Craftsman 390291198 User Manual CAPTIVE AIR TANK Manuals And Guides L0409598

CRAFTSMAN Captive Air Tank Hookup Manual L0409598 CRAFTSMAN Captive Air Tank Hookup Owner's Manual, CRAFTSMAN Captive Air Tank Hookup installation guides

User Manual: Craftsman 390291198 390291198 CRAFTSMAN CAPTIVE AIR TANK - Manuals and Guides View the owners manual for your CRAFTSMAN CAPTIVE AIR TANK #390291198. Home:Plumbing Parts:Craftsman Parts:Craftsman CAPTIVE AIR TANK Manual

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

S ARS
OWNER'S
MANUAL

Model No.
390.291198
390.291358
390.291558
390.291658
390.291698
390.291758

CAUTION:
Read and Follow
All Safely Rulesand
Operating Instructions
Before First Use of
ThisProduct.

Save ThisManual For
Future Reference.

CRRFTSMRN°
CAPTIVE AIR ®TANK
• Safety Instructions
• Installation
• Operation
• Service Hints
• Repair Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179
PRINTED

USA

U.S.A.

Form No

F642-9821 (Rev 7/29/04)

READ AND

SAFETY

INSTRUCTIONS!

This is tile safety
alert symbol
When yon sec this symbol on your tank or ill this nlantlal, look for one nf the fol-

h)wing signal words
personal injur_ :

and he alert

the

|_)r

potential

DANGER \V;ll'l/_,
ah()(l[
haz;ll'dS thai will cause seriotls pe]'sonal injury, death or major property
damage
if ignored
WARNING

[ AWARNING

warns

serious personal
ignnr('d.

]

CAUTION
minor

CAUTION

about
injury,

warns

personal

about

injury

hazards

that

death or major

hazards

or Call

will

prnperty

that will

or pn)pert T damage

or can

cause

if ignored.

The label NOTICE indicates
special instructions
important
but not related to hazards.
Carefully
read and follow
this manual
and on tank.

cause

danulge if

all safety

wlaich

instructions

are

Keep safety labels m good condition.
Replace missing or damaged

RULES

FOR SAFE INSTALLATION

AND

sal_ty labels.

OPERATION

1. Read these Rules and the Instructions carefully. Failure
to follow them could cause serious bodily injury and/or
property damage.

NOTICE: Ahhongh No. 2729 Relief Valve is set to open at
75 PSI, lot your safety Captive Air _Tanks are designed and
rated to operate at up to 100 PSI.

AWARNING] These water storage tanks arc designed for
Hazardous
operation on cold well water systems limpressure
ited to a maximum working pressnre of 100
pounds per square inch (PSI). If your water system can exceed 100 P.S.I., install a Sears No. 2729 relief valve on the
system. Failure to follow these instructions can canse tank
blow-up and result in serious injury.

2. Be sure installation meets all local plumbing,
electrical and well codes.

WIZ_NOT

_FJVSE FROM
i_e

,_y

S_t_do

BE LIABLE

PROPERTY
not

4. Before installing or servicing your
pump power source is disconnected.

FOR £OSS OR DAMAGE

DAMAGE

DIRECTLY

the eXClusiOnlof

limitation

LIAB_

TO PROPERTY
OR IND1RECTL
of incidental

OR ANY

pump,

BE SURE

....
INCIDENTAL

OR CONSEQUENTIAL

LOSS OR EX.

y FROM THE USE OF THZS PRODUCE
or consequential

damages,

so the above

limitation

or exclusion

not app_ to you_

_x_i_'SERVIGE
UNITED ST)I'TES.
_s

alo_

3. Always test water from well for purity before using. Call
your local health department for testing procedure.

LIMITATION

.....
__

pnmp,

warranty

THE NEAREST
SEARS SERVICE CENTER/DFaPARTMEIVT
YOUR LOCAL SEARS SERVICE CENTER OR STORE.

IS AVAILABLE
BY SIMPLY CONTACTING
FOR SERVICE OUTSIDE THE {LS.A., CONTACT

gives you specific

legal rights,

Sears, Roebuck

and you may also have other
and Co., Dept.

817 WA,

tights

which

Hoffman

vary from state

Estates,

IL 60179

to state.

IN TI_

CONTENTS
WARRAN'I_'

INTRODUCTION

...................................................

SAFETY ............................................................................

INSTAI+I+ATION...........................................................

3-6

Please read our instructions before yon install and use your
tank. This will help you obtain full benefits ti'om this tank.
It will also help you avoid needless service expense that
resuh
our

()IWRATION ....................................................................

cannot

control

cannot

cover

lfl-l 1

BASIC TOOLS

AND MATERIALS

NEEDED

INSTALLATIONS
TOOLS

MATERIALS

Pipe Wrenches

Plastic Pipe and Fittings (as required

Screwdriver

Teflon Tape (DO NOT use pipe joint compound

Knife or Saw to Cut Plastic Pipe
Tire Pressure

GALVANIZED

aild

7-9

REPAIR PARTS ...........................................................

PIPE

catlses

SERVI('E HINTS ............................................................

PLASTIC

from

\¥a rrailt y+

to complete

job).
on

plastic fittings) or Plasto-Joint Stik*

Gauge

STEEL PIPE INSTALLATIONS
TOOLS

HATERIALS

Pipe Wrenches
Screwdrivers

Galvanized

Pipe Joint Compound

Pipe Cutting and Threading
Tire Pressure

Pipe and Fittings (as required

to complete

job).

or Teflon tape

Tools

Gauge

INSTALLATION
+_WARNINt If your system can develop more than 100
Hazardous
PSI pressure, install a Sears No. 2729 relief
pressure
valve in system to prevent possibility of
tank blow-up.

Standard pipe fittings, such as nipples, tees and elbows
must be purchased locally. If you are using a horizontal jet
pump mounted on top of tank, Figures 5 and 6, Kit No.
2788 is required. See Page 10 for contents of kit.

NOTICE:
DO NOT use any type
water on Hose to Plastic fittings.

of lubricant

than

If your present system has an air volume control (AVC), remove it and plug AVC port on pump.

ff rigid piping is installed
to support
the piping.

on inlet flange,

BE SURE

Complete
pump,
tank, and piping system MUST be protected against below freezing
temperature.
Failure to do
so could cause severe damage
and voids the warranty.

to elbow

other

For proper installation of your pump to tank, follow one
of the typical installations on Page 4 and 5. Use Teflon tape
on all threaded connections
to tank.

* Lake Chemical

Co., Chicago,

Illinois.

Priming

Priming Plug,
Priming Tee
(User Supplied}

Priming
..

(User

Plug,
Tee
Supplied)
To Service

FIGURE
I - Typical Installation: Shallow Well Jet
On Horizontal Tank. To Mount Pump To Tank,

FIGURE 2 - Typical Installation: Deep Well Jet On
Horizontal Tank. To Mount Pump To Tank,

Purchase Tank Fittings Kit 2788.

1" x 3/4" Reducer
Supplied)

Supplied}

From
Fgom

Well

Wel_

To SerVice

To Se_ic(

FIGURE 3 - 2 Gallon Tank Mounted
Shallow Well Jet Pump

FIGURE

Above

4 - 2 Gallon Tank Mounted

Above

Deep Well Jet Pump
pnming
pnrning

priming Plug,
pNmingTee
(UserSupplied)

Plug,
T6_

(U ser Supolied)

To Service

FrOm
Well

FIGURE

5 - Vertical

Tank With

FIGURE

Shallow Well Jet

Pump

Pump
4

6 - Vertical

Tank With

Deep Well Jet

INSTALLATION
50 and 85 gallon tanks are
not equipped with mntmting bracket.
Install pump beside tank as sbo\vn
NOTICE: When using plastic fitting or
installing a plastic pump, use only
Teflon tape or Plasto-Joint Stik on male
threads.
1"-

1" x 1" Tee

2* - 1" Nipple
3* - 1-1/4" X 1" Reducer
Required
for 50 and 85
gallon
tanks.

Bushing

*Not furnished
- must be
purchased
locally
"_""

Pressure

Pump To Tank FiRings
Package
Not Furnished
With Tank,
Purchase
Kit Stock No. 2788
From Your Sears Store.

Regulator
1" Disohar(

2358b 0697

FIGURE

6 - 19, 36, 50 and 85 Gallon Tanks With

Multi-Stage

Pumps

TANK
Electrical
Disconnect
Switch (All _"_Installations)

SIZES

19 GALLON
36 GALLON
50 GALLON**

Control Center
(3-Wire Pump
Only)
_-_,

85 GALLON**

I
LAWARNING
j] High capacity pumps
should be used with the 50 or 85
gallon tank only.

Cable for Two-Wire
Pum
from Pressure
Switch to Motor

** 1-1/4" to 1" reducer
for 1" piping.
To Pump
Motor

Stock No. 2722

FIGURE

Tanks With

High Capacity

Relief Valve,

Sears Stock
No. 2729

Or Residential
5

Size Submersible

required

Relief Valve (No. 2729)

must be purchased

.Pressure Gauge,
Sears Stock
No. 2768

Submersible Purr
Manifold, Sears

Note:

Guardsearsll
Stock
No.
2721

From Well

Not
to
2391 0496A

Pressure Switch,
Sears Stock No.
2782 or

"-k

[ NOTIOE:
Installthan
relief I
valve
nottank.
more
24"
from

Scs_e

Pumps

separately.

I NSTALLATION
If your system
can develop
more
than
100 PSI pressure,
install
a Sears
No.
2729 relieve
valve in system
to prevent
possibility
of tank blow Ul).

_kWARNIN(
Hazardous
pressure

(_apdve Air Tanks can be connected
together to increase
the SUl'q'_l} of usable water (dntv_'down).
Two tanks of the
same size \\ill double the suppl 3 and three tanks will triple
thc SUl_p[ } See Figtlres 8 and _) l_)r t} pleat illstallaliolaS

NOTICE: All (;apfixe Air "lhnks except Models 391) 291 I_;N
and 390.291358
are designed to operate ill tile vertical
pusititm.

\\ hell tlSJl)_ a _,tiblliersiblc
ptinlp, the iI]allil_>ld and sxvilch
assembly must lye installed in the pipe lille as close to tile
center of the tanks as possible.
See Figures 8 and 9.

The tank is shipped from tile l_tctury with a pre charge nf
air. This system DOES NO'I' require the use of an 3' outside
air charging devices such as ;tit- volume controls on jet
pumps, or bleeder orifices on suhmersible puml)s.

Tanks

From
Well

To
Service

Froml
Well

To
Service

Pressure Switch and 27229
Relief Valve Location When

Pressure Switch and 27229

Using Submersible

FIGURE

Relief Valve Location When

Pump

FIGURE

Pump

OPERATION
BEFORE
Your tank

YOU

START

is facto W charged

YOUR
with

PUMP

forty (40)

pounds

of air

NOTICE:
For years of trouble
free service,
check
precharge annually. See service hints (Page 7) for procedure.

pressure.
To determine
pressure
switch setting, see pump
owner's
manual.
If your pump pressure
switch
cut-in setting is less than forty (40) pounds,
the tank air pressure
MUST be reduced
to this cut-in pressure
switch
setting
(see table). To do this, bleed air from the valve located on

NOTICE:

top of the tank. Check pressure
frequently
with an accurate tire pressure
gauge until correct
pressure
has been
reached.
Conventional
pump
pressure
pumps are as follows:
CUT IN/CUT

OFF

switch

settings

PSI

20 PSI

30/50

PSI

30 PSI

40/60

PSI

40 PSI

and

expel

all air out of the

pump to run until there is a steady
()pen and close faucets repeatedly
has been removed.

SEARS

PRECHARGE

20/40

Release

piping

sys-

tem and the water reservoir
portion
of the Captive Air®
Tank. This is required
on new installations,
pumps requiring repriming
and pumps that have been apart for service.
To accomplish
this, open faucets farthest
away from tank
and start the pump.
Observe
the sputtering
water flow
from faucets.
This is a mixture
of air and water. Allow
air free stream of water.
until you are sure all air

If air continues to remain in system, check for leaks in piping on suction side of pump system (Jet Pumps Only).
If yuu have a submersible pump, remove the bleeder orifices in the pipe (just below the well seal) and replace
bleeder orifice with pipe plugs.

OPERATION

Tank is nearly empty:
Water storage bag is at bottom. Air expands to fill space
above bag. The pump starts

FIGURE

Water starts to fill the bag:
As bag fills, air above the
bag is compressed,

Bag is full to capacity:
Air is compressed to the
utmost for maximum drawdown. The pump stops

Water is being drawn
from the bag:
Compressed air in the
tank forces water out.

SERVICE
NOTICE: To prevent
annually.
TO CHECK

TANK

waterlogging,

check tank air charge

HINTS
TO CHECK

PUMP

PRESSURE

SWITCH

1. Start the pump and allow the pressure
off.

AIR CHARGE

If dmwdown (amount of water that comes out of tank per
pump cycle) decreases significantl}; check as follows:
1. Check
pump,

air charge in tank. Shut off electric power
open faucet near tank, and drain completely.

2. At the air valve in top of tank, check air pressure with
standard tire pressure gauge. Air pressure should bc the
same as pump pressure switch cut-in setting.
3. If the air pressure is below the cut-in setting, add air to
the tank. Use an air compressor or a portable air storage
tank.

switch to shut it

2. Check the tank air pressure with the tire gauge. It should
be the same as the cut-off pressure tbr your system. (See
"OPERATION" section on Page 6 for correct pressures).
3. If the pressure reading is different from your system recommended pressure, the switch should be replaced.
REPLACEMENT

OF AIR VALVE

If air valve hecomes broken, or leaks beyond repair, it may
be necessary to replace it.

4. Use soap or liquid detergent
to check for air leaks
around air valve. Continuous bubbling indicates a leak.
If necessary, install new core in air valve. This is the same
as those used for automobile tubeless tires.

Groove

1449 0195

Remove nuts
J ( 6 Places)

FIGURE

It is a standard tubeless tire valve which snaps in position
in groove as it is pulled up thru hole from inside tank.
1. Disconnect

power to pump.

2. Relieve (drain) ALL water
closest to tank.

in system by opening

faucet

14480195

3. Relieve (expel) ALL air pressure
core from inside of valve.
FIGURE

4. Disconnect

in tank by removing

outside piping only to tank.

SERVICE
5. With sharp knife, cut off stem as close to tank
sible. Push remaining
portion
into tank.

as pos-

TESTING

FOR

1. l)iscnnnect

6. Lay tank on side and remove six (6) nuts from studs. Tap
cover to break seal add remove
cover assetnl_ly Iroln
tallk. You cat1 flow set tilt: villyl bag. Scc Figure I I

LEAKAGE

OF VINYL

BAG

pnwcr tu pump.

2. Relieve (drain) ALl. water in system by opening
closest

lancet

1o tatlk

3. Relieve (expel) AH air pressure
core l]'om inside of air valve.

7. Before removing vinyl bag from grnove scat in tank. BF.
SURE all water is drained fi'om bag This can be ac
complished
by tipping tank upright anti allowing remaining water to drain.
8. Carefully remove lip portion
and push bag into tank.

HINTS

4. Disconnect

in tank by removing

outside piping nnly to tank.

5. Turn tank upside down.

of bag from grnove seat

NOTICE: BE CAREFUL not to damage air valve when
tipping tank. Remnval of air valve is not required. If
water leaks nut of the wtlve core opening, the vinyl bag
has a hole in it and nlust be replaced.

9. Block up tank as shown in Figure 13. This will allow
cut off portion of stem to slide down to bottom of tank.
Reach in around bag until you find it and remove it.

PROCEDURE
BAG

FOR

REPLACING

VINYL

Be sure all air has been expelled
before removing nuts.
FOR

6, 19 AND

36 GALLON

from tank

TANKS

1. Carefully lay tank nn its side.

sl!des to the bottom of tank

2. Remove nuts around cover plate.
to retrieve stem

FIGURE

3. Tap cover to break the seal and remove cover assembly
from tank. You can now see the vinyl bag.
4. Bag cannot be removed in one piece. Wherever convenient, grip bag with pliers and pull outward. At the
same time cut bag with sharp knife or single-edged
razor blade. Continue pulling and cutting until bag is
completely removed.

10. Wipe a thin film of soapy solution on top half of replacement stem and insert in stem hole in top of tank.
It is necessary to use a valve stem pulling tool to pull
stem thru opening. This toni is the same as used by
your local filling station and Sears Automotive Center
when servicing tubeless tires.

5. Clean and dry inside of tank.
NOTICE: Before replacement bag can be inserted
it must be tightly rolled up as follows:
1. Place bag on clean surface with opening
3. Tightly roll bag towards center

CAUTION

] It is important

that nuts be tightened

5. Finish rolling bag.
6. As an aid for inserting bag in tank, sprinkle outside with
talcum powder.

follows: First, hand tighten all nuts. Then tighten one
nut to a snug fit. Next, tighten the one opposite to a
snug fit. Proceed, tightening the others in opposite
pairs to a snug fit. Recheck all nuts in same opposite
patterns to be sure they are evenly tightened and you
have a good seal. DO NOT overtighten,
as you may
twist the studs off the tank. With a torque wrench,
tighten to 85 inch pounds.
14. Tip tank upright and assemble
15. Recharge

tank with proper

opening.

4. Before center opening is covered up, force air out of remalning portion of bag.

and place on

13. Hand tighten all nuts on studs.
[_

up.

2. Flatten bag and force air out.

11. Pull neck of bag out of tank opening and seat in groove.
BE SURE ring groove is clean.
12. Clean sealing surface of cover assembly
studs.

in tank,

7. With tank upside
tank.

down,

push tightly rolled bag into

8. Put your arm in bag and push sidewalls outward.
NOT important that all wrinkles be removed.

It is

9. Clean flange ring and groove of tank.
10. Pull lip of bag through

tank opening

and place in ring

groove.

11. MAKE SURE it seals properly

for operation.

12. Clean sealing surface
studs.

amount of air.

of cover

in groove.
assembly and place on

SERVICE
13. hlstall nuts and washers

(m studs, ltand tighten all nuts.

,&.CAUTION It is inlportam
that nuts he tightened as
fi)llows: First, hand tighten all mils. Then tighten one
rail Io a snug 1][ Next. tighten the one opposite to a
Siltlg I:il Proceed, tightening the _thcrs in opposite
pah-s lo a suug lit, Recheck ;ill ntltS in SalUe opposite
patterns
to lie sure
they arc i.-v,qlly
tightened and you
have a good seal. DO NOT overtighten,
as you may
twist the studs off the tank. With a torque wrench,
tighten to 85 inch pounds.
14. Tip tank upright and reassemble
15. Recharge
FOR

tank with proper

SO AND

_,WARNINq
Hazardous
pressure

R_r openltion.

amount of air.

85 GALLON

TANKS

Be sure all air has been expelled
before removing nuts.

from tank

1. Carefully lay tank on its side.
2. Remove nuts around cover plate.
3. Tap cover to break the seal and remove cover assembly
from tank. You can now see the vinyl bag.
4. Bag cannot be removed in one piece. Wherever convenient, grip bag with pliers and pull outward. At the
same time cut bag with sharp knife or single-edged
razor blade. Continue pulling and cutting until bag is
completely removed.
5. Clean and dry inside of tank.
6. Place hag on its side on dry clean surface.
7. Flatten bag and force air out.
8. Starting on one side, tightly roll bag to other side.
NOTICE: Before opening
maining air out.

is rolled

closed,

force re-

9. Finish rolling bag.
10. As a aid for inserting bag in tank, sprinkle
talcum powder.

outside with

11. With tank on its side, push tightly rolled bag into tank
opening.
NOTICE: Push bag in tank only the length of the roiled
bag.
12. Insert arm in bag and push sidewalls outward.
important that all wrinkles be removed.

It is NOT

13. Clean flange ring and groove to tank.
NOTICE:
steps:

Two people

are required

for the following

14. Holding the bag, stand tank open end up.
NOTICE: DO NOT damage air valve. It may be of help
to lean tank in corner.
15. Pull lip ring of bag through
ring groove.

tank opening

and place in

HINTS
16. MAKE SURE it seats pruperly
17. (]lean
studs.

sealing

surface

of cover

IN hlstallllulSal/d\vashcrsolaStUdS

in groove.
assembly

and

place

oil

Ilatldliglltcn;illlltllS

NOTICE: It is hnportaut
that mils bc tightened
:is lol
lows; First, hand tighten all uuts. Tllen tighlc, il uric nut
to a suug fit. Next, tighten the one opposite
to a Slltlg
fit. Proceed,
tightening
the others in opposite
pairs to
a snug fit. Recheck
all nuts in same opposite
patterns
to be sure they arc evenly tightened
and you have a
good seal. DO NOT overtightcn,
as you may twist the
studs off the tank. With a torque wrench,
tighten to 85
inch pounds.

19. Tip tank upright and reassemble for opcmtiun.
20. Recharge tank with proper amount of air.

PUMP

TO TANK

FITTINGS

Pump to tank fittings Package No. 2788 is not furnished.
You may purchase
it at your local Sears Store.

PACKAGE
Required
low/deep

NO. 2788

to install all SEARS Captive
well jet pump.

REPAIR
KEY
NO.

O--6

Air' Tanks

with

PARTS

PART
NO.

PART
DESCRIPTION

U78-777PA

2
3

U78-770P
U74-37J

Adapter * 1" NPT (Male) by 1" Insert (2 Req.)
Elbow - 3/4" NPT (Male) by 1" Insert
Hose

U19-55SS

Clamp - Hose (2 Req.)

U30-701ZP

Bolt - 3/8" - 16 x 1-3/4" Lg. (2 Req.)

U43-62ZP

Flat Washer - 3/8" (2 Req.)

U43-12ZP

Lock Washer - 3/8" (2 Req.)

U36-38ZP

Nut - Hex 3/8" - 16 (2 Req.)

U78-769P

Elbow - 1" NPT (Male) by 1" Insert (2 Req.)

CAPTIVE
(6 GALLON)
(19 GALLON)

shal-

AIR ®TANK
MODEL
MODEL

390.291198
390.291358

REPAIR PARTS

KEY
NO.

MODEL
390.291198
PART NO.

MODEL
390.291358
PART NO.

U20-7

U20-13

U31-442P

1A
2

U36-202BTI"

3
3

PART
DESCRIPTION
Bag - Vinyl
Inlet Flange

U31-446P

Inlet Flange

U36-202BTt
U78-777PA

Nut 5/16 - 18 Hex (6 Req.)

U78-77OP

Adapter 1" NPT Male
Elbow - 3/4" NPT

(Male) by 1" Insert
U212-160t

U212-160t

Air Valve w/Cap

• Not Illustrated.
t Standard hardware item, may be purchased locally.

CAPTIVE

AIR ®TANK

MODEL

390.291558

(I 9 GALLON)

MODEL

390.291698

(50 GALLON)

MODEL

390.291658

(36 GALLON)

MODEL

390.291758

(85 GALLON)

NOTICE:

50 and 85 gallon

tanks

are not equipped
with mounting
bracket.
Install pump beside tank
as shown
on Page 5.

REPAIR
Key
No.

PARTS

390.291558
19 Gallon
Tank

390.291658
36 Gallon
Tank

390.291698
50 Gallon
Tank

390.291758
85 Gallon
Tank

Part
Description

U20-8

U20-9

U20-10

U20-14

Bag - Vinyl

U31-446P

U31-447P

Inlet Flange

U36-202BT t

U36-202BTT

U36-202BTf

U36-202BTt

Nut - 5/16 - 18 Hex. (6 Req.)

U212-160t

Air Valve w/cap

tStandard

hardware item, may be purchased locally.

Toorderparts,call:
Sears Produ_ Service
I 800 366_7278
11

SE /,4RS
I:RRFTSMgN °
OWNER'S
MANUAL

CAPTIVE AIR ®TANK

Model No.
390.291198
390.291358
390.291558
390.291658
390.291698
390.291 758

Forthe repair or replacementpartsyou need
Call7 am - 7 pro,7 days a week

1-800-366-PART
(1-800-366-7278)

For in-homemajorbrandrepairservice
Call24 hoursa day, 7 daysa week

1-800-4-REPAIR
(1-800-473-7247)

The model number of
your Captive Air _ Tank
will be found on a label
attached to the tank.
When requesting service
or ordering parts, always
give the following
information:
• Product Type
• Model Number
• Part Number
• Part Description

Forthe locationof a
SearsRepairServiceCenterin yourarea
Call24 hours a day,7 daysa week

1-800-488-1222

Forinformationon purchasinga Sears
MaintenanceAgreementor to inquire
aboutan existingAgreement
call 9 am - 5 pm, Monday-Saturday

1-800-827-6655

SEARS
tt:l;t,rl;t_'!:lttV/[g;_
AiTtedca_

Repair Specialists

Sears, Roebuck and Co., Hoffman Estates, IL 60179

U.S.A.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 12
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Tue Apr 03 20:19:04 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 390291198 User Manual CAPTIVE AIR TANK Manuals And Guides L0409598

CRAFTSMAN Captive Air Tank Hookup Manual L0409598 CRAFTSMAN Captive Air Tank Hookup Owner's Manual, CRAFTSMAN Captive Air Tank Hookup installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation