Craftsman 351183200 User Manual NAILER Manuals And Guides L0711540

CRAFTSMAN Nailer Manual L0711540 CRAFTSMAN Nailer Owner's Manual, CRAFTSMAN Nailer installation guides

User Manual: Craftsman 351183200 351183200 CRAFTSMAN NAILER - Manuals and Guides View the owners manual for your CRAFTSMAN NAILER #351183200. Home:Tool Parts:Craftsman Parts:Craftsman NAILER Manual

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

[

SAVE

THIS MANUAL
FOR

FUTURE

REFERENCE

OWNER'S
MANUAL

MODEL NO.
351.183200

__/_/_)_/1:: RI:1FTSM I:!N
Framing Nailer

CAUTION:
READ

ALL

INSTRUCTIONS
CAREFU

LLY!

• safety instructions
• operating instructions

• replacement parts

Sold by SEARS,
Part No. 6186.00

ROEBUCK

AND CO., 3333 Beverly

Road. Hoffman

Estates,

IL 60179 _)
July 1994

DESCRIPTION
The Sears Framing Nailer d rives nails of 0 113 to 0..131"
diameter from 2 to 3 1/2" tong. Magazine is angled at
27 1/2 ° for nailing in tight spots such as when toenailing. High strength,
aluminum
components
are
lightweight and durable. Contact safety disables nailer
until nosepiece is in contact with workptece Hardened,
serrated contact tip grips wood for fast, easy nailing
Large capacity, top load magazine makes it easy to
load up 105 stick nails at a time. Nailer drives straight,
screw, and ring shank nails. The Sears Angle Framing
Nailer is exce!lent for truss making, framing, sheating,
sub-flooring and decking.,
. SPECIFICATIONS
Capacity ...............................
Nail Size ..........................

75 to 105 nails
0113 to 0.131"

Nail Lengths .............................
Operating Pressure .....................

2 to 3 I/2"
75 to 100 PSIG

Air inlet
........................
Length ...............
. .....................

1/4" FNRT
:18 3/8"

Do not operate tool if contact trip mechanism
functioning properly
Never load the tool until you are ready to use it.
Never depress tool trigger when loading.

Always load tool with nose pointing away from you and
others.
Never point the tool at yourself or others
Never carry too! with trigger depressed
Do not use oxygen, combustible gases or high pressure compressed gas as the air supply for the tool,
Always use tool at safe distance from other people in
work area.
Do not attempt to discharge fastener into hard or brittle
materials such as concrete, steel or tile.
._-Do not connect female quick-disconnect
tool side of air line

to

Do not use a hose swivel in air supply line,
Use Sears recommended

13 3/4"
5 1/8"

OPERATING

Weight ................................

8,3 lbs

AIR SUPPLY LINE

fasteners only.

INSTRUCTIONS

Refer to Figure 1.

£18351
918352

......
.........

£18353

.....

SAFETY

coupling

Connect male free-flow nipple to tool side of air line so
that tool is depressurized when disconnected
from
hose.

Height ........................................
Width ......................................

NAILS

is not

8 penny, .120" diameter x 2 1/2" long
10 penny,. 120" diameter x 3" long
16 penny, .131"diameter

x 3 1/2"long

INSTRUCTIONS

Air tool operators and all others in work area should
always wear safety goggles (must comply with ANSl
Z87.1) to prevent eye injury from fasteners and flying
debris when loading, operating or unloading this tool
Never exceed operating
kg/cm 3),,

pressure

Always disconnect tool from air supply when servicing
or adjusting toot and when tool is not in use.
Do not operate toot when nose is not in contact with
work,
/_

air

Never exceed maximum pressure.
The minimum air requirements for nailer:
Average
working SCFM, 40 at go PSI with a 3/8" air hose and
15 gallon tank
WARNING:

of 100 PSlG (7 1

Always keep hands and body away from the fastener
discharge area when air supply is connected to tool,.

J

The Sears Framing Nailer operates on compressed
at pressures from 75 to 100 PSIG.

KEEP HANDS AND BODY AWAY FROM
DISCHARGE AREA OF NAILER WHEN
CONNECTING
AIR SUPPLY. ALWAYS
DISCONNECT TOOL FROM AIR SUPPLY WHEN SERVICING,
ADJUSTING
AND WHEN TOOL IS NOT IN USE.

Clean dry air is essential to operation of Sears nailer.
Air operated tools require clean, dry, lubricated
pressed
atr to ensure
top performance,
maintenance and long life

comtow

Dirt and abrasive materials present in all air lines wilt
damage tool O-rings, valves and cylinders.

FILTEr,
- _GLIAT_2
- L_21[A'fl]_

./

/_2

FDD]
_E _HIP
g
I

FENLEDUll[
- I]IS[N,_'E[T
--J
Figure I--2--

OPERATING

INSTRUCTIONS

WARNING:

AIR SUPPLY LINE (Continued)
Moisture will reduce tool performance
removed from compressed air,

and life if not

A filter-regulatorolubricator
system is required and
shouid be located as close to tool as possible (see
Figure 1). A distance of less than t5 feet is recommended1
Keep air filter clean. A dirty filter will reduce air pressure
to nailer causing a reduction in power and efficiency
The air supply system must be able to provide air
pressure of 75 to 100 pounds per square inch at the
toot.
The lubricator
tool oil.,

(Continued)

should be filled with a non-detergent

air

All hoses and pipes in the air supply system must be
ctean and free of all moisture and foreign particles,,
Never connect a female quick-disconnect coupling to
too! side of air system A male free-flow coupling should
be connected to the tool side of air system,
The female coupling provides a seal, preventing loss of
compressed air from compressor tank when disconnected from male coupling. If connected to tool side of
air supply, the femaTe coupling could seal a compressed a!r charge in the nailer which could discharge
if the tool trigger is actuated,
The air pressure should be Properly regulated.
Different workpiece materials and different nail lengths
will require different operating pressure.

DISCONNECT TOOL FROM AIR SUPPLY. ALWAYS LOAD WITH NOSE OF
TOOL POINTING AWAY FROM YOU
AND OTHERS. ALWAYS WEAR SAFETY
GOGGLES THAT COMPLY WITH ANSI
Z87.1o

Slide pusher handle (Ref, No, 59) towards rear of tool
until it locks into position,
Insert nails into opening at top of magazine.
Hold pusher handle firmly and release by depressing
latch (Ref. No, 55). Allow pusher to gently slide forward
against nails°
_.NAILING OPERATION
WARNING:

NEVER OPERATE TOOL UNLESS CON.
TACT TRIP IS IN CONTACT
WITH
WORKpIECEo DO NOT OPERATE TOOL
WITHOUT
NAILS OR DAMAGE TO
TOOL MAY'RESULT.
NEVER FIRE
NAILS INTO THE AIR BECAUSE NAILS
MAY INJURE OPERATOR OR OTHERS
AND DAMAGE TO TOOL MAY RESULT.

The Sears Framing Nailer is equipped with a contact
trip safety mechanism that disables nailer unless contact trip is pushed against work. Hotd tooi handle firmly
and place nose of tool on location where nail is to be
applied. Pull trigger to drive nail into workpiece.

Use oniy as much air pressure as required, Using more
air pressure than needed will waste compressed air
and cause unnecessary wear to nailer.
Be sure all connections
tO prevent air Ioss,

in air supply system are sealed

LOADING
Refer to Figures 2 and 5.
NOTE: For best results use Sears nails only

Figure 2 - Loading. Fram!nq Nails

Figure 3 - Contact Trio Operation
-3-

OPERATING

INSTRUCTIONS

OPERATING

(Continued)

PRESSURE

Use only enough air pressure to perform the nailing
operation Air pressure in excess of that which is required will make the nailing operation inefficient and
may cause premature wear or damage to the tool,
Determine minimum air pressure required by driving
some test nails Into the workpiece, Set air pressure so
that test nai! heads are driven down flush with the work
surface, Nails d riven too deep may damage workpiece

Keep the magazine and nose of the natler clean and
free of any dirt, lint or abrasive particles.
The tip of the ram (Key No 11, Figure 5) can become
dented or rounded over time, Square off the tip of the
ram with a clean, fine hand file to extend the life of the
ram and naiter_ Nail firing will be more consistent if the
ram tip is kept clean and square

TROUBLESHOOTING
WARNING:

MAINTENANCE
Inspect contact trip safety mechanism daily for proper
operation.
WARNING:

DO NOT OPERATE NAILER IF SAFETY
MECHANISM
IS NOT OPERATING
PROPERLY.

Perform the
mechanism:
1.
2
3

following

procedures

to test

safety

Leave trigger untouched while pushing contact
trip into workpiece. Nailer must not fire_
Pull nailer trigger while contact trip is clear of work
and pointed away from operator and others Nailer
must not fire.
Depress and hold trigger Push contact against
work where nail is needed, The nailer should drive
only one nail each time the contact trip is pushed
against workpiece,

ff contact trip does not operate properly, repair immediately through Sears Service Center.
Replace any damaged
list to order parts..

or missing parts, Use the parts

Lubricate tool each day the tool is used with quality air
tool oil. If no air line lubricator is used, pour five to six
drops of oil into inlet (Key No 22, Figure 5) of nailer,

DISCONNECT
TOOL FROM AIR SUPPLY BEFORE ATTEMPTING REPAIR OR
ADJUSTMENT.

.....Note: Be sure tool is oiled properly. Clean and oil all
O-rings during reassembly
If too_ losers power or operates inconsistently, put five
or six drops of air tool oil into inlet cap (Key No 22).
If tool continues to operate improperly, the piston and
cylinder valve O-rings should be lubricated
with
silicone grease Remove cap, cylinder valve and piston
(Key Nos. 4, 9 and 11).
Check O-rings and replace if worn, stretched
or
damaged. Clean all O-rings and O-ring grooves with
clean, dry cloth.. Coat all O-rings and O-ring grooves
with air nailer grease or silicone grease Be careful not
to pinch or damage O-rings during assembly Assemble in reverse order of disassembly
If tool fires but nail is not discharged from magazine,
check piston O-ring (Key No, 10) Also, check all Orings in trigger valve assembly (Key Nos 35 - 45),
If tool leaks air out of nose, check cylinder O-ring (Key
No. 13) and spacer O-ring (Key No. 17)
If toot leaks air out of e×ha ust port, check cylinder valve
O-rings (Key Nos 7 and 8),

FULL ONE YEAR WARRANTY ON SEARS/CRAFTSMAN

FRAMING

NAILER

If within one full year from the date of purchase, this Sears Craftsman Framing Nailer fails due to a defect
in material or workmanship,
Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE NAILER TO THE NEAREST SEARS
STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty

gives you specific

legal rights, and you may have other fights

Sears, Roebuck and Coo, Dept, 817 WA, Hoffman Estates,

--4-

IL 60179

which vary from state to state.

NOTES

ii
___,_i
_,

1

I.,,_ It
2-.._

C

011

_Sm5

C

L,/,j

22

0

REPLACEMENT
KEY"
NO.
I

PART
NO.
I77500

PARTS LIST FOR FRAMING

DESCRIPTION

KEY
NO.

QTY,

64,0 x 25mm Bolt,
socket head*

4

2
3
4
5

1514.00
6301 B0
6302,00
6303.00

6mm Washer, split*
Rubber plug
Cap
Cap seal

4
1
t
1

6
7

6304.00
6305.00

Cylinder valve spring
Cylinder valve O-ring,
inside

1

8

6306.00

Cylinder valve O-ring,
outside

9
10

6307,00
630800

Cylinder valve
Piston O-ring

2
1
1

11
12
13
14
15

6309,,00
631000
63t 1,,00
631200
6313.00

Ram-piston assembly
Cylinder cap
Cylinder O-ring, top
Cylinder
Cylinder O-ring, bottom

1
t
t
1
1

16
17
18
19
20

6314,00
6315,00
6316_00
6317o00
631 &00

Bumper
Cylinder spacer O-ring
Cylinder spacer
Cap gasket
Nailer body

1
1
1
1
1

24
25

46-58494-3
6321.00

Inlet cap gasket
Inlet cap
5-08 x 20ram Bolt,
socket head*
5mm Washer, split
Nose O-ring*

1
I

23

6320.00
0814L00

26
27
28
29
30

6322.00
6323,00
6324,00
632500
0483,00

Cap
Bracket
Trigger

1
2
1
1
1
1

49
50
51
52
53
54
55

6162 00
6164 00
6163 00
6330 00
633100
6332 00
633300

Lever
Spring pin
Spring
Latch bracket
Latch spring
Latch bushing
Latch

I
3
1
I
1
1
1

56
57

6334.00
6088 00

1

58
59

619600
633500

Latch shaft
4-0 7 x 10ram Bolt,
socket head
4mm Washer, split
Pusher

6O
61
62
63

6336 00
6337 00
6338 00
6339,00

Plunger
O-ring
Seal

2
2
1

5 x 20mm Spring pin
5 x 12mm Spring pin
Plastic block
3-05 xl 4ram Boit,
socket head

1
4
4

6340 00
6341.00
634200
6343,00
6344.00
6345,00

3mm-0 5 Nut, fiber hex
Spring shaft
Spring spindle
Magazine spring
Spindle cover
Magazine

2
1
1

6-1 0 x 12ram Bolt,
socket head*
6-I.0 Nut, fiber hex
5-08 x 25mm Bolt,
socket head*
5mm Washer, flat*

Nose bumper
Ram guide
3 x 8mm Pin, roll
Nose
8-1,25 x 30mm Bolt,
socket head

1
1
1
1

70

634600

71
72

635400
6347,00

4

73

634800

0824.00
632600
6327.00
6328.00
6148,00

8mm Washer, split
Contact trip spring
Contact trip
Plastic shroud
Breather valve O-ring, top

4
1
1
1
1

74
75
76

634900
6350,00
6O8690

77

619800

36
37

6149o00
6150,00

Breather valve

1

78

1218 00

Breather valve O-ring,
outside

1

O-ring
O-ring
Valve
O-ring
Spring

1
1
1
1
1

79
80
81
•

6351.00
6352,00
6353,00
6! 86,00

6151.00
6152,00
6153,00
6154.00
6155,00

QTY.

615600
6157 00
615800
615900
6329 00
6161 00

3t
32
33
34
35

38
39
40
41
42

DESCRIPTION

43
44
45
46
47
48

64
65
66
67
68
69

3
3
!

PART
NO.

NAILER

2

1
1
1

2
2
1
1

6ram-0 8 Nut, fiber hex
Magazine bracket
4-0 7 x 8mm Bolt,
socket head
4ram-0 7 Nut, fiber hex

1
1

8-I 25 x 16ram Bolt,
socket head*
6ram Washer, flat
8ram Bushing
Nail wear plate
Owner's Manual

2
2
1
1
1

1
1

,. ,,,

RECOMMENDED

* Standard hardware item available locally
e Not shown.

-7-

ACCESSORIES

8 penny, .120 dia. x 2 1/2" long

918351

10 penny, .120 dia. x3" long

918352

16 penny, .131 dia x3 1/2"long

918353

J

Framing Nailer
OWNER'S
MANUAL
SERVICE

Thank you for purchasing Your Framing Nailer from Sears,
This unit will provide you with many years of reliable service
Should the, need exist for repair parts or service, simply
contact any Sears Service Center and most Sears, Roebuck
and Co stores Be s_re to provide air pertinent facts when
you call or visit The modei number of your Framing Nailer is
on the front of the nailer

MODEL NO.
351.183200

HOW TO ORDER
REPLACEMENT
PARTS

All parts listed may be ordered from any Sears Service
Center and most Sears stores If the parts you need are not
stocked locally, your order wi{I be electronically transmitted
to the Sears Repair Parts Distribution Center for handling
When ordering replacement
information:

parts, always give the following

NAME OF ITEM: Framing Nailer
MODEL NUMBER: 351,183200
PART NUMBER:
PART DESCRIPTION:

Sold by SEARS, ROEBUCK
Part No. 6186.00

AND CO., 3333 Beverly

Road. Hoffman

Estates,

IL 60179 @
June 1994



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 8
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Mon Jan 21 05:08:58 2008
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools