Craftsman 706650110 User Manual TOOL CHEST Manuals And Guides L0908372

CRAFTSMAN Tool Chest Manual L0908372 CRAFTSMAN Tool Chest Owner's Manual, CRAFTSMAN Tool Chest installation guides

User Manual: Craftsman 706650110 706650110 CRAFTSMAN TOOL CHEST - Manuals and Guides View the owners manual for your CRAFTSMAN TOOL CHEST #706650110. Home:Tool Parts:Craftsman Parts:Craftsman TOOL CHEST Manual

Open the PDF directly: View PDF .
Page Count: 11

Download
Open PDF In Browser	View PDF

ASSEMBLY
INSTRUCTIONS

Chest Model No.
Black 706,651130
Red 706.651150

Intermediate
Model
Black 706,652640
Red 706.652650

No.

;

I:'RII MIIN
i

Rollaway Model No.
Black 706.650110
Red 706.650120

CHEST
AND
ROLLA WAY
Sold by SEARS,

ROEBUCK

AND

CO,, Chicago,

IL 60684

U.S,A.
Printed
F692A1

in U.S.A.

Aug.!7, 2009 11:09AM

Waterloo

No,1181

Grand

III

TOOLS

REQUIRED

1/4

3/8

C_AF'iYS_A_
7/1 6

9/1 6

Q
BEFORE YOU ASSEMBLE

THE

CHEST

AND

ROLLAWAY:

Sort out and account for all parts to make sure that you have all necessary materials
to
assemble the chest and rollaway.
Do not discard packing materials
until all parts are
accounted
for.
NOTE:
Each unit contains a bag of hardware,
Listed below are the totals for all three units
followed

by the

number

KEY
A
B
C

QTY
48
4
16

PART NO.
M8738
MI0665
M8716

M6603

required

per unit;

DESCRIPTION
SCREW
SCREW

10-24
14-10

SCREW
SCREW

5/16-18
x 3/4"
:3/8-16 x 3/4"

14-10

x 5/16"
x 5/8"

24 each:Chest&
Rollaway onl_ =

Rollaway only
4 each Chest & intermediate

5/8

10-24

@
3/8-16

Rollaway-

5/16

@
x 3/4

5/16-,18

x 3/4

1
i

Aug17, 2009 11'10AM
i

I.r

WARNING:
!
DO NOT ALTER

No,1181

W&ter!00 Gr_nd

P. 3

THE PRODUCT

THE

FOLLOWING

MANNER:

1) WELDING
LOCK BARS OR DOLLIES ONTO THE UNIT.
2) MOUNTING
CHEST OR ROLLAWAY
ONTO ANY MOVING OBJECT SUCH AS TRUCK
BED, BOAT DECK, OR CAR TRAILER.
j!
WARNING:
J
STORAGE UNIT WILL TiP IF A NUMBER OF DRAWERS
ARE EXTENDED
WHICH
MAY
CAUSE PERSONAL INJURY OR DAMAGE.
IF

WARNING:
I
BEFORE MOVING
UNIT, BE SURE ALL DRAWERS
ARE FULLY CLOSED
FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE.

HELPFUL

AND

LOCKED.

HINTS:

1) Periodically

drawer

cleaned with
2) Chest may be
3/8-16
x 3/4"
.3/8-16
x 3/4"

front,

pulis

and other

rollaway

and chest

surfaces

should

a milcl detergent
end water to keep them looking new.
attached
to the rollaway
after the rollaway
is assembled
with the four
screws
(D). Remove the top two drawers
of the rollaway
and screw
screws
(D) into weldnuts
in chest and wrench
tighten.

3) For ease of operation,
lubricate
slide channels periodically
with petroJeum jelly,
4) If:it becomes necessary
to remove drawers for cleaning or due to damage follow these
slide removal
instructions.
COMPOUND
SLIDES:
A. Pull drawer all the way open then push back 1/16 of an inch.
B. Insert a screwdriver
into this slot in the slide and push in on the stop un'til it clears the
lance, Repeat the procedure
on the other slide and remove drawer.
C. To reinstall drawer,
pry stop far enough out to engage lance(3/1 6" to 1/4") and push
drawer onto slides until
BALL BEARING SLIDES:

stops

engage

lances.

A. Pull drawers
all the way open.
B. Remove screw and washer
from

both

C• Lift drawer

in slide clear slots

D. To reinstall,

up and out
reverse

until

tabs

sides

of drawer.
in drawer.

procedure,

COMPOUND

SLIDE

STO
_

I DE
SCREWDR
LUBRI

I_
CATE zj'_

2
m

I1 lOAM

Waterloo

706.651130
706.651150

No.1t81

Gra.nd

BLACK
RED

P. 4

WHEN ORDERING REPLACEMENT
PARTS ALWAYS
GIVE THE FOLLOWING INFORMATION:
MODEL NUMBER
MODEL DESCRIPTION
PART NUMBER
PART DESCRIPTION
QUANTITY
PART COLOR

5
6
8
9

I KEY
1
2
3
4
5
6
7
8
9
10
11
12

PART NO.
M9316
IM9317A1
T15410
T15409
M10526
T14009A2
M9091A1
A12451
M7413A8
M9400-PA
M7413A11
M8640

NOTE: 1.

DESCRIPTION
BALL STUD
GAS SPRING
LOCK BAR COVER
LOCK ROD COVER
NAMEPLATE
INSIDE SLIDE
ROLLER SLIDE RIGHT
DRAWER
DRAWER LINER
DRAWER TRIM
DRAWER LINER
DRAWER DIVIDER

KEY
13
14
15
16
17
18
19
2O
2!
22
23

PART NO.
M10520
M9361A2
IT16874
A12450A1
T15397
M9400A1-PA
A12449
M9090A1
A12450
M10100A1
M1915
F692

DESCRIPTION
DRAWER STOP
ACTUATOR
ROD
LOCK BAR
DRAWER
LOCK BAR
DRAWER TRIM
LOCK ROD ASSEMBLY
ROLLER SLIDE LEFT
DRAWER
LOCK
HANDLE
INSTRUCTION

SHEET

ALL UNNUMBERED PARTS ARE INTERCHANGEABLE WITH OPPOSITE SIDE.

5-92
! 22200

MODEL N0.70ro._;2640
706.652650

BLACK
RED

WHEN ORDERINGREPl.ACLM_N!_ P/_TS ALWAYS
GIVC TI IE FOLLOWING INFORMATION:
MODEL NUMBER
MODEL DESCRIPTION
PART NUMBER
PART DESCRIPTION
QUANTITY
PART COLOR

II
lO

KEY
1
2
3
4
5
6
7

DESCRIPTION
PART.NO., " " •
M10526
.....
NAMEPLATE
A12450.
A12450A1
Mg091AI
M7413A11
A 12450A3
M9400A1-PA

KEY
.
8
9
10

DRAWER
DRAWER
ROLLER SLIDE RIGHT
DRAWER LINER
DRAWER
DRAWER TRIM

PART NO.
M 10526
M9090A1
M10100A1
_410679
T16790
F692

DESCRIPTION

u_AWm
STOF'
_-.. _.

ROI.I_I_R ._UDI:

LOCK

LOCK PLATE
LOCK CAM
INSTRUCTION

=--

NOTI_;

ALL UNNUMDERED

PART$ ARE INTERCHANGE, ABLE _TH

L_k"T

I
O[-'PU_FFE SIDE,

SHEET

2009 11 11AM

No 1181

Waterloo Grand

N0.706.650110
706.650120

P 6

WHEN ORDERING REPLACEMENT PARTS ALWAYS
GIVE THE FOLLOWING INFORMATION:
MODEL NUMBER
MODEL, DESCRIPTION
PART NUMBER
PART DESCRIPTION
QUANTITY
PART COLOR

BLACK
RED

17
II
k .

15.--

KEY I
--,
2
3
5
6
7
8
9
10
11

PART NO.

IM4763A 8
iM10578
:M6185
IM10526
i A12450A1
M9091A1
M8640
A12.450
MgO93A1
M7413A11
A12450A2

NOTE: 1.

DESCRIPTION

=.m

TOP MAT
HANDLE
END PLUG
NAMEPLATE
DRAWER
ROLLER SLIDE RIGHT
DRAWER DIVIDER
DRAWER
ROLLER SLIDE RIGHT
)RAWER LINER
)RAWER

KEY
12
13
14
15
16
17
18
19
20
21
u

PART NO.
M 10520
M9400A 1=PA
M10577
M10576
M 9092A 1
A12450A3
M9090A1
M 10679
M 10100A1
T16790
F692

'
DESCRIPTION
DRAWER STOP
DRAWER TRIM
SWIVEL CASTER w/BRAKE
FIXED CASTER
ROLLER SLIDE LEFT
DRAWER
ROLLER SLIDE LEFT
LOCK PLATE
LOCK
LOCK CAM
INSTRUCTION SHEET

ALL UNNUMBERED PARTS ARE INTERCHANGEABLE WITH OPPOSITE SIDE.

Aug,17. 2009 11'11AM
i

Wa.ter]ooGrand
ii

No.1181
II

P. ?

FIG.

CASTER,INSTALLATION:
(Rollaway
only)(Fig. 1)
Note: Swivel casters with brake (14) should be mounted on the same.sideof
the rollaway
as the side handle (2), Fixed casters (15) are mounted opposite. Caster axles should
be lubricated periodically for continued good performance.
1) Lay cabinet down on its back side.
2) Position caster on caster channel and line up holes.
3) Insert four 5/16-18
x 3/4 screws (C) througll holes in caster;
weldnuts in bottom of rollaway. Finger tighten.
4) Repeat steps 2 and 3 to attach remaining
5) Wrench tighten all screws.
6) Turn cabinet to an upright position.

caster channel

and into

casters.

211
.....
3
/

FIG,, 2

SIDE HANDLE INSTRUCTIONS:(Rollaway
only)(Fig. 2)
Note: Holes in the handle are tapped therefore nuts are not necessary for installation.
1) Align handle (2) with holes on side of rollaway.
2) Using 14-10 × 5/8 screws (B) in each hole, tighten with a screwdriver.
3) Insert plug (3) in each end of handle and press tight,

Aug.17. 2009 11'12AM

W&terloo

Gr&nd

No. 1181

DRAWER

LINERS,

P, 8

DIVIDERS,

AND TOP MAT

INSTALLATION:

Note: Before installing
dividers in drawers decide in which position and in which drawers
they would best serve your needs, Drawer liners and top mat may be cleaned with
soap and water to keep them looking new. Top mat and chest panel gaskets may also
be treated with a rubber conditioner to keep them soft and pliable.
1) Center dividers over the holes of the drawers in the desired locations.
2) Start 10-24 x 5/16 screws (A) through
divider. Tighten with a screwdriver.

bottom

side of drawer

and into

3) Remove foam drawer liners from bag and place them in the appropriate
Drawer liner may be cut with a scissors to fit around drawer dividers.
4) Place precut top mat on cabinet top for protection.

DRAWERS

28°t9

•

each
drawers.

LINERS.

x 16.00

28_19

16.00

Aug.17. 2009 11'12AM

W&terl00 Grand

N0,1181

LOCK SYSTEM

CHEST

._oooqo
1 _

P. 9

& ROLLAWAY

Your push button lock is presently set with a combination
of: First push #2 and #4
together,
and then #3. Make a habit of turning the knob [eft (counter-clockwise)
before
pushing the combination.
Should anyone have attempted
an improper combination,
this
action clears off such an attempt and reactivates the buttons.
TO OPEN;
1) Turn knob TO RESET (counter-clockwise)
to activate all buttons.
2) Push proper buttons in present order for the combination.
3) Turn knob RIGHT (clockwise)
to open.
TO LOCK:
1) Turn knob full LEFT (counter-clockwise)
TO CHANGE YOUR COMBINATION:

until it stops.

Note:You
may easily change to a new combination,
using one, all five or any number of
buttons you wish
in any order. Two or more buttons may be pushed at one time as part
of your new combination.
Simple
two and three button combinations
are easy to
remember
and still provide top security. Note: A particular
button can be pushed only
once in establishing a new combination.
.....
1) Open the storage unit and relock your push button lock.
2) Press the correct buttons in the proper order for your EXISTING combination.
3) On the back side of the lock is the "clear out" button, (atthe opposite end of the turn
knob) with your finger,
pencil
as it will go. (See Fig. 1A)

tip,

etc.,

push the "clear

out"

button

into

the lock as far

4) Turn the knob full LEFT (counter-clockwise)
to "clear out" the existing combination.
5) Press the buttons firmly and deliberately
in the desired sequence for your new
combination.
6) Turn the knob to the RIGHT (clockwise) to set your new combination
into the
mechanism.
Turn the knob ful! LEFT to lock. Your new combination
is now installed.

110 0 0 0 0
310 0 0 0 0

_i0 0 0 0 0
,,0 0 0 0 0
8

--.

•

2009 11:!2AM

Waterloo Gr&nd

P. !0

No.1181

INSTRUCTIONS

FOR FINDING

UNKNOWN

COMBINATIONS

CHEST & ROL.LAWA_Y: Remove top drawer. Remove (2) 8-32 nuts from plate and remove
lock. Remove the back marked "Simplex" by gently lifting up on the staked joints at both
ends with a screwdriver
or sharp tool. The chamber now resembles
FIG. 1.

u©
0

.S.TEP 1 (See FIG. 1)
With tweezers,
or other tool, slide E-ring
off unlocking
stud. With same tool, gently
lift the end of unlocking
slide over unlocking slide stud. Note; The unlocking
slide is under spring tension
and will be
easy to lift if pushed to the left to ease
tension. Swing unlocking
slidesufficiently
to clear gears, no further
than shown in
FIG. 2.

PIG.

STEP 2
Depress the lockout slide. The gears are
now free to rotate. Turn each gear so that
the slots are aligned as in FIG. 3.
PiG,

STEP 3.
Return unlocking

slide over unlocking

slide

r!
' _

stud while making certain the five toes are
engaged in the five pockets. It may be
necessary to adjust each gear slightly to
make proper alignment
between toes and gear
slots. (See FIG. 4)

STEP.4
Replace E=ring on stud. Your lock will now
resemble FIG. 4 and is ready for assembly
with back cover.
Reinstallation:
Replace back cover marked

"Simplex'.

Make

sure

staked joints
lock chamber

on both end plates fit through both slots on the back cover. Replace
in the door lock, switch lock, or other device. DO NOT ATTEMPT

RESET

COMBINATION

REASSEMBLED.
1. Turn

control

knob

Perform

UNTIL
the following

LEFT to stop

2. Depress buttons
for new
3. Turn control knob RIGHT
locked in.

THE
steps

position

COMPLETE
in the

and then

combination.
to stop position

and then

order

UNIT

HAS

the

TO
BEEN

shown:

release.
release.

Your

new combination

III

•

INSTRUCTIONS
(MISPLACED

FOR OPENING

OR FORGOTTEN

LOCKED

UNIT

COMBINATIONS)

Mark center

of machine

sc'rews with center

punch and drill out screws

until screw
brakes
loose.
Do not_ drill through
into unit,
instructions.
Order M10679
replacement
plate. While waiting
with #8-32 x 1/2" screws & nuts.

with

1/4"

drill bit

Recombinate
per previous
for new plate, reinstall lock

I
I

WARNING
IF A CHEST IS PLACED ON TOP OF THE
TOOL CABINET,
THE WORK SURFACE MUST
BE REMOVED.
FAILURE TO DO SO MAY
ALLOW THE CHEST TO SLIDE OFF THE CART
CAUSING
DAMAGE
AND POSSIBLE
PERSONAL
INJURY.

;

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 11
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Mon Sep 07 04:15:54 2009
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 706650110 User Manual TOOL CHEST Manuals And Guides L0908372

CRAFTSMAN Tool Chest Manual L0908372 CRAFTSMAN Tool Chest Owner's Manual, CRAFTSMAN Tool Chest installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation