Craftsman 536884582 User Manual 3.0 HP ELECTRIC START SNOW THROWER Manuals And Guides L9050210

CRAFTSMAN Snowthrower, Electric Manual L9050210 CRAFTSMAN Snowthrower, Electric Owner's Manual, CRAFTSMAN Snowthrower, Electric installation guides

User Manual: Craftsman 536884582 536884582 CRAFTSMAN 3.0 HP ELECTRIC START SNOW THROWER - Manuals and Guides View the owners manual for your CRAFTSMAN 3.0 HP ELECTRIC START SNOW THROWER #536884582. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman 3.0 HP ELECTRIC START SNOW THROWER Manual

Open the PDF directly: View PDF PDF.
Page Count: 30

3.0 Horsepower
21 Inch Single Stage
Auger Propelled
SNOW THROWER
Electric Start
MODEL NO.
536.884582
Caution:
Read and follow all Safety
Rules and Operating
Instructions before first use
of this product.
SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A.
761124 08/11/98
Table of Contents 2 Service and Adjustments 12-15
Warranty 2 Storage 16
Safety Rules 2-4 Troubleshooting 17
Contents of Shipping Carton 4 Snow Repair Parts 16.24
Assembly 5 Engine Repair Parts 25-29
OpemUon 6-10 Spanish(Espa_ol) 30-46
Maintenance 11 Parts Ordering/Service Back Cover
LIMITED ONE-YEAR WARRANTY ON CRAFTSMAN SNOW THROWER
For one year from the date of purchase, when this Craftsman Snow Thrower is maintained,
lubricated, and tuned up according to the operating and maintenance instructions in the
owner's manual, Sears will repair, free of charge, any defect in msterial or workmanship. If
this Craftsman Snow Thrower is used for commercial or rental purposes, this warranty ap-
plies for only 90 days from the date of purchase.
This warranty does not cover the following:
•Items which become worn dudng normal use, such as spark plugs, ddve befls and
shear pins.
•Repairs necessary because of operator abuse or negligence, including bent crank-
shafts and the failure to maintain the equipment according to the instructions con-
tained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN SNOW
THROWER TO THE NEAREST SEARS SERVICE CENTEPJDEPARTMENT IN THE
UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN
USE IN THE UNITED STATES.
This warranty gives you specific legal dghts, and you may also have other rights which
may vary from state to state.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179
,Z_ Look for this symbol to point out Important safety precautions. It means_
ATTENTIONIll Become alertlll Your safety is involved.
CAUTION: Always tum key to OFF
position and remove key to prevent
accidental starting when setting-up,
transporting, adjusting or making repairs.
IMPORTANT: Safety standards require
operator presence controls to minimize the
risk of injury. Your snow thrower is
equipped with such controls. Do not attempt
to defeat the function of the operator
)resence control under any circumstances.
A_ California Proposition 65
WARNING:The
engine exhaust from this product
contains chemicals known to the
State of California to cause cancer
birthdefects or other reproductive
harm.
BEFORE USE
•Read the owner's manual carefully. Be
thoroughly familiar with the controls and
the proper use of the snow thrower. Know
how to stop the snow thrower and
disengage the controls quickly.
• Do not operate the snow thrower without
wearing adequate outer garments. Wear
footwear that will improve footing on
slippery surfaces.
•Keep the area of operation clear of all
persons, padicularly small children and
pets.
•Thoroughly inspect the area where the
snow thrower is to be used and remove
all foreign objects.
•Use extension cords and receptacles as
specified by the manufacturer for all snow
throwers with electrib drive motors or with
factory-installed or optional starting
motors.
2
Use only attachments and accessories
approved by the manufacturer of the
snow thrower (such as electric starter kits,
etc.).
•Never operate the snow thrower without
good visibility or light. Always be sure of
your footing, and keep a firm hold on the
handles. Walk; never run.
•This snow thrower is for use on side-
walks, driveways, and other ground level
surfaces. CAUTION: should be exercised
while using on steep sloping surfaces. DO
NOT USE SNOW THROWER ON
SURFACES ABOVE GROUND LEVEL
such as roofs of residences, garages,
porches or other such structures or
buildings.
•Check all bolts at frequent intervals for
proper tightness to be sure the snow
thrower is in safe working condition.
•Disengage clutch before starting the
engine.
•Let engine and snow thrower adjust to
outdoor temperatures before starting to
clear snow.
FUEL SAFETY
•Handle fuel with care; it is highly flam-
mable.
•Use an approved container.
•Check fuel supply before each use,
allowing space for expansion as the heat
of the engine and/or sun can cause fuel to
expand.
•Fill fuel tank outdoors with extreme care.
Never fill fuel tank indoors. Replace fuel
tank cap securely and wipe up spilled
fuel.
• Never remove the fuel tank cap or add
fuel to a running or hot engine.
•Never store fuel or snow thrower with fuel
in the tank inside a building where fumes
may reach an open flame.
OPERATING SAFETY
•Never allow children or young teenagers
to operate the snow thrower. Keep them
away while it is operating. Never allow
adults to operate the snow thrower
without proper instruction.
•Do not operate tt_ismachine if you are
taking drugs or other medication which
can cause drowsiness or affect your
ability to operate this machine.
•Do not use this machine if you are
mentally or physically unable to operate
this machine safely.
•Always wear safety glasses or eye
shields during operation or while perform-
ing an adjustment or repair to protect your
eyes from foreign objects that may be
thrown from the snow thrower.
•Do not put hands or feet near or under
rotating parts. Keep clear of the discharge
opening at all times.
•Exemise extreme caution to avoid slipping
or falling, especially when operating in
reverse or backing up.
•Do not clear snow across the face of
slopes. Excercise caultion when changing
direction on slopes. Do not attempt to
clear steep slopes.
•Never operate the snow thrower without
proper guards, plates, or other safety
protective devices in place.
•Never operate the snow thrower near
glass enclosures, automobiles, window
wells, drop-offs, and the like without
proper adjustment of the snow discharge
angle. Keep children and pets away.
•Never operate the snow thrower at high
transport speeds on slippery surfaces.
Look behind and use care when backing.
•Never direct discharge at bystanders or
allow anyone in front of the snow thrower.
• Do not run the engine indoors, except
when starting the engine and for trans-
porting the snow thrower in or out of the
building. Open the outside doors; exhaust
fumes are dangerous, containing CAR-
BON MONOXIDE, an ODORLESS and
DEADLY GAS.
•Take all possible precautions when
leaving the snow thrower unattended.
Disengage the auger/impeller, stop
engine, and remove key.
•Do not ovedoad the machine capacity by
attempting to clear snow at too fast a rate.
SAFE STORAGE
•Always refer to the owner's manual
instructions for important details if the
snow thrower is to be stored for an
extended period.
•Disengage power to the auger/impeller
when snow thrower is transported or not
in use.
•Never store the snow thrower with fuel in
the fuel tank inside a building where
ignition sources are present such as water
and space heaters, clothes dryers, and
the like. Allow the engine to cool before
storing in any enclosure.
REPAIR/ADJUSTMENTS SAFETY
• After striking a foreign object, stop the
engine (motor). Turn key to OFF position
and remove key to prevent accidental
starting. Thoroughly inspect the
snowthrower for any damage, and repair
the damage before restarting and
operating it.
•If snow thrower should start to vibrate
abnormally, stop engine (motor) and
check immediately for the cause. Vibra-
tion is generally awaming of trouble.
•Stop the engine (motor) whenever you
leave the operating position. Also, turn
key to OFF position and remove key
before unclogging the auger/impeller
housing or discharge chute, and when
making any repairs, adjustments, or
inspections. Remove wire from spark plug
to prevent accidental starting.
•When cleaning, repairing, or inspecting,
make certain the auger/impeller and all
moving parts have stopped.Turn key to
OFF position and remove key to prevent
accidental starting.
•Never attempt to make any adjustments
while the engine is running except when
specifically recommended by the manu-
facturer.
•Maintain or replace safety and instruction
labels, as necessary.
•Run the snow thrower a few minutes after
throwing snow to prevent freeze-up of the
auger/impeller.
Z_ WARNING: This unit is equipped with
an intemst combustion engine and should
not be used on or near any unimproved for-
est-covered, brush-covered or grass-cov-
ered land unless the engine's exhaust sys-
tem is equipped with a spark an'ester meet-
ing applicable local or state laws (if any). If a
spark arrester is used, it should be main-
tained in effective working.order by the op-
erator.
In the state of Califomia the spark arrester is
required by law (Section 4442 of the Califor-
nia Public Resources Code). Other states
may have similar laws. Federal laws apply
on federal lands. A spark arraster/muffler is
available through your nearest Sears Autho-
rized Service Center (See ENGINE REPAIR
PARTS section in this manual).
Contents of Parts Bag
1 - Owner's Manual (not shown)
1 - Parts Bag (not shown)
1-3.2 ounce container 1 - Electric Starter Cord
Craftsman 2-cycle oll 10 ft.
2_ CAUTION: Always wear safety
glasses or eye shields while assembling
snow thrower.
TOOLS REQUIRED FOR ASSEMBLY
1 - Knife to cut carton
The figure to the right shows the snow
thrower completely assembled.
References to the right or left hand side
of the snow thrower are from the viewpoint
of the operator's position behind the unit.
TO REMOVE SNOW THROWER
FROM CARTON
•Locate and remove container of Crafts-
man 2-cycle oil.
•Remove the inserts positioned around the
unit and the packing matedal.
•Cut down two comers nearest the
handles and lay the panel down flat.
•Remove and discard bottom packaging.
•Pull snow thrower out of the carton.
TO ASSEMBLE THE SNOW
THROWER
•Remove wrap on upper handle and along
the side of both handles. Discard wrap.
•Loosen the tee knobs on each side of the
upper handle. See figure on this page.
•Raise the upper handle to the operating
position as shown in figure.
•NOTE: Make sure the cables are not
caught between the upper and lower
handle.
• Check to be sure the clutch cable is not
caught in the handle. Tighten the tee
knobs.
AugerControl
Chute Control
Tee Knob
Chute Deflector
JCHECKLIST
Beforeyou operate your new snow thrower,
toensure that you receive the best perfor-
mance and satisfactionfrom thisquality
product,please review the following
checklist:
,/ All assembly instructions have been
completed.
,/ The discharge chute rotates freely.
/No remaining loose parts in carton.
While learning how to use your snow
thrower, pay extra attention to the following
important items:
// Make sure gas tank is filled with
40:1ratio mixture of gasoline and oil.
,/,/ Become familiar with all controis-thalr
location and function. Operate controls
before starting engine.
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize
yourself with the location of various controls and adjustments. Save this manual for future
reference.
Electric Start IgnitionOff IgnitionOn Oil/Fuel Mixture Primer Button Pushto Engage
ElectricStarter
Auger ControlBar
Chute
Chute
Auger/
'AugerHousing Button
Augel" Control Bar- Starts and stops the
auger which propels the snow thrower.
Chute Control Rod - Changes the direc-
tion of snow discharge.
Chute Deflector - Changes the distance
the snow is thrown.
Discharge Chute - Changes the direction
the snow is thrown.
Ignition Switch Key - Must be inserted
and turned to the ON position to start the
engine.
Choke Control -Used to start a cold en-
gine
Primer Button - Injects fuel directly into the
carburetor manifold for fast starts in cold
weather.
Recoil Starter Handle - Starts the engine
manu_.lly.
Electric Starter Button - Used to start the
engine using the 120V electric starter.
6
HOW TO USE YOUR
SNOW THROWER
TO STOP YOUR SNOW THROWER
•To stop the auger, release the auger
control bar.
NOTE: If the auger continues to creep, refer
(To Adjust Auger Control Cable paragraph on
page 12).
•To stop the engine, turn key to the OFF
position.
TO CONTROL SNOW DISCHARGE
•Turn the chute control rod to set the
direction of the snow throwing.
•Loosen the wing knob on the chute
deflector and move the deflector to set
the distance. Move the deflector (UP) for
more distance, (DOWN) for less distance.
Then tighten the wing knob (See figure
below).
Win Knob
TO USE AUGER PROPEL ACTION
•Squeeze the auger control bar down
against the upper handle to allow the
auger to turn,
•To propel forward, raise the handle to
allow the rubber auger blades to contact
the ground (See figure below). Normal
Operating
Position
Blades 7
be_o CAUTION: Read owners manual
re operating machine. Never direct
discharge toward bystanders. Release the
auger control bar and stop the engine
before unclogging discharge chute or auger
housing and before leaving the machine.
BEFORE STARTING ENGINE
WARNING: Experience indicates that
alcohol blended fuels (called gasohol or
those using ethanol or methanol) can
attract moisture which leads to separation
and formation of acids during storage.
Acidic gas can damage the fuel system of
an engine while in storage. To avoid engine
problems, the fuel system should be
emptied before storage for 30 days or
longer. Start engine and let it run until fuel
lines and carburetor are empty. Use
carburetor bowl drain to empty residual
gasoline from float chamber (See figure in
Storage section, page 16). Use fresh fuel
next season. (See Storage Instructions on
page 16 for additional information).
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
FILL GAS
NOTICE: ENGINES WHICH ARE CERTI-
FIED TO COMPLY WITH CALIFORNIA
AND US EPA EMISSION REGULATIONS
FOR ULGE ENGINES: Are certified to
operate on regular unleaded gasoline.
Include the following emisssion control
system(s): EM, TWC (if so equipped).
Include any user adjustable features -
therefore no other adustments are needed.
The two cycle engine used on this snow
thrower requires a mixtUre of gasoline and
oil for lubrication of the bearings and other
moving parts, The correct fuel mixture ratio
is 40:1 (3.2 oz. oil per gallon of gas - see
Fuel Mixture Chart). Gasoline and oil must
be pre-mixed in a clean gasoline container.
Always use fresh, clean, unleaded gaso-
line.
FUEL MIX CHART (Mixture 40:1)
o,sLo,LiG,slo,,I I I
GASOLINE AND OIL MIXTURE
Mix gasolineand oil as follows:
DO NOT FILL THE FUEL TANK WITH GASOUNE THAT DOES NOT HAVE OIL MIXED IN IT.
SHAKE THE GASOLINE CONTNNER BEFORE EACH FILLING OF THE FUEL TANK.
OII
(1/2cup or3.2 oz.) Shake(;an
1 U.S. gallon container
• Pour 1 U.S. quart of fresh, clean,
unleaded automotive gasoline to agallon
gasoline container.
•Add 3.2 oz of clean, high quality,
Craftsman two-cycle oil into the gasoline
container (One 3.2 ounces of oil pro-
vided).
IMPORTANT: Do not use outboard motor
oil or automobile oils, such as SAE 30 oil,
or multi-viscosity oils, such as 10W-30 or
10W-40.
•Reinstall the cap on the gasoline con-
tainer and shake container vigorously so
the oil mixes with the gasoline
•Add an additional 3 U.S. quads of
gasoline to the gallon container and
shake the container again.
WARNING: Gasoline is flammable and cau-
tion must be used when handling or storing
it. Do not fill fuel tank while snow thrower is
running, hot, or when snow thrower is in an
enclosed area. Keep away from open
flame, electrical spark, and do not smoke
while filling the fuel tank. Never fill fuel tank
completely; but fill the tank to within 114-1/2
inch from the top to provide space for ex-
pansion of fuel. Always fill fuel tank out-
doors and use a funnel or spout to prevent
spilling. Make sure to wipe up any spilled
fuel before starting the engine. Store gaso-
line in a clean, approved container, and
keep the cap in place on the container.
Keep gasoline in a cool, well ventilated
place; never in the house. Never buy more
than a 30 day supply of gasoline to ensure
volatility. Gasoline is intended to be used as
afuel for internal combustion engines;
therefore, do not use gasoline for any other
purpose. Since many children like the smell
of gasoline, keep it out of their reach be-
cause the fumes are dangerous to inhale,
as well as being explosive.
TO STOP ENGINE
•To stop the engine, turn the key to OFF
and remove key. Keep key in asafe
place. The engine will not start without th
key. See figure on next page.
TO.START ENGINE (ELECTRIC
START)
The snow thrower engine is equipped with
120 volt AC electric starter and recoil starte
Before starting the engine, be certain that
you have read the following information:
COLD START
•Insert the key and turn ON.
•Move the choke control to the FULL
position.
•Connect the power cord to the switch box
on the snow thrower.
Plug the other end of the power cord into
a three hole, grounded 120 volt AC
receptacle.
Push the primer button while covering the
vent holes as follows: (Remove finger
from primer button between primes).
Do not prime if temperature is above
50oF.
Two times if temperature is 50 ° F to 15°F
Four times if temperature is below 15°F.
Push down on the starter button until the
engine starts. Do not crank for more than
20 seconds at a time. This electric starter
is not thermally protected. Allow starter to
cool off for 10 minutes before starting
again or electric starter damaged can
Occur.
• Disconnect the power cord from the
receptacle first and.then from the switch
box on the snow thrower.
• When the engine starts,releasethe
starter buttonand move choke lever to
=1/2 choke" position. When engine runs
smoothly, move choke lever to "No
Choke" Position.
NOTE: Allow the engine to warm up for
several minutes before blowing snow in
temperatures below 0°F.
WARM START
• Be sure the choke is in the OFF posi-
tion and pull the starter handle until the
engine starts.
•Do not prime a warm engine. If the en-
gine fails to start, follow the Cold En-
gine Start instructions on page 8.
RecoilStarter
Vent Hole Handle
Starter
O O
Choke!Electric
Z_ CAUTION: This starter is equipped to
operate on 120 volt AC household current.
Follow all instructions carefully as set forth
in the "To Start Engine" section. When
connecting 120 volt AC power cord, always
connect the cord to the switch box on the
engine first, then plug the other end into the
household receptacle. When disconnecting
the 120 volt AC power cord, always unplug
from the household receptacle first.
TO STOP ENGINE
•To stop the engine, turn the key to OFF
and remove key. Keep key in a safe
place. The engine will not start without
the key. See figure above.
TO START ENGINE (RECOIL START)
Before starting th_ engine, be certain that
you have read and understood all the
instructions on the preceding pages.
COLD START
• Insert the key and turn ON.
•Move the choke control to the FULL
position.
• Push the primer button while covering the
vent holes as follows: (Remove finger
from pdmer button between pdmas).
Do not pdme if temperature is above
50OF.
Two times if temperature is 50 ° F to 15°F.
Four times if temperature is below 15°F.
•Pull the starter handle with a smooth
rapid movement. Do not allow the starter
rope to snap back. Rewind smoothly
while holding the starter handle. If the
engine fires but does not start, pull the
starter handle until the engine starts.
•After three pulls, repeat the priming and
pulling steps again.
•As engine starts warms up move choke
lever to =1/2 choke" position. When
engine runs smoothly, move choke lever
to =No Choke" Position
NOTE: Allow the engine to warm up for
several minutes before blowing snow in
temperatures below 0°F.
WARM START
•Do not prime a warm engine. If the en-
gine fails to start, follow the Cold En-
gine Start instructions on this page.
Z_ CAUTION: Never run engine indoors
or in enclosed, poody ventilated areas.
Engine exhaust contains carbon monoxide, •
an ododess and a deadly gas. Always stand
behind snow thrower(operator's position)
when starting engine. Do not put hands,
feet, hair or loose clothing in or near the
discharge chute deflector or auger housing
while the engine is running. The tempera-
ture of the muffler and neaby areas may
exceed 150 ° F.; avoid these areas also.
Z_ WARNING: Objects such as gravel,
rocks or other debris, if struck by the auger,
may be thrown with sufficient force to cause
personal injury or property damage.
We recommend standard safety glasses or
Wide Vision Safety Mask for over your
glasses.
,SNOW THROWINGTIPS
• Thissnowthrowerwillpropelitself
forwardwhenthehandleis raised
enoughto causetheauger blades to
contact the ground. The auger should
stop when auger control bar is released.
If it does not, refer to Adjust Auger
Control Cable paragraph on page 12.
•For most efficient snow throwing, turn the
discharge chute deflector to throw snow
downwind, and slightly overlap each
swath. In light snow take up to a full cut
and in heavy snow take less than a full
cut.
•The distance snow will be discharged can
be adjusted by moving the discharge
chute deflector. Raise the deflector for
more distance or lower the deflector for
less distance.
•In windy conditions, lower the chute
deflector to direct discharged snow close
to the ground where it is less likely to
blow into unwanted areas.
•Keep the area to be cleared free of
stones, toys and other foreign objects for
safety and to prevent damage to the
snow thrower.
•Do not use the auger propelUng feature
when clearing gravel or crushed rock
driveways. Move the handle down to
raise the auger slightly.
• The allowable forward speed of the snow
thrower is dependent on the depth and
weight of the snow. Expedence will
establish the most effective method of
using the snow thrower under different
conditions.
DRY AND AVERAGE SNOW
•Snow up to eight inch depth can be
removed rapidly and easily by walking at
a moderate rate. For snow or drifts of a
greater depth you may find it ,.lesirable to
slow your pace to allow the discharge
chute to dispose of the snow as rapidly
as the auger receives the snow.
•Plan to have the snow discharged in the
direction the wind is blowing,
WET PACKED SNOW
• Move slowly into snow of this condition.
The greater the depth, the slower you
should go. When it appears that the wet,
packed snow is causing the auger to slo_
down and the chute to clog, back off and
begin a series of short jabs into the snow
These short back and forth, 4 to 6 inch,
jabbing motions will =belch" the snow
from the chute.
SNOW BANKS AND DRIFTS
• In snow of greater depth than the unit,
use the jabbing technique descdbed
above. Turn the discharge chute away
from the snow bank. More time will be
required to remove snow of this type than
level snow,
PRODUCT SPECIFICATIONS
HORSE POWER: 3HP
DISPLACEMENT: 6.0 cu. in.
GASOLINE CAPACITY: 1 quart
(unleaded)
FUEL/OIL MIX RATIO: 40:1
(3.2 oz. of air-
cooled engine 2
cycle oil specified
for 40:1 per 1 gal. of
gas)
SPARK PLUG: Champion RCJ8Y
(Gap .030) or
Equivalent
lO
CUSTOMER RESPONSIBILITIES
SERVICE
RECORDS
Fill in dates as
lyou complete
, regular service
Before A_er
Each firet12
Usa Houm
TightenAll Screws& Nuts
Check Spark Plug
Check Drive Belts
LubricateChute ControlFlange
Check Fuel
Drain Fuel
GENERAL RECOMMENDATIONS
The warranty on this snow thrower does not
cover items that have been subjected to op-
erator abuse or negligence. To receive full
value from the warranty, the operator must
maintain the snow thrower as instructed in
this manual. The above chart is provided to
assist the operator in properly maintaining
the snow thrower.
SCHEDULE
As Before Begin
Needed =Storage Each
Seaaon
p,
v,,
v"
J
LUBRICATION CHART
SERVIC
DATES
SNOW THROWER
AFTER FIRST USE
•Check for any loose or damaged parts
after each use.
•Tighten any loose fasteners.
AFTER EACH USE
•Run the machine to clear the auger of
SNOW.
•Remove all snow and slush from the snow
thrower to prevent freezing of auger or
controls.
LUBRICATION -AS REQUIRED
•Lubricate the flange on the discharge
chute before s_orage. See To Remove
Top Cover instructions on page 12.
•See Lubrication Chart diagram for
lubrication points and type of lubricant.
Lubricatechuteo0ntr_flange,
CoatflangewithacUngingtype
grease such asLubrtptate.
ENGINE
SPARK PLUG
•Clean the spark plug and reset the gap
periodically. To service or replace spark
plug, see To Replace the Spark Plug
paragraph on page 15.
•Make sure that the spark plug is tightened
securely into the engine and the spark
plug wire is attached to the spark plug.
•If a torque wrench is available, torque
plug to 18 to 23 fo_t pounds.
•Clean the area around the spark plug
base before removal to prevent dirt from
entering the engine.
I(
CARBURETOR ADJUSTMENT
The carburetor on this snow thrower is not
adjustable.
IMPORTANT: If you think the carburetor is •
not operating properly, contact your
nearest Sears service center.
Z_ CAUTION: Never tamper with the •
engine govemor which is factory set for
proper engine speed. Over speeding the •
engine may increase the danger of •
personal injury and will void the engine
warranty. If you think the engine governor
high speed needs adjusting, contact your
nearest Sears service center who has the
proper equipment and experience to
make any unnecessary adjustments.
TO ADJUST THE CHUTE CRANK
ASSEMBLY
If you cannot rotate the chute crank fully to the
left and to the right, you need to adjust the
chute crank. See first figure on this page.
• Remove the top cover. See To Remove
Top Cover instructions on this page.
• Loosen both 1/2" nuts on the crank
adjusting bracket using 1/2" wrenches.
•Swivel the crank adjusting bracket to
allow about 1/8" clearance between the
notch in the flange and the outer diameter
of the worm.
=+ • Once this clearance is set, tighten the
nuts.
TO ADJUSTTHEAUGERCONTROL
CABLE
The auger control cable is set at the factory for
proper operation. If you need to adjust the
cable, because the control bar does not prep-
erly engage or disengage the auger, do the
following:
•Remove "Z" hook from the auger control
bar. See second figure on this page.
•Slide the boot toward the loose end of the
cable. See last figure on this page.
•Push the cable down through the hole in
the top of the cable adjustment bracket to
provide slack in the cable. See last figure
on this page.
• Remove the "Z" hook from the top hole in
12
the cableadjustment bracket and move to
the next hole away from the top of the
bracket. See last figure on this page.
Pull cable slack through cable adjustment
bracket and insert in the control bar. See
last figure on this page. _
Replace boot over cable adjustment
bracket.
Insed "Z" hook in the auger control bar.
Start the snow thrower and check that the
auger does not continue to turn when the
auger control bar is released.
Notch In
Range
Adjustments
,,=e
ment Bracket
Hook
Cable -_
Y
Zi C e,dust
meritBracket
Z"Hook
TO REMOVE TOP COVER
•Follow these steps from operator's
position.
•Remqve the T-knob and fasteners on the
discharge chute.
•Remove the gas cap. Boltsto be
•Remove the two bolts and nuts from the
front lip of the top cover. Use aflat head T_
screwdriver and a 3/8" wrench.
• Remove the bolt from the front right side.
Use a 5/16" and 3/8" wrench,
•Remove the four screws on the left side of
the top cover. Use a large flat head
screwdriver.
•Remove the bolt from the front left side.
Use a5/16" and 3/8" wrench. Chute
• Remove the four screws on the right side
of the top cover. Use a large flat head
screwdriver.
• Remove the three screws from the top
portion of the control panel. Use a large Fasteners
flat head screwdriver.
•Carefully pull up on the rear of top cover
making sure to clear gas tank.
•Carefully lift top cover over the three bolts
holding the lower chute to the chute ring.
NOTE: This area was designed to have a
tight fit, it will be necessary to rock top
cover carefully over these bolts.
• Remove top cover.
•Reinstall in reverse order.
TO REMOVE BELT COVER
•Follow these steps from operator's
position. See figure on this page.
•Using a large flathead screwdriver,
remove the heat shield from the rear of
the belt cover.
•Remove the four bolts and nuts holding
the belt cover to the auger housing. Use
a 5/16" and 3/8" wrench.
•Remove the two screws holding the belt
cover to the top cover. Use a large flat
head screwdriver. NOTE: If the top cover
is already removed, omit this step.
•Remove the one screw holding the belt
cover to the bottom cover. Use a large flat
head screwdriver.
•Grasp the bottom portion of the belt cover
and pull down and out to remove.
•Using a large flathead screwdriver,
remove the heat shield from the rear of
the belt cover.
•Reinstall in reverse order.
Screws to be
removedfromTop
Cover
robe
removed from removed
Belt Cover from Belt
TO ADJUST BRAKE PAD Cover
The brake pad is adjusted at the factory and
no periodic adjustment is necessary.
IMPORTANT: Adjustment should only be
made to the brake if the brake pad has
become loose or has been removed. To
adjust proceed as follows:
NOTE: See figure on next page for proper
location of brake pad.
•Tum engine off.
•Remove belt cover. See To Remove Belt
Cover paragraph on this page.
•Remove the top cover. See To Remove
Top Cover instructions on page 12.
NOTE: Make sure the belt is in proper
position. See To Replace the Drive Belt
paragraph on page 14.
•Tie the control bail to the upper handle
with a piece of string. NOTE: This will
engage the pulley and belt system.
•Using a7/16 wrench, 7/16 socket, and a
rachet loosen screw and nut on brake
pad. See first figure on page 14 for
location of screw and nut.
• Adjust brake pad up or down to have a
1/8" gap between the bottom of the brake
pad and the belt.
•Tighten screw and nut.
13
Screw and nutto
be loosened
Brake Pad
i _i. .
Idler Pulley
Pulley
.,i ¸, • : ',!,.
Roller
TO REPLACE THE DRIVE BELT
The drive belt on this unit is of special
construction and must be replaced with the
same type belt available at your nearest
SEARS Service Center.
•Remove the belt cover. See to Remove
the Belt Cover paragraph on page 13.
•Move belt guide away from belt. See next
figure. Belt may come out without
loosening belt guide. Carefully press idler
pulley down to release brake pressure on
belt,
--_._.--..\v-1 i.. ,-'ri_J_/.jlpt_
_"_ Engine Pulley---_Q ._
Idler PuIIey-_._,_.p_r'_ _._,_
rc_kee
•Remove belt from between brake pad
and roller.
•Remove old beY(.
• Replace with new belt by carefully
pressing down on the idler pulley and
placing the belt between the brake pad
and roller with belt ribs down.
• Release belt pulley.
•Attach new belt to the engine pulley and
auger pulley.
•Make sure the belt is seated properly.
•Move belt guide into position. The belt
guide should be 3/32' from beR when
is engaged as shown in next figure.
•Reinstall belt cover.
Idler Pulley Pulley
@
TO REPLACE THE AUGER
Remove the belt cover, see To Remove
Belt Cover paragraph on page 13 and t_
drive belt. See the Drive Belt Replace-
ment paragraph on page 14.
Remove the auger pulley, see figure
below from the auger shaft (threads are
left hand; tum clockwise to remove). PI_
a piece of wood (2x4) on the center
paddle area to secure auger to keep frer
turning.
Remove the bearing assembly from the
left frame of snow thrower by removing
the two nuts. See figure below.
_>._ Auger Housing
J
Fr/a/rre Bearing As_ ,mbly
Left
,3pacer,_
•Slide the auger assembly out of the
bearing assembly on the right side of thq
snow thrower.
•Tip the auger assembly enough to allow
to slide out of the auger housing.
•install the new auger assembly in revers
order of removal.
14
TO REPLACE THE SPARK PLUG
NOTICE: This spark ignition system meets
all requirements of the Canadian Interfer-
ence-Causing Equipment Regulations.
NOTICE: This engine complies with all cur-
rent Australian and New Zealand limitaions
regarding electromagnetic intederence.
The spark plug is housed in the engine
compartment under the top cover and
cannot be seen under normal conditions.
TO REMOVE BOTTOM COVER
•First, remove bottom coven To remove
bottom cover proceed as following:
•Stand the unit onto its front end.
•Using a flathead screwdriver, remove the
ten screws. See figure below.
Remove four screwson righthand side of unit
Remove these
screwsfrom top
Remove
screws from left
side BottomCOver
•Remove bottom cover.
•The spark plug and wire are now visible.
•Remove the spark plug wire.
•Clean the area around the plug base to
prevent dirt from entering the engine
when the plug is removed.
•Remove the spa_ plug. If it is cracked,
fouled or dirty,,it must be replaced. See
page 10 for the proper replacement plug.
•Set the gap between the electrodes of the
new spark plug at .030 inch. Next, install
the spark plug in the cylinder head.
Torque plug to 18 to 20 ft. lb. If you do not
use a torque wrench, tighten the plug
firmly (See figure below).
• Push the spark plug wire onto the spark
plug.
•Reinstall the bottom cover.
ENGINE SERVICE
Unless the operator is fully qualified to
make engine repairs or adjustments, we
recommend that such work should be done
by technicians trained to work on snow
thrower type engines, Take your snow
thrower to your nearest SEARS Service
Center for repair and adjustment.
ADJUST ENGINE SPEED
Your engine speed has been factory set. Do
not attempt to change engine speed or it may
result in personal injury. If you believe that
the engine is running too fast or too slow, take
your snow thrower to your nearest SEARS
Service Center for repair and adjustment.
Z_ WARNING: Never store your snow
thrower indoors or in an enclosed, poorly
ventilated area. If gasoline remains in the
tank, fumes may roach an open flame,
spark or pilot light from afurnace, water
heater, clothes dryer, cigarette, etc.
To prevent engine damage (if snow thrower
is not used for more than 30 days) follow
the steps below.
SNOW THROWER STORAGE
•Thoroughly clean the snow thrower.
•Lubricate all the lubrication points. See
the Maintenance section, page 11.
•Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible
moving parts for damage, breakage and
wear. Replace if necessary.
•Touch up atl rusted or chipped paint
surfaces; sand lightly before painting.
•Cover the bars metal parts of the blower
housing and auger with rust preventative,
such as a spray lubricant.
ENGINE STORAGE
Gasoline must be removed or treated to
prevent gum deposits from forming in the
tank, filter, hose, and carburetor during
storage. Also during storage, alcohol
blended gasoline that uses ethanol or
methanol (sometimes called gasohol)
attracts water. It acts on the gasoline to
'" form acids which damage the engine.
•Remove bottom cover. See first step in
To Replace Spark Plug paragraph on
page 15.
•To remove gasoline, run the engine until
the tank is empty and the engine stops.
Then drain remaining gasoline from
carburetor by pressing upward on bowl
drain located on the bottom of carburetor.
See next figure.
• if you do not want to remove gasoline, a
fuel stabilizer (such as Craftsman fuel
stabilizer No. 33500) may be added to
any gasoline left in the tank to minimize
gum deposits and acids. If the tank is
almost empty, mix stabilizer with fresh
gasoline in aseparate container and add
some to the tank. Atways follow instruc-
tions on stabilizer container. Instructions
on stabilizer container. Then run engine a
least 10 minutes after stabilizer is added
to allow mixture to reach carburetor. Store
snow thrower in a safe place. See
Warning under STORAGE.
OTHER
•If possible, store your snow thrower
indoors with the gas removed and cover it
to give protection from duet and dirt.
• If the machine must be stored outdoors,
block up the snow thrower to be sure the
entire machine is off the ground.
• Cover the snow thrower with a suitable
protective cover that does not retain
moisture. Do not use plastic or vinyl.
NOTE: A yearly checkup or tune-up at a
SEARS Service Center is agood way of
ensuring that your snow thrower will provid_
maximum performance for the next season
Ca_urs_r
Drain Rightside view of
engme
16
TROUBLE CAUSE CORRECTION
_Difficult starting Defective sparkplug Replace defectiveplug
!Engine stalls Unitrunningon CHOKE
Blockedfuel line or lowon fuel
Water or dirt in fuelsystem
!Engine runs
erractically
or
Loss of power
Excessive
vibration
Units fails to
propel itself
Unit fails to
discharge snow
Loose parts; damaged impeller
Damaged auger
Drive belt loose or damaged
Incorrect adjustment of auger con- I
trol cable
Auger drive belt'loose Ordamaged
Auger control.cable not adjusted
correctly
Discharge chute clogged
Foreign object lodged in auger
Move choke lever to OFF positon
Clean fuel line; check fuel sup-
ply; add fresh gasoline (gaso-
line/oil mixture if 2-cycle engine)
Use carburetor bowl drain to
flush and refill with fresh fuel
Stop engine immediately and
remove key. Tighten all bolts
and make all necessary repairs.
If vibration continues, have the
unit serviced by a Sears service
repairman
Repair or replace auger assem-
bly
Replace drive belt
Adjustauger controlcable
Adjust auger drive belt; replace
if damaged
Adjust auger control cable
Stop engine immediatelyand re-
move key. Clean discharge
chuteand inside of auger hous-
ing
Stop engine immediately and re-
move key. Remove object from
auger.
17
CRAFTSMAN 21" -3H.P. SNOW THROWER 536.884582
ELECTRIC START ASSEMBLY
REF. ITEM
ENGINE
REF. ITEM
BOTFOM COVER
16
930
Note: Always use odglnel equipment
parts. Use of servise/replasement parts
otherthan odgtnalpartsmayvoidyour
warranty.
All unnumbered items are
Interchangeable with opposite
side
REP.i
NO. PART NO.
13 56022
14 305607
15 56026
16 302267
17 414106
18 271482
19 57444
930 56023
761124
PART NAME
Starter, Engine
Screw, 1/4-20x.88
Clamp, Strap-hinge
Screw, #6-32x2..50
Flatwasher.188x.38x.040
Nut, #6-32 Hexkeps
Cable Tie
Cord, Extension10 feet
Owner'sManual Eng/Sp
18
CRAFTSMAN 21" - 3H.P. SNOW THROWER 536.884582
ENGINE/DRIVE ASSEMBLY
REF.
NO. PART NO. PART NAME
10 ENGINE
11
12
20
21
22
23
24
25
26
27
28
30
31
32
33
40
18O077
120638
333970
180077
120638
579052
73826
313440
71071
120638
710312
313444
333594
71391
313472
32O077
Engine, Model 143.983071
(See Enginepages)
Screw, 5/16-18x.75
Washer, HvspUk
Brake Pad
•Screw, 5/16-18x.76
Washer, Hvsptlk
Screw, 1/4-20x.63
Nut, 1/4-20 Reghexctflk
Belt Guide
Ratwasher .349x.69x.066
Washer, HvspUk
Screw, 5/16-18xl .00
Idler PivotArm
Shoulder Bolt,5/16-18
Nut, 5/16-18 Reghexctdk
ExtensionSpring
IdlerArm
REF,
NO.
41
42
45
46
47
50
51
52
53
60
61
62
70
71
72
75
/q
O
PART NAMEPART NO.
333594
71391
48924
302637
59O
180034
!71067
313443
73826
313436
414106
121223
339863
25640
181595
319596
ShoulderBolt, 5/16-18
Nut, 5/4,6-18 Reghexctdk
Idler Pulley
Screw, 3/8-16xl.50
Nut, 3/8-16 Ctrlkjam
Screw, 1/4-20xl .50 In.
Fiatwasher, .281x.63x.0_
Roller,Belt Pinch
Nut, 1/4-20 Reghexctdk
Rod, ClutchLinkage
Flatwasher, .188x.38x.04
Cotter Pin .062x.75
Engine Pulley
Spring Washer
Screw, 5/16-24 x .75
Belt, PolyV
CRAFTSMAN21" - 3H.P.SNOWTHROWER536_884582
®
333966G
PART NO. PART NAME
REF. _
NO.
80
81
90
91
92
100
101
102
107
108i
109
110
112
113
114
115
116
117
118
333769-853
333767
333987
180044
782585
333749:853
180020
782585
302628
71067
73826
333739
340300
323363
47345
335351
323387
56679
335906
Frame, Side RH
Frame, Side LH
Channel, Frame Support
Screw, 1/4-20x2.00
Nut, 1/4-20 Reghexctrlk
Bracket, Fuel Tank 1.5 Qt
Screw, 1/4-20x.75
Nut, 1/4-20 Reghexctdk
Screw, 1/4-20x.75
Flatwasher.281x.63x.065
Nut, 1/4-20 Reghexctdk
Fuel Tank 1.5 Qt.
Fuel Cap 40:1
Gas Tubing 8 Inches
Hose Clamp
Plate, BoltingSupport
Hose Clamp
Filter, In-Line
Tubing, 6 inches
DISCHARGE CHUTE ASSEMBLY
REF.
NO.
580
581
582
583
590
591
592
i600
1601
602
603
604
605
606
607
608
PART NO,
333859
711752
577021
337166
334234
313686
302635
325847
308931
302843
71071
57171
71037
578088
71071
71391
PARTNAME
Ring, Chute
Screw, #10x.50 Tap
Guide, Chute
Seal Stdp
Lower Chute
Screw, 1/4-20 xo50
Nut, 1/4-20 Cntdk
Upper Chute
Wire, Hinge
Carriage Bolt 5/16-18xl .25
Flatwasher .349x.69x.066
Knob, T
Nut, 5/16-18 Reghex
Screw, 5/16-18x.75
Flatwasher .349x.69x.066
Nut, 5/16-18 Reghexctdk
337341A
@
CRAFTSMAN 21" - 3H.P. SNOW THROWER 536.884582
BELT COVER ASSEMBLY
@
@
®
REF.
NO.
!120
!121
1124
125
126
127
128
130
1131
1140
1141
142
143
:145
1146
147
150
PART NO.
340088
313685
578109
334298-853
313674
71067
782585
57587
333643
56992
313683
300193
49643
54601
335507
271172
340089
PART NAME
BottomCover
Screw, 1/4-14x.75 Slwatap
Nut, 1/4-20 Speed J Type
Panel, Control
Screw. 1/4-20xl.25
Flatwasher.281 lx.63x.065
Nut, 1/4-20 Reghexctdk
Grommet& Washer
Knob, Stand Tee
Switch, Ignition
Washer, Regintlk
Nut, 5/8-32, Ign. Switch
2 Keys & RingAssy
Pdmer, Enginer
Hose, Primer 9.50Lg
Nut, 1/4-20 Reghexkeps
Belt Cover
REF
NO. PARTNO.
151 12342
152 312300
157 313685
159 578109
160 335855-853
161 313685
162 578109
170 340087
171 12342
172 312300
173 313685
174 55380
176 578109
181 313685
182 578109
334311
PART NAME
Screw 10-24x.50 Wahhma
Nut, #10-24 Reghexctrlk
Screw 1/4-14x.75 Slwatap
Nut, 1/4-10 Speed J Type
Heat Shield
Screw, 1/4-14x.75 Slwatap
Nut, 1/4-10 Speed J Type
Cover, Top
Screw, 10-24x.5Wahhma
Nut, #10-24 Reghexctdk
Screw, 1/4-14x.75 Slwatap
Seal, StripAug Chute Foarr
Nut, 1/4-10 Speed J Type
Screw, 1/4-14x.75 Slwatap
Nut, 1/4-10 Speed J Type
21
CRAFTSMAN 21" - 3H.P. SNOW THROWER 536.884582
AUGER HOUSING ASSEMBLY
@
@
@
REF.
NO.
480
481
|82
t83
tg0
1.91
192
_,93
510
511
512
513
520
520-2
520-6
520-8
520-1C
529
530
531
532
533
534
540
541
PART NO.
340091
302628
71067
73826
55323
i577707
302628
302635
577023
710263
71067
302635
327072
302565
49838
335992
309376
580251
43846
334287
579052
71067
73826
578101
313670
PART NAME
Auger HousingAssy.
Screw, 1/4-20x.75
Flatwasher,.281x.63x.065
Nut, 1/4-20 Reghexctrlk
Scraper Blade
Rivet, Ovset
Screw 1/4-20x.75
Nut, 1/4-20 Cntrlk
Beadng, Range
Screw 1/4-20xl .00
Ratwasher .281x.63x.065
Nut, 1/4-20 Cntdk
AugerAssembly
Blade, Auger
Rivet, Ovset
Blade, Center
Auger & Blade Assy
Retainer, Beadng
Bearing,Ball
Beadng Retainer
Screw 1/4-20x.63
iRatwasher .281x.63x.065
Nut, 1/4-20 Reghexctdk
Spacer, Sleve.640x.88x.15
Pulley, Poly6" 333969C
22
CRAFTSMAN 21" -3H.P. SNOW THROWER 536.884582
WHEEL ASSEMBLY
REF,
NO. PART NO.
650 313678
_'__i iiii_,,..';:I'I!!='_'_'_, _" 660651661662760713583409577598583409
661
HANDLE ASSEMBLY
PART NAME
Axle, Shaft
Flatwasher.391x1.00x.125
Tire & Rim6xl .50
Flatwasher.391x1.00x.125
Ring, Retaining
334309B
760
764
765_.
F743
_740
741
REF.I
NO. PART NO.
740 313449
741 113441
742 113448
743 308146
744 313471
750 333909-853
751 313674
752 71067
PARTNAME
Cable, Upper Control
=Bracket, Cable Adjust
I Cable, Lower Control
!Boot,Clutch Spdng
Spflng, Extertslon
Lower Handle
Screw 1/4-20xl.25
Ratwasher .281x.63x.065
!REF.
INO. PART NO;
753 782585
760 333919-853
761 333954-853
762 337584
763 311936
764 57171
765 ;'1037
PART NAME
Nut, 1/4-20 Reghexctdk
Upper Handle
Control Bail
Bolt,5/16-18x2.00 CUH
Formed Washer
Knob, T 2Blade 5/16-18 Nut
!Nut, 5/16-18 Reghex
334312A
CRAFTSMAN 21" - 3H.P. SNOW THROWER 536.884582
DECALS
REF.
NO. PART NO.
821 340737
822 761152
824 712352
826 69880
828 318494
829 761078
830 70142
831 70141
835 761150
PART NAME
Decal, Electdc Start
Decal, Dash ES
Decal, Cr_tsman 3/21
Decal, Warn Hot Muffler
Decal, Choke
Decal, Dang Stdpe
Decal, Danger Chute Hand
Decal, Danger Auger
Decal, AugerControlBar
344251A
CHUTE CONTROL ROD ASSEMBLY
850
REF,
NO.
85O
851
852
853
854
855
856
857
858
PART NO
337941
71072
71082
313431
335264
71072
57082
331532
3809
PART NAME
Chute Rod Assembly
Flatwasher .406x.81x.066
Cotter Pin.094xl.00
Washer, CurvedSpring
Chute Crank BrktAssy
Ratwasher .406x.81x.066
Knob, Sleeve
Nut, Push
Cart. Bolt 1/4-20x.63
REF
NO.
859
860
861
870
871
872
873
874
P4
PARTNO.
120393
71060
71034
333946-853
340720
71071
71060
71037
PART NAME
Flatwasher.344x.69x.065
Washer, Sptlk
Nut, 1/4-20 Reghex
Chute Rotate Bracket
Cart, Bolt,5/16-18x.75
Flatwasher.344x.69x.066
Washer, Sptlk
Nut, 5/16-18 Reghex
334313C
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER 143.983071
101
69
/
\
77
I
361 _33A
395 z
6"_34 A
274 275
277
25
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER 143•98307"
REF.
1
PART# PARTNAME
16B 490291A
19 570707
24 530110
29 530150
29A 530104A
30 290680
33A 570644
34A 650579
41 310283A
42 310190
43 310167
45 310235B
e
48 650633
69 510292A
69A 510323A
75 510319
77 530105
89A 6_1,032
90 611066
92 650815
93 650390
100 34443A
101 610118
103 651007
119 510274A I
120 250240B
131 650477
135 611049
163 650838
169 510325A
CYLINDER (Order S/B if
replacementis needed)
AIR VANE
EXTENSION SPRING
BALLBEARING
NEEDLE BEARING &
LINER SET (37 NEEDLES)
CARTRIDGE BEARING
CRANKSHAFT
COVER PLATE
SCREW, 10-24X1/2" TORX
' T-25
PISTON & PIN ASSY (INCL
' 413_jGSET
PISTON PIN RETAINING
RING
CONNECTING ROD ASSY
(INCL 29,29A,&46)
CONNECTING ROD BOLT
CYLINDERCOVER GASKE1
COVER PLATE GASKET
OIL SEAL
CARTRIDGE BEARING
ADAPTER SLEEVE
FLYWHEEL
BELLEVILLEWASHER
FLYWHEEL NUT
SOLID STATE IGNITION
SPARK PLUG COVER
SCREW, TORX
T-15, 10-24 X 15/16•
CYLINDER HEAD GASKET
CYLINDER HEAD
SCREW, TORX T-30,
1/4-20X3/4"
RESISTOR SPRK PLUG
wRCJ6Y)
ASHER
COMPRESSION RELEASE
COVER GASKET
REF. PART# PART NAME
172A 570708
174 650579
177 650959
164 510326A
186 490322
187 570438A
216 570645
257 650911
258 350422
260 350437
261 !650737
274 510207
275 390330
277 650869
285
287
325
330
350
351
361
370
380
390
395
400
590551A
650926
29443
61!164A
570629A
32180C
650909
36261
640090
590743
88941
510324B
COMPRESSION RELEASE
COVER
SCREW, TORX T-25
10-24X1/2•
SCREW 5/32 ALLEN,
1/4-20X1•
CARBURETOR GASKET
GOVERNOR LINK
SPACER
R.P.M. ADJUSTING LEVER
SCREW, TORX T-30
1/4-20X5/8•
BLOWER HSING BASE
_NCL 75)
LOWER HOUSING
SCREW 114-20Xll2"
EXHAUST GASKET
MUFFLER
SCREW,
1/4-20X2-3/4'
STARTER CUP
SCREW, 8-32 X 21/64=
WIRE CLIP
WIRE HARNESS
PRIMER ASSEMBLY
PRIMER LINE
SCREW, TORX
T-30,1/4-20 X 7/8"
LUBRICATION DECAL
CARBURETOR(INCL. 184)
REWIND STARTER
ELECTRIC STARTER
MOTOR (120 VOLT) (OPT)
GASKET SET
26
CARBURETOR NO. 640090
4,.O
0_37
REF. PART#
1 632166A
i2 632169
4 631184
5 631183
6 631621
7 650506
10 631300
14 631815
15 630735
16 632164
25 631949
26 632386
27 631024
26 632019
29 631028
30 631021
31 631022
32 27136A
33 27554
36 640080
37 632547
40 640087
44 2711O
48 631027
PART NAME
THRO'I_LE SHAFT & LEVER ASSY
THROTTLE RETURN SPRING
DUST SEAL WASHER
DUST SEAl.;(THROTTLE)
THROTTLE SHUTTER
THROTTLE & CHOKE SHUTTER SCREW
CHOKE SHAFT & LEVER ASSY
CHOKE SHUTTER
CHOKE POSITIONING SPRING
FUEL FITTING
FLOAT BOWL ASSY (INCL. NOS. 32 & 33)
FLOAT DAMPENING SPRING
SHAFT, FLOAT
FLOAT
"O" RING, FLOAT BOWL TO BODY
INLET NEEDLE, SEAT & CLIP(INCL. NO 31)
SPRING CLIP
BOWL DRAIN ASSY
DRAIN PLUNGER GASKET
MAIN NOZZLE TUBE
"O" RING, MAIN NOZZLE TUBE
HIGH SPEED BOWL NUT
BOWL NUT WASHER
WELCH PLUG, ATMOSPHERIC VENT
27
CRAFTSMAN 120 VOLT ELECTRIC STARTER KIT NO. 143.88941
REF. PART NAME
1
2
3
4
7
PART#
650819
650742
650909
32450B
SCREW, HEX HD 6-32X2
FLATWASHER 5/32" (STANDARD PART)
NUT & LOCKWASHER 6-32
SCREW, INTERNAL TORX,
HEX WASHER HD 1/4-20X7/8
CORD, EXTENSION (10' 6" LONG)
CLAMP, HOSE (STANDARD PART;
ORDER LOCALLY)
TIE WRAP (11" LONG)
(STANDARD PART; ORDER LOCALLY)
29
For the repair or replacement parts you
need delivered directly to your home
Call 7 am-7 pm, 7 days a week
1-800-366-PART
(1-800-366-7278)
Para ordenar piezas con entrega
a domicilio -1-800-659-7084
For in-house major brand repair service
Call 24 hours a day, 7 days a week
1-800-4-REPAIR
(1-800-473-7247)
Par.a pedir servicio de reparaci6n a
domicilio - 1-800-676-5811
For the location of a Sears Parts and
Repair C_nter in your area
Call 24 hours a day, 7 days a week
1-800-488-1222 IlimiI
mmmmmm
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am -5pm, Monday-Saturday
1-800-827-6655
When requesting service or ordering
parts, always provide the following
information:
• . Product Type •Part Number
•Model Number •Part Description
8E/AR8
America'sRepairSpecialists
Printed in U,S.A.

Navigation menu