Craftsman 486 245992 Operators Manual
486245992 486245992 CRAFTSMAN FRONT BUMPER - Manuals and Guides L0904377 View the owners manual for your CRAFTSMAN FRONT BUMPER #486245992. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman FRONT BUMPER Manual
CRAFTSMAN Accessories, Tractor Manual L0904377 CRAFTSMAN Accessories, Tractor Owner's Manual, CRAFTSMAN Accessories, Tractor installation guides
486.245992 L0904377
2015-01-05
: Craftsman Craftsman-486-245992-Operators-Manual-160922 craftsman-486-245992-operators-manual-160922 craftsman pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Owner's Manual ® F NT U IE Model No. 486.245992 Fits 917 Series LT/YT/GT Tractors / / / CAUTION: ,, ,, ,, ,, ,, Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT Safety Assembly Operation Maintenance Parts - READ THIS FIRST!!! For Missing Parts or Assembly Please Call 866-576-8388 Questions Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.craftsman.com PRINTED IN U.S.A. FORM NO. 49789 (REV. 9/05) ONEYEAR LIMITED WARRANTY When operated and maintained according to the instructions supplied with it, if this Tractor Brush Guard fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ® to arrange for free repair. If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. TOOLS REQUIRED (2) 9/16" Wrenches (Socket wrench may be used) Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. Identify and lay out parts listed above. Not all hardware will be used. Unused parts may be discarded after assembly. Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179 Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Refer to your tractor owners manual for "Rules For Safe Operation". SINGLE ROD DECK SUSPENSION TRACTORS iMPORTANT: If your tractor has a mower deck suspension bracket located under the middle of the front axle as shown in figure 1, continue with the instructions on page 3. If your tractor does not have a mower deck suspension bracket like the one shown go to page 4. Look for this symbol to point out important safety precautions. It means -- Attention!! Become alert!! Your safety is involved. I ------[-q ! T-t HARDWARE - FULL SIZE 11 A __B _ ........ C / BRACKET FIGURE 1 Ref. No. Part No. Qty. A 48894 2 B C D E F 43062 43001 HA21362 44742 43003 64798 2 4 4 2 4 1 Description Self Threading Bolt, 3/8-16 x 1-1/2" Hex Bolt, 3/8-16 x 1-1/2" Hex Bolt, 3/8-16 x 1" Hex Nut, 3/8-16 Plug Lock Washer, 3/8" Bumper VIEWED FROM FRONT CAUTION!Muffleris hot!Allowengineto cool downbeforeproceedingwith bumper installation. STEP 1 : (SEE FIGURE 2) • Remove tractor hood. (Refer to tractor manual.) Remove the browning shield as shown below. STEP 4: (SEE FIGURE 5) Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. The bumper has three mounting holes. The rear hole provides the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for hood to stay in raised position when opened. Insert a hex bolt (C) through tractor frame and into desired mounting hole on each side of bumper and secure with a hex nut (D). IMPORTANT: Before fully tightening nuts, be sure tractor hood will stay in raised position when opened. REMOVE FRONT SCREWS REMOVE BROWNING SHIELD FIGURE 2 STEP 2: (SEE FIGURE 3) Insert a hex bolt (C) into the second mounting hole from the front of the tractor frame and fully tighten a hex nut (D) onto the bolt. Repeat on other side of tractor. FIGURE 5 HEX BOLT (C) \ HEX NUT (D) FIGURE STEP 5: (SEE FIGURE 6) • Replace the browning shield using the front screws you removed in Step 1. 3 STEP 3: (SEE FIGURE 4) • Place plug (E) on a work bench or solid table and push end of bumper down onto plug. Repeat for second plug. REPLACE FRONT SCREWS BUMPER REPLACE PUSH DOWN WiTH EVEN PRESSURE WORK BENCH OR SOLID TABLE__ _=_.___.__ FIGURE 4 BROWNING FIGURE 6 SHORT STEP PLUG (E) SHIELD DUAL ROD DECK SUSPENSION TRACTORS STEP 2: (SEE FIGURE 2) • IMPORTANT: These instructions are for tractors with dual mower deck suspension brackets like the examples shown in figure 2 on this page.. CAUTION! Muffler is hot! Allow engine to cool down before proceeding with bumper installation. IMPORTANT: Be sure to re-attach shield after bumper is installed. muffler and heat If rear mounting holes in tractor frame are empty, install hex bolts (C) and hex nuts (D) supplied in parts bag. See figure 2. STEP 1: (SEE FIGURE 1) * * Remove any bolts present in front mounting holes in side of tractor frame, if bolt will not screw out of hole, check if a nut is present on bolt on inside of frame. On GT tractors, if access to nut is blocked by a front mounted muffler, slide muffler down exhaust tubes to rest on top of browning shield. Remove tractor hood. (Refer to tractor manual.) Remove an (LT) Lawn Tractor heat shield like the one shown. Remove a (GT) Garden Tractor heat shield like the one shown only if you need access to inside of tractor frame during step 2. (LT) LAWN TRACTOR REMOVE BOLT iF PRESENT iNSTALL (C), (D) iF HOLE IS EMPTY IMPORTANT: Be sure to re-attach the heat shield after bumper is installed. (LT) LAWN TRACTOR SUSPENSION BRACKET REMOVE THIS STYLE HEAT SHIELD (LT) LAWN TRACTOR REMOVE BOLT iF PRESENT (GT) GARDEN iNSTALL (C), (D) iF HOLE iS EMPTY SUSPENSION BRACKET TRACTOR (GT) GARDEN REMOVE THIS HEAT SHIELD ONLY iF MUFFLER MUST BE MOVED iN STEP 2. TRACTOR EXHAUST TUBES FIGURE 1 FIGURE 2 4 STEP 3: (SEE FIGURE 3) * Place plug (E) on a work bench or solid table and push end of bumper down onto plug. Repeat for second plug. See figure 1. BUMPER PUSH DOWN WiTH EVEN PRESSURE WORK BENCH OR SOLID TABLE FIGURE SHORT STEP "__ PLUG (E) 3 STEP 4: (SEE FIGURE 4) * * Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. The bumper has three mounting holes. The rear hole provides the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for hood to stay in raised position when opened. Attach the bumper using either standard hex bolts (B) and hex nuts (D) or self threading bolts (A) and lock washers (F). Use the self threading bolts (A) if standard hex bolts (B) do not insert freely into the hole in the tractor frame. iMPORTANT: Before fully tightening bolts, be sure tractor hood will stay in raised position when opened. LAWN TRACTOR (LT) SHOWN GARDEN TRACTOR (GT) iS SiMiLAR HEX NUT (D) FORBOLT(B) (F) FORBOLT(A) BOLT(A) or (8) FIGURE 4 NOTES NOTES Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night (U.S.A. and Canada) www.sears.com www.sears.ca Our Home For repair of carry-in items like vacuums, lawn equipment, and electronics, call or go on-line for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Call anytime, day or night (U.S.A. only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-827-6655 (U.S.A.) 1-800-361-6665 Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR Au Canada / MD Marque depos6e de Sears Mc (1-800-533-6937) www.sears.ca ® Registered Trademark / TM Trademark / SMService Mark of Sears Brands, LLC ® Marca Registrada / TN Marca de Fabrica / SM Marca de Servicio de Sears Brands, de commerce pour service en fran£ais: 1-800-LE-FOYER ® (1-888-784-6427) MC Marque (Canada) Brands, LLC LLC © Sears Brands, LLC
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Sun May 03 04:13:34 2009 Author : Title : Subject :EXIF Metadata provided by EXIF.tools