Craftsman 351217020 User Manual 15 PLANER Manuals And Guides L0521399

CRAFTSMAN Planer Manual L0521399 CRAFTSMAN Planer Owner's Manual, CRAFTSMAN Planer installation guides

User Manual: Craftsman 351217020 351217020 CRAFTSMAN 15 PLANER - Manuals and Guides View the owners manual for your CRAFTSMAN 15 PLANER #351217020. Home:Tool Parts:Craftsman Parts:Craftsman 15 PLANER Manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

Operator's Manual

1 5"

PLANER
Model No.
351.217020

CAUTION: Read and follow
all Safety Rules and Operating
Instructions before First Use
of this Product. Keep this
manual with tool.
Sears, Roebuck

and Co., Hoffman

www.sears.com/craftsman

21703.01 Draft (05/11/05)

Estates, IL 60179 U.S.A.

•

Warranty
....................................
SafetyRules...............................
Unpacking..................................
Assembly.................................
Installation
.................................
KnowYourPlaner.............................
Operation................................
Maintenance
.............................
Troubleshooting
.............................
PartsIllustration
andList ...................

2
2-3
3
3-4
4-5
6
6-11
11-14
15
18-23

Be alert and think clearly. Never operate power tools
when tired, intoxicated or when taking medications
that cause drowsiness.

PREPARE

WORK AREA

FOR JOB

•

Keep work area clean. Cluttered work areas invite
accidents.

•

Do not use power tools in dangerous environments.

•

Do not use power tools in damp or wet locations. Do
not expose power tools to rain.

•

Work area should be properly lighted.

•

Proper electrical receptacle should be available for
tool. Three prong plug should be plugged directly
into properly grounded, three-prong receptacle.

•

Extension cords should have a grounding prong and
the three wires of the extension cord should be of
the correct gauge.

FULL ONE YEAR WARRANTY

•

Keep visitors at a safe distance from work area.

If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears will
at its option repair or replace it free of charge. Contact
your nearest Sears Service Center (1-800-4-MY-HOME)
to arrange for product repair, or return this product to
place of purchase for replacement.

•

Keep children out of workplace. Make workshop childproof. Use padlocks, master switches or remove switch
keys to prevent any unintentional use of power tools.

If this product is used for commercial or rental purposes, this warranty will apply for 90 days from the date of
purchase.

•

Consult manual for specific maintaining and adjusting procedures.

•

Keep tool lubricated and clean for safest operation.

This warranty applies only while this product is used in
the United States.

•

Remove adjusting tools. Form habit of checking to
see that adjusting tools are removed before switching machine on.

•

Keep all parts in working order. Check to determine
that the guard or other parts will operate properly
and perform their intended function.

•

Check for damaged parts. Check for alignment of
moving parts, binding, breakage, mounting and any
other condition that may affect a tool's operation.

TOOL SHOULD

• Always unplug tool prior to inspection.

This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179

• A guard or other part that is damaged should be
properly repaired or replaced. Do not perform
makeshift repairs. (Use parts list provided to order
replacement parts.)

WARNING:
For your own safety, read all of the rules
and precautions before operating tool.
CAUTION: Always follow proper operating procedures
as defined in this manual even if you are familiar with
use of this or similar tools. Remember that being careless for even a fraction of a second can result in severe

KNOW HOW TO USE TOOL

personal injury.

BE PREPARED

FOR JOB

•

Wear proper apparel. Do not wear loose clothing,
gloves, neckties, rings, bracelets or other jewelry
which may get caught in moving parts of machine.

•

Wear protective hair covering to contain long hair.

•
•

•

BE MAINTAINED

•

Use right tool for job. Do not force tool or attachment
to do a job for which it was not designed.

•

Disconnect tool when changing blades.

• Avoid accidental start-up. Make sure that the switch
key is in the OFF position before plugging in.
•

Do not force tool. It will work most efficiently at the
rate for which it was designed.

Wear safety shoes with non-slip soles.

•

Wear safety glasses complying with United States
ANSI Z87.1. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.

Keep hands away from moving parts and cutting
surfaces.

•

Never leave tool running unattended. Turn the power
off and do not leave tool until it comes to a complete
stop.

•

Do not overreach. Keep proper footing and balance.

Wear face mask or dust mask if operation is dusty.

•

Never stand on tool. Serious injury could occur if tool is
tipped or if blade is unintentionally contacted.

•

Know your tool. Learn the tool's operation, application and specific limitations.

•

Use recommended accessories (refer to page 19).
Use of improper accessories may cause risk of
injury to persons.

•

Handle workpiece correctly. Protect hands from possible injury.

•

Turn machine off if it jams. Blade jams when it digs
too deeply into workpiece. (Motor force keeps it
stuck in the work.)
Always keep drive, cutterhead and blade guards in
place and in proper operating condition.

•
•

WARNING:
Never use highly volatile solvents. Nonflammable solvents are recommended to avoid possible
fire hazard.

WARNING:
Do not attempt assembly if parts are
missing. Use this manual to order replacement parts.

PLANER

Before planer is assembled, a suitable location should
be chosen. The planer weighs approximately 500 Ibs
when completely assembled. Planer should be assembled on location.
•

Planer needs to be set on a flat, level surface. This
improves stability, accuracy and prevents warpage
and failure of cast components and welds.

•

Make sure there is ample room on both infeed and
outfeed sides of planer for moving the workpiece
through the entire cut. There must be enough room
that neither the operators nor the bystanders will
have to stand in line with the wood while using the
tool.

•

Good lighting and correct power supply (230 volts)
are also required for a proper work area.

•

Place planer in its designated spot. Covers for
access to motor are on both front and rear sides of
stand. The planer is supplied with four lifting handles
that slide into the base on the infeed and outfeed
sides. The planer must be lifted by these handles
only and moved to the required location.

Feed work into blade or cutter against direction of
rotation.

CAUTION: Think safety! Safety is a combination of
operator common sense and alertness at all times
when tool is being used.
WARNING:
Do not attempt to operate tool until it is
completely assembled according to the instructions.

Check for shipping damage. If damage has occurred, a
claim must be filed with carrier. Check for completeness. Immediately report missing parts to dealer.

INSTALLATION

Additional parts which need to be fastened to the planer
should be located and accounted for before assembling.
Planer is shipped assembled except for the following:
two table extensions, handwheel handle, chip chute, two
roller gauge blocks, blade height gauge, roller assembly,
two roller brackets, floor leveling feet and hardware bag.

ATTACH

Hardware bag (Part No. 23516.00) includes:

•

Required parts and hardware:
Foot (4)
10-1.5mm Hex Nut (4)

•

Remove access covers (Key No. 53).

•
•
•
•
•
•
•
•

8-1.25 x 25mm Socket Head Bolt (4)
8-1.25 x 12mm Socket Head Bolt (3)
8mm Flat Washer (7)
8mm LockWasher (4)
6-1.0 x 12mm Socket Head Bolt (4)
6-1.0 x 12mm Hex Head Bolt (3)
6mm Flat Washer (6)
6-1.0mm Hex Nut (3)

IMPORTANT: Table, table rollers and cutterhead are
coated with a protectant. To ensure proper fit and operation, remove coating. Coating is easily removed with
mild solvents, such as mineral spirits, and a soft cloth.
Use caution when cleaning the cutterhead, as the
blades are very sharp. Avoid getting solution on paint or
any of the rubber or plastic parts. Solvents may deteriorate these finishes. Use soap and water on paint, plastic or rubber components. After cleaning, cover all
exposed surfaces with a light coating of oil. Paste wax
is recommended for table top.

LEVELING

FEET

Refer to Figure 21, page 22.

• Attach foot assemblies (Key Nos. 57 and 60) to the
cabinet (Key No. 52).
•

With planer in position, check table surface lengthwise and crosswise with machinist level. Check that
all four corners are supported. Adjust foot as needed
and secure in position with hex nut.

•

Replace access covers.

MOUNT HEIGHT ADJUSTMENT
HANDWHEEL
HANDLE
Refer to Figure 20, page 20.
•
•

Required parts: Handle
Thread handle into handwheel.

•

Tighten hex nut to secure handle.

MOUNT

CHIP CHUTE

•

Required parts and hardware:
Chip Chute
6-1.0 x 12mm Hex Head Bolt (3)
6mm Flat Washer (6)
6-1.0mm Hex Nut (3)
8-1.25 x 12mm Socket Head Bolt (3)
8mm Flat Washer (3)

•

Secure chip chute to chipbreaker cover using three
hex head bolts, six flat washers and three hex nuts.

•

Secure chip chute to roller case (Key No. 1) using
three socket head bolts and three flat washers.

REAR RETURN

Repeat above steps for the outfeed extension.

SOURCE

The motor is designed for operation on the voltage and
frequency specified. Normal loads will be handled safely on voltages not more than 10% above or below specified voltage. Running the unit on voltages which are not
within range may cause overheating and motor burnout.
Heavy loads require that voltage at motor terminals be
no less than the voltage specified on nameplate.

ROLLER

GROUNDING

Required parts and hardware:
Roller Assembly
Roller Bracket (2)
6-1.0 x 12mm Socket Head Bolt (4)

•

Insert one end of roller assembly (Key No. 56) into
bracket attached in previous step.

•

Insert the other end of roller assembly into remaining
bracket and attach to roller case.

Check with a qualified electrician if grounding instructions are not understood or if in doubt as to whether the
tool is properly grounded.
This tool is equipped with an approved 3-conductor
cord rated up to 250V for your protection against shock
hazards.

MOUNT TABLE EXTENSIONS

Do not remove or alter grounding conductor in any
manner. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for electrical shock.

Refer to Figure 1.
Required hardware:
8-1.25 x 25mm Socket Head Bolt (4)
8mm Flat Washer (4)
8mm Lock Washer (4)

Inspect tool cords periodically, and if damaged, have
repaired by an authorized service facility.

•

Mount table extension to planer table on the infeed
side using four 8-1.25 x 25mm socket head bolts, flat
washers and lock washers. Do not tighten bolts completely.
• Place long straight edge across table and table
extension.

Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric
cord or plug is necessary, do not connect the green (or
green and yellow) wire to a live terminal.
WARNING: This work should be performed by a
qualified electrician.

EXTENSION
•

I
Adjustment
Figure

I - MountTable

•
•

CORDS

The use of any extension cord will cause some drop
in voltage and loss of power.
Wires of the extension cord must be of sufficient size
to carry the current and maintain adequate voltage.
Use the table to determine the minimum wire size
(A.W.G.) extension cord.

Set Screw
Extensions

INSTRUCTIONS

WARNING: Improper connection of equipment
grounding conductor can result in the risk of electrical
shock. Equipment should be grounded while in use to
protect operator from electrical shock.

• Attach one roller bracket(Key No. 55) to rollercase
(Key No. 1) using two socket head bolts (Key No. 58).

•

Tighten bolts to secure extension.

•

WARNING: Do not connect planer to the power
source until all assembly steps have been completed.

Refer to Figure 20, page 20.
•

•

POWER

Position chip chute on chipbreaker cover (Key No. 52)
so that the slots on chip chute and chipbreaker cover
are aligned and slots on chip chute and holes on the
roller case are aligned.

MOUNT

Use mallet to tap extension table flush with table.

• Adjust set screws and socket head bolts (located at
outside edge of table extension) so that the table
extension is at the same height and angle as the table.

Refer to Figure 20, page 20.

Adjustment
Socket Head Bolt

•

Use only 3-wire extension cords having 3-prong
grounding type plugs and 3-pole receptacles.

•

If the extension cord is worn, cut, or damaged in any
way, replace it immediately.

EXTENSION CORD LENGTH
Wire Size

A.W.G.

Up to 50 ft ..................................

NOTE: Using extension cords over 50 ft. long is not
recommended.

Install an approved plug onto the line cord. Connect to
a matching outlet that has been properly installed and
grounded in accordance with all local codes and ordinances.
•

MOTOR
The planer is assembled with motor and wiring
installed. The 230 Volt AC capacitor start motor has the
following specifications:
Horsepower .................................
Voltage ...................................

3
230

Amperes .................................
Hertz .....................................

16.5
60

Phase ..................................
RPM ....................................

ELECTRICAL

Single
3450

CONNECTIONS

Refer to Figure 2.
WARNING: All electrical connections must be performed by a qualified electrician. Make sure unit is off
and disconnected from power source while motor is
mounted, connected, reconnected or anytime wiring is
inspected.
Planer has an approved 230 volt three-conductor line
cord and a 230 volt magnetic contactor that is prewired
in the factory (See Figure 2).

The tool has a key lock switch to prevent unauthorized use. Turn key lock switch to OFF and remove
key when tool is not in use.

NOTE: The motor will not start if the key is in the OFF
position
•

Connect planer to a supply circuit protected by a 30
AMP circuit breaker or time delay fuse.

OVERLOAD

PROTECTION

The magnetic contactor has overload protection that
helps to prevent damage to the motor. The overload
protection will automatically turn off the magnetic contactor when an overload occurs. Set thermal overload to
22 Amps. Be sure to disconnect planer from power
source when resetting overload protector. The protection is reset by opening the contactor box and pressing
the reset button.

CHECK

CONNECTIONS

Refer to Figure 3.
•

Plug in the line cord to a 230 volt power source.

•

Turn the key to ON.

•

Turn and release the stop button.

•

Depress the start button. The motor must rotate
counterclockwise facing shaft end.

•

Depress the stop button. The motor must stop.

•

Depressing the start button with either the stop
button pressed down or the key in OFF position
must not start the motor.

•

If any of the above steps do not work properly, disconnect planer from power source and recheck the
connections.

230 Line Voltage

To Motor
Figure

2 - Magnetic

Contactor

Wiring

Schematic

Figure

3 - Power

Controls

/
3

1 Column

8 Stop Button

2 Table Rollers
3 Extension Table
4 Stand

9 Lifting Handle
10 Table Locking Knobs
11 Feed Rate Shift Handle

5 Thickness Scale

12 Gearbox
13 Handwheel

6 Key
7 Start Button

14 Return Rollers

SPECIFICATIONS
Table Size ............................
Table with Extensions ....................

DESCRIPTION

15 x 173/4"
15 x 42"

Blade Width ...............................

15"

Craftsman 15" Planer is a heavy duty cast iron unit that
can plane lumber up to 15" wide and 8" thick. Planer
has a 3.15" diameter, 3-blade cutterhead with jack
screws for easy blade adjustment and replacement.
Cutterhead and feed rollers travel on precision ground
steel columns. Lumber can be fed at 16 or 25 feet per
minute and can be cut up to '/J' deep per pass.

Cuts per Minute ..........................

15,000

Planer comes with totally enclosed welded plate steel
cabinet, 4" port for dust collection and safety electrical
control with magnetic contactor. Includes 3 HP motor.

Weight ................................

Refer to Figures 4-12, and 21.

Maximum Cut ..........................

76" Deep

Floor Space ...........................

32 x 40"

Dust collection port ...................
Motor ..........................
Overall Dimensions (D x W x H)........

4" Diameter
3 HP, 3450 RPM
42 x 30 x 44"
502 Ibs

Planing refers to the sizing of lumber to a desired thickness while creating a level surface parallel to the opposite size of the board. Depth of cut is the term used to
indicate how deep the blades will cut into the workpiece.

OPERATION

SAFETY

RULES

WARNING: Operation of any power tool can result in
foreign objects being thrown into eyes which can result
in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing power tool operation.
CAUTION: Always observe the following safety
precautions:
•

Know general power tool safety. Make sure all
precautions are understood (See pages 2, 3 and 7).

• Whenever adjusting or replacing any parts on planer,
turn switch off and remove plug from power source.
•

Make sure the cutterhead and chipbreaker covers
are properly attached and securely fastened.

•

Make sure all moving parts are free from interference.

• Always wear eye protection or face shield.
•

Make sure blades are aligned and properly attached
to cutterhead.

•

Do not plug in planer unless switch is in OFF position. After turning switch on, allow planer to come to
full speed before operating.

•

Keep hands clear of all moving parts.

•

Do not force cut. Slowing or stalling will overheat
motor. Allow automatic feed to function properly.

•

Use quality lumber. Blades last longer and cuts are
smoother with good quality wood.

•

Do not perform planing operations on material shorter than 18", narrower than 3/4",or less than 'tZ' thick.

•

Never make planing operation on material wider than
15" or cut deeper than W'

DEPTH

OF CUT

Refer to Figures 4 and 20, page 20.
The depth of cut is adjusted by the relative positioning
of the table with respect to the blades in the cutterhead.
Table can be raised or lowered using the handwheel. To
adjust depth of cut:
• Loosen table lock knobs.
• Turn handwheel to raise or lower the handwheel.
•

Position the table at the desired position.

• Turn the planer key to ON position and press the
start button.
•

Feed the lumber from the infeed side.

•

Use the scale on the column to measure the depth
of cut.

• To increase depth of cut raise the table: to decrease
depth of cut lower the table.
• Tighten the table lock knobs.
• When planing several pieces of wood, plane all the
lumber with the same set-up to have uniform thickness removed.
Recommended
Hard/Softwood

Maximum

• Always keep cutterhead and blade guards in proper
working condition.
Maintain the proper relationships of infeed and outfeed table surfaces and cutterhead blade path.
• Do not back the work toward the infeed table.

Depth of Cut:

up to 15" wide ...............

0.125"

Lock
Knobs

•

• Support the workpiece adequately at all times during
operation; maintain control of the workpiece.
• Take precautions against kickback. Do not permit
anyone to stand or cross in line of cutterhead's rotation. Kickback or thrown debris will travel in this
direction.
• Turn switch off and disconnect power whenever planer is not in use.
•

Replace or sharpen blades as they become damaged
or dull.

•

Keep planer maintained. Follow maintenance
instructions (See pages 11-14).

Figure

USING

4 - Depth

of Cut

DIGITAL

SCALE

Refer to Figure 5, page 8.
•

Before using scale, wipe down the vertical scale with
a dry, soft cloth. Do not use cleaning solutions. Do
not allow any liquids (such as machine oil) to contact
the body of the digital display. Keep the device clean.

•

Data from the digital scale can be input into a computer via the port at the side of the device. Simply
slide off the small port cover (see Figure 5, page 8).

MM/INCH
•

- Millimeters/Inches

Pressing this button toggles back and forth between
standard and metric, and can be done at any time
without affecting saved settings.

HOLD - Maintains Data On The Display
• Press this button to "freeze" a measurement on the
display; it will remain even if the table is moved.
Press HOLD again and it returns to normal
measurements.
SET - Preset

Battery

•

Press SET; the indicator will flash "SET". Press and
hold the SET button and each digit flashes in turn.
When the digit you want flashes, release the SET
button.

•

Press SET button once (no longer than one {1}
second) and that digit will increase by one each time
SET is pressed. When finished, press and hold SET
button until indicator "SET" flashes, then press SET
again (no longer than one {1} second). The indicator
"SET" disappears and the value you just input is
displayed on the screen.

•

From this point on, any table movement will be
based off this setting. The setting will be kept in the
device's memory, even when the digital display is
turned off.

Cover

Figure 5 - Functions of the Digital Scale
•

This scale uses a 1.55 volt battery cell (SR44). tf it
needs replacing, slide off the battery cover and
insert the battery, with the positive pole of the battery facing out.

TOL - Tolerance

NOTE: After replacing a battery, the digital display settings should be recalibrated.

BUTTON

- Power and Zero Setting

•

Press ON/OFF/ZERO button no longer than three (3)
seconds to power on.

•

Press ON/OFF/ZERO button at least three (3)
seconds to shut off the digital display.

•

While in relative mode, press ON/OFF/ZERO (no
longer than three (3) seconds to set current position
as relative zero point.

•

While in absolute mode, press ON/OFF/ZERO (no
longer than three (3) seconds to set current position
as absolute zero point.

ABS - Relative/Absolute

Modes

•

The scale is in absolute mode as soon as power is
turned on, and displays absolute zero. Moving the
planer table up and down begins absolute measurement. Absolute measurement is usually set based
upon the distance from cutterhead to table.

•

Press ABS button (no longer than three {3} seconds)
to switch to relative mode. "INC" will appear on the
display. The value shown is in relative mode. Moving
the table up and down will now display relative
measurement.

Setting

•

Press TOL and an up-arrow indicator will appear, as
well as a flashing "SET" indicator. You can now
change the upper tolerance limit.

•

Hold down the TOL button and each digit flashes in
turn. When the digit you want flashes, release the
TOL button.

•

Press TOL button once (no longer than one {1}
second) and that digit will increase each time TOL is
pressed.

•

When finished, press and hold TOL button until
indicator "SET" flashes. While indicator "SET" is
flashing, press SET button to change the arrow to
the down-arrow indicator. You can now change the
lower tolerance limit in the same manner as you
changed the upper tolerance limit.

•

When finished setting the lower tolerance limit,
while indicator "SET" is flashing, press SET button
(no longer than one {1} second). The device is now
in tolerance measuring mode. When the up-arrow
indicator is displayed, it means the measured value
is beyond the upper limit. When the down-arrow
indicator is displayed, the measured value is below
the lower limit. When the display shows an "OK"
indicator, the measured value is within tolerance.

FUNCTIONS

ON/OFF/ZERO

a Value

ESTABLISH

ABSOLUTE

ZERO

•

Turn on the digital display. It turns on in absolute
mode.

•

Plane one side of a scrap board at an appropriate
and safe cutting depth (_/_0"for example).

•

Raise the table by the same amount (_/_6"),then turn
the board over and plane the other side. Do not
move the table from the current position.

•

Measure the planed board carefully with calipers.
This measurement of the finished board is the equivalent of the distance from table to blade.

•

Input the measurement on the calipers into the digital display. Refer to the instructions above involving
the SET button function to input this number into
your digital display.

USING RELATIVE
•

•

MEASUREMENT

•

(Key Nos. 37 and 38) and remove chip chute (Key
No. 54).
Loosen and remove socket head bolts and washers
(Key Nos. 37 and 38) and remove chipbreaker cover
(Key No. 52).
Loosen five gib screws (Key No. 7) on the cutterhead
to loosen the cutterhead gib (Key No. 6).

Blade

Screw

Height

Leg
k

Gauge

Screw

MODE

The absolute setting, for which you should have
already established the zero point, give the thickness
of your finished board after cutting (distance from
table to cutterhead).
The relative measurement mode is useful for measuring only the amount of stock that you wish to
remove (i.e., depth of cut), and eliminates having to
add or subtract to find the proper setting. It is especially helpful when planing many boards to the same
thickness.

Here is an example using relative measurement:
•

To produce even surface on a workpiece, the blade
edges must be the same distance from axis of cutterhead. The blade height comes adjusted from the factory
and should not require any adjustment. However, if
adjustments are required:
• Loosen and remove hex head bolts and washers

You have planed a board at a setting of 1" at
absolute measurement. Do not move the table from
this position. You wish to increase the depth of cut on
the next run by 0.032".
Press ABS button to start relative measurement

Gib
Figure

6 - Blade

Height

"-Blade
Adjustment

•

Position the blade height gauge assembly (Key No.
8) on the cutterhead so that both the legs of the
gauge rest firmly on the cutterhead.

•

The blade edge must just make contact with the tab
on the blade height gauge. Adjust blade height by
turning the jack screw (Key No. 4).

mode ("INC" will appear on the display).
•

Follow the previous instructions on using the SET
button function. You would input zeros for all digits,
thus establishing zero setting for relative measurement mode.

•

After setting relative zero, bring the table up until the
digital display reads "0.32" inches in relative measurement mode. You can now plane your board with
exact results. Of course, you can now toggle back
and forth between relative and absolute mode (by
pressing ABS button) and get both stock thickness
and depth of cut readings at the same time.

ADJUSTING

BLADE

HEIGHT

Figure 7 - Checking Blade Height
•

Repeat the previous two steps to adjust the blade
height on the other end of the blade.

•

Secure blade and gib by tightening gib screws.
Tighten outside gib screws first, and then, working
towards center, tighten the remaining gib screws.

•

Repeat the above steps for remaining blades.
Securely tighten all gib screws.

•

Replace chip deflector plate.

•

Replace cutterhead cover.

•

Replace chip chute.

Refer to Figures 6, 7 and 20, page 20.
CAUTION:
Planer blades are very sharp. Use leather
gloves to protect hands from injury and exercise caution
when adjusting blades.
WARNING:
Disconnect planer from power source
before adjusting planer.

PREPARING

•

THE WORK

board into the planer.

• Do not plane dirty boards. Dirt and small stones are
abrasive and will wear the blade.
•

•

Remove nails and staples to avoid damaging the
blades.

• Avoid knots. Heavy crossgrain makes knots hard.
Also knots can come loose and jam the blade.
•

•

Push slightly on board and allow automatic feed to
take the board. Release board and allow automatic
feed to function properly. Do not push or pull on
workpiece.

CAUTION:
Do not stand directly in line with front or
rear of planer. When an object is projected from planer
it will travel in this direction.

The planer works best when the lumber has at least
one flat surface. Use a surface planer or jointer to
define a flat surface.
Twisted or severely warped boards can jam the
planer. Rip lumber in half to reduce the magnitude
of the warp.

FEEDING

Rest the board end on infeed table and direct the

WORK

Feed work along the grain direction. Wood fed
against the grain will result in chipped and splintered
edges. Sometimes grain will switch direction in the
middle of a length of board. If possible, cut board
before planing (See Figure 8).

•

Move to the side and receive the planed lumber by
grasping it in the same manner in which it was fed.

•

Do not grasp any portion of the board which has not
gone past the outfeed roller.

•

Repeat this operation on all boards which need to be
the same thickness or adjust the height.

•

The planer has return rollers on the top so an
assistant can pass work back to the operator.

NOTE: An assistant must follow the same precautions
as the operator.

CUTTING

DEPTH

Refer to Figure 9.
With

The surface finish the planer provides will be smoother
if a shallower depth of cut is used. Deep cuts require
more power and cause greater wear on all machine
parts.

the Grain

Rotation

Against

the Grain
Shallow

Rotation

Grain._._,_

Cut

_<._Grain

Figure 9 - Cutting

Depth

SNIPE
Snipe is a depression at either end of the board,
caused by an uneven force on the cutterhead when
work is entering or leaving the planer.
Snipe will occur when boards are not supported
properly. A slight snipe may still be noticed when the
board is supported.

I
I

Figure 8 - Direction of Grain

An uneven force is created when only one feed roller is
in contact with work at the beginning or end of cut.

CAUTION: Do not plane a board which is less than
18" long. The force of the cut could split the board and
cause a kickback.
•

Turn the planer on.

•

Stand on the side of the planer to which the height
adjustment handwheel is attached.

•

Lift the work to infeed table by grasping edges at
approximately the middle of the length.

•

Boards longer than 36" should have additional support from free standing material stands (See
Recommended Accessories, page 19).

The snipe is more apparent when deeper cuts are
being taken.
To reduce snipe:
•

Gently, lift the board slightly when the board is fed
until the outfeed roller comes in contact with the
board.

•

Release the board when both infeed and outfeed
rollers are in contact with the board, and the board is
being fed.
Move to the outfeed side.

•

Gently lift and support the board when all of the
board has left the infeed roller.

FEED ROLLER
ADJUSTMENT

•

When planing more than one board, butt the boards
together to reduce snipe.

Refer to Figures 12 and 20, page 20.

POWER

Infeed and outfeed rollers (Key Nos. 18 and 30) feed
the workpiece under the cutterhead.

FEED RATE ADJUSTMENT

Spring-loaded feed rollers press against workpiece to
prevent rollers from slipping.

Refer to Figures 10 and 11.
Feed rate refers to rate at which wood is passed over
blades. The Craftsman 15" Planer is supplied with a
power feed system that automatically feeds the wood
into the planer under the cutterhead.

The spring tension on feed rollers must be sufficient
enough to prevent rollers from slipping on workpiece,
but tension must not be so great that rollers cause
damage to the workpiece.

The power feed system uses a 2 speed gearbox for
planing both hard and soft woods.
Low speed - 16 FPM (feet per minute) is for hard
wood, and high speed - 25 FPM is for soft wood.
•

Adjust power feed rate while planer is running.

•

To engage power feed at low speed (16 FPM), pull
engagement knob out away from planer (See Figure
11).

•

To engage high speed (25 FPM), push engagement
knob in all the way, towards planer (See Figure 11 ).

•

The power feed system can be disengaged by placing the engagement knob in the middle or neutral
position (See Figure 11).

SPRING TENSION

•

If feed rollers slip on workpiece, spring tension must
be increased (clockwise).

•

If workpiece is damaged by the feed rollers, the
spring tension must be decreased (counterclockwise).

• Adjust the spring tension on the feed rollers by rotating the adjustment screws (Key No. 21) at each end
of the rollers.
•

Be sure to adjust screws so that the spring tension is
equal on each side of the roller.

•

Holes in the center of the adjustment screws are
used to lubricate the infeed and outfeed rollers.

NOTE: Only change feed rate while the machine is running.

Shift Knob

Figure 12 - Roller Spring Tension

Figure 10 - Power Feed Shift Knob

WARNING:
Make certain that the unit is disconnected
from power source before servicing blades.

CHECKING

25 FPM
0 FPM
16 FPM

11 - Power

Feed

Rate

BLADES

•

The condition of the blades will affect the precision
of the cut. To check the condition of the blades,
observe the quality of cut which planer produces.

•

Dull blades will tear, rather than sever wood fibers,
and produce a fuzzy appearance.

• A raised grain will occur when dull blades pound on
wood that has a varying density.
• A raised edge will be produced where the blades
have been nicked.

',
Figure

FOR WORN

Adjustment

REMOVING

AND REPLACING

BLADES

LUBRICATION

Refer to Figure 20, page 20.

Refer to Figure 19, page 18.

CAUTION:
Planer blades are extremely sharp. Use
leather gloves and exercise caution when replacing
blades.

The planer gearbox has been filled with lubricating oil at
the factory. The gearbox oil should be changed each
2500 hours of operation. To change oil:

WARNING:

Disconnect planer from power source.

If the blades have been chipped or damaged, they must
be replaced. To replace blades:

•

Remove chain cover and guards (Key Nos. 44 and
47).

•

Remove chip chute (Key No 54).

•

Remove chipbreaker cover (Key No. 52)

Drain old gearbox oil by removing plug (Key No. 27)
at bottom of gearbox.

•

Loosen gib screws (Key No. 7).

•

Replace drain plug.

•

Carefully remove blade.

•

Remove fill plug (Key No. 16) at top of gearbox.

•

Thoroughly clean cutterhead slots, gibs, and gib
screws.

•

Fill gearbox with 50 or 60 weight gear oil (approximately 12 oz.).

•

Insert new or sharpened blades in cutterhead.

•

Fill until oil level is up to center of sight glass.

•

Replace gib.

•

Replace fill plug.

•

Secure blade by tightening gib screws. See
"Adjusting Blade Height" page 9.

•

Frequently lubricate all chains, leadscrews and
handwheel gears with industrial grease.

•

Repeat the previous steps for the other blades.

•

Frequently lubricate all table and return rollers,
columns and bushings using SAE-30.

SHARPENING

BLADES

ANTI-KICKBACK

The blades can be honed individually by whetting them
with fine sharpening stone. Make sure oilstone is flat and
is not worn. To sharpen blades:
• Remove blades as described above.
•

Partially cover stone with paper to protect the table
top.

•

Position infeed table so stone will contact blade along
its beveled surface.

•

Refer to Figure 20, page 20.
The anti-kickback pawls (Key No. 46) prevent the workpiece from kicking back against the direction of feed.
The pawls must rotate freely to ensure safe operation of
the planer.
•

Inspect the anti-kickback pawls daily for proper operation checking that the pawls rotate freely.

Stroke the stone across blade from one side to other

•

while stone is also moving slightly in the direction of
feed.

Clean the pawls of all gum and chips as required to
ensure safe operation.

TABLE ROLLER

Make sure to do the same amount of strokes on each
blade.

The table rollers (Key No. 2) are free-spinning rollers
that help reduce friction, making the planing operation
smoother.
The proper height of the table rollers is dependent upon
the hardness and surface finish of the workpiece:

NOTE: Many shops do not have capabilities to resurface
blades. Yellow pages should list "Sharpening Services" or
"Tool Grinding".

ADJUSTING

•

The roller height should be adjusted so that the
workpiece feeds smoothly through the planer but is
not damaged by the table rollers or by the feed
rollers.

•

Rough cut wood requires the rollers to be adjusted a
little higher, while smooth finish wood requires the
rollers to be a little lower.

•

For all workpiece materials and finishes the table
rollers should be positioned slightly above the table.

BELT TENSION

Refer to Figures 20 and 21, pages 20 and 22.
WARNING:

Disconnect planer from power source.

Belt tension must be checked periodically. To check:
Remove pulley cover (Figure 20, Key No. 34).

• Adjust belt tension by pivoting motor mounting plate
(Figure 21, Key No. 56). Pivot plate by loosening hex
nuts on tension bolt (Figure 21, Key No. 60) as
required.
•

•

ADJUSTMENT

Refer to Figures 13, 14 and 21, pages 13 and 22.

If the blades are nicked they must be replaced or
reground. Never install unbalanced blades. Always
sharpen blades in sets of four.

•

PAWLS

WARNING:

Belt is properly tensioned when slight pressure
between thumb and index finger causes _/,"deflection
of belt.
Be sure to replace pulley cover.

Disconnect planer from power source.

•

Table roller height is adjusted by loosening set
screws (Key No. 5) and rotating eccentric adjusters
(Key No. 4).

•

Use roller gauge blocks provided to check roller
adjustment.

•

Roller gauge blades are marked with three height
settings - 0.15mm (0.005"), 0.30mm (0.010") and
0.45mm (0.015").

•

Place a gauge block at each end of the roller with
the height setting desired facing upward.

•

Turn the adjuster until roller just touches gauge block.

k_ 2 "€'4

1/2=¢,

Figure 15 - Adjustment

OUTFEED

1'/2m_
_=

Block

ROLLER

HEIGHT

ADJUSTMENT

Refer to Figures 15, 16, 20 and 21, pages 20 and 22.
Figure 13 - Using Gauge Blocks to Set Roller Height

•

The outfeed roller (Figure 20, Key No. 30) is set at the
factory so that the outfeed roller is positioned 0.020"
below the blade. The outfeed roller should need no

Be sure that both ends of the table rollers are at the
same height so that the rollers are parallel with the
table and secure eccentric adjusters with set screws.

further adjustment but can be checked and adjusted
using the following procedures:

• Always adjust front and rear rollers to the same height.

WARNING:

Disconnect planer from power source.

• Adjust blade height properly (See "Adjusting Blade
Height", page 9).
•

Figure 14 -Table Roller Adjustment

Place adjustment block (Figure 15) under cutterhead
at one end as shown in Figure 16. Place 0.020" feeler gauge between block and blade. Raise or lower
table so that blade just contacts feeler gauge when
blade is at lowest position. Put gearbox in neutral and
rotate cutterhead slowly to determine lowest position
of blade. Lock table in position by tightening lock
knobs (Figure 21, Key No. 9). Do not unlock table
position until both sides of outfeed roller have been
adjusted.
r ...........................................................................

ADJUSTMENT

_Outfeed

BLOCK

Refer to Figure 15.
Some of the maintenance adjustments require the use
of a handmade adjustment block (See Figure 15).
Make this block out of hard wood scrap with the
dimensions shown. Exact dimensions are not critical but
a very smooth, level finish across the top is required.

Feeler

Gauge

Roller

Figure 16 - Cutterhead with Block

•

Remove feeler gauge and slide adjustment block
under outfeed roller. Outfeed roller should just contact adjustment block, tf outfeed roller is too high or
low loosen hex nut on set screw (Figure 20, Key
Nos. 24 and 25) under outfeed roller. Rotate set
screw to position outfeed roller properly. Secure position by tightening hex nut on set screw.

•

Place adjustment block on other end of outfeed roller
and repeat step above. Be sure that outfeed roller is
at the same height on both ends so that the roller is
parallel with the table.

CHIPBREAKER

ADJUSTMENT

ADJUSTING

Refer to Figures 15, 16, 17, 20 and 21, pages 13, 14,
20 and 22.

Refer to Figures 15, 18 and 21, pages 13, 14 and 22.
The table is positioned parallel to the cutterhead at the
factory and should need no further adjustment. If the
planer is cutting one side of the workpiece deeper than
the other producing a tapered cut, then the table may
need to be adjusted. Check to see that the blades are
adjusted properly, see "Adjusting Blade Height" page 9.

The chipbreaker breaks the chips of wood that are
created by the blades during the planing operation. The
chipbreaker then directs the chips around cutterhead
and out of the chip chute. The chipbreaker must be
positioned 0.004" below cutterhead to operate properly.
The chipbreaker position is checked and adjusted by
using the following procedure:
WARNING:

WARNING:

Chipbreaker

Disconnect planer from power source.

•

Place adjustment block (See Figure 15) on table at
outside edge of roller case and on infeed side of
planer. Slide block to one corner of roller case. Raise
or lower table until block just contacts roller case.
Lock table in position by tightening lock knobs (Key
No. 9). Do not unlock table position until all four corners of the roller case have been checked.

•

Slide block to other side of roller case on infeed side

Disconnect planer from power source.

• Adjust blade height properly (See "Adjusting Blade
Height", page 9).
• Place adjustment block (See Figure 15) under cutterhead at one end as shown in Figure 16. Place
0.004" feeler gauge between block and blade. Raise
or lower table so that blade just contacts feeler
gauge when blade is at lowest position. Put gearbox
in neutral and rotate cutterhead slowly to determine
lowest position of blade. Lock table in position by
tightening lock knobs (Figure 21, Key No. 9). Do not
unlock table position until both sides of chipbreaker
have been adjusted.
• Remove feeler gauge and slide adjustment block
under chipbreaker (See Figure 17). Chipbreaker
should just contact adjustment block. If chipbreaker
is too high or too low, loosen hex nut on set screw
above chipbreaker. Rotate set screw to position chipbreaker properly. Secure position by tightening hex
nut on set screw.

Figure 17-

TABLE POSITION

of table. Check to see that the block just contacts the
roller case.
•

Move adjustment block to outfeed side of table and
check height of both sides of roller case. Adjustment
block should just contact roller case. If all four corners of roller case are at the same height, then roller
case and cutterhead are parallel to the table.

•

If roller case is not parallel to the table, then the
table must be adjusted. Loosen the two bolts holding
the chain tension sprocket (See Figure 18). tt may
be necessary to remove bolt "A" to release the
tension in the chain.

with Block
Remove

Place adjustment block on other end of chipbreaker
and repeat previous step. Be sure that chipbreaker is
at the same height on both ends so that the chipbreaker is parallel with the table.

INFEED

ROLLER

HEIGHT

Figure 18 - Chain Tension Bracket

The table height is adjusted by removing the chain from
the corner sprockets and rotating the sprockets.
Determine which corner or corners, need adjustment
and remove the chain from the sprocket in that corner.
Rotate the sprocket by hand to adjust the table height
(be sure to leave other sprockets untouched).

ADJUSTMENT

•

The infeed roller is set 0.004" below the cutterhead.

•

If an adjustment to the infeed roller is necessary,
adjust in the same manner as described above for
outfeed roller and chipbreaker.

this Bolt "A"

NOTE: Be careful not to rotate each sprocket more
than 1 or 2 teeth.
Rotate sprocket (or sprockets) until table is parallel to
roller case. Assemble chain tension sprocket carefully
and tension chain properly.

CORRECTIVE

ACTION

SYMPTOM

POSSIBLE

Planer does not start

1 .Key is in the OFF position

1.Turn key to ON position

2.No power to planer

2. Have a qualified electrician check power
source

3.Motor overload protection tripped

3. Reset motor overload protection,
see "Overload Protection", page 5
4. Have a qualified electrician check the
switches and wiring

CAUSE(S)

4.Defective or loose switch or wiring

Frequent opening of fuses or
circuit breakers

1.Motor overloaded

1. Reduce load on motor

2.Fuses or circuit breakers do not
have sufficient capacity
3.Circuit overloaded

2. Have correct fuses or circuit breakers
installed

4.Motor wired incorrectly

3. Reduce circuit load (turn off other appliances)
4. Rewire motor using the schematic on the
motor for high voltage

Cutterhead turns in the
opposite direction

Motor wired incorrectly

Rewire motor using the schematic on the
motor for motor rotation

Excessive snipe
(gouging at end of board)

1.Dull blades

1. Replace or sharpen blades per instructions,
see "Maintenance", page 11

2.Inadequate support of long boards
3.Uneven feed roller pressure

2. Support long boards
3. Check feed roller operation

4.Cutter casting not aligned
5.Lumber not butted properly

4. Check position of elevation screws
5. Butt end to end each piece of stock as
boards pass through planer

6.Support rollers misaligned

6.Adjust support rollers

Fuzzy grain

Planing wood with high moisture
content

Remove high moisture content from wood
by drying

Torn grain

1 .Too heavy of a cut
2.Blades cutting against grain

1. Review "Depth of Cut", page 7
2. Review "Feeding Work", page 10

3.Dull blades

3. Replace or sharpen blades per instructions,
see "Maintenance", page 11

1 .Dull blades

1. Replace or sharpen blades per instructions,
see "Maintenance", page 11

2.Too heavy of a cut
3.Moisture content too high

2. Review "Depth of Cut", page 7
3. Dry the wood or use dried wood

Uneven depth of cut
(tapered cut)

Cutterhead not parallel with table

Adjust table, see "Adjusting Table Position",
page 14

Belts slipping

Loose belts

Tension belts, see "Adjusting Belt Tension",
page 12

Flashing digits on scale

Low voltage

Replace battery

Locked digits on scale

Haphazard memory

Take battery out, wait thirty seconds, then
re-insert it

No display

1 .Poor contact of battery
2.Low voltage

1. Improve battery contact
2. Replace battery

Displays only '0000'

Short-circuit of zero setting spring
and slider signal source

Remove frame and adjust spring

Function buttons won't work

Distortion of springs from
over-pressing

Remove frame and adjust springs

Rough raised grain

NOTES

Model 351.217020
Figure

19 - Replacement

Parts Illustration

for Gearbox
46

5
32

18
12

19
3

31
33

27
30
29

KEY
NO.

PART NO.

DESCRIPTION

STD852008

8mm Lock Washer*

Oil Seal

STD835045

8-1.25 x 45mm Hex Head Bolt*

6204LL Ball Bearing*

16476,00

Drain Plug

Helical Gear

STD833025

6-1.0 x 25mm Hex Head Bolt*

6-1.0 x 25mm Socket Head Bolt (LH)

23455,00

Clutch

00652.00

6mm Flat Washer (W)

23456.00

Clutch Handle

05790.00

6-1.0 x 15mm Pan Head Screw

STD843812

8-1.25mm Hex Nut*

STD315215

6201LL Ball Bearing*

STD852006

6mm Lock Washer*

23446,00

Spur Gear

23338,00

9 x 1,8mm O-Ring

23447,00

Gear and Shaft

23457,00

Knob

07322,00

5 x 5 x 12mm Key

04565,00

5 x 25mm Spring Pin

23448.00

Spur Gear

23458.00

Gasket

03839.00

Gear Case

23449.00

15
16

PART NO.

DESCRIPTION

23444.00

Gearbox

23321.00

25x40x7mm

STD315245

23445,00

23323,00

6
7

QTY.

5 x 5 x 10mm Key
Double Geared Shaft

23459.00

23460.00

Spacer

23328,00

11,8 x 2.65 Oil Seal

STD870612

6-1.0 x 12mm Socket Head Bolt*

16476,00

Fill Plug

23461,00

Chain Tension Assembly

23450,00

Double Spur Gear

23462,00

Chain

23451.00

Dust Cap

23463.00

Sprocket

23452.00

Dust Cap

STD833020

6-1.0 x 20mm Hex Head Bolt*

23332.00

5x5x64mmKey

23807.00

Drive Cover with Label

07339,00

6mm Steel Ball

STD851006

6mm Flat Washer*

23453,00

Spring

2380800

Knob

23454,00

Gear Shaft

2170&01

Operator's manual

23335.00

25 x 47 x 7mm Oil Seal

Standard

Not Shown

hardware

item available

locally

Recommended
A
A

Support Stand
Ro er Tabe

Accessories
9-21417
9-22242

Model 351.217020
Figure 20 - Replacement

Parts Illustration

for Rollercase

55
37

l
o

9 \

55_'__
59

5_5

52
49

48 3i

\
34

69 31

17
18
6

33
53

\
27

KEY
NO.

KEY

PART NO.

DESCRIPTION

N/A

Rollercase

00394.00

8-1.25

23467.00

QTY.

with Label

NO.

PART

NO.

DESCRIPTION

QTY.

STD851006

6mm

Flat Washer*

STD833012

6-1.0

x 12mm

Hex Head

Bolt*

Cutterhead

01882.00

5-0.8

x 12mm

Hex Head

Bolt

02614.00

Jack Screw

STD851008

8ram

Flat Washer*

23468.00

Blade

STD870510

5-0.8

x 10mm

23469.00

Gib

STD851003

3mm

Flat Washer*

23353.00

Gib Screw

STD863206

3-0.5

x 6mm

23470.00

Blade

Gauge

23491.00

Spacer

STD870812

8-1.25

x 12mm

23492.00

Anti-Kickback

Pawl Shaft

23471.00

61804ZZ

23490.00

Anti-Kickback

Pawl

23472.00

Spacer

23487.00

Roller Assembly

STD315255

6205LL

STD870625

6-1.0

23473.00

6x6x50mmKey

23506.00

Spacer

23474.00

Pulley

05110.00

6-1.0

23475.00

Collar

22359.00

6-1.0 x 10mm Washer

00351.00

6-1.0

x 10mm

23494.00

Chip

23476.00

Motor

Pulley

23495.00

Seal

18
19

23477.00
23478.00

Infeed

Roller

23496.00

Chip

Bushing

23497.00

Roller

23479.00

Spring

23488.00

Roller Assembly

23480.00

Set Screw

23500.00

Handwheel

23481.00

Bracket

STD870612

6-1.0

x 12mm

STD835020

8-1.25

23498.00

Crank

Case

01640.00

6-1.0

23499.00

Worm

Shaft

STD840610

6-1.0mm

06101.00

6-1.0

x 50mm

16992.00

5 x 5 x 16mm

STD315215

6201LL

23482.00

Chip Breaker

01531.00

4x4xl0mmKey

STD851005

5mm

00062.00

3BMI-32

23483.00

Bracket

23501.00

Bushing

23484.00

Outfeed

23502.00

Handle

31
32

00652.00
23485.00

6mm

23503.00

Digital

23504.00

V-Belt

23486.00

Chip Breaker

23505.00

Sprocket

23489.00

Belt Guard

23764.00

Chip

05383.00

5-0.8

23765.00

Spring

23507.00

Belt Pulley

23766.00

Spacer

x 15mm

Standard

N/A

Not available

hardware

Assembly
Socket

Head

Bolt

Bearing

Ball Bearing*

x 20mm
x 16mm

Set Screw

Hex Head

Bolt*

Set Screw

Hex Nut*
Key

Flat Washer*

Roller

Flat Washer

Chip Breaker

Set Screw

(W)

Shaft
Shaft
Cover

x 16mm

with Label

Hex head

Guard

item available

as replacement

Bolt

locally

part

Socket

Head

Bolt*

2
4

Pan Head

Screw*

2
50
1
48
1

x 25mm

Socket

Head

x 20mm

Set Screw

Bolt*

3
3

Breaker

Cover

Head Screw
with Label

9
1
2

Chute

with Label

Bracket

Socket

Head

Bolt*

6
1
1

Socket

Head

Ball Bearing*

Retaining

Bolt*

3
1
1

Ring

1
1

Assembly
Scale

1
1
2
2

Deflector

Plate

3
2

Model 351.217020
Figure 21 - Replacement

Parts Illustration

for Base

43
25

/
44
45

47
30

53J_,"
46

KEY
NO. PART NO.
1

KEY
DESCRIPTION

23404.00

Table

23405.00

Table

STD315215

6201LL

23406.00

Eccentric

00316.00

8-1.25

NO.

PART NO.

DESCRIPTION

STD870512
STD870825

5-0.8

8-1.25

x 25mm
x 25mm

QTY.

Roller

QTY.

x 12mm

STD835025

8-1.25

23424.00

Chain Tension

23425.00

Stud

Nut

STD852005

5mm

Shaft

Ball Bearing*
Adjuster

x 12ram

Set Screw

Socket

Head

Socket

Bolt*

Head

Hex Head

Bolt*

Bracket

4
4
2
1
1

Lock Washer*

23407.00

Quick

23408.00

Threaded

23426.00

Switch

23409.00

Lock Bushing

23427.00

Chain

23410.00
STD870620

Knob

23428.00

Lifting

16128.00
23429.00

5-0.8

23430.00

Contactor

01474.00

5mm Serrated

STD840508

5-0.8mm

23431.00

Emergency

STD851006

6mm

Flat Washer*

Button

23432.00
N/A

Start

Cabinet

23434.00

Cover

STD870612

6-1.0

23435.00

Pivot Bar

23436.00

Motor

Screw

23437.00

Rubber

Nut

23438.00

Collar

59
60

23439.00
STD841015

10-1.5

9
10

6-1.0

Lock

x 20mm

Socket

Head

Bolt*

1
1
Bar

x 20mm

Hex Head

Bolt

Contactor

2
1

23411.00

Table

Extension

STD852008

8mm

Lock Washer*

STD870820

8-1.25

14
15

STD851008
23412.00

8mm

STD870510

5-0.8

x 10mm

Socket

01640.00

6-1.0

x 16mm

Set Screw

23413.00

Base

00394.00

10-1.5

23414.00

Column

21
22

23415.00
23416.00

Crank
Lead

Screw

23417.00

Crank

Lead

23418.00

Lead

Screw

23419.00

Power

STD851005

5mm

23420.00

Bushing

STD851010

10mm

Flat Washer*

08342.00

4x4x12mmKey

STD835040

8-1.25

x 40mm

Hex Head

Bolt*

STD835055

8-1.25

x 55mm

Hex Head

Bolt*

x 20mm

Socket

Head

Bolt*

Flat Washer*

Bracket

x 12mm

Case

Set Screw

Column

Cord
Flat Washer*

23421.00

Gear

30
31

23422.00
STD315525

Snap

18365.00

3BMI-32

STD840812

8-1.25mm

23423.00

Sprocket

Standard

N/A

Not available

Ring

6002LL

hardware

Head

Ball Bearing*
Retaining

Ring

Hex Nut*

item available

as replacement

Bolt*

Box

1
12
1

Socket

Head

Bolt*

12
1

Mounting

Plate

Foot

4
1

x 150mm

10-1.5mm

23440.00

Retaining

23441.00

Motor

23317.00

8x8x45mm

Strain

23442.00
23443.00

Stop Button

x 12mm

locally

Hex Nut*

part

1
Washer

Hex Head

Bolt

Hex Nut*

Ring

2
10
4

2
1

Relief

Line Cord

Key

1
3
1

® Registered

Trademark

Service

Mark of Sears,

Roebuck

and Co.

® Marca Registrada / TM Marca de F_brica / s_ Marea de Servicio de Sears, Roebuck
MC Marque de commerce / MD Marque d_pos_e de Sears, Roebuck and Co.

Roebuck

and Co.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Tue Aug 14 23:55:29 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 351217020 User Manual 15 PLANER Manuals And Guides L0521399

CRAFTSMAN Planer Manual L0521399 CRAFTSMAN Planer Owner's Manual, CRAFTSMAN Planer installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation