Craftsman 486 242223 Users Manual

Craftsman Lawn Sweeper 486.242223 spin_prod_667506901

Craftsman 42 Sweeper

: Craftsman Craftsman-486-242223-Users-Manual-160941 craftsman-486-242223-users-manual-160941 craftsman pdf

Open the PDF directly: View PDF .
Page Count: 20

42" HIGH SPEED

LAWNSWEEPER

Model No's. 486.242223

Owner's Manual

CAUTION:

Before using this product, read

this manual and follow all Safety

Rules and Operating Instructions.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

PRINTEDINU.S.A. FORMNO.41900rev.(01/30/12)

SearsBrandManagementCorporation,HoffmanEstates,IL60179U.S.A.

www.craftsman.com

®

STOP

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

2

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.

Exercisecautionatalltimes,whenusingpowerequipment.

1. Readthevehicleandsweeperownersmanuals

andknowhowtooperateyourvehicleandsweeper

beforeusingthissweeperattachment.Alwaysinstruct

otherusersbeforetheyoperatethesweeper.

2. Donotpermitchildrentooperatesweeper.

3. Donotpermitanyonetorideonsweeper.

4. Neverattachthehopperropetoanypartofyourbody

orclothing!Neverholdontotheropewhiletowing

thesweeper!Attachtheropetothetowingvehicleto

keep it away from wheels and rotating parts.

5. Operate the sweeper at reduced speed on rough

terrain,nearditchesandonhillsidestopreventloss

of control.

6. Vehiclebrakingandstabilitymaybeaffectedwith

theattachmentofthissweeper.Donotllsweeper

tomaximumcapacitywithoutcheckingthecapability

ofthetowingvehicletosafelypullandstopwiththe

sweeper attached. Stay off of steep slopes.

7. Stopandinspectvehicleandsweeperfordamage

afterstrikinganobject.Repairanydamagebefore

continuing operation.

8. Keepsweeperawayfromre.Excessiveheatcan

damagethebrushesandhopperbagandcould

causethebaganditscontentstoburn.

9. Before storing the sweeper, always empty the hopper

bagtoavoidspontaneouscombustion.

10. Followmaintenanceandlubricationinstructionsas

outlined in the maintenance section of this manual.

Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!

Become alert!! Yoursafetyisinvolved.

MaintenanceSchedule .................................................. 13

Storage ..........................................................................13

ServiceandAdjustments ...............................................14

Troubleshooting .............................................................14

RepairPartsIllustration .................................................15

RepairPartsList ............................................................ 16

PartsOrdering .................................................BackCover

Safety Rules ....................................................................1

Warranty ..........................................................................2

AccessoriesandAttachments .........................................3

CartonContents ..............................................................3

FullSizeHardwareChart ................................................4

SweeperAssemblyInstructions ...................................... 5

HopperAssemblyInstructions .........................................7

Operation ....................................................................... 12

MODELNUMBER: 486.242223

SERIALNUMBER: ____________________

DATEOFPURCHASE: ____________________

WARRANTY

TABLE OF CONTENTS

Themodelandserialnumberswillbefoundonadecal

attached to the lawnsweeper.

Youshouldrecordboththeserialnumberandthedateof

purchase and keep in a safe place for future reference.

SAFETY

CRAFTSMAN ONE YEAR FULL WARRANTY

For one year from the date of purchase, this product is warranted against any defects in material or workmanship.

Adefectiveproductwillbereplacedfreeofcharge.

Forwarrantycoveragedetailstoobtainfreereplacement,visitthewebsite:www.craftsman.com

Thiswarrantyisvoidifthisproductiseverusedwhileprovidingcommercialservicesorifrentedtoanotherperson.

Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

3

ACCESSORIES AND ATTACHMENTS

TheFrontMountDethatcher,Model486.24219attaches

tothelawnsweepertohelploosenandremovedead

grass and thatch from the lawn while sweeping.

These accessories were available when the unit was purchased. They are also available at most Sears retail

outlets and service centers. Most Sears stores can order repair parts for you when you provide the model

numbers of your tractor and sweeper

1

2

3

5

6

7

2

16

9

4

10

11

13

14

10

12

11

12

15

8

REF PART NO. QTY DESCRIPTION

1– – – 1 SweeperHousingAssembly

2 49766 2 BagArmTube

3 46777 HitchTube,L.H.(LeftHand)

4 24192 1 HitchBracket

523687 1 HitchBracket,Bent

6 46776 1 HitchTube,R.H.(RightHand)

7– – – 1 BrushAssembly(RightHand)

8 – – – 1 BrushAssembly(LeftHand)

REF PART NO. QTY DESCRIPTION

9 49768 1 HopperBag

10 47477 2 RearHopperTube

11 49765 2 UpperHopperTube

12 48726 2 LowerHopperTube

13 46823 1 PivotRod

14 43938 2 HopperSupportRod

15 24189 1 Bag Frame Strap

16 43737 1 Rope

CARTON CONTENTS

4

REF PART NO. QTY DESCRIPTION

A 46782 2 HexBolt,5/16-18x3"Lg.

B43224 2 HexBolt,5/16-18x2-1/4"Lg.

C 43084 4 HexBolt,5/16-18x1-3/4"Lg.

D 43661 4 HexBolt,1/4-20x1"

E 43978 4 CurvedHeadBolt,1/4-20x1"

F47189 8NylockNut,1/4"

G47810 8NylockNut,5/16"

H 44917 2 Palnut,3/8"

HARDWARE PACKAGE CONTENTS

REF PART NO. QTY DESCRIPTION

I23368 2 HitchSpacer,3/4"

J46867 2 ClevisPin,1/4"x1-3/4"

K48365 2 ClevisPin,1/4"x1-1/8"

L 48366 2 ClevisPin,3/8"x1/2"

M 43055 7 HairpinCotter,3/32"

N 23353 1 HitchPin

O44481 2 VinylCap

A B C ED

M

N

O

J

I

SHOWN FULL SIZE

NOT SHOWN FULL SIZE

KL

G

FH

5

TOOLS REQUIRED FOR ASSEMBLY

(1) Hammer

(2) 7/16"Wrenches

(2) 1/2"Wrenches

ASSEMBLY

STEP 2: (SEE FIGURE 1)

• Eachbrushassemblyhasonebrushretainer

markedwitheitherredorblackink.Layoutthebrush

assembliesasshownsothatthebrushretainers

markedwithinkareinthemiddlewiththeblackone

on your right and the red one on your left.

OVERLAP BRISTLES

BRUSH RETAINER

MARKED RED

BRUSH RETAINER

MARKED BLACK

• Attachthebrushassemblywiththeblackbrush

retainertotherightendofthebrushshaftusingtwo

hexbolts(D)andnylocknuts(F).Thebrushretainer

markedwithblackinkmustbeplacedtothemiddle

of the sweeper.

STEP 1 - REMOVE PARTS FROM CARTON

• Toprotectpaintedparts,laythemoncardboardora

mat.

• Removethesweeperhousing,theloosepartsand

thehardwarepackagefromthecarton.Layoutthe

partsandhardwareasshownonpages3and4.

• Placethesheetofcardboardfrominsidethecarton

ontoyourworksurfacetopreventscratchingthe

sweeper.

FIGURE 1

FIGURE 3

NYLOCK NUT (F)

BRUSH

RETAINER

MARKED

BLACK

OVERLAP

BRISTLES

HEX BOLT (D)

WELDED BRACE

STEP 3: (SEE FIGURE 2)

• Tipthesweeperforwardtoaccessthebrushshaft.

FIGURE 2

STEP 4: (SEE FIGURE 3)

IMPORTANT:Besuretheoverlapbristlesfaceoutwhen

abrushisrotatedtothebottomposition.

6

STEP 5: (SEE FIGURE 4)

• Attachthebrushassemblywiththeredbrushretainer

totheleftendofthebrushshaftusingtwohexbolts

(D)andnylocknuts(F).Thebrushretainermarked

withredinkmustbeplacedtothemiddle of the

sweeper.

• Turnawheeltorotatethebrushes.(Thewheels

drivethebrushesinonedirectiononly.)Theoverlap

bristlesshouldbeonthebacksideofthebrushasit

rotates.

FIGURE 4

STEP 6: (SEE FIGURES 5 AND 6)

• Thehitchtubesarestampedwitha"77L"forthe

lefttubeanda"76R"fortherighttube.Thesweeper

housingismarkedwithan"L"ontheleftwithside

andan"R"ontherightside.

• Holdthelefthitchtubeagainsttheleftsideofthe

sweepersothatthe"77L"onthetubefacesaway

fromthesweeper.Attachthehitchtubeusingtwohex

bolts(C)andnylocknuts(G).Do not tighten yet.

HEX BOLT (C)

HITCH TUBE (L.H.)

NYLOCK NUT (G)

TUBE

MARKED

“77L”

HOUSING

MARKED “L”

FIGURE 5

FIGURE 6

HEX BOLT (C)

HITCH TUBE (R.H.)

NYLOCK NUT (G)

TUBE

MARKED

“76R”

HOUSING

MARKED “R”

STEP 7: (SEE FIGURE 6)

• Holdtherighthitchtubeagainsttherightsideofthe

sweepersothatthe"76R"onthetubefacestoward

thesweeper.Attachthehitchtubeusingtwohexbolts

(C)andnylocknuts(G).Do not tighten yet.

HEX BOLT (D)

NYLOCK NUT (F)

BRUSH RETAINER

MARKED RED

STEP 8: (SEE FIGURE 7)

• Fastenthehitchtubestogetherusingtwohexbolts

(A)andnylocknuts(G).Do not tighten yet.

HEX BOLT (A)

NYLOCK NUT (G)

FIGURE 7

7

FIGURE 9

STEP 10b: (SEE FIGURE 9)

• Ifthetractorhitchis10"ormoreabovetheground,

assemblethehitchbracketsasshowningure10.

Inserttwohexbolts(B)throughthebrackets,with

therearhexboltbetweenthecrossboltsinthehitch

tubes.Securethehexbolts(B)withtwonylocknuts

(G).Do not tighten yet.

• Assemblethetwospacers(I)ontothehitchpin(N)

andsecurethepinwiththehairpincotter(M).

FIGURE 8

STEP 10a: (SEE FIGURE 8)

• Ifthetractorhitchislessthan10"abovetheground,

assemblethehitchbracketsasshowningure9.

Inserttwohexbolts(B)throughthebrackets,with

therearhexboltbetweenthecrossboltsinthehitch

tubes.Securethehexbolts(B)withtwonylocknuts

(G).Do not tighten yet.

• Assemblethetwospacers(I)ontothehitchpin(N)

andsecurethepinwiththehairpincotter(M).

STEP 9

• Usethemarkalongthesideofthispagetomeasure

theheightofthetractorhitch.Themarkis10"from

thebottomofthepage.Ifthetractorhitchislessthan

10"abovetheground,gotoSTEP 11a. If the tractor

hitchis10"ormoreabovetheground,gotoSTEP

11b.

STEP 11

• Tightenthefourboltsassembledinsteps6and7.

• Tightenthetwoboltsassembledinstep9.

• Tightenthetwoboltsassembledinstep11aor11b.

10"

NYLOCK NUTS (G)

HITCH BRACKET

ASSEMBLY

BENT HITCH

BRACKET

HEX BOLTS (B)

HITCH PIN (N)

HAIRPIN COTTER (M)

SPACERS (I)

NYLOCK NUTS (G)

BENT HITCH

BRACKET

HITCH

BRACKET

ASSEMBLY

HEX BOLTS (B)

SPACERS (I)

HAIRPIN

COTTER (M)

HITCH PIN (N)

8

ASSEMBLY OF HOPPER BAG

STEP 12: (SEE FIGURE 10)

• Fittheendsofthetwoupperhoppertubesintothe

endsofarearhoppertube.Aligntheholesinthe

endsofthetubesandsecuretheminplaceusingtwo

curvedheadbolts(E)andnylocknuts(F).

• Fittheendsofthetwolowerhoppertubesintothe

endsofarearhoppertube.Aligntheholesinthe

endsofthetubesandsecuretheminplaceusingtwo

curvedheadbolts(E)andnylocknuts(F).

NOTE:Eithersideoftherearhoppertubecanfaceup.

FIGURE 10

FIGURE 11

UPPER

HOPPER

TUBE

HOPPER

BAG

BOTTOM

STITCHED SLEEVE

FIGURE 12

LOWER HOPPER TUBE

HOPPER BAG

BOTTOM

UPPER HOPPER

TUBE

CLEVIS PIN (L)

HAIR COTTER

PIN (M)

UPPER

HOPPER

TUBE

NYLOCK

NUT (F)

CURVED HEAD

BOLT (E)

REAR

HOPPER

TUBE

LOWER

HOPPER TUBE

REAR

HOPPER

TUBE

NYLOCK

NUT (F)

CURVED HEAD

BOLT (E)

STEP 13: (SEE FIGURE 11)

• Unfoldthehopperbag,reversethefoldofthemesh

windscreenandthenlaythebagoutatwiththe

wind screen on top.

• Inserttheendsoftheassembledupperhoppertubes

downthroughthestitchedsleevesinthesidesofthe

hopperbagandthenslidethetubesbackunderneath

the wind screen.

STEP 14: (SEE FIGURE 12)

• Placetheassembledlowerhoppertubesintothe

bottomofthehopperbagandthenslidethetubesto

thebackofthebag.

• Attachtheendsofthelowerhoppertubestothe

insideoftheupperhoppertubesusingtwoclevis

pins(L)insertedfromtheinside,andtwohaircotter

pins(M).

9

STEP 17: (SEE FIGURE 15)

• Foldthebagapsaroundthelowerhoppertubesand

attachtothebagbottomusingthesnaps.

FIGURE 15

STEP 15: (SEE FIGURE 13)

• Insertthebagframestrapintothestitchedsleeveat

thefrontedgeofthebagbottom.

FIGURE 14

SNAP FLAP

BAG FRAME STRAP

STITCHED

SLEEVE

STEP 16: (SEE FIGURE 14)

• Assemblethebagframestraptotheholesinthe

lowerhoppertubesusingtwoclevispins(K)andhair

cotterpins(M).

FIGURE 13

STEP 18: (FIGURE 16)

IMPORTANT: Do notoverbendthesupportrods

duringthefollowingstep.Overbendingwillcausethe

steel rods to loose supporting tension.

• Tipthehopperontoit'sbacktoassemblethetwo

hoppersupportrods.Placetheendsofeachrodinto

theupperandlowerrearhoppertubes,bendingthe

rodjustenoughtotintotheholesinthetubes.

SUPPORT

RODS

FIGURE 16

CLEVIS PIN (K)

HAIR COTTER

PIN (M)

BAG FRAME STRAP

10

FIGURE 18

STEP 19: (SEE FIGURE 17)

• Slidetheendofthepivotrodthroughtheupper

hoppertube.Placeabagarmtubeontotherod.Slide

therodthroughthestitchedsleeveatthefrontedge

ofthewindscreen,andthenplaceanotherbagarm

tubeontotherod.Slidetherodthroughtheother

upperhoppertube.

STEP 22: (SEE FIGURE 20)

• Toattachthehopperbagtothesweeper,slidethe

endsofthebagarmtubesintotheendsofthehitch

tubesandsecurewithtwoclevispins(J)andhairpin

cotters(M).

STEP 21: (SEE FIGURE 19)

• Secure the rope to the center of the upper rear

hoppertube.

FIGURE 20

STEP 20: (SEE FIGURE 18)

• Assembleavinylcap(O)ontoeachbagarmtube.

• Assembletwopalnuts(H)ontotheendsofthepivot

rod using a hammer.

HINT: Toeaseassemblyofthepalnuts,placethebag

onitssideonasolidsurface.Withthebottomendofthe

pivotrodagainstthesurface,tapapalnutontothetop

end of the rod. Repeat for other end of rod.

FIGURE 17

FIGURE 19

BAG ARM TUBE

HOPPER BAG

PIVOT ROD

MOUNTING CLAMP MOUNTING CLAMP

WIND SCREEN WIND SCREEN

MOUNTING CLAMP MOUNTING CLAMP

PALNUT (H)

CAP (O)

CLEVIS PIN (J)

BAG ARM TUBE

HAIRPIN

COTTER (M)

11

ATTACHING SWEEPER HITCH TO TRACTOR

BLACK LINE IS TRACTOR HITCH

HITCH BRACKET MOUNTED

BELOW HITCH TUBES

BLACK LINE IS TRACTOR HITCH

HITCH BRACKET MOUNTED

ABOVE HITCH TUBES

FIGURE 21

• Placethetractorandsweeperonaatlevelsurface.

• Setthesweeperheightadjustmenthandletoabout

themiddleofitsadjustmentrange.

• Attachthesweeperhitchtothetractorhitch,

arrangingthe3/4"spacersinoneofsixpossible

combinationsasshowninGROUPAandGROUPB

diagramsbelow.

IMPORTANT:Toobtainthebestperformancefromyour

sweeper,arrangethespacerssothatthesweeperbagis

approximatelylevelwiththegroundandapproximately5"

to7"offthegroundasshowningure21.

GROUP "B" - For vehicles with hitches

having 10" to 13" ground clearance.

GROUP "A" - For vehicles with hitches

having 8" to 10" ground clearance.

APPROXIMATELY LEVEL

(5" to 7" FROM SURFACE)

BRUSH HEIGHT ADJUSTED

APPROXIMATELY MID-WAY

12

KNOW YOUR SWEEPER

CAUTION:Keepsweeperawayfromre.

Excessiveheatcandamagethebrushesand

hopperbagandcouldcausethebagandits

contentstoburn.

CAUTION: Never attach the hopper rope

toanypartofyourbodyorclothing!Never

hold onto the rope while towing the sweeper!

Attach the ropetothetowingvehicletokeep

it away from wheels and rotating parts.

DUMPING OF SWEEPER

• Yoursweepercanbedumpedeasilywithoutgetting

off of the rider or tractor. Simply pull the rope forward

todumpthehopper.Alwaysemptyhopperaftereach

use.

BRUSH HEIGHT ADJUSTMENT

• Toadjustyoursweeperbrushestothebestoperating

height,loosenthewingknobandpushdownonthe

heightadjustmenthandletoraisethebrush,orpush

uponthehandletolowerthebrush.Bestadjustment

iswhenthebrushsettingis1/2"downintothegrass.

Alwaysmowthegrasstoanevenheightbefore

sweeping.

SWEEPING SPEED

• Tryastartingspeedofapproximately3m.p.h.(third

gearonmosttractors).Dependingontheconditions,

itmaybenecessarytoadjustthesweepingspeedin

ordertoachievebestresults.

OPERATION

HopperBag   Collectsgrassclippings,leavesanddebris.

HopperRope   Permitsdumpingofhopperbagfromdriver'sseat.

Windscreen   Helpspreventcollectedmaterialfrombeingblownoutofhopperbag.

BagArmTubes   Connectsthehopperbagtothesweeperhousing.

PivotRod   Allowshopperbagtotiltforwardtodumpmaterial.

HeightAdjustmentHandle Adjuststheoperatingheightofthesweeper.

HitchBracket   Connectsthesweepertothetowingvehicle.Adjustsforvariousheighttractorhitches.

WingKnob   Tightensthewheelinpositionafteradjustingheight.

HOW TO USE YOUR SWEEPER

HOPPER BAG

WINDSCREEN BAG ARM TUBE

PIVOT ROD

HEIGHT

ADJUSTMENT

HANDLE

HITCH

BRACKETS

HOPPER

ROPE

WING KNOB

13

MAINTENANCE

 MAINTENANCESCHEDULE

Fill in dates as you

 completeregularservice.

 Checkforloosefasteners   X

 Checkforwornordamagedparts   X   X

 Clean,inspect&lubricatewheelbearings    X

 CleanSweeper    X   X

 Clean,inspect&lubricategears      X 

FIGURE 23

CLEANING

• Cleansweeperhousingwithasoftbrushorcloth.

• Cleandebrisfromhopperbagwithabrushorbroom.

• Removeanymaterialwhichhaswrappedaround

brushesorendsofbrushshaft.

CUSTOMER RESPONSIBILITIES

• Read and follow the maintenance schedule and the

procedures listed in the maintenance section.

Before each use

Aftereachuse

Twiceayear

Everyyear

Before storage

ServiceDates

SCHEDULED MAINTENANCE

• Cleanthesweeperaftereachuse.

• Inspectforwornordamagedparts,suchasbrushes

and wheels.

• Everyyear,removethewheelsandcleanthegear

teethandtheteethonthebacksideofthewheel.

Aftercleaning,lubricatetheaxle,andtheteethon

the gears and the wheel with a light coat of grease.

Toremovetherightwheel,unscrewthewingknob

andremovethewheelandwashers.Toremovethe

leftwheel,popoffthehubcapusingascrewdriver

andremovewheelalongwiththebolt,washers,step

spacerandnut.Seegures22and23.

FIGURE 22

• Cleanthesweeperandhopperbagthoroughlyto

helppreventrustandmildew.

• Tocollapsethehopperbagforstorage,removethe

two hopper support rods from the rear of the hopper.

• Store in a dry area.

CAUTION: Before storing the

sweeper,alwaysemptythehopperbagto

avoidspontaneouscombustion.

STORAGE

WASHER

WING KNOB

REMOVING RIGHT SIDE WHEEL

BOLT

WASHER

HUB

CAP

WASHER

STEP

SPACER

NYLOCK

NUT

REMOVING LEFT SIDE WHEEL

14

GEAR AND PAWL SERVICE

IMPORTANT: Do notremovebothwheelsatthesame

timetoavoidmixingofparts.(TheR.H.andL.H.pinion

gearsarenotinterchangeable.)Make notes on the

positionofwashersandsnapringsduringdisassembly.

• Removeonewheelatatime,followingtheinstructions

intheMAINTENANCEsection.

• Removetheretainingringswhichholdthegearson

thebrushshaftandthejackshaft.

• Removethepiniongear,washeranddrivepinfromthe

endofthebrushshaft.(Thedrivepinmayfalloutofthe

brushshaftwhenthepiniongearisremoved.)

• Removetheidlergearandwashersfromthejackshaft.

• Cleanallparts.

• Replace worn parts.

• Toreassemble,lightlygreasethejackshaftandthe

brushshaft.Insertthepinintotheholeinthebrush

shaft.Makesurethepinstaysintheshaft.

• Lightlygreasetheteethonbothgearsandllthe

recessofthepiniongearwithgrease.Assembleboth

gearsbackontotheshafts.

• Lightlygreasetheaxleandthenreassemblethewheel

ontoit.Thebrushesshouldrotateonly during forward

rotationofthewheel.Ifthebrushesaredriven(rotated)

bybothforwardandreverserotationofthewheel,the

drivepinisjamminginthepiniongear.Disassemble

andcleanandlubricatethedrivepinandpiniongear.

BRUSH REPLACEMENT

NOTE: Brushreplacementshouldbedoneonebrushat

a time.

• Removethehopperbagfromthesweeper.

• Loosenthehexboltsandlocknutsontwosingle

brushretainerswhichclamponebrushtothedouble

brushretainers.Do Not loosenorremovethebolts

whichfastenthedoublebrushretainerstothebrush

shaft.Seegure24.

• Slidethebrushoutoftheretainers,notingonwhich

sideofthebrushthebristlesoverlap.Seegure24.

• Installnewbrush,makingsurethebristlesoverlapon

thesamesideofthebrushasbefore.Seegure24.

FIGURE 25

BRUSH ROTATION

BRUSH ROTATION

OVERLAP

BRISTLES

OVERLAP

BRISTLES

SINGLE

BRUSH

RETAINERS

DOUBLE BRUSH RETAINER

BRUSH

SHAFT

FIGURE 24

• Brushessettoolow.

• Brushesarejammed

• Wheelsarejammed.

Wheels skid when sweeping. • Adjustheighttillbrushesare1/2"

down into grass.

• Stopsweeper.Removeobstruction.

• Removeonewheelatatimetocheck

forobstructionordamage.Referto

ServiceandAdjustmentssection.

SERVICE AND ADJUSTMENTS

TROUBLESHOOTING

IDLER

GEAR

WASHER WASHER

RETAINING

RING

WASHER

PINION

GEAR

DRIVE

PIN

15

NOTES

16

REPAIR PARTS

486.242223 42" HIGH SPEED LAWNSWEEPER

1

2

3

4

5

6

7

8

10

11

12

14

13

13

15

16

17

21

20

20

19

18

22 23

26

25 26

22 27

29

28 27

30

32

31

33

41

33

33

42

43

33

41

33

33

41

33

41

44

46

46

46

46

46

46

46

47

47

45

48

48

49

49

51

53

54

54

51

55

55

56

56

59

58

52

52

60

61

50

17

50

17

57

57

7

37

38

19

39

40

35

34

36

Toorderreplacementparts,callSearsPartsDirect1-800-252-1698orgotowww.searspartsdirect.com

17

ITEM PART NO. QTY DESCRIPTION

1 67105 1 HousingAssembly

2 68202 1 HeightAdjustmentTubeAss'y.

3 46776 1 HitchTube,R.H.

4 46777 1 HitchTube,L.H.

524192 1 Bracket,Hitch(Straight)

6 23687 1 Bracket,Hitch

7 41436 2 Wheel&TireAss'y.(withbearings)

841570 2 DustCover

9 67103 1 WheelDriveAssembly,L.H.(Not

Shown)

10 67102 1 WheelDriveAssembly,R.H.

11 27235 1 Brush Shaft

12 46780 4 Brush,42"

13 23581 8Retainer,Brush(Single)

14 23580 4 Retainer,Brush(Double)

15 43661 4 Bolt,Hex1/4-20x1"Lg.

16 43012 8Bolt,Hex1/4-20x3/4"Lg.

17 47189 16 Nut,Nylock1/4-20Thread

18 43720 1 WingKnob

19 141 2 Washer,.378x1.25x.061

20 45088 4 Wheel Bearing

21 44008 2 Washer,1-1/8"x.78"x.025"

22 1650-1 4 Ring,Retaining(E-type)

23 48652 1 Gear,PinionR.H.

24 48651 1 Gear,PinionL.H.(notshown)

25 47046 2 DowelPin(Drive)

26 R19212016 4 Washer,.656x1.25x.025

27 44137 4 Washer,1/2"x1"x.02"

28 41434 2 IdlerGear,27T.

29 23520 2 Spacer,.660IDx.250ODx.25

30 44232 2 Ball Bearing

31 41437 2 Bearing Retainer

ITEM PART NO. QTY DESCRIPTION

32 43182 4 Bolt,Hex5/16-18x3/4"Lg.

33 47810 12 Nut,Nylock5/16-18Thread

34 27234 1 Retainer,CarriageBolt

35 42425 1 Bolt,Carriage5/16-18x3-1/2"

36 43943 1 Grip,HeightAdjust

37 41017 1 HubCap

38 43932 1 Bolt,Hex3/8-24x3-1/2"Lg.

39 26538 1 Spacer, Step

40 1038 1 Nut,Nylock3/8-24Thread

41 43084 4 Bolt,Hex5/16-18x1-3/4"Lg.

42 46782 2 Bolt,Hex5/16-18x3"Lg.

43 43224 2 Bolt,Hex5/16-18x2-1/4"Lg.

44 23353 1 Pin,Hitch

45 23368 2 Tube,HitchSpacer

46 43055 7 HairpinCotter,3/32"#3

47 46867 2 Pin,Clevis1/4"x1-1/2"Lg.

48 48365 2 Pin,Clevis1/4"x1-1/8"

49 48366 2 Pin,Clevis3/8"x1/2"

50 43978 4 CurvedHeadBolt,1/4-20x1"

51 44917 2 Palnut,3/8"

52 44481 2 Cap,Vinyl

53 46823 1 PivotRod,HopperBag

54 49766 2 Tube,BagArm

55 47477 2 Tube,RearHopperFrame

56 48726 2 Tube,LowerHopperFrame

57 49765 2 Tube,UpperHopperFrame

58 43938 2 HopperSupportRod

59 24189 1 Strap, Bag Frame

60 49768 1 HopperBag

61 43737 1 HopperRope

41900 1 OwnersManual

REPAIR PARTS

486.242223 42" HIGH SPEED LAWNSWEEPER

Toorderreplacementparts,callSearsPartsDirect1-800-252-1698orgotowww.searspartsdirect.com

18

19

Toorderreplacementparts,callSearsPartsDirect1-800-252-1698

or go to www.searspartsdirect.com