Craftsman 390269451 User Manual SUBMERSIBLE UTILITY PUMP Manuals And Guides L0406489
CRAFTSMAN Submersible Pumps Manual L0406489 CRAFTSMAN Submersible Pumps Owner's Manual, CRAFTSMAN Submersible Pumps installation guides
User Manual: Craftsman 390269451 390269451 CRAFTSMAN SUBMERSIBLE UTILITY PUMP - Manuals and Guides View the owners manual for your CRAFTSMAN SUBMERSIBLE UTILITY PUMP #390269451. Home:Plumbing Parts:Craftsman Parts:Craftsman SUBMERSIBLE UTILITY PUMP Manual
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
SEARS OWNER'S MANUAL MODEL NO. 390.269451 390.269551 CRAFTSMAN Model No. 390.269451 CRAFTSMAN PROFESSIONAL Model No. 390.269551 CAUTION: Read and Follow All Safety Rulesand Operating Instructions Before First Use of ThisProduct. Save ThisManual For Future Reference. I:RRFTSMRW SUBMERSIBLE UTILITY PUMP • Safety Instructions • Installation • Electrical • Repair Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 PRINTED IN U.SA U.S.A. Form No F642-9815 (Rev. 4/19/04) CONTENTS INTRODUCTION INTRODUCTION/WARRANTY 2 SAFETY 2 INSTALLATION .3 SER\qCE 4 PERFORMANCE .5 P.MITS 6 Please read our instructions before you Install and use )'our new pump, this will help )'ou obtain full value and good service from tt It will also help you avoid needless service costs that result from causes we cannot control and cannot cover in OLIF warranty LIMITED LIFETIME WARRANTY on CRAFTSMAN ° PROFESSIONAL I/4-HP SUBMERSIBLE PORTABLE UTILITY PUMP Prowded that tt is installed and operated[ acc_g to file Instructions in the owner's manual, ff this pump ever fails for the original purchaser due to a defect in materlal_ol_ workmazmhlp, i-cram it tO your rmarest Sears store, and Scars will replace it free of charge. You pay for labor ifyou choose to hav¢ _ install the replaccnmnt pump. FULL ONE YEAR WARRANTY For one year from the date of purchase, workmamhip. Warrant,i _.€€ Is avanab_ b,/eali_ ON CRAFTSMAhP SUBMERSIBLE PORTABLE UTILITY Sears will repair or replace this pump, free of chaege, ff defective PUMPS in material or Sears at 1-$O0-4-MY-HOME'. LI_ABILtTY ...... LIMITATION Seaea is not liable for loss or damage to property, nor for any incidental or consequential loss or expense from property damage, that results dtrectlg or mdirectly from the ttse of this product. Some states do not allow the exclusion or htmtatton of property, mcidemal or consequential damages, so the above limitation or exclusion may not apply to you This warranty applies only while this product is tl_ed m the United States. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state Sears, Roebuck and Co., Dept. 817WA, GENERAL SAFETY Hoffman Estates, IL 60179 INFORMATION NOTICE- This umt is not designed for apphcattons mvolvmg salt water or bnne' Use with salt water or brine will void b Keep work area clean, uncluttered and properly hghted - replace all unused tools and equipment vearrant_. c Keep visitors i _ Know the pump hazards apphcation, hmttations, and potential [AWARNING]Do not use in explosive atmospheres. Pump water only with this pump. Failure to follow this warning can result in personal injury and/or property damage. 2 Dtscommct 3 Release all presstire any component power before servicing 4 Dram water 5 Secure the discharge line before starting the pump An unsecured discharge line will wfup, possthly causing personal mlnry and/or property damage 6 Check hoses for weak or worn condition belbre maMng certain that all codnections are secure " Penodmally respect pump and system components form routine maintenance as required (See TENANCE, Page 4) 8 Proxide a means of pressure relief for pumps charge line can be shut-off or obstructed 9 Personal withm from the system the sTstem before servicmg se_Tzcmg each use, whose dis Safer',' a Wear safety glasses at all ttmes when working pumps PerblAIN- with from the work area d Make workshop child-proof - with padlocks, switches, and by removing starter ke)s master 10 When winng an elecmcally driven pump, follow electrical and safety codes, as w ell as the most recent National Electoral Code 1l This equipment is only for use on 115 volt (single phase) and is equipped with an approved 3-conductor cord and 3-prong, grounding-type plug. [AWARNING ]To before at a safe distance reduce the risk of electric shock, pull plug before servicing. This pump has not been investigated for use in swinlming pool areas. This pump is supplied with a grounding conductor and grounding-type attachment phtg. Be certain that it is connected only to a properly grounded grounding-type receptacle. Where a 2-prong wall receptacle must be replaced with a properly receptacle installed in accordance Electrical Code and local codes is encountered, it grounded 3-prong with the National and ordinances. 12 ,MIwrong should be perk)farted b_ a quahfied elecmoan 13 blake certam that the power source conforms to the requirements ot your equipment 14.Protect electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Replace or repair damaged or worn cords immediately. 15. Do not touch an operating motor. Modern signed to operate at high temperatures. motors are de- 16. Do not handle a pump or pump motor with wet hands or when standing on a wet or damp surface, or in water. I_.WARNING] Risk of electric shock. If your basement has water or moisture on the floor, do not walk on wet area until all power has been turned off. If shut-off box is in basement, call the electric company to shutoff service to the house, or call your local fire department for instructions. Remove pump and repair or replace. Failure to follow this warning can result in fatal electrical shock. INSTALLATION [AWARNINGIDo ways not use power _ord to lift motor. ELECTRICAL CONNECTIONS The Pump has a 3-prong electric plug. The third prong is used to ground the pump to prevent possible fatal shock. The third prong should never be removed. Your electrical outlet should be the 3-prong, polarized type with an internal ground. A separate 15 amp GFCI branch electrical circuit mended. DO NOT USE AN EXTENSION CORD. is recom- Testing for Ground For your safety, check your outlet for ground using a Circuit Analyzer. (Figure A). A Circuit Analyzer will tell you by a pattern of lights if the power, neutral, and ground wires are correctly connected to your outlet. It can also be used to check other outlets in your home. A Circuit Analyzer is available in the Sears Electrical Department. Al- use handle. NOTICE: or fish. Do not use this pump in ponds containing plants 1. Pump should be located and should rest on level solid foundation. Do not suspend pump by means of discharge pipe or power cord. Keep pump inlet screen clear. 2. Thread outlet pipe into pump body carefully to avoid stripping or crossing threads. a. To install with 3/4" garden hose, install adapter pro- UL Listed Analyzer Figure Outlet / A vided with pump. Face Plate b. To install with rigid pipe, use plastic pipe. Wrap thread with Teflon tape or use Plasto Joint Stik*. Screw pipe into pump hand tight +1 - 1-1/2 turns. NOTICE: Do not try to disassemble moving inlet screen. Any evidence warranty. pump farther than reof tampering will void 3. Power Supply: Pump is designed for 115V, 60 Hz operation and requires a circuit of 15 amperes or more capacity. It is supplied with a 3-wire cord set with grounding-type plug for use in a 3-wire, grounded outlet. 3 wire extension cord, of at least 14 AWG (2mm 2) size is suggested, with larger sizes for runs over 25 ft (7M). safety, pump should always be electrically grounded suitable electrical ground such as a grounded water or a properly grnunded metallic raceway, or ground system. Do not cut off the round grounding prong. For tn a pipe wire [_WARNING]The pump motor is equipped with automatic resetting thermal protector and may restart unexpectedly. ProtectDr tripping is indication of motor overloading as a result of operating pump at low heads (low discharge restriction), excessively high or low voltage, inadequate wiring, incorrect motor connections, or a defective motor or pump. *Lake Chemical Co, Chicago, IL Outlet Outlet Box Face Plate Screw to Cold Water Pipe 6530993 Figure B No. 4 Wire Clamp Clamp Metal Water Pipe Meter 655 0993 Figure C Grounding OPERATION Outlet If your outlet is not grounded, install a copper wire, at least 14 gauge (2mmr), from the outlet box, as shown in Figure B, to a metal cold water pipe. Use ground clamp on pipe. [_WARNINGJRisk of electric shock. Do not handle pump or pump motor with wet hands or when standing on wet or damp surface, or in water. IMPORTANT: The cold water pipe you use as a ground must have metal continuity to electrical ground. If continuity is interrupted by plastic, rubber, or other electrical insulators; such as hoses, fittings, washers or gaskets (including water meter or pump), a metal bypass must be used. Any electrically insulated connector should be jumped (as shown in Figure C), with a length of No. 4 wire clamped securely at both ends. NOTICE: or fish. Automatic Thermal Overload Protection This pump motor has a buih:m automatic thermal overload protector. If the motor overheats, the protector will open and cut off power to the motor before the heat damages it internally. The overload will reset automatically and the pump will restart after the pum_ cools down below the danger point. [_,WARNING ]DO NOT attempt to work on the pump or motor if the overload seems to have tripped. The motor may restart without warning at any time. You could be injured and the pump damaged if it starts when you are working on it. DO NOT attempt to repair a non-operational sump Take it to Sears for service by a qualified technician. Generator pump. Sizing Below is the minimum Engine-Generator Watt rating required to power this pump motor. Any additional loads, such as lights, must be added to the listed load and the geno orator sized accordingly. Pump Motor HP Minimum Watt Rating of Generator 1/6 1/4 3000 320O Do not use this pump in ponds containing plants 1. Shaft seal depends on water for lubrication. Do not operate pump unless it is in at Mast 3/16" (4.75mm) of water as seal may be damaged if allowed to run dry. 2. Motor is equipped with automatic reset thermal protector. If temperature in motor should rise unduly, switch will cut off all power before damage can be done to motor. When motor has cooled sufficiently, switch will reset automatically and restart motor. If protector trips repeatedly, pump should be checked as to cause of difficulty. Low voltage, long extension cords, clogged impeller, very low head or lift, etc., could cause cycling. 3. Pump will pump water down to 3/16" (4.75mm); this means that it will not remove all water. If unit has been operating and suddenly no water comes out of discharge hose, shut off unit immediately. Water level is probably very low and unit has broken prime. Use mop or squeegee to remove remaining water. [ _,WARNING I Risk of electric shock. Before attempt- ing to check why unit has stopped operating, disconnect power from unit. Do not handle pump with wet hands or when standing on wet or damp surfaces, or in water. Failure to follow precaution can result in personal injury and/or property darnage. Airlocks When a pump airlocks, it runs but does not move any water. An airlock will cause the pump to overheat and fail. This pump has an anti-airlock hole in the bottom of the pump body (see Page 7). If you suspect an airlock, unplug the pump, clean out the anti-airlock hole with a paper clip or piece of wire, and restart pump. IMPORTANT: This hole allows the pump to start priming within 15 seconds in as little as 1/2" of water. NEVER restart pump in less than 1/2" of water. Leakage from the anti-airlock hole is normal. SERVICE MAINTENANCE Make certain that the pump is unplugged before attempting to service or remove any component. 1. The motor in the unit is sealed in oil. No additional lubrication is necessary. 2. IMPORTANT: Disassembly of the motor assembly will void the warranty. It might also cause internal leakage and damage to the unit. If repairs are required, return the pump to the dealer from whom it was purchased. 3. Inlet screen objects. Pump should be kept clean and free of all foreign Cleaning NOTICE: Attempting warranty. to disassemble motor will void the 1. Disconnect power cord from electrical outlet before working on pump. The volute screen and shield may be removed to replace impeller o_"clean pump of mud or debris. General IAWARNING]Rtsk of electric pump always disconnect and remove pump electric 1. If pump shock. When servicing power to electrical cord from outlet. outlet does not operate: a. Check for loose plug at electric outlet. b. Check for blown fuses or tripped fuse box/circuit breaker box. circuit breakers at c. If a and b above check OK, plug in a light that you know works. If it lights, take your pump to Sears for service. If it doesn't light, the electrical circuit is fattlty; consult a licensed electrician. 2. Pump starts, but blows fuses/trips circuit breakers: After disconnecting power to pump, remove the screen and shield from the bottom of the pump and make sure that the impeller turns freely. Remove any debris obstructing impeller. If pump still does not operate correctly, return it to your nearest Sears Service Department for repairs. 3. Pump runs, but does not empty a. Clean pump intake sump: screen. b. Water may be entering discharge it. sump faster than the pump can c. Be sure vertical distance from pump discharge outlet to discharge pipe outlet is 20 feet (6M) or less for Model 390.269451, and 22-1/2 feet (6.9M) or less for Model 390.269551. d. Be sure discharge e. Unplug pump. pump. pipe is not plugged Clean out anti-airlock or frozen. hole. Restart PUMP PERFORMANCE Discharge Height in Feet Above Pumping Level HP 3' 5' 10' 15' 20' 390.269451 1/8 26.0 25.0 21.5 17.5 11.0 390.269551 1/4 30.0 28.5 24.5 20.0 14.5 Model For maximum GARDEN performance, purchase HOSE Sump/Utility GPM Hose Kit, SEARS Stock No. 27909. PERFORMANCE Model No. 390.269451 Type of Hose Length of " Hose 1/2" HOSE 518" HOSE VerticalPumpingDi_ance 3' 5' 10' 15' 20' 25' 8.5 8.2 7.0 5.7 4.3 50' 6.1 5.8 5.1 4.3 3,0 75' 5.0 4.8 4,4 3.5 2.4 100' 4.5 4.3 3.6 2.9 1.7 25' 11.4 10.8 9.2 7.4 5.1 50' 8.6 8.3 6,9 5.6 4.0 75' 7.0 6.6 5.7 4,6 3.1 100' 6.1 5.9 5,0 4.2 2.9 10' 15' 20' Model No. 390.269551 Type of Hose Length of Hose 1_" HOSE _8" HOSE Performance shown Vertical Pumping Distance 3 7 5 _ 25' 9.0 8.7 7.5 6.7 5.2 50' 6.8 6.5 5.9 5.0 4.0 75' 5.2 5.0 4.6 3.7 3.1 100' 4.9 4.7 4.3 3.3 2,9 25' 12.3 11.7 10.3 8.9 6.8 50' 9.0 8.7 7.6 6.5 4.9 75' 7.2 7.0 6.4 5.4 4,1 100' 6.4 6.2 5.5 4.9 3.8 in gallons per minute. 6 REPAIR PARTS Antt-Atrlock Hole O .4__----- 3 Repair Parts Model Number Part Description Key No. Qty. 399.269451 1/6 HP 390.269551 114 HP PS117-54-TSU PS117-51-TSU 1 Power Cord 1 2 Motor 1 3 1 1 PS5-24P PS5-25P 4 Impeller Shield_ PS70-3P PS70-3P 5 Screen 1 PS8-5P PS8-5P 6 #8 x 5/8 Pan Head Screw 3 Garden Hose Adapter 1 FT0013-43 FT0013-43 • Not dlustrated • If motor fads, replace enttre pump *" Standard hardware item; purchase locally. SEARS OWNER'S MANUAL I:RRFTSMRN° SUBMERSIBLE UTILITY PUMP Model No. 390.269451 390.269551 Forthe repair or replacementpartsyon need Call7 am - 7 pro,7 daysa week 1-800-366-PART (1-800-36g-7278) Forin-homemajorbrandrepair service Call24 hours a day,7 days a week 1-800-4-REPAIR (1-800-473-7247) The model number of your Submersible Utility Pump will be found on the pump label. Forthe locationof a SearsRepairServiceCenterin yourarea Call24 hours a day, 7 days a week 1-800-488-1222 When requesting service or ordering parts, always give the following information: • Product Type • Model Number • Part Number For informationon purchasinga Sears MaintenanceAgreementor to inquire aboutan existingAgreement call 9 am - 5 pm, Monday-Saturday A 1-800-827-6655 SEARS • Part Description America's Repair Specialists Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Apr 04 16:31:30 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools