Craftsman 358798141 User Manual SEARS WEEDWACKER Manuals And Guides L0809175

CRAFTSMAN Line Trimmers/Weedwackers, Gas Manual L0809175 CRAFTSMAN Line Trimmers/Weedwackers, Gas Owner's Manual, CRAFTSMAN Line Trimmers/Weedwackers, Gas installation guides

User Manual: Craftsman 358798141 358798141 CRAFTSMAN SEARS WEEDWACKER - Manuals and Guides View the owners manual for your CRAFTSMAN SEARS WEEDWACKER #358798141. Home:Lawn & Garden Parts:Craftsman Parts:358798141 Craftsman Grass trimmer (weed wacker) Manual

Open the PDF directly: View PDF .
Page Count: 28

operator's

manual

MODEL NO.

358.798141-28,0ce

AWARNING:

ReadtheOperator'sManual

and Follow All Warnings

and Safety Instructions.

FailureToDo So CanResuIt

in SeriousInjm-y.

•Always Wear Eye Protection During Operation

,_E/A/,qS[I:RRFT$MRN®_

GAS WEEDWACKER ®

2 Cycle Engine

* Assembly

•Operation

Fuel Mix 16:1

*Maintenance

•Repair Parts

um i ilnf11 if iiii

Sold by Sears, Roebuck and Co., Chk:ago, Ill. 60684 U.S.A.

iii iiii ,i, i_11 , ,i,,,i,,i

66909-2-16987-1-17387 @Sears, Roebuck and Co., 1987

_: TWO YEAR LIMITI_ WARRANTY ON CRAFISMAN WEEDWACKgR®

ForTwo years fromdateofpurchase, when_Weedwacker_is mainlained,luhricated,andtunedup_.eordingtotheoperating _,_

annmamtenaw.e mstmclaons mtlae operators manual, Sears will repair free of charge any defect in material or worlmmnship.

This warrantyexcludes nylon line,spark plug,and air cleaner ;which are expendable parts and [_come wornduringnor- ._

IfthisWeedwacker _ isused forco_ial or rental purposes, thiswarranty appliesfor only 30 days from the date ofpurchase.

WARRANTY SERVICEiS AVAILABLE BYCOI'_--TING THE NE_ SEARS SERVICE CENTER/DEPARTMENT

IN THE UNITED STATES. This w_rranty appli_ only while this productis in use in the United States.

This warrantygives youspecific legal rights, andyou may also have other rightswhich vary from stateto state.

_SEARS, ROEBUCK AND CO_DEF£ 6981731A SEARS TOWERCHICAGO, IL 60684

TABLE OF CONTENTS

WARNINGS AND SAFEFY INSTRUCTIONS ......... 3

KNOW YOUR TIRJMMER .......................... 6

ASSEMBLY "7

ENGINE INFORMATION ............... •........... 9

A. Fueling Your Engine ' ,9

B. Pre-Operation Cheeks ........................ 10

C. Starting Instructions .......................... t0

D. Operating Instructions ........................ i I

USING YOUR TRIMMER .......................... 11

A. Trimmer Safety . 12

B. Trimmer Line Advance ....................... 12

C, Cutting Methods ............................ 13

GENERAL MAINTENANCE ...................... 14

A. Maintenance Safety .......................... 14

B. Trimmer Head .............................. 14

C. Carburetor Adjusm_ents ....................... 16

D. Air Filter .................................. 17

E. Starter Rope ................................ 18

E Drive Shaft Lubrication .................. : .... 19

G. Trouble Shooting Chart ....................... 20

REPAIR PAKrlS LIST ............................. 2 I

ACCESSORIE_ .................................... 25

A.TTACHMEN'IS ................................. 25

QUICK REFERENCE PAGE ....................... 27

ENGINE TYPE:

DISPLACE'MENT:

ENGINE RPM:

IGNITION:

CARBURETOR:

ENGINE "OFF":

STARTER:

MUFFLER:

_CLUTCH:

FUEL TANK:

SPARK PLUG:

SPARK PLUG GAP:

MODULE AIR GAP:

LL_RICATION:

CUTTING LINE:

SHAFT LENGTH:

SPECIFICATIONS

2-Cycle, Air-Cooled

28,0c0

Operating-- 6500- 7500

Idle- 2800 -3200

SolidS_

Diaphragm All Positions with.

adjustable _el mixture jets

PushButton

Auto Rewind

Lo Tone _.California approved

spark arresting

Centrifugal

16,9ft, oz_

STD361258

.025"

,010"/,014"

Gasoline/Oil Mixture- 16:1

(See "Fueling Your Engine")

.080 " Diameter, monofilament

'41"

DRIVE SHAFT HOUSING

SAFETY INSTRUCTIONS

MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S.

PATENTS: 3,'/0g.967; 3,826,068; 3,859.776: 4,035,912; 4.052.789: 4.054,992:

4,067. log; 4.104,797:4.114.269; 4,124.938:4,1.56,312;4.156,967; 4,161,820:

4,167.812; 4.269,372; 4.269,675; DES.249.630; DF,S,_$5.764: DES.260.394.

U.S. AND FOREIGN PATENTS PENDING.

STARTER ROPE

HANDLE

TRIMMERI_FA_

2,.AIR FILTER

VARNINGS AND SAFETY INSTRUCTIONS

_WARNING -- _PO_8 I00£ CANBEOANGESOU$!

This tool can cause serious injury or blindness to the operator and others. The warnings and safety instructions inthis manual

must be followed to provide reasonable safety and efficiency in using this tool. The operator is responsible for foIlowing the

warnings and instructions in this manual and on the tool. Read the entire Operator's Manual before assembling and using

this tool! Restrict the use ofthis power tool to persons who read, tmderstan d, and follow the warnings and instructions

in this manual and on tl_ tool.

THROWN

_k DANGER

NEVER USE BLADES WITH THIS TOOL.

-- THE BLADE CAN COME OFF AND

SERIOUSLY INJURE YOU AND OTHERS.

-- THIS TOOLIS DESIGNED FOR

LINE TRIMMER USE ONLY.

AWARNING

THE TRIMMER LINE CAN THROW OBJECTS

VIOLENTLY.

-- YOU CAN BE BLINDED OR INJURED.

-- WEAR EYE AND LEG PROTECTION.

WARNING

HAZARD ZONE FOR THROWN OBJECTS.

• -- THE TRIMMER LINE CAN THROW

OBJECTS VIOLENTLY.

-- OTHERS CAN BE BLINDED OR

INJURED. •

-- KEEP PEOPLEAND ANIMALS

OPERATOR'S_

AW_G ,

READ OPERATOR'S MANUAL.

-- FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

/_/ - r_ILU.ETOoOSOCANRESULTIN

.,.,':° iTURNP_:> ".-

/."

WARNINGSAND SAFETY

1. Always wear asafety face shield or goggles. See

"_,ccessories."

2. Always wear heavy, long pants, boots and gloves. Do

not wear loose clothing, jewelry, short pants, sandals

or go barefoot. Secure hair so it is above shoulder

length.

3. Do not operate this tool when you are tired, ill or under

the influence of ateohol, drugs or medication.

4. Always use the assist handle. See "%ssembly:'

5. Wear hearing protection if you use this tool for more

than 1½ hours perday.

6. Never start or run the engine inside a closed room or

building. Breathing exhaust fumes can kill.

7. Keep handles free ofoil and fuel.

A700£$AFETY

1. Inspect the entire tool before each use. Replace

damaged parts. Check for fuel leaks and make sure all

fasteners are in place and securely fastened.

2. Replace trimmer head parts that are cracked, chipped

or damaged in any way before using the t_x)l.

3. Useonly Sears flexible, non-metallic, monofdament,

cutting line of the correct diameter. Never use wire,

rope, string, etc.

4. Be sure the shield is properly attached.

5. Use only the specified trimmer head. See "Specifica-

tions:' Make sure the trimmer head is properly installed

and fastened. See "'Assembly:"

6. Besure the trimmer head stops turningwhen engine

idles. See "Carburetor Adjustments"

7. Mal_ carburetor adjustments with the drive shaft

housing supported to prevent the trimmer line from

contacting any object.Hold the tool by hand. Do not

use the optional shoulder strap for support.

8. Keep others away when making carburetor adjustments.

9. Useonly accessories or attachments recommended-

for this tool by Sears.

AF LSAFE

1. Mix and pour fuel outdoors and where there are no

sparks or flames.

2. Use a container approved for fuel.

3. Do not smokeor allow smoking near fuel orthe tool or

while using the tool.

4. Wipe up all fuel spills before starting engine.

5. Move at least 10feet away from fueling sitebefore start-

ing engine.

6. Stop engine before removing fuel cap.

7, Emptythe fuel tartk before storing thetool, ltis recom-

mended that the fuel be emptied after each use. If fuel

is left in the tank, store so fuel will not leak.

8. Store tool and fuel in an area where fuel vapors cannot

reach sparksor open flames from water heaters, elec-

tric motors or switches, furnaces, etc.

INSTRUCTIONS

A ar/T G "

.Inspect the area to be cut before each use. Remove

objects (rocks, broken _lass, nails, wire, string, etc.)

which can be thrown or become entangled in the trim-

mer head.

2. Keep others including children, animals, bystanders

and helpers outside the 60 foot Hazard Zone. Stop the

engine immediately if you are approached.

3. Always keep the engine on the right side ofyour body.

4. Hold the tool firmly with both hands.

5. Keep firm footing and balance. Do not over-reach.

6, Keep the trimmer head belowwaist level.

Z Do not raise the engine above your waist. The trimmer

head can come dangerously close to your body.

8. Keep all parts of your body away from the trimmer head

and muffler when the engine is running.

9. Use only for jobs expla!ned in this manual.

1. Maintain the tool according to recommended pro-

cedui'es. Keep the trimmer line at the proper length.

2. Disconnect the spark plug before performing mainte-

nance except for carburetor adjustments.

3. Make carburetor adjustments with the drive shaft hous-

ing supported to prevent the trimmer line from con-

tacting any object.'Hold the tool by hand. Do not use

the optional shoulder strap for support.

4. Keepothersaway whenmakingcarburetoradjustments.

5. Useonly genuine, replacementparts as recommended

bySears.

A. TSANSP0J GAND STORAG£.

1. Hand carry the t0ol with the engine stopped, and the

muffler away from your body.

2. Allow the engine to cool, empty the fuel tank. and

secure the tool before storing or transporting in a

vehicle.

3. Empty the fuel tank before storing the tool. It is recom-

mended that the fuel be emptied after each use. If fuel

is left in the tank, store so fuel will not leak.

4. Store the tool so the line lirniter cannot accidentally

cause injury. The tool can be hung by the drive shaft

housing.

5. Store tool out of reach of children.

If situations occur which are not covered in this manual,

use care and goodjudgment. Contact your Sears Service

Center if you needassistance. 5

III III I I IIII II I II IIIII IIIll I] I IIII .IIIIIIIIII II

r_o w YOUR TRIMMER

it iiiiiitlttt lit I tit it t tl It ttl I t

A. INTRODUCTION

YourTrimmer is aversatile product developed for large KEY

lawnsand to make shortwork ofa-cariety of lawn care tasks NO.

-- trimming, scalping, mowing, and sweeping. 1

Special Features Include: 2

• Antivibe assist handle 3

•Semi-automatic line feed head 4

•18" cutting path 5

• Easily Coverts to aPower Blower, Edger orMini- 6

Od/ivator with the special series of optionalinter- --

changeable attacinnents. See the '_l_achrnent"

section for more details.

B. UNPACKING INSTRUCTIONS

I. Remove contents from the carton if you have not

done so_

2. Check parts against the list below.

3. Examine parts for damage. Do not use damaged parts.

4. Notify your Sears Store immediately_tf apart is miss-

ing or damaged.

NOTE: It isnormal to hear the fuel filter rattle inan empty

fuel tank.

CARTON CONTENTS: QTY.

Engine 1

Drive Shaft/Boring Assembly w/Safety Label I

Shield 1

Trirmner Head 1

•Assist Handle 1

8-oz. Can -2 Cycle, Engine Oil I

Operator's Manual (not shown) 1

Loose Bag Parts ( not shown) 1

* LOOSE PARTS BAG CONTENTS:

7 Flex Shaft Lube 1

8Bearing Housing Screw 4

9 Large Cup Washer, Trimmer Head 1

10 Flex Bolt, Assist Handle t

I I Flat Washer, Assist Handle 1

12 Knob, Assist Handle 1

* These hardware parts are Grade 5 or better. Do not substitute

lower grade parts. Always use genuine replacement parts as

recommended by Sears.

SAFETY LABEL

STATE AND LOCAL ORDINANCE REQUIREMEN_

Yourengine is equipped witha temperature limiting muffler and spark arresting screen which meets the requirements of California

Codes 4442 and 4443 and the requirements of all U.S. Forest Land and the statesof Maine, Oregon, and _shington.

Check with your state and local authorities for regulations pertaining to Temperature Limiting Muffierand Spark Arresting

requirements. Ifyou operate this tool ina state or locale where such regulations mist, you are legally responsible for maintaining

the operating condition of these parts. Failure to do so is a violation of the law.

g,r,,,i

IHII[II[IIIVJIJII I III I II I IIIIII I . IIII

,m,l,Wll,_llUll

A.QQi_.]Iu[IIll .V _t°°l is received assembled, repeat all steps in this'section to be sure assembly is correct

•,.v-...-...,,--.., and is adjusted for the Ol_mtor.)

iiii IIIIIIIIII ii I iiiiiiiiiiii iiiii i iii IIII i iiiiiiiiiiiiiiiii

A. PREPARATION

•This Operator's Manual has been developed to help you

assemble the tool and to provide its safe operation. It is

important that you read the entire manual to become

familiar with the tool before you begin assembly.

1. READ YOUR OPERATOR'S MANUAL

Iltli_tlltlllIII IIIIIIII Ill[ IIIHIIIIImHI i

B. ASSEMBLY STEPS

2. Tools you Will need:

a. Small Phillips Screwdriver

b. Flathead Screwdriver

c. Needle-nose Pliers

d. Tape Measure & Grease Pencil

e. Wrenches: 3/8 inch, 7/16 inch or

Adjustable wrench

"ii

IlililIliilllllI I I I I

1. SHIELD _Figure 1

AWAR mG

Failure to install the shield in the position shown in Ytgm-e

I can result in serious injury to the operator. The shield

must be centered under the b_ housing clamp with

the widest part of the shield directed toward the engine.

_ [CAI/TION: ] The line limiter is sharp and can

Cut you.

a. Align the Stfield on the Bearing Housing with the

Shield centered under the Bearing Housing Clamp

with the widest part of the shield directed toward the

engine. Figure 1.Align screw openings.

b. Insert the four Bearing Housing Screws through the

Bearing Housing and the Shield.

c. Tighten each Screw evenly and securely with a

wrench or flathead screwdriver.

:2.TR/MMER HEAD -- Figure 2 &3

a. Remove the packing cover from the Arbor Shaft.

b. Place the Large Cup Washer on the Arbor Shaft. Fit

the center opening ofthe Washer around the shoulder

of the Dust Cup. Mal_ sure the Washer is against and

curved over the Dust Cup. Figure 2.

c. Threadthe TnmmerHeadclockwise _ ontothe

Arbor Shaft.

tL4_RDWARESHOWNACTUALSIZE

BEARING

WIDESTPART

OFSItIELD

HOUSING

i i iiii ii iii i._

d. Line up the hole in the Dust Cup with the hole in the

Bearing Housing by turning the Dust Cup. Figure 3.

e. Insert the Phillips screwdriver into the aligned holes

to keep the Arbor Shaft from turning. Figure 3.

f. Tighten the Trimmer Head against the Dust Cup

while holding the Phillips screwdriver.

g. Remove the Phillips screwdriver.

h. Press the Tap Button and pull4 inches of line from

the Trimmer Head. Figure 3. About 2 inches ofline

can be advanced each time the Tap Button is pressed.

NOTE: To remove the Trimmer Head, insert

Phillips screwdriver into the aligned holes in the Dust

Cup and the Bearing Housing. Unthread the Trim-

mer Head counterclockwiseA, m_.

Figure 3 7

'+ 3. DRIVl_ SHAFT HOUSING _ Figure4 .+

a. Removethe packing cover from theend ofthe Drive

Shaft Housing.

,NOLO: Make sure theFlexible Drive Shafl does not

fall out of the Drive Shaft Housing when the pack-

ing cover is removed. Dirt on the shaft will

significantly reduce its life. If the Flexible Drive

Shaft falls out of the housing, reinstall.

b. Mark aline 1-1/2inches from the straight end of the

Drive Shaft Housing. Figure 4.

c. Loosen (but do not remove) the Pinch Clamp Bolt

Onthe Engine Shroud. Figure4.

d. Pull about 6 inches of the Flexible Drive Shaft from

the straight end of the Drive Shaft Housing with

needle-nose pliers.

e. Insert the end of the Flexible Drive Shaft into the

square opening inside the Engine Shroud.

f. Firmly push theDrive Shaft Housing intothe Engine

Shroud untilit bottom s out, approximately at the

1-1/2" mark. Figure 4.

g. Position.the Drive Shaft Housing as shown in Figure

h. Tighten the Pinch Clamp Bolt securely with

a wrench.+

NOTE: If the Pinch Clamp Bolt is removed, the Bolt

must be installed into the unthreaded side of the

:PinchClmn pfirst, then, into the threaded side in

order to securely attach the Drive Shaft Housing.

_1_ _ FLF_XmLEDRIVE

INSTALL SHAFI"

.PINCH CLAMP BOLT

FROM

ENGINE

MARK 1½ _

PINCH CLAMP HOUSING

+: , Ftgure4

WASHER

4.ASSIST HANDLE --Figure 5

a. Hold the Assist Handle so it is leaning back toward

theEngineand aligned betweenthe Engineandthe

Safety Label.

b. Firmly push the Assist Handle onto the Drive Shaft

Housing. Figure 5.

c. Install the Assist Handle Bolt, Washer, and Knob.

d. Tighten the Knob by hand only.

&OPERATING POSITION,- Figure 6

a. Before starting the Engine, stand as shown in

Figure 6and check for the following:

l).Left arm fully extended ,hand holding Assist

Handle.

2).Right arm slightly bent, hand holding+the Rear

" Handle, fingers onThrottle Trigger.

3) .Rear Handle below waist level.

4).Weight of tool evenly distributed between arms.

5).Without operator bending over, the Trimmer

Head is near and parallel to the ground and easily.

contacts the material to be cut.

b. Adjust the Assist Handle up or down the Drive

Shaft Housing (butabove the Safiey Label) to acom-

fortable position.

l).Loosen the Knob by hand, adjust Handle.

Retighten Knob by hand only.

2).Rotate the Handle from left to fight if it is

necessary to tilt the angle of the Trimmer Head

for cutting a large, sloped area such as a ditch

bank.

RIGHT ARM

SLIGHTLY BENT,

HANDLE, FINGERS

SAFETYFACESHIELD

REARHANDLE

BELOW

WMSTLEVEL

LEFT ARM EXTENDED,

HAND HOLDING THE

ASSIST HANDLE

if ....

*+,...

illiilliiiiillii•HimiiiiiiIIIH II II IllllllllllllIIIIII Illllllll

m,iii iiiiii illl .

ENGINE INFORMATION

a. Use only recommended fuel mixtures.

b. Mix and pour fuel outdoors and where there are

•no sparks or flames.

c. Use a container approved for fuel.

;d. Do not smoke or allow smoking near fuel or the

tool or while using the tool.

e. Wipe up all fuel spills before starting engine.

f. Move at least 10feet away from fueling site before

starting engine.

g. Stop engine before removing fuel cap.

h. Empty thefuel tank before storing the tool. It is

,recommended that the fuel tar& be emptied after •

each use. If fuel is left in tank, store so fuel will not

leak.

i. Store tool and fuel in an area where fuel vapors

cannot reach sparks or open flames from water

heaters, electric motors or switches, furnaces, etc.

2. FUEL MIXTURE

•Your tool is powered by a two-cycle engine which

requires a fuel mixture of regular unleaded

•gasoline and a high quality engine oil specially

•made far 2-cycle, air cooled engines. The internal

design of the 2-cycle engine requires lubrication of

moving parts. Lubrication is provided when the

recommended mixture of gasoline and oil is used.

Gasoline must be clean and not over two months

old. Gasoline will chemically break down and form

compounds that cause hard starting and damage in

2-cycle engines.

•The correct measure of gasoline to oil is very

important. Too much oil in the mixture will fou! the

spark plug.

]CAUTION:[ Too little oil or incorrect oil will

cause the engine to overheat and seize.

Always mix the fuel thoroughly in a container

since gasoline and oil do notreadily combine. Do not

mix gasoline and oil directly in the fuel tank.

3. USE THE FOLLOWING ONLY:

(16 parts gasoline to 1part oil)

,t.no NoTUSE:

• BIA oIL (Boating Institute of America) --

-- Does not have proper additives for air-cooled

2-cycle engines and can cause damage to your

unit. "

• AUTOMOTIVE OIL-

-Does not have proper additives for 2-cycle engines

and can cause damage.

•GASOLINECONTAINING AI_OHOL --

High Test, Premium or Gasohol (Ethanol or

Methanol)

-- Stiffenscritic'_ carburetor fuelmetering elements

and causes engine damage from overheating.

-- Increases vapor lock (causes hard starting).

Attracts water causing corrosion damage.

5.HOW TOMIX FUEL AND FILL TANK

a. Pourl/2 gallon regular unleaded gasoline into an

approved, markedconminer.Do not mix gasoline

and oil directly b7the fi_el tank.

b. Add entire measureofengine oil.

c. Cover container tightly and shake for one minute.

d. Add remainder of gasoline.

e. Cover container tightly and shake again.

f. Slowly remove fuel container cover.

g. Remove fuel cap. See "'Specifications:" for location,

h. Fill the tank using a spout or funnel.

i. Reinstall the fuel cap securely,.

I IIIIIIllllII I •i iiiiiiiiiiiiiiiiii Illt l ,HlUIlUUlII,U

B. PRE_PERATION CHECKS

_WARNING

Review all Warnings and Safety Instructions in this

manual.

Before operating your tool, always:

I. Inspect the entire tool before each use. Replace 7.

damaged parts. Check for fuel leaks and make sure all

fasteners are in place and securely fastened.

2. Replace trimmer head parts that are cracked,

chipped or damaged before using this tool. 8.

3. Use only Sears flexible, non-metallk, monof'flament 9.

trimming line of the Correct diameter. Never use

wire, rope, string, etc. 10.

4. Use only with the shield properly attached.

II I _ _ £ Illl Illllllllllll I Illlllll I Illlllllllllllllllll

€. STARTING INSTRUCTIONS (For location of controls,

Use only the specified trimmer head. See "Specifica-

tions?' Make sure the trimmer head is properly

installed and securely fastened, Refer to "Assembly"

Be sure the Wimmer head stops turning when engine

idles. See "Carburetor AdjustmentsY

Make carburetor adjustments with tbe drive shaft

housing supported to prevent the trimmer fine

from contacting any object. Hold the tool by hand.

Do not use the shoulder strap for support.

Keep others away when making carburetor

adjustments.

Use only accessories or attachments as recom-

mended by Sears for this tool.

Clean the air filter if dirty before operating the tool.

Refer to._'Specificafions,' for air filter location.

IIII I II ]111111111111111111111II I IIIIII IIIIIII[--

refer to "Specifs_tions.")

1. Before starting the engine:

a. Fuel engine. Move 10feet away from fueling site.

b. Extend line4 inches from the Trimmer Head k)pro-

vide and adequate load on the engine.

AWAmCm

The trimmer head will turn as soon as the engine starts.

c. Stand Lu the operating position. Rest Shield on

ground, supporting Trimmer Head up off ground

away from tr_s, bushes, onlookers, etc. Figure 7.

d. With optional Shoulder Strap, place Shoulder Strap

on your shoulder. Start engine before clipping

Shoulder Strap to the tool.

2. For a Cold Engine:

a. Pull Choketo full-chokeposition. Figure 8.

b. Grip rear handle and _ Throttle Trigger fully

squeezed through step "f."

•c. Pull Starter Rope sharply until engine pops or

attempts to run, but no more than 8 pulls at fi_ choke

to avoid flooding the engine. The engine "pop" or

'hltempts to run" may be hard to hear. _w operator

mustU_n carefully. After 8pulis, proceed to step

"d." even if enginehas not attempted to run.

•d. Push Choke.to half-choke position. Figure 9.

e, Pull Starter Rope sharply until engine runs, but no

more than 5 pulis,

NOFE: If engine has not starteA after 5pulls, repeat

steps "a" through "e."

f. Allow engine to nm 5 seconds, then push Choke to

no-choke position. Figure 10. Keep Trigger fully

squeezed until engine runs smoothly.

NOTE: If engine dies with Choice at no-choke

position, repeat steps "d" through "f"

AW_G

Avoid any bodily contact with the muffler on a warm

engine. A hot muffler can cause seriousburns.

3. For a Warm Engine:

a. Pull Choke to half-choke position. Figure 9.

b. Grip rear handle and keep Throttle Trigger fully

squeezed until engine runs.

e. Pull Starter Rope sharply until engine runs, but no

more than 5 pulls.

d. Push Choke to no-choke position. Figure 10.Keep

Trigger fully squeezed until engine runs smoothly.

N(II'E: If engine does not run after 5 pulls, it is

probablyflooded. Wait a few minutes and repeatpro-

cedure using no-chokeposition. Figure 10.

4. For a Warm Engine (After Running out

of IAter):

a. Refuelengine. Move 10feetaway from fueling site.

b. Pull Choke to full-choke position. Figure 8.

c. Grip rear handle and keep Throttle Trigger fully

squeezxxl until engine runs.

d. Pull Starter Rope sharply until engine pops or

attempts to run, but no more than 5 pulis.

e. Push Choke to no-choke position. Figure 10.

f. Pull StarterRope until engine rum, but no moi_than

5 pulls. Keep Trigger fully squeezed untilengine

runs smoothly.

NOTE: If engine has not started, pu!l Starter Rope

5 more pulls. If engine still does not rtm, it is pro-

bably flooded. Wait a few minutes and repeat pro-

cedure using no-choke position. Figure I0.

(

[ _G POSITION

Lo 7

1 ! FULL CHOKg. tHALFCHOKE

Figures 'igure 9

tNOCHOKE

_1 ........ _HHH,

Figure 1o

I IIIIIIHIII III 1 IIIIII I IIIIIIIIIIWII I III III IIIIIIIIIIIII 11 IIII[,,,m ii

D. OPERATING INSTRUCTIONS ."

t. Bring the engine to cutting speed before entering

the material to be cut.

L*.r

a. Do not run the engine at a higher speed than

•necessary. 1_e cutting line will cut efficiently when

the engine is run at less than full throttle. At lower

speeds, there is less engine noise and vibration. The

'trimmer line will last longer and will be less likely

to "'weld" on the spool.

b. If the Trimmer Head does not turn when the

engine is accelerated, make sure the Drive Shaft

• Housing is properly seated in the Engine Shroud.

Refer to '_ssembly-Drive Shaft Housing:'

2. Always releas e the Throttle Trigger and allow the

engine to return to idle speed when not cutting.

IIIIIII I IIIIIIIII I IIIIII

USING YOUR TRIMMER-

I IIIII IIIIIIIIIII I IIIIIII I IIII III

3. Make sure the Trimmer Head stops turning when

the Throttle Trigger is released and the engine runs

at idle speed. For correction, refer to "Carburetor

Adjustments"

4. To stop the engine:

a. Release the Throttle Trigger.

b. Push"Off" Button. HoM button down until the

engine stops. Figure 11.

Flgu¢_ 11

ii IIII ilU iiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiii

i Illllll II II _ = ,II III _ [II I I _/

AV0'ARNING " .THROW$OBJEL

The rapidly moving line causes objects to be thrown violently.

The shield will notprovidecompletepmtecfion to the operator

or others. The operator must wear a safety face sMeld or

goggles. Always wear heavy, long pants andbo0ts. Keep

others at least 30 feet away. :.

.'" f" .

AWARN•ING HAZASDZONE

This tool will throw objects and Cut. Keep others including

children, animals, bystanders and helpers at least 39 feet

away from the operator and tool. Stop the engine if yon are

approached.

Trimmer Head

#71-85764

Use Only Genuine Replacement Parts

WARNING ,- TZlM

Trimmer head parts that are chipped, cracked or damaged in

any way, can fly apart and cause serious injury. Do not use.

Replacedamaged parts before us'mg the tool.

A. _'rRIMMEIg $_

1.OF A OR

..- - a. Always wear asafety face shield or goggles. See

'_.ccessories,'

b. Always wear heavy, long pant_ boots and gloves.

Do not wear loose clothing, jewelry, shortpants, san-

dais or go barefoot. Secure hair so it is above

shoulder length.

c. Donot operatethistool whenyouare tired, ill or

under the influence of alcohol, drugs or

medication.

d. Do not swing the toolwith Such force that you are

in danger of losing your balance.

e. ever start or run the engine lnstde a dosed room

or building. Breathing exhaust fumes can kill.

f. Keep handles free of oil and fuel. •

2. TOOL

a. Inspec t the entireto01 before each use. Replace

damaged parts. Check for fuel leaks randmake sure

all fasteners are in place and securely fastened.

b. Use only Sears flexible, non-metallic, monofila-

* merit cuttingline of the correct diameter. Never

use wire, string, rope, etc.

'c. Be sure the shield is properly attached.

dlMake sure the trimmer head is properly installed

.... and securely fastened. Refer to "Assembly."

e. Be sure the trimmer head stops turning when the

":'_e idles. See "Carbu._r_r Adjustments."

I II IIII I' IIIIIIIII I I I

K_ _ ADVANCE

• The line will advance approximately 2 inches each

time the bottom of the trimmer head is tapped on the

ground with the engine running at full throttle.

•TheLnSmtefficient linelength isthe maximum length

allowed by the line limiter.

•Alwayskeepthesmeldinplacewhenthetoolisbeing

olmrated.

f. Make carburetor adjustments with the drive

shaft housing supported to prevent the trimmer

line from contacting any object. Hold the tool

with your hand. Do not use the optional shoulder

strap for support.

g. Keep others away when making carburetor

adjustments.

h. Use only accessories or attachments recom-

mended for this tool by Sears.

3._G

a. Inspect the area to be cut before each use. Remove

objects (rocks, broken glass, nails, wire, string, etc,)

which can be thrown or become entangled in the

trimmer head.

b. Ai_vays keep the engine on the right side 0fyour

body.

c. Hold the tool fLrmly with both hands.

d. Keep firm footingand balance. Do not over-reach.

e. Keep the trimmer head below _aist level.

f. Do not raise the engine above your waist.

g. Keepallp_tsofyour bodyaway from thetrim-

mer lineand muffler when the engine is running.

h. Use only forjobs ex_.Jained in this manual.

iiiiii

JJl Ill II Ill I IIIIIII IIIIII I "I'II'II'IHII

t &wamema

Useonly Sears flexible, non-metallic monofdamentcut-

tingline. Donot use other materials suchasrope, wire,

string, etc. W'we can break off during cutting and

•become a dangerous mile.

NOLO: Always tap the trimmer head on a grassy area. Tapping

on surfaces such as concrete or asphaltcan cause excessive wear

to the trimmer head.

• To advance line:

..•-

1. Operate the engine at full thi'ottle.

2. Hold trimmer headparallel to and above the grassy

ai'ea.

3. Tapthe bottom of the trimmer head lightly on the

groundonetime. See Figure 12. Approximately 2

inches of line will be advanced with each tap.

NOTE: ffthe line is worn down to two inches or

less, more than one tap will beVWxluir_ to obtain the

most efficient line length.

N_ •TOADVANCE

\ _ I LINE,

LINE LIMITER \ t I TAP BOTTOM OF

TRIMMER HEAD

Figure 12

/•.

_L - IIlllIIIII III II

i iiiiiiii

C. CUTTING METHODS

•The tip of the line does the cutting. Allow the line to

trim at its own pace. You will achieve better results by

.... not eroding the line into the cutting area. The right and

wrong way are shown in Figure/3.

• The line will easily remove grass and weeds from

around walls, fences, trees and flower beds, but it

also can cut the tender bark of trees or shrubs and scar

fenceA To help avoid damage to vegetationor trees with

tender bark, shorten line to 4-5 inches and use tess than

full throttle.

•The line will wear faster and willneedto be advanced

•more ti_uenfly whenyou are cutting against rocks,

bricks, concrete, metal fences, etc., than when cut-

ring against trees or wooden fences.

•For trimmingor scalping, use less than full throttle

to increase line life and decrease head wear.

-- during light duty cutting.

--next to rocks, bricks, concrete, metal fences, etc..

e-Formowingorsweeping, use full throttle for a good

clean job.

•Avoid letting the trimmer head continuomly contact

_the ground during normal cutting. Constant contact

will causetrimmer head damage and premature wear.

Figure 13

Always wear eye protection. Never lean over the trim-

met head. Rocksor debriscan ricochet orbethrmm into

eyes and face and cause blindness or other serious injury.

1. TRIMMING ,-. Figure 14

Hold the tap button about 3 inches above the ground and

tilt thetrimmer head atan angle. Allowthe tip oft.he line

todothe cutting. Do not force the trimmer line into the

workarea.

2. SCALPING -- Figure 15

•The scalping technique removes unwanted vegetation.

Hold the tap button about 3 inches above the ground and

tilt the trimmer head at an angle° Allow the tip of the line

to strike the ground around trees, posts, monuments,

etc. This technique increases line wear.

3. MOWING -- Figure 16

Yo_artrimmer is ideal formowing in places conventional

lawn mowers cannot reach. In the mowing position,

keep the line parallel tothe ground, Avoid pressing the

head into the ground as this _:an scalp the ground and

..damage the tool.

4. SWEEPING -- Figure 17

The fanning action of the rotating line can beused for

a quick and easy clean up. Keep the line paxallei to and

above the surfaces being swept and move the tool from

side to side.

14 Figure 16

Figure 15 Figure 17 ....

.... i3

III I III I I IIllIl II Ill III I

GENERAL MAINTENANCE

ill I iiiiiiiiiiiiiiiiiiiiiiiiii iii II IIIIIIIIII II Illll III

A. M_.JNTENANCE SAFETY

Maintain the tool accordingto recommended pro-

cedures. Keep the trimmerline at the proper length.

Disconnect the spark plug before performing

maintenance except for carburetor adjustments.

3. Makecarburetor adjustments with the driveshaft

housing supported to prevent the trimmerline

from contacting any object. Hold the tool with your

hand. Do not use the optional shoulder strap for

support.

4. Keep others away when making carburetor

adjustments.

B. TRIMMER HEAD +

•For proper line feed:

.. Use only genuine Sears pre-wound spools and

bulk line, Use of other spools or line can result in

excessive breakage, line welding and improper line

feed.

-- Pre-wound spools offer the most convenient

melhod for replacing line as well as opt_umper-

formance. Be sure to always replace thespool, ffthe

square comers of the drive lugs are rounded off,

• reduced in size or broken off. Figure23.

• • Alwaysdean dirt anddebris from thespool andhub

when performing any type maintenance.

1. Installing Spool w/Line

a. Hold the Trimmer Head as shown inFigure 18.Press

the lock tab, and turn lock ring counterclock-

• wise _.

b. Remove the lock ring, tap button, and spool. Fig-

ure 19.

c. Clean dirt and debris from all parts.

:d. Inspect all trimmer head parts. Clean and replace as

necessary. See "Spool Replacement" this section.

lAw _smsv

Trimmer head paris that are chipped, cracked or

damaged in any way can fly apart and cause serious

injury. Do not use. Replace damaged parts before

using the tool.

NOTE: After a groove is worn into one side of the aluminum

line saver, the line saver can be turned upside down and

reinstalled (with the spool removed) to provide a new wear

surface. Figures 19& 20.

&w,tmmm :

The line saver must be installed only from the inside of the

spool housing with the flanges facing toward the spool, If

installed on the outside of the spool housing, the line saver

can fly offand become a dangerous missile.

Be sure thetrimmer head stopsturning when engine

idles. See "Carburetor Adjustments:'

Use only Sears flexible, non-metallic monofilament

cutting lineofthecorrect diameter, Never use wire,

rope, string, etc.

Replace trimmer head parts that are cracked, chip-

ped or damaged in any way before using the tool.

8. Use only genuine replacement parts as recom-

mended by Sears.

9. Inspect entire tool. Replace damaged parts. Check for

fuel leaks. Make sure all fasteners are in place and

securely fastened.

i i i,, ii i ,

Figure 18

DRIVI

TAP Bt,TFON L(K'K RING _._

HOUSING

Figure 20

LINE

Figure 19

.._CATCtl

(

e. Make sure the line saver is in place and installed cor-

rectly. Insert the end ofthe line in the line saver as shown

in Figure 20. Place spool in homing. Press spool down.

"lhm and lock spool under lugs on drive gear.

f. Replacethe tap butch; press lock tab and installthelock

ring. Tumloekringcloclcwise _ and fasten under

all four catches on the housing. Figures 20 & 21.

g. Check to be sure the lock ring is properly installed by

att_,m_ting to turn thering cotmtereloekwise _ and

pulling emit. Reinstall properly ifthe leek ring comes

Off. Figure 21.

TURN LOCK RING

CLOC_ TOINSTALL

_WARNING

The lock ringmust be fastened under all four catches on

housing. If installed incorrectly, the lock ring am fly off.

FigUre Zl

h. _all on the line to change the spool from theIocked posi-

tion tothe operating position. Figure 22.

i. Obtain correct line length by pressing tap button and

pulling on the line again.

NOTE: Each time the tap button is pressed, approx-

imately 2inches ofline can be pulled from the trimmer

head. Figure 22.

"--.Spool Replacement

a. Replace the spool when the squa_ comers of the lugs

are rounded off, reduced in size, or broken off.

Figure 23.

b. To replace the spool, follow "Installing Spool wiLineY

3.Line Replacement/Repair

a. To replace the line on existing spool:

:1.)Follow "Installing Spool w/Line;' steps "a-d,' and

remove any line re_g on the spool.

2.)Use a40 foot length of Sears .080_diameter trimmer

line.

3.)Insert 1/16to 1/8 inch of the end of the Iine through

the hole in the inner rim ofthe spool. Allow no more

than 1/8 inch of line to extendbeyondtherimto avoid

interference with the drive gear.

4).Wrap the line evenly onto spool in a clockwise direc-

tion as shown by arrow on spool. Figure 24.

NOTE: Wrap line fmnly and evenly for proper

line feed.

5.)Follow "Installing Spool wtLine" steps "e--i."

b. if the line breaks off or back up in the Trimmer

:Head, follow "Installing Spool w/Line,' steps "aM:'

Pull slaekinline untilthelineis tightly _mmndon spool,

Ieaving4-6inches ofextendedIine. Continuewithsteps

"e-iY

.A2PROXIMATELY 2 INCHES OF LINE

CAN BE PULLED FROM THE TRIMMER HEAD

F_mre 22

NO!_L SPOOL

LUG

WORNSI'OOL

F mre 23

.1/8"

WRAP LINE ON SPOOL l

AS SHOWN BY ARROW. _t

•Figure2,4

I I I IIII IIIIIIIIIIIIIII III IIII IIIIII II i iUlllJmJll iillii IIIIl JIlllI II

€. CARBURETOR ADJUSTMENTS

AWARNING

Make carburetor adjustments with the drive shaft hous-

ingsupportedtopreventthetrimmer line from contact-

ing any object. Hold the tool with your hand. Do not use

the optional shoulder strap for support.

AW_G

Keep others away when making carburetor

adjustments.

Aw asm

Serious injury to the operator and others can occur if the

carburetor is not properly adjusted.

•The carburetor has been carefully adjusted at the

• factory. However, the operator must be sure that

adjustments are made when any of the following

conditions occur:

NOTE: Be sure to properly prepare the• toolas

deseribedin "1. Preparation" before making any adjust-

• ments.

-- Engine will not continue to run at idle position.

See "2. idle Speed Adjustment" and "5. Lmv

Speed Mixture Adjustment."

-- Trimmer Head continpes to spin when the engine

idles. See "2. Idle Speed Adjustment" and "4.

Deceleration Check"

-- Engine dies or hesitates when it should accelerate.

See "3. Acceleration Check"

-- Loss of cutting power which cannot be corrected by

cleaning the air filter. See "tt I_gh Speed Mixture

Adjustment"

-- Engine does not return to idle from full throttle

•within 2 s_onds. See'_4. Deceleration Check"

--Engine will not run. See "Troubling Shooting

Chart" Then, if the carburetor requires adjust-

ment, begin with "7. Basic Carburetor Settings"

•This is a complicated task and it is important to

follow instructions in sequence as indicated.

•Very Small adjustments can affect engine perfor-

mance. It is important to turn the screw a very small

amount per adjustment and test performance before

making further adjustments. Each adjustment should

be no more than the width of the slot in the adjusting

screw.

_k WAdtt_G

The trimmer line will be spinning during most of this

procedm_ Wear your protective equipment ando_e

all safety instructions.

1. PREPARA'I_ON

a. Use a fresh fuel mix. See "Fueling Your Engine"

b. Make sure the line extends to the length allowed by

the line limiter to provide correct load on engine.

C-

Start the engine. Cut grass for 3 minutes to warm

en(me. 7he engine must be at operan'ng temperature

before carburetor adjustments can be performed

correcll_

Stopengineand removeair filterby pulling itoutwith

your fingers. Refer to "Specifications" for location.

2. IDLE SPEED ADJUSTMENT

Allow engine to idle.

Adjust Idle SpeedScrew (Figure 25) until the engine

continues to run without stalling and without the

trimmer headmoving.

-- Turn screw clockwise _to increase engine

speed if the engine stalls or dies.

-- Turn screw counterclockwise &-_ to slow

engine down andiorto keep the trbnmer linefrom

turning.

c. Follow instructions in "3. Acceleration Check" and

'_,. Deceleration Check."

d. No further adjustments are necessary ifthetrim-

mer head does not turn at idle speed and if per-

formance is satisfactory.

_WARNING

Recheck idle speed after each adjustment. The trimmer

head must not turn at idle speed to avoid serious injury

to the operator and others.

3.ACCELERATION CHECK

a. Allow engine to idle.

b. Squeeze Trigger fuliy.

1.) Ifperformance is satisfactory, proceed to '4.

Deceleration Check"

2.) If the engine does not accelerate smoothly, turn

the Low Speed Mixture Screw (Figure 25)

counterclockwise _,_ asmall amount (no

more than the width of the slot in the adjusting

screw).

c. P-_eat step "'b." until smooth acceleration is

obtained.

NOTE: It may be necessary to repeat "2. Idle Speed

Adjustment" through "3. Acceleration Check" to

•obtain correct adjustments.

d. Follow instructions in "4. Deceleration Check"

\,.

4. DEmEan &TION CHECK

a. Allow engine to idle, then squeeze Throttle Trigger

fully.

b. Allow engine to run at full speed for about I second.

c. Release the Throttle Trigger to the idle position and

listen to the deceleration of the engine. It must return

to idle smoothly and within 1 to 2 seconds.

1.)Ifperfonnam:e issatisfactory, proceed to step "d:'

2. )If the engine slowly or erratically returns to idle

or idles erratically, repeat "2. Idle Speed Adjust-

ment" or continue through Low Speed Mixture and

High Speed Mixture Adjustments to obtain proper

deceleration.

d. Recheck idle speed.

&••.towsPnnMJx ,jn ADJUS

a. Allow engine to idle.

b. Tumthe Low Speed Mixture Screw 0Figme 25) slow-

:ly clockwise _ until the speed starts to drop. Note

this position.

c. Turn the Low Speed Mixture Screwcounterclockwise

until the speed increases and then stm'tsto drop

again. Note this position.

6. HIGH SPEED MIXTURE

ICAUTZON: 1Do not operate engine at full throttle for

prolonged periods while making high speed

adjustments as damage to the engine can occur.

a. Support the drive shaft housing offthe ground so the

trimmer line will not contact any object.

b. Allow engine to idle, then squeeze Throttle Trigger

fully.

NOTE. Perform steps c. through e. at fuUthrottle.

c. Turn High Speed Mixture Screw _igure 25) very

slowly clockwise _ until engine speed is reduced.

d. Turn High Speed Mixture Screw very slowly

counterclockwise _. Stop when the engine just

begins to run rough.

e. Turn the screw slowly the minimum amotmt clockwise

until the engine runs smoothly.

f. Follow instructions in "3. Acceleration Check" and 4.

Deceleration Check"

ICAUTION:I If the engine does not operate

according to these instructions after repeating the

adjusting steps, do not use the tool. Take it to your

Sears Service Center.

Set the Low SpeedMixture Screwat the mid-point bet-

ween the two positions.

Follow instructions in "3. Acceleration Check" and '_€.

Deceleration Check?'

ADJU]ksrJtErCrSCREW_ _JF/dn/"Yl i

A/1 !

L'IDLE SPEED [

_AH_GH SPEED MIXTUR E ;juSTMENT

7. nASmCAnSUnETORS rmGS

•a. Turn the Low Speed Mixture Screw and the HighSpeed

Mixture Screw (Figure 25) clockwise _ just until

they stop. Do not turn the screws until they are O'ghtas

damage to the needle seats can occur.

b. Turn the Low Speed Mixtureand High Speed Mixture

Screws one full turn counterclockwise ,i,-_.

c. Follow instruetions"l. Preparation," through "6. High

Speed Mixture Adjustment,'

8. REINSTALL AIR FILTER

Be sure filter is clean. See "_dr Filter" for instructions.

ICAUTION:[ Fit air filter into the comers of the

housing tokeep dirt from entering the engine and caus-

ing enginedamage.

ii iii HIIIIIIHI IIHII III

D. &iR FILTER

A dirty air filterdecreases the life and performance ofthe

engine and increases fuel consumption.

Clean the Air Filter:

• Always after $tanks of fuel or 5 hours of operation,

•whichever is less.

•More frequently, in dusty conditions.

1. Pull the Air Filter from the engine with you fingers.

For Air Filter location, see "Specifications:'

II 1111111111111111111111111

Wash in soap and water.

ICAUTION: I Do not clean the air filter in

gasoline or other flammable solvent to avoid

creating a fire hazard,

Squeeze dry and replace.

[¢_,UTION:I The air filter must be fitted into

the corners of the housing to avoid engine

damage. 17

E. STARTER ROPE

•This is a complicated andpotenfially hazardous task.

-It is recommended that only your Sears Service

Center perform this repair.

_WARNING

Always wear eye protection and gloves when servicing

the starter rope. The recoil sprin_ located beneath the

pulley, is under tension. If the spring flies out, serious

injury can result.

OTo repair or rephce:

1. Disconnect sparkplug wire.

2. Drain all fuel from tank.

3. Remove the four screws from fan housing. Figure 26.

4. Carefully separate fan housing from shroud about

• one (1)/inch.

5_ Disconnect fuel line from fitting. Figure 26.

6. Disconnect lead from "'off" button terminal on

ignition module. Figure 26.

7. Slide high tension lead grommet from slot in fan

housing. Figure 26.

8. Separate the fan housingcompletely from theshroud

while guiding the choke throughthe fan housing.

9. If the starter rope is not broken, release the spring

tension by pulling about 12 inches of rope from the

pulley and catch the rope in the notch as shown.

-. "Figure29. •

[¢_U_ON: [ Be sure the tension on the starter

spring is released by rotating the pulley clock-

wise _withyourfingerwhflepushingdown

on the pulley with your hand.

10. Remove screw and washer from the starter pulley

very carefully. Rotate the pulley clockwise

until no tension is felt and carefi_y lift the pulley out

of the fan housing. Figure 27. Remove old rope.

lc_moN Momaa_

N OFFBUTION

TERMINAL

HIGH TENSION LEAD

SHROI_

FUEL LINE

FUEL LINE FITTING FAN

HOUSING

rWmre

ll.

_2_

13.

14.

16.

17.

Move away from the fuel tank with the rope to be

installed. Use a match and melt both endsofthe rope

to prevent fraying.

Pull the melted ends through a thick, clean rag while

the rope is still hot to obtain smooth, pointed tips.

Insert one end of the rope through the handle and

secure with a knot.

Insert the free end ofthe rope through rope exit hole

into the inside of the fan housing.

Guide rope inside pulley, then up through the pulley

ratchet side of pulley hole to the outside by pushing

the rope through from the hole on the spring cam side

with a small Phillips screwdriver. Figure 28.

Wrap rope counterelockwise _ around pulley

ratchet and tuck loose end back under rope where it

comes out ofhole. Leave a 1/4 to 1/2 inch tail laying

fiat on the top of the pulley. The rope tail must not

extend beyond the edge of the pulley. Figure 28.

Carefully replace pulley in the housing. Be sure the

pulley isall the way down. Replace washer and screw

and tighten. Figures 27 & 28.

18. Turn the pulley clockwise _ until all the rope is

wrapped onto the pulley.

19. Putlouttheropebythehandle(approximately 12")

and hold the pulley.

PULLEY

SCREW

PULLEY II

NOIL_

.ROPE

SPITING

Ftgu_ 27

UNDERSIDE

HOLE

RATCHET

Figure 28

I, ROPE TAIL

20. Pull thel2 inch slackin the ropeintothe inside ofthe

fan housing and catch rope in pulley notch. Fig-

ure29.

21. Hold the rope taut andmake 2 complete on'as ofthe

pulley counterclockwise _ toplacetension on

the spring. Continue to hold the pulley to retain

tension.

22. Align pulley notch with rope exit hole, release

slack in the rope and pull starter handleto the full

extent of the rope. Release the pulley and slowly

a!low the rope to wind around the pulley.

23. Reverse steps tore-assemble fan housing to shroud.

NOTE: Be sure to guide choke knob through the

hole in the fan housing during re-assembly.

-- II ii tl i i H III II

E DRIVE SHAFT LUBRICATION

•Lubricate the Flexible Drive Shaft:

-- After each ten (I0) hours of operation.

-- Before operating if the unit has been stored for

: 90 days or longer.

•Use Flex Shaft Lube Part No. 30102.

NOTE: A tube of "Flex Shaft Lube" has been supplied

with your unit to be used after the fast I0 hours of

operation.

Fignlt_ 29

•Use the following procedure for best results:

AW_G

If engine hasjust beenoperated, avoid toudah_ the muf-

tier. A hot muffler can cause serious burns.

IIIII III I II 11911 I II

[CAUTION: ] Lay the Flexible Drive Shaft on a clean

surface. Avoid laying the shaft on the floor, ground or

on any surface that may have dirt or debris, Even after

wiping theshaft, grease residue can pick up dirt par-

tides that can cause damage or premature failure.

3. Check the Flexible Drive Shaft for broken wires, twists

or kinks and replace if damage is found.

ICAUTION: ] Take care to avoid injuring your hands

and f'mgers with broken wires when checking for

damageorwiping the flexible drive shaft. A cloth will

not prevent the broken wires from puncturing or tear-

ing your skin.

4. Using aclean cloth, wipe the surface of the Flexible

Drive Shaft thoroughly to remove any old grease.

Figure 31.

5. Applyaurtiformcoat oflubetotheentire surfaceofthe

Flexible Drive Shaft.

I. Loosen (but do not remove) the.Clamp Bolt and

remove the Drive Shaft Housing from the Engine

Shroud. Figure 4:

2. Remove the Flexible Drive Shaft from the Drive

ShaftHousing as shown in Figure 30.

6. Injectthe remaining contcnts ofthe tube into the top of

the Drive Shaft Housing.

Z Replace Flexible Drive Shaft in the Drive Shaft

Housing.

8. Follow theinstructions in '_Lssembly" to replace Drive

Shaft Housing into the Engine Shroud.

WIPETHE _OF

THEFLEXIBLEDRIVE SHA_Pr

Figure 30 Figure 31

19 •

G. TROUBLE SHOOTING CHAKT

TROUBLE

Engine wil! not start

or will run only for

a few seconds after

starting

Engine will not idle

properly

Engine smokes

excessively

Unit engagesat

idle speed

CAUSE

1. Fuel tank empty.

2. Engine flooded.

3. Sparkplug not fa'mg.

4. Fuel not reaching carburetor.

5, Carburetor requires adjustment.

6. None of the above.

I. Idle speed set too stow.

2. Idle speed set too high.

3, Low Speed mixture requires adjustments.

4. None of the above.

1. Air filter dirty.

2. Spark plug fouled. -:

3. Carburetor requ!res adjustment.

4. None of the above:

1, Air filter dirty.

2. Fuel mixture incorrect.

3. High speed mixture requires adjustment.

1. Fuel mixture incorrect.

2. High speed mixture set too low.

3. Spark p!ug incorrect.

4. None of the above.

1. Carburetor requires adjustment.

2. Clutch requires repair.

REMEDY

.. ...... i i ,H i i

1. Fill tank with correct fuel mixture,

2. See "Startinglnstructions"

3. Install new plug.

4. Check for dirty fuel filter; clean. Check

for kinked or split fuel linei repair or

replace,

5. See "Carburetor Adjustments,"

6. Contact your Sears Service Center, , ,,,,,, ,,,

1. Adjust idle speed screw clockwise to

increase speed.

2, Adjust idle speed screw counterclock-

wise tOreduce speed.

3. See "Carburetor Adjustments."

4,_Contact your Sears Service Center,

1, Clean or replace air filter.

2. Clean or replace spark plug and regap.

3, See "Carburetor _Ajustments"

4. Contact your Sears Service Center.

fuel mixture.

3. See "Carburetor Adjustments:'

1. See "Fueling Your Unit?'

2. See "Carburetor Adjustments?'

3. Replace with correct plug,

4. Contact yaur Sears Service Center.

I III I II II ......

1. See "Carburetor._djustments'"

2. Contact your Sears Service Center.

Clean or replace air filter.

Empty fuel tankand refuel with correct

Tri.mmerhead 1, Drive shafi broken or notengaged. I. Replace or see "Assembly3"

does not turn when 2. Carburetor requires adjustments. 2. See "Carburetor Adjustments?"

engine is accelerated 3. Clutch slipping. 3. Contact your Sears Service Center.

,,, .......................... 11,,,, ,L ......

Trim_r head 1. Drive shaft broken or not engaged. 1. Replace or See '_ssembly.

stops under a load 2. Carburetor requires adjustment. 2, See "Carburetor Adjustments."

3, Clutc h requiresrepair, 3. Contact your Sears Service Center.

1 IIIUIIIIII ......... IIIIIIIII [ I ii

Line does not advance 1. Line improperly wound onto spool. 1. Rewind spool.

2. Worn spool. 2. Replace spool,

.+._.

WEEDWACKER ®REPAIR PARTS LIST -- Model 358.798141-28.0cc

KEY PART •QTY.

NO. NO. RE(},

•t 706515 1

]r l

93896

93898

92O67

92O68

93897

7O6502

93387

92133

93846

92243

15518

93214

93886

91783

STD

5I"f007

STD

551225

STD

522510

93853

STD

541410

69O86

DESCRIPTION

_;mm.er Head Assembly 8t0ck

#7! .B5764 (inclo2-9)

IHub wiUne Saver

1_"Line Saver

1Spring

IAdaptor*Sp_ing

1Drive Gear

1 Spool w/Line-Stock #71 .,B5789

1 Reiease Button

1 Cove_

1 Shaft-Arbor

2 Screw-l14".16xl.!18" Shield

to Bearing Housing

1Screw+5tl6-Self Tapping

1 Bearing Housing Assemblp

ffncL#15, 16,17,18. 21.22 &23)

1Shield

2 Retainer-Bearing

2Screw #10-24xS/8"-Hex Hd.

Une Limiter

1 Washer-t14" IntoTooth Lock

1Screw-Pinch Clamp

Line Limiter

Nut-10-244.ocktng

1 Beadn_Js& Spacer Kit

KEY

NO.

Decals

101

SE_ImrCl_fS_N.

¢u__umwJu=Kim*

....

.q...=..q.._,,

....PART QTY. DESCRIPTION

NO. REQ,

92216 1 Washer-3!8" DustCup

92359 I DuSt Cup

92218 1 Grass Washer

92059 1 Knob-If4"-20

STD 1 Washer-ll4-Rat

551025

15737 1 Hex Bolt-l14'_-20x1-1 [2"

15561 2 Screw-Pan Hd,-#12-11x2"

24376 2 Cup-lsolato_

25985 2 Spacer Isolator

24373 2 Isolator.VtbraSon

15209 2Wa.sher-l/4 Flat

93859 1 Handte-Anti_,ibe

25986 1 Center Section-Handle

26009 1 Cushi0n-Handlo Center Section

10754 I Handle-Anti-vibeAssembly

(Incl. #29,30. 31, 32, 33.

94493 1D_ve Sltaft Housing

92261 1 Rexibte DdveShaft

30102 1Rex Shaft Lut:;e

66909 1Operator's Manual

26717 1 Decal-Anti-vibe

27430 1 Decal-,.°_fatyLabel

26574 1 Decal.Shield

SEAR s WACKER ® REPAIR PARTS UST ,--.Model 358.798141-28.0€€

34-

102

19 30

KEY PART _¥. "" KEY PART QTY. • ._ " _;

NO. No. v._ ;I. DESCRIPTION •NO, NO, REQ. DESCRIPTION

1 24436 tBumperFuelTank Housing ' 25 26048 1 StarterPulley

2 26566 1 Handle& FuelTank Housing 26 15123 1Washer#10StaxterPulleyScrew

3 27373 1 HandleCover 27 15479 1Screw-#lOx3/4".HexWasher

4 24365 1 Trigger-Throttle Head-StarterPulley

524371 1 AirFilter 30 15563* 1 Screw-#10xl-3!16"Pfastite

6 26679 1 KillSwitchButton 31 26981 1 ' FuelLineFitting•

7STD 1Screw#8-16x3t4"PanHead- 32 69247 1 LineKit

610807 HandleCover 34 11778 IShroud

8 15412 1 Washer 35 10776 1 FuelTankAssembly

9 15583 2 Screw_iO-24xl-1!2"-Sems (IncLPI6, 20,31&32)

FanHousing-Top 36 15376 2 .Screw

10 "t5407 1 Screw 37 93802 1Bolt.PinchCla_np

11 15582 2 4Screw#10,.24x518-Same 40 15168 2 Screw

FanHousing-Bottom 41 26735 1 Handle-Starter

12 24461 1 Trigger-Spring Decals

13 15357 ,e, Sorew#'10-14x,314"*FanHousing 101 27456 1 Decal-lnstructiotls

• _toHandle& FuelTank " 102 27406 1 Decal-Shroud(Right)

14 24407 1 KillSwttchSpring 103 2.7405 1 Decal.Shroud(Left)

15 24303 1 ChokeKncb

16 10729 1•_ FuelCapAssembly(Incl.O.RIng)

I8 69231 1RopeKit

19 26122 t AirBaffldSpacer

20 10897 1 FuelPick.UpAssembly

21 69178 1 Fan HoustrlgKit

22 42067 1 StarterRe_i Spdng

23 26035 1 AirBaffle

24 15544* 2 Screw.#10x3/8" Pan Hd,-

.. AirBaffle

•If,_ourunithasbeenservicedwiththemetalfan housing,usePartNo.15373(screw-#10-24xl/4-RI.Hd.),insteadof.15544(KeyNO.24),and

Part no,15305(Sorew-#!0.24xi-3/16 Rl, Hd.), insteadof 15563(KeyNo. 30) •

SEARS !

.% -VEEDWACKER ®REPAIR PARTS LIST -. Model 358.798141-28.0cc

60.. 11-[_! !_-_i

t6 5

1,i'

.23

KEY PART QTY.

NO. NO. REQ.

1 42059. 1

2 STD 1

541131

•3 15127 t

4 39114 1

5"'STD •2

5510_

6 69181 _1

7 19059 2

8 ! 536g 4.

9 10757 I

10 39103 I

1! 24435 ..1

12 26237 t

13 24558 1

14 15254 1

15 24651 1

16 15004 1

17 39082 1

18 3943 1

19 3933 t

20 STD 1

361258

21 15126

22 23373

23 24902

24 15404

25 19111

26 26581

,27 151_

28 32029

29 15351

3O 244_

31 19108

DES_iP'RON "KEY PART QTY.

NO. NO. OLEO. DESCRIPTION

Spring-Starter Dog .32 19105 1 Seat-Carburetor Case

Nut-Rywheei-(5/t6"x26)

Washer-Rywheel

•FlywheelAssembly(incl. #1)

- .Screw #8-32x3i4_-Fil. Hal.-

Ignition Module

•Kit-Ignition Module '

,_Seal-Crankcase

•Screw.Crankcase

Crankcase Ass'y. (Inc!. #7 & 28

&Qty. 4 of #8)

High Tension-Lead Assembly

(ind.#17.18 & 19)

•Grommet-Plug Wire

.Guide Plate

Choke Shutter

Wave Washer

Choke Wire Clamp

Screw

High Tension Lead Wire

Boot-Spark Plug

Connector-Spark Rug Lead

Spark Plug (CJ-14)

1Key-Flywheel

t•Boot-Throttle

1 Throttle Wire(Red)

1Screw

!"_Gasket-Cyfinde r

1 Ring-Piston

2 Retainer-Wrist Pin

2 Bearing-Ctankc_se

2 Washer-Thrust-Crankcase

1Reed Valve.

1•Gasket-Carbu retorCase to

Crankcase

33 69238 1Line Kit

34 26236 1ChokelWire

35 26029 1 Cover-Carburetor Case

36 STD 4 Scf'ew#8-18x9/16" -Pan Hd.-

610805 CarburetorCase Cover

37 SI'D 1 Screw#6.19xGf16"-P_ Hd.-

610603 Reed Valve

38 23367 1 We.sher-Reed Vatve Screw

39 15239 2 _1/4".20x_4"-Hex

Socket Hd..Cyiinder

AO 12191 1 Cylmde_r

42 24g03 2 Spring-Muffler Detachment

43 69241 1 Piston Kit(Incl. #26, 27 & Pin)

44 32092 1 Bearing_WdstRn

45 10844 1Cranksh aft& Rod Assembly (tncl,#44)

46 26046 1 Carburetor Housing

47 19115 1 _=Gasket-Carburetor

48 35183 1Carburetor-WA-149,

(See Page 24 for Assembly)

49 "15379 1 Screw-Carburetor

52 69248 1 MufflerAss'y.

53 69196 1 i_t-clufch Washes

54 69194 1 Kit-Clutch Assembly (incl.

Clutch Washer

55 24932 2 Spring-Muffler Guard

56 24855 1 Gu_ard-Muf6_r

57 10797 1 Coupling & Bearing Assam bly

58 30054 1 Sealant-Crankcase

(Not Supplied With Unit)

59 69219 1 Engine Gasket Kit

(_lndicatas Contents)

60 24158 1 Lead W_m-KillSwk'ch

* IndicatesEngineGasketKitContents 23

SEARSWEEDWACKER ®REPAIR PARTS LIST -- Model 358.798141.28.0cc:

eu ,E'rOR 3S 83

Figure 4r r

28 2B

J Gasket

KEY IPART QTY.

NO. lNO. REQ.

1 35017 I

2 35191 1

335164 1

435156 1

535178 t

635166 1

735133 1

8 35007 1

935138 1

1 35015 "1

11 35132 1

12 35023 I

13 35141 1

14 35106 1

15 35031 1

16 35031 1

* Contents of Gasket/Diaphragm Kit

+ Contents of Kwik Repair Kit "

DESCRIPTION

Screw-PumpCover

PumpCoverAss'y.(Inc!.#4)

* + Gasket-Pump

Screw.IdleAdjustment

+ Screen-lr_t

* + DiaphragrrvPump

Valve,Throttle

Clip-ThrottleShaft

Spring-ThrottleReturn

+ Screw-ThrottleValve

ShaftAssembly-Throttle

Spring-IdleNeedle

Needle-Idle

+ Spring-MeteringLever

+Valve-InletMetering

+ Lever-Metering

KEY

NO.

.17

PART

NO.

35O36

35142

35028

35016

35147

35042

35137

35151

35014

35153

35149

35185

35186

QTY.

REO.

DESCRIPTION

Spring-Hi Sp_ Needle

Needle-Hi Speed

,+Pin.Metering Lever

Screw-Metering Lever Pin

*+Gasket-Circuit Plate

Rate-Circuit

+Screw-O!rcuit Plate

* +Gasket-Metsring Diaphragm

* + Diaphragm Ass'y-Metering

Screw Assembly-Metering

Cover &Throttle Shaft Clip

Cover-Metering Diaphragm

I_t-Kwik Repair tot

(+Indicates Contents)

Kit-Gasket/Diaphragm

(*Indicates .Contents)

........ . . _ JLJ ............... I !L LIIJ IJ IIII II I II "1 IIIII I I I IIIII IIII II iiiiiii i I

iiiiiiiiiiiiiiiiiii iiiiiiiiilil,liilltJit] liji lii iitilliliiiiilli i al

¿¿¿¿¿¿¿¿¿HII I IIII . Ill I I JlII L [JlILLLJ2111iL_L _[LIWI]HII I II IIII millHim I I

The following accessories are available through Sears Retail Stores, Catalog, Outlets or Service Centers.

ITEM STOCK NO.

Safety Face Shield ..................................................................... 9-18613

Safety Goggles .......................................................................... 9.1859

2-Cycle Engine Oil 71-36555

Spark Plug ....... 71-79992

Replacement Trimmer Head ............................................................ 71-85764

Replacement Nylon Trimmer Line ...................................................... 71-85778

Replacement Spool with Line .................. ; ........................................ 71-85789

Flex Shaft Lube .......................................................................... 30102

Shoulder Strap ............................. . ........................................... 71-85783

ATTACHMENTS

I II I I III IIIII III IIIIIIIIIIIIIII IIII I ill

I I I II

POWER BLOWER

Model No. 358.795360

Whisks away dust, dirt, leaves, grass,

and light snow from walks, driveways

and patios. Fast_s wet, outdoor

areas such as ratios.

EDGER

Model No. 358.795350

Precisely edges walks, driveways, and

curbs. An adjustable depth guide con-

trols depth of cut. Blade is made from

high quaUty steel for strenglh andwear-

ing ability.

MINI-CULTIVATOR

Model No. 358.795480

Ideal for cultivating gardens, weeding

around shrubs, preparing flower beds,

and mixing additives into soil. Reaches

tight spots where larger tillers can't go.

Trees are heat treated for durability.

NcrrFs

II IIII IIIIIIII I IIIII III /11 IIIII I IIIIIII III III IIII

QUICK REFERENCE PAGE

Read and Follow All Warnit_, Safety Instructions and Operating Instructions.

Failure to do so can result in serious injury.

PREPARATION . • • ........ ................................. 3 & 5

I. Know all warnings andsafety instructions in this manual.

2. Wear safety face shield or goggles for eye protection.

3. Dresssafely -boots or safety shoes and heavy, long pants.

4. Check tool for worn, loose, missing or damaged parts; repair or replace as necessary before using the tool.

5. Inspect and ensure the area to be cut is safe.

6. Keep childreni bystanders, and animals 30 feet away.

FUELING. • . ...... ,, . ... ................. ................ . . . 9

I. Eliminate all sources of sparks or flame where fuel is mixed, poured or stored.

2. Use fuel not over 2 months old.

3. Mix andstore fuel in an approved, marked container.

4. Mix and pour fuel in an outdoor area.

5. Use 16partsregular unleaded gasoline to 1part air-cooled, 2-eycleengine oil.

6. Move a minimum of 10feet away from the fuel and fueling sitebefore startingengine

STARTING THEENGINE ........ ............ ............. . . . . . . 10

I. Extend line at least 4 inches fromthe head.

2. Rest the shield on the ground supportingthe trimmer head up offthe ground awayfrom objects and

on-lookers. •

3. Keep throttletrigger squeezed fully untilengine runs.

4. Pull the starterropesharplyand quickly.

OPERATING THE TOOL. 11

• ii •• • •• • oi_ • •• • • • I e •ii o ip o w • $ $ •• •••• •• ••••

1. Operate the tool from your right side only.

2. Do not operatethe tool at ahigher speed than necessary.

3. Release the throttle trigger and allow the engine to idle when not cutting.

4. Stop the engine by pushingthe"off"button. Hold the button down until engine stops.

MAINTENANCE...... .............. .............. ............ 14

t. Drain fuel from the unit before storing for 30 ormore days.

2. Disconnect spark plug before performing maintenance except for carburetoradjustments.

3. Clean air filter frequently but always after 5 tanks of fuel.

4. Store in adry place out of the reach of children.

IIII Illlllllllllllllllll IIII

operator's

manual

MODEL NO.

358.798141-28.0ec

How to Order

Repair parts

SEARS SERVICE

IS AT YOUR SERVICE

The ModelNumber will be foundunder the handle with the Serial Number. Always

mentionthe Model Number when requesting service or repair parts foryour unit.

AIIpartslisted hereinmay be orderedfrom any SearsService Centerand most Sears

Stores.

WHEN ORDERING REPAIR PARTS GIVE THE FOLLOWING INFORMA-

TION:AS,SHOWN!INTHIS_EIST ""

I. The PART NUMBER 3. The PAt_ DESCRIPTION

2. The MODEL NUMBER

35&798141 4. The NAME OF ITEM --

28,0cc Gas We*dtwad_er_

If the parts you need are not stocked locally, your order will be electronically transmit-

ted to a Sears Repair Parts Distribution Center for handling.

When you buy merchandise from

Sears you get.an extra something that

nobody else can offer, Sears Service.

Across town or across the country,

Sears Service follows you, providing

trustworthy, competent service techni-

cians using only Sears specified factory

parts.

• Yours Sears Merchandise takes on added value when you discover that Sears has Ser-

vice Units throughout the country. Each is staffed by Sears-Trained, professional

technicians using Sears approved methods.

66909-2-16987-1-17887 _

Sears, Roebuck and Co., Chicago, Ill. 60684 U.S.A.

.,, .,,, :

PRINTED IN U.S.A.

Craftsman 358798141 User Manual SEARS WEEDWACKER Manuals And Guides L0809175

CRAFTSMAN Line Trimmers/Weedwackers, Gas Manual L0809175 CRAFTSMAN Line Trimmers/Weedwackers, Gas Owner's Manual, CRAFTSMAN Line Trimmers/Weedwackers, Gas installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation