Craftsman 48624540 User Manual 10 TON HYDRAULIC LOG SPLITTER Manuals And Guides L0503120
CRAFTSMAN Log Splitter Manual L0503120 CRAFTSMAN Log Splitter Owner's Manual, CRAFTSMAN Log Splitter installation guides
User Manual: Craftsman 48624540 48624540 CRAFTSMAN 10 TON HYDRAULIC LOG SPLITTER - Manuals and Guides View the owners manual for your CRAFTSMAN 10 TON HYDRAULIC LOG SPLITTER #48624540. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman 10 TON HYDRAULIC LOG SPLITTER Manual
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Owner's Manual CRRFTSHRHI 0 TON HYDRAULIC LOG SPLITTER Model No. 486.24540 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT - READ THIS FIRST!!! For Missing Parts or Assembly Please Call 1-866-576-8388 Questions Mon.-Fri. 7am - 5pm CST. FAX 217-728-2032 or email info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. Sears, Roebuck and Co., Hoffman www.sea rs.com/craftsma n Estates, IL 60179 • • • • • Safety Assembly Operation Maintenance Parts U.S.A. FORM NO. 49668 (2/05) SAFETY RULES CARTON CONTENTS FULL SIZE HARDWARE ASSEMBLY CHART LIMITED ONE YEAR WARRANTY 2 3 4 5 OPERATION MAINTENANCE REPAIR PARTS LIST PARTS ORDERING/SERVICE ON CRAFTSMAN HYDRAULIC 6 6 7 8 LOG SPLITTER For on year from the date of purchase, when this log splitter is maintained an lubricated according to the operating and maintenance instructions in the owner's manual, Sears will repair any defect in material or workmanship free of charge. If this log splitter is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to maintain the equipment according to instructions contained in the owner's manual. WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THE UNITED STATES. IN This warranty applies only while product is in the United States. This warranty gives you the specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179 SAFETY RULES WARNING: When using hydraulic equipment, basic safety precautions should always be followed to reduce the risk of personal injury and hazards due to over pressurization. READ ALL INSTRUCTIONS BEFORE USING THIS TOOL! 1. 2. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations. Don't expose to rain. Keep work area well lit. 3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. 4. STORE IDLE EQUIPMENT. When not in use, log splitter should be stored in a dry location to inhibit rust. 5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool's capacities. 6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not intended. 7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in moving parts. 8. USE EYE AND EAR PROTECTION. WearANSl approved goggles when operating log splitter. 9. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines 10. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. The handles must be kept clean, dry, and free from oil and grease at all times. 11. Keep hands, face and body away from log when it is being split. 2 12. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 13. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. 15. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 2 j3 # PART# DESCRIPTION QTY 1 2 3 4 5 HITCH ASSY HANDLE ASSY LOG SPLITTER AXLE ASSY WHEEL 1 2 1 1 2 65238 65240 65237 65239 46503 z\ 8\ 11\ 12 14 13 17 15 16 \ I0 # PART# 6 7 8 9 10 11 DESCRIPTION 49659 BOLT, HEX MIO x 30 49664 BOLT, HEX M8 x 25 49667 NUT, HEX M8 31917161EWASHER, FLAT 1/2 43003 WASHER, LOCK 3/8 43086 WASHER, LOCK 5/16 QTY 2 4 4 2 2 4 # PART # 12 13 14 15 16 17 49660 43081 43070 43343 23353 43010 DESCRIPTION NUT, HEX MIO WASHER, FLAT 5/16 WASHER, FLAT 3/8 COTTER, HAIRPIN PIN, HITCH COTTER, PIN QTY 2 4 2 1 1 2 10 12 5 / 4 / / 17 /!, Figure 2 13 8 7 Figure 1 ASSEMBLY INSTRUCTIONS Tools Needed: (2) MIO Open End Wrench (2) M8 Open End Wrench (1) Pliers 1. Verify that all parts and all fasteners (Shown full size) on page 4 are included in the carton and parts bag. Refer to page 4 to identify fasteners used in the following instructions. 2. With the Log Splitter(3) standing on end, attach the Hitch Assy(1) using two MIO x 25 Hex Bolts(6), and secure with two 3/8 Washers(14), two 3/8 Lock Washers(lO), and two MIO Hex Nuts(12). Be sure that all bolts are tight. (Figure 1 ) 3. Attach Axle Assy(4) to the Log Splitter(3) using four M8 x 25 Hex Bolts(7), and secure with four 5/16 Washers(13), four 5/16 Lock Washers(11 ), and four M8 Hex Nuts(8). Be sure that all bolts are tight. (Figure 1 ) 4. Slide the Wheel(5) on to the Axle Assy(4) with the long hub facing inwards. Slide a 1/2 Flat Washer(9) onto the outside of the axle. Secure with Cotter Pin(17), bend the ends with a pair of pliers. (Repeat for other wheel) (Figure 2) 5. 6. This Log Splitter will attach and tow behind any standard lawn and garden tractor. Use the supplied Hitch Pin, and Haircotter Pin to attach to tractor. In addition there is a hitch located on the rear of the unit, which allows you to tow a cart behind the Log Splitter. As shown during assembly this unit will stand on its end for easy storage. OPERATION Gather the logs you wish to split. Make sure the maximum length of each log does not exceed 18" If the log does exceed that measurement, you must cut the log to fit the maximum length of the tool. HANDLE RELEASE 2. Make sure the Piston Rod is fully retracted into the cylinder. If necessary, turn the RELEASE SCREW counterclockwise to releaes the hydraulic pressure. Tighten the RELEASE SCREW. 3. Place the log between the Wedge and Piston Assembly. Rest the log in the metal bracket Cradle. 4. Wear eye proctection (goggles) when operating the Hydraulic Log Splitter 5. It is recommended you operate the Log Splitter in the following manner. Stand behind the log splitter and grip one Handle in each hand and pump the Handles in a back-and-forth motion with one Handle fully forward and one fully rearward as shown in figure 3. SCREW / , Repeat Step "5" to advance the Piston Rod forward. This will push the log against the Wedge and Split it. 7. When you have split the log, remove the split pieces. Figure 3 8. Turn the RELEASE SCREW counterclockwise to draw the piston rod back into the cylinder. Tighten the RELEASE SCREW when the piston rod has retracted fully. , When you are done, it is recommended you store your Hydraulic Log Splitter with the RELEASE SCREW opened to relieve any hydraulic pressure during non-use. MAINTENANCE SPECIFICATIONS After every use, wipe down the Hydraulic Log Splitter to remove any tree sap or dirt left behind. This will extend the life of the tool. Maximum Log Length: Ram Stroke: Cradle Dimensions: Base Dimensions: Bleeding The Log Splitter 1. Operate the log splitter to extend the Piston Rod to its maximum length. 2. Remove the Oil Filling Plug. 3. Turn the Release Screw counterclockwise as fast as possible, the Piston Rod will retract and push air from the cylinder out of the Oil Filling Plug. 4. Replace the Oil Filling Plug. Repeat steps 1-4 as necessary. Adding Oil If you should need to add hydraulic oil to the Log Splitter, remove the Oil Filling Plug, and add oil until the oil is 1/2" from top (when laying down). TROUBLE 18" 8-1/16" 3-3/4" x 4" x 4" 42-1/8"L x 8-1/16"W x 37"H SHOOTING If hydraulic cylinder does not move forward when pumping handles. A. Check to see if Release Screw is tightened in the closed position. B. Check to see if you need to add hydraulic oil. 6 REPAIR PARTS FOR HYDRAULIC LOG SPLITTER - MODEL 486.24540 21 22 \ 23 24 \ \ I I / 27 6 / 25 31 -.-........_,, 26 I 18 / 29 30 16 / 5 I 7 # PART # DESCRIPTION 1 65238 Hitch Assembly 4 65239 Axle Assembly 5 46503 Wheel 6 49659 Hex, Bolt MIO x 30 7 49664 Hex, Bolt M8 x 25 8 49667 Hex, Nut M8 9 R19171616 Washer, Axle 10 43003 Washer, Lock 3/8" 11 43086 Washer, Lock 5/16" 12 49660 Hex, Nut MIO 13 43081 Washer, Flat 5/16" 14 43070 Washer, Flat 3/8" 15 43343 Hairpin Cotter 16 23353 Hitch Pin QTY 1 1 2 2 4 4 2 2 4 2 4 2 1 1 # PART # 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 43010 49644 49657 49658 49642 49645 49643 44101 49647 49648 49660 49641 47397 49650 49651 DESCRIPTION Cotter Pin Spring Operating Lever Grip Ram Assembly U-Clamp Jack Top Plate Cotter Pin, 3/32 x 3/4" Spacer Clevis Pin Hex, Nut MIO Frame Handle Clamp Bolt, Hex M5 x 10 Nut, Hex M5 QTY 2 2 2 2 1 1 1 1 1 1 2 1 1 1 1 _ For repair of major brand appliances in your own home... iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii no matter who made it, no matter who sold it! t .... 800 iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii 4 MY HOME SM Anyhme, day or night (1-800-469-4 6m iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii www.sears.com iiiiiiiiiiiiiiiii To bring in products such as vacuums, lawn equipment and electronics ii!i_!i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii!i for repair, call for the location of your nearest Sears Parts & Repair Center. iiiiiiiii:i !iiiiiiiiiiiii 1-800-488-1222 Anytime, dayornight HHHHHHHH_; www.sears.com For the replacement parts, accessories and owner's manuals that you need to do-it-yourself, call Sears PartsDirect SM ! 1-800-366-PART iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii 0 a.m.= 11 p.m. CST, (1-800-366-7278) 7daysaweek iiiiiiiii!iiii!ii!ii!ii!ii!ii!i 1o 800--8276655 iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii 7a.m.=5p.m. CST, Mon.=Sat. iiiiiiii!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiil Para pedir servicio de reparaci6n a domicilio, iiiiiiiii'iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii yparaordenarplezasconentregaadomicilio: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Au Canada pourservice 1-877-LE-FOYER 1-888-SU-HOGARSM (1=877=533-6937) (1=888-784=6427) !i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i !_ SEARS ® Registered Trademark / TMTrademark © Sears, Roebuck and Co en frangais: sM ® Marca Registrada of Sears, Roebuck and Co. / _-MMarca de Fabrica de Sears, Roebuck and Co iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiii_i
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Aug 14 21:03:02 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools