Craftsman 4861992 User Manual BROADCAST SPREADER Manuals And Guides L0503109

CRAFTSMAN Spreader Manual L0503109 CRAFTSMAN Spreader Owner's Manual, CRAFTSMAN Spreader installation guides

User Manual: Craftsman 4861992 4861992 CRAFTSMAN BROADCAST SPREADER - Manuals and Guides View the owners manual for your CRAFTSMAN BROADCAST SPREADER #4861992. Home:Farm Equipment Parts:Craftsman Parts:Craftsman BROADCAST SPREADER Manual

Open the PDF directly: View PDF PDF.
Page Count: 4

Owner's ManuaJ
®
ModeJ No, 486.1992
CAUTION:
Before using this product,
read this manual and follow
all Safety Rutes and
Operating Instructions.
mMPORTANT- READ'THiS FIRST!!!
For Missing Parts or AssembUy Questions
PUease Call 866-576-8388
Mon.-Fd. 7 am -5 pm CST.
FAX 217-728-2032 or e-maiU info@agri-fab.com
Missing parts will be sent UPS in 24 hours directly to your home.
,, Safety
,, Assembly
,, Operation
,, Maintenance
,, Parts
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www, sears,com/craftsman
PRINTED IN MEXICO FORM NO. 49687 (12/04)
RULES FOR SAFE OPERATION
The following safety precautions are suggested. This
broadcast spreader is designed, engineered and tested
to offer reasonably safe and effective service, provided it
is operated in strict accordance with these instructions.
Failure to do so may result in personal injury. Always
observe the rules of safe operation.
1. Do not allow anyone to operate the spreader without
proper instructions.
2. Do not permit children to operate the spreader.
3. Wear eye and hand protection when handling and
when applying lawn or garden chemicals.
4. Read the labe! instructions and cautions for handling
and applying the chemicals purchased for spreading.
5. Keep all nuts, bolts and screws tight to be sure
equipment is in safe working condition.
6. Follow maintenance and lubrication instructions as
outlined in this manual.
FLOW CONTROL LEVER _.______
ADJUSTABLE STOP
1)
ADJUSTING THE FLOW RATE SETTING
1. Loosen the wing nut that fastens the control to the
handle.
2. Slide the Adjustable stop to the desired setting and
retighten the wing nut.
HOW TO USE YOUR SPREADER
1. Pivot the handle up into the operating position and
tighten the two wing nuts.
2. This unit will cover a 4 to 8 foot wide area depending
on the material used and walking the speed of user.
3. Check the listing on the material package or in the
Recommended Spreader Settings instruction sheet
for the proper spreader setting and application rate.
4. Before filling the spreader, push the control lever to
the "OFF" position.
5. Move spreader onto a flat surface - either a walk or a
driveway - and fil!.
6 Slide the Adjustable Stop to the desired setting.
7. Start the spreader in motion, then move the control
lever forward against the adjustable stop to begin
spreading.
NOTE: Always place control lever in the "OFF" position
while filling spreader and when stopping or turning to
prevent excess fertilizer from being released.
APPLICATION TIPS
1. To avoid misses or striping, make each pass about
5 feet from the previous one so some overlapping of
spread pattern does occur.
2. For easiest application, spread across the shortest
edges of lawn first, making two "header" strips for a
turning area, and then spreading between the header
strips. See figure 1.
3. If lawn is odd shaped, spread a border around the
edges and then spread between the border. See
figure 2.
4. Keep wheel approximately 4 feet from any area you
do not wish to spread.
IMPORTANT: Be careful when using spreader around
ornamental plants because weed controls can damage
these plants.
fFIGURE1 _IGURE 2
1. Always empty spreader after each use, storing
leftover material in it's original bag.
2. Wash the spreader and dry thoroughly after each use.
3. Apply a few drops of oi! to all moving parts.
4. Tighten al! nuts and screws before each use.
MODEL 486.1992 PARTS LiST
Item No. Part No. Description Item No. Part No. Description
1 47108
2 44663
3 47109
4 43343
5 47141
6 47112
7 47113
8 46000
9 49335
10 49447
Plastic Leg (2)
Push Nut/Hub Cap (2)
Flow Slide
Hair Cotter Pin
Wing Nut, 1/4-20 (3)
Screw, #10-16 x 1/2" (3)
Washer, Flat ,22" x,78" (2)
Carriage Bolt, 1/4-20 x 1-1/2" (3)
Control Cable Bracket
Contro! Cable Assembly
11 44486
12 47119
13 48001
14 63690
15 47124
16 47137
17 47134
18 47135
19 47136
20 47122
Screw, Hex Head #12 x 3/4" (2)
Leg Brace
Wheel (2)
Axle/Impeller Assembly
Impeller (Included in #63690)
Handle Tube
Pin, Hair Cotter (3)
Washer, 17/32" x 7/8"
Clip, Gear Retainer
Hopper
13
2O
1\
5\
14
18
17
17
13
/
/
/
// 2
10
/
8
® Registered Trademark /TMTrademark of Sears, Roebuck and Co
@ Sears, Roebuck and Co ® Marca Registrada /TM Marca de F4bdca de Sears Roebuck and Co.

Navigation menu