Craftsman 917298353 User Manual TILLER Manuals And Guides L0804229

CRAFTSMAN Front Tine, Gas Tiller Manual L0804229 CRAFTSMAN Front Tine, Gas Tiller Owner's Manual, CRAFTSMAN Front Tine, Gas Tiller installation guides

User Manual: Craftsman 917298353 917298353 CRAFTSMAN TILLER - Manuals and Guides View the owners manual for your CRAFTSMAN TILLER #917298353. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman TILLER Manual

Open the PDF directly: View PDF .
Page Count: 32

MODEL NO,

917o298353

Caution:

Read and follow

all Safety Rules

and Instructions

Before Operating

This Equipment

wiii,,,i i i, i i

5°0 HP

24 HNCH TNNE DTH

FRONT TINE T_LLER

oAssembBy

Operation

Customer ResponsibiBities

,Service and Adjustments

oRepair Parts

Sears, Roebuck and Co., Hoffman Estates, JL 60179 U.S.A.

,IIHIIII,,,,,,,,,,, , .......................

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Rotary Tillers

TRAINING

=Read the Owner's Manual carefully, Be thoroughly

familiar with the controls and the proper use of the

equipment,. Know how to stop the unit and disengage

the controls quickly.

= Never allow children to operate the equipment. Never'

a!iow adults to operate the equipment without proper

instruction..

= Keep the area of operation clear of al}persons, particu-

larly small children, and pets.

PREPARATION

o Thoroughly inspect the area where the equipment is to

be used and remove all foreign objects.

o Disengage all clutches and shift into neutral before

starting the engine (motor)°

°Do not operate the equipment without wearing ad-

equate outer garments_ Wear footwear that will im-

prove footing on slippery surfaces°

• Handle fuel with care; it is highly flammable.

- Use an approved fuel container.

° Never add fuel to a running engine or hot engine.

o Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

o Replace gasoline cap securely and clean up spilled

fuel before restarting..

o Use extension cords and receptacles as specified by

the manufacturer for a_{units with electric drive motors

or electric starting motors.

° Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by manufacturer).

OPERATION

o Do not put hands or feet near or under rotating parts.

o Exercise extreme caution when operating on or cross-

ing gravet drives, walks, or roads. Stay alert for hidden

hazards or traffic.. Do not carry passengers..

° After striking a foreign object, stop the engine (motor),

remove the wire from the spark plug, thoroughly in-

spect the tiller for any damage, and repair the damage

before restarting and operating the tiller.

o Exercise caution to avoid slipping or falling_

. if the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the cause°

Vibration is generaliy a warning of trouble..

o Stop the engine (mote 0 when leaving the operating

position..

o Take all possible precautions when leaving the ma-

chine unattended. Disengage the tines, shift into

neutral, and stop the engine_

o Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped

Disconnect the spark plug wire, and keep the wire

away from the plug to prevent accidental starting

Disconnect the cord on electric motors.

. Do not run the engine indoors; exhaust fumes are

dangerous.

° Never operate the ti!ler without proper guards, plates,

or other safety protective devices in place_

° Keep children and pets away.

o Do not overload the machine capacity by attempting to

tin too deep at too fast a rate.

° Never operate the machine at high speeds on slippery

surfaces. Look behind and use care when backing.

. Never allow bystanders near the unit..

. Use only attachments and accessories approved by

the manufacturer of the tiller (such as whee{ weights,

counterweights, cabs, and the like)..

° Never operate the tiller without good visibility or light..

o Be careful when tilling in hard ground. The tines may

catch in the ground and propel the tiller forward tf this

occurs, let go of the handlebars and do not restrain the

machine.

MAINTENANCE AND STORAGE

. Keep machine, attachments, and accessories in safe

working condition.

- Check shear pins, engine mounting bolts, and other

bolts at frequent intervals for proper tightness to be

sure the equipment is in safe working condition.

° Never store the machine with fuel in the fuel tank inside

a building where ignition sources ate present, such as

hot water and space heaters, clothes dryers, and the

like. Allow the engine to cool before storing in any

enclosure,.

, Always refer to the operator's guide instructions for

important details if the tiller is to be stored for an

extended period_

-IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF ATTRACTING ATTENTION TO {MPORTANT OR CRITICAL

INFORMATION IN THIS MANUAL,,

! _ cAUTIONI'Look for this symbolto point

_ out important safety precautions. It

means _Attention{ Become Alert{ Your

_ safety is involved,

IMPORTANT: USED TO ALERT YOU THAT THERE IS A

POSSIBILITY OF DAMAGING THIS EQUIPMENT

NOTE: Gives essential information that will aid you to better

understand, incorporate, or execute a particular set of instruc-

tions

CONGRATULATIONS on your purchase of a Sears Titler.

It has been designed, engineered and manufactured to

give you the best possible dependability and performance,

Should you experience any problems you cannot easily

remedy, please contact your nearest authorized Sears

Service Center/Department, They have competent, well-

trained technicians and the proper toots to service or repair

this unit.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your tiller properly.

Always observe the "SAFETY RULES",

MODEL

NUMBER 9't7.298353

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WILL BE

FOUND ON THE MODEL PLATE ATTACHED TO

THE RIGHT HAND ENGINE BRACKET.

YOU SHOULD RECORD BOTH SERIAL NUMBER

AND DATE OF PURCHASE AND KEEP IN A SAFE

PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

HORSEPOWER: 5.0 HP

DISPLACEMENT: 12_57cu. in.

GASOLINE CAPACITY: 3 Quarts

Unleaded Regular

elL (API-SG): SAE 30 (Above 320F)

(CAPACITY; 20 oz) SAE 5W-30 (Below 32°F)

SPARK PLUG : Champion

(GAP; .030") RJ19LM (STD361458)

, , . J

MAINTENANCE AGREEMENT

A Sears Maintenance Agreement is available on this prod-

uct. Contact your nearest Sears store for details.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules,

• Fo!lowa regular schedule in maintaining, caring for and

using your tiller.

• Follow the instructions under "Customer

Responsibilities" and "Storage" sections of this Owner's

Manual.

IMPORTANT:THIS UNIT IS EQUIPPED WITH AN INTERNAL COMBUSTION ENGINE AND SHOULD NOT BE USED ON

OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-COVERED OR GRASS COVERED LAND UNLESS THE

ENGINE'S EXHAUST SYSTEM iS EQUIPPED WITH A SPARK ARRESTER MEETING APPLICABLE LOCAL OR STATE

LAWS (IF ANY). IFA SPARK ARRESTER tS USED, IT SHOULD BE MAINTAINED IN EFFECTIVE WORKING ORDER BY

THE OPERATOR°

IN THE STATE OF CALIFORNIA THE ABOVE tS REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA PUBLIC

RESOURCES CODE). OTHER STATES MAY HAVE SIMILAR LAWS. FEDERAL LAWS APPLY ON FEDERAL LANDS.

SEE YOUR SEARS AUTHORIZED SERVICE CENTER/DEPARTMENT FOR SPARKARRESTER REFER TO THE REPAIR

PARTS SECTION OF THIS MANUAL FOR PART NUMBER.

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN TILLER

For one (1) year from date of purchase, when this Craftsman Til_er is maintained, lubricated, and tuned up according

to the operating and maintenance instructions in the owner's manual, Sears wilt repair free of charge any defect in

material or workmanship.

This Warranty does not cover:

, Expendable items which become worn during normal use, such as tines, spark plugs, air cleaners and beltSr

" Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to

maintain the equipment according to the instructions contained in the owner's manual.

° If this Craftsman Tiller is used for commercial or rental purposes, this Warranty applies for only thirty (30) days

from the date of purchase.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN TILLER TO THE NEAREST SEARS

SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS

PRODUCT IS IN USE IN THE UNITED STATES_

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state,

SEARS, ROEBUCK AND CO, D/8t7 WA, HOFFMAN ESTATES, IL 60179

SAFETY RULES ........................................................... 2

CUSTOMER RESPONSIBILITIES ..................... 3, 12-14

PRODUCT SPECIFICATIONS ...................................... 3

WARRANTY .................................................................. 3

ACCESSORIES ............................................................. 5

ASSEMBLY ................................................................ 6-7

OPERATION ............................................................ 8-11

MAINTENANCE SCH EDULE ...................................... 12

SERVICE & ADJUSTMENTS ................................. 14-17

STORAGE ................................................................... 18

TROUBLESHOOTING ................................................. !9

REPAIR PARTS-TILLER ....................................... 20-25

REPAIR PARTS-ENGINE ...................................... 26-30

SERVICE/PARTS ORDERING .................... Back Cover

iNDEX

Accessories ...............................................5

Adjustments:

Carburetor .................................. 17

Depth Stake ......................................9

Handle Height ................................14

Tines .......................................14-15

V-Belt .........................................................16

Wheels .................................................9

Air' Cleaner .............................................13

Belt, V-:

Belt Guard ....................................16

Repair Parts ...................................21

V-Belt Replacement ................... 16

Cooling System ....................................13

Controls:

Choke ...........................................................8

Throttle .....................................................8

Tines ...........................................................8

Cultivating ...................................................t 1

Customer Responsibilities:

Air Cleaner. ...................................t3

Cooling System ...............................13

Finish ..............................................14

Maintenance Schedule ............. 12

Muffler ...............................................14

Oil Change ......................................13

Spark Plug .............................................14

Transmission ..................................14

Depth Stake:

Adjustment ..................................... 9

Repair Parts ......................................22

Engine:

Air Cleaner .......................................t3

Cooling System ............................13

Fuel Type ...............................................10

Lubrication ......................................13

Oil Level ...............................................10

Engine (cont'd):

Oil Type ......................................10,13

Repair' Parts ................................. 26-30

Spark Plug .......................................14

Starting .....................................................10

Stopping ..............................................9

Storage .........................................18

Winter Operation ............................13

Fuel:

Filling Tank .......................................10

Storage ...............................................18

Type ......................................................10

Finish:

Maintenance .....................................14

Handle:

Height Adjustment .......................14

Repair Parts ......................................20

Lubrication:

Lubrication Chart .......................12

Engine ...................................................13

Muffler:

Maintenance ..............................................14

Spark Arrester ..................................3

Oil: Level ..........................................................10

Type ................................................10,13

Operation:

Cultivating ...........................................1t

Fill Fuel Tank ........................................10

Starting Engine ..............................10

Stopping Tines & Engine ...............9

Tilling ......................................................9

Tilling Hints ..................................11

Tine Operation ...............................g

Transporting Tiller ................... 10

Winter Operation ...........................13

Repair Parts

Tiller ...........................................20-25

Engine ....................................26-30

Rules for Safe Operation .......................2

Sen,ice & Adjustments:

Carburetor ........................................17

Handle Height ................................14

Tines .........................................14-15

V-Belt ............................................................16

Wheels .......................................................9

Service:

Repair Parts ............................... 20-30

Service Record .................................12

Spark Plug:

Gap .......................................................3

Maintenance .......................................t4

Storage:

Fuel System .....................................18

Ti!ler .................................................... 1 8

Tilling ...........................................................9,11

Tines:

Arrangement ...........................t4-15

Operation ...........................................9

Repair Parts ................................23

Replacement .................................15

Transmission:

Maintenance .......................................14

Repair Parts ....................................24

Troubleshooting .....................................19

Transporting ............................................10

Warranty ..........................................................3

Wheels:

Adjustments .........................................9

Repair Parts .....................................22

ACCESSO

These accessories were available when the tiller was purchased. They are also available at most Sears Retail outlets

and Service Centers. Most Sears Stores can order repair parts for you when you provide the model number of your

tiller.

ENGINE

SPARKPLUG

._-- LL

.....MUFFLER "AIRFILTER STABILIZER""" '

GAS CAN ENGINE OIL

TILLER MAINTENANCE

CLEVIS PIN ...... HAIRPIN CLIP

ii,q , iHIIII ll,jl 2

BEEr TINES

,,, ._ ,

€

BLY

Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To

ensure safe and proper operation of your tiller atl parts and hardware you assemble must be tightened securely, Use the

correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard

wrench sizes are listed°

(1) Utility knife

(1) Screwdriver

(t) Pair of pliers

(2) 1/2" wrenches

OPERATOR'S POSITION (See Fig. 1)

When right or left hand is mentioned in this manual, it

means when you are in the operating position (standing

behind tiller' handles),

LEFT

FRONT

[_ IGHT

OPERATOR'S

POSITION

CONTENTS OF HARDWARE PACK

FIGo I

................. i

(1) Owner's Manual (1) Plastic Cable Clip

(2) Flange Locknuts 5/16-18 UNC

D!ijiililiait!t!s!a! ! !

(2) Hex Bolts 5/16-18 x 1-1/4

(2) Hex Nuts 5/16-18

,H i I IIH, I, IHmIH

(2) Lock Washers 5/16

UNPACK CARTON & INSTALL HANDLE

(See Fig. 2)

CAUTION: Be careful of exposed

staples when handling or disposing of

cartontng material.

IMPORTANT: WHEN UNPACKING AND ASSEMBLING

TILLER, BE CAREFUL NOT TO STRETCH OR KINK

CABLE(S),

•Cut cable ties securing handle column°

•Slowly lift handle column up and slip over handie

mount_

•Remove packing from carton,

• Secure handle column to handle mount using two (2)

carriage bolts and two (2) flange locknuts. Tighten both

flange ]ocknuts securely,

• Insert piastic cable clip into hole in handIe column,

•Route tine control cable through plastic cable clip on

handle column,

, Remove packing material from handle assembly.

• Cut cable ties securing tiller to skid.

°Cut away carton and remove tiller from skid by pulling

backwards.

TINECONTROL

CABLE

HANDLE

MOUNT

HANDLE

COLUMN

BOLT

FLANGE

LOCKNUT CABLE

Cl.IP

INSTALL DEPTH STAKE ASSEMBLY

(See Fig. 3)

. Insert stake support between engine bracket halves

with stake spring down°

NOTE: It may be necessary to loosen nut "A".

• Bolt stake support to engine brackets with bolts, lock

washers and nuts. Tighten securely. Also tighten nut

"A" if it was necessary to loosen.

. Depth stake must move freely. If it does not, loosen

support bolto

HANDLE HEIGHT

•Handle height may be adjusted to better suit operator°

(See "HANDLE HEIGHT" in the Service and Adjust-

ments section of this manual)°

TILLING WIDTH

• Tilling width may be adjusted to better handle your

tilling conditions (See "TiNE ARRANGEMENT" in the

Service and Adjustments section of this manual).

TINE OPERATION

• Check tine operationbefore first use. (See "TtNE

OPERATION CHECK inthe Service and Adjustments

section of this manual)_

ENGINE BRACKET

DEPTH

STAKE

HEX BOLTS,

LOCK

WASHERS_

AND HEXNUTS

SUPPORT

BOLT

FIG. 3

FIG. 2

......................... ii ii illlll iiilll i ii ,i ,,llll,!,l

OPERATION

................ ii i HIIIII

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments, Save

this manua_ for future reference,

TINE CONTROL

5CONTROL

DEPTH STAKE

tROTTLE

CONTROL

SHIELD

RECOIL

STARTER

HANDLE

FIG. 4

MEETS ANSl SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards institute,

TINE CONTROL - Engages tines,

CHOKE CONTROL - Used when starting a cold engine

THROTTLE CONTROL- Controls engine speed_

DEPTH STAKE -Controls forward speed and the depth at

which the tiller will dig,

RECOIL STARTER HANDLE - Used to start the engine.

fi,l,lll, i iii ii,, i i,iiii .....................................

OPERATION

i i ,, , ...... ,i,,m,m, i ..............

The operation of any tiller can result in foreign objects thrown into the eyes, which can

result in severe eye damage, Always wear safety glasses or eye shields before starting

your tiller and while tilling. We recommend a wide vision safety mask for over the spec-

tacles or standard safety glasses.

HOW TO USE YOUR TILLER

STOPPING (See Fig. 5)

TINES

" Release tine control to stop movement.

ENGINE

,Move throttle control to "STOP" position.

• Never use choke to stop engine°

TINE CONTROL

"OFF" (UP) POSITION

TINE CONTROL

"ON" (DOWN) POSITION

CHOKE _THRO't'FLE

CONTROL,_

FIG. 5

TINE OPERATION (See Fig, 5)

Start engine and move throttle control to desired speed,

• Squeeze tine control to handle,

TILLING

The speed and depth of tilling is regulated by the position

of the depth stake and wheel height.

The depth stake should always be below the wheels for

digging. It serves as a brake to slow the titler's forward

motion to enable the tines to penetrate the ground. Also,

the more the depth stake is lowered into the ground the

deeper the tines wiII dig.

DEPTH STAKE (See Fig, 6)

Adjust depth stake by removing the hairpin clip and clevis

pin. Change depth stake to desired position. Replace the

clevis pin and hairpin clip.

• For normal tilling, set depth stake at the second or third

hole from the top.

WHEELS (See Fig, 6)

Adjust wheels by removing the hairpin clip and clevis pin.

Change wheel position. Replace the hairpin clip and clevis

pm.

• For normal tilling, set wheels at the second or third hole

from the top.

HAIRPIN CLIP

AND CLEVIS PIN

DEPTH

STAKE

SPRING HAIRPIN CLIP

AND CLEVfS PIN

_WHEEL

FIG, 6

i1.11 .i.i ...i.=1.....i. . i i..... ' f i i i ..... i..i ..H , i i.i .I.I.........HI

OP RATnO

miH'HHH ' I'

TRANSPORTING YOUR TILLER

, ,111,1,,1111,1

CAUTION: Before lifting or transport-

ing, allow tiller engine and muffler to

cool. Disconnect sparkplugwire. Drain

gasoline from fuel tank.

i ,i,,, Hll

AROUND THE YARD

°Tip depth stake forward until it is held by the stake

spring

• Push tiller handles down, raising tines off the ground°

• Push or pull tiller to desired location.

AROUND TOWN

o Disconnect spark plug wire.

= Drain fuel tank_

= Transport in upright position to prevent oil leakage

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW

DIRT TO ENTER THE ENGINE WHEN CHECKING OR

ADDING OIL OR FUEL USE CLEANOILANDFUELAND

STORE IN APPROVED, CLEAN, COVERED

CONTAINERS USE CLEAN FILL FUNNELS

FILL ENGINE WiTH OiL (See Fig. 7)

° With engine level, remove engine oil filler plug.

o Fill engine with oif to point of overflowing. For approxi-

mate capacity see "PRODUCT SPECIFtCATIONS" on

page 3 of this manual.

°Tilt tiller back on its wheels and then re-leveL

o Check oil level. Refill to point of overflowing if neces-

sary_ Replace oil filler plug.

oFor cold weather operation you should change oil for

easier starting (See "OIL VISCOSITY CHART" in the

Customer Responsibilities section of this manual)..

• To change engine oil, see the Customer Responsibili=

ties section of this manual.

OIL

FILLER

PLUG

FIG. 7

ADD GASOLINE

o Fill fuel tank. Use fresh, clean, regular unleaded

gasoline.. (Use of leaded gasoline wiil increase carbon

and lead oxide deposits and reduce valve life_

IMPORTANT: WHEN OPERATING iN TEMPERATURES

BELOW 32°F, USE FRESH, CLEAN, WINTER GRADE

GASOLINE TO HELP iNSURE GOOD COLD WEATHER

STARTING

WARNING: Experience indicates that alcohol blended

fuels (called gasohol or' using ethanol or methanol) cart

attract moisture which leads to separation and formation of

acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before stor-

age of 30 days or longer. Drain the gas tank, start the

engine and Iet it run until the fuel lines and carburetor are

empty_ Use fresh fuel next season. See the Storage

section of this manual for additional information. Never use

engine or carburetor cleaner products in the fuel tank or

)ermanent damage may occur..

i i HI_,H ' 'H,

CAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to

allow for fuel expansion. If gasoline is

accidentally spilled, move machine

away from area of spill. Avoid creating

any source of ignition until gasoline

vapors have disappeared.

Do not overfill Wipe off any spilled oil

or fuel. Do not store, spill or use gaso-

line near an open flame°

TO START ENGINE (See Fig. 8)

"_ CAUTION: Keep the tine control in

OFF position when starting engine,

°Make sure spark plug wire is properly connected.

o Place throttle control in "FAST" position.

° To start acold engine, piace choke control in"CHOKE"

position. A warm engine requires less choking to starL

o Grasp starter handle with one hand and grasp the tiller

with other hand. Pull rope out slowly until engine

reaches start of compression cycle (rope will pull

slightly harder at this point).

Pull starter handle quickly. Do not let starter handle

snap back against starter.

o When engine starts, slowly move choke control tO

"RUN" position as engine warms up.

• Move throttle control to desired running position..

o Allow engine to warm up for a few minutes before

engaging tines

NOTE: if at a high altitude (3000 feet) or in cold tempera-

tures (below 32°F), the carburetor fuel mixture may need to

be ad'iusted for best engine performance. See "TO AD-

JUST CARBURETOR" in the Service and Adjustments

section of this manual.

k-i_l,-lu..ul.-,.u, , , i i ii

OPERATION

i ................................

SPARK

PLUG

CONTROL

)]rTLE

CONTROL

RECOIL STARTER

HANDLE

FIGo 8

BREAKING IN YOUR TILLER

Break.in your belt(s), pulleys and tine control before you

actually begin tilling.

•Start engine, tip tines off ,]round by pressing handles

down and engage tine control to start tine rotation

AIIow tines to rotate for five minutes.

•Check tine operation and adjust if necessary. See

"TINE OPERATION CHECK" in the Service and Ad-

justments section of this manual

TILLING HINTS

i .....................

CAUTION: Until you are accustomed to

handling your tiller, start actual field

use with throttle in "SLOW" position.

To help tiller move forward, liftup the handles slightly (thus

lifting depth stake out of ground). To slow down the tiller,

press down on handles

if you are straining or tiller is shaking, the wheels and depth

stake are not set properly in the soll being tille& The proper

setting of the wheels and depth stake is through trial and

error and depends upon the soil condition. (The harder or

wetter the ground, the slower the engine and tine speed

needed° Under these poor conditions, at fast speed the tiller

will run and jump over the ground)°

A properly adjusted tiller will dig with little effort from the

operator.

, Tilling is digging into, turning over, and breaking up

packed soil before planting, Loose, unpacked soil

helps root growth. Best tilling depth is 4" to 6". A tiller

will also clear the soil of unwanted vegetation. The

decomposition of this vegetabJe matter enriches the

soil Depending on the climate (rainfall and wind), it

may be advisable to till the soil at the end of the growing

season to further condition the soil.

,Soil conditions are important for proper tilling. Tines will

not readily penetrate dry, hard soil which may contrib-

ute to excessive bounce and difficult handling of your

tiller. Hard soil should be moistened before tilling;

however, extremely wet soil will "bali-up" or clump

during tiiling_Wait until the soil is less wet in order to

achieve the best results° When tilling inthe fall remove

vines and ong grass to prevent them from wrapping

around the tine shaft and slowing your tilling operation.

You will find tilling much easier if you leave a row

untilled between passes. Then go back over the entire

area _t right angles (See Fig. 9). There are two reasons

for doing thi& First, wide turns are much easier to

negotiate than aboutffaces Second, the tiIler won't be

pulling itself, and you, toward the row next to it

Set depth stake and wheel height for shallow tilling

when working extremely hard soil or sod Then work

across the first cuts at normal depth.

FIG, 9

CULTIVATING

Cultivating is destroying the weeds between rows to pre-

vent them from robbing nourishment and moisture from

the plants° At the same time, breaking up the upper layer

of soil crust will help retain moisture in the soil. Best

digging depth is 1" to 3'L

• You will probably not need to use the depth stake.

Begin by tipping the depth stake forward until it is held

by the stake spring.

• Cultivate up and down the rows at a speed which will

allow tines to uproot weeds and leave the ground in

rough condition, promoting no further growth of weeds

and grass (See Fig. 10).

S-".

FIG. 10

l - Change more often when operating under a heavy load or in hlgh ambient temperatures

2 - Service more often when operating in dirty or dusty conditions

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover items that have

been subjected to operator abuse or negligence_ To

receive full value from the warranty, operator must main-

tain tiller as instructed in this manual

Some adjustments wilt need to be made periodically to

properly maintair_ your tiller,

All adjustments in the Service and Adjustments section of

this manual should be checked at least once each

season,

• Once a year you should replace the spark plug, clean

or replace air filter, and check tines and belt for wear,

A new spark plug and clean air filter assure proper air-

fuel mixture and help your engine run better and last

longer,

BEFORE EACH USE

• Check engine oil level

• Check tine operation.

• Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See "LUBRICATION CHART").

LUBRICATION CHART

'_' ENGINE /_

'_IDLER

ARM

_'SAE30 OR10W30 MOTOROIL

'_ REFERTO CUSTOMER RESPONSIBILITIES"ENGINE" SECTION.

CUSTO RESPONSmBBL THES

s'conn'ect spark plug wire before perfo'rming any"rna'intenar=ce'ie×cept carbur'eto'r ad';ustment)to prevent t

cidentat starting of engine.

event fires! Keepthe engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping

it for maintenance. Clean muffler area of all grass, dirt, and debriso

Do,not touc.h hot,.m.uffler or cylinder fins as conta,ct,maY,,,c.a.u.seburns. _ ........................................................ J

ENGINE AIR CLEANER (See Fig. 13)

LUBRICATION

Use only high quality detergent oil rated with API service

classification SG. Select the oil's SAE viscosity grade

accordfng to your expected temperature.

SAE VISCOSITY GRADES

_'F -20" O" ;30" 32* 40" 60 _ 80 `= 100 _

°c -_o" .2'o_ ._,, _" ,oo 20° 3o'. _o°

TEMPERATURE RANGE ANTICIPA ;ED BEFORE NEXT OIL CHANGE ._.j

FIG. 11

NOTE: Although muItFviscosity oils (5W-30, 10W-30, etc.)

improve starting in cold weather, these multFviscosity oils

will result in increased oil consumption when used above

32°F (0°C). Check your engine oil level more frequently to

avoid possible engine damage from running low on oil,

Change the oil after the first two hours of operation and

every 25 hours thereafter or at least once a year if the tiller

is not used for 25 hours in one year,

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Add SAE

30 motor oil or equivalent., Tighten oil filler plug securely

each time you check the oil level,

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expectec! before oil change

All oil must meet API service classification SGo

•Be sure tiller is on level surface.

o Oil will drain more freely when warm..

° Catch oil in a suitable container.

= Remove drain ptug.

" Tip tiller forward to drain oil

,, After oil has drained completely, replace oil drain pfug

and tighten securelyo

•Remove oil filler plug. Be careful not to allow dirt to

enter the engine.

oRefilt engine with oit. See "CHECK ENGINE OIL

LEVEL" in the Operation section of this manual,

Service air cleaner cartridge every twenty-five hours, more

often if engine is used in very dusty conditions.

•Loosen air cleaner screws, one on each side of cover.

.Remove air cleaner cover

°Carefully remove air cleaner cartridge.. Be careful Do

not allow dirt or debris to fali into carburetor..

. Clean by tapping gentry on a flat surface.

.If very dirty, replace or wash ina nonsudsing detergent

andwarm watersoIution Rinse thoroughly with water

flowing from mesh side until water is clear. Allow

cartridge to stand and air dry thoroughly before using.

,' Clean and replace cover. Tighten screws securely.

i,,,n,,i, i1,,i,,i, n,,,,,,i

CAUTION: Petroleum solvents, such

as kerosene, are not to be used to clean

cartridge° They may cause deteriora-

tion of the cartridge. Do not oil car-

tridge. Do not use pressurized air to

clean or dry cartridge.

COVER

AIR

CLEANER

CARTRIDGE

FIG. 13

COOLING SYSTEM (See Fig. 14)

Your engine is air cooled.. For proper engine performance

and long life keep your engine clean.

o Cleanair screen frequently using a stiff-bristled brush

•Remove blower housing and clean as necessary.

° Keep cylinder fins free of dirt and chaff.

OIL

DRAIN

PLUG

OIL FILLER

PLUG

LEVEL

CYLINDER FINS

MUFFLER__

BLOWER

_ING

SCREEN

FIG. 12 13 FIG. 14

MUFFLER

Do not operate tiller without muffler_ Do not tamper with

exhaust system.. Damaged muffler's or spark arresters

could create a fire hazard. Inspect periodically and replace

if necessary. If your engine is equipped with a spark

arrester screen assembly, remove every 50 hours for

cleaning and inspection, Replace if damaged

SPARK PLUG

Replace spar k plugs at the beginning of each tilling season

or after every 50 hours of use, whichever comes first. Spar k

plug type and gap setting is shown in "PRODUCT SPECI-

FICATIONS" on page 3 of this manual

TRANSMISSION

You r transmission is sealed and will only require lubrication

if it is serviced,,

CLEANING

° Clean engine, wheels, finish, etcoof all foreign rnatter_

o Keep finished surfaces and wheels free of all gasoline,

oil, etc..

Protect painted surfaces with automotive type wax,.

We do not recommend using a garden hose to clean your

unit unless the muffler, air filter and carburetor are covered

to keep water out. Water inengine can result in ashortened

engine life.

i ...... III'I'IIIHHI'IH ¸ '1 ............... I"1' " '1'1"'1 .................... I'1""'1

SERVtCE ADJUSTMENTS

i i ,11,, , ,i,,,i,1,, i ...... i i,i1,1,111,11, ,i

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into

contact with plug.

,=, ,,i,, HH",H,

TILLER

TO ADJUST HANDLE HEIGHT (See Fig, 15)

Factory assembly has provided lowest handle heighL Se-

lect handle height best suited for your tilling conditions,

Handle height will be different when tiller digs into soil

• If a higher handle height is desired, loosen the four nuts

secunng handle panel to engine brackets,.

o Slide handle panel to desired location_

o Tighten the four nuts securely

TINE ARRANGEMENT

Your outer tines can be assembled inseveral different ways

to suit your tilling or cultivating needs,.

ICAUTION: Tines are sharp. Wear t

gloves or other protection when han-

dling tines_....................... !

NORMAL TILLING -24 INCH PATH (See Fig. 16)

• Assemble holes "A" in tine hubs to holes "B" in tine

shaft,

ENGINE

BRACKETS

HANDLE

PANEL

NUTS (ALSO 2

ON LEFT SIDE

OF TILLER)

_,"_' CLEVIS OUTER

PiN TIN_

HAIRPIN CLIP INNER TfNE

FIG. 16

FIG, 15

,, i

SERVICE AN

i1,,,11,,,,,i,, , ,, 11,,i...... ii1,1,

MID-WIDTH TILLING -22 INCH PATH (See Fig° 17)

oAssemble ho_es "A" in tine hubs to holes "C" in tine

shaft.

FIG, 17

NARROW TILLING!CULTIVATING - 12-3t4 INCH PATH

(See Fig. 18)

o Remove outer tines

iNNER TINES ONLY

FIG. 18

NOTE: When reassembling outer tines, be sure right tine

assembly (marked "R") and [eft tine assembly (marked "L")

are mounted to correct side of tine shaft.

TINE OPERATION CHECK (See Fig. 19)

U ...................!

WARNING: Disconnect spark plug wire

from spark plu9 to prevent starting

while checking tree operation.

.... i,,,,,i,,,i .... iiii ,,

For proper tine operation, tine control lever must be against

control body and all slack removed from inner wire of

control cable when control is in the "OFF' (up) position,

If !ever and cabte are loose, loosen cable clip at lower end

of cable_ Pull up on cable to remove slack, without

extending spring on end of cabie, and retighten cable clip_

FINAL CHECK "OFF" POSITION

o With tine control "OFF" (up), push down on handle to

raise tines off the ground

•Slowly pull recoil starter handle while observing tines.

Tines should not rotate°

oIf tines rotate, inner wire of control cable is too tight

which is extending lower spring and engaging tines.

Loosen cabte clip and push down on cable only enough

to relieve spring tension. Tighten cable clip.

.Recheck in "OFF" position and adjust if necessary

i,,,i, iiii i i

ADJUSTMENTS

i,, i1,,,,,,,,i ,, i,,,

FINAL CHECK "ON" POSITION

With tine control"ON" (held down to handle) push down

on handle to raise tines off the ground

o Slowly pull recoil starter handle while observing tinesr

Tines should rotate forward.

= if tines do not rotate, inner wire of control cable is too

loose. Loosen cable clip and pu!l cable up to remove

slack and retighten clip

oRecheck in "ON" position and adjust if necessary,

NOTE: If "ON" position check required adjustment, re-

check "OFF" position adjustment to insure tines do not

rotate when control is "OFF" (up),

TINE CONTROL -_'

"ON" POSITION

CLIP TINE

CONTROL

CABLE

FIG_ 19

i, '!ll II I II1' "1 "1' IIIII1'1'1'11 ' ' ' I1',= "1 ....... I'

SERVmCE AND ADJUSTMENTS

,i, ,, ,,,,,11111 i,i,i, i................... i,i............. i

TO REPLACE V-BELT (See Fig. 20)

Replace V-belt if it has stretched considerably or if it shows

cracks or frayed edges_

Belt guard must be removed to service belt.. See "TO

REMOVE BELT GUARD" in this section of manual

BELT REMOVAL

. Remove V-belt from transmission pulley first and then

from engine pulley_

BELT REPLACEMENT

oinstallnewV-belt to engine pultey firstthen to transmis-

sion pulley_ Be sure belt is positioned on inside groove

of both pulleys, inside all belt guides and rests on idler

pulley.

CHECK TINE OPERATION

o See "I'INE OPERATION CHECK" in this section of

manual.

REPLACE BELT GUARD

BELT

GUIDE _

ENG,HEPO"EY /

PULLEY

TRANSMISSION

PULLEY

FIG, 20

TO REMOVE BELT GUARD (See Fig. 21)

° Remove cap nut and washer from side of belt guard

• Loosen (do not remove) tine shield nut on underside of

tine shield and cap nut on top of belt guard.

Pull belt guard out and away from uniL

= Replace belt guard by reversing above procedure Be

sure slot in bottom of belt guard is under head of tine

shield bolt and all nuts are tightened securely

BELT GUARD CAP NUT CAP NUT

AND WASHER

SHIELD

NUT

T'tNE

SHIELD

F|Go21

ENGUNE

TO ADJUST CARBURETOR (See Fig. 22)

The carburetor has a high speed fixed jet and has been

preset at the factory and adjustment shoutd not be neces-

sary, However, minor adjustments may be required to

compensate for differences in fuel, temperature, altitude or

load. If the carburetor does need adjustment, proceed as

follows.

In general, turning the idle needle valve in (clockwise)

decreases the supply of fuel to the engine giving a leaner

fuel/air mixture. Turning the needle valve out (counter-

clockwise) increases the supply of fuel to the engine giving

a richer fuel!air mixture.

IMPORTANT: DAMAGE TO THE NEEDLES AND THE

SEATS IN CARBURETOR MAY RESULT IF SCREWS

ARE TURNED IN TOO TIGHT,

PRELIMINARY SETTING

• Air cleaner assembly must be assembled to the carbu-

retor when making carburetor adjustments..

• With engine off, turn idle needle valve in (clockwise)

closing it finger tight and then turn valve out (counter-

clockwise) 1-1/2 turns_

FINAL SETTING

• Start engine and allow to warm for five minutes. Make

final adjustments with engine running at idle and fine

control lever in "OFF" position.

, With throttle control in "SLOW" position, turn idle

needle valve in (clockwise) until engine begins to die

then turn out (counterclockwise) until engine runs

rough. Turn valve to a point midway between those

two positions..

IDLE RPM ADJUSTMENT

• To adjust idle RPM, rotate throttle linkage counter-

clockwise and hold against stop whNe adjusting idle

speed ad usting screw to obtain 1750 RPM Release

thrott e nkage.

ACCELERATION TEST

o Move throttle control lever from "SLOW" to "FAST"

position. If engine hesitates or dies, turn idle needie

valve out (counterclockwise) 1/8 turn. Repeat test and

continue to adjust, if necessary, until engine acceler_

ares smoothly.

High speed stop is factory adjusted. Do not adjust or

damage may result.

IMPORTANT; NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED OVERSPEEDINGTHEENG1NEABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS° IFYOU THtNKTHE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS PROPER EQUIPMENTAND

EXPERIENCE TO MAKE ANY NECESSARY

ADJUSTMENTS.

THROTTLE LINKAGE THROTTLE STOP

IDLE SPEED

ADJUSTING SCREW IDLE NEEDLE VALVE

FIG, 22

Immediately prepare your tiller for storage at the end of the

season or if the unit will not be used for 30 days or more.

CAUTION: Never store the tiller with

gasoline in the tank inside a building

where fumes may reach an open flame

or spark. Allow the engine to coot

before storing in any enclosure=

TILLER

o Clean entire tiller (See "CLEANING" in the Customer

Responsibilities section of this manual),,

o Inspect and replace belts, if necessary (See belt re-

placement instructionsinthe Service and Adjustments

section of this manual),,

.Lubricate as shown in the Customer' Responsibilities

section of this manual,

° Be sure that all nuts, bolts and screws are securely

fastened° Inspect moving parts for damage, breakage

and wear. Replace if necessary.

°Touch up all rusted or chipped paint surfaces; sand

lightly before painting,

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM

DEPOSITS FROM FORMING iN ESSENTIAL FUEL

SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL

FILTER, FUEL HOSE, OR TANK DURING STORAGE

ALSO, EXPERIENCE INDICATES THAT ALCOHOL

BLENDED FUELS (CALLED GASOHOL OR USING

ETHANOL OR METHANOL) CAN ATTRACT MOISTURE

WHICH LEADS TO SEPARATION AND FORMATION OF

ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE

THE FUEL SYSTEM OF AN ENGINE WHILE tN STORAGE

,Drain the fuel tank.

o Start the engine and let it run until the fuel lines and

carburetor are empty..

• Never use engine or car buretor cleaner products in the

fuel tank or permanent damage may occur.

, Use fresh fuel next season..

NOTE: Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during stor-

age. Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stabilizer

container. Run engine at least 10 minutes after adding

stabilizer to allow the stabilizer to reach the carburetor. Do

not drain the gas tan k and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil

(See"ENGINE" inthe Customer Responsibilities section of

this manual).

CYLINDERS

•Remove spark plug

o Pour 1 ounce (29 ml) of oil through spar k plug hole into

cylinder.

° Pull starter handle slowly several times to distribute oilo

o Replace with new spark plug

OTHER

°Do not store gasoline from one season to another.

oReplace your gasoline can if your carl starts to rusL

Rust and/or dirt in your gasoline will cause problems°

o If possible, store your unit indoors and cover it to give

protection from dust and dirt°

oCover your unit with a suitable protective cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe which allows condensation to for m and

will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE

AND EXHAUST AREAS ARE STILL WARM,

TROUBLESHOOTgNG POHNTS

[fill ,l I111 I I ,

CAUSE CORRECTION

PROBLEM

Will not start

Hard to start

t., Out of fuel

2, Engine not "CHOKED" properly

3 Engine flooded

4 Dirty air cleaner,

5. Water tn fuel.

6 Clogged fueltank.

7Loose sparkplug wire

8- Bad spark plug or improper gap,

9 Carburetor out of adjustment

1. Throttle control not set properly

2, Dirty alr cleaner.

3. Bad spark plug or Improper gap

4. Stale or dirty fuel,

5 Loose sparkptug wire

6. Carburetor out of adjustment,

1. Ftil flJeltank.

2. See "TO START ENGINE" In the Operation section.

3Wait several minutes before attempting to start,

4Clean or replace atrcleanercartrldge,

5. Dratn fuel tank and carburetor, and refill tank with fresh

gasoline

6. Remove fuel tank and clean

7. Make sure spark plug wire Is seated properly on plug.

8. Replace spark plug or adjust gap

9_ Make necessary adjustments.

1. Place throttle control In "FAST" position

2. Clean or replace air cleaner cartridge.

3. Rap{ace spark plug or adjust gap.

4. Drain fuel tank and raffle with fresh gasoline,

5 Make sure spark plug wtre is sealed properly on plug,

6, Make necessary adjustments,

Lossofpower t Engine is overloaded,

2, Dirty air cleaner

3, Low oil level/dirty oil,,

4 Faulty spark plug.

5, Oil In fuel.

6 Stale or dirty fuel,

7,, Water In fuel

8Clogged fuel tank,

9. Spark plug wire loose.

10 Dirty engine air screen

1 Set depth stake and wheels for shallower filling.

2Clean or replace air cleaner cartridge,

3r Check elllevel/change oil

4r Clean and regap or change spark plug

5 Drain and clean fuel tank and refill, and clean carburetor

6. Drain fuel tank and refill with fresh gasollnso

7. Drain fuel tank and carburetor, and refill tank with fresh

gasoline.

8. Remove fuel tank and clean

9, Connect and tighten spark plug wire

tO Cfean engine air screen,

Engine overheats

Excessive bounce/

difficult handling

Soil baIle up or clumps

1Dlrtylclogged muffler 11

12_ Carburetor out of adjustment. 12,

13 Poor compression 13

1 Low oil leveVdlrty olf

2 D]rtyenglne air screen

3, Dirty engine

4, Partially plugged muftler,,

5 Improper carburetor adjustment

1 Ground too dryand hard

2 Wheels and depth stake incorrectly adjusted

Ground too wet,

C}ea-n/replace muffler,

Make necessary adjustments

Contact an authorized service center/departmenL

1, Check oll lever/change oll

2, Clean engine air screen,

3Clean cylinder fins, air screen, muffler area,

4, Remove and clean muffler

5. Adjust carburetor to richer position.

1, Moisten ground or watt for more favorable soil

conditions

2 Adjust wheels and depth stake,

1 Walt for more favorable soil conditions.

Engine runs but tiller

won't move

Engine runs but labors

when tilling

1, Tine control is not engaged,

2 V*belt not correctly adjusted

3 V-beltls off pulley(s),

f Tilling too deep.

2 ThroWs control not properly adjusted,

3. Carburetor out of adIustment

1 Engage tinecontroL,

2. lnspec'Jadjust V-belt.

3 Inspect V-belt

t Set depth stake for shallower tilling,

2, Check throttle controlsettlng

3- Make necessary adjustments.

REPAIR PARTS

5 HP

HANDLE ASSEMBLY

24" TILLER - -MODEL NUMBER 917.298353

KEY

NO.

PART

NO.

STD533125

137118

110512X

1t0632X

3066J

2635J

12000027

DESCRIPTION

* Bolt, Carriage

5/16-18 UNC x 2-318 Gr, 5

Panel, Control

Assembly, Handle Column

Grip, Handle

Cable, Tine Control

Lever, Control, Tine

Ring, Clip

KEY PART

NO. NO.

8 23200405

9 73970500

10 t2t145X

11 110514X

12 98000129

13 STD533107

DESCRIPTION

Screw, Set

Locknut, Flange 5/16-18 UNC

Clip, Cable

Assembly, Panel and Tube

Nut, Flange

* Bolt, Carriage 5/16-I8 x 3/4

*STANDARD HARDWARE--PURCHASE LOCALLY

NOTE: All component dimensions given in UoS, inches,

1inch = 25,4 mm

REPAIR PARTS

5 HP 24" TILLER - - MODEL NUMBER 917.298353

BELT GUARD AND PULLEY ASSEMBLY

KEY

NO.

PART

NO.

121313X

9484R

86777

74770812

DESCRIPTION

Bracket, Belt Guard

Clip, Cable

Screw, Hex, Washer Hd,, Slotted,

Thd. Cutting #10-24 x 1/2 Type D

Bolt, Hex 1/2-20 x 3/4

STD532505 * Bolt, Carriage 1/4-20 x 1/2

121463X Keeper, Belt

104213X Nut, Cap 1/4- 20

STD551025 * Washer 9/32 x 5/8 x 16 Ga,

131158X417

72140405

9180R

23230506

2649M

9175R

110528X

Guard, Belt

Bolt, Carriage 1/4-20 x 5/8

V-Belt

* Screw, Set, Socket, Headless

Key, Square

Pulley, Transmission

Bolt, Belt Guard

KEY PART DESCRIPTION

NO, NO.

t6 12000036 Ring, Klip

17 STD541237 * Nut, Hex, Jam 3/8-!6

18 9t78R Pulley, Idler

19 674A30 Arm, Idler

20 STD523712 * Bolt, Hex 3/8-16 x 1-1/4

21 106968X Shaft, IdlerArm

22 73350500 Nut, Hex, Jam 5/16-18

23 STD541025 *Nut, Hex 1/4-20

24 STD551125 *Washer, Lock 1/4

25 109227X Pad, Idler

26 130812 Pulley, Engine

*STANDARD HARDWARE-- PURCHASE LOCALLY

NOTE: All component dimensions given in U.S. inches.

1 inch = 25.4 mm

REPAHR PARTS

5 HP 24" TILLER - - MODEL NUMBER 917.298353

WHEEL AND DEPTH STAKE ASSEMBLY

17 19 20

2 3

2O 19 18

KEY

NO.

PART

NO.

9194R

74760520

STD523107

STD54t031

STD551131

STD541537

4921H

1952J

122233X

326J

STD623715

DESCRIPTION

Pin, Clevis

Bolt, Hex 5/16-18x 1-1/4

* Bolt, Hex 5/16-t8 x 3/4

*Nut, Hex 5/!6-18

* Washer, Lock 5/16

* Locknut 3/8-24

Clip, Hairpin

Support, Depth Stake, Roll.

Stake, Depth

Pin, Clevis

* Bolt, Hex 3/8-24 x 1-1/2 Gr° 5

KEY PART

NO. NO.

12 74760524

13 195tj

14 120958X

15 5388J

t6 121117X

17 t27832

18 STD551037

19 9190R

20 STD541437

21 74760516

DESCRIPTION

Bolt, Hex 5/16-18 xt-1/2 Gr, 2

Support, Depth Stake, L.H.

Washer

Spring, Stake

Bolt, Shoulder

Wheel

* Washer 13/32 x 13/16 x 11 Ga.

Bracket, Wheel

* Locknut, Crown 318-16

Bolt, Hex 5/16-18 x 1

*STANDARD HARDWARE-- PURCHASE LOCALLY

NOTE: All component dimensions given in U.So inches.

1 inch = 25_4 mm

REPAKR PARTS

5 HP

TINE ,_SSEIVIB LY

24" TILLER - - MODEL NUMBER 917.298353

KEY

NO.

PART

NO.

674A66

3146R

674A64

DESCRIPTION

Tine, Outer, R.H.

Clip, Hairpin

Tine, Inner, RH.

KEY

NO.

PART

NO.

674A63

674A65

4929H

DESCRIPTION

Tine, Inner, LH

Tine, Outer, L.H.

Pin, Clevis

REPAIR PARTS

5 HP

TRANSMISSION

24" TILLER - - MODEL NUMBER 917.298353

KEY PART

NO. NO.

t 74760524

2 STD623732

3STD551037

4 STD551137

5 STD541537

6 9056R417

7 1949J

8 110519X

9 STD551131

10 STD541031

!1 74760544

12 9173R

DESCRIPTION

Bolt, Hex 5/16-18 x t-1/2 Gr+2

*Bolt, Hex 3/8-24 x 3-1/4 Gr. 5

*Washer 13/32 x 13/16 x 1!

* Washer', Lock 3/8

Locknut 3/8-24

Shield, Tine

Bracket, Engine, R.H.

Bracket, Engine, L_H.

"Washer, Lock 5/10

*Nut, Hex 5/16+18

Bolt, Hex 5/16o18 x 2-3/4

Spacer, Split

12 8

KEY PART

NO. NO. DESCRIPTION

13 126669X

14 STD541431

15 19091412

16 19092016

17 STD551125

18 74610412

19 137263

Transmission

* Nut, Kegs 5/16-18 UNC

Washer 9/32 x 7/8 x t2 Ga+

Washer 9/32 x 1-1/4 x 16 Ga°

* Washer, Lock 1/4

Bolt, Hex 1/4o28 x 3/4 Gr. 5

Engine, Briggs & Stratton

Model No. 135202 Type 0119-0t

*STANDARD HARDWARE-- PURCHASE LOCALLY

NOTE: All component dimensions given in U.S+ inches..

1inch = 25+4 mm

REPAIR PARTS

5HP 24" TILLER --MODEL NUMBER 917.298353

DECALS

KEY PART

NO. NO,

1 13776O

2 132606

3 127836

4 137539

5 120431X

6 1107t9X

7 132402

8 120075X

-- 137873

-- 137874

DESCRIPTION

Decal, Logo

Decal, Caution, Tine Control

Decal, Hand Placement

Decal, Operation and Lubrication

Decal, HP

Decal, Warning, Rotating Tines

Manual, Owner's (English)

Manual, Owner's (Spanish)

REPAIR PARTS

5 HP 24" TILLER -- MODEL NUMBER 917.298353

ENGINE, BRIGGS & STRATTON -- MODEL NUMBER 135202, TYPE NO. 0119-01

307

741

613

529

528

37 635

308

IREPA_R PARTS

5HP 24" TILLER - - _]ODEL NUMBER 917.298353

ENGIHE, BRnGGS & STRATTON - - MODEL NUMBER 135202, TYPE NO. 0!!9-01

679

256

10"12

9_ 414 153

_ Q_ 542

190A

118

203

191

205

216

779

621

467

__\_ _ 969

208 967

REPAIR PARTS

5 HP 24" TILLER --MODEL NUMBER 917.298353

ENGINE, BRaGGS & STRATTON -- MODEL NUMBER 135202, TYPE NO, 0119-01

356

"A"REQUIRES SPECIAL TOOLS

TO INSTALL SEE REPAIR

INSTRUCTION MANUAL, 23

73 24

20O _a_ O

334

307

332 455 305

121 CARBURETOR OVERHAUL KIT

191

394

1016

163

358 GASKET SET

461

69A

515

456

REPAIR PARTS

5 HP 24" TILLER - - MODEL NUMBER 917.298353

ENGINE, BRIGGS & STRATTON -- MODEL NUMBER 135202 TYPE NO, 0119-01

KEY PART KEY PART

NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 395990

2 297565

3 299819

5 214040

7 272157

8 495774

9 27549

10 94621

11 66578

12 270080

270125

270126

13 94221

14 94679

15 93448

94387

16 492088

230978

18 297602

19 495660

20 294606

21 66768

22 94682

23 297229

24 222698

25 298904

298905

298906

298907

26 298982

299742

298983

298984

298985

27 26026

28 298909

298908

29 299430

390459

30 221890

32 94745

33 211119

34 261044

35 260552

36 26478

37 222443

Cylinder Assembty 40 93312

Bushing, Cylinder

*Seal, Oil 45 260642

Head, Cylinder 46 212733

*Gasket, Cylinder Head 52 271936

Breather Assembly 55 494846

* Gasket, Valve Cover 56 493824

Screw, Breather Mounting 57 262594

Grommet, Breather Tube 58 280406

* Gasket, Crankcase, Standard .0!5"

*Gasket, Crankcase .005"Thick 59 396892

* Gasket, Crankcase .009" Thick 60 393152

Screw, Cylinder Head 2-3/32" 65 94686

Screw, Cylinder Head 2-15/32" 69 280973

Plug, Pipe, Hex Socket 69A 224322

Plug, Oil Drain 73 224632

Crankshaft 81 222263

Gear Pin, Crankshaft 90 495426

Cover Assembly, Crankcase 95 93499

Bushing, Crankcase Cover 96 223793

*Seal, Oil 97 490048

Plug, Oil Filler 108 491177

Screw, Cover Mounting 118 231533

Flywheel, Magneto 121 495606

Key, Flywheel 124 94616

Piston Assembly, Standard Size 127 220352

Piston Assembly .010" Oversize 127A 223789

Piston Assembly 020" Oversize !49 26336

Piston Assembly .030" Oversize 152 260575

Ring Set, Piston, Standard Size I53 490589

Ring Set, Piston, Standard, Chrome t54 93527

Ring Set, Piston _010" Oversize 163 271935

Ring Set, Piston .020" Oversize 180 495405

Ring Set, Piston .030" Oversize I81 494559

Loci(, Piston Pin t90 94712

Pin Assembly, Piston, Standard 190A 94677

Pin Assembly, Piston _005 Over 191 272489

Rod Assembly, Connecting 200 223886

Rod Assembly, Connecting 202 262270

.020" Undersize Crankpin Bore 203 280720

Dipper, Connecting Rod

Screw, Connecting Rod

Valve, Exhaust

Valve, Intake

Spring, Intake Valve

Spring, Exhaust Valve

Guard, Flywheel

Retainer, Intake Valve and Exhaust

Spring

Tappet, Valve

Gear, Cam

*** Gasket, Carburetor Mounting (2)

Housing, Rewind Starter

Pulley, Rewind Starter

Spring, Rewind Starter

Rope, Rewind Starter

(Cut to Required Length)

Insert, Starter Handle

Handle, Rewind Starter

Screw, Housing Mounting

Washer

Screen, Rotating

Loci(, Screw

Carburetor Assembly

Screw, Throttle Valve to Shaft

Throttle, Carburetor

Shaft and Lever, Throttle

Valve and Shaft Group, Choke

Valve, Needle

Carburetor Overhaul Kit

Screw, Hex Head

Plug, Welch

Spring, Needle Valve

Spring, Throttle Adjustment

Screw and Collar

Screw, Machine, Round Head

* Gasket, Air Cleaner Mounting

Tank Assembly, Fuel

Cap, Fuel Tank

Screw, Fuel Tank

Screw, Fuel Tank Mounting 1-3/4"

*** Gasket, Fuel Tank to CarbUretor

Guide, Air

Link, Throttle

Bell Crank

* Included in Gasket Set (495603)

** Included in Carburetor Overhaul Kit (495606)

*** Included in both Gasket Set (495603), and

Carburetor Overhaul Kit (495606)

NOTE: All component dimensions given in U.& inches

1 inch = 254 mm

REPAIR PARTS

5HP 24" TILLER - -MODEL NUMBER 917.298353

ENGINE, BRIGGS & STRATTON ,-- MODEL NUMBER 135202, TYPE NO. 0119-01

KEY PART KEY PART

NO, NO. DESCRIPTION NO. NO. DESCRIPTION

204 222962 Bushing, Governor Lever, Fiat 528 231550

205 231520 Screw, Shoulder 529 67838

208 262279 Rod, Speed Control 542 93572

209 262283 Spring, Governor 552 231079

216 262359 Link, Choke 562 92613

219 494845 Gear, Governor 592 231082

220 221551 Washer, Thrust 608 495766

222 490649 Panel, Control 611 391813

223 223455 Lever, Governor Control 613 93935

224 93491 Rivet, Governor' Control Lever 614 93306

Mounting 615 93307

227 490374 Lever Assembly, Governor 616 231077

230 222450 Washer, Governor Lever 621 396847

256 223813 Crank, Bell 634 271853

257 93543 Screw, Sems, Hex Head 635 66538

300 393615 Muffler, Exhaust 676 393757

304 495759 Housing, Blower 679 270382

305 94619 Screw, Blower Housing Mounting 680 221839

306 221511 Shield, Cylinder 741 261696

307 94680 Screw, Cylinder Shield 779 262570

308 224738 Cover, Cylinder Head 851 221798

332 92284 Nut, Flywheel 869 211787

333 397358 Armature Group 870 211172

334 93414 Screw, Armature Mounting 871 262001

337 802592 Plug, Spark 63709

346 93705 Screw, Sems 916 280321

366 398808 Wire, Ground 966 492797

358 495603 Gasket Set 967 491588

363 19069 Flywheel Puller 968 495357

373 92987 Nut, Hex 969 490073

383 89838 Wrench, Spark Plug 971 94018

392 262328 Spring, Fuel Pump Diaphragm 987 398970

394 272538 **Diaphragm 995 223887

414 220982 Washer 1012 490507

432 221377 Cap, Spring 1016 224278

433 93265 Pin, Diaphragm Cover

434 214021 Cover, Diaphragm

435 93141 Screw, Diaphragm Cover

455 224250 Cup, Starter

456 224321 Retainer

459 492833 Pawl, Starter

461 262626 Pin, Spring

467 280715 Knob, Control

5t 5 262625 Spring

526 94659 Screw, Sems, Tank Bracket Mount,

527 223786 Clamp, Breather Tube

Tube, Breather

Grommet, Breather Tube

Screw

Bushing, Governor Crank

Bolt, Governor Lever

Nut, Hex

Starter Assembly, Rewind

Fuel Pipe and Clip Assembiy

Screw, Hex Head, Shoulder

Pin, Cotter

Retainer, E-Ring

Crank, Governor

Switch, Stop

Washer, Throttle Shaft, Foam

Etbow, Spark Plug

Deflector, Exhaust, Side OutLet

Washer, Foam

Washer, Brass

Gear, Timing

Link, Speed Control

Cable Ter rninal, Ignition

Seat, Intake Valve, Standard

Seat, Exhaust Valve, Standard

Guide, Exhaust Valve

Guide, Intake Valve

Rack, Gear Control

Base, Air Cleaner

Filter, Air Cleaner

Cover, Air Cleaner

Screw, Air Cleaner

Screw, Hex ',-lead

Seal, Throttle Shaft

Lever', Bracket Assembly

Retainer', Link

Spacer

RPM Settings: Low Speed: 1750-1950

High Speed: 3400-3600

* Included in Gasket Set (495603)

** Included in Carburetor Overhaul Kit (495606)

*** Included in both Gasket Set (495603), and

Carburetor Overhaul Kit (495606)

NOTE; A!l component dimensions given in US, inches

1 inch = 25,4 mm

i1,1i i, i ,i,, ,,,,11, i i

in , ,,11 i

,11, iiii ii iir1111,1, ,,i,, '1 I

SERVICE NOTES

,,i,1,,,111ii , ,i,ii, ,, i iiii, i

MODEL NO.

917.298353

HOW TO ORDER

REPAIR PARTS

Each tiller has its own model number, Each engine has its own model

number.

The model numbe_ for your tiller will be found on a plate attached to the

right hand engine bracket.

The model number for your engine will be found on the blower housing of

the engine.

All parts listed herein may be ordered from any Sears, Roebuck, and Co.

Service CenteUDepartment and most Retail Stores.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOW-

ING INFORMATION;

,PRODUCT - FRONT TINE TILLER

• MODEL NUMBER - 917.298353

, ENGINE MODEL NUMBER - 135202, TYPE NUMBER 0119-01

• PART NUMBER

,PART DESCRIPTION

Your Sears merchandise has added value when you consider Sears has

service units nationwide staffed with Sears trained technicians.,, profes-

sional technicians specifically trained to insure that we meet our pledge

to you, we service what we sell.

ii i i iiill IIIIII,MI Ill ,111,1,'11,,, Ill II ,I,II,II I

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

i i ii,mll,llll

137873 7.7.93 PRINTED IN THE USA

Craftsman 917298353 User Manual TILLER Manuals And Guides L0804229

CRAFTSMAN Front Tine, Gas Tiller Manual L0804229 CRAFTSMAN Front Tine, Gas Tiller Owner's Manual, CRAFTSMAN Front Tine, Gas Tiller installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation