Craftsman 646107391 User Manual BUFFER/POLISHER SYSTEM Manuals And Guides L0020230

CRAFTSMAN Buffer/polisher Manual L0020230 CRAFTSMAN Buffer/polisher Owner's Manual, CRAFTSMAN Buffer/polisher installation guides

User Manual: Craftsman 646107391 646107391 CRAFTSMAN BUFFER/POLISHER SYSTEM - Manuals and Guides View the owners manual for your CRAFTSMAN BUFFER/POLISHER SYSTEM #646107391. Home:Tool Parts:Craftsman Parts:Craftsman BUFFER/POLISHER SYSTEM Manual

Open the PDF directly: View PDF .
Page Count: 7

Owner's Manual

Double Insulated

BUFFER/POLISHER SYSTEM

Model No. 646.107391

®

CAUTION:

Read and follow all safety

rules and operating

instructions before first

use of this product.

• Safety Rules

• Operation

• Maintenance

• Accessories

• Espa5ol

Save this manual for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit our Craftsman website: www.sears.com/craftsman

,_ WARNING: Read and

understand all instructions.

Failure to follow all instructions listed

below may result in electric shock, fire

and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

WORK AREA

• Keep your work area clean and well lit. •

Cluttered benches and dark areas invite

accidents.

• De not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the •

dust or fumes.

• Keep bystanders, children, and visitors

away while operating a power tool.

Distractions can cause you to lose

control.

ELECTRICAL SAFETY

• Double insulated tools are equipped with

a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized

extension cord only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a

qualified electrician to install a polarized

outlet. Do not change the plug in any way

to make it fit your extension cord. Double

insulation [] eliminates the need for the

three-wire grounded power cord and

grounded power supply system.

• Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your

body is grounded.

• Don't expose power tools to rain or wet

conditions. Water entering a power too!

will increase the risk of electric shock.

• Do not abuse the extension cord. Never,

use the cord to carry the tools or pull the

plug from an outlet. Keep cord away

from heat, oil, sharp edges or moving

parts. Replace damaged cords

immediately. Damaged cords increase

the risk of electric shock.

• When operating a power tool outside, use

an outdoor extension cord marked "W-A"

or '_N:' These cords are rated for outdoor

use and reduce the risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication. Amoment of inattention

while operating power tools may result in

serious personal injury.

Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves

away from moving parts. Loose clothes,

jewelry, or long hair can be caught in

moving parts.

Avoid accidental starting. Be sure switch

is off before plugging in. Carrying tools

with your finger on the switch or

plugging in tools with the switch on

invites accidents.

Do not overreach. Keep proper footing

and balance at all times. Proper footing

and balance enables better control of

the tool in unexpected situations.

Use safety equipment. Always wear eye

protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection

must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical ways to

secure and support the workpiece to a

stable platform. Holding the work by

hand or against your body is unstable

and may lead to loss of control.

• Do not force tool. Use the correct tool for

your application. The correct tool will do

the job better and safer at the rate for

which it is designed.

• Do not use tool if switch does not turn it

on or off. A tool that cannot be controlled

with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing the

tool. Such preventive safety measures

reduce the risk of starting the tool

accidentally.

2

TOOL USE AND CARE

• Storeidle tools out of reachof children

and other untrainedpersons.Toolsare

dangerousin the handsof untrained

users.

• Maintain tools with care. Properly

maintained tools are less likely to bind

and are easier to control.

• Check for misalignment or binding of

moving parts, breakage of parts, and

any other condition that may affect the

tool's operation. If damaged, have the

tool serviced before using. Many

accidents are caused by poorly

maintained tools.

Use only accessories that are

recommended by the manufacturer for

your model. Accessories that may be

suitable for one tool may create a risk of

injury when used on another tool.

SERVICE

• Tool service must be performed only by

qualified repair personnel. Service or

maintenance performed by unqualified

personnel may result in a risk of injury.

• When servicing a tool, use only identical

replacement parts. Follow instructions in

the maintenance section of this manual.

Use of unauthorized parts or failure to

follow maintenance instructions may

create a risk of electric shock or injury.

Before you begin, make sure your car is

clean and dry. The work area should be

dry also. If necessary, remove road tar

with a general cleaner before polishing.

Also, remove excess grease spots, bug

stains, etc.

NOTE: The Wax & Polishing Solution

containers shown in the illustrations are

representative. Yours may look different.

A

Place the blue wax applicator bonnet on

pad as shown. Make sure the elastic is

tucked down securely and evenly around

the underside of the pad.

C FOR LIQUID WAX

Apply three or four swirls of Cleaner/Glaze

over the wax on the wax applicator

bonnet. DO NOT APPLY WAX DIRECTLY

TO CAR. This first application should do

about 1/4 of the car. For the second and

third applications of wax, use half the

quantity stated above. The bonnet will not

absorb as much when reloading.

B FOR PASTE WAX

Spread about a heaping teaspoonful of wax

evenly over the entire surface of the wax

applicator bonnet. Use a putty knife or any

flat object. DO NOT APPLY WAX DIRECTLY

TO CAR. _

D

Tool is equipped with cord lock feature to

prevent the extension cord from detaching

during use. Plug cord into unit, then feed

the cord as shown.

3

E

ALWAYS START AND STOP THE

POLISHER ON OR AGAINST THE

SURFACE.

G

After flat surfaces are covered with wax,

do sides of the car. Hold the polisher as

shown. Let the cord hang free. It is not

necessary to use a criss-cross motion on

doors and fenders.

F

Before beginning, locate the LOCK button

on the trigger switch. To lock the polisher

in ON position for ease of operation, press

the LOCK button. To release, press the

trigger switch.

Place the extension cord over your

shoulder and do flat surfaces first--hood,

trunk and roof. Cover areas quickly with

broad, sweeping strokes in a ¢riss-cross

pattern.

DO NOT press down on the polisher.

The machine's action, not pressure,

does the best job.

t

LErr =:>'_m<_,T

°° o.=}.1°_

Lq

_,',JI

,,=,_ I

4

H

Remove the wax applicator bonnet and

use it to hand-polish all hard-to-reach

surfaces; under the bumpers, around the

door handles, etc.

Throw away the wax applicator bonnet

and put a clean terrycloth bonnet on the

polisher.

J

Polish the wax in the same order it was

applied. Use long, sweeping strokes in a

criss-cross pattern. Do not press hard. Let

the polisher do the work.

4

• Terrycloth bonnets are 100% cotton and

can be machine-washed in cold water

with a small amount of detergent, then

machine-dried at low heat. However,

hand-washing and air drying is recom-

mended for longer terrycloth bonnet life.

• Wax applicator bonnets are to be used

only once, then thrown away.

•To prolong pad life and shape, always

store polisher with pad face up.

•Remove bonnet from pad when polisher

is not in use so that pad can dry out and

retain its original shape.

• Badly oxidized paint may require several

applications. DO NOT USE ABRASIVE

COMPOUNDS.

• The most common error is applying too

much wax. If pad becomes saturated, it

will not last as long, end polishing will

be more difficult and take longer.

• If applicator bonnet continually comes off

pad, you may be using too much wax.

• If buffing seems difficult, you may have

used too much wax.

•Use only mild soap and a damp sponge

to clean polisher. Do not immerse any

part in liquid. If polisher needs repair,

use only identical replacement parts

illustrated and listed on Page 6.

• The lamb's wool bonnet is only to be

used for the final buff. Do not use it to

apply or remove wax.

• Lamb's wool bonnets can be cleaned by

hand washing in lukewarm water and

mild detergent; then machine dry at the

lowest setting.

TO REPLACE PAD ASSEMBLY

1. Insert screwdriver through aperture

between polisher and pad, and brace

against counterweight.

2. Remove center bolt with 1/2" deep well

socket wrench, turning clockwise.

5/16 ° Lett-thfeaded Bolt

/(V2"H,aa)

TO %. _Counterwe*ght

LOOSen

3. Replace pad assembly and turn bolt

counterclockwise.

CARTON CONTENTS

• Buffer/Polisher (1) 120VAC, .50 amps

• Wax Applicator Bonnet (1)

•Terrycloth Bonnet (1)

AVAILABLE ACCESSORIES

Item

100% Lamb's Wool Bonnet (1)

Terrycloth Bonnets (2)

Wax Applicator Bonnets (4)

Cleaner/Glaze (8 oz.)

Clear ProTM Wax (8 oz.)

iwax(8oz.)

Stock#

25298

10607

10610

10996

10995

:10998

FULL ONE YEAR WARRANTY

If this product fails due to a defect in

material or workmanship within one year

from the date of purchase, Sears will at its

option repair or replace it free of charge.

Return this product to a Sears Service

Center for repair, or to place of purchase

for replacement, Note: Bonnets and

foam sponge rubber pad are expendable

items and are not covered by this

warranty.

If this product is used for commercial

purposes, this warranty applies for only

90 days from the date of purchase.

This warranty gives you specific legal

rights, and you may also have other

rights which vary from state to state.

Sears Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179

5

KEY PART

NO. NO.

1 41P26039

2 41P26250

3 41P18020

3A 41P18605

3B 41P14019

3C 41P18606

3D 41P14018

4 41P2503902

5 41P18501

5A 41P18107

6 41P21500

7 41P23204

8 41P17005

9 41P27019

10 41P18024

41P58056

DESCRIPTION QTY.

Housing Right 1

Housing Left 1

Screw 3/4" 9

Small Spring, Lock Button 1

Lock Button 1

Large Spring, Switch Actuator 1

Switch Actuator 1

Wire Harness Sub Assembly 1

Bearing 1

Flat Washer 1

Armature Assembly 1

Magnet, Yoke Assembly 1

Counterweight 1

Pad/Pad Holder Assembly

(pre-assembled) 1

Left-Handed

Threaded Bolt 1

Owner's Manual 1

R

For in-home major brand repair service:

Call 24 hours aday, 7days a week

1-800-4-MY-HOME =' (1-800-469-4663)

Para pedir servicio de reparaci6n adomicilio - 1-800-676-5811

For the repair or replacement parts you need:

Call 6 a.m. -11 p.m. CST, 7 days a week

PartsDirect '_

1-800-366-PART (1-800-366-7278)

www.sears.com/partsdirect

Para ordenar piezas con entrega adomicilio - 1-800-659-7084

For the location of a Sears Service Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

To purchase or inquire about a Sears Maintenance Agreement:

Call 7 am - 5 pm CST, Monday - Saturday

1-800-827-6655

SEARS

HomeCentral 'M

J

58-056F © 1999, All Rights Reserved Printed in Mexico