Craftsman 351181720 User Manual NAILER Manuals And Guides L0308386

CRAFTSMAN Nailer Manual L0308386 CRAFTSMAN Nailer Owner's Manual, CRAFTSMAN Nailer installation guides

User Manual: Craftsman 351181720 351181720 CRAFTSMAN NAILER - Manuals and Guides View the owners manual for your CRAFTSMAN NAILER #351181720. Home:Tool Parts:Craftsman Parts:Craftsman NAILER Manual

Open the PDF directly: View PDF .
Page Count: 10

RightFax 8/15/2003 1:18 PAGE 2/11 Righ%Fax

:Colovos l

Operator's Manual

18 Gauge

-21/8"Length

BRAD NAILER

Model No.

351.181720

CAUTION: Read and follow

all Safety Rules and Operating

Instructions before First Use

of this Product, Keep this

manual with tool.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.seors.comlcreftsman

20317.01 Draft (04/24/03}

• Safety

•Operation

• Maintenance

•Parts List

•Espafiol

R±ghtF&× 8/15/2003 1:18 PAGE 3/11 RightFax

Warranty ......................................... 2

Safety Rules ...................................... 2

Operation ...................................... 3-5

Maintenance .................................... 5-6

Troubleshooting ................................... 7

Parts IIlustratton and List .......................... 8-9

Espa_ol ...................................... 10-15

FULL ONE YEARWARRANTY

If Dis product falls due to adefect In mateidal or workmanship

wi_ln one year from _date of pumheae, Sears will at Its

option repair or replace It free of charge. Contact your nearest

Sears Service Center {1-800-4-MY-HOME) to arrange for prod-

uct repair, or return this product to place of purchase for

replacement.

If this product Is used for commercial or rental purposes, this

warranty will apply for 90 days from the date of purchase.

This warranty aepllas only while tlds product is used In the

United States,

This warranty gives you specific legal dghts, and you may also

have other rights which vary from state to state.

Sears, Roobuck and Co., Dept. 817WA, Hoffman Estates,

IL 60179

Read and follow all safety rules and operating instructions

in this manual and on warning label of tool before using

this tool. Keep this manual with the tool.

Keep work area cJean and properly lighted.

• Keep children, bystanders end visitors at asafe distance

from work area while operating this tool.

• Air tool operators and all others In work area should

always wear safety goggles complying with United States

ANSI Z87.1 to prevent eye Injury from fasteners and flying

debris when loading, operating and unloading this tool.

Everyday eyeglasses have only impact resistant lenses.

These are NOT safety glasses. ANSI Z87.1 safety glasses

have permanently attached rigid, hard plastic side shields

and will have "ZBT.I" printed or stamped on them.

• Always wear ear protection. The work area may include

exposure to excessk-_e noise levels which wilt require nec-

essary ear protection. Some enwronmeots will require

head protecBon; use head protection conforming to ANSI

Z89.1.

• DO not alter or modify this tool in any we:( Do not use this

tool for any application other than for which it was

designed,

• Do not use oxygen, carbon dioxide, high-pressure com-

pressed gas or bottled gases as the power source for this

tool. The tool will explode and serious personal injury

could result.

Never connect the tool to air pressure which could potan-

ttatly exceed 200 psi. Use only clean, dry, regulated air

within rated range as marked on tool.

•The tool must have a male, free-flow hose coupling so that

all air pressure is renmvad from the tool when the coupling

joint is disconnected. Failure to use proper coupling could

cause ac_dente) dlscharge,possibly causing injury.

•Only use air hose that is rated for a maximum working

pressure of 15G ps( or 150% oftbe maximum system pres-

sure, whichever is greater.

•Do not use a hose swivel connector with _is tool.

•Do not putt trigger or depress contact trip white connecting

to the air supply, as the tool may cycle, possibly causing

injury

•When loading tool: Do not puFI trigger or depress contact

trip; DO not point the tool at yourself or others; Do not

place hand or any part of body in the fastener discharge

area of the tool as accidental actuation may occur and

cause thjur_:

*Disconnect tool from air supply betore loading or unload-

ing, performing tool maintenance, clearing a jammed t'as-

tenet, fea_ng work area, moving tool to another location or

handing the tool to another person.

•Use Sears recommended fasteners only.

•Do not load the teal until you are ready to use It.

•Always assume that the tool contains fasteners. Keep _e

tool pointed away from yourself and others at all times.

Never engage Lnhorseplay. Never pull the thgger unless

the contact frfp is In contact wtth the workplace. Keep oth-

ere at a safe distance from the tool while the tool Is In

operation.

•Always remove finger from trigger when not driving fasten-

ers. Never carry the tool with finger on or under the trigger

as accidental actue_lon may oo_ur and cause Injury.

•Always keep hands and body away from the fastener dis-

charge area when air supply is connected to the tool. Grip

too/firmly to maintain control whl_e allowing tco9 to recolJ

away from work surface as fastener Is driven.If contact trip

Is allowed to recontact work surface before trigger Is

released, an unwanted fastener may be driven.

•Check operation of the c_ltact thp frequently. Never use

the tool if the contact thp, trigger or eprlnge have become

Inoperable, mtsslng or damaged. Do not altar or remove

contact tap, trigger or springs. Never use a tool that is leak-

ing air, has missing or damaged parts, or requires repair

•Do not drive fasteners on top of other fasteners or with the

tool at too steep an angle. The fasteners can dcechet and

cause Injury DO not drive fasteners close to the edge of

the workplace. The workpteos is likely to split, allowing the

fastener to tty free and cause injury DO not attempt to

drive fasteners into hard or brittle materials such as con-

crete, steal or tile.

•Do not overreach. Always piece yourself in a firmly bal-

anced position when using or handling the tool. Do not

attach the hose or tool to your body.

•Do not operate tnol w_thout fasteners or damage to too)

may result.

• Do not use tool without safety wamthg label If labe) is

missing, damaged or unreadable, conteot SEARS to

obtain anew label.

•Only qualified repair personnel must perform tool service.

• When servicing a too/. use only JdantJcalrepair parts,

• Store toni out of reach of children and other untrained

persons.

O _ears, Roebuck and Co. 2

KightFax 811512003 1:18 PAGE 4111 RightFax

DESCRIPTION

The Craftsman 18 Gauge Brad Nailer drives brads from %" to

2%" long. Oiltass design eliminates daily oiling and oil stains

on workpiece. Die cast magnesium body with textured rubber

grip minimizes operator fatigue. I_rga capaoi_ side leading

magazine with posilNe, quick action latch makes loading easy.

Nailer features rear exhaust, single and rapid-fire operation,

adjustable depth of drive control, rubber nose tip and storage

case. Salty feature disabtes toot unless contact tdp is pressed

against workptece. Tapered nosepiece provides operator with

greater visibility for precme fastener placement Rigid nose-

piece reduces jamming. The 18 Gauge Brad Nailer is excellent

for molding, furniture making, and picture fremlng.

SPECIFICATIONS

Capacity .............................. 100 brad nails

Nail size ...................... 18 gauge (.040" x .040 ")

Nail lengths ................................ % to 2_"

Operating pressure ........................ 60-100 PSI

Air inlet.................................... Y," N.P.T.

Length ........................................ 9Vz"

Height ........................................ 9_ =

Width ......................................... 2_t_,_

Weight ..................................... 2.7 Ibs.

BRAD NAILS

18341 {Box of 5000) ......... 18 gauge brad nails, %" long

19171 {Box of 1000) ......... 18 gauge brad nails, %" long

18342 (Box of 5000) .......... 18 gauge brad nails, 1" long

19172 (Box of 1000) .......... 18 gauge brad nails, 1" long

18343 (Box of 5000) .....

19173 (Box of 1000) .....

18360 [Boo( of 5000) .....

19174 (Box of 1000) .....

18361 (Box of 5000) .....

18362 (Box of 5000) .....

19176 (Box of 1000) .....

AIR SUPPLY LINE

Rater to Figure 1.

.18 gauge brad nails, 1%" long

18 gauge bred nails, 1%" long

.18 gauge bred nails, 1%" long

•18 gauge bred nails, 1½" long

• 18 gauge brad nails, 1%" long

... 18 gauge brad nails, 2" long

DANGER: Do not use oxygen, carbon dioxide, high-pressure

compressed gas or hotttad gases as the power source for this

tool. The tool will explode and serious personal injury coutd

resutt.

The air tool operates on compressed sir at pressures from

60 to 100 PSI.

Never connect the tool to air pressure which could poten-

tially exceed 200 PSI. Use only clean, dry, regulated air

within rated range as marked on tool.

Air Delivery Required: 0.94 SCFM @ 90 PSI

(30 shots per minute),

WARNING; Keep hands and _ away from discharge area

of tool when connecting air supply. Always disconnect tool

from air supply when servicing or adjusting tool and when tool

Is not in use.

•Air operated tools require cJesn, dry, lubricated com-

pressed air to ensure top performance, low maintenance

and long life.

Dirt and abrasive materials present in all air lines will dam-

age tool O-rings, valves and cylinders.

Moisture will reduce tool performance and life if not

removed from cornprassecl air.

•A filter-ragulator-lubricator system is required and should be

located as dose to tool as possible. A distance of tess than

15 feet is recommended. Lubricator is not required for

oittess tools.

•Keep air filter clean. A dirty filter will reduce the air pressure

to the tool causing a reduction in power and efficiency.

•The air supply system must ha able to provide air pressure

of 60 to 100 pounds per square Inch st tool

•All hoses and pipes In the air supply system must be clean

and free of moisture end foreign pertisies. Hoses must be

rated for s maximum woddng pressure of 150 PSI or 150%

of maximum system pressure, whichever is greater,

• Do n_ mou_ swivel contractor in air supply line.

•The air pressure should be properly regulated,

•Oifferent workptece mate_ls and different fastener lengths

will require different operating pressure.

•Be sure a= conneoitons in air supply system are sealed to

prevent air toss.

•Never connect a female quick-disconnect coupling to the

tool side of air line connection. A male, free-tim coupling

should be connected to the tool side of air freeconnection

(see Figure 1).

WARNING: The female coupling provides a seal preventing

loss of compressed air from compressor tank when discon-

net.fad from msie coupling, if connected to tool s{de of air

supply, the farnate ooupling could seal acompressed air

charge in the tool which could discharge if the tool trigger is

actuated.

Figure I -Air Supply Line

Refer to Figures 2, 3 & 4 (page 4).

WARNING: Disconnect tool from air supply. Oo not load tool

until you are ready to use it. Do not ppll trigger or depress

contact tripwhile loading tool. Always load with nose of tool

pointing away from you and others. Always wear ssfaly gog-

gles that comply with United States ANSI Z87.1.

NOTE: For best results, use Sears fasteners only.

RightFax 8/15/2003 1:18 PAGE 5/11 RightFax

• Depress latch and slide magazine cover open (see

Figure 2).

F;o.I.O.o.a0=..

•Insert fasteners into magazine. Position fasteners at bottom

of magazine with head towards top of tool (see Figure 3).

Figure 3 -Load Magazine

•Slide magazine cover forward over magazine until latch

snaps Into place, locking magazine cover (see Figure 4),

Figure 4 - Close Magazine

NAILING OPERATION

Refer to Figures 5, 6, 7 & 8 (pages 4 and 5).

WARNING: Read and fonow all safety rules and operating

instructions in this manual and on warning label of too_ before

using this tool. Keep this manual with the tool.

WARNING: Do not use this tool wift_Jt safety warning

isbel. If label is ndssw,g, damaged or unreadable, contact

Seam to obtain a new label.

WARNING: Never operate tool unless contact trip is in con-

tact with wod_pisce. Do not operate toot without fasteners or

damage to tool may result. Never fire fasteners into the air

because fasteners may injure operator or others and damage

to tool may result.

•Pertorm "Safety Mechanism Check" as described in the

Maintenance sec_on (see page 6) prior to first use of tool

and on a daily basis thereafter.

• The tool is equipped with arotating switch that can be set

to rapid-fire orstogle-fire mode (see Figure 5). When the

switch is set to single-fire mode, the tool will not drive a

second fastener until the trigger is fully released and

pulled again.

•When the switch is rotated to rapid-fire mode. the tool can

drive fasteners continuously. A fastener will be fired each

time the contact top is pressed against the workpmce, as

long as the _='kJgeris maintained in the pulisd position.

Figure 5 - Push and rotate swltoh to select

Operation Mode

SINGLE-FIRE OPERA1]ON;

•The air tool is equipped with a contact trip safety mecha-

nism that disables too# unless_sct lrip is pushed

against work. To drive a fastener hold body firmly and

press contact tnp on workpisce where fastener is to be

applied. Pull trigger to ddve fastener into workplace. To fire

a second fastener lilt the tool from the workpisce, release

the trigger and then repeat the above sequence.

RAPID-FIRE OPERATION:

•The toal can also be operatad by holding bigger

depressed and pushing contact trip against workplace. A

fastener will be driven each time the cordact trip is pushed

against the workplece. This opera_ng procedure provides

rapid-fire fastener ddving. Never operate tool unless con-

tact b'ip is in contact with workpisce.

RightFax 8/15/2003 I:18 PAGE 6/ii RightFax

WARNING: All air power fastening tools recoil when operat-

ed. This recoil is CaUSed by rapid driving of the fe.stanen Tool

may bounce from recoil causing a second unwanted fastener

to be driven. Reduce tacd bounce by holding too( firmly in

hand and pressing tool gently against workplace. Let the tool

do the work. This will allow recoil of tool to bounce tool away

from workpisce preventing the ddving of second fastener,

CONTACT TRIP ADJUSTMENT

The contact hip may be adjusted up or down to vary the

depth of the tastener in the workpiece. To adjust, rotate depth

contr_ knob _see Figure 6) to raise or I_er contract t_p to

desired setting.

ura 6 -Setting Dept_ Control

Knob

CONTACT TRIP PAD

The tool is equipped with a contact trip pad (see Figure 7)

that prevents marring of finished surfaces by the contact trip

during normal operation. Pad can be removed and stored on

the storage sleeve located on the and cover of the magazine,

Hex wrench is also stored on the magazine.

Flgura 7 - Storteg Contact Tdp Pad and Wrench

LOAD INDICATOR

The tool is equipped with a load indicator, The load indicator

(colored red) will be visible through the magazine cover win-

dow when there are oo fasteners in the magazine.

Figure 8 - Load Indicator

OPERATING PRESSURE

•Use only enough air pressure to perform the operation. Air

pressure in excess of that which is required will make the

operation Lneffident ar_l may cause premature wear or

damage to the toot.

•Determine minimum air pressure required by driving some

test fasteners into the wodkoiece. Set air pressure so that

test fasteners are ddvan down flush with the work surface.

Fasteners driven too deep may damage workpieca.

COLD WEATHER OPERATION

CAUTION: Do not store In cold environment. Frost or ice

could form Inside tool affecting operation and damaging tool.

Use acold temperature lubricant, such 8s ethylene glycol,

when operating tool In freezing temperatures.

Refer to Figure 9 (page 8).

LUBRICATION

This isan oilissstool.No lubricationis necessary.

MAGAZINE AND PISTON-RAM

• Keep magazine and nose of tool dean and free of any dirt,

lint or abrasive particles.

Tho tip of the ram (Fig. 9, No, 11) can become dented or

rounded over time,

-Square off the tip of the ram with a clean, fine hand file to

=tend the itfa of the ram and tool. Fastener firir_ v(dl be

more consistent if the ram tip is kept clean and square.

RightFax 811512003 I:18 PAGE 7111 RightFax

SAFETY MECHANISM CHECK

Inspect contact trip safety mechanism daily for proper opera-

tion Do not operate tool if mechanism is not operating

properly

With the red push-button switch in the rapid-fire mode, per-

form the fo_towing procedures to test safety mechanism:

• Leave trigger untouched while pushing contact trip Into

workpiece Tool must not fire.

• Pull trigger while contact trip Is dear of wolf and pointed

away from operator and o'_ers. Tool must not fire.

• Depress and hold trigger, push contact trip against work

where _stener is needed. The tool should drive only one

lastener each time the contact trip is pushed against

workpiece

If co.tact t_lp mechanism does not operate properly,

repair tool Immediately through Sear/Servloa Center.

Replace any damaged or missing parts. Usa the parts list to

order parts.

REBUILD KITS

Rebuild kits ere available as spare ports, (see page 9}. Tools

should be rebuilt ff tool falls to operate properly after e_fanded

use. See troubleshooting to determlse required replacement

parts

Disconnect tool from air supply before attempting repair

or adjustment.

NOTE: When replacing O-rings or cylinder, lubricate with

grease before assembly

KightF_x 811512003 1 :18 PAGE 8111 RightFax

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Trigger cap leaks air 1. O-ring damaged 1. Check and replace damaged O-ring (Fig. 9, No. 55)

2. Valve stern, seal or O-rings damaged 2. Check and replace damaged stern, se_l or O-rings

(Fig. 9, Nos. 55, 56, 57 and 60)

Cap leaks air 1. Cap bolts toose 1. Tighten bolts (Fig 9, No. 1)

2. Damaged gasket 2. Check and replace damaged gasket (Fig. 9, No. 3)

Nose leaks air 1. Damaged cylinder O-ring 1. Check and replace damaged O-ring (Fig. 9, No. 12)

2. Damaged bumper 2. Check and replace damaged bumper {Fig. 9, No. 14)

3. Ram guide damaged 3. Check and replace guide (Fig. 9, No. 15)

Tool will not operate 1. Insufficient air supply 1. Check air supply

2. Damaged or worn heed valve O-dng 2. Replace damaged or worn O-ring or seal

or seal (Fig, 9, Nos. 5 and 9)

3. Damaged head valve spring 3. Replace damaged spring (Fig. B, No. 6)

4. Head valve binding in cap 4. Clean and grease cap and head valve

(Fig, 9, Nos. 2 and 9)

Tool operates slowly

or loses power

Tool skips fasteners or

nconsistsnt operation

1. Damaged head valve spring

Z Damaged or worn O_ngs

3. Damaged trigger assembly

4. Build-up on ram

5. Cylinder not sealed on bumper

propedy

6. Insufficient air supply

7. Head valve poorly lubricated

1. Worn ordamaged bumper

2. Build-upon ram or nose

3. Insufficient air supply 3.

4. Damaged or warn piston O-ring 4.

5. Damaged magazine springs 5.

6, Magazine-nose bolts loose 6.

7. Fasteners too short

8. Damaged fasteners

9. Inconect fastener size

10. Cap leaks

11. Damaged trigger valve seal and

O-rings

12. Bent or damaged ram

13. Dirty magazine

14. Damaged orwom magaslne

1. Check and replace damaged swing (Fig 9, No 6)

2. Check and replace damaged or worn O-dr_ja

3. Check and replace trigger assembly

4. Clean piston/ram assembly (Fig. 9, No. 11)

5. Disassemble cylinder and assemble properly

6. Check air supply

7. Disassemble heed valve (Fig. 9, No. 9),

dean, grease, and assemble properly

1. Check and replaCe bumper (Fig, 9, No. 14)

2. Clean and grease piston/ram assembly (Fig. 9, No. 111

and inside of nose cover (Fig. 9, No. 21)

Check air supply

Check and ragl_ca O-ring (Fig. 9, No. 10)

Chedx and replica springs (Fig. 9, No, 34]

PJlgn nose wffh magazine and tighten bolts

(Fig. 9, No. 24)

7. Use Sears recommended fasteners only

8. Discard damaged fasteners

9. Use Sears recommended fasteners only

10. Tighten cap bolts [Fig. 9, No. 1). Check and replace

damaged gasket [Fig. 9, NO. 3)

11. Check and replace damaged seal and O-rings

(Fig. 9, Nos. 55, 57 and 60)

12. Check and replace damaged piston/ram assembly

(Fig. 9, No. 11)

13. Clean magazine and lubricate with a

dry, film lubricant.

14. Check and replace magaslne (Fig, 9, No. 37)

8/t5/2003 _:18 pAGE 9/11 RightFax

gigh_FaX

Model 351.181720

Figure9.ReplaoementPa_slllu_ra_°nF°rNailer

27 t

30 25 31 32

RightFax 8/15/2003 1:18 PAGE I0/II RightFax

KEY

NO. PART NO. DESCRIPTION QTY.

106395.0O 4-0.7 x 22ram Socket Head Bolt 7

2 20272.0O Cap

3 20273.00 Gap Gasket

4 20274.00 Spacer 1

5 20275.00 Seal 1

604210.00 Head Valve Spdng 1

706436.00 Spacer 1

8 04303.00 33,5 x 2.0mm O-Ring 1

9 04302.00 Head Valve Piston 1

10 20277.00 Seal 1

11 20278.00 Piston Ram Asceml_J 1

12 06909.00 44.17 x 1.78mm G-Ring 1

13 20279.00 Cylinder 1

14 20280.00 Bumper 1

15 20281.00 Ram Guide 1

16 20282.00 Throttle 1

17 20283.00 Contact Trip Guide 1

18 20284,00 Pad 4

19 20285.00 Contact Trip 1

20 20286.00 Contact Trip Pad 1

21 20287.00 Nose Cover 1

22 04345.00 Shoulder Screw 2

23 06079.00 4-0.7 x l_-nm Socket Head Bolt 1

24 20288.00 Nose 1

25 20895.00 2 x 12ram Spring Pin 4

26 20289.00 Left Plate 1

27 20290.00 Pusher 1

28 20291.00 Load indicator 1

29 20364,00 Feed Ring 1

30 06088.00 4-0.7 x 10ram Socket Head Bolt 1

31 20292.00 Right Plate 1

32 20293.00 Nut 1

33 2029400 Magazine Cover 1

34 20295.00 Pusher Spdng 1

35 20296.00 Wear Plate 1

36 20297.00 Lever Lock 1

37 20298.00 Magazine 1

Standard hardware item available locally

Not Shown

Recommended Accessories Qty.IBox Model No

18 Gauge Brad Nails, sH' Long 5000 9-18341

18 Gauge Brad Nails, %" Long 1000 9-19171

_, 18 Gauge Brad Nails, 1" Long 5000 9-18342

_, 18 Gauge Brad Nails, 1" Long 1000 9-19172

18 Gauge Brad Nails, 1_,_"Long 5000 9-18343

18 Gauge Brad Nails, lY." Long 1000 9-19173

_. 18 Gauge Brad Nails, l'h" Long 5000 9-18360

_- 18 Gauge SradNalls, 1'/="Long 1000 9-19174

18 Gauge Brad Nails, 1¾" Long 5000 9-18361

A18 Gauge Brad Nails, 2" Long 5000 9-18362

A18 Gauge Brad Nails. 2" Long 1000 9-19176

KEY

NO. PARTNO.

060O6.0O

2029g.00

17437.CO

2024E0O

20300.00

20301.0O

0607E0O

20302.00

20303.00

20276.00

0608E0O

NIA

04327.00

20304.0O

2030_0O

2030E0O

203_7.0O

2030&0O

20309.00

06449.00

04325.00

20310.00

20311.00

2031Z0O

2031:t00

20314.00

2031_0O

0559:_0O

2050;_00

20547.00

20503.00

20548.0O

2054_00

2031E00

20317.01

9-18335

DIESCRIPTION QTY.

4-02 x 8ram Socket Head Bolt 3

Push Button 1

Spring 1

3 x 23ram Spdng Pin 2

"n'lgger 1

2.5 x 24ram Spring Pin 2

4-0.7 x 12ram Sccl<etHead Bolt 2

Washer 5

Rear Support 1

3 x 33ram Spdng Pin l

' 4.0.7mm Fiber Nut 1

iBody 1

9.8 x 1.9mm O-Ring 1

Air Manifold 1

2g.82 x 2.62 mm G-Ring 1

TriggerSpring 1

TriggerCap 1

10.82 x 1.78mm O.Ring 1

Val_ Stem 1

2.5x 1.4ram O-Ring 2

TriggerValve Spring 1

Trigger Valve Head 1

7.5 x 1.5ram O-Ring 1

Latch 1

Lever 1

Latch Spring 1

End Cover 1

3 x 18mm Spdng Pin 1

Trip Lever 1

E-Ring 1

Nut 1

Nut Guide 1

Knob 1

Warning Label 1

Operator's Manual 1

Storage Case 1

Rebuttd Kits

Ng. 9, Nos. 3.4, 5 and B

5-- 1 20320.00 Piston-Ram Assarn_y RebuitdKit --1

F{g.9, Nos. 10, 11.12 and 14

RightFax 8/15/2003 1:18 PAGE 11/11 RightFax

_: Your Home

For repair-in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME _(1-800-469-4663)

Ca(( anyf,(ma, day or n{ght (U.S.A. and Canada)

iii!iiii_i_iii

Our Home :_:"............

For repair of carry-in items like vacuums, lawn equipment, ........_..._

':"_ and electronics, call or go on-line for the location of your nearest _

iiiii_!_!_!_i Sears Parts & Repair Center. _:ii_,_

1 800 488 1222 .........

........... Call anytime, day or night (U ,SJ_. only) :_:,_.:

www.sears.com ,_:,:::

iiii!_i_[[[i ::?:::::

•. ::>_:>:

__,_:_:_............... To purchase aprotection agreement (U.S .A.) _:::_,..,.:;..........

...............or maintenance agreement (Canada) on a product serviced by Sears: ............

:::::::: ::_::

1 800 827 6655 (u s A ) 1 800 361 6665 (Canada) ........

;:::::::: mmm == l= m ::::::

Para pedir servicio de reparacibn ..........

a domicilio ypara ordenar piezas: _.........

1"888 SU HOG_ _ ..........

iiiiiiiiiiiiiii_

_iiii:iiii:i!i!i!i!,

Au Canada pour service en franqais:

1-800-LE-FOYER _

(1-800-533-6937)

WWW.SeaPS.Ca

(1-888-784-6427)

.:::::::

ii iii;iii i!i !ii!!!iiiii!i ii i!iiii iii ii!!i!i!i!i!i!i!iii i iii !iiiii ii!i!i!i!i!i!iii i. ii !ii

®RegisteredTrademark/ru TrademarkIeu_ar_ce Mark_f Seam, RoebUckandCo.

®Mama ReglsftadeI_Mama de F_bdca/m Marc_de S_rv!dodeSears,Roebuckand Co,

_c t_ue de commerce/uoM_rquedepes_e deSea_, Roebuckmd Co. @Sears,RoebuckandCo.

Craftsman 351181720 User Manual NAILER Manuals And Guides L0308386

CRAFTSMAN Nailer Manual L0308386 CRAFTSMAN Nailer Owner's Manual, CRAFTSMAN Nailer installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation