Craftsman 973111400 User Manual DRILL DRIVER Manuals And Guides L0102033

CRAFTSMAN Drill Reversing Manual L0102033 CRAFTSMAN Drill Reversing Owner's Manual, CRAFTSMAN Drill Reversing installation guides

User Manual: Craftsman 973111400 973111400 CRAFTSMAN DRILL-DRIVER - Manuals and Guides View the owners manual for your CRAFTSMAN DRILL-DRIVER #973111400. Home:Tool Parts:Craftsman Parts:Craftsman DRILL-DRIVER Manual

Open the PDF directly: View PDF PDF.
Page Count: 15

Owner's Manual
IrRRFT MRN°I
3/8 in. CORDLESS DRILL-DRIVER
Variable Speed /Reversible
Model No.
973.111400
Save this manual for
future reference
CAUTION: Read and follow all
Safety Rules and Operating Instructions
before first use of this product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.comlcraftsman
972000-775
7-00
• Safety
•Features
•Operation
•Maintenance
• Parts List
®
•Warranty ........................................................................................................................................................ 2
• introduction and Product Specifications ............................................................................................. 2
•Rules For Safe Operetien ........................................................................................................................... 3-5
A. Important Safety Rules For Battery Tools ........................................................................... 4
B. Important Safety Instructions For Charger .,k......... _.:................................................ 4
ill Accessories ............................................................................................................................................. 6
• Features .................................................................................................................................................. 6
• Operation ....................................................................................................... 7-12
• Maintenance ............................................................................................................ _........................... 13
• Battery Pack Removal and Preparation For Recycling ................................................................................ 14
U Exploded View and Repair Parts List ................................................................................................... 15
• Parts Ordering /Service ............................................................................................................................... 16
FULL ONE YEAR WARRANTY ON CRRFTSHRN 318 in. DRILL-DRIVER
If this CRRFTSH RN 3/8 in. Drill-Driver fails to give complete satisfaction within one year from the date of p_r-
chase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED
STATES, and Sears will repair it, free or charge. _,
If this ERRFT$1VlRN 3/8 in. Drill-Driver is used for commerciai or rental purposes, this warranty applies for only g0
days from the date of purchase.
This warranty gives you specitie legal rights, and you may also have other rights which vary from state to state,
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Your drill driver has many features for making drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this drill-driver making it easy
to maintain and operate.
_i, CAUTION: Carefu y read through this entire
owner's manual before using your new drill-driver.
Pay close attention to the Rules For Safe
Operation. Warnings and Cautions. If you use
your drill-driver properly and only for what it is
intended, you will enjoy years of safe, reliable
service.
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
Charge Rate
3/8 in.
16.8 Volts DC
120 volts. 60 Hz, AC Only
0- 350 /0- 1300 RPM
Variable Speed - Reversible
1 Hour
2
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. ]'he safety warnings do
not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL MEANING
ASAFETY ALERT SYMBOL:
Indlcateswamlngorcaution. Maybeusedineonjun_ionwithothersymbolsorpi_ographs.
AWARNING: Failure to obey a safety warning can result in serious injury to yourself or to others,
Always follow the safety precautions to reduce the risk of Nre, electric shock and personal Injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shack
and personal injury.
NOTE: Advises you of information or instructid_s vital to the operation or maintenance of the equipment.
_k WARNING: Do not to this tool •
attempt operate
until you have read thoroughly and understand
completely all instructions, safety rules, etc.
contained in this manual. Failure to comply can
result in accidents involving fire, electric shock, or
serious personal injury. Save owner's manual and
review frequently for continuing safe operation,
and instructing others who may use this tool.
READ ALL INSTRUCTIONS
•KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitationsas well as the specific potential hazards
related to this tool.
•GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For exampte: Pipes, radiators, ranges, refrigerato_
enclosures.
•KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
•AVOID DANGEROUS ENVIRONMENT. Don't use
power tool in damp or wet locations or expose to
rain. Keep work area welt lit.
•KEEP CHILDREN AND VISITORS AWAY. Al!
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact too] or extension cord.
•STORE IDLE TOOLS, When not in use tools
should be stored in adry and high or locked-up
place - out of the reach of children.
•DON'T FORCE TOOL. It will do the job better and
safer st the rate for which it was designed
USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example - A
circular saw shou[d never be used for cutting tree
limbs or logs.
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury Rubber
gloves and nonskid footwear are recommended
when working outdoors. Wear protective hair
covering to contain long hair and keep it from being
drawn into nearby air vents.
•ALWAYS WEAR SAFETY GLASSES, Everyday
eyeglasses have on[y impact-resistant lenses; they
are NOT safety glasses.
• PROTECT YOUR LUNGS, Wear a face mask or
dust mask if operation is dusty
•PROTECT YOUR HEARING. Wear hearing
protection during extended periods of operation.
• SECURE WORK, Usa clamps or avise to hold
work. It's safer than using your hand and it frees
both hands to operate tool.
•DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
MAINTAIN TOOLS WITH CARE, Keep tools sharp
at all times, and clean for best and safest perfor-
mance. Follow (nstructions for lubricating and
changing accessories.
REMOVE ADJUSTING KEYS AND WRENCHES,
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
RULES FOR SAFE OPERATION (Continued)
•NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could Ignite flam-
mable liquids, gases, or fume&
•KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE, Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any strong
solvents to clean your tool.
•STAY ALERT. Watch whet you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
[]
[]
•CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefuJiy checked to determine that it wi]]
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
Aguard or other part that is damaged should be
properly repaired or replaced by an authorized []
service center unless indicated elsewhere in this
instruction manual.
•DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
•DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
•DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE. Do
not touch metal parts when drilling; grasp only the
insulated handle(s) or plastic housing when using
this tool. Make sure hidden electrical wiring, water
pipes, and mechanical hazards are not in the path
of the bit when drttling into awall.
• INSPECT FOR and remove all nails from lumber
before drilling. _,
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
[] Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
•USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. DO not substitute any
other charger, Use of another charger could cause
batteries to explode causing possible serious
injury.
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT, They may
explode.
DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
•Your battery tool should be charged in alocation
where the temperature is more than 50°F but less
than 100°F.
•Under extreme usage or temperature conditions,
battery leakage may occur, If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with Lemon juice
or vinegar. If liquid gets in your eyes, flush them
with dean water for at least 10 minutes, then seek
immediate medical attention.
If carrying your battery tool at your side, make sure
it is not running and your finger is not on the
switch. Avoid accidental starting.
SECURE WGRK before apply{ng power. NEVER
hold workpiece in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
•SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating
instructions for charger item number 9-11118
(982139-001 ),
•Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger.
_WARNING: To reduce risk of injury, charge only
nickel-cadmium type reohargeab[e batteries. Other
types of batteries may burst causing personal
injury and damage.
• Do not expose charger to rain or snow.
[] Usa of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electric shock, or injury to persons.
•To reduce risk of damage to charger body and
cord, pull by plug body rather than cord when
disconnecting charger.
• Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
RULES FOR SAFE OPERATION (Continued)
• An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in arisk of fire and electric shock.
If extens(on cord must be used, make sure:
a. That pins on plug of extension card are the
same number, size and shape as those of plug
on charger, k
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as spee(fied below:
Cord Length (Feet} 25' 50' 100'
Cord Size (AWG) 16 16 16
Note'. AWG = American Wire Gage
•DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. Jfdamaged,
have replaced immediately by a qualified
serviceman.
•Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
• Do not dlsassemb(e charger; take it to a qualified
serv(ceman when service or repair is required..
Incorrect reassembly may result (n arisk of electric
shock or fire,
• To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk.
• Do not use charger outdoors,
• Disconnect charger from power supply when not in
use.
•SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct others who may
use this tool. If you (oan someone this tool, loan
them these instructions also.
_k.WARNING: Some dust created by power
sanding, saw(ng, grinding, dr((ling, and other
construction activ(ties contaiRs chemicals known to
cause cancer, birth detects or other reproducl)ve
harm. Some examples of these chemicals are:
- lead from lead-based paints,
•crystaUite silica from bricks and cement
and other masonry products, and
•arsenic and chromium from chemically=
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicaSs: work in a we(I
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
• particles,
Look for this symbol to point out important safety precautions, it means attention!!! Your
safety is involved.
,_ WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beg(nning power tool operation, always
wear safety goggles or safety glasses with side shields and a fu(I face shield when needed.
We recommend Wide Vision S_fety Mask for use over eyeglasses or standard safety
glasses with side shields, available at Sears Retail Stores.
Thefollowing recommended accessories are currently available at Sears Retail Stores.
• 6-Pc, Extra Length Magnite Power Bit Set • High Speed Bits (For Wood or Metal)..3/4 in. Max
• 30-Pc, Power Screwdriver/Nutdriver Set and Case • Keyless Chuck (Item No..9_-20988)
• 17-Pe. Power Screwdriver/Nutdriver Set and Case
_kWARNING: The use of attachments or accessories nat listed might be hazardous.
KNOW YOUR DRILL-DRIVER
See Figure 1,
Before attempting to use any tool familiarize yourself
with all operating features and safety requirements.
BATTERY PACK
WRIST STRAP
See Figure 1.
A wrist strap is provided to reduce the chances of
dropping your drill-driver. Place one hand through the
wrist strap when carrying tool.
TWO-SPEED BIT STORAGE LEVEL
GEARTRAIN(HI-LO)
KEYLESSCHUCK
YELLOW AND GREEN LIGHTS
INDICATE SOFT START MODE
GREEN LIGHT "ON"
INDICATES SLOW CHAR(31NG
MODE OR FULLYCHARGED
SWITCH
TRIGGER
DIRECTIONOF
ROTATLONSELECTOR
)
BATTERY
CHARGER
WRIST STRAP
_SCREWDRIVER BITS
Fig. 1
_. WARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
6
_i WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown into your eyes. resulting in possible
serious injury.
_k WARNING: Do not allow familiarity with your
drill-driver to make you careless. Remember that
a careless fraction of a second is sufficient to
inflict severe injury.
CHARGING BATTERY PACK
The battery pack for this tool has been shipped in a
low charge condition to prevent possible problems.
Therefore, you should charge it untlt light on front of
charger changes from red to green.
Note= Batteries will not reach full charge the first time
they are charged. AlLow several cycles (drilling
fol[owed by recharging) for them to become fully
charged.
TO CHARGE
• Charge battery pack only with the charger
provided.
•Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
•Connect charger to power supply.
• Place battery pack in charger aligning raised rib in
charger with groove in battery pack.
• Press down on battery pack to be sure contacts on
battery pack engage properly with charger
contacts.
•Normally, the yellow and green lights on charger
wilt come on. This indicates charger is in soft start
mode and should switch to fast charge mode
within 5 minutes. When charger is in fast charge
mode the red light wilt come on. If after a period of
15 minutes the yellow and green lights remain on,
remove battery pack, wail 1 minute and relnsert
battery pack In charger. If the yellow and green
lights continue to remain on after an additional 15
minutes, the battery pack is damaged and will not
accept acharge. Return battery pack to your
nearest Sears Repair Center for checking or
replacing.
• When your battery pack becomes fully charged, the
red light will turn OFF and the green light will turn
ON.
•After normal usage, 1 hour of charging time is
required to be fully charged. A minimum charge
time of 1-1/2 hours is required to recharge a
completely dLscharged tool,
il The battery pack wilt become slightly warm to the
touch while charging. This is.normal and does not
indicate a problem,
•Do not place charger in an area of extreme heat or
cold. It wi[I work best at normal room temperature,
• When batteries become fully charged, unpLug
charger from power supply and remove the battery
pack.
IMPORTANT INFORMATION FOR RECHARG-
ING HOT BATTERIES
When using your drill-driver continuously, the batteries
In your battery pack will become hot. You should let a
hot battery pack cool down for approximately 30
minutes before attempting to recharge. When the
battery pack becomes discharged and is hot. this will
cause the yellow and green lights on your battery
charger to come on Instead of the red light, The yellow
and green lights indicate soft start mode and will
_witch to green only, indicating slow ¢harge mode
The red light indicates fast charge mode, 1 hour
charge time. The green light indicates slow charge
mode, requiring overnight charging for batteries to
reach full charge. If the green ]ight comes on after
letting battery pack cool down, remove it from charger
for additional cooling. Once the battery pack coots
down, you can recharge battery pack in fast charge
mode as normal. Do not leave a hot battery pack in
charger until it cools down. The green light will net go
eft when battery pack cools. If fast charge mode is
desired, you must physically remove a hot battery
pack from the charger, [el it cool, then place it back in
charger after it has cooled down.
Note= This situation only occurs when continuous use
of your drill causes the batteries to become hot. It
does not occur under normal circumstances. Refer to
"CHARGING BATTERY PACK" far normal recharg-
ing of batteries. If the charger does not charge your
battery pack under normal circumstances, return both
the battery pack and charger to your nearest Sears
repair center for electrical check.
SWITCH
See Figure 2,
To turn your drill ON, depress the switch trigger. To
turn it OFF. release the switch trigger.
SWTCHJ
TRIGGER
_SELECTOR
Fig. 2
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
Note: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned, this is a
normal part of the switch function, ?,
TWO-SPEED GEAR TRAIN
See Figure 3.
Your drill has a two-speed gear traln designed for
drilling or driving at H! or LO speeds. A slide switch is
located on top of your drill to select either HI or LO
speed. When using drill in the HI speed range, speed
w{[I increase and unit will have less power and torque.
When using drill ]n the LO speed range, speed will
decrease and unit will have more power and torque.
Use HI speed for fast drilling or driving applications
and LO speed for high power and torque applications.
HISPEED
LO SPEED TWO SPEED
GEAR TRAIN(HI-LO)
TO INSTALL BATTERY PACK
•Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 5.
• Place battery pack in your drill. Align raised rib
inside drill with groove on battery pack.
See Figure 4.
BA'n'ERYPACK
LATCHES
DEPRESSLATCHESTO
RELEASEBA'i-rERYPACK Fig 4
• Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in
drill before beginning operation,
_1= CAUTION; When p[acing battery pack in your
drill, be sure raised rib inside drill aligns with
groove on battery pack and latches snap into
place properly. Improper assembly of battery
pack can cause damage to internal components
TO REMOVE BATTERY PACK
•Lock switch trigger on your drill by placing the
direction of rotation selector in center position
See Figure 5.
• Locate latches on end of battery pack and depress
to release battery pack from your drill
See Figure 4.
• Remove battery pack from your drill.
SWITCH LOCK
See Figure 5.
The switch trigger can be locked in the OFF position,
This feature can be used to prevent the possibility of
accidental starting when not in use. To lock switch
trigger, place the direction of rotation selector in
center position.
CENTER POSITION
(LOCK)
FORWARD REVERSE -_16in,
SWITCH
TRIGGER
SELECTOR
Fig. 5
_ WARNING: Battery tools are always in
operating condition Therefore, switch should
always be locked when not in use or carrying at
your aide.
REVERSIBLE
See Figure 5.
This too! has the feature of being reversible, The
direction of rotation is cor_trolled by a selector Located
above the switch trigger. With the drill held in normal
operating position, the direction of rotation selector
should be positioned to the left of the switch for
drilling. The drilling direction is reversed when the
selector is to the right of the switch. When the selector
is in center position, the switch trigger Is locked•
_k CAUTION; To prevent gear damage, always
allow chuck to come to a complete stop before
changing the direction of rotation or the two-
speed gear train (hi-lo).
To stop, release switch trigger and allow the chuck to
come to a complete stop.
CHARGER
See Figure 5.
Your charger has a "key hole" hanging feature for ,_
convenient, space saving storage. Screws should be
installed so that center distances are 1-7/16 inches
apa_.
BACKSIDEOF CHARGER Fig. 6
KEYLESS CHUCK
See Figure 7.
Your drill has a keyless chuck. As the name implies, you
can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand.
Rotate the chuck body with your other hand. The arrows
on the chuck indicate which direction to rotate the chuck
body in order to LOCK (tighten) or UNLOCK (reJease)
the drill bit.
UNLOCK
DRILL BIT
LOCK
(TIGHTEN)CHUCK COLLAR
Fig, 7
_WARNING: Do not hold chuck body with one
hand and uSe power of the drill to tighten chuck
jaws on drill bits. Chuck body could slip in your
hand or your hand could slip and come in contact
with rotating drill bit. This could cause an
accident resulting in serious personal injury.
9
INSTALLING BITS
See Figure 8.
• Lock the switch trigger by placing the direction of
rotatmn selector in center position. See Figure 5.
Ii Open or close chuck jaws to a point where the
opening is slightly larger than the bit size you
intend to use Also, raise the front of your drilL
slightly to keep the bit from falling out of the chuck
jaws,
• Insert drill bit straight into chuck the full length of
the jaws as shown in Figure 8.
• Tighten the chuck iaws on drill b{t
CHUCKJAWS CHUCKBODY
DRILLBIT
CHUCKCOLLAR
RIGHT Fig, 8
• To tighten the chuck jaws on drill bit; grasp and
hold the collar of the chuck wLth one hand, while
rotating the chuck body with your other hand.
Note: Rotate the chuck body in the direction of
the arrow marked LOCK to tighten chuck jaws,
•Do not use awrench to tighten or loosen the
chuck jaws.
,_ WARNING: Make sure to insert drill bit straight
into chuck jaws. Do not insert drill bit into chuck
jaws at an angle then tighten as shown in Figure
9. This could cause drill bit to be thrown frem drill,
resulting in possible serious personal injury or
damage to the chuck.
REMOVING BITS
See F/gum 8,
• Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure E.
• Loosen the chuck jaws from drill bit.
• To loosen: grasp and hold the collar of the chuck
with one hand. while rotating chuck body with your
other hand. Note: Rotate chuck body in the
direction of the arrow marked UNLOCK to loosen
chuck jaws.
•Do not use a wrenoh to tighten or loosen the
chuck jaws.
• Remove drill bit from chuck jaws.
ADJUSTABLE TORQUE CLUTCH
Your drill is equipped with an adjustable torque clutch
for ddving different _pea of screws into different mate-
rials. The proper setting depends on the type of mats-
rial and the size of screw you are using.
TO ADJUST TORQUE
ill Identi_ the twenty four torque indicator settings
(ocated on the front of your drill. See Figure 10,
•Rotate adjusting ring to the desired setting.
•1 - 4 For driving small screws.
5 - 8 For driving screws into soft
materla[,
• 9 - 12 For driving screws into soft and hard
materials.
•13 - 16 For drivLng screws in hard wood.
-17- 20 For driving large screws.
• 21 - <LIl For heavy drilling.
TO DECREASE
TORQUE
RING
TOINCREASE
TORQUE
Fig. 9 Fig. lO
10
Note: Remember the two-speed feature (HI-LO) when
setting torque. The amount of torque will vary depend-
ing on which speed setting you have your drill-driver.
Switching to LO speed will increase torque. Switching
to HI speed will decrease torque.
BIT STORAGE
See Figure 11.
When not in use, bits provided with your drill can be
placed in the storage area located on the top of your
drill as shown in Figure 11.
SCREWDRIVER BITS
DRILLING
See Figure 13.
BIT STORAGE AREA Fig, 11
_11 WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to de so could result In objects
being thrown into your eyes, resu[ting in possible
serious injury.
LEYEL DRILLING ,_
See Figure 12
Aconvenient new feature provided with your drill is a
]evel. It Jsrecessed in the motor housing on top of
your drill. It can be used to keep drill bits level during
drilling operations.
LEVEL
Fig. 12
Fig, 13
When drilling hard smooth surfaces use a center
punch to mark desired hole location. This will prevent
the drill bit from slipping off center as the hole is
started. However, the low speed feature allows
starting holes without center punching tf desired. To
accomplish this, simpty operate your drill at a low
speed until the hole is started,
The material to be drilled should be secured in a vise
or with clamps to keep it from turning as the drill bit
rotates.
Hold tool firmly and place the bit at the point to be
drilled, Depress the switch trigger to start tool.
Move the drill bit into the werkpJece applying only
enough pressure to keep the bit cutting. Do not force
or apply side pressure to elongate a hole.
,_ WARNING; Be prepared far binding or bit
breakthrough. When these situations occur, drill
has atendency to grab and kick opposite to the
direction of rotation and could cause loss of
control when breaking through material. If not
prepared, this loss of control can result in
possible serious injury.
_/hen drilling metals, use elight oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
11
CHUCK REMOVAL
See Figures 14. 15, and 16.
The chuck must be removed in order to use some
accessories. To remove:
•Lock the switch trigger by ptacing the direction of
rotation selector in center position. See Figure 5.
U Insert a 5/16 inch or larger hex key wrench into the
chuck of your drill and tighten the chuck jaws
securely.
• Tap the hex key wrench sharply with a mallet in a
clockwise direction See Figure 14. This will
loosen the screw in the chuck for easy removal,
MALLET
KEYLESS CHUCK
CHUCKJAWS HEXKEY
WRENCH Fig. 14
k
Open chuck jaws and remove wrench, Remove
the chuck screw by turning it in a clockwise
direction, See Figure 15.
Note: The screw has left hand threads.
Insert hex key wrench in chuck and tighten chock
jaws securely. Tap sharply with amallet in a
counterclockwise direction. This will loosen chuck
on the spindle, It can now be unscrewed by hand.
See Figure 16.
Fig. 16
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on spindle and develop
a wobble. Periodically check chuc_ screw for tight-
ness. Aloose screw may cause the chuck jaws to
bind end prevent them from closing.
To tighten, follow these steps:
iLock the switch trigger by placing the direction of
rotation selector in center position. See Figure 5.
• Open the chuck jaws.
• Insert hex key wrench into chuck and tighten
chuck Jaws securely. Tap hex key wrench sharply
with emallet in a clockwise direction. This will
tighten chuck on the spindle.
• Open the chuck jaws and remove hex key
wrench.
•Tighten the chuck screw.
Note: The chuck screw has left hand threads.
FIg. 15
12
_IL WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create ahazard or cause product
damage,
Avoid using solvents when cleaning plastic parts.
Most plastics ere susceptible to damage from variou_
types of commercial solvents and may be damaged "
by their use. Use clean cloths to remove dirt, dust, oil.
grease, etc.
,_, WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic,
Do not abuse power tools. Abusive practices can
damage tool as welt as workplece.
Only the parts shown on parts list, page 15, ere
intended to be repaired or replaced by the customer
AIJ other parts should be replaced by a Sears Service
Center.
_WARNING: Do not attempt to modify this tool or
create accessories not recommended for use
with this tool. Any such alto'ration or modification
is misuse and could result in a hazardous
condition leading to possible serious personal
injury.
BATTERIES
Your drill's battery pack is equipped with nickel-
cadmium rechargeable batteries. Length of service
from each charging will depend on the type of work
you are doing.
The batteries in this tool have been designed to _,
provide maximum trouble free life, However, like all
batteries, they will eventually wear out. Do not
disassemble battery pack and attempt to replace the
Datteries. Handling of these batteries, especially when
wearing rings end jewelry, could result in a serious
burn.
To obtainthe longest possible battery life, we suggest
the following:
•Store and charge your batteries in a cool area.
Temperatures above normal room temperature
will shorten battery life.
• Never store batteries in a discharged condition,
Recharge them immediately after they are
discharged.
• All batteries gradually lose their charge. The
higher the temperature the quicker they lose their
charge. If you store your tool for long periods of
time without using it, recharge the batteries every
month or two. This practice will prolong battery
life.
OVERLOAD
Your drill has a built in overload protector to protect the motor during overloading or prolonged use. The
overload protector automatically activates to break the circuit. When this occurs, allow your dri]l to coo[ a few
seconds before resuming operation.
13
To preserve natural resources, please
recycle or dispose of batteries
properly.
This product contains nickel-
cadmium batteries. Local, state or
federal laws may prohibit disposal of
nickel-cadmium batteries in ordinary
trash.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
BATTERY PACK REMOVAL AND
PREPARATION FOR RECYCLING
._. WARNING: Upon removal, cover the battery
pack's terminals w[th heavy duty adhesive tape
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Nickel-
cadmium batteries must be recycled or disposed
of properly. Also, never touch both terminals with
meta{ objects and/or body parts as short circuit
may result. Keep away from children. Failure to
comply with these warnings could result in fire
and/or serious injury.
i,,,
m im
14
CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER- MODEL NO, 973.111400
The model number will be found on a plate attached to the motor hous{ng. Always mention the model I
I
number in all correspondence regarding your 3/8 in. CORDLESS DRILL.DRIVER or when ordering I
repair par_s.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
2
3
Key Pa_
No. Number
1616478-003
2 973015-001
3 967216-004
4 *Item No._-11117
5 "Item No. 9-11118
6 982143-001
972000-775
PARTS LIST
Description Quart.
Screw (Special) ................................................................. 1
Chuck (Item No. 9-20988) .................................... 1
Wrist Strap ........................................................................ 1
Battery Pack (982138-001) .............................................. 1
Charger (982139-001 ) ...................................................... 1
Carrying _aae -' Not Shown ......................................... 1
Owner's Manual
= Can Be Purchased Thru RSOS (Retail Special Order System)
15

Navigation menu