Craftsman 32 In Spread Width Aerator Spreader Combo 100 Lb Capacity Owners Manual

Craftsman-Spiker-486-24331-Users-Manual-161193 craftsman-spiker-486-24331-users-manual-161193

SPIKER 486.24331 07124331e

: Craftsman Craftsman-32-In-Spread-Width-Aerator-Spreader-Combo-100-Lb-Capacity-Owners-Manual-662033 craftsman-32-in-spread-width-aerator-spreader-combo-100-lb-capacity-owners-manual-662033 craftsman pdf

Open the PDF directly: View PDF .
Page Count: 16

PRINTED IN U.S.A.

Owner's Manual

Model No. 486.24331

32" SPIKER SPREADER

FORM NO. 48070 (REV. 5/20/08)

®

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

CAUTION:

Before using this product, read

this manual and follow all Safety

Rules and Operating Instructions.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

STOP

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

2

TABLE OF CONTENTS

SAFETY RULES ..........................................................3

FULL SIZE HARDWARE CHART ................................ 4

CARTON CONTENTS .................................................5

ASSEMBLY ..................................................................5

OPERATION ..............................................................12

MAINTENANCE ........................................................ 13

STORAGE .................................................................13

REPAIR PARTS ILLUSTRATION .............................. 14

REPAIR PARTS LIST.................................................15

PARTS ORDERING/SERVICE .....................Back Page

MODEL NUMBER: 486.24331

SERIAL NUMBER: __________________

DATE OF PURCHASE: __________________

The model number and serial numbers will be found on a

decal attached to the hitch tube.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

WARRANTY

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Spiker Spreader fails due to a defect in

material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

3

SAFETY

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.

Exercise caution at all times, when using power equipment.

• Read this owner's manual before attempting to

assemble or operate the spiker/spreader.

• Read the towing vehicle owner's manual and know

how to operate the tractor before using the

spiker/spreader attachment.

• Do not allow anyone to ride on or sit on the

spiker/spreader.

• Never allow children to operate the tractor or

spiker/spreader attachment.

• Do not allow adults to operate the tractor or

spiker/spreader without proper instructions.

• Read the chemical label for instructions and

cautions for handling and applying chemicals.

• Wear eye and hand protection when handling and

using lawn chemicals.

• Always begin with the transmission in rst (low) gear

and gradually increase speed as conditions permit.

Maximum towing speed - 10 M.P.H.

• Do not drive too close to a creek or ditch and be alert

for holes and other hazards which could cause you to

loose control of the tractor and spiker/spreader.

• Before operating the vehicle on any grade (hill) refer

to the safety rules in the vehicle owner's manual

concerning safe operation on slopes. Stay off steep

slopes!

• Follow maintenance and lubrication instructions as

outlined in this manual.

Look for this symbol to point out important safety precautions. It means — Attention!! Become

alert!! Your safety is involved.

4

HARDWARE PACKAGE CONTENTS

ABC D E F

K

L

M

GH I

J

SHOWN FULL SIZE

O

P

Q

NOT SHOWN FULL SIZE

N

T

U

S

W

X

FF

DD

GG

BB

CC

EE

AA

Z

Y

HH

II

R

V

REF. QTY. DESCRIPTION

A 2 Hex Bolt, 1/2" x 4"

B 3 Hex Bolt, 5/16" x 2-1/4"

C 2 Hex Bolt, 5/16" x 2"

D 2 Hex Bolt, 5/16" x 1-3/4"

E 2 Hex Bolt, 5/16" x 1-1/2"

F 1 Hex Bolt, 5/16" x 1"

G 1 Hex Bolt, 1/4" x 1 1/4"

H 1 Hex Bolt, 1/4" x 3/4"

I 1 Carriage Bolt. 5/16" x 1-3/4"

J 2 Self-Tapping Screw

K 6 Nylock Hex Nut, 1/4"

L 10 Nylock Hex Nut, 5/16"

M 2 Jam Hex Nut, 1/2"

N 2 Nylock Jam Hex Nut, 1/2"

O 2 Flat Washer, 1/4"

P 2 Nylon Washer, 21/64"

Q 4 Flat Washer, 5/16"

R 4 Flat Washer, 1/2"

REF. QTY. DESCRIPTION

S 10 Flat Washer, 5/8"

T 3 Cotter Pin, 1/8" x 1-1/2"

U 1 Cotter Pin, 3/32" x 3/4"

V 1 Hair Cotter Pin, 1/8"

W 1 Chain with Connector

X 13 Flanged Bearing

Y 1 Compression Spring

Z 1 1/4" Thick Spacer

AA 2 Short Spacer Tube

BB 5 Long Spacer Tube

CC 1 Flow Control Link

DD 1 Ferrule

EE 1 Control Lever Grip

FF 1 Height Adjustment Grip

GG 1 Plastic Wing Nut

HH 1 Flat Head Hitch Pin, 3/8"

II 1 Flow Plate Spring

5

ASSEMBLY

CARTON CONTENTS

1. Chain Cover

2. Flow Control Lever

3. Center Brace

4. Hopper Assembly

5. Hitch Tube (2)

6. Lift Handle

7. Spike Disk (7)

8. Drive Disk Assembly (2)

9. Wheel (2)

10. Transport Tube Assembly

11. Hitch Bracket (2)

12. Spiker Shaft Assembly

1

23

8

12

10

9

4

6

7

5

11

6

FIGURE 1

HITCH TUBE

5/16" FLAT

WASHER

5/16" 1-1/2"

HEX BOLT

5/16" NYLOCK HEX NUT

• Assemble the grip onto the lift handle. See gure 2.

• On the right side, insert a 5/16" x 1-3/4" hex bolt

through a 5/16" at washer and then through the

rear hole in the hopper and the hitch tube. Assemble

the transport tube and then the lift handle onto the

bolt and secure with a 5/16" nylock hex nut. Do not

tighten yet. See gure 2.

• Assemble a 5/16" x 1" hex bolt and 5/16" nylock hex

nut to the bottom hole in the transport tube assembly

and the lift handle. Do not tighten yet. See gure 2.

5/16"FLAT

WASHER

5/16" x 1-3/4"

HEX BOLT

GRIP

LIFT

HANDLE

TRANSPORT TUBE

5/16" NYLOCK

HEX NUT

5/16" x 1"

HEX BOLT

FIGURE 2

FIGURE 3

5/16" x 1-3/4"

HEX BOLT

5/16"FLAT

WASHER 5/16" NYLOCK

HEX NUT

• On the left side, insert a 5/16" x 1-3/4" hex bolt

through a 5/16" at washer and then through the rear

hole in the hopper and the hitch tube. Assemble the

transport tube onto the bolt and secure it with a 5/16"

nylock hex nut. Do not tighten yet. See gure 3.

TOOLS REQUIRED FOR ASSEMBLY

(2) 7/16" Wrenches

(2) 1/2" Wrenches

(2) 3/4" or Adjustable Wrenches

(1) Screwdriver

(1) Pliers

• Remove all parts and hardware packages from the

carton. Lay out all parts and hardware and identify

using the illustrations on pages 3 and 4.

• Attach a hitch tube to the front hole in the right

hand side of the hopper using a 5/16" x 1-1/2" hex

bolt, a 5/16" at washer and a 5/16" nylock hex nut.

Assemble the bolt and washer from inside the hopper.

Do not tighten yet. See gure 1.

• Repeat on the left hand side of the hopper.

7

FIGURE 4

• Fasten the hitch tubes together using three 5/16" x

2-1/4" hex bolts and 5/16" nylock hex nuts. Do not

tighten yet. See gure 4.

FIGURE 5

5/16" x 2-1/4"

HEX BOLT (3)

5/16" NYLOCK

HEX NUT (3)

5/16" x 2"

HEX BOLT (2)

HITCH PIN

HAIR COTTER

PIN (1/8")

5/16" NYLOCK

HEX NUT (2)

• Assemble a 1/2" at washer, a wheel, another 1/2" at

washer and then a 1/2" jam nut onto a 1/2" x 4" hex

bolt. Tighten the nut nger tight and then back off 1/4

to 1/2 turn. See gure 6.

• Assemble the bolt and wheel to the transport tube

using a 1/2" nylock hex jam nut. Tighten the nut but

don't collapse the tube. See gure 6. FIGURE 7

FIGURE 6

1/2" HEX

JAM NUT

TRANSPORT

TUBE

1/2" x 4"

HEX BOLT

1/2" NYLOCK

HEX JAM NUT

1/2" FLAT

WASHER

• Screw a 1/4" nylock hex nut all the way onto the ow

control link. Assemble the ferrule onto the link and

then start a 1/4" nylock hex nut one or two turns onto

the link. See gure 7.

• Assemble the ferrule into the hole at the end of the

ow control lever using a 1/4" nylock hex nut. Tighten

the nut, leaving it loose enough that the ferrule can

pivot freely. See gure 7.

• Assemble the grip onto the end of the ow control

lever. See gure 7.

FLOW

CONTROL

LINK

FERRULE

GRIP

FLOW

CONTROL

LEVER

1/4" NYLOCK

HEX NUT

1/4" NYLOCK

HEX NUT

1/4" NYLOCK

HEX NUT

• Assemble the hitch brackets to the hitch tubes using

two 5/16" x 2" hex bolts and 5/16" nylock hex nuts. Do

not tighten. See gure 5.

• Assemble the hitch pin through the hitch brackets and

secure with the hair cotter pin. See gure 5.

IMPORTANT: Do not collapse the at ends of the hitch

tubes when tightening the bolts in the next step.

• Tighten, but do not overtighten the two 5/16" x

1-1/2" hex bolts assembled in gure 1.

Tighten, but do not overtighten the two 5/16" x

1-3/4" hex bolts assembled in gures 2 and 3. The lift

handle must be able to pivot.

Tighten the hex bolts assembled in gure 4 and 5.

• If the wheel does not spin freely, back off the nylock

jam nut and then the plain jam nut 1/4 to 1/2 turn each.

• Assemble a wheel to the other side. See gure 6.

8

FIGURE 9

FIGURE 8

• Insert the 5/16" x 1-3/4" carriage bolt up through the

slot and secure it with a nylon washer and the plastic

wing nut. See gure 9.

• Move the lift handle into the locked position as shown

in gure 9 and then tip the spreader back to rest on

the wheels and the rear of the hopper.

1/4" x 3/4"

HEX BOLT

1/4" FLAT

WASHER

CENTER

BRACE

1/4" x 1-1/4"

HEX BOLT

1/4" FLAT

WASHER

1/4" HEX

LOCK NUT

1/4" NYLOCK

HEX NUT

PLASTIC WING NUT NYLON

WASHER

5/16" x 1-3/4"

CARRIAGE BOLT

LOCKED POSITION

• Place the ow control lever into the slot in the hopper.

See gure 8.

• Place the center brace into the hopper. Insert the 1/4"

x 1-1/4" hex bolt through the center brace and the

front of the hopper. Assemble a 1/4" at washer, the

ow control lever and a 1/4" nylock hex nut onto the

bolt. Do not tighten yet. See gure 8.

• Insert the 1/4" x 3/4" hex bolt through the center

brace and the rear of the hopper. Assemble a 1/4" at

washer and 1/4" nylock hex nut onto the bolt. Tighten

both the front and rear bolts. See gure 8.

FIGURE 10

EXTENSION

SPRING

NYLON

WASHER

3/32" x 3/4"

COTTER PIN

FLOW

CONTROL

LEVER

FLOW CONTROL LINK

FEED PLATE

1/4" NYLOCK

HEX NUT

1/4" NYLOCK

HEX NUT

1/4" NYLOCK

HEX NUT

• Move the ow control lever as far as it will go to the

"OFF" position. Push the feed plate back as far as it

will go to the closed position. See gure 10.

• Place a nylon washer onto the bent end of the ow

control link and then insert the link into the feed plate

bracket. Secure it with a 3/32" x 3/4" cotter pin. See

gure 10.

• Tighten the lower 1/4" nylock hex nut until it touches

the bottom of the ferrule, then tighten the upper 1/4"

nylock hex nut until it is snug against the top of the

ferrule. See gure 10.

• Hook the open end of the spring into the feed plate.

Place the closed end of the spring onto the end of the

hex bolt in the ow control lever. Secure it with a 1/4"

nylock hex nut. See gure 10.

• Open and close the feed plate using the ow control

lever. Check to make sure the feed plate is closed

completely when the lever is in the "OFF" position.

If the feed plate does not close completely, adjust

the 1/4" nylock hex nuts on the ow control link. See

gure 10.

9

FIGURE 11

• Push two ange bearings into each of the drive disk

assemblies. See gure 11.

• Push a ange bearing into each of the seven drive

disks, from the side shown in gure 12.

FIGURE 12

• Press anged bearings into both of the end plates.

See gure 13.

• Place the 1/4" thick spacer onto the spike disk

shaft and then insert the shaft through the anged

bearing in the left hand end plate. See gure 13.

FIGURE 13

SPIKE DISK

LONG SPACER TUBE

• Place a short spacer tube, a drive disk, a 5/8" at

washer, another drive disk and a second 5/8" at

washer onto the shaft. Fit the short spacer tube onto

the anged bearing in the end plate. See gure 14.

FIGURE 14

FIGURE 15

IMPORTANT: When assembling the spike disks, be sure

they face in the direction shown in the instructions.

• Place two spike disks, separated by a long spacer

tube, onto the shaft. Fit the long spacer tube onto the

ends of the anged bearings in the disks. See gure

15.

DRIVE DISKS

5/8" FLAT WASHER

SHORT SPACER

TUBE

FLANGED

BEARING

FLANGED

BEARING

DRIVE DISK

ASSEMBLY

FLANGED

BEARING

SPIKE DISK

FLANGED

BEARING

FLANGED

BEARING

1/4" THICK SPACER

SPIKE DISK SHAFT

10

5/8" FLAT

WASHER

COMPRESSION

SPRING

• Place a 5/8" at washer, the compression spring and

another 5/8" at washer onto the shaft. See gure 16.

SPIKE DISK

LONG SPACER TUBE

• Place two spike disks, separated by a long spacer

tube, onto the shaft. Fit the long spacer tube onto the

ends of the anged bearings in the disks. See gure

17.

FIGURE 16

FIGURE 17

• Place two 5/8" at washers separated by a long

spacer tube onto the shaft. See gure 18.

FIGURE 18

5/8" FLAT WASHER

LONG SPACER TUBE

SPIKE DISK

LONG SPACER TUBE

FIGURE 19

• Place two spike disks, separated by a long spacer

tube, onto the shaft. Fit the long spacer tube onto the

ends of the anged bearings in the disks. See gure

19.

11

• Place two 5/8" at washers separated by a long

spacer tube onto the shaft. See gure 20.

FIGURE 20

SPIKE DISK

SHORT SPACER TUBE

• Place a spike disk and a short spacer tube onto the

shaft. Fit the short spacer tube onto the ends of the

anged bearings in the spike disk and in the end

plate. Push the shaft on through the anged bearing

in the end plate. See gure 21.

5/8" FLAT WASHER

LONG SPACER TUBE

FIGURE 21

FIGURE 23

• Place a 5/8" at washer onto the end of the spike disk

shaft and secure the shaft with a 1/8" x 1-1/2" cotter

pin. See gure 22.

• Fasten the two drive disks to the shaft using two 1/8"

x 1-1/2" cotter pins. See gure 22.

5/8" FLAT

WASHER

1/8" x 1-1/2"

COTTER PIN

DRIVE DISKS

FIGURE 22

• Assemble the chain onto the two sprockets on the

left side of the hopper. Fasten the ends of the chain

together using the connecting link. See gure 23.

• Place the chain cover over the chain and fasten it to

the hopper end plate using two self tapping screws.

See gure 23.

CONNECTING

LINK

CHAIN

SELF

TAPPING

SCREW

12

OPERATION

KNOW YOUR SPIKER SPREADER

Read this owner's manual and safety rules before operating your Spiker Spreader.

Compare the illustration below with your Spiker Spreader to familiarize yourself with the various controls and their

locations.

FLOW CONTROL LEVER Opens and closes the ow

plate at the bottom of the hopper.

LIFT HANDLE Raises the unit for transport or lowers it

for spreading and aerating.

PLASTIC WING NUT Tightens at desired setting to

control how far the ow control lever can open the ow

plate.

HOW TO USE YOUR SPIKER/SPREADER

• Refer to the instruction label on the material package

and to the instruction decal on your spreader to help

determine the proper spreader setting and application

rate. Also see the Setting Chart on page 13 of this

manual for a general range of settings for commonly

used materials.

• Determine the approximate square footage of the

area to be covered and estimate the amount of

fertilizer or seed required.

• Move the spreader to the area where application is to

begin.

FIGURE 24

FLOW CONTROL LEVER

PLASTIC WING NUT

LIFT HANDLE

• Loosen the plastic wing nut and move it to the desired

setting. Retighten the nut. See gure 24.

• Making sure the ow control lever is in the "OFF"

position, ll the hopper, breaking up any lumps.

• Lower the aerator spikes to the operating position.

• Start the spreader in motion and then move the

ow control lever to the "ON" position (against the

plastic wing nut) as you travel across your lawn. The

recommended towing speed is 3 m.p.h.

• Do not make sharp turns with spikes in the ground.

• Raise aerator spikes to transport position when

crossing over concrete or other hard surfaces.

• Do not aerate if the ground is extremely hard or dry.

If ground is too dry, sprinkle or water for one to two

hours prior to use.

• Do not aerate if the ground is too wet (muddy).

IMPORTANT: Always place ow control lever in the

"OFF" position to prevent excess fertilizer from being

released when lling the spreader and when stopping or

turning.

ALIGN AND TIGHTEN WING NUT

AT DESIRED FLOW SETTING

12345

67

89

10 11

12 13

14 15

16 17

18

OFF

0

WING NUT SET AT "5"

13

OPERATING TIPS

• To help prevent granular material from compacting

and clogging the hopper, avoid unnecessary towing

when the hopper ow plates are closed.

• Reduce the ow setting for speeds slower than

3 M.P.H. and increase the setting for higher speeds.

• To avoid misses or striping, overlap the previous

wheel tracks by approximately 5" to 6".

FIGURE 25

MAINTENANCE

Spike points are sharp. Exercise caution

when handling or working near spike disks.

Service Dates

Check for loose fasteners X

Lubrication X

Cleaning X

MAINTENANCE SCHEDULE

Fill in dates as you

complete regular service.

Before each use

After each use

Every year

Before storage

CUSTOMER RESPONSIBILITIES

• Read and follow the maintenance schedule and the maintenance procedures listed in this section.

CHECK FOR LOOSE FASTENERS

• Before each use make a thorough visual check of

the spiker spreader for any bolts and nuts which may

have loosened. Retighten any loose bolts and nuts.

LUBRICATION

• Apply a few drops of oil to wheels and to plastic

bearings in spike disks and at end of spike axle.

• Remove chain cover, clean and oil drive chain.

CLEANING

• Always empty spiker spreader after each use, storing

leftover material in it's original bag.

• Wash the spiker spreader and dry thoroughly after

each use.

• For easiest application, rst apply material across

both ends of the area. Two or three passes on each

end are sufcient. Then apply material back and forth

as shown. Use the end areas for turning around,

shutting off the spreader as you enter the end areas

and turning the spreader on again as your leave the

end areas for your next pass. See gure 25.

• If lawn is odd shaped, spread a border around the

edges and then spread between the border.

• Be careful when spreading around ornamental plants

because weed control chemicals can damage these

plants.

• Empty the spiker spreader, storing leftover material in

it's original bag.

• Apply a light coat of oil on exposed metal to help

prevent rust.

STORAGE

• Wash the spiker spreader and dry thoroughly before

storing.

• Store in a clean, dry area.

Flow Rate Setting

MATERIAL TYPE At 3 M.P.H.

SETTING CHART

Fertilizer Granular / Pelleted 5-6 / 6-7

Grass Seed Fine / Coarse 5-6 / 7-8

3 M.P.H. is equivalent to traveling 100 feet in 23 seconds.

14

PARTS

REPAIR PARTS FOR MODEL 486.24331

A

B

A

C

1

2

3

5

6

10

16

19

10

11 63

12

12

62

13

21

14

13

7

8

8

9

13

17

49

50

51

52

53

54

55

18

28 29

33

35

36

37

38

39

40

41

42

30

31

22

23

25

23

26

27

42

42

43

43 44

44

46

47

48

45

56

57

57

58

59

58

58

15

59

43

34

43

54

43

58

59

F

B

42

32

24

C

20

60

61

4

59

59

59

15

REPAIR PARTS FOR MODEL 486.24331

REF. PART QTY DESCRIPTION

NO. NO.

REF. PART QTY DESCRIPTION

NO. NO.

1 47931 1 Hopper

2 24736 1 End plate, Right Hand

3 24735 1 End plate, Left Hand

4 48418 12 Rivet, Pop

5 24747 1 Brace, Center

6 64104 1 Assembly, Agitator Shaft

7 47963 2 Bearing, Hex Flange

8 24739 2 Blade, Agitator

9 47978 10 Screw, Hex Washer Hd, #8-32

10 R19172410 2 Washer, 17/32" x 1-1/2" x 10 Ga.

11 46838 2 Spacer, .8" I.D.x1" O.D. x .50" Lg.

12 R19171616 4 Washer, 17/32" x 1" x 16 Ga.

13 43093 3 Pin, Cotter 1/8" x 1-1/2"

14 45133 1 Spacer, .5" I.D. x 1" O.D. x .59" Lg.

15 23520 1 Spacer, .66" I.D.x1.25" O.D. x .25"

16 47962 1 Spring, Flow Plate

17 64106 1 Assembly, Spiker Shaft

18 64107 1 Assembly, Transport Tube

19 24743 1 Lever, Flow Control

20 63956 2 Drive Disk

21 24332 7 Disk, Spike (7")

22 47953 1 Cover, Chain

23 47944 2 Tube, Hitch

24 24746 1 Lift, Handle

25 47961 2 Wheel, 10" x 1-5/8"

26 24741 1 Plate, Flow

27 23981 2 Bracket, Hitch

28 24539 1 Bracket, Feed Plate

29 728-3001 2 Rivet, Pop 5/32 (Stainless)

30 47960 1 Chain with Connector

31 43848 1 Grip, Control Arm .187" x .75"

32 43943 1 Grip, Height Adjustment 32"/38"

33 47959 1 Link, Flow Control

34 47969 1 Ferrule, 5/16" Thread x 1/4" Hole

35 43224 3 Bolt, Hex 5/16" x 2-1/4"

36 44180 2 Bolt, Hex 5/16" x 2"

37 43085 2 Bolt, Hex 5/16" x 1-1/2"

38 43084 2 Bolt, Hex 5/16" x 1-3/4"

39 43063 1 Bolt, Hex 5/16" x 1"

40 44731 2 Screw, Self Tapping 1/4" x 1"

41 43012 1 Bolt, Hex 1/4-20 x 3/4"

42 47810 10 Nut, Nylock Hex 5/16"

43 47189 6 Nut, Nylock Hex 1/4"

44 43088 2 Washer, Flat 1/4"

45 43081 4 Washer, Flat 5/16"

46 45100 2 Bolt, Hex 1/2" x 4" Full Thread

47 43019 2 Nut, Hex Jam 1/2"

48 48115 2 Nut, Nylock Hex Jam 1/2"

49 43343 1 Pin, Hair Cotter #4 (1/8")

50 44101 1 Pin, Cotter 3/32" x 3/4"

51 47623 1 Pin, Flat Head Hitch, 3/8" Dia.

52 44215 1 Bolt, Carriage 5/16" x 1-3/4"

53 712-0421 1 Nut, Plastic Wing 5/16"

54 1543-69 2 Washer, Nylon 21/64"

55 46524 5 Spacer Tube, Long

56 47777 1 Spring, Compression

57 46497 2 Spacer Tube, Short

58 741-0249 13 Bearing, Flanged PV80 .63 I.D.

59 R19212016 10 Washer, Flat 5/8" (21/32" x 1-1/4")

60 1509-90 1 Bolt, Hex 1/4-20 x 1-1/4"

61 48173 2 Washer, 13/16" x 1-1/2" x 1/16"

62 46557 1 Push Nut, 1/2"

63 44137 5 Washer, Flat .518 x 1 x.02

48070 1 Owner's Manual

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC

® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC

MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC

Get it fixed, at your home or ours!

Your Home

For repair – in your home – of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME®(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

For expert home solutions advice: www.managemyhome.com

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)

Call anytime, day or night

www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR®

(1-888-784-6427)

Au Canada pour service en français:

1-800-LE-FOYERMC

(1-800-533-6937)

www.sears.ca