Craftsman 486 24621 Operators Manual
CRAFTSMAN Accessories, Tractor Manual L0303050 CRAFTSMAN Accessories, Tractor Owner's Manual, CRAFTSMAN Accessories, Tractor installation guides
486.24621 L0303050
2015-01-05
: Craftsman Craftsman-486-24621-Operators-Manual-160917 craftsman-486-24621-operators-manual-160917 craftsman pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Owner's Manual I (RAFTSMANI TRACTOR BRUSH GUARD Model No. 486.24621 CAUTION: • • • • • Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT - READ THIS For Missing Parts or Assembly Please Call 217-728-8388 Safety Assembly Operation Maintenance Parts FIRST!!! Questions Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. Sears, Roebuck and Co., Hoffman www.sears.com/craftsman PRINTED IN U.S.A. Estates, IL 60179 U.S.A. FORM NO. 48748 (1/03) Any power equipment can cause injury if operated improperly or if the user does not understand the equipment. Exercise caution at all times, when using power equipment. • Refer to your tractor owners For Safe Operation". ,_ manual for "Rules Look for this symbol to point out important safety precautions. Become alert!! Your safety is involved. FULL SIZE HARDWARE how to operate CHART CARTON It mean--Attention!! CONTENTS 1. L.H. Mounting Bracket 2. R.H. Mounting Bracket 3. Bumper #25037 #25038 #64614 3 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED (2) 9/1 6" Open End or Box Wrenches Ref. No. Part No. Qty. A 48894 2 B C D E F G H I 43062 43001 45091 44742 43055 48866 43003 43070 2 2 2 4 2 1 4 4 & Description Self Threading Screw, 3/8-16 x 1-1/2" Hex Bolt, 3/8-16 x 1-1/2" Hex Bolt, 3/8-16 x 1" Clevis Pin, 3/8" x 1" Plug Hair Cotter Pin, 3/32" Pivot Spacer Lock Washer, 3/8" Washer, 3/8" CAUTION! Muffler is hofl Allow engine to cool down before proceeding with bumper installation. Place a plug on a work bench or solid table. Set end of bumper onto plug until it rests on short step of plug. Using even pressure, push down on bumper until end of bumper slips over plug. Assemble all four plugs. See figure 1. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH OR SOLID TABLI, FIGURE 1 2 .=............j,SHORT STEP _--- PLUG IMPORTANT: To help avoid misalignment of holes in tractor frame, lower the mower deck to the ground or disconnect it from the front brackets before removing any bolts from the tractor frame. Front mower suspension brackets for both GT and LT tractors are shown in figure 2. Use a bumper mounting bracket to help identify the correct mounting holes. • Lower the mower deck to the ground. • Remove bolts on both sides of the tractor from two holes shown in figure (GT) FRAME 2. (LT) FRAME o Insert a pivot bushing into the rear hole in the bumper. Align the rear hole in the bumper with the middle hole in the L.H. mounting bracket and assemble a 3/8" x 1-1/2" hex bolt, a 3/8" lock washer and a 3/8" flat washer. Repeat on the R.H. side, then tighten both bolts. See figure 4. NOTE: Use the 3/8" x 1-1/2" self threading screw in place of the hex bolt if there was no bolt in the front hole in the tractor frame and the hole is too small. Insert a 3/8" x 1" clevis pin into the front hole in the bumper and the front hole in the mounting brackets. Secure the clevis pins with 3/32" hair cotter pins. See figure 4. IMPORTANT: Before raising the tractor's hood, you must first remove the clevis pins and lower the bumper down against the bumper stops on the L.H. and R.H. mounting brackets. REMOVE BOLTS FROM THESE HOLES 3/8" FLAT WASHER PIVOT SPACER FIGURE 2 F_ 3-/8"LOCK WASHER Assemble the L.H. mounting bracket to the front left side of the tractor frame. Fasten to the rear hole using a 3/8" x 1" hex bolt, a 3/8" lock washer and a 3/8" flat washer. Align the middle hole in the mounting bracket with the hole in the tractor frame. Tighten the bolt enough to hold the bracket in place. Repeat for the R.H. mounting bracket. See figure 3. FLAT WASHER L.H. MOUNTING BRACKET 3/8" x 1" HEX BOLT LOCK WASHER ! 3132"HAIR COTTER PIN FIGURE 5 / ALIGN THESE HOLES / FIGURE 3 3/8"x 1" CLEVIS PIN For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sMAnytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center .................. 1-800-488-1222 Anytime, day or night www.sears.com For the replacement parts, accessories and owner's manuals that you need to do-it-yourself, call Sears PartsDirect sM! 1-800-366-PART 6 a.m.- (1-800-366-7278) 11 p.m. CST, 7 days a week www.sears.com/partsdirect To purchase or inquire about _ Sears Service Agreement: 1 800 827 6655 7 a.m.- 5 p.m. CST, Mort.- Para pedir servicio de reparacion a domicilio y para ordenar piezas con entrega a domicilio: :; 1-888-SU-HOGAR : Sat. Au Canada pour serv ce en fran£a s sM 1-877-LE-FOYER sM ( 1-877 -533-693 7 ) (1-888-784-6427) [ HomeCentral j ® Registered ® Sears, Roebuck and Co. ® Marca Trademark Registrada / TM / TM Marca Trademark de F&brica of Sears, de Sears, Roebuck Roebuck and and Co. Co.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 4 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Aug 14 15:29:47 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools