Craftsman 358798212 User Manual POULAN/WEED EATER Manuals And Guides L0808254
CRAFTSMAN Line Trimmers/Weedwackers, Gas Manual L0808254 CRAFTSMAN Line Trimmers/Weedwackers, Gas Owner's Manual, CRAFTSMAN Line Trimmers/Weedwackers, Gas installation guides
User Manual: Craftsman 358798212 358798212 CRAFTSMAN POULAN/WEED EATER - Manuals and Guides View the owners manual for your CRAFTSMAN POULAN/WEED EATER #358798212. Home:Lawn & Garden Parts:Craftsman Parts:358798212 Craftsman Grass trimmer (weed wacker) Manual
Open the PDF directly: View PDF .
Page Count: 13
Download | ![]() |
Open PDF In Browser | View PDF |
Operator's Manual CRFIFTSMFIN 24cc/1.3 cu.in. 2-Cycle 17 Inch Cutting Path / .080 In. Line GASOLINE WEEDWAOKER ® Model No. 358.798212 WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers Call 7 am-7 to your questions about this product: pm, Mon.-Sat., or 10 am-7 pm, Sun. 1-800-235-5878 Sears, 530087720 Roebuck 2/25/00 and Co., Hoffman _Hoors listed are Central Time) Estates, IL 60179 USA Warranty Statement Safety Rules Assembly Operation Maintenance Service & Adjustments 2 2 4 5 8 9 Storage Troubleshooting Chart Emissions Statement Parts List Spanish Parts and Ordering FULL ONE YEAR WARRANTY ON CRAFTSMAN WEEDWACKER _ LINE TRIMMER. For one year Weedwacker the operating repair, free of 11 12 12 14 17 Back "_GAS POWERED from the date of purchase, when this Craftsman Gas Powered Line Trimmer is maintained, lubricated, and tuned up according to and maintenance instructions in the Operator's Manual, Sears will charge, any defect in materials or workmanship. This warranty excludes nylon line, spark plug, and air filter, which are expendable parts and become worn during normal use. If this Weedwacker line trimmer is used for commercial purposes, this warranty applies for only 90 days from the date of purchase. If this Weedwacker line trimmer is used for rental purposes, this warranty applies for only 30 days from the date of purchase. This warranty applies only while this product is in use in the United States. WARRANTY SERVICE IS AVAILABLE BY RETURNING THE WEEDWACKER LINE TRIMMER TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D/817 WA Hoffman Estates, IL 60179 ,_ WARNING: When using gar- dening appliances, basic safety precautions must always be followed to reduce the risk of fire and serious injury. Read and follow all instructions. This power unit can be dangerous! Operator is responsible for following instructions and warnings on unit and in manual. Read entire Operator's Manual before using unit! Be thoroughly familiar with the controls and the proper use of the unit. Restrict the use of this unit to persons who have read, understand, and will follow the instructions and warnings on the unit and in the manual. Never allow children to operate this unit. SAFETY INFORMATION ON THE UNIT _, DANGER: flailing devices. for line trimmer use only. Use of any other accessories or attachments will increase the risk of injury. QOO _i WARNING: Eye Protection / -.tz_-_-__\--_" Never use blades or This unit is designed Trimmer line throws objects violently. You and others can be blinded/injured. Wear eye and leg protection. Keep body parts clear of rotating line. Keep children, bystanders, and animals 50 feet (15 meters) away. If approached stop unit immediately. E oots HazardZone If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, contact your Sears Service Center or call 1-800-235-5878. OPERATOR SAFETY • Always wear safety eye protection. • Always wear long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended. Do not go barefoot or wear sandals. Stay clear of spinning line. • Secure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line. • Do not operate when you are tired, ill, upset, or under the influence of alcohol, drugs, or medication. • Wear hearing protection. • Never start or run inside a closed room or building. Breathing exhaust fumes can kill. • Keep handles free from oil and fuel. UNIT / MAINTENANCE SAFETY • Disconnect the spark plug before performing maintenance except carburetor adjustments. • Look for and replace damaged or loose parts before each use. Look for and repair fuel leaks before use. Keep in good working condition. • Replace trimmer head parts that are chipped, cracked, broken, or damaged in any other way before using the unit. • Make sure unit is assembled correctly as shown in this manual. • Make carburetor adjustments with lower end supported to prevent line from contacting any object. • Keep others away when making carburetor adjustments. • Use only recommended Craftsman accessories and replacement parts. FUEL SAFETY • Mix and pour fuel outdoors. • Keep away from sparks or flames. • Use a container approved for fuel. • Do not smoke or allow smoking near fuel or the unit. • Wipe up all fuel spills. • Move at least 10 feet (3 meters) away from fueling site before starting engine. • Stop engine and allow to cool before removing fuel cap. CUTTING SAFETY • Use only for trimming, scalping, mowing, edging, and sweeping. Do not use for pruning or hedge trimming. • Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury. • Keep firm footing and balance. Do not overreach. • Keep all parts of your body away from muffler and spinning line. Keep engine below waist level. A hot muffler can cause serious burns. • Cutting on left side of the shield will throw debris away from the operator. TRANSPORTING AND STORAGE • Allow engine to cool; secure unit before storing or transporting in vehicle. • Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the engine and letting it run until it stops. • Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store unit so line limiter cannot accidentally cause injury. The unit can be hung by the tube. • Store unit out of reach of children. If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, call 1-800-235-5878. SPECIAL NOTICE: This unit is not equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arrestor screen. If you operate in a locale weather hasbeen linked toblood vesseldamage inotherwise healthy people. Ifsymptoms occur suchas numbness, pain, lossofstrength, change inskincolorortexture, orloss offeeling inthefingers, hands, or joints, discontinue theuseofthistool attention. AnantiSPECIAL NOTICE: Exposure tovibra- andseekmedical tionsthrough prolonged useofgaso- vibration system doesnotguarantee linepowered hand toolscould cause theavoidance ofthese problems. Usblood vessel ornerve damage inthe erswhooperate power toolsonaconfingers, hands, andjoints ofpeople tinualandregular basis mustmonitor prone tocirculation disorders orabnor- closely theirphysical condition andthe ofthistool. malswellings. Prolonged useincold condition where suchregulations exist, youare legally responsible forinstalling and maintaining theoperating condition of these parts. Failure todosoisaviolationoflaw.Contact aSears Service Center forthecorrect parts. CARTON CONTENTS • Loosen wing nut or knob on handle. Check carton contents against thefol- • Rotate the handle on the tube to an upright position; retighten wing nut. lowing list. Model 358.798212 ATTACHING SHIELD • Trimmer _/L WARNING: The shield must be • Shield properly installed. The shield provides • WingNut(screwed ontoshield) partial protection from the risk of thrown • Container ofOil to the operator and others and is Examine partsfordamage. Donotuse objects equipped with a line limiter which cuts damaged parts. line to the proper length. The line NOTE: Ifyouneedassistance orfind excess limiter (on underside of shield) is sharp parts missing ordamaged, call and can cut you. For proper orientation, 1-800-235-5878. illustration in OPERATION section. Itisnormal forthefuelfiltertorattlein see • Remove wing nut from shield. theempty fueltank. • Insert bracket into slot as shown. Finding fueloroilresidue onmuffler is • Pivot shield until bolt passes through normal duetocarburetor adjustments hole in bracket. andtesting donebythemanufacturer.• Securely tighten wing nut onto bolt. ASSEMBLY Slot WARNING: Ifreceived asShield sembled, repeat allsteps toensure Bracket yourunitisproperly assembled andall fasteners aresecure. ADJUSTING THE HANDLE WARNING: When adjusting the handle, be sure it remains between the trigger and the safety label. Wing Nut KNOW YOUR TRIMMER READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare theillustrations withyourunittofamiliarize yourself withthelocation of the various controls and adjustments. ence. Save this manual for future refer- Assist Handle Tube Trimmer Head \\ Throttle Muffler ON/STOP Trigger ........... Switch \ Spark Plug Starter ...... Shield Choke Lever \ Primer Bulb Fuel Mix Fill Cap CHOKE ON/STOP SWITCH The STOP switch is used to stop engine. Press and hold switch to stop engine. PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form. BEFORE _i, STARTING WARNING: The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After the engine attempts to start, move the choke lever to the HALF CHOKE position. Once engine has started, move the choke lever to the OFF CHOKE position. ENGINE Be sureto engine damage. When mixing fuel, follow instructions printed on container. read Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit. the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-235-5878. FUELING Line Limiter Blade IMPORTANT ENGINE Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil. We recommend Craftsman brand oil. Mix gasoline and oil at a ratio of 40:1 (A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). DO NOT USE automotive oil or boat oil. These oils will cause To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the 5 engine andletitrununtilthefuellines • Move choke lever to HALF CHOKE andcarburetor areempty. Usefresh position. fuelnextseason. • Pull starter rope handle no more than Never useengine orcarburetor clean- 6 pulls, until engine runs. erproducts inthefueltankorperma- NOTE: If the engine has not started nentdamage mayoccur. after 6 pulls (at HALF CHOKE), check to SeetheSTORAGE section foraddition- make sure the choke lever is in the alinformation. proper position. Then, move the choke STOPPING YOUR ENGINE lever to the FULL CHOKE position and • Press andholdtheON/STOP switch press the primer bulb 6 times; squeeze and hold the throttle trigger and pull intheSTOP position. starter rope 2 more times. Move • Ifengine doesnotstop,move choke the the choke lever to HALF CHOKE and lever toFULL CHOKE position. Choke Lever pull the starter rope until the engine Engine runs, but no more than 6 more pulls. If Stop the engine still has not started, it is Switch ", STARTING YOUR ENGINE COLD ENGINE OR WARM ENGINE AFTER RUNNING OUT OF FUEL WARNING: The trimmer head will turn while starting the engine. Avoid any contact with the muffler. A hot muffler can cause serious burns. • Set unit on a flat surface. • Slowly press the primer bulb 6 times. • Move choke lever to FULL CHOKE position. • Squeeze the throttle trigger fully and hold through all remaining steps. __B Ch°ke Lever I rimer ulb • Pull starter rope handle sharply 6 times. NOTE: If the engine sounds as if it is trying to start before the 6th pull, go to the next step. probably flooded. Proceed to STARTING A FLOODED ENGINE. • Allow the engine to run 10 seconds, then move the choke lever to OFF CHOKE. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trigger. NOTE: If engine dies with the choke lever at the OFF CHOKE position, move the choke lever to HALF CHOKE and pull the rope until engine runs. STARTING A WARM ENGINE • Move choke lever to HALF CHOKE position. • Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly. • Pull starter rope sharply until engine runs, but no more than 5 pulls. • Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE. NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded. DIFFICULT STARTING OR STARTING A FLOODED ENGINE Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn't start, refer to TROUBLESHOOTING CHART or call 1-800-235-5878. To advance line, tap bottom of trimmer head on ground one time. OPERATING INSTRUCTIONS OPERATING POSITION ALWAYS WEAR: _ ,,_'_'_ H_°;gy _t_s Cut from Llrnplei_e rg_hU.t s line t° "_ _-.. Eye Protection ___ your right to your left. Bring the engine to cutting speed before entering the material to be cut. Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to "weld" onto the spool. If the trimmer head does not turn when the engine is in operation, make sure the drive shaft housing is properly seated in engine shroud. Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine: • Release the throttle trigger. • Push and hold down the on/stop switch until the engine has stopped completely. TRIMMER LINE ADVANCE The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle. Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head. Ifthe line is worn down to 2 in. (5 cm) or less, more than one tap will be required to obtain the most efficient line length. ,_ WARNING: Use only .080" (2 mm) diameter line. Other sizes of line will not advance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury. CUTTING METHODS ,_ WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard. • The tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below. Tip of the Line Line Crowded Into Does The Cutting Work Area The most efficient line length is the maximum length allowed by the line limiter. Always keep the shield in place when the tool is being operated. To Advance Line: • Operate the engine at full throttle. • Hold the trimmer head parallel to and above the grassy area. • Tap the bottom of the trimmer head lightly on the ground one time. Approximately 2 in. (5 cm) of line will be advanced with each tap. • The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. To help avoid damage especially to delicate vegetation or trees with tender bark, shorten line to 4-5 in. (10-13 cm) and use at less than full throttle. • For trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially: • During light duty cutting. • Near objects around which the line can wrap such as small posts, trees or fence wire. • For mowing or sweeping, use full throttle for a good clean job. MOWING - Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool. Mowing I] ,_ WARNING: Always wear eye protection. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. TRIMMING - Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area. Trimming .___. -- ;_ SWEEPING - The fanning action of the rotating line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side. - ".L" Sweeping 3in. (8 cm) Above Ground ," _-,,_\ _ - _"_1_, SCALPING - The scalping technique removes unwanted vegetation. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. Scalping ........... MAINTENANCE EDGING - Your unit can be used for edging sidewalks, patios, driveways, etc. While edging, allow the tip of the line to make contact. Do not force line. Take extra caution while edging as objects can be thrown by trimmer line. Edging _/ SCHEDULE CARE & MAINTENANCE Check for Loose fasteners Check for damaged TASK and parts or worn parts WHEN TO PERFORM Before each use Before each use Clean unit and labels After each use Clean air filter Every 5 hours of operation Replace Yearly spark plug GENERAL RECOMMENDATIONS formance andincreases fuelconsumpemissions. Always Thewarranty onthisunitdoesnotcov- tionandharmful clean afterevery 5 hours ofoperation. eritems thathavebeen subjected to • Clean thecover andtheareaaround operator abuse ornegligence. Toreittokeep dirtfromfalling intothe ceive fullvalue fromthewarranty, the chamber when thecover operator must maintain unitasinstruct- carburetor edinthismanual. Various adjustments isremoved. • Remove partsasillustrated. willneedtobemade periodically to NOTE:Donotclean filteringasoline properly maintain yourunit. orother flammable solvent toavoid CHECK FOR LOOSE creating afirehazard orproducing FASTENERS ANDPARTS harmful evaporative emissions. • Spark PlugBoot • Wash thefilterinsoapandwater. • AirFilter • Allow filtertodry. • Housing Screws • Addafewdrops ofoiltothefilter; • Assist Handle Screws squeeze thefiltertodistribute oil. • Debris Shield • Replace parts. CHECK FOR DAMAGED OR WORN PARTS __O.___ FiIter Refer replacement ofdamaged/worn parts toyourSears Service Center. Screws • ON/STOP Switch - Ensure ON/STOP switch functions properly bypressing andholding theswitch intheSTOP Cover position. Make sureengine stops; thenrestart engine andcontinue. REPLACE SPARK PLUG • Fuel Tank- Discontinue useofunitif Replace thespark plugeach yearto fueltankshows signs ofdamage or ensure theengine starts easier and leaks. runs b etter. Set s park p lug gap at • Debris Shield - Discontinue useof .025in.Ignition timing isfixedand unitifdebris shield isdamaged. nonadjustable. • Twist, thenpulloffspark plugboot. CLEAN UNIT & LABELS • Remove spark plugfromcylinder • Clean theunitusing adamp cloth anddiscard. withamilddetergent. withChampion CJ-8Y spark • Wipe offunitwithaclean drycloth. • Replace plugandtighten witha3/4in.socket CLEAN AIRFILTER wrench (10-12 ft.-Ibs). Adirtyairfilterdecreases engine per- • Reinstall thespark plugboot. REPLACING THELINE • Push andholdtheengine STOP switch • • • • • Insert ends of line about 1/2 inch (1 cm) into the small holes inside spool. in the STOP/OFF position until the unit has fully stopped. Disconnect the spark plug lead wire. Remove the spool by firmly pulling on the tap button. Clean entire surface of hub and spool. Replace with a pre-wound spool, or cut two 12.5 foot (3.8 m) lengths of .080" (2 mm) diameter Craftsman brand line. Never use wire, rope, string, etc., which can break off and become a dangerous missile. Spool /_ .............. _'-// Small Holes • Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool. • Push the line into the notches, leaving 3 to 5 inches (7 - 12 cm) unwound. 9 • Insert thelineintothetheexitholes in thehubasshown intheillustration. Lineexitholes Line in Notch \ Screw (with Limiter Cap) Hub f Line in Notch • Align notches with the line exit hole. • Push the spool into the hub until it snaps into place. • Pull the line extending outside of the hub to release it from the notch. CARBURETOR Z_ _, WARNING: ADJUSTMENT The trimmer head will be spinning during most of this procedure. Wear your protective equipment and observe all safety precautions. After making mixture adjustments, recheck idle speed. Carburetor adjustment is critical and if done improperly can permanently damage the engine as well as the carburetor. If you require further assistance or are unsure about performing this procedure, call our customer assistance help line at 1-800-235-5878. Old fuel, a dirty air filter, a dirty fuel filter, or flooding may give the impression of an improperly adjusted carburetor. Check these conditions before adjusting the carburetor. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: • Engine will not idle. See IDLE SPEED under adjusting procedure. • Engine dies or hesitates instead of accelerating. See ACCELERATION CHECK under adjusting procedure. • Loss of cutting power. See MIXTURE ADJUSTMENT under adjusting procedure. There are two adjustment the carburetor. screws on Air Filter "_ Cover CARBURETOR PRESETS When making carburetor preset adjustments, do not force plastic limiter caps beyond stops or damage will occur. If carburetor presets are not needed, proceed to ADJUSTING PROCEDURE, IDLE SPEED. To adjust presets: • Turn mixture screw counterclockwise until it stops. • Turn the idle speed screw clockwise until it stops. Now turn counterclockwise 4-1/2 turns. • Start motor, cut grass for 3 minutes, and proceed to the adjustment section. If engine does not start, refer to TROUBLESHOOTING CHART or call 1-800-235-5878. • If engine performance is acceptable at the preset positions, no further adjustment is necessary. ADJUSTING PROCEDURE Idle Speed Allow engine to idle. Adjust speed until engine runs without stalling. • Turn clockwise to increase engine speed if engine stalls or dies. • Turn counterclockwise to decrease speed. No further adjustments are necessary if performance is satisfactory. Mixture Adjustment "H" DO NOT operate engine at full throttle for prolonged periods while making adjustments. Damage to the engine can occur. Extend line to the length allow by the line limiter and cut some grass. Based on performance while cutting, turn the mixture adjustment in 1/16-turn increments as follows: • Clockwise until the engine has good power while cutting with no hesitation. Do not adjust by sound or speed, but 10 judge by how well the engine performs while cutting. • Counterclockwise if the engine has speed but dies or lacks power while cutting. After completing adjustments, check for acceleration. Reset if necessary. Acceleration Prepare unit for storage at end of season or if it will not be used for 30 days or more. stabilizer to the gasoline in the fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer. Craftsman 40:1,2-cycle engine oil (air cooled) is already blended with fuel stabilizer. If you do not use this Sears oil, you can add a fuel stabilizer to your fuel tank. ,_ WARNING: • Allow engine to cool, and secure the unit before storing or transporting. • Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store unit with all guards in place. Position unit so that any sharp object cannot accidentally cause injury. • Store unit and fuel well out of the reach of children. EXTERNAL SURFACES If your unit is to be stored for a period of time, clean it thoroughly before storage. Store in a clean dry area. • Lightly oil external metal surfaces. FUEL SYSTEM Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine. Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add Check If engine dies or hesitates instead of accelerating, turn mixture adjustment counterclockwise until you have smooth acceleration. Recheck and adjust as necessary formance. for acceptable per- INTERNAL ENGINE • Remove spark plug and pour 1 teaspoon of 40:1,2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. • Replace spark plug with new one of recommended type and heat range. • Clean air filter. • Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts. • At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. OTHER • Do not store gasoline from one season to another. • Replace your gasoline can if it starts to rust. 11 TROUBLESHOOTING CHART TROUBLE CAUSE REMEDY Engine will not start. • • • • • • • • Engine flooded. Fuel tank empty. Spark plug not firing. Fuel not reaching carburetor. • Compression Engine will not idle properly. See "Starting Instructions." Fill tank with correct fuel mixture. Install new spark plug. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. • Contact a Sears Service Center. low. • Idle speed set too low. • Idle speed set too high. • Carburetor requires adjustment. • Crankshaft seals worn. • Compression low. Engine will not accelerate, lacks power, or dies under a load. Engine smokes excessively. • Air filter dirty. • Spark plug fouled. • Carburetor requires adjustment. • Carbon build up. • Compression low. • Choke partially on. • Fuel mixture incorrect. • Air filter dirty. • Carburetor requires adjustment. Engine runs hot. • Fuel mixture incorrect. • Spark plug incorrect. • Carburetor requires adjustment • Carbon build up. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U. S. Environmental Protection Agency and SEARS, ROEBUCK AND CO., USA are pleased to explain the emissions control system warranty on your lawn and garden equipment engine. All new utility and lawn and garden equipment engines must be designed, built, and equipped to meet the stringent antismog standards. SEARS must warrant the emission control system on your lawn and garden equipment engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your • Adjust idle speed screw clockwise to increase speed. • Adjust idle speed screw counterclockwise to reduce speed. • See "Carburetor Adjustments." • Contact a Sears Service • Contact a Sears Service Center. Center. • Clean or replace air filter. • Clean or replace spark plug and re-gap. • See "Carburetor Adjustments." • Contact a Sears Service • Contact a Sears Service Center. Center. • Move choke to off position. • Empty fuel tank and refill with correct fuel mixture. • Clean or replace air filter. • See "Carburetor Adjustments." • See "Fueling Your Unit." • Replace with correct spark plug. • See "Carburetor Adjustments." • Contact a Sears Service Center. lawn and garden equipment engine. Your emission control system includes parts such as the carburetor and the ignition system. Where a warrantable condition exits, SEARS will repair your lawn and garden equipment engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor. MANUFACTURER'S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be 12 repaired orreplaced bySEARS. maintenance, or which is scheduled OWNER'S WARRANTY RESPONSI-only for regular inspection to the effect BILITIES: Asthelawnandgarden of "repair or replace as necessary" equipment engine owner, youarere- shall be warranted for 2 years. Any sponsible fortheperformance ofthe warranted part which is scheduled for required maintenance listed inyour replacement as required maintenance Owner's Manual. SEARS recommends shall be warranted for the period of thatyouretain allreceipts covering time up to the first scheduled replacemaintenance onyourlawnandgarden ment point for that part. DIAGNOSIS: equipment engine, butSEARS cannot The owner shall not be charged for denywarranty solely forthelackofre- diagnostic labor which leads to the deceipts orforyourfailure toensure the termination that a warranted part is deperformance ofallscheduled mainte- fective if the diagnostic work is pernance.Asthelawnandgarden formed at an approved SEARS equipment engine owner, youshould servicing center. CONSEQUENTIAL beaware thatSEARS maydeny you DAMAGES: SEARS may be liable for warranty coverage ifyourlawnand damages to other engine components garden equipment engine orapartofit caused by the failure of a warranted hasfailed duetoabuse, neglect, impart still under warranty. WHAT IS proper maintenance, unapproved NOT COVERED: All failures caused modifications, ortheuseofpartsnot by abuse, neglect, or improper maintenance are not covered. ADD-ON OR made orapproved bytheoriginal equipment manufacturer. Youarere- MODIFIED PARTS: The use of add-on sponsible forpresenting yourlawnand or modified parts can be grounds for disgarden equipment engine toa SEARS allowing a warranty claim. SEARS is not liable to cover failures of warranted authorized repair center assoon asa problem exists. Warranty repairs parts caused by the use of add-on or should becompleted ina reasonable modified parts. HOW TO FILE A amount oftime,nottoexceed 30 days. CLAIM: If you have any questions reIf you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call SEARS at 1-800-473-7247 WARRANTY COMMENCEMENT DATE: The warranty period begins on the date the lawn and garden equipment engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of purchase. WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of any warranted part will be performed at no charge to the owner at an approved SEARS servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call SEARS at 1-800-473-7247. WARRANTY PERIOD: Any warranted part which is not scheduled for replacement as required garding your warranty rights and responsibilities, you should contact your nearest authorized service center or call SEARS at 1-800-473-7247. WHERE TO GET WARRANTY SERVICE: Warranty services or repairs shall be provided at all SEARS service centers. call: 1-800-473-7247. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS: Any SEARS approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up to maintenance schedule), Ignition Module. MAINTENANCE STATEMENT: The owner is responsible for the performance of all required maintenance as defined in the owner's manual. 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 13 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Mon Aug 25 04:13:22 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools