Craftsman 10 In Contractor Saw Sears21833 Owners Manual 218330_Bil_oipm_V5

Craftsman-Contractor-351-21833-Users-Manual-161072 craftsman-contractor-351-21833-users-manual-161072

: Craftsman Craftsman-10-In-Contractor-Saw-Sears21833-Owners-Manual-661853 craftsman-10-in-contractor-saw-sears21833-owners-manual-661853 craftsman pdf

Open the PDF directly: View PDF .
Page Count: 36

Sears Brands Management Corp., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

31105.04 Draft (02/09/10)

Operator’s Manual

10″

CONTRACTOR TABLE SAW

Model No.

351.218330

CAUTION:

Read and follow all Safety

Rules and Operating

Instructions before First

Use of this Product. Keep

this Manual with Tool.

•Safety

•Unpacking

•Assembly

•Operation

•Maintenance

•Parts List

•Español

2

TABLE OF CONTENTS

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20

Repair Protection Agreement . . . . . . . . . . . . . . . . . . . . . . . 20

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

Parts Illustration and List . . . . . . . . . . . . . . . . . . . . . . . . 24-35

Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-59

WARRANTY

ONE-YEAR FULL WARRANTY ON CRAFTSMAN

TOOL

If this Craftsman tool fails due to a defect in material or

workmanship within one year from the date of purchase, call

1-800-4-MY-HOME® TO ARRANGE FOR FREE REPAIR (or

replacement if repair proves impossible).

This warranty does not cover the blade, which is an

expendable part.

If this tool is ever used for commercial or rental purposes, this

warranty will apply for only 90 days from the date of purchase.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

SAFETY RULES

WARNING: For your own safety, read all of the instructions

and precautions before operating tool.

PROPOSITION 65 WARNING: Some dust created by

using power tools contain chemicals known to the state of

California to cause cancer, birth defects or other reproductive

harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other

masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures vary, depending on how often

you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area and work with

approved safety equipment. Always wear OSHA/NIOSH

approved, properly fitting face mask or respirator when using

such tools.

CAUTION: Always follow proper operating procedures as

defined in this manual — even if you are familiar with use of

this or similar tools. Remember that being careless for even a

fraction of a second can result in severe personal injury.

BE PREPARED FOR JOB

• Wear proper apparel. Do not wear loose clothing, gloves,

neckties, rings, bracelets or other jewelry which may get

caught in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear safety glasses complying with United States ANSI

Z87.1. Everyday glasses have only impact resistant lens-

es. They are NOT safety glasses.

• Wear face mask or dust mask if operation is dusty.

• Be alert and think clearly. Never operate power tools when

tired, intoxicated or when taking medications that cause

drowsiness.

PREPARE WORK AREA FOR JOB

• Keep work area clean. Cluttered work areas invite acci-

dents.

• Do not use power tools in dangerous environments. Do not

use power tools in damp or wet locations. Do not expose

power tools to rain.

• Work area should be properly lighted.

• Keep visitors at a safe distance from work area.

• Keep children out of workplace. Make workshop childproof.

Use padlocks, master switches or remove switch keys to

prevent any unintentional use of power tools.

• Keep power cords from coming in contact with sharp

objects, oil, grease and hot surfaces.

TOOL SHOULD BE MAINTAINED

• Always unplug tool prior to inspection.

• Consult manual for specific maintaining and adjusting pro-

cedures.

• Keep tool lubricated and clean for safest operation.

• Remove adjusting tools. Form habit of checking to see that

adjusting tools are removed before switching machine on.

• Keep all parts in working order. Check to determine that

the guard or other parts will operate properly and perform

their intended function.

• Check for damaged parts. Check for alignment of moving

parts, binding, breakage, mounting and any other condi-

tion that may affect a tool’s operation.

• A guard or other part that is damaged should be properly

repaired or replaced. Do not perform makeshift repairs.

(Use parts list provided to order replacement parts.)

• Maintain proper adjustment of rip fence and blade guard.

• Never adjust saw while running. Disconnect power to avoid

accidental start-up.

• Have damaged or worn power cords replaced immediately.

• Keep blade sharp for efficient and safest operation.

KNOW HOW TO USE TOOL

• Use right tool for job. Do not force tool or attachment to do

a job for which it was not designed.

• Disconnect tool when changing blade.

• Avoid accidental start-up. Make sure that the tool is in the

“off” position before plugging in, turning on safety discon-

nect or activating breakers.

• Do not force tool. It will work most efficiently at the rate for

which it was designed.

• Keep hands away from blade and moving parts and cutting

surfaces.

• Never leave tool running unattended. Turn the power off

and do not leave tool until it comes to a complete stop.

• Do not overreach. Keep proper footing and balance.

• Never stand on tool. Serious injury could occur if tool is

tipped or if blade is unintentionally contacted.

© Sears, Roebuck and Co.

3

• Know your tool. Learn the tool’s operation, application and

specific limitations.

• Handle workpiece correctly. Press firmly against table.

Protect hands from possible injury.

• Turn machine off if it jams. Blade jams when it digs too

deeply into workpiece. (Motor force keeps it stuck in the

work.)

• Feed work into the blade only as recommended in

“Operation.”

WARNING: For your own safety, do not operate your saw until it

is completely assembled and installed according to instructions.

STABILITY OF SAW

If there is any tendency for the saw to tip over or move during

certain cutting operations, such as cutting extremely heavy

panels or long heavy boards, the saw should be bolted down.

If you attach any kind of extensions over 24″wide to either

end of the saw, make sure you either bolt the saw to the floor,

as appropriate, or support the outer end of the extension from

the bench or floor, as appropriate.

LOCATION

The saw should be positioned so neither the operator nor a

casual observer is forced to stand in line with the saw blade.

KICKBACKS

A kickback occurs during a rip-type operation when a part or

all of workpiece is thrown back violently toward operator.

Keep your face and body to one side of the saw blade, out of

line with a possible kickback.

Kickbacks and possible injury from them can usually be avoid-

ed by:

• Maintaining rip fence parallel to saw blade.

• Keeping saw blade sharp. Replace or sharpen anti-kick-

back pawls when points become dull.

• Keeping saw blade guard, spreader, and anti-kickback

pawls in place and operating properly. The spreader must

be in alignment with the saw blade and the pawls must

stop a kickback once it has started. Check their action

before ripping.

• Not ripping work that is twisted or warped or does not

have a straight edge to guide along the rip fence.

• Not releasing work until you have pushed it all the way

past the saw blade.

• Using a push stick for ripping widths less than 6 inches.

• Not confining the cutoff piece when ripping or crosscutting.

PROTECTION: EYES, HANDS, FACE, BODY, EARS

• If any part of your saw is missing, malfunctioning , or has

been damaged or broken (such as the motor switch, elec-

tronic controls, other operating control, a safety device or

power cord), cease operating immediately until the partic-

ular part is properly repaired or replaced.

• Wear safety goggles that comply with United States ANSI

Z87.1 and a face shield or dust mask if operation is dusty.

Wear ear plugs or muffs during extended periods of oper-

ation.

• Small loose pieces of wood or other objects that contact

the rear of the revolving blade can be thrown back at the

operator at excessive speed. This can usually be avoided

by keeping the guard and spreader in place for all thru-

sawing operations (sawing entirely thru work) and by

removing all loose pieces from the table with a long stick

of wood immediately after they are cut off.

• Use extra caution when the guard assembly is removed for

resawing, dadoing, or rabbeting—replace guard as soon

as that operation is completed.

• Never turn the saw ON before clearing the table of all

tools, wood scraps, etc., except the workpiece and related

feed or support devices for the operation planned.

• Never place your face or body in line with the cutting tool.

• Never place your fingers or hands in path of saw blade or

other cutting tool.

• For rip or rip-type cuts, the following end of a workpiece to

which a push stick or push board is applied must be

square (perpendicular to the fence) in order that feed

pressure applied to the workpiece by the push stick or

block does not cause the workpiece to come away from

the fence, and possibly cause a kickback.

• During rip and rip-type cuts, workpiece must be held down

on table and against fence with a push stick, push block,

or featherboards, as applicable (see Figures 1a and 1b,

page 4).

The push stick and push block examples shown below are use-

ful for keeping hands and fingers away from saw blade during

ripping, rabbeting and dadoing. Apply downward pressure and

push workpiece through the cut and past the blades. Several

other configurations may be suitable for safe operation.

Featherboards are used to keep the work in contact with the rip

fence or table during the cutting operation. Use of featherboards

can help to prevent kickbacks and binding. Featherboards

should be used for all “non thru-sawing” operations.

• Never reach in back of the cutting tool with either hand to

hold down or support the workpiece, remove wood scraps,

or for any other reason. Avoid awkward operations and

hand positions where a sudden slip could cause fingers or

hand to move into a saw blade or other cutting tool.

• Do not perform layout, assembly, or setup work on the

table while the cutting tool is rotating.

• Do not perform any operation freehand—always use either

rip fence or miter gauge to position and guide the work.

• Never use the rip fence when cross-cutting or the miter gauge

when ripping. Do not use rip fence as a length stop. Never

hold onto or touch free-end of workpiece or a free-piece that

is cut off, while power is ON and/or saw blade is rotating.

• Shut the saw OFF and disconnect power source when

removing the table insert, changing the cutting tool,

removing or replacing the blade guard, or making adjust-

ments.

• Provide adequate support to the rear and sides of the saw

table for wide or long workpieces.

• Plastic and composition materials (like hardboard) may be

cut on your saw. However, since these are usually quite

hard and slippery, the anti-kickback pawls may not stop a

kickback. Therefore, be especially attentive to following

proper setup and cutting procedures for ripping. Do not

stand, or permit anyone else to stand, in line with a poten-

tial kickback.

• If you stall or jam the saw blade in the workpiece, turn saw

OFF and remove the workpiece from the saw blade.

Check to see if the saw blade is parallel to the miter

gauge grooves and if the spreader is in proper alignment

with the saw blade. If ripping at the time, check to see if

the rip fence is parallel with the saw blade. Readjust as

required.

• Do not remove small pieces of cutoff material that may

become trapped inside the blade guard while the saw is

running. This could endanger your hands or cause kick-

back. Turn saw OFF and wait until blade stops.

4

• Use extra care when ripping wood with twisted grain or

wood that is twisted or bowed—it may rock on table and

pinch saw blade.

KNOW YOUR CUTTING TOOLS

• Dull, gummy, improperly sharpened or set cutting tools can

cause material to stick, jam, stall saw, or kickback at oper-

ator. Minimize potential injury by proper care and machine

maintenance.

WARNING: Never attempt to free a stalled saw blade with-

out first turning saw OFF.

• Never use grinding wheels, abrasive cutoff wheels, friction

wheels (metal slitting blades), wire wheels or buffing

wheels.

USE ONLY ACCESSORIES DESIGNED FOR SAW

• Crosscutting operations are worked more conveniently and

with greater safety if an auxiliary wood facing is attached

to miter gauge using holes provided. However, facing must

not interfere with proper functioning of saw blade guard.

• Make sure the top of the arbor or cutting tool rotates

toward you when standing in normal operating position.

Also make sure the cutting tool, blade flange and arbor

nut are installed properly. Keep the cutting tool as low as

possible for the operation being performed. Keep all

guards in place whenever possible.

• Do not use any blade or other cutting tool marked for oper-

ating speed less than 4000 RPM. Never use a cutting tool

larger in diameter than diameter for which saw was

designed. For greatest safety and efficiency when ripping,

use maximum diameter blade for which saw is designed,

since under these conditions spreader is nearest the

blade.

• Adjust table inserts flush with table top. Never operate saw

unless proper insert is installed.

24″

5⁄16″(typ.)

120°

87⁄16″

3⁄4″

Clamp to rip fence or

rip fence extension to

keep work on the

table.

Rip Fence

Table

Blade

Clamp to table

to guide work

Use featherboards in combinations as required to control

workpieces.

Miter slot

Figure 1b - Featherboards

5″Long (typ.)

Solid Lumber

Figure 1a - Push Sticks and Push Blocks

135°

15″Long

½″

90° ¾″

12″

2″

2″

6½″

1¾″

1½″

½″

¾″

12″

5″

1″x 45° (2X)

¾″½″

2″

5¼″

1¾″

5

• Never feed material into the cutting tool from the rear of

the saw. An accident and serious injury could result.

THINK SAFETY

Safety is a combination of operator common sense and alert-

ness at all times when the saw is being used.

Never use another person as a substitute for a table exten-

sion, or as additional support for a workpiece that is longer or

wider than basic saw table, or to assist in feeding, supporting

or pulling the workpiece.

Do not pull the workpiece through the saw blade—position

your body at the infeed side of the guard; start and complete

the cut from that same side. This will require added table sup-

port for long or wide workpieces that extend beyond the

length or width of the saw table.

CAUTION: Follow safety instructions that appear on the front

of your saw.

UNPACKING

Refer to Figure 2.

• Open shipping box. Remove all parts, except saw body,

from both styrofoam packing bases and set parts and top

base safely aside.

• Use utility knife to cut down the four corners of the ship-

ping box, fully exposing the bottom packing base.

• Cut away enough styrofoam from motor cover side of

packing base so that, with the aid of an assistant, you can

slide the saw body from the base.

CAUTION: Do not attempt assembly if parts are missing.

Use this manual to order replacement parts.

Check for shipping damage or missing parts. If any parts are

damaged or missing, call 1-800-266-9079 for replacement.

The table saw body comes assembled as one unit. Additional

parts which need to be fastened to the saw should be located

and accounted for before assembling:

A Extension Table (2)

B Dust Chute

C Front Rail (2)

D Rear Rail (2)

E Miter Gauge Assembly

F Blade Guard Assembly

G Dado Insert

H Table Insert

I Handwheel Assembly with Knob (2)

J Rip Fence Assembly

K Rubber Foot (4)

L Anti-kickback Pawl Assembly

M Line Cord Hooks (2)

N Brace

O Rip Fence Storage Hooks (2)

P Blade Guard Storage Hooks (2)

Q Push Stick Storage Hooks (2)

R Push Stick

S Base Panel (4)

T Corner Support (4)

U Caster Set (2)

Hardware Bag #1

M10 x 25 Socket Head Bolt (6)

M10 Lock Washer (6)

M10 Flat Washer (6)

Hardware Bag #2

M8 x 28 Hex Head Bolt (8)

M8 x 25 Hex Head Bolt (8)

M8 x 20 Hex Head Bolt (4)

M8 Lock Washer (20)

M8 Flat Washer (20)

M8 Hex Nut (16)

M8 Acorn Hex Nut (4)

Hardware Bag #3

M6 x 16 Hex Head Screw (2)

M6 Flat Washer (2)

M6 Hex Nut (2)

M6 Lock Washer (2)

Hardware Bag #4

M10 x 25 Socket Head Bolt (4)

M8 x 16 Socket Pan Head Screw (8)

M6 x 12 Socket Pan Head Screw (24)

M6 x 16 Socket Head Bolt (2)

M5 x 12 Socket Head Bolt (4)

M3 x 10 Pan Head Screw (4)

M10 Lock Washer (4)

M6 Hex Nut (2)

M5 Lock Washer (4)

M3 Lock Washer (4)

M10 Flat Washer (4)

M6 Flat Washer (2)

M5 Flat Washer (4)

M3 Flat Washer (4)

Hardware Bag #5

10/13mm Open End Wrench

4mm Hex Wrench

5mm Hex Wrench

8mm Hex Wrench

Figure 2 - Unpacking

F

GH

I

J

KM

N

L

A

B

P

S

U

T

Q

R

O

CE

D

6

IMPORTANT: Table is coated with a protectant. To ensure

proper fit and operation, remove coating. Coating is easily

removed with mild solvents, such as mineral spirits, and a soft

cloth. Avoid getting solution on paint or any of the rubber or

plastic parts. Solvents may deteriorate these finishes. Use

soap and water on paint, plastic or rubber components. After

cleaning, cover all exposed surfaces with a light coating of oil.

Paste wax is recommended for table top.

WARNING: Never use highly volatile solvents. Non flamma-

ble solvents are recommended to avoid possible fire hazard.

ASSEMBLY

Refer to Figures 3-34.

CAUTION: Do not attempt assembly if parts are missing.

Use this manual to order replacement parts.

Be certain all parts are clean and free of shipping preserva-

tive. Also, completely remove all parts of packing. Saw cabinet

should be directly on the floor.

SAW INSTALLATION

Positioning the saw on a level surface will improve stability

and accuracy and prevent warpage and failure of cast

components and welds.

WARNING: Make certain that the saw is disconnected from

the power source.

INSTALL HANDWHEELS

Refer to Figure 3.

• Remove saw cabinet and place upside down on cardboard

box or cardboard on floor.

• Place one of the handwheels onto the blade raise/lower

shaft located on the front of the cabinet. Align the groove

in the back of the handwheel with the pin.

• Thread the washer and locking knob onto the threaded end

of the shaft.

• Repeat the steps above to assemble the remaining hand-

wheel and locking knob onto the blade tilt shaft located on

the side of the cabinet.

REMOVE PACKING MATERIAL

Refer to Figure 4.

• Use the blade tilt handwheel to tilt the motor completely to

45°.

• Remove the packing material from behind the motor.

• Return motor to the 0° position.

ASSEMBLE MOBILE BASE PANELS

Refer to Figures 5 and 6, pages 6 and 7.

Tools Required: 4mm Hex Wrench

Hardware Required: Twenty-four M6 x 12 socket pan head

bolts (Hardware bag #4).

• Attach the front panel between two corner supports using

six M6 x 12 socket pan head screws.

NOTE: Place the panel edges INSIDE the corner support

surfaces.

NOTE: Front panel and rear panel are both stamped ‘A’.

Front panel has warning label.

• Repeat above step for the rear panel.

• Turn all panels upside down to perform base assembly.

• Attach one corner of left panel (stamped ‘B’) to front panel

A.

• Attach the other corner of left panel B to rear panel A.

• Repeat above two steps for attachment of right panel

(stamped ‘C’).

Figure 3

Blade Raise Handwheel

Blade Tilt

Handwheel

Figure 4

Remove this

packing material

Figure 5

Letter Stamp On Top Edge

Below is completed base assembly.

ASSEMBLE CASTER SETS

Refer to Figures 7-11.

Tools Required: Two 1⁄2″Open End Wrenches

• Refer to Figure 7; remove casters (4) and supports (2)

from carton.

• Loosen and remove the bolt and hex nut from the bracket

(see Figure 8)

• Rotate foot pedal bar so that kick plate cam is inside

bracket (see Figure 9).

• The kick plate cam must be underneath the caster to func-

tion properly (see Figure 10).

• Refer to Figures 10 and 11; place caster onto the bracket

and secure in position with bolt and hex nut.

• Repeat above steps for the second caster set.

ATTACH CASTER SETS TO BASE

Refer to Figure 12.

Tools Required: 5mm Hex Wrench

Hardware Required: Eight M8 x 16 socket pan head screws

(Hardware bag #4).

• Attach one caster set to the two front corner supports

using four M8 x 16 socket pan head screws.

• Attach the remaining caster set to the two rear corner

supports.

7

Kick Plate Cam

Foot Pedal Bar

Bracket

Figure 7

Figure 8

Figure 9 - Kick Plate Cams Inside the Brackets

Figure 10

Figure 11

Figure 6

C

A

B

A

Figure 12

ATTACH CORD WRAP HOOKS

Refer to Figure 13.

Tools Required: 4mm Hex Wrench

Hardware Required: Two M6 x 16 socket pan head bolts, two

M6 flat washers and two M6 hex nuts (Hardware bag #4).

• Insert a bolt into a cord wrap hook and place against the

holes on the left side of the saw cabinet.

• Secure hook in position using flat washer and hex nut.

• Repeat for other hook.

ATTACH BASE TO CABINET

Refer to Figures 14 and 15.

Tools Required: 8mm Hex Wrench

Hardware Required: Four M10 x 25 socket head bolts, four M10

lock washers and four M10 flat washers (Hardware bag #4).

• Place dust chute over the cabinet as shown. Make sure

the holes in the corners are aligned with the slots in the

dust chute.

• Place the base assembly over the dust chute and secure

the base assembly to the cabinet using the flat washers,

lock washers and bolts.

• Secure all fasteners in the base assembly fully tight.

ATTACH RIP FENCE BRACKETS

Refer to Figure 16.

Tools Required: 5mm Hex Wrench

Hardware Required: Two M6 x 16 socket head bolts, two M6

flat washers and two M6 hex nuts (Hardware bag #4).

• Install the rip fence storage brackets to the right side panel

of the base using two bolts, flat washers and hex nuts.

BLADE GUARD AND PUSH STICK STORAGE

BRACKETS

Refer to Figure 17, page 9.

Tools Required: Phillips screwdriver and 4mm hex wrench

Hardware Required: Four M3 x 10 pan head screws, four M3

lock washers, four M3 flat washers, four M5 x 12 socket head

bolts, four M5 lock washers and four M5 flat washers

(Hardware bag #4).

• Install the push stick storage brackets to the left side panel

of the base using four screws, lock washers and flat

washers.

• Install the blade guard storage brackets to the left side

panel of the base using four screws, lock washers and flat

washers.

NOTE: Attach the slotted bracket to the front side of the saw.

• Press the four rubber feet to the base legs.

• With the aid of an assistant turn the saw upright.

WARNING: To avoid injury, Do Not attempt to turn saw

upright by yourself.

8

Figure 13

Figure 14

Figure 15

Figure 16

ATTACH EXTENSION TABLES

Refer to Figure 18.

Tools Required: 8mm Hex Wrench and Straight Edge

Hardware Required: Six M10 x 25 socket head bolts, six M10

lock washers and six M10 flat washers (Hardware bag #1).

• Assemble extension table to the table using socket head

bolts, lock washers and flat washers.

• Wipe surface clean.

• Hand tighten only. Do not tighten completely until tables

are level. Use a straightedge to level tables.

• Repeat above procedure for the other extension table.

• Use a straight edge to check level and flatness between

main and extension tables.

• After tables are adjusted level and flat, secure the exten-

sion tables by tightening the bolts completely.

INSTALL BLADE

Refer to Figures 19 and 20.

Tools Required: 13mm Open end Wrench

• Loosen knob on right side of cabinet.

• Remove blade and wrench. Replace knob.

• Raise blade assembly all the way up.

• Depress arbor lock and use wrench to loosen flange nut.

Remove flange and nut from arbor.

• Place blade on arbor. Make sure arrow on blade and teeth

point towards front of saw.

• Replace flange and nut on arbor and securely snug blade

in position.

CHECK TABLE ALIGNMENT

Refer to Figures 21, 22 and 23, page 10.

• Saws are shipped from the factory with the table adjusted

so the miter gauge slots are parallel to the saw blade.

However, in order to obtain the best results from the saw, it

is suggested this adjustment be checked before operating.

• A simple method of checking alignment is as follows: Bolt

or clamp a dowel rod or similar object to miter gauge (a

combination square can be substituted). Pick out a tooth

on front of blade and set the dowel to it so it is just touch-

ing. Move same tooth to back of blade.

• Gauge this tooth with the dowel rod. If the tooth is in the

same position, relative to the miter gauge slot, the table is

parallel with the blade. In short, the miter gauge slots must

be parallel with the blade. This means that when measur-

ing distance between blade and miter gauge slot at the

front and rear of the blade, the distances will be equal

(see Figure 21).

NOTE: Be sure to measure the distance or make the test

on the same tooth of the saw blade in both front and rear

positions.

9

Rubber Feet

Front Side of Saw

Slotted Bracket

Blade Guard

Bracket

Push Stick

Bracket

Figure 17

Figure 18

Straight Edge

Flange

Nut

Figure 19

Arbor Lock

Figure 20

• If an adjustment is necessary, proceed as follows: Loosen

and remove the six socket pan head screws and the rear

panel (see Figure 22). Loosen the four hex head bolts on

the trunnion (see Figure 23) and shift trunnions until a

position is found where the saw blade is parallel to the

miter guage slots.

NOTE: Saw blade should also be centered within its table

insert opening.

• Tighten the hex head bolts and lock washers very securely.

This procedure will set the table and blade in parallel posi-

tion and prevent the trunnion from shifting.

NOTE: If you perform this adjustment, leave the back panel off

to perform rear rail assembly as described in the next section.

RAIL ASSEMBLY

Refer to Figures 24-29.

Tools Required: 13mm Open end Wrench

Hardware Required: Eight M8 x 28 hex head bolts, eight M8 x

25 hex head bolts, four M8 x 20 hex head bolts, twenty M8

lock washers, twenty M8 flat washers, sixteen M8 hex nuts

and four M8 acorn nuts. (Hardware bag #2).

• Insert two M8 x 28 hex head bolts and two M8 x 25 hex

head bolts into the T-slot of the right front guide rail. (The

two longer bolts will attach to the table; the two shorter

bolts attach to the table extension.)

• Attach right front rail to the table and right table extension

using flat washers, lock washers and hex nuts.

NOTE: Hand tighten all hardware during rail assembly. Do not

completely tighten hardware until all rails are mounted.

• Attach left front rail in the same manner. (The two longer

bolts attach to the table; the two shorter bolts attach to

table extension.)

NOTE: You may have to shift right rail as far right as it will go

to attach left rail.

• Position rails so that rails are butted together and the joint

between rails is aligned with right side of the blade. You

may need a mallet to lightly tap rails together. Make sure

rails are completely butted together at the joint.

• Use a straight edge as shown to check level and flatness

between right and left rail. Use a combination square as

shown to make certain that both front rails are parallel to

the table surface.

• After front rails are adjusted level and flat, tighten the

screws completely.

• Secure all hardware completely.

10

Figure 21 - Aligning Miter Slots to Blade

Equal

Distances

Saw

Blade

Rear

Miter Gauge Slots

Front

M8 x 28 Bolts M8 x 25 Bolts

Figure 24 - Right Front Rail

Figure 25 - Use Straight Edge to Align Rail Joint to Blade

Figure 22 - Remove Rear Panel

Figure 23 - Adjust Trunnions to Align Blade and Miter Slot

Remove Six Screws

• Loosen and remove six socket pan head screws and the

back panel. This will allow easier attachment of the rear rails.

• Install the rear rails in the same manner as the front rails

and align the rail joint to the blade.

• Replace back panel of the cabinet.

• Insert M8 x 20 hex bolts through holes in bracket at each

end of brace. Attach brace to the far right end of the rails

by sliding hex bolts into the rail T-slots. Secure bolts in

position with flat washers, lock washers and nuts.

ATTACH SWITCH ASSEMBLY

Refer to Figure 30.

Tools Required: 10mm Open end Wrench

Hardware Required: Two M6 x 16 hex head bolts, two M6 flat

washers, two M6 lock washers and two M6 hex nuts.

(Hardware bag #3).

• From above switch assembly bracket, insert two bolts

through bracket holes.

• Loosely attach flat washer, lock washer and nut to bolts.

• Insert bolt heads into T-slot on bottom of left front rail.

• Slide switch assembly 6″to 8″from left end of rail as

shown in Figure 30.

• Fully tighten flat washers, lock washers and hex nuts to

secure switch assembly in place.

POSITION AND ADJUST RIVING KNIFE

Refer to Figure 31.

• Riving knife is installed on the saw. Raise the blade com-

pletely to access the riving knife.

• Loosen the locking knob and raise the riving knife to its

highest position. Riving knife has three holes for three posi-

tions. The highest position is for all thru cuts. The middle

position is for rabbets and other non-thru cuts, (with guard

and pawls removed). The lowest position is for dado cuts.

11

Figure 26 - Check parallelism of rails to table with combination

square. Check at several locations along rail.

Figure 27

Figure 28

Figure 29

Figure 30

Figure 31 - Riving Knife

Locking Pin

Bracket

Plate

Locking

Knob

Screw

• Make sure locking pin is aligned with riving knife hole and

secure in position by tightening locking knob.

• Riving knife must be in line with blade. Make sure riving

knife sits flat against mounting bracket and lock plate.

RIVING KNIFE TO BLADE ADJUSTMENT

• Riving knife to blade clearance: the gap between the riving

knife and the saw blade should be an even distance

across the entire radius.

• The riving knife should also be in line with the saw blade. If

adjustment is necessary:

1. Locate the riving knife bracket.

2. Loosen the two socket head cap screws slightly enough

to move the bracket, bringing the riving knife in line with

the saw blade. Make sure the gap between the blade

and knife is even and from 1⁄4to 5⁄16″in distance.

3. Once the riving knife is aligned with the blade, tighten

the socket head cap screws.

INSTALL TABLE INSERT

Refer to Figure 32.

• Make sure that the riving knife is raised to its highest

position.

• Place table insert into throat of table.

• Insert is held in position by magnet in table.

• To adjust insert level with table, adjust leveling screws up

or down.

ATTACH BLADE GUARD AND ANTI-KICKBACK

PAWLS

Refer to Figures 33-36, page 12 and 13.

• Place the slot of blade guard body over the riving knife.

Slot of bushing is placed in the notch indicated in Figures

33 and 34.

• The bushings have a beveled edge and must be located in

the center of the notch to lock properly.

• Position guard completely down on riving knife and press

latch to lock in position.

• Blade guard body should be parallel to the table. If not,

adjust the 2mm set screws as necessary.

• Place anti-kickback pawl set onto riving knife at notches

indicated. The spring pin is placed in the front notch and

bolt is placed in the rear notch.

• Press pawl set completely down and press latch to secure

in position.

NOTE: The teeth of anti-kickback pawls should touch table

surface. Use set screws to adjust if needed.

12

Figure 32

Leveling Screws

Figure 33 - Blade Guard and Pawl Attachment

Blade Guard Pawl Set

Riving Knife

Figure 34

Bushing

Notch

Figure 35 - Attach Pawl Assembly

Pin

Bolt

Insert Pin Here

Insert Bolt Here

13

INSTALL MITER GAUGE

Refer to Figure 37.

• The miter gauge comes preassembled. Unpack the miter

gauge and clean thoroughly. Insert into storage slots on

right side of cabinet.

INSTALL PUSH STICK

Refer to Figure 38.

• Insert the push stick into brackets on left side of base.

INSTALL RIP FENCE

Refer to Figure 39.

• Position rip fence assembly at end of saw. Be certain lock-

ing lever is in UP unlocked position.

• Place rip fence assembly onto rails, positioning clamp over

rear rail and then placing rip fence onto front guide rail.

• Rip fence should now ride freely on rip fence rails. Once

rip fence is completely installed, it should be parallel with

the miter gauge and perpendicular to the table. If not, refer

to “Rip Fence Adjustment” in the Operation section of this

manual.

INSTALLATION

GROUNDING INSTRUCTIONS

WARNING: Improper connection of equipment grounding con-

ductor can result in the risk of electrical shock. Equipment should

be grounded while in use to protect operator from electrical shock.

• Check with a qualified electrician if grounding instructions

are not understood or if in doubt as to whether the tool is

properly grounded.

• This tool is equipped with an approved 3-conductor cord

rated at 300V and a 3-prong grounding type plug (see Figure

40) for your protection against shock hazards.

• Grounding plug should be plugged directly into a properly

installed and grounded 3- prong grounding-type receptacle,

as shown (Figure 40).

• Do not remove or alter grounding prong in any manner. In

the event of a malfunction or breakdown, grounding pro-

vides a path of least resistance for electrical shock.

WARNING: Do not permit fingers to touch the terminals of

plug when installing or removing from outlet.

• Plug must be plugged into matching outlet that is properly

installed and grounded in accordance with all local codes and

ordinances. Do not modify plug provided. If it will not fit in

outlet, have proper outlet installed by a qualified electrician.

Figure 36 - Latches Lock and Unlock Blade Guard and Pawls

to Riving knife

Set Screws

Latches

Figure 37

Figure 38

Figure 39

Figure 40 - 3-Prong Receptacle

Grounding Prong

3-Prong Plug

Properly Grounded Outlet

• Inspect tool cords periodically and if damaged, have them

repaired by an authorized service facility.

• Green (or green and yellow) conductor in cord is the

grounding wire. If repair or replacement of the electric cord

or plug is necessary, do not connect the green (or green

and yellow) wire to a live terminal.

• Where a 2-prong wall receptacle is encountered, it must be

replaced with a properly grounded 3-prong receptacle

installed in accordance with National Electric Code and

local codes and ordinances.

WARNING: This work should be performed by a qualified

electrician.

A temporary 3-prong to 2-prong grounding adapter (see

Figure 41) is available for connecting plugs to a two pole out-

let if it is properly grounded.

• Do not use a 3-prong to 2-prong grounding adapter unless

permitted by local and national codes and ordinances.

• (A 3-prong to 2-prong grounding adapter is not permitted

in Canada.) Where permitted, the rigid green tab or termi-

nal on the side of the adapter must be securely connected

to a permanent electrical ground such as a properly

grounded water pipe, a properly grounded outlet box or a

properly grounded wire system.

• Many cover plate screws, water pipes and outlet boxes are

not properly grounded. To ensure proper ground, grounding

means must be tested by a qualified electrician.

EXTENSION CORDS

• The use of any extension cord will cause some drop in

voltage and loss of power.

• Wires of the extension cord must be of sufficient size to

carry the current and maintain adequate voltage.

• Use the table to determine the minimum wire size (A.W.G.)

extension cord.

• Use only 3-wire extension cords having 3-prong grounding

type plugs and 3-pole receptacles which accept the tool plug.

• If the extension cord is worn, cut, or damaged in any way,

replace it immediately.

Extension Cord Length (120V Operation)

Wire Size A.W.G.

Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Up to 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

NOTE: Using extension cords over 50 ft. long is not

recommended.

ELECTRICAL CONNECTIONS

WARNING: Make sure unit is off and disconnected from

power source before inspecting any wiring.

The saw is prewired for use on a 120 volt, 60HZ power supply.

The power lines are inserted directly onto the switch. The

green ground line must remain securely fastened to the frame

to properly protect against electrical shock.

240 VOLT OPERATION

• To use the saw with a 240V, single-phase power supply,

have a qualified electrician attach a 240 volt, 15A 3-prong

plug onto saw line cord and install the proper connectors

and receptacles to power supply.

• See wiring diagram (Figure 42) for wiring instructions.

OPERATION

Refer to Figures 43-52, pages 15-18.

DESCRIPTION

The Craftsman 10″Model Number 218330 contractor saw

offers precise cutting performance for all woods up to 31⁄8″

thick. The saw is designed for the professional user and is

ruggedly constructed for continuous service. The 10″Saw is

recommended for use with a 10″blade.

The saw features an extra large cast iron table. Saw body has

on board storage for push stick, miter gauge, rip fence and

saw blades. Saw is equipped with a riving knife and a clear

acrylic blade guard with anti-kickback feature. Cabinet is con-

structed of heavy gauge welded steel, totally enclosed and is

ported for a 4″vacuum hose.

Rip Fence Assembly features a heavy-duty precision rip fence

that is designed for simple and one-hand maneuverability.

Front rail is calibrated in inches and millimeters with a magni-

fied window for close tolerances.

SPECIFICATIONS

Capacity with 10″Blade:

Depth of cut at 90°. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31⁄8″

Maximum tilt angle of arbor (left) . . . . . . . . . . . . . . . . . . . . 45°

Depth of cut at 45° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23⁄16″

Max. cut right of blade with rip fence . . . . . . . . . . . . . . . . . 30″

Max. cut left of blade with rip fence . . . . . . . . . . . . . . . . . . 13″

Saw Dimensions:

Table height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373⁄8″

Cabinet depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22″

Cabinet width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19½″

Table area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265⁄16 x 203⁄16″

Front of table to blade . . . . . . . . . . . . . . . . . . . . . . . . . . . 113⁄4″

14

Figure 42 - Wiring Schematic

3

3

1

120V

240V

1

2

4

2

4

L1 L2

L1 L2

Figure 41 - 2-Prong Receptacle with Adapter

Make Sure

This Is

Connected To

A Known

Ground

2-Prong Receptacle

Grounding Lug

Adapter

3-Prong Plug

Rip Fence Dimensions:

Rip fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311⁄4″

Rip fence rails (front and rear) . . . . . . . . . . . . . . . . . . . . . 561⁄2″

Blade capacity maximum . . . . . . . . . . . . . . . . . . . . . . . . . . 10″

Blade arbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5⁄8″

Dado blade capacity maximum . . . . . . . . . . . . . . . . . . . . . 13⁄16″

Saw Constructions:

Cabinet . . . . . . . . . . . . . . . . . . . . Totally enclosed steel panel

Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cast iron

Rip fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum tube

Drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V-belt

Exhaust port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4″Male

Miter gauge . . . . . . . . . . . . . . Cast iron with T-slot roller guide

Blade guard . . . . . . . . . . . . . . Acrylic with anti-kickback pawls

Switch. . . . . . . . . . . . . . . Locking paddle switch with overload

Arbor R.P.M.. . . . . . . . . . . . . . . . . . . . . . . . 3450 RPM approx.

Motor: . . . . . . . . . . . . . . . . . 13⁄4HP, 3550 RPM, capacitor start,

capacitor run, 120/240V, 15/7.5A,

single-phase, ball bearing

Gross weight with motor . . . . . . . . . . . . . . . . . . . . . . . 288 lbs

WARNING: Disconnect power before attempting any of the

following procedures. Be certain switch is in OFF position and

safety disconnect (or breaker) is in OFF or open position. Saw

blade must not be moving. Saw blade will rotate freely after

motor is turned off. Allow blade to come to a complete stop

before attempting any of the following procedures.

WARNING: The operation of any power tool can result in

foreign objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety goggles complying

with United States ANSI Z87.1 before commencing power tool

operation.

STARTING AND STOPPING THE SAW

Refer to Figure 43.

WARNING: Never operate saw without blade guards in

place. Be sure blade is not in contact with workpiece when

motor is started. Start motor and allow saw to come to full

speed.

WARNING: Make sure the electrical characteristics of motor

nameplate and power source are the same.

• The ON/OFF switch is located under the front rail of the

table saw at the left side.

• To turn saw on, stand to either side of the blade—never in

line with it. Raise large red OFF paddle and pull up

ON/OFF switch. Always allow saw blade to come up to full

speed before cutting.

• Do not turn motor switch ON and OFF rapidly. This action

overheats the motor and may cause saw blade to loosen.

• Never leave saw while the power is on.

• To turn the table saw off, press the large red OFF paddle.

Never leave saw until cutting tool has come to a complete

stop.

The saw can be locked from unauthorized use by locking the

switch. To lock the switch:

• Turn the switch to OFF position and disconnect saw from

power source.

• Pull the key out. The switch cannot be turned on with the

key removed.

NOTE: Should the key be removed from the switch at the ON

position, the switch can be turned off but cannot be turned on

again.

• To replace key, slide key into the slot on switch until it

snaps.

WARNING: For your own safety, lower blade or cutting tool

below table surface. If blade is tilted, return it to vertical posi-

tion. Turn off safety disconnect or circuit breaker when saw is

not in use.

BLADE HEIGHT ADJUSTMENT

Refer to Figure 44.

• Blade height is controlled by handwheel on the front of the

saw.

• To adjust height, loosen locking hand knob. Rotate knob

counterclockwise approximately three turns. Turn hand-

wheel to desired blade height.

CAUTION: For safety, blade should be raised only 1/8″above

the surface of the material to be cut. However, if hollow

ground blades are used, raise blade to its maximum height to

allow for greater blade clearance.

• Lock blade height into position. Lock handwheel by tight-

ening locking knob clockwise. Tighten only until snug.

IMPORTANT: Do not over tighten. Only a small amount of

pressure is necessary to lock handwheel securely.

BLADE TILT ADJUSTMENT

Refer to Figures 44 and 45, page 15 and 16.

• The saw blade can be set at any angle between 90° and

45°. Blade tilt is controlled by the handwheel (Fig. 44) on

the right side of the saw. The indicator (Fig. 45) on front of

saw shows the tilt angle of the blade.

• To adjust tilt, loosen locking hand knob. Rotate knob coun-

terclockwise at least three turns. Turn handwheel to

desired blade angle. Lock blade angle into position.

15

Figure 43 - ON/OFF Switch

Paddle

Switch

Key

Figure 44 - Blade Height Adjustment

Angle

Indicator Lock Knob

Handwheel

• Lock handwheel by tightening locking hand knob clock-

wise. Tighten only until snug.

• The saw is equipped with positive stops at 90° and 45°.

These positive stops allow operator to position saw blade

at 90° and 45° quickly and accurately.

90° STOP ADJUSTMENT

Refer to Figures 44 and 46.

• Raise saw blade above table as far as possible. Set blade

at 90° to table by turning the tilting handwheel. Place a

square on table and check to see if blade is perpendicular

to the table. When checking put square flush against saw

blade. Do not put square on teeth of saw blade.

• If the blade will not tilt to 90°, turn (counterclockwise) the

set screw at the left front of the table insert until the blade

can be positioned to 90°.

• Once the blade has been tilted to 90° (confirm this using

your square), tighten the bevel handwheel lock knob,

located on the side of the cabinet. This will keep the blade

from tilting further.

• Turn the set screw (clockwise) until it comes in contact

with the positive stop.

• Check tilt indicator pointer. If necessary, adjust pointer so it

points to 0° mark on scale. To adjust pointer, remove

handwheel and loosen screw on pointer. Be sure to tight-

en screw securely after adjustment is completed.

45° STOP ADJUSTMENT

Refer to Figure 46.

• Tilt the saw blade to 45°. Using a combination square,

check to see if blade is 45° to the table.

• If the blade will not tilt to 45°, turn (counterclockwise) the

set screw located at the right of the table insert, until the

blade can be positioned to 45°.

• With the blade at 45°, tighten the bevel handwheel lock

knob to keep the blade from further tilting.

• Turn the set screw clockwise until it comes in contact with

the positive stop.

TABLE INSERT ADJUSTMENT

Refer to Figure 46.

• The table insert must always be level with the saw table.

• Place a straight edge across the front and rear of the table

insert. Check that the insert is perfectly level with the saw

table.

• To level the table insert, turn one or more adjusting set

screws as needed and recheck.

• The table insert is equipped with two finger holes for easy

removal.

MITER GAUGE ADJUSTMENT

Refer to Figures 47 and 48, Pages 16 and 17.

• Miter gauge supplied with saw is equipped with individually

adjustable index stops at 0° and 45°, right and left, and

can be manually adjusted up to 60° right and left.

Adjustment to index stops can be made by loosening lock-

ing nut and tightening or loosening three adjusting screws.

Be sure to tighten locking nut after adjustment is made.

• Face of miter gauge has two holes for purpose of attach-

ing auxiliary facing.

• Miter gauge is accurately constructed for precision work.

Miter gauge is guided through T-slot with a roller guide

mounted at front of guide bar. Roller guide adds to miter

gauge's stability and prevents the guide bar from leaving

T-slot.

• To operate miter gauge, simply loosen locking knob and

move miter gauge to desired angle. The miter gauge will

stop at 0° and 45°, both right and left. To position miter

gauge past these points, simply pull out gauge stop.

Position miter gauge at desired angle and tighten locking

knob.

• Be positive the edge of workpiece next to face of miter

gauge is straight and tight against miter gauge so that the

workpiece does not rock or rotate. Always use both hands

when operating the miter gauge.

• The miter gauge is used for cross-cutting, compound miter

cutting, miter cutting, rabbeting, bevel cutting and dadoing.

16

Figure 45 - Blade Tilt Handwheel

Lock Knob

Blade Tilt

Handwheel

Figure 46 - Table Insert

Level

Adjusting

Screws

90° Stop

Adjustment

45° Stop

Adjustment

Figure 47 - Index Stops

Index Stop Adjusting Screws and Nuts

RIP FENCE ADJUSTMENT

The saw's rip fence is precision manufactured, incorporating

fine adjustments for accurate cuts. The saw is built to allow

the operator to accurately adjust the rip fence without prob-

lems in a matter of seconds.

LEVELING THE FENCE TO THE TABLE

• Lift the lock handle to unlock the fence.

• Observe the space between the fence bottom and the

table. The space should be equal along the entire length

of the fence.

• If the space is not equal, the rails need to be adjusted so

that rails are at the same vertical position with respect to

the table. See Rail Assembly, pages 10-11.

SETTING CLAMPING PRESSURE

Refer to Figure 49.

Rip fence has been adjusted at the factory to lock securely

when the lock handle is pushed down. To adjust:

• Unlock fence and remove it from the rails.

• Adjust the hex nut until the fence is held securely when

the lock handle is pushed down,

SETTING FENCE PERPENDICULAR AND PARALLEL

Refer to Figure 50.

PERPENDICULAR ADJUSTMENT

• Position fence anywhere on table and lock it down.

• Place a square on the table next to the fence and check to

see that the fence is at 90° to the table.

• If an adjustment is necessary, unlock the fence and turn

either of the two adjusting screws.

NOTE: This is for micro-adjustment only. If fence cannot be

adjusted square, recheck rail adjustment.

• Lock fence in position and recheck. Continue this proce-

dure until fence is square to the table.

PARALLEL ADJUSTMENT

• Position fence so that fence edge is aligned with slot edge.

• Slot and fence edge should be parallel.

• If an adjustment is necessary, unlock the fence and turn

either of the two adjusting screws.

• Lock fence in position and recheck. Continue this proce-

dure until fence is square to the table.

CURSOR ADJUSTMENT

Refer to Figure 51.

• Raise the saw blade above the table.

• Position the fence several inches to the right of the saw

blade.

• Lock the fence down and measure the exact distance

between the saw blade and the inside of the fence.

• Loosen the two screws on the lens and slide it left or right

until the cursor (red line) equals the measurement

obtained in the previous step.

• Retighten the screws and make a test cut. Measure the

cut piece to verify that the cursor is set correctly.

NOTE: This adjustment should be checked whenever a new

blade is installed.

17

Figure 48 - Miter Gauge Assembly

Locking Knob

Roller Guide

Miter Gauge

Gauge Stop

Figure 50

Perpendicular Adjustment

Parallel Adjustment

Figure 51

Cursor Adjustment Screws

Locking Lever

Figure 49 - Nut to Adjust Clamping Pressure

Hex Nut

RIP FENCE OPERATION

Refer to Figure 51.

• Unlock the fence by lifting the locking lever. Using the

scale for placement, position the rip fence. Lock the rip

fence into position by placing the locking lever in the down

position.

• The rip fence is used for the following operations: ripping,

bevel ripping, ploughing, resawing, rabbeting and dadoing.

INSTALLING AND REMOVING THE RIVING KNIFE

Refer to Figure 52.

Install

• Line up the riving knife in the proper direction to the

mounting bracket.

• Push the riving knife all the way down into the mounting

bracket. Make sure the lock pin is locked in the hole of the

riving knife. (The lock hole is on the button side of the

riving knife).

• If the riving knife is not locked properly, hold the locking

knob and pull the lock pin out; then re-insert the pin secure-

ly in the hole of the riving knife. While raising or lowering the

knife, pin will snap in the hole of the knife when located at

one of the three positions.

• Tighten the locking knob.

Remove

• Loosen the locking knob.

• Hold the knob and pull the locking pin out.

• Remove the riving knife out of the mounting bracket.

NOTE: Make sure blade is at the highest position before

adding or removing the riving knife.

WARNING: For your own safety, always observe the follow-

ing safety precautions.

• Never make any cut freehand (without using miter gauge

or rip fence). Blade can bind in the cut and cause a kick-

back.

• Always lock miter gauge or rip fence securely when in use.

• Remove rip fence from the table when miter gauge is in

use.

• Remove miter gauge from table when rip fence is in use.

• Make sure blade guard is installed for all “through sawing”

operations. Through sawing operations are those opera-

tions in which the saw blade cuts completely through the

thickness of the wood. Replace guard immediately after

completion of resawing, rabbeting and dadoing.

Frequently check action of anti-kickback pawls by passing

the workpiece alongside the spreader while saw is off. Pull

the workpiece toward you. If the pawls do not dig into the

workpiece and hold it, the pawls must be sharpened. (See

Maintenance section, page 19.)

• Have blade extend approximately 1/8″above top of work-

piece. Additional blade exposure increases hazard

potential.

• Do not stand directly in front of blade in case of a kick-

back. Stand to either side of the blade.

• Keep your hands clear of the blade and out of the path of

the blade.

• If the blade stalls or stops while cutting, turn switch OFF

and safety disconnect OFF before attempting to free the

blade.

• Do not reach over or behind the blade to pull the work-

piece through the cut, to support long or heavy work-

pieces, to remove small cut-off pieces of material or for

any other reason.

• Do not pick up small pieces of cut-off material from the

table. Remove them by pushing them off table with a long

stick. Otherwise they could be thrown back at you by the

rear of the blade.

• Do not remove small pieces of cut-off material that may

become trapped inside blade guard while saw is on. This

could endanger your hands or cause a kickback. Turn saw

off. After blade has stopped turning, lift guard and remove

the piece.

• Always lower blade below the table level when machine is

not in use.

TYPES OF CUTS/OPERATIONS

CROSSCUTTING

WARNING: Use caution when starting the cut to prevent

binding of the guard against the workpiece.

This cut is performed with the miter gauge set at “0”, and is

used for cutting across the workpiece grain at 90° (blade

square with both the edge and flat side of wood).

MITER CUTTING

WARNING: Miter angles greater than 45˚ may force the

blade guard assembly into the saw blade causing damage to

the blade guard assembly and personal injury. Before starting

the motor, test the operation by feeding the workpiece into the

blade guard assembly. If the blade guard assembly contacts

the blade, place the workpiece under the blade guard assem-

bly, not touching the blade, before starting the motor.

WARNING: Certain workpiece shapes, such as molding may

not lift the blade guard assembly properly. With the power off,

feed the workpiece slowly into the blade guard area and until

the workpiece touches the blade. If the blade guard assembly

contacts the blade, place the workpiece under the blade

guard assembly, not touching the blade, before starting the

motor.

This cut is performed with the miter gauge, and is used for

cutting at an angle other than 90° square with the edge of the

workpiece.

BEVEL CROSSCUTTING

WARNING: When possible, use the right miter gauge slot

when bevel crosscutting so that the blade tilts away from the

miter gauge and your hands.

WARNING: Use caution when starting the cut to prevent

binding of the guard against the workpiece.

This cut is performed with the miter gauge, and is the same

as crosscutting, except that the workpiece is also cut at an

angle other than 90° square to the flat side of the wood (blade

is at an angle).

18

Figure 52 - Riving Knife

Locking Pin

Bracket

Plate

Locking

Knob

Screw

COMPOUND MITER CUTTING

This cut is performed with the miter gauge, and is a combina-

tion of miter cutting and bevel crosscutting. The cut is made at

angle other than 90° to both the edge and flat side of wood.

RIPPING

WARNING: When bevel ripping and whenever possible,

place the fence on the side of the blade so that the blade is

tilted away from the fence and hands. Keep hands clear of the

blade and use a push stick to feed the workpiece if there is

less than 6″between the fence and the blade.

This cut is performed with the rip fence, and is used to cut the

workpiece lengthwise with the grain. Position the fence to the

desired width of rip and lock in place. When ripping long

boards or large panels, always use a work support.

BEVEL RIPPING

WARNING: Before connecting the table saw to the power

source or operating the saw, always inspect the blade guard

assembly and riving knife for proper alignment and clearance

with saw blade. Check alignment after each change of bevel

angle.

WARNING: When possible, place the fence on the right side

of the blade so that the blade is tilted away from the fence

and hands. Keep your hands clear of the blade and use a

pushstick to feed the workpiece if there is less than 6″

between the fence and the blade.

This cut is performed with the rip fence, and is the same as

ripping, except that the blade is set at an angle other than 90°.

RESAWING

This cut is performed with the rip fence, and is used to rip a

workpiece through its thickness rather than across its flat

width. Do not attempt to resaw bowed or warped material.

NOTE: It may be necessary to remove blade guard and use

work supports as well as push blocks when performing this

operation.

WARNING: Install blade guard immediately upon completion

of resawing operation.

PLOUGHING

This cut is performed with the rip fence, and is used to make

a groove lengthwise with the grain of the workpiece. Use

proper hold downs and feed devices.

RABBETING

This cut is performed with either the miter gauge or rip fence.

Rabbeting is used to cut out a section of the corner of a

workpiece, across an end or along an edge. To make a rabbet

requires cuts which do not go all the way through the materi-

al. Therefore, blade guard must be removed. Install blade

guard immediately upon completion of rabbeting operation.

Rabbet cuts can also be made using dado head.

DADOING

This cut is performed with either the miter gauge or rip fence.

Dadoing is done with a set of blades (dado set) rather than

standard saw blades. The dado set is used to groove wood

similar to ploughing and rabbeting. However, the dado set

allows operator to remove more material in one pass. The

operator, with a dado set, can vary width of cut up to 13⁄16″.

Instructions for operating dado set are contained in owner’s

manual furnished with dado set. Dadoing requires cuts which

do not go all the way through material. Therefore, blade guard

must be removed. Dado sets have different characteristics

than saw blades. As a result, saw must be fitted with special

parts that are furnished with saw (Dado Insert, Part No.

31158.00).

When using a dado set, the following parts must be substitut-

ed dado table insert (not included).

IMPORTANT: Always use correct insert. When using the

dado set, use caution. Use featherboards and push sticks as

applicable.

WARNING: Always immediately replace the standard blade,

blade guard and blade insert when you are finished dadoing.

FREEHAND

Freehand is a very dangerous operation of making a cut with-

out using the miter gauge or rip fence. Freehand cuts must

never be performed on a Table Saw.

CUTTING OVERSIZED WORKPIECES

When cutting long workpieces or large panels, always support

workpiece that is not on table. Use adjustable roller stand or

make simple support by clamping a piece of plywood to saw

horse. Add facings to miter gauge or rip fence as needed.

IMPORTANT: Do not allow facings to interfere with operation

of blade guard.

DUST COLLECTING

• Saw is fitted with a 4″male exhaust port.

• Before starting saw, see that all adjustments are properly

made and guards in place. With power disconnected, turn

pulley by hand to make sure everything is correct before

connecting power and starting saw.

BLADE SELECTION

Blade selection is based on type of material being cut and

how it will be cut. There are three general types of saw

blades: rip saw blades cut with grain of wood, cut-off saw

blades cut across grain, and combination saw blades cut with

grain, across grain and any angle to grain.

Blades vary in many aspects. When selecting a blade, the fol-

lowing blade characteristics should match up with operation to

be performed and type of material to be cut: type of steel;

quality of steel; tooth style; tooth set; carbide tipped; grind;

number of teeth and size.

IMPORTANT: Your saw is only as accurate and efficient as

blade or cutting tool used.

First, be certain to use the appropriate type of cutting tool for

the operation to be performed. Second, it is strongly recom-

mended that high-quality blades and cutting tools be used. Be

certain blades and cutting tools are kept sharp and in good

working order. Check blades periodically and replace or

sharpen if necessary.

MAINTENANCE

WARNING: Do not attempt under any circumstances, to

service, repair, dismantle, or disassemble any mechanical

or electrical components without physically disconnecting all

power sources.

CLEANING

• Clean off any preservative on bright (machined ) parts with

appropriate solvent (mineral spirits). Avoid getting cleaning

fluid on any rubber parts as they tend to deteriorate

rubber.

19

• Use soap and soft water on rubber and plastic parts.

• After cleaning, lubricate unpainted surfaces with a light

application of medium consistency machine oil. This lubri-

cation should be repeated at least once every six months.

NOTE: Instead of oil, a good quality paste wax can be applied

to rip fence and table surface. Paste wax will enhance move-

ment of workpieces. In addition to providing lubrication, paste

wax will help prevent rusting.

• Keep your machine and your workshop clean. Do not allow

sawdust to accumulate on saw or inside cabinet.

Frequently vacuum or blow out any sawdust that may

accumulate within cabinet.

• Be certain motor and internal mechanisms are clean and

are frequently vacuumed or blown free of any dirt.

LUBRICATION

All bearings on the arbor are shielded ball bearings. These

bearings are permanently lubricated at the factory.

• As needed, clean the grease off the rack and worm gears

of height and tilt mechanism. Lubricate rack and gears

with a medium viscosity machine oil.

• Be sure to lubricate trunnion ways and all bushings.

• Occasionally oil all other bearing points, including blade

guard assembly, miter gauge and rip fence.

SERVICE

• Replace belts and worn parts as needed. If power cords

are worn, cut, or damaged in any way, have them

replaced immediately.

• Make sure teeth of anti-kickback pawls are always sharp.

• Sharpen dull teeth using a few light strokes of a smooth

cut flat file.

CHANGING THE SAW BLADE

Refer to Figures 53 and 54.

WARNING: Turn the power switch “OFF” and unplug the

power cord from its power source when changing the saw blade.

WARNING: When replacing blades, check the thickness

stamped onto the riving knife. You must select a blade with a

kerf width larger than the thickness of the riving knife. Thinner

blades may cause the workpiece to bind during cutting.

WARNING: USE ONLY 10″diameter blades with 5⁄8″arbor

holes, rated at or higher than 3800 R.P.M.

• Remove blade guard assembly and pawl assembly.

• Remove the table insert.

• Unlock the raise/lower handwheel lock and raise saw

blade to maximum height.

• Depress locking pin (see Figure 53) and slowly rotate

blade toward you until pin engages into arbor. Hold arbor

in locked position.

• Place supplied open-end wrench (A) on the arbor nut (B).

Turn wrench counterclockwise to loosen nut. Remove

arbor nut, blade flange (C) and saw blade (D).

• Place new blade on arbor. Make sure saw blade teeth

point down at the front side of saw table. Place flange and

nut on arbor and securely snug blade in position.

• Replace table insert.

• Replace blade guard assembly and pawl assembly.

Repair Protection Agreements

Congratulations on making a smart purchase. Your new

Craftsman®product is designed and manufactured for years

of dependable operation. But like all products, it may require

repair from time to time. That’s when having a Repair

Protection Agreement can save you money and aggravation.

Here’s what the Repair Protection Agreement*

includes:

!Expert service by our 10,000 professional repair special-

ists

!Unlimited service and no charge for parts and labor on

all covered repairs

!Product replacement up to $1500 if your covered prod-

uct can’t be fixed

!Discount of 10% from regular price of service and related

installed parts not covered by the agreement; also, 10% off

regular price of preventive maintenance check

!Fast help by phone – we call it Rapid Resolution –

phone support from a Sears representative. Think of us as

a “talking owner’s manual.”

Once you purchase the Repair Protection Agreement, a sim-

ple phone call is all that it takes for you to schedule service.

You can call anytime day or night, or schedule a service

appointment online.

The Repair Protection Agreement is a risk-free purchase. If you

cancel for any reason during the product warranty period, we

will provide a full refund. Or, a prorated refund anytime after

the product warranty period expires. Purchase your Repair

Protection Agreement today!

Some limitations and exclusions apply. For prices and

additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full

details call Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major home

items, in the U.S.A. or Canada call 1-800-4-MY-HOME®.

20

Figure 53 - Locking Pin Engages Arbor to Lock in Position

Locking Pin

Figure 54

A

B

C

D

21

Service Record

Craftsman 10″Contractor Table Saw

DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED

22

TROUBLESHOOTING

SYMPTOM

Saw stops or will not start

Excessive vibration

Cannot make square cut

when crosscutting

Blade stalls (however, motor turns)

Blade does not come up to speed

Cut binds, burns or stalls when ripping

Cut not true at 45 or 90° positions

Tilt and elevating handwheel

difficult to turn

Rip fence binds on guide tube

Frequent opening of fuses or

circuit breakers

Material kicked back from blade

POSSIBLE CAUSE(S)

1. Overload tripped

2. Saw unplugged from wall or motor

3. Fuse blown or circuit breaker tripped

4. Cord damaged

5. Defective capacitor

1. Stand on uneven floor

2. Damaged saw blade

3. Bad drive V-belts

4. Bent pulley

5. Improper motor mounting

6. Loose hardware

7. Loose set screw in pulley

Miter gauge not adjusted properly

1. Drive belts not tight

2. Drive belts worn

1. Extension cord too light or too long

2. Low shop voltage

3. Motor not wired for correct voltage

1. Dull blade with improper tooth set

2. Blade is binding at one end of cut

(heeling)

3. Warped board

4. Rip fence not parallel to blade

5. Riving knife out of alignment

6. Excessive feed rate

Positive stops not properly adjusted

1. Sawdust on rack and worm gears

2. Bushings and bearing surfaces dirty

1. Guide rails or extension wing not

properly installed

2. Guide of rip fence not adjusted

properly

1. Motor overloaded

2. Fuses or circuit breakers do not have

sufficient capacity

1. Rip fence out of alignment

2. Riving knife not aligned with blade

3. Feeding stock without rip fence

4. Riving knife not in place

5. Dull blade

6. Letting go of material before it is past

blade

7. Anti-kickback fingers dull

CORRECTIVE ACTION

1. Allow motor to cool and reset by

pushing reset switch

2. Check all plug connections

3. Replace fuse or reset circuit breaker

4. Replace cord

5. Replace capacitor

1. Reposition on flat, level surface

2. Replace saw blade

3. Replace drive V-belts

4. Replace pulley

5. Check and adjust motor

6. Tighten hardware

7. Tighten set screw

Adjust miter gauge

1. Adjust drive belt tension

2. Replace drive belts

1. Replace with adequate size cord

2. Contact your local electric company

3. Refer to motor junction box

1. Sharpen or replace blade

2. Adjust table and rip fence

parallel to blade

3. Make sure concave or hollow side is

facing down; feed slowly

4. Adjust rip fence

5. Adjust riving knife to fall in line with

blade

6. Reduce feed rate

Adjust blade tilt

1. Clean and relubricate

2. Clean thoroughly and lubricate

1. Reassemble guide rails

2. Adjust guides

1. Feed work slower into blade

2. Install proper size fuses or circuit

breakers

1. Align rip fence with miter slot

2. Align riving knife with blade

3. Always use rip fence or miter gauge

4. Install riving knife

5. Replace blade

6. Push material all the way past blade

before releasing work

7. Replace or sharpen anti-kickback

fingers

23

TROUBLESHOOTING (CONTINUED)

SYMPTOM

Saw makes unsatisfactory cut

POSSIBLE CAUSE(S)

1. Dull blade

2. Blade mounted backwards

3. Gum or pitch on blade

4. Incorrect blade for cut

5. Gum or pitch on table

CORRECTIVE ACTION

1. Sharpen or replace blade

2. Turn blade around

3. Remove blade and clean

4. Change blade to correct type

5. Clean table

24

Model 351.218330

Figure 55 - Replacement Parts Illustration for Rip Fence

26

13

24

11

11

12

2

1

3

3

4

5

6

14

27

28

29

25

30

31

15

7

8

8

10

10

19

18

17

16

20

21 22

23

9

9

25

* Standard hardware item available locally.

REPLACEMENT PARTS LIST FOR RIP FENCE

KEY

NO. PART NO. DESCRIPTION QTY.

1 09845.00 3CMI-6 E-Ring 2

2 31107.00 Locking Handle 1

3 31108.00 8 x 50mm Spring Pin 2

4 31109.00 Bushing 1

5 31110.00 Shaft 1

6 31111.00 Cam 1

7 01923.00 5 x 30mm Spring Pin 1

8 31112.00 Adjusting Plate 2

9 01203.00 3CMI-5 E-Ring 2

10 31113.00 Adjusting Plate 2

11 31114.00 Adjusting Screw 2

12 31115.00 Base 1

13 31116.00 Nylon Screw 2

14 31117.00 Lens 2

15 STD851004 4mm Flat Washer* 2

16 06177.00 4-0.7 x 8mm Flat Head Screw 2

17 31118.00 Fence 1

18 STD851008 8mm Flat Washer* 2

19 STD852008 8mm Lock Washer* 2

20 STD870820 8-1.25 x 20mm Socket Head Bolt* 2

21 31119.00 3.5-1.3 x 10mm Threadforming Screw 2

22 31120.00 Cap 1

23 31121.00 Latch 1

24 18782.00 10 x 50mm Spring Pin 1

25 STD863510 5-0.8 x 10mm Pan Head Screw* 1

26 31122.00 Clamp 1

27 31123.00 Rod 1

28 STD851006 6mm Flat Washer* 1

29 31124.00 Spring 1

30 00652.00 6mm Flat Washer (W) 1

31 STD840610 6-1.0mm Hex Nut* 1

26

Model 351.218330

Figure 56 - Replacement Parts Illustration for Cabinet

10

11

12

14

8

2

2

5

6

7

8

2

3

3

17

6

16

15

25

23

18

19 20

4

9

1

2

2

7

5

21 22

24

13

27

REPLACEMENT PARTS LIST FOR CABINET

* Standard hardware item available locally.

KEY

NO. PART NO. DESCRIPTION QTY.

1 31125.00 Scale 1

2 06346.00 6-1.0 x 12mm Socket Pan Head Screw 30

3 31126.00 Front Corner Support 2

4 31127.00 Front Panel 1

5 STD870820 8-1.25 x 20mm Socket Head Bolt* 4

6 STD852008 8mm Lock Washer* 4

7 STD851008 8mm Flat Washer* 4

8 31128.00 Strain Relief 1

9 31129.00 Line Cord Hook 2

10 09789.00 6-1.0 x 16 Socket Pan Head Screw 2

11 31130.00 Left Panel 1

12 STD851006 6mm Flat Washer* 2

13 STD843610 6-1.0mm Fiber Hex Nut* 2

14 31131.00 Angle Plate 1

15 31132.00 Right Panel 1

16 STD851004 4mm Flat Washer* 4

17 STD852004 4mm Lock Washer* 4

18 STD863410 4-0.7 x 10mm Pan Head Screw* 4

19 STD840812 8-1.25mm Hex Nut* 1

20 31133.00 Rubber Pad 1

21 31134.00 Wrench 1

22 31282.00 Knob 1

23 31135.00 Left Rear Corner Support 1

24 31136.00 Rear Panel 1

25 31137.00 Right Rear Corner Support 1

26 STD835030 8-1.25 x 30mm Hex Head Bolt* 1

RECOMMENDED ACCESSORY

•Zero-clearance Insert 31168.00

28

Model 351.218330

Figure 57 - Replacement Parts Illustration for Rails

31

32

33

28

30

29

27

26

24

24

24 25

25

25

41

7

39 38 36

37

35

21 23

14

13

21

20

15

22

23

23

2

6

8

9

1

10

11

12

19 18

16

17

45

345

43 40

44 34

42

29

REPLACEMENT PARTS LIST FOR RAILS

* Standard hardware item available locally.

∆Not shown.

KEY

NO. PART NO. DESCRIPTION QTY.

1 31138.00 Paddle 1

2 31558.00 Switch 1

3 17933.00 Circuit Breaker,15A 1

4 STD863508 5-0.8 x 8mm Pan Head Screw* 2

5 STD852005 5mm Lock Washer* 2

6 STD851005 5mm Flat Washer* 2

7 01474.00 5mm Serrated Washer 2

8 31128.00 Strain Relief 2

9 31139.00 Tapping Screw 3

10 31140.00 Switch Plate 1

11 STD840610 6-1.0mm Hex Nut* 2

12 STD851006 6mm Flat Washer* 2

13 STD852006 6mm Lock Washer* 2

14 STD833016 6-1.0 x 16mm Hex Head Bolt* 2

15 31141.00 Right Front Rail Cap 1

16 31142.00 Right Front Rail 1

17 31143.00 Front Partition 1

18 31144.00 Left Front Rail 1

19 31145.00 Left Front Rail Cap 1

20 31146.00 Scale (2 piece) 1

21 STD835025 8-1.25 x 25mm Hex Head Bolt* 8

22 31147.00 8-1.25 x 28mm Hex Head Bolt 8

23 STD851008 8mm Flat Washer* 16

24 STD852008 8mm Lock Washer* 16

25 STD840812 8-1.25mm Hex Nut* 16

26 STD835020 8-1.25 x 20mm Hex Head Bolt* 4

27 STD851008 8mm Flat Washer* 4

28 STD852008 8mm Lock Washer* 4

29 STD845812 8-1.25mm Cap Nut* 4

30 31148.00 Brace 1

31 31149.00 Right Rear Rail Cap 1

32 31150.00 Right Rear Rail 1

33 31151.00 Rear Partition 1

34 31152.00 Left Rear Rail 1

35 31153.00 Table Extension 2

36 STD836025 10-1.25 x 25mm Hex Head Bolt* 6

37 STD852010 10mm Lock Washer* 6

38 STD851010 10mm Flat Washer* 6

39 31154.00 Table 1

40 31155.00 Left Rear Rail Cap 1

41 31156.00 Table Insert 1

42 07458.00 5-0.8 x 10mm Flat Head Screw 4

43 31157.00 Magnet 1

44 08560.00 8-1.25 x 16mm Set Screw 2

45 31169.00 Switch Box 1

∆31158.00 Dado Insert 1

∆31105.04 Operator’s Manual 1

30

Model 351.218330

Figure 58 - Replacement Parts Illustration for Base

19 20 21

24

23

22 25

13

18

6

6

6

17

16 13

13

15

1

1

2

1

13

4

9

4

4

4

3

2

2

3

5

5

5

5

5

5

5

2

1

7

7

7

7

8

9

68

3

28

28

34

27

26

26

32

31

30

29

29

33

10

11

14

12

31

REPLACEMENT PARTS LIST FOR BASE

KEY

NO. PART NO. DESCRIPTION QTY.

1 16096.00 8-1.25 x 16mm Socket Pan Head Screw 8

2 06346.00 6-1.0 x 12mm Socket Pan Head Screw 24

3 31163.00 Corner Support 4

4 31164.00 Foot 4

5 STD840812 8-1.25mm Hex Nut* 8

6 31165.00 Caster Assembly 4

7 STD835060 8-1.25 x 60mm Hex Head Bolt* 4

8 31166.00 Front/Rear Base Panel 2

9 31167.00 Caster Support 2

10 STD851010 10mm Flat Washer* 4

11 STD852010 10mm Lock Washer* 4

12 01002.00 10-1.5 x 25mm Socket Head Bolt 4

13 31170.00 Cam Plate Assembly 4

14 STD870616 6-1.0 x 16mm Socket Head Bolt* 2

15 STD870512 5-0.8 x 12mm Socket Head Bolt* 4

16 STD852005 5mm Lock Washer* 4

17 STD851005 5mm Flat Washer* 4

KEY

NO. PART NO. DESCRIPTION QTY.

18 31171.00 Blade Guard Bracket, Front 1

19 31172.00 Blade Guard Bracket, Rear 1

20 22462.00 3-0.5 x 10mm Pan Head screw 4

21 04491.00 3mm Lock Washer 4

22 05981.00 3mm Flat Washer 4

23 31173.00 Push Stick Bracket 1

24 31174.00 Push Stick 1

25 31175.00 Left Base Panel 1

26 31176.00 Caster Shaft 2

27 16109.00 6 x 25mm Spring Pin 4

28 31177.00 Foot Pedal 2

29 31178.00 Caster Support 2

30 31179.00 Dust Chute 1

31 STD840610 6-1.0mm Hex Nut* 2

32 STD851006 6mm Flat Washer* 2

33 31180.00 Right Base Panel 1

34 31181.00 Rip Fence Bracket 2

* Standard hardware item available locally.

32

6

59

15

16

17

58

34

36

37

38

7

8

9

10

11

12

13

20 21

22

36

28

25 26

24

24

26

25

32

33

47

40

74

70

71

72

73

41

65

75

76

77

78

79

79

81

82 83

84 85 87

88

16

17

56

53 46 45 44

30

43

31

29

27 30

86

80

50

51

49

16

52 17 54

55

17

42

66

67

68

69

38

39

60

62

61

37

35

23

2

13

19

18

17

16

14

15

48

45

Model 351.218330

64

63

Figure 59 - Replacement Parts Illustration for Blade Drive

33

* Standard hardware item available locally

REPLACEMENT PARTS LIST FOR BLADE DRIVE

KEY

NO. PART NO. DESCRIPTION QTY.

1 STD835016 8-1.25 x 16mm Hex Head Bolt* 1

2 STD852008 8mm Lock Washer* 1

3 16716.00 8mm Flat Washer (W) 1

4 STD843620 16-2.0mm Fiber Hex Nut* 1

5 STD851016 16mm Flat Washer* 1

6 31182.00 Motor 1

7 STD843217 12-1.75mm Fiber Hex Nut* 1

8 04293.00 6 x 6 x 20mm Key 1

9 31183.00 Motor Pulley 1

10 31184.00 Drive Belt 1

11 31185.00 Arbor Pulley 1

12 02803.00 6-1.0 x 12 Set Screw 1

13 31186.00 Bushing 1

14 STD315225 6202LS Ball Bearing* 1

15 STD870620 6-1.0 x 20mm Socket Head Bolt* 4

16 STD852006 6mm Lock Washer* 7

17 STD851006 6mm Flat Washer* 8

18 31187.00 Height Stop 1

19 31188.00 Motor Bracket 1

20 31189.00 Arbor Locking Bushing 1

21 STD315235 6203LL Ball Bearing* 1

22 31190.00 Spring 1

23 31191.00 Locking Pin w/knob 1

24 STD851005 5mm Flat Washer* 2

25 STD852005 5mm Lock Washer* 2

26 STD863512 5-0.8 x 12mm Pan Head Screw* 2

27 31192.00 Lock Knob 2

28 31193.00 Bevel Stop Support 1

29 31194.00 Spacer 2

30 31195.00 Handle Assembly 2

31 31196.00 Spring 1

32 07215.00 5 x 5 x 15mm Key 2

33 31197.00 Arbor 1

34 31198.00 Shim 2

35 31199.00 Rear Trunnion 1

36 STD851010 10mm Flat Washer* 4

37 STD852010 10mm Lock Washer* 4

38 STD836030 10-1.25 x 30mm Hex Head Bolt* 4

39 31200.00 3CMI-3.5 Retaining Ring 1

40 STD843550 3-0.5mm Fiber Hex Nut* 1

41 31201.00 Adjustment Latch 1

42 31202.00 3-0.5 x 18mm Pan Head Screw 1

43 31203.00 Bushing 1

44 31204.00 Bevel Plate 1

KEY

NO. PART NO. DESCRIPTION QTY.

45 07383.00 3CMI-9 Retaining Ring 1

46 31205.00 Spacer 1

47 31206.00 Bracket 1

48 31207.00 Pin 2

49 31208.00 Spring 1

50 31209.00 Lock Pin 1

51 31210.00 Riving Knife 1

52 31211.00 Plate 1

53 31212.00 Bearing 1

54 31213.00 Locking Knob 1

55 STD870610 6-1.0 x 10mm Socket Head Bolt* 2

56 31214.00 Tilt Shaft 1

57 STD863612 6-1.0 x 12mm Pan Head Screw* 2

58 31215.00 Lower Blade Guard 1

59 31216.00 Arbor Nut 1

60 31217.00 Flange 1

61 31218.00 Blade 1

62 31219.00 3AMI-48 Retaining Ring 1

63 03069.00 5-0.8 x 6mm Set Screw 3

64 31220.00 Pin 1

65 01882.00 5-0.8 x 12mm Hex Head Bolt 1

66 31221.00 Mounting Plate 1

67 31222.00 Spring 1

68 31660.00 Screw 1

69 STD843508 5-0.8mm Fiber Hex Nut* 1

70 31661.00 Spring Plate 1

71 06388.00 3CMI-4 Retaining Ring 1

72 31225.00 Shim Washer 1

73 31226.00 Shaft 1

74 31662.00 Main Trunnion 1

75 STD840812 8-1.25mm Hex Nut* 1

76 00421.00 8-1.25 x 55mm Socket Head Bolt 1

77 31228.00 Rear Trunnion 1

78 31229.00 Elevation Shaft 1

79 01939.00 3 x 20mm Spring Pin 2

80 06821.00 3CMI-12 Retaining Ring 2

81 31230.00 Spacer 2

82 31231.00 Beveled Lock Washer 1

83 31232.00 Shaft Base 1

84 STD863408 4-0.8 x 8mm Pan Head Screw* 1

85 STD851004 4mm Flat Washer* 1

86 31233.00 Pointer 1

87 31234.00 Pointer Base 1

34

6

6

34

7

7

8

9

10

11 12 13

20

20

21

21 22

22

35

28

25

26

27

24

29

31

30

32

33

5

4

4

37

36

9

23

2

2

2

13

3

19

18

17

16

16

14

15

15

15

4

Model 351.218330

Figure 60 - Replacement Parts Illustration for Blade Guard

35

REPLACEMENT PARTS LIST FOR BLADE GUARD

* Standard hardware item available locally.

∆Not shown.

N/A Not available as replacement part.

KEY

NO. PART NO. DESCRIPTION QTY.

1 N/A 6-1.0 x 58mm Hex Head Bolt 1

2 STD840610 6-1.0mm Hex Nut* 3

3 STD851006 6mm Flat Washer* 2

4 N/A Spacer 3

5 31237.00 Left Blade Guard 1

6 N/A Bushing 2

7 N/A Cover 2

8 N/A 4-0.7 x 15mm Set Screw 2

9 N/A 4-0.7 x 10mm Flat Head Screw 4

10 N/A Support 1

11 N/A Body 1

12 31243.00 Right Blade Guard 1

13 N/A Bushing Plate 1

14 N/A Pivot Pin 1

15 N/A 4 x 12mm Spring Pin 3

16 N/A Latch 2

17 N/A 3-0.5 x 8mm Set Screw 1

18 N/A Spring 1

19 N/A Pivot Pin 1

20 N/A 3CMI-9 Retaining Ring 2

21 N/A Pawl 2

22 N/A Bushing 2

23 N/A Support 1

24 31253.00 Knob 1

25 N/A Spacer 1

26 31255.00 Miter Gauge 1

27 STD840508 5-0.8mm Hex Nut* 3

28 STD863520 5-0.8 x 20mm Pan Head Screw* 3

29 STD863410 4-0.7 x 10mm Pan Head Screw* 1

30 STD851004 4mm Flat Washer* 1

31 N/A Pointer 1

32 N/A Block 1

33 N/A Pin 1

34 N/A Stop Pin 1

35 N/A Bar 1

36 N/A Washer 1

37 09956.00 6-1.0 x 8mm Flat Head Screw 1

∆31621.00 Miter Gauge Assembly 1

∆31622.00 Pawl Assembly 1

∆31623.00 Blade Guard Assembly 1

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC

® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC

MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC

Get it fixed, at your home or ours!

Your Home

For expert troubleshooting and home solutions advice:

www.managemyhome.com

For repair – in your home – of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME®(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call anytime for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)

www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR®

(1-888-784-6427)

Au Canada pour service en français:

1-800-LE-FOYERMC

(1-800-533-6937)

www.sears.ca