 20
Line of cut
,,
,, 45 ° indicator
1. Your saw can be adjusted to cut at any angle between 0°and 45 °.
61325 Manual_Revised_lO 0225 Page 28
2. There is a notch in the saw base to help you line up the blade with the line
of cut when making 45 ° bevel cuts, Align your line of cut with the left side of
the notch by the 45 ° indicator.
3. Because blade thicknesses vary and different angles require different
settings, make a trial cut in scrap material along the guideline to determine
how much, if any, you should offset the blade from the guideline to allow for
the kerf of the blade to get an accurate cut.
4. When making a bevel cut, hold the saw firmly with both hands.
5. Rest the front edge of the base on the workpiece, then depress the lock-off
button and squeeze the trigger switch to start the saw.
6. Always allow the blade to reach full speed, and then guide the saw into
the workpiece.
7. After completing your cut, release the trigger switch and allow the blade
to come to a complete stop in the cut. Do not remove the saw from the
workpiece while the blade is moving. It will damage your bevel cut and
cause Kickback.
WARNING: If the blade comes in contact with the workpiece before it reaches
full speed, it could cause the saw to kickback towards you, possibly resulting in
serious injury.
MAKING A POCKET
CUT (Fig. 21) Fig. 21
WARNING: Always adjust
the bevel setting to zero
before making a pocket cut.
Attempting a pocket cut at any
other setting can result in a loss
of control of the saw, which can
result in serious injury.
1. Adjust the bevel setting to
zero, set the blade to the
correct blade depth setting,
then use the lower blade
guard lever to swing the
guard up.
WARNING: Always raise the lower blade guard with the lever to avoid
serious injury.
2. While holding the lower blade guard up by the lever, firmly rest the front of
the saw base flat against the workpiece with the rear handle raised so the
blade does not touch the workpiece.
3. Depress the lock-off button and squeeze the trigger switch to start the saw.
Always let the blade reach full speed, and then slowly lower the blade onto
the workpiece until the base is flat against the workpiece. As the blade
enters the material, you must release the lower blade guard lever.
61325 Manual_Revised_10 0225 Page 29
4. After you complete the cut, release the trigger switch and allow the blade to
come to a complete stop. After the blade has stopped, remove it from the
workpiece. If the corners of your pocket cut are not completely cut through,
use a hand finishing saw to finish the corners.
,_ WARNING: Never tie the lower blade guard in the raised position. Leaving
the blade exposed could result in serious injury.
,_ WARNING: When servicing, use only identical Craftsman replacement parts.
Use of any other parts may create a hazard or cause product damage.
WARNING: Always wear safety goggles or safety glasses with side shields when
using compressed air to clean tool. If the operation is dusty, also wear a dust mask.
,_, WARNING: To avoid serious personal injury, always remove the battery
pack from the tool when cleaning or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible
to damage from various types of commercial solvents and may be damaged by
their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
,_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result in serious personal injury.
Only the parts shown in the parts list are intended to be repaired or replaced by
the customer. All other parts should be replaced at a Sears Service Center.
CHANGING THE BLADE (Fig. 22)
Fig. 22
Spindle lock button
WARNING: Be sure to wear protective work gloves while handling a saw
blade. The blade can injure unprotected hands.
61325 Manual_Revised_lO 0225 Page 30
1. Remove the battery pack from the saw.
2. Loosen the depth-of-cut adjustment lever. Raise the saw to its maximum
height and tighten the depth-of-cut adjustment lever. This practice
permits easier access to the blade mounting.
3. Locate and remove the hex key from the storage area.
4. Depress the spindle lock button and place the hex key in the blade screw and
move it back and forth until you feel the spindle lock button depress further.
This action locks the blade in position so that the blade screw can be removed.
5. With the spindle lock button firmly depressed, turn the blade screw
clockwise to loosen it.
6. Raise the lower blade guard using the blade guard lever and hold it in the
raised position.
7. Remove the blade screw and the outer blade washer and the blade.
8. The remaining washer is the inner bushing washer that fits around the
spindle shaft and does not need to be removed.
9. Put a drop of good-quality machine oil onto the inner bushing washer and
outer blade washer where they will contact the blade.
10. Place a new saw blade inside the lower blade guard, onto the spindle shaft
and against the inner bushing washer.
NOTE: The teeth of the blade should point upward at the front of the saw.
11. Replace outer blade washer.
12. Depress and hold spindle lock button as you replace the blade screw and
hand tighten the screw in a counterclockwise direction. Use the hex key to
tighten the blade screw securely.
13. Return hex key into the storage area.
NOTE: Never use a blade that is too thick to allow the outer blade washer to
engage with the fiat side of the spindle.
BATTERI ES:
The battery pack is equipped with Lithium-Ion rechargeable batteries. The
duration of use from each charge will depend on the type of work performed.
The batteries in this tool have been designed to provide maximum trouble-
free life. Like all batteries, they will eventually wear out. Do not disassemble
the battery pack or attempt to replace the batteries. Handling of the batteries,
especially when wearing rings and jewelry, could result in a serious burn.
To obtain the longest possible battery life, read and understand the operator's manual.
• It is good practice to unplug the Charger and remove the Lithium-Ion battery
pack when not in use.
For Lithium-Ion battery pack storage longer than 30 days:
Store the Lithium-Ion battery pack where the temperature is below 80°F
(26°C) and free of moisture.
61325 Manual_Revised_lO 0225 Page 31
• Store Lithium-Ion battery packs in a 30%-50% charged condition.
Every six months of storage, fully charge the Lithium-Ion battery pack.
Exterior may be cleaned with a cloth or soft non-metallic brush.
BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING
To preserve natural resources, please recycle or dispose
of batteries properly. This product contains lithium-ion
batteries. Local, state or federal laws may prohibit disposal
of lithium-ion batteries in ordinary trash. Consult your
local waste authority for information regarding available
recycling and/or disposal options.
,_ WARNING: Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not attempt to
destroy or disassemble battery pack or remove any of its components.
Lithium-ion batteries must be recycled or disposed of properly. Also, never
touch Keep away from children. Failure to comply with these warnings could
result in fire and/or serious injury.
PROBLEM CAUSE
The circular saw Battery pack is depleted
does not work The battery pack is not
installed
The blade does
not follow a
straight line
Teeth are dull. This is caused
by hitting a hard object such as
a nail, dulling teeth on one side.
The blade tends to cut to the
side with the sharpest teeth.
SOLUTION
Charge the battery pack
Install a charged battery
pack
Change to a new sharp
blade
Edge guide or straight edge is Use an edge guide or
not being used. straight edge
The blade binds Blade is dull. Change to a new sharp
or smokes from blade
friction Blade is on backwards. Install the blade correctly
Blade is bent. Replace with a new blade
Workpiece is not properly Clamp the workpiece
supported, correctly and tightly
Incorrect blade is being used. Use the correct blade
61325 Manual_Revised_lO 0225 Page 32
12.0=VOLT LITHIUM-ION CORDLESS 3=3/8=in. CIRCULAR SAW
MODEL NO. 320.61325
The Model Number will be found on the Nameplate attached to the handle of the
circular saw. Always mention the Model Number when ordering parts for this tool.
61325 Manual_Revised_lO 0225 Page 33
12.0=VOLT LITHIUM-ION CORDLESS 3=3/8=in. CIRCULAR SAW
MODEL NO. 320.61325
The Model Number will be found on the Nameplate attached to the handle of the
circular saw. Always mention the Model Number when ordering parts for this tool.
1 5620041000 Screw 1
2 3125169000 Vacuum Adapter 1
3 5610024000 I Tapping Screw 7
4 3402418000 Upper Guard 1
5 5620425000 Flange Screw 1
6 3704673000 Outer Flange 1
7 3125170000 Lower Guard 1
8 3810474000 Blade 1
9 3520509000 Inner Flange 1
10 3650115000 Circlips For Shaft 1
11 3660429000 Torsion Spring 1
12 5660001000 E Ring 2
13 3125173000 Lock Lever 1
14 3551457000 Shaft 1
15 3551441000 Pin 1
16 5630242000 Round Nut 1
17 5650339000 Washer 1
18 3125174000 Upper Guard 1
19 3320987000 Left Housing 1
20 5610106000 i Tapping Screw 8
21 3402417000 Gear Case Cover 1
201 2822832000 Shaft Assembly 1
22 3551434000 Shaft 1
23 3551435000 Gear 1
202 2822831000 Gear Set 1
61325 Manual_Revised_lO 0225 Page 34
24 3551436000 Bevel Gear 1
25 3551437000 Gear Shaft 1
26 3520510000 Oil Impreging Bearing 2
27 3402422000 Gear Case 1
28 3704254000 Hand Hoop 1
29 5630243000 Hexagon Nut 1
30 3402298000 Contact Receptacle Assembly 1
203 2822833000 Motor & Gear Assembly 1
31 2730158000 DC Motor 1
32 3551438000 Pinion 1
33 5620039000 Screw 2
34 4870438000 i Trigger Switch 1
35 3660075000 Spring 1
36 3125308000 Lock-off Trigger 1
37 3125136000 Light Guide Pole 1
38 3320988000 Right Housing 1
39 5610103000 i Tapping Screw 10
204 2822805000 Base Plate Assembly 1
40 3704671000 Base Plate 1
41 5680008000 Rivet 2
42 3704672000 Depth Bracket 1
43 3704675000 Support Plate 1
44 3704674000 i Angle Support 1
45 5630189000 Hexagon Nut 1
46 5620033000 Screw 1
47 4890641000 PCB Assembly 1
48 3124378000 LED Cover 1
49 5620427000 Bolt 1
50 3660071000 Spring 2
51 3402419000 Spindle Lock Button 1
61325 Manual_Revised_lO 0225 Page 35
52 5640019000 Square Neck Bolt 1
53 5650016000 Plain Washer 1
54 5630241000 Wing Nut 1
55 5640196000 Wing Bolt 1
56 5680031000 Hexagon Wrench 1
57 5630188000 Nut 1
58 5660005000 E Ring 1
61325 Manual_Revised_lO 0225 Page 36
Your Home
For troubleshooting, product manuals and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4=MY-HOME ® Ca, anytime, day or night
(1-800-469-4663) (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
"' For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca
TopurchaseaprotectionagreementonaproductservicedbySears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Pard pedirserviciode reparaci6n Au Canada pour serviceen fran£ais:
i a domicilio,y pardordenar piezas: 1.800.LE.FOYERMe
=; 1-888-SU-HOGAR® (1-800-533-6937)
(1-888-784-6427) www.se a rs.o a
i www.sears.com
...... SealrN
TM
® Registered Trademark /Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
TK
® Marca Registrada /'_Marca de Fabrioa de KCD IP, LLC an Estados Unidos, o Sears Brands, LLC in otros paises
MD
_,_cMarque de commerce /Marque depos6e de Sears Brands, LLC

Navigation menu