Craftsman 917293650 User Manual Rear Tine, Gas Tiller Manuals And Guides L0804441

CRAFTSMAN Rear Tine, Gas Tiller Manual L0804441 CRAFTSMAN Rear Tine, Gas Tiller Owner's Manual, CRAFTSMAN Rear Tine, Gas Tiller installation guides

User Manual: Craftsman 917293650 917293650 CRAFTSMAN Rear Tine, Gas Tiller - Manuals and Guides View the owners manual for your CRAFTSMAN Rear Tine, Gas Tiller #917293650. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman Rear Tine, Gas Tiller Manual

Open the PDF directly: View PDF .
Page Count: 32

Caution:

Read and follow

all Safety Rules

and instructions

Before Operating

This Equipment

6.0 HP

17 iNCH TINE WIDTH

TU TULLERWiTH

COUNTER F_OTATI TIN

®Assembly

-Operation

Customer Responsibilities

oService and Adjustments

,Repa_r Parts

i iii ,, i i i ................................. i ,1111,1,,111,,111111,,i,i

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

i, ii ,, iii

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Rotary Tillers

TRAINING

,Read the Owner's Manual carefulty_ Be thoroughly

familiar with the controls and the proper use of the

equipment. Know how to stop the unit and disengage

the controls quickly

•Never allow children to operate the equipment.. Never

allow adutts to operate the equipment without proper

instruction

•Keep the area of operation clear of all persons, particu-

larly small children, and pets.

PREPARATION

•Thoroughly inspect the area where the equipment is to

be used and remove all foreign objects°

• Disengage all clutches and shift into neutral before

starting the engine (motor).

• Do not operate the equipment without wearing ad-

equate outer garments.r Wear footwear that will im-

prove footing on slippery surfaces°

•Handle fuel with care; it is highly flammable

•Use an approved fuel container.

.Never add fuel to a running engine or hot engine

.Fill fuel tank outdoors with extreme care. Never fi!I fuel

tank indoors.

-Replace gasoline cap securely and ciean up spilled

fuel before restarting.

oUse extension cords and receptacles as specified by

the manufacturer for all units with electric drive motors

or electric starting motors.

•Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by manufacturer).

OPERATION

oDo not put hands or feet near or under rotating parts.

=Exercise extreme caution when operating on or cross-

ing gravel drives, walks, or roads, Stay alert for hidden

hazards or traffic, Do not carry passengers.

- After striking a foreign object, stop the engine (motor),

remove the wire from the spark plug, thoroughly in-

spect the tiller for any damage, and repair the damage

before restarting and operating the tiller

° Exercise caution to avoid slipping or falling

•If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the cause

Vibration is generally a warning of trouble

•Stop the engine (motor) when leaving the operating

position,

oTake all possible precautions when leaving the ma-

chine unattended. Disengage the tines, shift into

neutral, and stop the engine.

° Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire

away from the plug to prevent accidental starting,

Disconnect the cord on electric motors.

. Do not run the engine indoors; exhaust fumes are

dangerous,

.Never operate the tiller without proper guards, plates,

or other safety protective devices in place,

=Keep children and pets away

• Do not overload the machine capacity by attempting to

till too deep at too fast a rate.

• Never operate the maclqine at high speeds on slippery

surfaces. Look behind and use care when backing.

•Never allow bystanders near the unit

o Use only attachments and accessories approved by

the manufacturer of the tiller (such as wheel weights,

counterweights, cabs, and the like).

.Never operate the tiller without good visibility or light

•Be careful when tilling in hard ground. The tines may

catch in the ground and propel the tiller forward, If this

occurs, tet go of the handlebars and do not restrain the

machine

MAINTENANCE AND STORAGE

°Keep machine, attachments, and accessories in safe

working condition.

- Check shear pins, engine mounting bolts, and other

bolts at frequent intervals for proper tightness to be

sure the equipment is in safe working condition.

Never store the machine with fuel in the fuel tank inside

a building where ignition sources are present, such as

hot water and space heaters, clothes dryers, and the

like. Allow the engine to cool before storing in any

enclosure.

oAtways refer to the operator's guide instructions for

important details if the tiller is to be stored for an

extended period.

- IMPORTANT-

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS

OF ATTRACTING ATTENTION TO IMPORTANT OR

CRITICAL INFORMATION IN THIS MANUAL

IMPORTANT: USED TO ALERT YOU THAT THERE ISA

POSSIBILITY OF DAMAGING THIS EQUIPMENT.

NOTE: Gives essential information that witl aid you to

better understand, incorporate, or execute a particular set

of instructions,.

i, ,,Ul i,i,lu ,,UllllUr,_l ......

t,_ Look for this symbol to point out im-

I _ portant safety precautions. It means

I_ CAUTION!!! BECOMEALERT!!! YOUR

SAFETY IS INVOLVED

I, u , i ii ui, i,i1_1i,Ulllllll

,,,, ,,,,,,,,,,,,,,,,,,,,,,,

CAUTION: Always disconnect spark

plug wire and place wire where it can-

not contact spark plug in order to pre-

vent accidental starting when setting

up, transporting, adjusting or making

repairs.

i,UUlll ii, i ,,Ul,i,

WARNING ...........

The engine exhaust from this product con-

tains chemicals known to the State of .Califor-

nia to cause cancer, birth defects, or other

reproductive harm.

u, i ilur Ullll,, iii ...... i,, ii,u,,

CONGRATULATIONS on your purchase of a Sears Tiller,

It has been designed, engineered and manufactured to

give you the best possible dependability and performance.

Should you experience any problems you cannot easily

remedy, pfease contact your' nearest authorized Sears

Service Center/Department. They have competent, welF

trained technicians and the proper tools to service or repair

this unit.

PIease read and retain this manual The instructions will

enable you to assemble and maintain your tiller' propedy

Always observe the "SAFETY RULES",

MODEL

NUMBER 917.293650

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WILL BE

FOUND ON THE MODEL PLATE ATTACHED TO

THE TOP OF THE TRANSMISSION,

YOU SHOULD RECORD BOTHSERIALNUMBER

AND DATE OF PURCHASE AND KEEPIN A SAFE

PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

HORSEPOWER: 6,0 HP

DISPLACEMENT: 11.88 cu_ino(195cc)

GASOLINE CAPACITY: 4 Quarts

Unleaded Regular

i OIL (API-SF/SG) : SAE 30 (Above 32°F)

(CAPACITY: 20 oz.) SAE 5W-30 (Befow 32°F)

SPARK PLUG :

(GAP: 030") Champion

RN4C

MAINTENANCE AGREEMENT

A Sears Maintenance Agreement is available on this prod-

uct. Contact your nearest Sears store for details.

CUSTOMER RESPONSIBILITIES

° Read and observe the safety rules.

o Follow a regular schedule in maintaining, caring for and

using your tiller.

o Follow the instructions under the "Customer

Responsibilities" and "Storage" sections of this Owner's

Manual..

IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL COMBUSTION ENGINE AND SHOULD t_OT BE USED ON

OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-COVERED OR GRASS COVERED LAND UNLESS THE

ENGINE'S EXHAUST SYSTEM IS EQUIPPED WITH A SPARK ARRESTER MEETING APPLICABLE LOCAL OR STATE

LAWS (IF ANY)._ IF A SPARK ARRESTER IS USED, tT SHOULD BE MAINTAINED IN EFFECTIVE WORKING ORDER BY

THE OPERATOR

IN THE STATE OF CALIFORNIA THE ABOVE IS REQUIRED BY LAW (SECTION _4442 OF THE CALIFORNIA PUBLIC

RESOURCES CODE). OTHER STATES MAY HAVE SIMILARLAWS_ FEDERAL LAWS APPLY ON FEDERAL LANDS+

SEE YOUR SEARS AUTHORIZED SERVICE CENTER/DEPARTMENT FOR SPARK ARRESTER. REFER TO THE REPAIR

PARTS SECTION OF THIS MANUAL FOR PART NUMBER.

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN TILLER

For two years from date of purchase, when this Craftsman Ti_ler is maintained, lubricated, and tuned up according to

the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in

material or workmanship.

This W&rranty does not cover:

o Expendable items which become wom during normal use, such as tines, spark plugs, air cleaners and belt&

° Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to

maintain the equipment according to the instructions contained in the owneCs manual.

o If this Craftsman Tiller is used for commercial or rental purposes, this Warranty applies for only 30 days from the

date of purchase.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN TILLER TO THE NEAREST SEARS

SERVlCE CENTER/DEPARTMENT IN THE UNITED STATE& THIS WARRANTY APPLIES ONLY WHILE THIS

PRODUCT IS IN USE IN THE UNITED STATES.

This Warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.

SEARS, ROEBUCK AND CO. D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179

i, u nl ,,in,nl lun ,i

TABLE OF CONTENTS

'll'n"lllHirll' i i i 'u nllu Ull'UlU''' i' i

SAFETY RULES ............................................................ 2

CUSTOMER RESPONSIBILITIES ...................... 3,13-15

PRODUCT SPECIFICATIONS ...................................... 3

WARRANTY ................................................................... 3

ACCESSORIES ............................................................. 5

ASSEMBLY ................................................................ 6-8

OPERATION ................ ;...... ;..................................... 9-12

MAINTENANCE SCHEDULE ...................................... 13

SERVICE & ADJUSTMENTS ................................. 15-18

STORAGE ................................................................... 19

TROUBLESHOOTING ................................................. 20

REPAIR PARTS-TILLER ........................................ 21-27

REPAIR PARTS-ENGINE ...................................... 28-33

SERVICEIPARTS ORDERING ................ BACK COVER

UNDEX

Accessories ........................................... 5

Adjustments:

Carburetor .....................................18

Depth Stake .................................10

Handle Height ...............................15

Side Shields ..................................11

Throttle .........................................18

Tines ............................................ 17

V-Belt (Ground Drive) .............. 16

Air Cleaner ....................................... 14

Belt:Belt Guard .................................. 16

Repair Parts ............................. 22

V-Belt (Ground Drive) ............. 16

Cooling System ................................. 14

Controls:

Choke ...............................................9

Throttle .......................................... 9

Drive (Tines) ................................ 9

Cultivating ............................................12

Customer Responsibilities:

Air Cleaner .......................................14

Cooling System .............................14

Finish ..............................................15

Maintenance Schedule ............ 13

Muffler ............................................ 15

Oil Change .................................. 14

Spark Plug ................................. 15

Tines ................................................17

Transmission ...............................15

WBelt (Ground Drive) ............... 16

Depth Stake:

Adjustment ..............:......................t0

Repair Parts ...................................25

Engine:

Air Cleaner ................................. 14

Cooling System ........................ 14

FuelType ......................................11

Engine (conrd)

Lubrication ................................ 14

Oil Level .........................................11

Oil Type .....................................11,14

Spark Plug ......................................15

Starting .............................................12

Stopping ..........................................10

Storage .................................................19

Winter Operation ........................14

Fuel:

Filling Tank ...... .................................. t 1

Storage ............................................19

Type ............................................ 11

Finish:

Maintenance ........................................15

Handle:

Height Adjustment ..................... 15

Repair Parts .................................21

Lubrication:

Lubrication Chart ...................13

Engine ......................................... 14

Muffler:

Maintenance ................................15

Spark Arrester ...............................3

Oil: Level ............................................. 11

Type .......................................... 11,14

Operation:

Cultivating .....................................12

Fill Fuel Tank ....................................1!

Starting Engine ...........................12

Stopping Tines & Engine ...........10

Tilling ...............................................10

Tilling Hints ..................................12

Tine Operation .......................... 10

Transporting Tiller ...................... 11

Winter Operation ........................14

Repair Parts:

Tiller .......................................................2!-27

Engine .........................................28-33

Rules for Safe Operation .................. 2

Service & Adjustments:

Carburetor .......................................18

Handle Height ...................................I5

Side Shields ....................................11

Throttle ..........................................t8

Tines ...............................................17

V-Belt (Ground Drive) ............... t6

Wheels .............................................15

Service:

Repair Parts ...................................21-33

Service Record ............................13

Shear Pins:

Operation ...................................12

Repair Parts ................................26

Spark Plug:

Gap ............................................. 3

Maintenance ........................... 15

Storage:

Fue! System ............................... 19

Tiller ........................................... 19

Tilling ...................................................10,12

Tines:

Arrangement/Replacement ..... 17

Operation .................................. 10

Repair Parts .................................26

Shear Pins ..........................................12

Transmission:

Maintenance ................................15

Repair Parts ................................24

Troubleshooting .................................20

Transporting ...........................................11

Warranty .....................................................3

Wheels:

Removal ................................... 15

Repair Parts ..............................23

.......................................... i,, 'IMIIIIIIIII

ACCESSORIES

ii ii, i ii '111,iii, ,111.................... i i i

These accessories were available when the tiller was purchased. They are also available at most Sears Retail outlets

and Service Centers. Most Sears Stores can order repair parts for you when you provide the model number of your

tiller=

ENGINE

SPARK PLUG

, ,, ,, H,, ,,,,,_,_,,, MUFFLER

r,,,

AIR FILTER GAS CAN ENG'i'NE"'O'iL STABILIZER

TILLER PERFORMANCE ,, ,,,

_, r,T,,

FURROW OPENER L'',,' "

TILLER MAINTENANCE

TINES SHEAR PIN HAIRPIN CLIP

BELT

, ,,,,.,,,,,

iii iii ii i ii

BLY

i ii ............................................................

Your new flier has been assembled at the factory with exception of those parts left unassembled for shipping purposes To

ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely Use the

correct tools as necessary to insure proper tightness

TOOLS REQUIRED FOR ASSEMBLY OPERATOR'S POSITION (See Fig. 1)

A socket wrench set will make assembly easier Standard When right or left hand is mentioned in this manual, it

wrench sizes are listed_

(1) Utility knife

(1) Wire cutter

(1) Screwdriver

(1) Tire pressure gauge

(t) Pair of pliers

(1) 9/16" wrench

means when you are in the operating position (standing

behind tiller handles)°

FRONT

LEFT RIGHT

OPERATOR'S

POSITION

FIG. 1

CONTENTS OF HARDWARE PACK

........................... ,, ,,,,,,,,,,,,,

L_ ,i,

(2) Handle Locks

,,,, ii,,111

(1) Flat Washer 13t32 x I x 11 Ga,

i i, i iii

(2) Hairpin Clips

(1) Carriage Bolt 3/8-16 UNC x I Gr 5

i IIIIIIIH i iiiiiiiir.........

(1) Cable Clip

ii i iiiii

(1) Pivot Bolt

3/8-16 UNC Grade 5

(1) Center Locknut 3/8-16 UNC

(1) Handle Lock Lever

Extra Shear Pins & Ciips

,,11,,,,,i,............... i, , , ,........ 1,1,1 L'L_

ASSEMBLY

..................... i, , i ,,,i,i1,,,,,i,i, ,i,i1,,,,,i,,,i,ii, ii, , i ,,

UNPACKING CARTON (See Fig, 2) oGrasp handle assembly, HoIdin"up"position. Be sure

handle lock remains in gearcase notch, Slide handle

assembly into position,,

IMPORTANT; WHEN UNPACKING AND ASSEMBLING

TILLER, BE CAREFUL NOT TO STRETCH OR KINK

CABLES,,

, While holding handle assembly, cutcabletiessecuring

handle assembly to top frame and depth stake_ Let

handle assembly rest on tiller,

o Remove top frame of carton°

•Slowly ease handle assembly up and place on top of

carton,

oCut down right hand front and right hand rear' corners

of carton, lay side carton wall down.

•Remove packing material from handle assembly°

•Separate shift rod from handle assembly,

SHIFT ROD

HANDLE

ASSEMBLY

FIG. 2

INSTALL HANDLE (See Figs. 3, 4, and 5)

oInsert one handle lock (with teeth facing outward) in

gearcase notch_ (Apply grease on smooth side of

handl_ lock to aid in keeping lock in place until handle

assembly is lowered into position.)

VIEW FROM R,H. SIDE OF TILLER

\HANDLE ASSEMBLY

GEARCASE

NOTCH

HANDLE

LOCK

,_,:: .:_,_ +,j.f,_f HANDLE ASSEMBLY

",j._., _:,: "UP" POSITION

__ TIGHTENHANDLE

LOCK LEVERTO

HOLD

LOOSEN HANDLE _

LOCK LEVER TO

MOVE I

FIG. 4

.Rotate handle assembly down. Insert rear carriage bolt

first, with head of bolt on LH. side of tiller and loosely

assemble Iocknut (See Fig. 5).

= Insert pivot bolt in front part of plate and tighten.

oCut down remaining corners of carton and lay panels

flat.

= Lower the handle assembly,, Tighten nut on carriage

bolt so handle moves with some resistance. This wil!

allow for easier adjustmenL

• Place flat washer on threaded end of handle lock lever.

° Insert handle 10ck lever" through handle base and

gearcase. Screw in handle lock lever just enough to

hold lever in place.

= Insert second handle 10Ck(with teeth inward) in the slot

of the handle base (just inside of washer).

• Raise handle assembly to highest position and se-

curely tighten handle lock lever by rotating clockwise.

Leaving handle assembly in highest position will make

it easier to connect shift rod.

GEARCASE HANDLE

LOCK

REAR FLAT

CARRIAGE SLOT WASHER

BOLT _ '

HANDLE

LOCK

LEVER

HANDLE "_

BASE PIVOT

LOCKNUT BOLT

FIG. 3 FIG. 5

CONNECT SHIFT ROD (See Fig. 6)

o Insert end of shift rod farthest from bend into hole of

shift lever indicator.

• Insert hairpin clip through hole of shift rod to securer

° Insert other end of shift rod into hole in shift lever.

° Insert second hairpin clip through hole of shift rod°

ATTACHTHISEND ATTACHTHIS

TOSHIFTLEVER ENDTO SHIFT

INDICATOR LEVER _

SHIFT ROD

SHIFT

...................... i,i i,,

HAIRPIN SHIFT

CLIP LEVER

INDICATOR

SHIFT

i ii i

HAIRPIN CLIP

SHIFT ROD

FIG. 6

REMOVE TILLER FROM CRATE

,Adjust handte assembyto lowest position, Be sure lock

lever is tightened securely°

o Make sure shift lever indicator is in "N" (neutral) posi-

tion (See Fig. 6)

°Tilt tiller forward by lifting handle° Separate cardboard

cover from leveling shield.

oRotate tiller handle to the right and pull tiller out of

carton.

INSERT CABLE CLIP (See Fig. 7)

° Insert plastic cable clip into hole on the back of handle

column_ Push cables into clip.

HANDLE

COLUMN

CABLES

FIG. 7

CHECK TIRE PRESSURE

The tires on your unit were overinflated at the factory for

shipping purposes, Correct and equal tire pressure is

important for best tilling performance°

o Reduce tire pressure to 20 PSI°

HANDLE HEIGHT

• Handle height may be adjusted to better suit operator.

(See 'TO ADJUST HANDLE HEIGHT" in the Service

and Adjustments section of this manual)_

L_ ,.i ..... I' ,.... I" "'111"'11'11'""='"1'""11'1"1 ........ I1'1 I1'11"11"1'1111 , , ,I,,,,,,,I,, "1"'11'1' '

OPEF ATmON

.,, .............. ,,.. i ,,, i i, i iiiii,,i, ,i,,i,,,i,M'IIII "11'"'1''11I

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER,

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments, Save

this manual for future reference°

These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their

meaning.

T{LL|NG FORWARD NEUTRAL REVERSE CAUTION ENG1NE ENGINE

OR WARNING ON OFF

FAST SLOW

STOP O

CHOKE FUEL OtL

DRIVE _ THROTTLE

CONTROL _CONTROL

BAR

SHIFT LEVER

INDICATOR

PRIMER

DEPTH STAKE _

LEVELING _ _ _ _ _\_

SHIELD

OUTER

SIDE

SHIELD

RECOIL

STARTER

HANDLE

FIG. 8

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute,

PRIMER - pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine,

DEPTH STAKE - Controls depth at which tiller will dig

DRIVE CONTROL BAR _ Used to engage tines,

LEVELING SHIELD * Levels tilled soil.

OUTER SIDE SHIELD - Adjustable to protect small plants

from being buried.

RECOIL STARTER HANDLE - Used to start the engine,

SHIFT LEVER - Used to shift transmission gears,

SHIFT LEVER INDICATOR - Shows which gear the trans-

mission is in_

THROTTLE CONTROL - Controls engine speed..

The operation of any tiller can result in foreign objects thrown into the eyes, which can

result in severe eye damage. Always wear safety glasses or eye shields before starting

your tiller and while tilling. We recommend a wide vision safety mask over the spectacles

or standard safety glasses.

i i, i,ili,i, i i ...................................... ill ,_l,r

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and

oil or attempting to start engine_

STOPPING (See Fig. 9)

TINES AND DRIVE

-Release drive control bar to stop movement.

o Move shift lever to "N" (neutral) position.

ENGINE

oMove throttle control to "STOP" position.

o Never use choke to stop engine_

DRIVE CONTROL BAR

"ENGAGED" POSITION .THROTTLE

SHIFT

LEVER

DRIVE CONTROL BAR

"DISENGAGED" POSITION

FIG. 9

TINE OPERATION - WITH WHEEL DRIVE

• Always release drive control bar before moving shift

lever into another position.

•..... r "T"

Tine movement ts achieved by mowng shift leve to

(till) position and engaging drive control bar.

FORWARD- WHEELS ON LY/TINES STOPPED

•Release drive control bar and move shift lever indicator

to "F" (forward)position Engage drive control bar and

tiller will move forward.,

REVERSE - WHEELS ONLY/TINES STOPPED

= DO NOT STAND DIRECTLY BEHIND TILLER.,

°Release the drive control bar.

° Move throttle control to "SLOW" position.

•Move shift lever indicator to "R" (reverse) position.

= Hold drive control bar against the handle to start tifier

movement. 10

DEPTH STAKE (See Fig. 10)

The depth stake can be raised or lowered to allow you more

versatile tilling and cultivating, or to more easily transport

'our tiller°

SHALLOWES=I

TILLING

POSITION

TILLING (See Fig, 11)

o Release depth stake pin. Pull the depth stake up for

increased tilling depth. Place depth stake pin inhole of

depth stake to lock in position

.Place shift lever indicator in 'q" position,

o Hold the drive control bar against the handle to start

tilling movemenL Tines and wheels will both turn,

-Move throttle control to "FAST" position for deep tilling.

To cultivate, throttle control can be set at any desired

speed, depending on how fast or slow you wish to

cultivate.

IMPORTANT: ALWAYS RELEASE DRIVE CONTROL BAR

BEFORE MOVING SHIFT LEVER INTO ANOTHER

POSITION

DEPTH STAKE PIN

"RELEASED" POSITION

NUT "A"

"LOCKED"

POSITION

OUTER NUT "B"

SIDE SHIELD

FIG. 11

...... =,, = = ,,H, ,=.... =,, ,,,=,,,,,H,

OPERAT!ON

, = , =,m

i u u, 1, ,lu,,,H ....

TURNING • To read proper'level, tighten engine oil cap each time.

Release the drive control bar,

Move throttle control to "SLOW" position.

Place shift lever indicator in "F" (forward) position.

Tines will net turn

Lift handle to raise tines out of ground.

Swing the handle in the opposite direction you wish to

turn, being careful to keep feet and legs away from

tines.

When you have completed your turn-around, release

the drive control barand lower handle. Place shift lever

in "T" (till) position and move throttle control to desired

speed, To begin tilling, hold drive control bar against

the handle,

• Reinstall engine oil cap and tighten.

• For approximate capacity see "PRODUCT SPECIFI-

CATIONS" on page 3 of this manual. All oil must meet

A.PJ. Service Classification SF or SG.

= For cold weather operation you should change oil for

easier starting (See oil viscosity chart in the Customer

Responsibilities section of this manual),,

° To change engine oil, see the Customer Responsibili-

ties section in this manual,,

OUTER SIDE SHIELDS (See Fig. 11)

The front edges of the outer side shields are slotted so that

the shields can be raised for deep tilling and lowered for

shallow tilling to protect small plants from being buried.

Loosen nut "A" in slot and nut "B"_ Move shield to desired

position (both sides)° Retighten nuts.

OIL FILL

CAP/DIPSTICK

TO TRANSPORT

,,, =,,=,=,,=,,=1=....

CAUTION: Before lifting or transport-

ing, allow tiller engine and muffler to

cool. Disconnectsparkplugwire. Drain

gasoline from fuel tank.

.......... i, ,, i ,i iiil,,,,,,i,,llqi,

AROUND THE YARD

• Release the depth stake pin,. Move the depth stake

down to the top hole for transporting the tiller, Place

depth stake pin in hole of depth stake to lock in position,

This prevents tines from scuffing the ground.

o Place shift lever indicator in "F" (forward) position for

transporting°

•Hold the drive cont{ol bar against the handle to start

tiller movement, Tines will net turn.

•Move throttle control to desired speed,

AROUND'TOWN

° Disconnect spark plug wire,

° Drain fuel tank.

-Transport in upright position to prevent oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT

TO ENTER THE ENGINE WHEN CHECKING OR ADDING

OIL OR FUEL. USE CLEAN OtL AND FUEL AND STORE

IN APPROVED, CLEAN, COVERED CONTAINERS. USE

CLEAN FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig. 12)

•The engine in your unit has been shipped, from the

factory, already titled with SAE 30 summer weight oil,

= Be sure tiller is tevel and the area around oil fill is clean_

= Check oil level before each use,, Add oil if needed° Fill

to full line on dipstick. 11

FIG. 12

ADD GASOLINE

= Fill fuel tank Use fresh, clean, regular unleaded

gasoline. (Use of leaded gasoline wilt increase carbon

and lead oxide deposits and reduce valve life.)

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW 32°F (0°C), USE FRESH, CLEAN, WINTER GRADE

GASOLINE TO HELP INSURE GOOD COLD WEATHER

STARTING.

WARNING: Experience indicates that alcohol blended

fuels (called gasohot or using ethanol or methanol) can

attract moisture which leads to separation and formation of

acids during storage° Acidic gas can damage the fue!

system of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before

storage of 30 days or longer, Drain the gas tan k, start the

engine and let it run untit the fuel lines and carburetor are

empty_ Use fresh fuel next season. See Storage section

of this manual for additional information, Never use engine

or carburetor cleaner products inthe fuel tank or permanent

damage may occur_

&CAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to

allow for fuel expansion, if gasoline is

accidentally spilled, move machine

away from area of spill. Avoid creating

any source of ignition until gasoline

vapors have disappeared.

Do not overfill. Wipe off any spilled oil

or fuel, Do not store, spill or use gaso-

line near an open flame.

OPERATUON

i i, ,,,11

TO START ENGINE (See Fig. 7)

When starting engine for the first time or if engine has run

out of fuel, it will take extra pulls ofthe recoil starter to move

fuel from the tank to the engine.

= Make sure spark plug wire is properly connected.

• Move shift lever indicator to "N" (neutral) position..

• Place throttle controlin "FAST" po_ition.

= To start a cold engine, push primer five (5) times before

trying to start. Use a firm push. This step is not usually

necessary when starting an engine which has already

run for a few minutes,

o Grasp recoil starter handle with one hand and grasp

tiller handle with other hand. Pull rope out slowly until

engine reaches start of compression cycle (rope will

pull slightly harder at this point)°

° Pull recoil starter handle quickly. Do not let starter

handle snap back against starter.

= Allow engine to warm up for a few minutes before

engaging tines.

NOTE: In cooler weather it may be necessary to repeat

priming steps., in warmerweather over priming maycause

flooding and engine will not start° If you do flood engine,

wait a few minutes before attempting to start and do not

repeat priming steps.

PRIMER RECOIl. STARTER

HANDLE

FIG. 13

TILLING HINTS

................. ,,=,,11.........

CAUTION: Until you are accustomed to

handling your tiller, start actual field

use with throttle in slow position (m!d-

way between "FAST" and "IDLE").

, , ,i, i,,11.... i i,=

° Tilling is digging into turning over, and breaking up

packed soil before" planting° Loose, unpacked soi!

helps root growth° Best tilling depth is 4 to 6'. A tiller

will also clear the soil of unwanted vegetation, The

decomposition of this vegetable matter enriches the

soil. Depending on the climate (rainfall and wind), it

may be advisable to till the soil at the end of the growing

season to further condition the soil.

oFor easier handling of your tiller, leave about 8 inches

of untilled soil between the first and second tilling

passes. The third pass will be between the first and

second (See Fig. 14). 12

o Soil conditions are important for proper tilling° Tines will

not readily penetrate dry, hard soil which may contrib-

ute to excessive bounce and difficult handling of your

tiller° Hard soi! should be moistened before tilling;

however, extremely wet soil will "ball-up" or clump

dudng tilling° Wait until the soil is less wet in order to

achieve the best results. When tilling in the fall, remove

vines and long grass to prevent them from wrapping

around the tine shaft and slowing your tilling operation.

° Do not lean on handle° This takes weight off the wheels

and reduces traction. To get through a reaIly tough

section of sod or hard ground, apply upward pressure

on handle or lower the depth stake.

77 _1f

/i'

FIG. 14

CULTIVATING

Cultivating is destroying the weeds between rows to pre-

vent them from robbing nourishment and moisture from the

ptants. At the same time, breaking up the upper layer of soil

crust will he}p retain moisture in the soil. Best digging depth

is 1" to 3". Lower the outer side shields to protect small

plants from being buried.

= Cultivate up and down the rows at a speed which wi!)

allow tines to uproot weeds and leave the ground in

rough condition, promoting no further growth of weeds

and grass (See Fig. 15).

\_1

FIG. 15

TINE SHEAR PINS

The tine assemblies on your tiller are secured to the tine

shaft with shear pins (See 'q-INE REPLACEMENT" in the

Service and Adjustments section of this manual)°

If the tiller is unusually overloaded or jammed, the shear

pins are designed to break before internal damage occurs

to the transmission°

, If shear pin(s) break, replace only with those shown in

the Repair Parts section of this manual

................ i, , .... , ........ ii,, ,,,=....

CUSTOMER RESIPON BILUTIES

,,=,,H=................................................ ,= ' ,

SCHEDULE

REGULAR SERVICE

=, , ,= ,,= H,= ........ H,u H= HH '' =I

Check Engine 0it Level _#' _#'

=lull Ill, =!,

Change Engine Oil 1_1,2

=,H , 111 ..................

Oil Pivot Points

Inspect Spark Attester /Muffler =i

Inspect AIr Screen _'

=ui!==,=

Clean or Replace Air Cfeaner Cartridge _2

1,,,,1, ,111 ==u

Clean Engine Cylinder Fins

Replace Spark Plug _#_

1 - Chango mote often when operating under aheavy load or in high ambient temperatures,

2 - Service more often when operating in ditty or dusty conditions

GENERAL RECOMMENDATIONS

The warranty on this tiiler does not cover items that have

been subjected to operator' abuse or' negligence° To

receive fufl value from the warranty, the operator must

maintain tiller as instructed in this manual,

Some adjustments wilt need to be made periodically to

properly maintain your tiller°

All adjustments in the Service and Adjustments section of

this manual should be checked at least once each

seasom

oOnce a year you should replace the spark pfug, clean

or replace air filter, and check tines and belts for' wear.

A new' spark plug and clean air filter assure proper air-

fuel mixture and help your engine run better and last

longer,

BEFORE EACH USE

= Check engine oil level°

• Check tine operation°

, Check for' loose fasteners.

LUBRICATION

Keep unit well lubricated (See "LUBRICATION CHART").

LUBRiCATiON CHART

* THROTTLE

CONTROL

** ENGINE

* LEVELING

HINGES

* IDLER

BRACKET

WHEEL

HUB

*SAE 30 OR 10W-30 MOTOR OIL

** REFER TO CUSTOMER RESPONSIBILITIES "ENGINE" SECTION

m ,_ ..................... n,,,,, i,, ,,i

CUSTOMER RESPONSBB L TmES

,, ii,lll,r,t

Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent

accidental starting of engine.

Preventfires{ Keepthe engine free of grass, leaves, spiliedoil, orfuel. Removefuel from tank before tipping

unit for maintenance. Clean muffler area of all grass, dirt, and debris°

Do not touch hot muffler or cylinder fins as contact may cause burns.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service

classification SF, SG or SH Select the oil's SAE viscosity

grade according to your expected temperature,

SAE VISCOSITY GRACES

_F "20_ 0_ 30° 32_ 40° 60 _ B0 _ 100_

°c ._oo .{oo ._oo oo ,'o, _oo 30° 40°

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

FIG. 16

NOTE: Although multi-viscosity oils (5W-30, 10W*30, etco)

improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption when used above

32°F (0°C). Check your engine oil level more frequently to

avoid possible engine damage from running low on oil

Change the oil after every 25 hours of operation or at least

once a year ifthe tractor is not used for25 hours inone year,

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Add SAE

30 motor oil or equivalent. Tighten oil filler plug securely

each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 16 and 17)

Determine temperature range expected before oil change,

All oil must meet API service classification SF, SG or SHo

•Be sure tiller is on level surface.

-Oi! will drain more freely when warm°

.Use a funnel to prevent oil spill on tiller, and catch oil in

a suitable container_

.Remove oil drain plug and oil fill cap/dipstick, Be

careful not to allow dirt to enter the engine,

For easier removal of plug use 7/16 12 Pt. socket with

extension.

.Tip tiller forward to drain oil,

•After oil has drained completely, replace oil drain plug

and tighten securely°

• Refill engine with oil through oil fill tube. See "CHECK

ENGINE OIL LEVEL" in the Operation section of this

manual.

o,,.i

PLUG_

FIG, 17 14

AIR FILTER (See Fig. 18)

Your engine will not run properly using a dirty air filter,,

Clean the foam pre-cleaner after every 25 hours of opera*

tion or every season° Service paper cartridge every 100

hours of operation or every season, whichever occurs firsL

Service air cleaner more often under dusty conditions,,

° Remove cover screw and cover,

TO SERVICE PRE-CLEANER

• Remove foam pre-cleaner from air cleaner cover.,

°Wash it in liquid detergent and water.

o Squeeze it dry in a clean cloth,

• Saturate it in engine oil Wrap it in clean, absorbent

cloth and squeeze to remove excess oil

o If very dirty or damaged, rep{ace pre-cieaner.

•Reinstall pre-cleaner into air cleaner cover.

.ReinstalI cover and secure screw.

TO SERVICE CARTRIDGE

= Carefully remove cartridge to prevent debris from en-

tering carburetor. Clean base carefully to prevent

debris from entering carburetor._

° Clean cartridge by tapping gently on flat surface° Ifvery

dirty or damaged, replace cartridge.

. Reinstall cartridge, cover with pre-cleaner and secure

with screw,

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS

KEROSENE, ARE NOT TO BE USED TO CLEAN THE

CARTRIDGE, THEY MAY CAUSE DETERIORATION OF

THE CARTRIDGE. DO NOT OIL CARTRIDGE DO NOT

USE PRESSURIZED AIR TO CLEAN OR DRY CARTRIDGE°

FOAM

PRECLEANER

COVER

AIRCLEANER

CARTRIDGE

COVER

SCREW

FIG. 18

COOLING SYSTEM (See Fig. 19)

Your engine is air cooled° For proper engine performance

and long life keep your engine clean°

• Clean air screen frequently using a stiff-bristled brush°

° Keep cylinder fins, levers, and linkage free of dirt and

chaff..

MUFFLER .<j---_, _ CYLINDER FINS

AIR SCREEN

FIG. 19

,IH ,I,H,I,

CUSTO ESPONSBBmLmTIES

, ,,,, , ii,i i ,i ,ml,m i1,1 ,,, m,ii

MUFFLER TRANSMISSION

Do not operate tiller without muffler.. Do not tamper with

exhaust system. Damaged mufflers or' spark arresters

could create a fire hazard° Inspect periodically and replace

if necessary, if your engine is equipped with a spark

arrester screen assembly, remove every 50 hours for

cleaning and inspection Replace if damaged

SPARK PLUG

Replace spark plugs at the beginning of each tilling season

or after every 50 hours of use, whichever comes first. Spark

plug type and gap setting is shown in "PRODUCT SPECI-

FICATIONS" on page 3 of this manual.

Your transmission is sealed and will only require lubrication

if serviced,

CLEANING

° Clean engine, wheels, finish, etc. of alt foreign matter.

oKeep finished su daces and wheels free of all gasoline,

oil, etc..

oProtect painted surfaces with automotive type wax..

We do not recommend using a garden hose to clean your

unit unless the muffler, air filter and carburetor are covered

to keep waterouL Water in engine can result in a shortened

engine life

$E ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into

contact with plug,

, ,r_r ,,r, i

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions,

Handle height will be different when tiller digs into soil,

= First loosen handle lock lever,

= Handle can be positioned at different settings between

"HIGH" and "LOW" positions,

. Retighten handle lock lever securely after adjusting,

HANDLE (HIGH

)

HANDLE

LOCK

LEVER

HANDLE (LOW

POSITION)

FIG. 20

TIRE CARE

_ CAUTION: When mounting tires, un-

less beads are seated, overinflation

can cause an explosion,

,, , i, , ii , ,

• Maintain 20 pounds of tire pressure. If tire pressures

are not equal, tiller will pull to one side,

• Keep tires free of gasoline or oil which can damage

rubber° 15

l'O REMOVE WHEEL (See Fig. 21)

o Place blocks under transmission to keep tiller from

tipping.

o Remove outer side shield by _emoving nuts"A" and"B"

- Remove inner side shield by removing nuts "C" and

"D"_

-Remove hairpin clip and clevis pin from wheel

o Remove wheel and tire_

-Repair tire and reassemble°

HAIRPIN

CLIP

INNER SIDE

SHIELD

OUTER

NUT "B" SIDE

SHIELD

FIG. 21

,iiiiil,,,u,,ul , ,,11,,i

SERVmCE AN ADJUSTMENTS

i1,,

TO REMOVE BELT GUARD (See Fig. 22)

•Remove L.H, inner and outer side shields (See "TO

REMOVE WHEEL" in this section of this manual),

o Remeve hairpin clip andclevis pinfromleffwheeL Pull

wheef out from tiller about t inch

o Remove two (2) cap nuts and washers from side of belt

guard,

o Remove hex nut and washer from bottom of belt guard

(located behind wheel)

• Pull belt guard cut and away from unit

. Replace belt guard by reversing above procedure

BELT GUARD

/_z_ _\

CAP NUT _l_ _

AND WASHER

CAP NUT

AND WASHER

=o, x.o,

WASHER

"" BEHIND

TIRE)

\HAIRPIN CLIP AND

CLEVIS PiN

FIGo 22

TO REPLACE GROUND DRIVE BELT (See

Figs. 22 and 23)

o Remove belt guard (See''TO REMOVE BELT GUARD"

in this section of this manual)

• Loosen belt guides "A" and "B" and atso nuts "C" and

° Remove old belt by slipping from engine pulfey first,

= Place new belt in groove of transmission pulley and

into engine pulley BELT MUST BE IN GROOVE ON

TOP OF IDLER PULLEY NOTE POSITION OF BELT

TO GUIDES,

o Tighten belt guides "A" and "B" and nuts "C" and "D",

=Check belt adjustment as described below

,Replace belt guard.

, Reposition wheel and replace clevis pin and hairpin

ciip_

-Replace inner and cuter side shields.

GROUND DRIVE BELT ADJUSTMENT (See

Fig. 23)

For proper belt tension, the extension spring should have

about 5/8 inch stretch when drive control bar is in "EN-

GAGED" position This tension can be attained as follows:

• Loosen cable clip screw securing the drive control

cable.

, Slide cable forward for less tension and rearward for

more tension until about 5/8 inch stretch is obtained

while the drive control bar is engaged..

Tighten cable clip screw securely..

ENGINE

PULLEY

BELT CABLE CLiP

GUIDE "A' SCREW

BELT CONTROL

CABLE

IDLER

PULLEY TRANSMISSION

PU LLEY

FIG. 23_

EXTENSION

SPRING

=,n, = , ,=,,,,,,===,_

SERVICE AND ADJUSTMENTS

TINE REPLACEMENT (See Figs. 24, 25 and 26)

,,i ,11 ii i1,1.i,. ,,

gloves or other protection when han-

dling tines.

A badly worn tine causes'your ii'i'ler to work harder and dig

mote shallow., Most important, worn tines cannot chop and

shred organic matter as effectively nor bury it as deeply as

good tines A tine this worn needs to be replaced.

NEW TINE WORN TINE

FIG. 24

- To maintain the superb tilling performance of this

machine the tines should be checked for' sharpness,

wear, and bending, particularly the tines which are next

to the transmission. If the gap between the tines

exceeds 3-I/2 inches they should be replaced or

straightened as necessary

o New tines should be assembled as shown in Fig. 26.

Sharpened tine edges will rotate rearward from above..

TINE 1

[

3-1t2" MAX--4

_TINE

FIG. 25

HAIRPIN CLIP

COUNTER

TINE

ROTATION

HAIRPIN CLIP

SHARP EDGE

SHEAR PiN

SHEAR PIN

EDGES

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

(See Fig. 27)

The throttle control has been preset at the factory and

adjustment should not be necessary° If adjustment is

necessary, proceed as follows:

o With engine not running, move remote throttle control

[ever to "FAST" position.

° If throttle lever on engine touches high speed stop, no

further adjustment is necessary, tf throttle lever does

not touch high speed stop, continue with adjustment

procedure_

• Loosen cable clamp screw°

o Move throttle lever up until ittouches high speed stop,

and hold in this position_

oTighten cable clamp screw securely..

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust-

ment should not be necessary, However, engine perfor-

mance can be affected by differences in fuel, temperature,

altitude or load, If the carburetor does need adjustment,

contact your nearest authorized service cente r/department

IMPORTANT: NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED, OVERSPEEDING THE ENGINE ABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS_ IF YOU THINK THE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT

AND EXPERIENCE TO MAKE ANY NECESSARY

ADJUSTMENTS

HIGH SPEED STOP \

THROTTLE /

CABLE

CLAMP

SCREW

THROTTLE

LEVER

FIG. 27

Immediately prepare your tiller' for storage at the end of the

season or if the unit will not be used for 30 days or more.

= ,,,,i .... i,

CAUTION: Never store the tiller with

gasoline in the tank inside a building

where fumes may reach an open flame

or spark. Allow the engine to cool

before storing in any enclosure,

..... i,,,,,i ........................

TILLER

oClean entire tiller'(See "CLEANING" in the Customer

Responsibilities section of this manual).

- Inspect and replace belts, if necessary (See belt re-

placement instructions in the Service and Adjustments

section of this manual),

o Lubricate as shown in the Customer Responsibilities

section of this manual,,

• Be sure that all nuts, bolts and screws are securely

fastened° Inspect moving parts fordamage, breakage

and wear'. Replace if necessary.

•Touch up al] rusted or chipped paint surfaces; sand

lightly before painting,.

ENGmNE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM

DEPOSITS FROM FORMING IN ESSENTIAL FUEL

SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL

FILTER, FUEL HOSE, OR TANK DURING STORAGE_

ALSO, EXPERIENCE INDICATES THAT ALCOHOL

BLENDED FUELS (CALLED GASOHOL OR USING

ETHANOL OR METHANOL) CAN ATTRACT MOISTURE

WHICH LEADS TO SEPARATION AND FORMATION OF

ACIDS DURING STORAGEI ACIDIC GAS CAN DAMAGE

THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

= Drain the fuel tank.

o Start the engine and let it run until the fuel lines and

carburetor are empty.,

.Never use engine or carburetor cleaner products in the

fuel tahk or permanent damage may occur.

= Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during stor-

age_ Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stabilizer

container. Run engine at least 10 minutes after adding

stabilizer to allowthestabilizerto reach the carburetor. Do

not drain the gas tank and carburetor' if using fuel stabilizer.

ENGINE OIL

Drain eli (with engine warm) and replace with clean oil.

(See "ENGINE" in the Customer Responsibilities section of

this manual)_

CYLINDERS

oRemove spark plug

oPour1 ounce (29 ml) of oil through spark plug hole into

cylinder°

o Pull starter' handie slowly several times to distribute oil

o Replace with new spark plug.

OTHER

• Do not store gasoline from one season to another.

. Replace your' gasoline can if your can starts to rust_

Rust and/or dirt in your' gasoline will cause problems.

-If possible, store your unit indoors and cover it to give

protection from dust and dirt.

,, Cover your unit with a suitable protective cover' that

does not retain moisture. Do not use plastic. Plastic

cannot breathe which allows condensation to form and

will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE

AND EXHAUST AREAS ARE STILL WARM,

I'H'""H" I" I" I

TROUBLESHOOTING POINTS

,, iii i, i,i P,,,ll , , ,, , LILI,]I','U"I'Nr,L',1,', ....................

PROBLEM CAUSE CORRECTION

Wli! not start

i,i ii i , ,,===,1

Hard to start

i, H,,

Loss of power

Engine overheats

Excessive bounce/

difficult handling

Soil balls up or clumps

Engine rune but tiller

won't move

Engine runs but labors

when tilling

Tines will not rotate

1 Out of fuel

2 Engine not "CHOKED" propedy

3 Engine flooded

4 Dirty air cleaner

5 Water in fuel

6 Clogged fuel tank

7Loose spark plug wire

8 Bad spark plug ar improper gap

9 Carburetor out of adjustment,

10 Oil soaked air filter

t Throttle contro} not sat properly

2 Dirty air cleaner

3 Bad spark plug or improper gap

4 State or dirty fuel

5Loose spark plug wire

6 Carburetor out of adjustment

ii H,"H',N

1 Engine is overloaded

2 Dirty air cleaner

3 Low oil tevelfdtrty oil

4 Faulty spark plug

5 Oil in fuel

6 Stale or dirty fue}

7Water in fuel

8 Clogged fuel tank

9 Spark plug wire loose

10 Dirty engine air screen

11 Dirty/clogged muffler,

t2 Carburetor out of adiustment,

13 Poor compression

, 'H,H"" I","

1Low oil level/dirty oil

2 Dirty engine air screen

3 Dirty engine

4 Partially plugged muffler

5 Improper carburetor adjustment

i, i , i ll,l,,i,,

1 Ground too dry and hard

i i i, :::::::::::::::::::::::::::::::::::

1 Ground too wet.

1 Drive control bar is not engaged

2 V-bait not correctly adjusted

3 V-belt Isoff pulley(s)

•1Tilling too deep

2 Throttle control not properly adjusted

3 Carburetor out of adjustment

i ,, ,,IHI '"HI'H ........ I ' I .................

1 Shear pin(s) broken

I, Fill fueftank

2See '3"0 START ENGINE" in Operation section

3 Wait several minutes before attempting to start

4 Clean or replace air cleaner cartridge

5 Drain fuel tank and carburetor, and refitl tank with fresl_

gasoline

6 Remove fuel tank and clean

7 Make sure spark plug wire is seated properly on plug

8 Replace spark plug or adjust gap

9 Make necessary adjustments

10 Replace air filter

t Place throttle control in 'FAST" position

2 Ciean or replace air cleaner cartridge

3 Repiace spark plug or adjust gap

4 Drain fuel tank and refill with fresh gasoline,

5 Make sure spark plug wire is seated properly on plug

6 Make necessary adjustments

1 Set depth stake for shallower tilling

2Clean or replace air cleaner cartridge

3 Check oil level/change oil

4 Clean and regap or change spark pSug

5 Drain and clean fuel tank and refill, and clean carburetor

6 Drain fuel tank and refill with fresh gasoline,

7 Drain fuel tank and carburetor, and refill tank with fresh

gasoline

8 Remove rue{ tank and clean

9 Connect and tighten spark plug wire

10 Clean engine air screen

1 ! Clean/replace muIfler

12 Make necessary adjustments

!3 Contact an authorized service center/department

i i i ii i

1 Check oil level/change oil

2, Clean engine air screen,

3, Ctean cylinder fins, air screen, and muffter area

4 Remove and clean muffler

5 Adjust carburetor to richer position

Moisten ground or wait for more favorable soil

conditions,

Wait for more favorable soil conditions,

t Engage drive control

2Inspect/adjust V-belt

3inspect Vobelt

1 Set depth stake for shallower tilling,

2 Check throttle control setting

3 Make necessary adjustments

1 Repiace shear pin(s)

REPARRPARTS

HANDLES

TALLER - - MODEL NUMBER 917.293650

_ _--.:,_ -,'_7-.- _-

•t;% ,29

\23

31 \\

\k..

KEY

NO,

PART

NO.

127012X

141406

110673X

1272"54X

6712J

137119

110641 X

71191008

72010520

110646X

STD624003

81328

110741X

109313X

110702 X

STD533710

109229X

STD541437

DESCRIPTION

Throttle, Control

Grip, Handle

Grommet, Handle

Bar, Drive Control Assembly

Cap, Vinyl

Panel, Control

Bushing, Split

* Screw, Pan Head #10-24

* Bolt, 5/16-18 x 2-1/2

Handle, Grip

* Clip, Hairpin

Bolt, Shoulder

Handle, Shift

Grommet, Rubber

Rod, Shift

*Bolt, Carriage 3/8-16 x ! Gr. 5

Lock, Handle

* Nut, Centerlock 3/8-16

KEY PART

NO. NO,

19 19131611

20 109228X

21 150258

22 121145X

23 86777

24 9484R

25 73970500

26 110675X

27 STD541025

28 STD551125

29 STD541462

31 150696

DESCRIPTION

Washer 13/32 x 1 x tl Gao

Lever, Lock, Handle

Handle, Assemble

Clip, Plastic, Cable

Screw, Hex, Washer Hd, Slotted

#10-24 x 1/2

Clip

Locknut, Hex, Flange

Clutch, Cable

* Nut, Hex 1/4-20

* Washer', Lock 1/4

*Nut, Keps #10-24

Bolt, Pivot

* STANDARD HARDWARE - - PURCHASE LOCALLY

NOTE: All component dimensions given in UoS. inches.

1inch = 25.4 mm

REPAURPARTS

TILLER - - MODEL NUMBER 917.293650

MAINFRAME, LEFT SIDE

KEY PART DESCRIPTION

NO. NO.

1 STD54!431 Nut, Keps 5/t6-18

2 STD551137 *Washer, Lock 3/8

3 STD541037 *Nut, Hex 3/8-16

4 74930568

5 154734

6 110111X

7 STD532505

8 8700J

9 86777

Bolt, Hex 5/16-18 x 4-1/4

Screw Shift Lever

Lever, Shift

* Bolt, Carriage 1/4-20 x 1/2 Gr. 5

Plate, Shift indicator

Screw, Hex, Washer Head, Slotted

#10-24 x 1/2

Clip

* Washer, Lock 1/4

* Nut, Hex 1/4-20

* Screw, Set, 5/16-t8 x 3/8

Spacer, Split 0°327 x 0.42 x 2.68

* Washer 11/32 x 11/16 x 16 Ga..

Sheave, Transmission

* Nut, Hex 5/16-18

Ring, Retainer

Guard, Pinch Point

Spacer, Split 0.327 x 0_42 x I 688

Nut, Cap 5/16-18

Tire

Rim

Tire Valve

Rivet, Drilled

* Clip, Hairpin

Guard, Belt

Beft, V

Pulley, Idler

10 9484R

11 STD551125

12 STD541025

13 23230506

14 120938X

15 STD551031

16 145102

17 STD541031

19 12000028

20 !10653X

21 145216

22 104214X

23 5015J

128952

795R

24 126875X

25 STD624003

26 !31159X574

27 132801

28 104679X

22 23

KEY PART DESCRIPTION

NO. NO,

29 12000032 Ring, Klip

30 105611X Bracket, Idler

31 102384X Bolt, Hex 5/16-16 ×12

32 10214IX Shaft, Idler Arm

33 STD523710 * Bolt, Hex 3/8-16 x 1

34 102383X Counterweight, L.Ho

35 74760532 Bolt, Hex 5/16-18 x 2

36 102331X Bracket, Reinforcement, L..H.

37 130812 Sheave, Engine

38 145822 Stud, Guard Belt

39 140062 Cap, Plunger

41 19111610 Washer 11/32 x 1 x 10 Ga

42 15t004 Spacer

43 69t 80 Nut Lock #10-24

*STANDARD HARDWARE - - PURCHASE LOCALLY

NOTE: All component dimensions given in U.S. inches°

1 inch = 25.4 mm

REPAIR PARTS

TILLER - - MODEL NUMBER 917.293650

MAINFRAME, RIGHT SIDE

t3\

KEY

NO.

PART

NO.

157976

73970500

STD551031

74760512

102332X

74760532

102173X

STD551137

STD541037

74760524

STD624003

DESCRIPTION

Bumper

Locknut, Hex, Flange 5116-18

* Washer 11/32 x 11/16 x 16 Ga

Bolt, Hex 5/16-18 x 3/4

Bracket, Reinforcement

Bolt, Hex 5/16-18 x 2

Counter Weight, R.H.

* Washer, Lock 3/8

* Nut, Hex 3/8-16

Bolt, Hex 5/16-18 x 1-1/2

* Clip, Hairpin

KEY PART DESCRIPTION

NO, NO.

t2 126875X Rivet, Drilled

13 5015J Tire

128952 Rim

795R Tire Valve

14 STD541431 * Nut, Keps 5/16-18

15 ...... Engine, (See Breakdown)

Craftsman Model No. 143.976001

* STANDARD HARDWARE - -PURCHASE LOCALLY

NOTE: All component dimensions given in U.SJnches.

t inch = 25..4 turn

REPAnB PARTS

TRANSMISSION

TgLLER -- MODEL NUMBER 9'17.293650

KEY PART

NO. NO.

1 154354

2 150698

3 106211X

4 5020J

5 1370H

6 137335

7 145101

8 4895H

9 154467

10 7392M

11 100371K

12 106160X

13 142145

'14 8353J

15 12000039

!6 154466

18 4358J

19 12000040

20 I02114X

21 102115X

22 6803J

23 102111X

24 STD551143

DESCRIPTION

Transmission Assembly

(Includes Key Nos. 2-52)

Gearcase, L.H..w/Bearing

(includes Key No. 4)

Gasket, Gearcase

Bearing, Needle

Washer, Thrust 5/8 x 110 x 1/32

Pinion, Input

Shaft, Input

Bearing, Needle

Washer, Seat

Bal!, Steel

Spring, ShAft, Fork

O-Ring

Arm, Shift

Fork, Shift

Ring, Klip

Shaft, Shift

Washer

Ring, Klip

Gear, Assembly, Reverse Idler

(Includes Key Nos. 21 and 22)

Gear, Reverse Idler

Bearing, Needle

Shaft, Reverse Idler

* Washer, Lock 7/16

KEY PART

NO. NO.

25 STD541143

27 143009

28 106390X

29 102134X

30 150737

31 143008

32 106388X

33 102121X

34 102112X

35 102101X

36 154355

37 4422J

38 154356

39 105345X

40 105346X

41 8358J

42 4220R

43 106146X

44 155236

48 150700

49 132688

50 106147X

51 17720408

52 73220500

53 122204X

-- 6066J

DESCRIPTION

* Nut, Hex 7/16-20

Bearing, Shaft, Ground Drive LrH.

Spacer 0.765 x 1.125 x 1.23

Chain #35-50 Pitch

Ground Shaft Assembly

Bearing, Shaft, Ground Drive R.H.

Spacer 070 x 1.00 x 1.150

Sprocket and Gear Assembly

Shaft, Reduction (2rid)

Screw, Whiz, Lock 5/16-18 x 3-t/2

Sprocket Assembly w/Bearing

(lncfudes Key Nos. 37 and 38)

Bearing, Needle

Sprocket, Tine

Gear, Ciuster, Red 1st & 2rid

Gear, Reverse

Shaft, Reduction (1st)

Washer, Thrust

Spacer 1.0t x 1_75 x 0_760

Seal, Asm_ Oil

Gearcase, R.Ho w/Bearing

(Includes Key No. 8)

Shaft, Tine

Chain, Roller #50450 Pitch

Screw 1/4-20 x 1/2

* Nut, Hex 5/16-18

Bearing Kit, Tine Shaft

Grease, Plastilube #I

* STANDARD HARDWARE - - PURCHASE LOCALLY

NOTE: All component dimensions given in U.S. inches°

1 inch = 25.4 mm

REPAIR PARTS

TINE SHIELD

TILLER -- MODEL NUMBER 917.293650

24 23

25 16

29 1

KEY PART

KEY PART DESCRIPTION NO. NO.

NO. NO. 18 STD532512

198000129 Nut, Flange 5/t6-18 t9 102701X

2104086X574 Shield, Side, Outer L.H. 20 STD541037

38393J Pin, Stake, Depth 21 102156X

4 12000036 Ring, Ktip 22 74930632

5 STD533107 * Bolt, Carriage 5/16-18 x 314 Gr5

6 8394J Spring 23 4440J

24 72140404

7 8392J Bracket, Latch 25 6712J

8 109230X Spring, Depth Stake 26 109227X

9 124289X574 Shield, Tine 27 102695X574

10 STD533110 * Bolt, Carriage 5/16-18 x 1 Gr. 5

11 STD541031 *Nut, Hex 5/16-18 28 120588X

12 STD551131 *Washer, Lock 5/16 29 124309X574

13 72110510 Bolt, Carriage 5/16-18 x 1-t/4 30 73970500

14 124311X Bracket, Shield Tine

15 104101X574 Shield, Side, Outer R.H.

16 73510400 Nut, Hex 1/4-20

DESCRIPTION

* Bolt, Carriage 1/4-20 x 1-1/4 Gr. 5

Grip

* Nut, Hex 3/8-16

Stake, Depth

Bolt, Hex 3/8-16 x 2

Hinge

* Bolt, Carriage 1/4_20 x 1/4

Cap, Vinyl

Pad, Idler

Shield, Leveling

Pin, Hinge

Shield, Side

Locknut, Hex, F_ange

* STANDARD HARDWARE -- PURCHASE LOCALLY

NOTE: All component dimensions given in U_S. inches,

1inch = 25r.4 mrn

REPABR PARTS

TINE ASSEMBLY

TILLER -- MODEL NUMBER 917.293650

11 "\

KEY

NO,

PART

NO.

4459J

132673

6554J

STD624008

132727

73610600

STD551137

DESCRIPTION

Tine, Outer, Loll..

Pin, Shear

Tine, Inner, L,.H.

* Clip, Hairpin

Assembly, Hub and Plate, Loll.

Nut, Hex 3/8-24

* Washer, Lock 3/8

KEY PART

NO. NO,

8 74610616

9 4460J

!0 t32728

tl 6555J

DESCRIPTION

Bolt, Hex 3/8-24 x 1

Tine, Outer, R.Ho

Assembly, Hub and Plate, RH

Tine, Inner, R.Ho

* STANDARD HARDWARE - - PURCHASE LOCALLY

NOXE: All component dimensions given in U.S. inches,

1 inch = 25.4 mm

REPAIR PARTS

DECALS

TILLER -- MODEL NUMBER 917.293650

°\ ©

KEY PART

NO. NO.

1 158095

2 145023

3 157982

4 157983

5 137538

6 120431X

7102180X

8 157984

9 120075X

-- 158309

-- 158310

DESCRIPTION

Decal, Logo

Decal, Description

Decal, Caution, Drive Control

Decal, Hand Placement

Decal, Shift Indicator

Decal, Ccu. Tines Rot. Tines

Decal, Warning, Rotating Tines

Manual, Owner's (English)

Manual, Owner's (Spanish)

REPARR PARTS

TILLER - - MODEL NUMBER 917.293650

ENGINE, CRAFTSMAN -- MODEL NUMBER 143.976001

310 -- 305\.,

309

308

307

254

130

416

120

238

240

245

245A 250

251

REPAIR PARTS

TILLER -- MODEL NUMBER 917.293650

ENGaNE, CRAFTSMAN -- MODEL NUMBER 143.976001

30l

400¸

lOO 25A

2go

\292

285

370A

261 261A I

2O9

390

287

327

REPAnR PARTS

TBLLER -- MODEL NUMBER 9'17.293650

ENGINE, CRAFTSMAN -- MODEL NUMBER 143.976001

KEY PART

NO. NO.

1 36866

2 26727

14 28277

15 30589

16 36618

17 36700

18 651028

19 36710

20 32600

25 36621

25A 36622

26 30200

30 34740

35 29826

36 29918

37 29216

38 29642

40 40004

4O 40OO5

41 36070

41 36071

42 40006

42 40007

43 20381

45 32875A

46 32610A

48 35616

49 36611

50 36620

60 36623

64 650738

65 30200

69 36624

70 36625

72 27642

75 27897

80 30574A

81 30590A

82 30591

83 36057

86 650488

89 610961

90 611205

92 650815

93 6508'16

100 34443A

101 610118

103 651007

110 36054

119 36719

120 36721

125 36471

125 36472

126 29314B

t26 29315C

130 650912

130A 65O999

135 34645

150 31672

151 31673

153 36649

154 650913

155 35624A

157 650914

158 36629

159 35626

160 36630A

161 651008

KEY PART

DESCRIPTION NO. NO.

Cylinder (lnci 2, 20 & 72) 173 36675A

owel Pin 178 650852

Washer 182 650451

Governor Rod 184 26756

Governor Lever 185 36631

Governor Lever Clamp 186 36711

Screw, TorxT_15, 8-32 x 3/8" 200 36736

Extension Spring

Oil Seal 206 610973

Air Baffle (Left) 207 36632

Air Baffle (Right) . 209 650821

Screw, 10-24-x 9/16 210 27793

Crankshaft 211 28942

Screw, 10-32 x 3/4" 223 650451

Lock Washer 224 36581

Lock Nut, I0-32 238 28820

Retaininq Rinq 239 27272A

Piston Pin & Ring Set (Std.) 240 36633

Piston, Pin & Ring Set (.010" OS) 245 36046

Piston & Pin Ass'y (Std) (Incl. 43) 245A 36634

Piston & Pin Ass'_/ 250 36635A

(.010" OS) (IncL 43) 251 650886

Ring Set (St&l, 252 650821

Ring Set (_010 OS) 253 36701

Piston Pin Retaining Ring 254 36702

Connecting Rod Ass'y 260 36992

(lnct 46 & 49) 261 651008

Connecting Rod Bolt 261A 650821

Valve Lifter 262 651008

Oil Dipper 275 36759

CamsHaft (lncl. 253 & 254) 277 650988

Blower Housing Ex!ension 285 35985B

Screw, 1/4-20 x 5/8 287 651008

Screw, 10-24 x 9/16" 290 30705

* Cylinder Cover Gasket 292 26460

Cyl_der Cover (Incl 75 thru 83) 298 650665

uKt urain l-'lug 300 36875

Oil Seat 301 36246

Governor Shaft 305 36877

Washer 307 35499

Governor Gear Ass'y (Incl. 81) 308 36651

Governor Spool 309 6510tl

Screw, 1/4-20 x 1-1/4" 310 36878

Flywheel Key 313 34080

Flywheel 325 29443

Belteville Washer 327 35392

Flywheel Nut 340 36876

Solid State ignition 341 36644

Spark Plug Cover 342 651010

Screw, Torx T-15, 10-24 x 15/16" 342A 650738

Ground Wire 370A 36261

* Cylinder Head Gasket 380 640025

Cylinder Head 390 590704

Exhaust Valve (Std.) (Incl. t51) 400 36720

Exhaust Valve (1/32" OS)

(IncL. 151) 416 36085

Intake Valve (Std.) (Incl. 151)

Intake Valve (1/32" OS) (Incl. 151) 417 650760

Screw, 5/16-18 x 1q/2" 600 651013

Scr_ew,5/16-18 x 2_4t/64" 900

Resistor Spark Plug (RN4C) 900

Valve Spring

Valve Spring ,Cap

Push Rod G-uiae

Rocker Arm Stud

Rocker Arm

Nut, I/4-28

Push Rod

* Rocker Arm Cover Gasket

Rocker Arm Cover

Screw, 1/4-20 x 3t/64" 3O

DESCRIPTION

Breather Tube

Nut, 1/4-20 1"

Screw, 1/4-20 x

* Carburetor To Intake Pipe Gasket

Intake Pipe

Governor Link

Control Bracket

#ncL 206, 210 & 211)

erminal

Throttle Link

Screw, 10-32 x 1/2"

Conduit Clip

Screw, 10-32 x 3/8"

Screw, 1/4-20 x 1"

* Intake Pipe Gasket

Screw, 10-32 x 1/2

* Air CIeaner Gasket

Air Cleaner Body (Incl 239)

Air Cleaner Filter

Air Cleaner Cove_ P°fy)

_]cing Nut

rew, 10-32 x 1/2"

Compression Release Weight

Compression Release Spring

Blower _ousing

Screw, 1/4-20 x 31/64"

Screw, 10-32 x 1/2"

Screw, 1/4÷20 x 31/64"

Muffler

Screw, 1/4-20 x 2-9/32"

Starter Cup

Screw_ 1/4-20 x 31/64"

Fuel Line

Fuel Line Clamp .

Screw, 1/4-15 x 3/4

Fuel Tank 292 & 30't )

Fuel Cap (Incl.

Oil Fill Tube

"O" Ring

Fill Tube Clip ,,

Screw, 10-32 x 15/16

Dipstick

Spacer

Wire Clip

Starter Pluq

Fuel Tank Bracket (Upper)

Fuel Tank Bracket (Lower)

Screw, 1/4-20 x 7/8"

Screw, 1/4-20 x 5/8"

Lubrication Decal

Carburetor (Incl 184)

Rewind Starter

Gasket Set

_ncl Items Marked * in Notes)

park Arrestor Kit

(lncL 417) (Optional)

Screw, 8-32 x 3/8"

Washer

Replacement Engine - None

Replacement S/I_ 754295,

order from 71-999

RPM High 3050 to 3350

RPM Low 1650 to 1950

(NOTE_ This engine could have been built with 590746

starter,)

NOTE: All component dimensions given in U.S. inches

1 inch = 254 mm

REPAIR PARTS

TILLER --MODEL NUMBER 917.293650

ENGnNE, CRAFTSMAN -- MODEL NUMBER 143.976001

KEY PART

NO. NO. DESCRIPTION

640025

1 631615

2 631767

4 631184

5 631183

6 631036

7 650506

16 632164

17 650417

20A

630766

640018

640053

631867

631024

632019

631028

631021

631022

36045

640019

632547

640015

27110

630748

631027

Carburetor

(lncI 184 or Engine Parts list)

Throttle Shaft & Lever Assembly

Throttle Return Spring

Dust Seal Washer

Dust Seat (Throttle)

Throttle Shutter

Shutter Screw

Fuel Fitting

Throttle Crack Screw/

Idle Speed Screw

Tension Spring

Idle Restdctor Screw

Idle Restrictor Screw Cap

Float Bowl

Float Shaft

Float

Float Bowl "O" Ring

Inlet Needle, Seat, & Clip (Incl. 31)

Spring Clip

Primer Bulb/Retainer Ring

Main Nozzle Tube

"O" Ring, Main Nozzle Tube

High Speed Bowl Nut

Bowl Nut Washer

Welch Plug, Idle Mixture Well

Welch Plug, Atmospheric Vent

KEY

NO.

PART

NO.

590704

590599A

590600

590696

590601

590697

590698

590699

590700

590705

590535

590701

,DESCRIPTION

Recoil Starter

Spring Pin (Incl, 4)

Washer .................................................

Retainer

Washer

Brake Spring

Starter' Dog

Dog Spring

Pulley & Rewind Spring Ass'y.

Starter Housing Ass'y..

Starter' Rope ( 98" X 9/64" dia.)

Starter Handle

_]--, 31

KEY

NO.

PART

NO.

590746

590599A

590600

590679

590601

590678

590680

590412

590681

590747

590535

590701

DESCRIPTION

Recoil Starter

Spring Pin (lncl. 4)

Washer

Retainer

Washer'

Brake Spring

Starter Dog

Dog Spring

Pulley & Rewind Spring Assembly

Starter Housing Assembly

Starter Rope

(Length 98" x 9/64" dia.)

Starter Handle

MODEL NO=

917.293650

iF YOU NEED

REPAIR SERVmCE

OR PARTS:

FOR REPAIR SERVICE, CALL

THIS TOLL FREE NUMBER:

1-800-4-REPAIR

(1-800-473-7247)

FOR REPLACEMENT PARTS

INFORMATION AND

ORDERING, CALL THIS

TOLL FREE NUMBER:

1-800-FON-PART

(1-800-366-7278)

8.0 HP

17 INCH TINE WIDTH

EAR T! TILLER WITH

OOLINTEFI ROTATING TINES

Each tiIler has its own model number. Each engine has its own model

number.

The model number for your tiller will be found on a plate attached to the

top of the transmission.

The model number for your engine will be found on the blower housing of

the engine.

All parts listed herein may be ordered from any Sears, Roebuck and Co.

Service Center!Department and most Retail Stores,

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOW-

ING INFORMATION:

°PRODUCT -REAR TINE TILLER

oMODEL NUMBER - 917.293650

oENGINE MODEL NUMBER - 143,976001

• PART NUMBER

oPART DESCRIPTION

Your Sears merchandise has added value when you consider Sears has

service units nationwide staffed with Sears trained technicians._ profes-

sional technicians specifically trained to insure that we meet our pledge

to you, we service what we sell.

..... ,,,- i i,, =1 ,=,1

.................................... i,i i,

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

i ,iiiii ,i ,,, i,i ,I,i ...... ii

158309 Rev. 4 4+28,97TR PRINTED INTHE U,S,Ao

Craftsman 917293650 User Manual Rear Tine, Gas Tiller Manuals And Guides L0804441

CRAFTSMAN Rear Tine, Gas Tiller Manual L0804441 CRAFTSMAN Rear Tine, Gas Tiller Owner's Manual, CRAFTSMAN Rear Tine, Gas Tiller installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation