Craftsman 358799461 User Manual ELECTRIC TRIMMER Manuals And Guides L0905105

CRAFTSMAN Line Trimmers/Weedwackers, Electric Manual L0905105 CRAFTSMAN Line Trimmers/Weedwackers, Electric Owner's Manual, CRAFTSMAN Line Trimmers/Weedwackers, Electric installation guides

User Manual: Craftsman 358799461 358799461 CRAFTSMAN ELECTRIC TRIMMER - Manuals and Guides View the owners manual for your CRAFTSMAN ELECTRIC TRIMMER #358799461. Home:Lawn & Garden Parts:Craftsman Parts:358799461 Craftsman Grass trimmer (weed wacker) Manual

Open the PDF directly: View PDF PDF.
Page Count: 10

Operator's Manual
ICRRFTSMRN°I
4.0 Amp Motor
13 Inch Cutting Path/.065 In. Line
ELECTRIC WEEDWACKER ®
Model No.
358.799461
@
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon-Sat; 10 am-7 pm, Sun
1-800-235-5878 (HourslistedareCentralTime)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
530088611 10/9/00
Warranty Statement 2 Parts Available 9
Safety Rules 2 Storage 9
Assembly 5 Troubleshooting Table 10
Operation 6
Maintenance 8 Spanish 11
Service & Adjustments 9 Parts Ordering Back Cover
FULL ONE YEAR WARRANTY ON CRAFTSMAN ELECTRIC WEEDWACKER ®
LINE TRIMMER
If this Craftsman Electric Weedwacker <_ Line Trimmer fails to perform properly
due to a defect in material or workmanship within (1) one year from the date of
purchase, Sears will repair or replace it, free of charge.
This warranty does not cover the nylon line.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN ELECTRIC
WEEDWACKER :R LINE TRIMMER TO THE NEAREST SEARS STORE OR SERVICE CEN-
TER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179
.'%_
m_WARNIN_I: When using electric
gardening appliances, basic safety
precautions must always be followed
to reduce the risk of fire, electric
shock, and serious injury. Read and
follow all instructions.
_ AFETY INFORMATIONON THE UNIT
This power unit can be dangerous!
Operator is responsible for following
the warnings and instructions in this
manual and on the unit. Read entire
Operator's Manual before using unit!
Be thoroughly familiar with the con-
trols and the proper use of the unit.
Restrict the use of this unit to persons
who read, understand, and follow unit
and manual warnings and instruc-
tions. Never allow children to operate
this unit. Close attention is necesary
when used near children.
dI_DAN_IER" Never use blades or
flailing devices. Unit is designed for line
trimmer use only. Use of any other ac-
cessories or attachments will increase
the risk of injury.
@
,_ WARNING: Trimmer line throws
objects violently. You and others can
be blinded/injured. Wear safety
glasses, boots, and leg protection.
Keep body parts clear of rotating line.
Safety Glasses or similar eye 3rotection
Boots
Keep children, bystanders, and ani-
mals 50 feet (15 meters) away. If ap-
proached stop unit immediately.
If situations occur which are not cov-
ered in this manual, use care and
good judgement. If you need assis-
tance, call 1-800-235-5878.
OPERATOR SAFETY
• Dress properly. Always wear safety
glasses or similar eye protection
when operating, or performing main-
tenance on your unit. (Safety
glasses are available.) Always wear
face or dust mask if operation is
dusty.Alwayswearheavy,long
pants,longsleeves,boots,and
gloves.Donotgobarefootorwear
sandals.
•Securehairaboveshoulderlength.
Secureorremovelooseclothing
andjewelryorclothingwithloosely
hangingties,straps,tassels,etc.
Theycanbecaughtinmovingparts.
• Beingfullycoveredalsohelpspro-
tectyoufromdebrisandpiecesof
toxicplantsthrownbyspinningline.
•StayAlert.Donotoperateunitwhen
youaretired,ill,orunderinfluence
ofalcohol,drugs,ormedication.
Watchwhatyouaredoing;usecom-
monsense.
• Avoidunintentionalstartingofthe
unit.Nevercarryunitwithyourfin-
gerontheswitch.Besurethe
switchisinOFFpositionwhencon-
nectingextensioncord.
ELECTRICALSAFETY
,_/kWARNING: Avoid a dangerous
environment. To reduce the risk of
electrical shock, do not use in rain, in
damp or wet locations, or around
swimming pools, hot tubs, etc. Do not
expose to snow, rain, or water to avoid
the possibility of electrical shock.
• Use a voltage supply as shown on
unit.
• Avoid dangerous situations. Do not
use in the presence of flammable
liquids or gases to avoid creating a
fire or explosion and/or causing
damage to unit.
• To reduce the risk of electrical
shock, this equipment has a polar-
ized plug (one blade is wider than
the other) and will require the use of
a polarized extension cord. The ap-
pliance plug will fit into a polarized
extension cord only one way. If the
plug does not fit fully into the exten-
sion cord, reverse the plug. If the
plug still does not fit, obtain a correct
polarized extension cord. A polar-
ized extension cord will require the
use of a polarized wall outlet. This
plug will fit into the polarized wall
outlet only one way. If plug does not
fit fully into the wall outlet, reverse
the plug. If the plug still does not fit,
contact a qualified electrician to
install the proper wall outlet. Do not
change the equipment plug, exten-
sion cord receptacle, or extension
cord plug in any way.
• To reduce risk of electrical shock,
use extension cords specifically
marked as suitable for outdoor ap-
pliances having electrical rating not
less than the rating of unit. Cord
must be marked with suffix "W-A" (in
Canada "W"). Make sure your exten-
sion cord is in good condition. In-
spect extension cord before use and
replace if damaged. Do not use a
damaged cord. Cord insulation
must be intact with no cracks or de-
terioration. Plug connectors must be
undamaged. An undersized exten-
sion cord will cause a drop in line
voltage resulting in loss of power
and overheating. If in doubt, use the
next heavier gauge. The lower the
gauge number, the heavier the cord
(see SELECT AN EXTENSION CORD).
Do not use multiple cords.
• Do not abuse cord. Never carry the
unit by the extension cord or yank
extension cord to disconnect unit.
• Use cord retainer to prevent discon-
nection of extension cord from unit.
See ATTACH THE ENTENSlON CORD
TO YOUR TRIMMER under the sec-
tion titled OPERATION.
• Do not use the unit if the switch
does not turn the unit on and off
properly. Repairs to the switch must
be made by your Sears Service
Center.
• Keep the extension cord clear of op-
erator and obstacles at all times. Do
not expose cords to heat, oil, water,
or sharp edges.
• To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
• Ground Fault Circuit Interrupter
(GFCI) protection should be pro-
vided on circuit or outlet to be used.
Receptacles are available having
built-in GFCl protection and may be
used for this measure of safety.
UNIT SAFETY
• Inspect unit before use. Replace
damaged parts. Make sure all han-
dles, guards, and fasteners are in
place and securely fastened. Parts
that are damaged must be repaired
or replaced by a Sears Service Cen-
ter. These include head parts that
are cracked, or chipped, guards,
and any other part that is damaged.
• Do not repair unit yourself.
• Use only .065" (1.65 mm) diameter
recommended trimmer line. (See
SERVICEANDADJUSTMENTS).Nev-
erusewire,rope,stringetc.
• Usespecifiedtrimmerspool.Make
surespoolisproperlyinstalledand
allpartsaresecurelyfastened.
• Useonlyrecommendedreplace-
mentpartsandaccessories.
CUTTINGSAFETY
• InspectareatobecutRemoveob
jects(rocksbrokenglassnails
wirestringetc.)whichcanbe
thrownorbecomeentangledincut-
tinghead.
• Donotoverreachorstandonunsta-
blesupport.Keepfirmfootingand
balance.
• Keepthecuttingheadbelowwaist
level.Donotraisehandlesabove
yourwaist.Cuttingheadcancome
dangerouslyclosetoyourbody.
• Keepawayfromspinningline.
• Useunitproperly.Useonlyfortrim-
ming,edging,scalping,andmow-
ing.Donotforceunit.Itwilldothe
jobbetterandwithlessriskofinjury
attherateforwhichitwasdesigned.
• Useonlyindaylightoringoodartifi-
ciallight.
MAINTENANCE SAFETY
,_WARNING: Disconnect unit
from the power supply before perform-
ing maintenance, or when changing
trimmer line.
• Maintain unit according to recom-
mended procedures. Keep cutting
line at proper length. Follow instruc-
tions for changing trimmer line.
• Have all service and maintenance
not explained in this manual per-
formed by a Sears Service Center to
avoid creating a hazard.
• Never douse or squirt the unit with
water or any other liquid. Clean unit
and labels with a damp sponge.
Keep handles dry, clean, and free
from oil and grease.
• Keep the air vents clean and free of
debris to avoid overheating the mo-
tor. Clean after each use.
TRANSPORTING AND STORAGE
• Stop the unit and disconnect the
power source when not in use.
• Carry the unit with motor stopped.
• Store the unit so the line limiter
blade (on underside of shield) can-
not cause injury.
• Store unit indoors in a high, dry
place out of the reach of children.
Store unit unplugged.
DOUBLE INSULATION CONSTRUC-
TION
This unit is double insulated to help
protect against electric shock. Double
insulation construction consists of two
separate "layers" of electrical insula-
tion instead of grounding.
Tools built with this insulation system
are not intended to be grounded. No
grounding means is provided on this
unit, nor should a means of grounding
be added to this unit. As a result, the
extension cord used with your unit can
be plugged into any polarized 120 volt
electrical outlet.
Safety precautions must be observed
when operating any electrical tool.
The double insulation system only
provides added protection against in-
jury resulting from an internal electrical
insulation failure.
_/L WARNING: All electrical repairs
to this unit, including housing, switch,
motor, etc., must be diagnosed and
repaired by qualified service person-
nel. Replacement parts for a double
insulated appliance must be recom-
mended by the manufacturer. A
double insulated appliance is marked
with the words "double insulation" or
"double insulated." The symbol
(square within a square) [] may also
be marked on the appliance. Failure
to have the unit repaired by qualified
service personnel can cause the
double insulation construction to be-
come ineffective and result in serious
injury.
SAVE THESE INSTRUCTIONS
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 358.799461
• Trimmer
• Shield
• Cutting line dispenser with extra line
Examine parts for damage. Do not
use damaged parts.
NOTE: If you need assistance or find
parts missing or damaged, call
1-800-235-5878.
ASSEMBLY
'_WARNING: If received as-
sembled, review all assembly steps to
ensure your unit is properly as-
sembled and all fasteners are secure.
• Extend the tube until it snaps into
place.
ADJUSTING UPPER HANDLE
• Press button located on the under-
side of the upper handle and extend
handle to a comfortable position.
Button _
ADJUSTING ASSIST HANDLE
1. Loosen wing nut or knob on han-
dle.
2. Rotate the handle on the tube to
an upright position; place in a
comfortable position and retighten
wing nut or knob.
ATTACHING THE SHIELD
dBbWARNING: The shield must be
properly installed. The shield provides
partial protection from the risk of
thrown objects to the operator and
others. Your unit is equipped with a
line limiter blade, which cuts excess
line to the proper length while running.
The line limiter blade (on underside of
shield) is sharp and can cut you.
NOTE: If shield is not properly
installed, damage to unit (including
motor failure) will result.
1. Align the installation arrow on the
shield with the installation arrow on
the motor housing (see illustration
below).
2. Insert the shield onto the motor
housing. Ensure cutting line re-
mains free to rotate and is not
caught between the shield and the
motor housing.
3. Twist the shield as illustrated until
it snaps securely into place. Make
sure the shield is facing the back
of the unit as shown on the front
cover of this manual.
ALIGN INSTALLATION ARROWS
CAUTION: Sharp line limiter blade
KNOWYOURTRIMMER
READTHISOPERATOR'SMANUALANDSAFETYRULESBEFOREOPERATINGYOUR
UNIT.Comparetheillustrationswithyourunittofamiliarizeyourselfwiththeloca-
tion of the various controls and adjustments. Save this manual for future refer-
ence.
Plug _ t'_ Assist Handle
Cord
Retainer
Trigger
Switch
Bu_on Motor Housing
J
ge
Air Vents
Button Debris
Edge Guide
Semi-automatic
Head with
.065" line
lap Button
_ Line Limiter Blade
RECESSED PLUG
The RECESSED PLUG is where you at-
tach your extension cord to the unit.
TRIGGER SWITCH
The TRIGGER SWITCH is used to turn
on the unit. Squeeze the trigger switch
to operate the unit.
LINE LIMITER
The LINE LIMITER cuts the cutting line
to the proper cutting length.
ASSIST HANDLE
The ASSIST HANDLE is used to help
hold and guide the unit.
HANDLE BUTTON
The HANDLE BUTTON is used to adjust
the upper handle to a comfortable op-
erating position.
OPERATING INSTRUCTIONS
Use only a voltage supply as specified
on your unit.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord Gauge
25 Ft. (7.5 m) 18 Gauge
50 Ft. (15 m) 16 Gauge
100 Ft. (30 m) 16 Gauge
SEMI-AUTOMATIC HEAD
The SEMI-AUTOMATIC HEAD holds the
cutting line and rotates during opera-
tion.
TWIST AND EDGE BUTTON
The TWIST AND EDGE BUTTON is used
to twist the lower portion of the unit
into an edging position.
EDGE GUIDE
The EDGE GUIDE protects the unit
from contacting the ground during
edging.
TAP BUTTON
The TAP BUTTON is used to advance
the cutting line during operation and to
remove the spool during line replace-
ment.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the
handle and around the hook. Insure
the plug and cord are firmly and fully
engaged.
Extension cords are available for this
unit at Sears.
6
CORRECTOPERATINGPOSITION
Trimming Edging
_WARNING:Alwaysweareye
protection.Neverleanoverthetrim-
merhead.Rocksordebriscanrico-
chetorbethrownintoeyesandface
andcauseblindnessorotherserious
injury.
Whenoperatingunit,standasshown
andcheckforthefollowing:
•Weareyeprotectionandheavy
clothing.
• Holdtriggerhandlewithrighthand
andassisthandlewithlefthand.
• Keepunitbelowwaistlevel.
•Cutfromyourrighttoyourlefttoen-
sure debris is thrown away from you.
Without bending over, keep line near
and parallel to the ground (perpen-
dicular when edging) and not
crowded into material being cut.
ADVANCING THE CUTTING LINE
Advance line by tapping bottom of cut-
ting head lightly on the ground while
unit is running at full speed. A metal
blade attached to the shield will cut
the line to the proper length.
TRIMMING
Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground
and at an angle. Allow only the tip of
the line to make contact. Do not force
trimmer line into work area.
EDGING POSITION
You can press this button and twist
the lower portion 180 ° into an edging
position.
Button
EDGING
While edging allow the tip of the line to
make contact. Do not force the line.
The edge guard helps protect the unit
and keeps the unit from contacting the
ground. Take extra caution while edg-
ing as objects can be thrown from the
trimmer line.
Edging
SCALPING
The scalping technique removes un-
wanted vegetation. Hold the bottom of
the trimmer head about 3 in. (8 cm)
above the ground and at an angle. Al-
low the tip of the line to strike the
ground around trees, posts, monu-
ments, etc. This technique increases
line wear.
Scalping
MOWING
Your trimmer is ideal for mowing in
places conventional lawn mowers
cannot reach. In the mowing position,
keep the line parallel to the ground.
Avoid pressing the head into the
ground as this can scalp the ground
and damage the tool.
Mowing clean up. Keep the line parallel to and
above the surfaces being swept and
move the tool from side to side.
Sweeping
SWEEPING
The fanning action of the rotating line
can be used for a quick and easy
CUSTOMER RESPONSIBILITIES
_, WARNING: Disconnect power source before performing maintenance.
CARE & MAINTENANCE TASK WHEN TO PERFORM
Check for loose fasteners and parts Before each use
Check for damaged or worn parts Before each use
Inspect and clean unit and labels After each use
GENERAL RECOMMENDATIONS
The warranty on this unit does not
cover items that have been subjected
to operator abuse or negligence. To
receive full value from the warranty,
the operator must maintain unit as
instructed in this manual. Various ad-
justments will need to be made peri-
odically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE
FASTENERS AND PARTS
•Housing Screws
• Assist Handle Screws
• Debris Shield
• Edge Guide
CHECK FOR DAMAGED OR
WORN PARTS
Contact Sears Service Center for re-
placement of damaged or worn parts.
• Trigger Switch - Ensure switch func-
tions properly by pressing and re-
leasing the trigger switch. Make sure
motor stops.
• Debris Shield - Discontinue use of
unit if debris shield is damaged.
AFTER EACH USE
INSPECTAND CLEAN UNIT AND LA-
BELS
• After each use, inspect complete
unit for loose or damaged parts.
Clean the unit using a damp cloth
with a mild detergent.
• Wipe off unit with a clean dry cloth.
REPLACINGTHELINE
1. Removethespoolbyfirmlypulling
onthetapbutton.
2. Cleanentiresurfaceofhuband
spool.
3. Replacewithapre-woundspool
(#71-85837),orcutalengthof30
feetof.065"(1.6mm)diameter
Craftsman®ProTrimmerline.Use
ofheavierlinescouldoverloadthe
unitanddamageunit.Neveruse
wire,rope,string,etc.,whichcan
breakoffandbecomeadanger-
ousmissile.
4. Insertoneendofthelineabout1/2
inch(1cm)intothesmallholein-
sidethespool.
5. Windthelineevenlyandtightly
ontothespool.Windinthedirec-
tionofthearrowfoundonthe
spool.
6. Pushthelineintothenotch,leav-
ing3to5inches(7- 12cm)un-
wound.
7. Insertthelineintotheexit hole in
the hub as shown in the illustra-
USER REPLACEABLE SERVICE PARTS
tion.
8. Align the notch with the line exit
hole.
9. Push the spool into the hub until it
snaps into place.
10. Pull on the line extending outside
the hub to release it from the
notch; otherwise, the unit will not
function properly.
Small
Spool
Tap
Button
Line in Notch _
Hub Line exit hole
REPLACEMENT PART PART NUMBER
Spool with .065" Pro Trimmer Line 71-85837
Assist Handle 530401991
Bolt, Assist Handle, 1/4-20 530401989
Wing Nut, Assist Handle 530016118
Shield Assembly 530402672
Edge Guide 530402663
Screw, Edge Guide Retaining 530015815
Prepare unit for storage after each
use by performing the following steps:
_, WARNING:
• Stop the unit and disconnect the
power source when not in use.
• Carry the unit with motor stopped.
• Store the unit so the line limiter
blade cannot cause injury.
• Store unit and extension cord in-
doors in a high, dry place out of the
reach of children. Store unit un-
plugged.
• Store unit with all guards in place.
Position unit so that any sharp ob-
ject cannot accidentally cause injury.
TROUBLESHOOTINGTABLE
,_WARNING: Always stop unit and disconnect from the power source before
performing all of the recommended remedies below except remedies that re-
quire unit to be operating.
TROUBLE
Semi-automatic
head stops
under a load or
does not turn
when switch is
pressed.
Line does not
advance or
breaks while
cutting.
CAUSE REMEDY
1. Crowding trimmer line 1. Allow tip of line to do the cutting.
against material being
cut.
2. Electrical failure. 2. Contact your Sears Service Center.
3. Thrown circuit breaker. 3. Check Breaker Box.
4. Debris stopping head. 4. Remove debris.
1. Check line routing.
2. Rewind line tightly and evenly.
1. Line improperly routed
in head.
2. Line improperly
wound onto spool.
3. Incorrect line size
4. Not enough line
outside of head.
5. Dirt buildup on unit.
1. Line size is incorrect.
2. Incorrect spool.
3. Line is being crowded
against material being
cut.
1. Line improperly
routed in head.
2. Spool damaged.
1. Line improperly routed
in head.
2. Line size is incorrect.
3. Crowding line against
material being cut.
4. Spool worn or damaged.
Use only .065 in. (1.65mm) dia. line.
Remove cover and pull 4 in.
(10 cm) of line out of head.
Clean unit.
Use only .065 in. (1.65mm) dia. line.
Replace with correct spool.
Cut with tip of line fully extended.
5.
Line welds onto 1.
spool. 2.
3.
Line releases 1. Check line routing.
continuously.
2. Replace spool.
Line usage is 1. Check line routing.
excessive.
2. Replace spool.
3. Cut with tip of line fully extended.
4. Replace spool.
Line pulls back 1. Too little line outside 1. Remove cover and pull 4 in.
into head. of head. (10 cm) of line outside of head.
2. Line size incorrect. 2. Use only .065 in. (1.65 mm) dia. line.
10

Navigation menu