Craftsman 486 24219 Users Manual

486.24219 24219e

2015-01-05

: Craftsman Craftsman-486-24219-Users-Manual-160475 craftsman-486-24219-users-manual-160475 craftsman pdf

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

Owner's Manual

STOP

DETHATCHER FOR SWEEPERS
Model No. 486.24219

DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388

•
•
•
•
•

CAUTION:

Before using this product, read
this manual and follow all Safety
Rules and
Operating Instructions.

Safety
Assembly
Operation
Maintenance
Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman

FORM NO. 48830 (REV. 6/06)

PRINTED IN U.S.A.

TABLE OF CONTENTS
SAFETY RULES........................................................... 2
FULL SIZE HARDWARE CHART................................. 3
CARTON CONTENTS.................................................. 4
ASSEMBLY................................................................... 4

OPERATION................................................................. 6
MAINTENANCE/STORAGE......................................... 6
REPAIR PARTS .......................................................... 7
PARTS ORDERING/SERVICE......................Back Page

WARRANTY
ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Dethatcher fails due to a defect in material
or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair (or replacement
if repair proves impossible).
If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

The model number and serial numbers will be found on a
decal attached to the dethacther.
You should record both the serial number and the date of
purchase and keep in a safe place for future reference.

MODEL NUMBER:

486.24219

SERIAL NUMBER:

__________________

DATE OF PURCHASE:__________________

SAFETY
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.
Exercise caution at all times, when using power equipment.
• Read this owners manual carefully for operating and
service instructions before attempting to assemble or
operate the dethatcher. Be thoroughly familiar with the
proper use of the dethatcher.
• Read the vehicle owners manual and vehicle safety
rules, and know how to operate the vehicle before
using the dethatcher.
• Read the lawnsweeper owners manual and safety
rules, and know how to operate the lawnsweeper
before using the dethatcher.
• Never allow children to operate the tractor or
dethatcher attachment, and do not allow adults to
operate without proper instructions.
• This dethatcher attachment has sharp tine points.
Always handle with care and wear substantial foot
wear when operating this dethatcher.
• Do not allow anyone to ride or sit on the dethatcher,
lawnsweeper or towing vehicle.
• Keep the area of operation clear of all persons,
particularly small children, and also pets.

• Always begin with the transmission in first (low) gear
and engine at low speed, and gradually increase
speed as conditions permit.
• Vehicle braking and stability may be affected with the
attachment of this equipment. Be aware of changing
conditions on slopes. Refer to safety rules in the
vehicle owner's manual concerning safe operation on
slopes. STAY OFF OF STEEP SLOPES.
• Always operate up and down a slope, never across
the face of a slope
• This equipment should be operated at reduced speed
on rough terrain, along creeks and ditches and on
hillsides, to prevent tipping and loss of control. Do not
drive too close to a creek or a ditch.
• Follow the maintenance instructions as outlined in this
owners manual.
Look for this symbol to point out important safety
precautions. It means — Attention!!
Become alert!! Your safety is involved.

HARDWARE PACKAGE CONTENTS
SHOWN FULL SIZE
E
A

F
D

G
K

NOT SHOWN FULL SIZE
P

N
O

REF. QTY.

A 1
B
7
C 2
D 2
E 1
F 2
G 2
H 14
I 2

DESCRIPTION

Hex Bolt, 1/2" x 3-1/2"
Hex Bolt, 5/16" x 1-1/2"
Clevis Pin, 5/16" x 1-3/8"
U-Bolt
Transport Hook
Washer, 5/16"
Washer, 1/2"
Washer, 3/8"
Hair Cotter Pin, 3/32"

REF.

QTY.

J
4
K
7
L 1
M 1
N 2
O 2
P 2
Q 1

DESCRIPTION
Hex Nut, 1/4"
Hex Nut, 5/16"
Jam Nut, Plain 1/2"
Jam Nut, Nylock 1/2"
Vinyl Cap
Conduit Clamp
Keeper Bracket
Nylon Tie

ASSEMBLY
CARTON CONTENTS

NOTE: On sweepers smaller than 42", use only five spring
tines.

1. Spring Tines (7)
2. Frame Assembly
3. Gauge Wheel

• Assemble a vinyl cap onto each end of the frame tube.
See figure 1.
5/16" x 1-1/2"
HEX BOLT

VINYL CAP

3/8" WASHER

2
5/16" NYLOCK NUT
VINYL CAP

FIGURE 1

• Assemble a 1/2" washer, the wheel, another 1/2"
washer and the 1/2" plain jam nut onto the
1/2" x 3-1/2" hex bolt. See figure 2.
• Insert the bolt through the welded bracket and
assemble the 1/2" nylock jam nut onto the bolt. Adjust
the nuts so that there is no end play in the wheel and
then tighten the nuts securely against the welded
bracket. Make sure the wheel still turns freely. See
figure 2.

TOOLS REQUIRED FOR ASSEMBLY
(1)
7/16" Wrench
(2) 1/2" Wrenches
(2)
3/4" or Adjustable Wrenches
(1)
Knife

Use this hole for
42" & 46" sweepers
Use this hole for
smaller sweepers

REMOVAL OF PARTS FROM CARTON
• Remove all parts and hardware packages from the
carton. Lay out all parts and hardware and identify
using the illustrations on pages 3 and 4.
• Turn the frame assembly as shown in figure 1.
• Assemble seven spring tines to the top of the frame
tube. Use a 5/16" x 1-1/2" hex bolt, two 3/8" flat
washers and a 5/16" nylock nut for each spring tine.
Place one 3/8" flat washer on top of the frame tube
and the second 3/8" flat washer on top of the spring
tine. See figure 1.

1/2" NYLOCK
JAM NUT
1/2" JAM NUT
1/2" WASHER
1/2" WASHER
1/2" x 3-1/2"
HEX BOLT

FIGURE 2

If you have a 30" sweeper, skip these steps.
• Make sure the sweeper height adjustment handle is
still set to about the middle of it's adjustment range.
• Center the dethatcher with the sweeper.
• Assemble the keeper brackets (bend to the inside)
to the sweeper's hitch tube, outside of the conduit
clamps. Use a u-bolt and two 1/4" nylock nuts per
bracket. Position the keeper brackets against the sides
of the conduit clamps, approximately perpendicular
to the ground. Tighten the nuts without bending the
keeper brackets. See figure 5.

• Assemble a conduit clamp onto each end of the
sweeper height adjustment tube so that the straight
part of the clamp is on top of the tube. See figure 3.
• Remove the hitch brackets and the bolts, if present,
from the ends of the sweeper's hitch tubes. Slide the
transport hook onto the L.H. hitch tube as shown in
figure 3.
• Reassemble the hitch brackets and bolts to the hitch
tubes. Refer to your sweeper owner's manual.

KEEPER BRACKET
U-BOLT

TRANSPORT
HOOK
CONDUIT
CLAMP

FIGURE 3
• Connect the sweeper to the tractor. Set the sweeper
height adjustment handle to about the middle of it's
adjustment range.
• Place the dethatcher in front of the sweeper housing,
underneath the hitch tubes.
• Connect the dethatcher to the conduit clamps using
two 5/16" x 1-3/8" clevis pins, 5/16" washers and
3/32" hair cotter pins. See figure 4.

1/4" NYLOCK NUT

FIGURE 5

• Lift the front of the dethatcher and secure it in
transport position using the transport hook. See figure
6.
• To keep the transport hook from sliding back along
the hitch tube, you can fasten the supplied nylon tie
around the hitch tube behind the transport hook. See
figure 6.

HEIGHT ADJUSTMENT
MIDDLE SETTING
5/16" x 1-3/8"
CLEVIS PIN

NYLON TIE

5/16" WASHER

TRANSPORT HOOK

3/32" HAIR
COTTER PIN

FIGURE 4

FIGURE 6

OPERATION
HOW TO USE YOUR DETHATCHER

USING THE DETHATCHER

RAISING/LOWERING THE DETHATCHER

Regular removal of thatch is critical to the maintenance
of a healthy lawn. Thatch is layer of stems, clippings,
runners, roots and leaves that have not decayed.
Excessive thatch prevents air, water and fertilizer from
reaching the roots. The dethatcher will effectively dislodge
excessive thatch from your lawn.

• To raise the dethatcher for transport, lift up on the
front of the dethatcher and secure it with the transport
hook. Lower the dethatcher by releasing the transport
hook.

• Start with the tractor in low gear. Vary the forward
speed to determine the best speed for maximum
dethatcher performance.

SETTING THE OPERATING POSITION
• The operating height of the dethatcher is controlled
by the gauge wheel at the front of the dethatcher
and is not adjustable. The correct wheel position
was determined in figure 2 when you assembled the
wheel.

• Use a crisscross pattern to achieve the most even
removal of thatch.
• On slopes, always operate in an up and down
direction only.

• Set the sweeper to the desired operating height. (The
best height is usually with the brushes set about 1/2"
down into the grass.) Refer to your sweeper owner's
manual for sweeper.

• Avoid extremely sharp turns.
• Avoid towing the dethatcher across sudden steep
dips in the ground while dethatching. Loss of ground
contact with the gauge wheel could cause the
dethatcher to be pulled back underneath the sweeper.

MAINTENANCE / STORAGE
CUSTOMER RESPONSIBILITIES

• Read and follow the maintenance schedule and the maintenance procedures listed in this section.
MAINTENANCE SCHEDULE
Fill in dates as you
complete regular service.

e
us se on ge
ch ch u eas tora
a
s
e e ea y s e
for fter ver efor
e
E
B
A
B

Check for loose fasteners X
Check for worn or damaged parts X
Cleaning X

Service Dates

X
X

•

Before each use, check all nuts and bolts for
tightness.

•

If rust appears on the spring tines, sand lightly and
coat with enamel paint.

•

Clean after each use to help prevent rust.

•

Always store in a dry area, and coat exposed metal
with light oil when not in use.

PARTS
REPAIR PARTS FOR MODEL 486.24219 DETHATCHER
4
6

19
2

6
15

1
8
5
9
15

1
2
3
4
5
6
7
8
9
10
11

PART
NO.

QTY.

64650 1
46761
7
48098 1
43085
7
43081 2
43070 14
43083
7
48812 2
47413 2
43055 2
44025 1

DESCRIPTION

Spring Mount Frame Assem.
Spring Tine
Gauge Wheel
Hex Bolt, 5/16-18 x 1-1/2"
Washer, 5/16"
Washer, 3/8"
Nylock Nut, 5/16-18
Clevis Pin, 5/16" x 1-3/8"
Clamp
Hair Cotter Pin, 3/32"
Hex Bolt, 1/2-13 x 3-1/2"

14
12

REF.
NO.

PART
NO.

QTY.

12 R19171616 2
13
43019 1
14
48115 1
15
48813 2
16
43178
4
17 726-0178 1
18
48811 2
19 25054 2
20
44481 2

48830 1

DESCRIPTION
Washer, 1/2"
Jam Nut, Plain 1/2-13
Jam Nut, Nylock 1/2-13
U-Bolt, 1/4-20
Nylock Nut, 1/4-20
Nylon Tie
Hook, Transport
Bracket, U-Bolt Clamp
Vinyl Cap
Owner's Manual

Get it fixed, at your home or ours!
Your Home

For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.

1-800-4-MY-HOME®

(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com

www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)
www.sears.com

To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparación
a domicilio, y para ordenar piezas:

Au Canada pour service en français:

1-800-LE-FOYER MC

1-888-SU-HOGAR®

(1-800-533-6937)
www.sears.ca

(1-888-784-6427)

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2006:12:05 16:32:39-06:00
Modify Date                     : 2008:08:28 09:46:06-05:00
Metadata Date                   : 2008:08:28 09:46:06-05:00
Creator Tool                    : Adobe InDesign CS2 (4.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7456 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:28ae85e4-3fd0-428a-b5ae-c2886eabc12f
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:877a6da0-5501-11d9-ae0d-bd192f2555c2
Contributor Resources Document ID: uuid:5355c267-f419-4c3c-b70e-a4c16bf68c63
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Document ID  : uuid:bbdb7194-0340-4013-a1a5-79e232d06b16, uuid:98a1b489-51d1-4599-a65e-980de4df60b0, uuid:0c428577-cde1-47e3-a667-0f510ff7dd5a, uuid:5355c267-f419-4c3c-b70e-a4c16bf68c63, uuid:12faf70c-e663-4e53-9120-6fc9b8e0017e, uuid:0edbae4c-5703-47a0-b800-227e12d618e1, uuid:ecebcee9-da06-4b55-a54d-c52dc7d8b728, uuid:6b8de4be-8c29-48c1-8105-d83230671afe, uuid:309084e2-57b7-4363-97e8-aa842d3f16d9, uuid:3964d39c-66cc-42d2-96c5-74c4c4fbf4cf, uuid:ac59f190-4ce7-4f3e-9917-36ee4138946d, uuid:4eccd62e-1d04-4cb2-835f-f9605245b6bb, uuid:3f676586-79d7-4bb6-bd20-b42bc7be0733, uuid:f975778a-87fb-4fae-9b85-e159daff636d, uuid:6ca2596f-73d4-4ca0-9882-d0dcb0d0b989, uuid:253da362-e986-4431-bd58-b144f1e0138a
Format                          : application/pdf
Page Count                      : 8
Creator                         : Adobe InDesign CS2 (4.0.4)

EXIF Metadata provided by EXIF.tools

Craftsman 486 24219 Users Manual

486.24219 24219e

Navigation menu

Versions of this User Manual:

Views

Navigation