Craftsman C3 19 2 Volt Jig Saw With Laser Trac Owners Manual

2015-03-28

: Craftsman Craftsman-C3-19-2-Volt-Jig-Saw-With-Laser-Trac-Owners-Manual-659630 craftsman-c3-19-2-volt-jig-saw-with-laser-trac-owners-manual-659630 craftsman pdf

Open the PDF directly: View PDF PDF.
Page Count: 28

Save this manual for future reference
Guarde este manual para futuras consulta
19.2 VOLT CORDLESS JIG SAW
VARIABLE SPEED/ORBITAL
SIERRA DE VAIVÉN
INALÁMBRICA DE 19,2 V
VELOCIDAD VARIABLE/ORBITAL
Model No.
315.115690
Número de modelo
315.115690
983000-920
8-31-10 (REV:04)
WARNING: To reduce the risk of injury,
the user must read and understand the
operator’s manual before using this
product.
Customer Help Line: 1-800-932-3188
Teléfono de atención al consumidor: 1-800-932-3188
Sears Brands Management Corporation, 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
Visite el sitio web de Craftsman: www.sears.com/craftsman
OPERATOR’S MANUAL
MANUAL DEL OPERADOR
BATTERIES AND CHARGERS
SOLD SEPARATELY
LAS BATTERÍAS Y LOS CARGADORES
SE VENDEN POR SEPARADO
ADVERTENCIA: Para reducir el
riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
2
ENGLISH
Warranty ...................................................................... 2
Introduction ................................................................. 2
General Safety Rules .............................................. 3-4
Specific Safety Rules .............................................. 4-5
Symbols ......................................................................6
Features ......................................................................7
Assembly ....................................................................8
Operation .............................................................. 9-11
Adjustments ..............................................................11
Maintenance .............................................................12
Accessories...............................................................12
Illustrated Parts List ..................................................13
Figure numbers (illustrations) ................................... i-iii
Parts Ordering / Service.............................. Back Page
TABLE OF CONTENTS / ÍNDICE DE CONTENIDO
WARRANTY / GARANTÍA
INTRODUCTION / INTRODUCCIÓN
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Esta herramienta ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
ESPAÑOL
Garantía ......................................................................2
Introducción ................................................................2
Reglas de seguridad generales .............................. 3-4
Reglas de seguridad específicas ............................ 4-5
Símbolos .....................................................................6
Características ............................................................7
Armado .......................................................................8
Funcionamiento .................................................... 9-11
Ajustes ......................................................................11
Mantenimiento ..........................................................12
Accesorios ................................................................12
Figura numeras (ilustraciones) ................................. i-iii
Pedidos de piezas / Servicio ................. Pág. posterior
CRAFTSMAN® ONE YEAR LIMITED WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship.
With proof of purchase, defective product will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the web site: www.craftsman.com
This warranty does not cover the blades, which are expendable parts that can wear out from normal use within the war-
ranty period.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
* * *
GARANTÍA LIMITADA DE CRAFTSMAN POR UN AÑO
Este producto tiene garantía por cualquier defecto en material o mano de obra DURANTE UN AÑO desde la fecha de
compra. Los productos defectuosos se remplazarán sin cargo si presenta un comprobante de pago.
Si desea conocer los detalles de la cobertura de la garantía para conseguir reparaciones o recambios, visite el
sitio Web: www.craftsman.com
Esta garantía no cubre las hojas, que es una pieza fungible que puede desgastarse por el uso normal durante el período
de garantía.
La garantía pierde validez si este producto se utiliza mientras se prestan servicios comerciales o si se alquila a otra
persona.
Esta garantía le otorga derechos legales específicos y también puede gozar de otros derechos que varían según el
estado.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
3 – English
Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appro-
priate conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
Dress properly. Do not wear loose clothing or jew-
elry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry, or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly main-
tained power tools.
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury. The term “power
tool” in all of the warnings listed below refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if
your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the risk
of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
Use battery only with charger listed. For use with
19.2V nickel-cadmium and 19.2V lithium-ion battery
packs, see tool/appliance/battery pack/charger corre-
lation supplement 988000-272.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
4 – English
GENERAL SAFETY RULES
Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended could
result in a hazardous situation.
BATTERY TOOL USE AND CARE
Ensure the switch is in the off position before in-
serting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is main-
tained.
WARNING! To reduce the risk of injury, user must
read instruction manual.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the Main-
tenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with
a “live” wire will also make exposed metal parts of the
tool “live” and shock the operator.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or
damaged battery immediately.
Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
For best results, your battery tool should be
charged
in a location where the temperature is more
than 50°F
but less than 100°F. Do not store outside
or in vehicles.
5 – English
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in con-
tact with your skin, wash immediately with soap
and water. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
LASER GUIDE WARNINGS:
The laser guide radiation used in this tool is Class IIIa with
maximum <5 mW and 650nm wavelengths.
These lasers do not normally present an optical hazard
although staring at the beam may cause flash blindness.
Avoid direct eye exposure when using the laser guide.
The laser shall be used and maintained in accordance
with the manufacturer’s instructions.
Never aim the beam at a person or object other than
the workpiece.
Always ensure the laser beam is aimed at a sturdy
workpiece without reflective surfaces. Shiny reflective
sheet metal or similar shiny materials are not suitable
for laser use.
All repairs should be made by an authorized service
representative or the laser manufacturer.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this power
tool. If you loan someone this power tool, loan them
these instructions also.
SPECIFIC SAFETY RULES
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
6 – English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
No Hands Symbol Failure to keep your hands away from the blade will result in
serious personal injury.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Li - Ion Recycle Symbols
This product uses nickel- cadmium (Ni-Cd) and lithium-ion
(Li-ion) batteries. Local, state or federal laws may prohibit
disposal of batteries in ordinary trash. Consult your local waste
authority for information regarding available recycling and/or
disposal options.
V Volts Voltage
min Minutes Time
Direct Current Type or a characteristic of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
The following signal words and meanings are intended to explain the levels of risk associated with this product.
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SYMBOL SIGNAL MEANING
DANGER:
CAUTION:
CAUTION:
WARNING:
7 – English
FEATURES
PRODUCT SPECIFICATIONS
Length of Stroke ........................................................... 1 in.
Strokes Per Minute ......................................... 0-2,100/min.
Switch ..........................................................Variable Speed
Blade Clamp ........................................................... Toolless
Cutting Angle ................................0° to 45°, Left and Right
Orbital Motion ....................................................4 Positions
Laser Guide .........................Class IIIa, <5mW max, 650nm
KNOW YOUR JIG SAW
See Figure 1, page i.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual
as well as a knowledge of the project you are attempt-
ing. Before use of this product, familiarize yourself with all
operating features and safety rules.
BLADE STORAGE
When not in use, you can place the blades provided with
your orbital jig saw in the storage area located on the
back of the saw.
ERGONOMIC DESIGN
The design of the orbital jig saw provides for easy han-
dling. It is designed for comfort when operating in different
positions and at different angles.
LASER GUIDE
The laser guide will generate a red colored laser beam on
the work surface in front of the saw when turned on.
LOCK-OFF BUTTON
Your saw is equipped with a lock-off button which reduces
the possibility of accidental starting.
ORBITAL ADJUSTMENT KNOB
Choose from four orbital adjustment positions for fine to
aggressive cutting.
TOOLLESS BLADE CLAMP
Your saw has a blade clamp design that does not require
the use of a tool (blade wrench) when installing or remov-
ing the blade.
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure.
8 – English
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list
are included.
WARNING: Do not use this product if it is not
completely assembled or if any parts appear to be
missing or damaged. Use of a product that is not
properly and completely assembled could result in
serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
PACKING LIST
Orbital Jig Saw
Blade
Hex Key
Operator’s Manual
WARNING: If any parts are damaged or missing
do not operate this tool until the parts are replaced.
Use of this product with damaged or missing parts
could result in serious personal injury.
WARNING: Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the tool when assembling
parts.
9 – English
WARNING: Always remove battery pack from your
tool when you are assembling parts, making adjust-
ments, cleaning, or when not in use. Removing bat-
tery pack will prevent accidental starting that could
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 2, page i.
Lock the switch trigger by placing the rotation selector
in the center position.
Depress the latches on the side of battery pack.
Remove the battery pack from the tool.
WARNING: To prevent accidental starting that could
cause serious personal injury, always remove the bat-
tery pack from the tool when assembling parts.
TO INSTALL BLADES
See Figure 3, page i.
Remove battery pack.
Lift blade clamp lock/release lever located on front of
saw.
Insert saw blade between blade clamp and saw bar as
far as possible.
Release and lock blade clamp lever.
Replace battery pack.
BLADE SELECTION
To obtain the best performance from the saw, it is impor-
tant to select a specific blade for the particular applica-
tion and type of material you wish to cut. By doing this
you will get a smoother, faster cut and prolong blade life.
Replacement blades for this saw are available from your
nearest Sears retail. It is recommended you use a T-shank
blade. If a T-shank blade is not available, a high quality
U-shank may be used.
BLADE STORAGE
See Figure 4, page i.
A convenient feature on the saw is the blade storage
compartment. The blade storage compartment is located
on the back of the saw. It is convenient for storing extra
blades and storing blades when not in use.
To open: Push the door down with your thumb or
finger. Place blades in blade storage compartment.
To close: Push the door up with your thumb or finger.
HEX KEY STORAGE
See Figure 5, page ii.
Secure hex key on the saw base behind the rubber
covered tab. Push into place.
Make sure the hex key is secured before performing
any sawing operation.
Remove by pulling on the hex key.
WARNING: Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING: Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure to
do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
WARNING: Do not use any attachments or
accessories not recommended by the manufacturer
of this product. The use of attachments or
accessories not recommended can result in serious
personal injury.
APPLICATIONS
You may use this tool for the following purposes:
Sawing non-ferrous metal, sheet steel, wood, plastic,
and similar materials
Cutting wood surfaces
Cutting thin sheet metal
Cutting plastics and laminates
This product will accept Craftsman 19.2 V lithium-ion bat-
tery packs and Craftsman 19.2 V nickel-cadmium battery
packs.
For complete charging instructions, refer to the Operator’s
Manual for your battery pack and charger models.
BATTERY PROTECTION FEATURES
Craftsman 19.2 V lithium-ion battery packs are designed
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO INSTALL BATTERY PACK
See Figure 2, page i.
Lock the switch trigger by placing the rotation selector
in the center position.
Place the battery pack on the tool.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured on the
tool before beginning operation.
CAUTION: When placing the battery pack in the
tool, be sure raised rib on battery pack aligns with
the groove in the tool and that the latches snap into
place properly. Improper assembly of the battery
pack can cause damage to internal components.
OPERATION
10 – English
OPERATION
LASER GUIDE
See Figure 6, page ii.
Depress the laser guide switch to generate a red laser
beam on the work surface in front of the saw. Use the
laser to guide the saw along the line of cut.
LOCK-OFF BUTTON
See Figure 7, page ii.
The lock-off button is located on the handle above the
switch trigger. You must depress the lock-off button in
order to pull the switch trigger. The lock resets each time
the trigger is released.
NOTE: You can depress the lock-off button from either the
left or right side.
SWITCH TRIGGER
See Figure 7, page ii.
To turn the saw ON, depress and hold lock-off button,
then depress the switch trigger. To turn it OFF, release the
switch trigger.
GENERAL CUTTING
See Figure 7, page ii.
Rest the front of the saw base on the workpiece and
align cutting edge of the blade with the line on your
workpiece.
Start the saw and move it forward on the work surface.
Apply downward pressure to keep the saw steady
and only enough forward pressure to keep the blade
cutting.
Do not force the saw. Forcing the saw may overheat the
motor and break saw blades. Broken saw blades must be
discarded. Remove the broken portion of the saw blade
from the clamp and install a new saw blade.
WARNING: Excessive side pressure on the blade
could result in broken blades or damage to the ma-
terial being cut.
ORBITAL MOTION
See Figure 7, page ii.
The blade of the saw cuts in orbital motion. This feature is
adjustable and provides faster, more efficient cutting. The
blade cuts through your work in the upstroke but does not
drag across your work in the downstroke. The higher set-
tings should be used when fast cutting in soft material is
desired. The lower settings should be used when cutting
materials with more resistance.
STRAIGHT CUT
See Figure 7, page ii.
A straight cut can be made by clamping a piece of wood
or straightedge to the workpiece and guiding the edge of
the saw against it. Make the cut from one direction only.
Do not cut halfway and complete the cut from the oppo-
site end.
SCROLL CUTTING
See Figure 8, page ii.
Scroll cuts can be made with the jig saw by guiding the
direction of the cut with applied pressure on the handle.
ANGLE CUTTING (BEVEL CUTTING)
See Figures 9 - 10, page ii.
Bevel cutting angles may be adjusted from 0° to 45° right
or left. Angles for cuts from 0° to 45° in 15° increments
are marked on a scale on both the left and right side of
the base. Notches on the rear of the base provide posi-
tive stops at each of the above mentioned 15° increments.
A protractor is recommended when accurate cuts are
required.
Remove the battery pack.
Using the 1/8 in. hex key provided, loosen the base
pivot screws until the base can be moved.
Slide base forward until base pivot screws can move
freely in slots in base.
Align the mark, on the base, of the desired angle with
the edge of the motor housing.
Once the desired angle is reached, slide base back
until tab on motor housing aligns with the appropriate
notch on rear of base.
NOTE: When making a set-up for accurate cuts with
a protractor, or for angles other than the preset 15°
increments, the positive stop notches on the rear of the
base are not used.
Tighten the base pivot screws securely.
Return hex key to storage compartment.
Replace the battery pack.
NOTE: The wide slot in the base must be used when mak-
ing bevel cuts, scroll cuts, plunge cuts, and when cutting
metal.
PLUNGE CUTTING
See Figures 11 - 12, page ii.
WARNING: To avoid loss of control, broken blades,
or damage to the material being cut, always use
extreme caution when making plunge cuts. We do
not recommend plunge cutting on materials other
than wood.
TO MAKE A PLUNGE CUT
Mark the line of cut clearly on the workpiece.
Set the cutting angle at 0° and the orbital adjustment
knob to 0.
Drill a pilot hole though any point on the line of cut.
Using high speed, start the saw and slowly lower the
blade through the pilot hole into the workpiece until the
blade cuts through the wood.
Do not move the base forward until the blade cuts
entirely through the workpiece and the base is in
complete contact with the workpiece.
11 – English
OPERATION
Move the saw forward to complete the opening.
Use only the seven teeth per inch blade for this type of
cut.
SPLINTER-FREE CUTTING
See Figures 13 - 14, page iii.
The base of the jig saw has a narrow slot to permit
splinter-free cutting. It is especially useful when cutting
plywood. This feature should only be used when making
straight cuts or circle cuts. It is not for bevel cutting or
plunge cutting.
NOTE: The non-orbital setting also helps reduce
splintering when cutting plywood.
POSITIONING BASE IN THE SPLINTER-FREE
CUTTING POSITION
Remove the battery pack.
Using the 1/8 in. hex key provided, loosen base pivot
screws and slide base forward.
Always set the cutting angle at 0° for splinter-free
cutting. To set cutting angle at 0°, align the 0° mark on
the scale with the edge of the motor housing.
NOTE: When setting angle at 0° for splinter-free
cutting, the positive stop notches on the rear of the
base are not used.
Tighten base pivot screws securely.
Remove hex key and return it to storage compartment.
Replace the battery pack.
OPTIONAL EDGE GUIDE
See Figure 15, page iii.
An optional edge guide is available for use with the saw. It
can be used for making cross cuts and rip cuts.
Remove the battery pack.
Loosen the edge guide screw.
Insert the arm through the two slots in the base of the
saw as shown.
Adjust the edge guide to the desired width and lock in
place with the edge guide screw.
Replace the battery pack.
ADJUSTMENTS
WARNING: Use of controls or adjustments or per-
formance of procedures other than those specified
herein could result in hazardous radiation exposure.
ADJUSTING THE LASER
See Figure 16, page iii.
The laser can be realigned by adjusting the two screws
located in the front of the saw. The top screw moves the
laser beam laterally from left to right. The bottom screw
moves the laser beam in a rotational direction.
NOTE: Draw a pencil line on scrap workpiece parallel to
the long edge of the base as a straight line guide to aid in
the adjusting process.
Turn laser on.
Rest base of saw on scrap workpiece.
Adjust screws as necessary.
Since blade thicknesses vary, always make a trial cut in
scrap workpiece to ensure an accurate cut.
Check for proper alignment.
Repeat as necessary until laser is aligned.
12
MAINTENANCE
WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken or destroy plastic
which may result in serious personal injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
WARNING: Upon removal, cover the battery pack’s
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack
or remove any of its components. Lithium-ion and
nickel-cadmium batteries must be recycled or dis-
posed of properly. Also, never touch both terminals
with metal objects and/or body parts as short circuit
may result. Keep away from children. Failure to
comply with these warnings could result in fire and/
or serious injury.
WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
WARNING: Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure to
do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
WARNING: To avoid serious personal injury, always
remove the battery pack from the tool when cleaning
or performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Look for these accessories at Sears retail:
Edge Guide ..............................................................................................................................................Item No. 926320
WARNING: Current attachments and accessories available for use with this tool are listed above. Do not use
any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or
accessories not recommended can result in serious personal injury.
ACCESSORIES
13
CRAFTSMAN 19.2 VOLT CORDLESS JIG SAW – MODEL NO. 315.115690
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
The model number will be found on a label attached to the motor housing. Always mention the model
number in all correspondence regarding your CORDLESS JIG SAW or when ordering repair parts.
Key Part
No. Number Description Qty.
1 *** Wood Cutting Blade ........................ 1
*** Metal Cutting Blade (not shown) ..... 1
2 660302002 * Screw (#10-24 x 1/2 in.) .................. 2
3 630847003 Plate................................................. 1
4 660302001 * Screw (#10-24 x 3/8 in.) .................. 1
5 630846012 Base................................................. 1
6 680907001 * Hex Key (3 mm) ............................... 1
Key Part
No. Number Description Qty.
7 550432001 Rubber Tube .................................... 1
8 671314002 Blade Guard .................................... 1
9 940077089 Data Label ....................................... 1
10 940054131 Logo Label ....................................... 1
11 681070001 *Hex Key (5/64 mm - Not Shown) ..... 1
12 606551003 Edge Guide (Optional - Not Shown)
983000920 Operator’s Manual (Not Shown)
PARTS LIST
®
9
10
6
4
87
5
1
3
2
* Standard Hardware Item – May Be Purchased Locally
*** Complete assortment available at your Nearest Sears Retail Store
i
Fig. 1
A - Lock-off button (botón del seguro de apagado)
B - Switch trigger (gatillo del interruptor)
C - Toolless blade clamp (mordaza de la cuchilla
de apriete sin herramienta)
D - Saw blade (hoja de la sierra)
E - Orbital adjustment knob (perilla de ajuste
de órbita)
Fig. 3
Fig. 2
AB
EF
G
H
D
C
I
F - Saw base (base de la sierra)
G - Hex key (llave hexagonal)
H - Hex key storage (lugar de guardar la llave
hexagonal)
I - Laser guide switch (interruptor de guía láser)
®
A - Depress latches to release battery pack (para
soltar el paquete de baterías oprima los
pestillos)
B - To install (para la instalación)
C - To remove (para el desmontaje)
D - Battery pack (paquete de baterías)
E - Latches (pestillos)
A
B
C
D
E
Fig. 3
A - Lift blade clamp (levante la mordaza de la
cuchilla)
B - Blade clamp lock/release lever (palanca de
aseguramiento y afloje de la mordaza de la
cuchilla)
C - Saw blade (hoja de la sierra)
D - Blade clamp (mordaza de la cuchilla)
A
B
C
D
Fig. 4
A - Saw blade (hoja de la sierra)
B - Blade storage compartment (compartimiento
de las hojas)
A
B
ii
PELIGRO
Radiación láser –
Evite la exposición directa de los ojos.
Salida máx. <5 mW Longitud de onda: 650nm
Aparato láser Clase IIIa
Cumple con la norma
21 CFR, partes
1040.10 y 1040.11
RYLD
PELIGRO
Radiación
láser al
estar
abierto,
evite la exposición directa de los ojos.
EVITE EXPONERSE
Hay radiación láser a través de esta abertura.
Fig. 5
A - Hex key (llave hexagonal)
B - Hex key storage area (lugar de guardar la llave
hexagonal)
B
A
Fig. 6
®
A
B
A - Laser guide switch (interruptor de guía láser)
B - Laser guide (guía láser)
Fig. 7
A - Switch trigger (gatillo del interruptor)
B - Lock-off button (botón del seguro de apagado)
C - Laser guide (guía láser)
D - To increase orbital setting (para aumentar el
ajuste de la órbita)
E - To decrease orbital setting (para disminuir el
ajuste de la órbita)
F - Orbital adjustment knob (perilla de ajuste de
órbita)
A
B
C
DE
F
Fig. 8
Fig. 9
A - Base pivot screws (tornillos del pivote de la
base)
B - Saw base (base de la sierra)
C - Hex key (llave hexagonal)
A
B C
®
15
0
30
45
Fig. 10
A - Scale (indicador de la escala)
B - Saw base (base de la sierra)
A
B
®
Fig. 11
A - Pilot hole (agujero guía)
A
Fig. 12
A - Pilot hole (agujero guía)
A
iii
Fig. 13
A - Pilot screws (tornillos del pivote de la base)
B - Saw base (base de la sierra)
C - Hex key (llave hexagonal)
D - Narrow slot used for splinter-free cutting
(ranura angosta empleada para efectuar
cortes sin astillas)
A
BC
D
Fig. 14
A - Set scale at 0° for splinter-free cutting (ponga
la escala a 0°, para efectuar cortes sin astillas)
A
®
Fig. 15
A - Edge guide screw (tornillo de la guía para
cantos)
B - Slot (ranura)
C - Edge guide (guía para cantos)
D - Saw base (base de la sierra)
A
B
C
D
Fig. 16
A
A - Moves the laser beam laterally left to right
(sirve para mover el rayo láser de izquierda a
derecha)
B - Moves the laser beam in a rotational direction
(sirve para mover el rayo láser en una
dirección rotatoria)
B
3 – Español
REGLAS DE SEGURIDAD GENERALES
¡ADVERTENCIA! Lea todas las instrucciones.
El incumplimiento de las instrucciones señaladas
abajo puede causar descargas eléctricas, incendios
y lesiones serias. El término “herramienta eléctrica”
empleado en todos los avisos de advertencia
enumerados abajo se refiere a las herramientas
eléctricas de cordón (alámbricas) y de baterías
(inalámbricas).
GUARDE ESTAS INSTRUCCIONES
SEGURIDAD EN EL ÁREA DE TRABAJO
Mantenga limpia y bien iluminada el área de trabajo.
Un área de trabajo mal despejada o mal iluminada
propicia accidentes.
No utilice herramientas motorizadas en atmósferas
explosivas, como las existentes alrededor de líquidos,
gases y polvos inflamables. Las herramientas eléctricas
generan chispas que pueden encender el polvo y los
vapores inflamables.
Mantenga alejados a los niños y circunstantes al
maniobrar una herramienta eléctrica. Toda distracción
puede causar la pérdida del control de la herramienta.
SEGURIDAD ELÉCTRICA
Las clavijas de las herramientas eléctricas deben
corresponder a las tomas de corriente donde se
conectan. Nunca modifique la clavija de ninguna
forma. No utilice ninguna clavija adaptadora con
herramientas eléctricas dotadas de contacto a tierra.
Conectando las clavijas originales en las tomas de
corriente donde corresponden se disminuye el riesgo de
una descarga eléctrica.
Evite el contacto del cuerpo con las superficies de
objetos que estén haciendo tierra o estén conectados
a ésta, como las tuberías, radiadores, estufas y
refrigeradores. Existe un mayor riesgo de descargas
eléctricas si el cuerpo está haciendo tierra.
No exponga las herramientas eléctricas a la lluvia ni a
condiciones de humedad. La introducción de agua en
una herramienta eléctrica aumenta el riesgo de descargas
eléctricas.
No maltrate el cordón eléctrico. Nunca utilice el
cordón para trasladar, desconectar o tirar de la
herramienta eléctrica. Mantenga el cordón alejado
del calor, del aceite, de bordes afilados y de piezas
móviles. Los cordones eléctricos dañados o enredados
aumentan el riesgo de descargas eléctricas.
Al utilizar una herramienta eléctrica a la intemperie,
use un cordón de extensión apropiado para el
exterior. Usando un cordón adecuado para el exterior se
disminuye el riesgo de descargas eléctricas.
Cargue las baterías solamente con el cargador
indicado. Para utilizar con paquetes de baterías de
níquel-cadmio de 19,2 V o de iones de litio de 19,2 V,
consulte el folleto de la herramienta/aparato/paquete de
baterías/cargador complementario 988000-272.
SEGURIDAD PERSONAL
Permanezca alerta, preste atención a lo que esté
haciendo y aplique el sentido común al utilizar
herramientas eléctricas. No utilice la herramienta
eléctrica si está cansado o se encuentra bajo los
efectos de alguna droga, alcohol o medicamento.
Un momento de inatención al utilizar una herramienta
eléctrica puede causar lesiones corporales serias.
Use equipo de seguridad. Siempre póngase
protección ocular. El uso de equipo de seguridad como
mascarilla para el polvo, calzado de seguridad, casco y
protección para los oídos en las circunstancias donde
corresponda disminuye el riesgo de lesiones.
Evite un arranque accidental de la unidad. Asegúrese
de que el interruptor esté en la posición de apagado
antes de conectar la herramienta. Portar las
herramientas eléctricas con el dedo en el interruptor, o
conectarlas con el interruptor puesto, propicia accidentes.
Retire toda llave o herramienta de ajuste antes
de encender la herramienta eléctrica. Toda llave o
herramienta de ajuste dejada en una pieza giratoria de la
herramienta eléctrica puede causar lesiones.
No estire el cuerpo para alcanzar mayor distancia.
Mantenga una postura firme y buen equilibrio en todo
momento. De esta manera se logra un mejor control de la
herramienta eléctrica en situaciones inesperadas.
Vístase adecuadamente. No vista ropas holgadas
ni joyas. Mantenga el cabello, la ropa y los guantes
alejados de las piezas móviles. Las ropas holgadas, las
joyas y el cabello largo pueden engancharse en las piezas
móviles.
Si se suministran dispositivos para conectar
mangueras de extracción y captación de polvo,
asegúrese de que éstas estén bien conectadas y se
usen correctamente. La utilización de estos dispositivos
puede disminuir los peligros relacionados con el polvo.
No vista ropas holgadas ni joyas. Recójase el cabello
si está largo. Las ropas holgadas y las joyas, así como el
cabello largo, pueden resultar atraídas hacia el interior de
las aberturas de ventilación.
No utilice la unidad al estar en una escalera o en
un soporte inestable. Una postura estable sobre
una superficie sólida permite un mejor control de la
herramienta eléctrica en situaciones inesperadas.
EMPLEO Y CUIDADO DE LA HERRAMIENTA
ELÉCTRICA
No fuerce la herramienta eléctrica. Utilice la
herramienta eléctrica adecuada para cada trabajo.
La
herramienta eléctrica adecuada efectúa mejor y de manera
más segura el trabajo, si además se maneja a la velocidad
para la que está diseñada.
No use la herramienta eléctrica si el interruptor no
enciende o no apaga. Cualquier herramienta eléctrica que
no pueda controlarse con el interruptor es peligrosa y debe
repararse.
4 – Español
REGLAS DE SEGURIDAD GENERALES
Desconecte la clavija del suministro de corriente
o retire el paquete de baterías de la herramienta
eléctrica, según sea el caso, antes de efectuarle
cualquier ajuste, cambiarle accesorios o guardarla.
Tales medidas preventivas de seguridad reducen
el riesgo de poner en marcha accidentalmente la
herramienta.
Guarde las herramientas eléctricas desocupadas
fuera del alcance de los niños y no permita que
las utilicen personas no familiarizadas con las
mismas o con estas instrucciones. Las herramientas
eléctricas son peligrosas en manos de personas no
capacitadas en el uso de las mismas.
Preste servicio a las herramientas eléctricas.
Revise para ver si hay desalineación o atoramiento
de piezas móviles, ruptura de piezas o toda otra
condición que pueda afectar el funcionamiento
de la herramienta. Si está dañada la herramienta
eléctrica, llévela a reparar antes de usarla.
Numerosos accidentes son causados por herramientas
eléctricas mal cuidadas.
Mantenga las herramientas de corte afiladas y
limpias. Las herramientas de corte bien cuidadas y
con bordes bien afilados, tienen menos probabilidad
de atascarse en la pieza de trabajo y son más fáciles
de controlar.
Utilice la herramienta eléctrica, los accesorios y
brocas, hojas de corte, ruedas de esmeril, etc. de
conformidad con estas instrucciones, y de la forma
apropiada para cada una de dichas herramientas,
tomando en cuenta las condiciones de trabajo y la
tarea por realizar. Si se utiliza la herramienta eléctrica
para operaciones diferentes de las indicadas podría
originar una situación peligrosa.
EMPLEO Y CUIDADO DE LA HERRAMIENTA DE
BATERÍAS
Asegúrese de que el interruptor esté en la posición
de apagado antes de introducir el paquete de
baterías. Introducir el paquete de baterías en una
herramienta eléctrica que tenga el interruptor en
encendido propicia accidentes.
Sólo cargue el paquete de baterías con el cargador
especificado por el fabricante. Un cargador
adecuado para un tipo paquete de baterías puede
significar un riesgo de incendio si se emplea con un
paquete de baterías diferente.
Utilice las herramientas eléctricas sólo con los
paquetes de baterías específicamente indicados.
El empleo de paquetes de baterías diferentes puede
presentar un riesgo de incendio.
Cuando no esté utilizándose el paquete de baterías,
manténgalo lejos de otros objetos metálicos como
clips, monedas, llaves, clavos, tornillos y otros
objetos metálicos pequeños que puedan establecer
conexión entre ambas terminales. Establecer una
conexión directa entre las dos terminales de las
baterías puede causar quemaduras o incendios.
Si se maltratan las baterías, puede derramarse
líquido de las mismas; evite todo contacto con éste.
En caso de contacto, lávese con agua. Si el líquido
llega a tocar los ojos, además busque atención
médica. El líquido de las baterías puede causar
irritación y quemaduras.
SERVICIO
Permita que un técnico de reparación calificado
preste servicio a la herramienta eléctrica, y sólo
con piezas de repuesto idénticas. De esta manera se
mantiene la seguridad de la herramienta eléctrica.
¡ADVERTENCIA! Para reducir el riesgo de
lesiones, el usuario debe leer el manual de
instrucciones.
Al dar servicio a una herramienta eléctrica,
sólo utilice piezas de repuesto idénticas. Siga
las instrucciones señaladas en la sección
Mantenimiento de este manual. El empleo de piezas
no autorizadas o el incumplimiento de las instrucciones
de mantenimiento puede significar un riesgo de
descarga eléctrica o de lesiones.
REGLAS DE SEGURIDAD ESPECÍFICAS
Sujete las herramientas eléctricas por las
superficies aisladas de sujeción al efectuar una
operación en la cual la herramienta de corte pueda
entrar en contacto con cables ocultos o con su
propio cordón eléctrico. Todo contacto de una
herramienta con un cable cargado carga las piezas
metálicas expuestas de la herramienta y da una
descarga eléctrica al operador.

Familiarícese con su herramienta eléctrica. Lea
cuidadosamente el manual del operador. Aprenda
sus usos y limitaciones, así como los posibles
peligros específicos de esta herramienta. Al cumplir
esta regla se reduce el riesgo de descargas eléctricas,
incendios o lesiones graves.
5 – Español
Siempre use gafas de seguridad con guardas
laterales. Los cristales de los anteojos comunes
resisten sólo impactos menores. NO son anteojos de
seguridad. Al cumplir esta regla se reduce el riesgo de
posibles lesiones oculares.

Protéjase los pulmones. Use una careta o mascarilla
contra el polvo si la operación lo genera en gran
cantidad. Al cumplir esta regla se reduce el riesgo de
lesiones graves.

Protéjase los oídos. Durante períodos prolongados
de uso del producto, póngase protección para los
oídos. Al cumplir esta regla se reduce el riesgo de
lesiones corporales graves.
Las herramientas de baterías no requieren
conectarse a una toma de corriente; por tanto,
siempre están en condiciones de funcionamiento.
Tenga presentes los posibles peligros cuando no
esté usando la herramienta de baterías o cuando
esté cambiando sus accesorios. Al cumplir esta regla
se reduce el riesgo de descargas eléctricas, incendios
o lesiones graves.
No coloque herramientas de baterías ni las baterías
mismas cerca del fuego o del calor. De esta manera
se reduce el riesgo de explosiones y lesiones.
Nunca vuelva a utilizar una batería que haya sufrido una
caída o un golpe sólido. Las baterías dañadas pueden
explotar. Deseche de inmediato toda batería que haya
sufrido una caída o cualquier daño.
No aplaste, deje caer o dañe la batería. Nunca
utilice una batería o cargador que se ha caído,
aplastado, recibido un golpe contundente o ha sido
dañado(a) de alguna manera. Las baterías dañadas
pueden sufrir explosiones. Deseche de inmediato toda
batería que haya sufrido una caída o cualquier daño.
Las baterías pueden explotar en presencia de una
fuente de inflamación, como una luz indicadora
(piloto). Para reducir el riesgo de lesiones graves,
nunca use un producto inalámbrico en presencia de
llamas expuestas. La explosión de una batería puede
lanzar fragmentos y compuestos químicos. Si llegara a
tener este accidente, lávese con agua de inmediato.
No cargue la herramienta de baterías en un lugar
mojado o húmedo. Al cumplir esta regla se reduce el
riesgo de una descarga eléctrica.
Para obtener resultados óptimos, debe cargar
la herramienta de baterías en un lugar donde la
temperatura esté entre 10 y 38°C (entre 50 y 100°F).
No guarde la herramienta a la intemperie ni en el
interior de vehículos.
En condiciones extremas de uso o de temperatura,
las baterías pueden emanar líquido. Si el líquido
llega a tocarle la piel, lávese de inmediato con agua
y jabón. Si le entra líquido en los ojos, láveselos con
agua limpia por lo menos 10 minutos, y después
busque de inmediato atención médica. Al cumplir
esta regla se reduce el riesgo de lesiones graves.
ADVERTENCIAS SOBRE LA GUÍA DE LÁSER:
La radiación de la guía de láser de esta herramienta es
de Clase IIIa, con potencia máxima <5 mW y longitud
de onda de 650 nm. En el uso normal este tipo de láser
no afecta la vista, pero si ésta se mantiene fija en el haz
puede producirse ceguera por encandilamiento.
Evite la exposición directa de los ojos al emplear la guía
de láser.
El uso y el mantenimiento del láser deben hacerse
conforme a las instrucciones del fabricante.
Nunca apunte el haz hacia una persona u objeto que
no sea la pieza de trabajo.
Verifique siempre que el objeto al que dirigirá el haz del
láser sea resistente y no tenga superficies reflejantes.
Las láminas metálicas o materiales lustrosos
semejantes no se prestan al uso del láser.
Toda reparación deberá ser realizada por un
representante técnico autorizado o por el fabricante
del láser.
Guarde estas instrucciones. Consúltelas con
frecuencia y empléelas para instruir a otras personas
que puedan utilizar esta herramienta. Si presta
a alguien esta herramienta, facilítele también las
instrucciones.
REGLAS DE SEGURIDAD ESPECÍFICAS
ADVERTENCIA: Algunos polvos generados al efectuarse operaciones de lijado, aserrado, esmerilado, taladrado
y de otros tipos en la construcción, contienen sustancias químicas sabidas causantes de cáncer, defectos
congénitos y otras afecciones del aparato reproductor. Algunos ejemplos de estas sustancias químicas son:
• plomodelaspinturasabasedeplomo,
• siliciocristalinodelosladrillos,delcementoydeotrosproductosdealbañilería,y
• arsénicoycromodelamaderaquímicamentetratada.
El riesgo de la exposición a estos compuestos varía, según la frecuencia con que se realice este tipo de trabajo.
Para reducir la exposición personal a este tipo de compuestos: trabaje en áreas bien ventiladas, y con equipo
de seguridad aprobado, tal como las caretas para el polvo especialmente diseñadas para filtrar partículas
microscópicas.
6 – Español
SÍMBOLOS
Es posible que se empleen en este producto algunos de los siguientes símbolos. Le suplicamos estudiarlos y
aprender su significado. Una correcta interpretación de estos símbolos le permitirá utilizar mejor y de manera más
segura el producto.
SÍMBOLO NOMBRE DENOMINACIÓN/EXPLICACIÓN
Alerta de seguridad Indica un peligro posible de lesiones personales.
Lea el manual del operador Para reducir el riesgo de lesiones, el usuario debe leer y
comprender el manual del operador antes de usar este producto.
Protección ocular Siempre póngase protección ocular con la marca de
cumplimiento de la norma ANSI Z87.1.
Símbolo de no acercar las manos Si no mantiene las manos alejadas de la hoja de corte, se
causará serias lesiones corporales.
Alerta de condiciones húmedas No exponga la unidad a la lluvia ni la use en lugares húmedos.
Li - Ion
Símbolos de reciclado
Este producto contiene baterías de níquel-cadmio (Ni-
Cd) o iones de litio (Li-ion). Es posible que algunas leyes
municipales, estatales o federales prohíban desechar las
baterías en la basura normal. Consulte a las autoridades
reguladoras de desechos para obtener información en
relación con las alternativas de reciclado y desecho
disponibles.
V Volts Voltaje
min Minutos Tiempo
Corriente continua Tipo o característica de corriente
n
o
Velocidad en vacío Velocidad de rotación, en vacío
.../min Por minuto Revoluciones, carreras, velocidad superficial, órbitas, etc.,
por minuto
Las siguientes palabras de señalización y sus significados tienen el objeto de explicar los niveles de riesgo
relacionados con este producto.
SÍMBOLO SEÑAL SIGNIFICADO
PELIGRO: Indica una situación peligrosa inminente, la cual, si no se evita, causará
la muerte o lesiones serias.
ADVERTENCIA: Indica una situación peligrosa posible, la cual, si no se evita, podría causar
la muerte o lesiones serias.
PRECAUCIÓN: Indica una situación peligrosa posible, la cual, si no se evita, podría causar
lesiones menores o leves.
PRECAUCIÓN: (Sin el símbolo de alerta de seguridad) Indica una situación que puede
producir daños materiales.
7 – Español
CARACTERÍSTICAS
ESPECIFICACIONES DEL PRODUCTO
Longitud de la carrera .............................1 pulg. (25,4 mm)
Carreras por minuto ....................................... 0-2100 /min.
Interruptor .............................................. Velocidad variable
Mordaza de la cuchilla ............. De apriete sin herramienta
Ángulodecorte ...De 0º a 45º, a la izquierda y a la derecha
Movimiento orbital .......................................... 4 posiciones
Guía láser .......................... Clase IIIa, <5mW máx, 650 nm
FAMILIARÍCESE CON LA SIERRA DE VAIVÉN
ORBITAL
Vea la figura 1, página i.
Para usar este producto con la debida seguridad se debe
comprender la información indicada en la herramienta
misma y en este manual, y se debe comprender también
el trabajo que intenta realizar. Antes de usar este
producto, familiarícese con todas las características de
funcionamiento y normas de seguridad del mismo.
COMPARTIMIENTO DE LAS HOJAS
Cuando no esté utilizando la unidad, puede guardar las
hojas suministradas con la sierra de vaivén orbital en el
compartimiento situado en la parte posterior de la misma.
DISEÑO ERGONÓMICO
El diseño de la sierra de vaivén orbital permite un fácil
manejo de la misma. El diseño brinda una sujeción
cómoda y fácil para el trabajo en diferentes posiciones y
ángulos.
GUÍAS LÁSER
La guía láser generan un rayo láser de color rojo en la
superficie de trabajo delante de la sierra cuando la misma
está encendida.
BOTÓN DEL SEGURO DE APAGADO
La sierra está dotada de un botón de seguro de apagado,
el cual reduce la posibilidad de un arranque accidental.
PERILLA DE AJUSTE DE ÓRBITA
Cuatro posiciones de movimiento orbital, de corte fino a
agresivo.
MORDAZA DE LA CUCHILLA DE APRIETE SIN
HERRAMIENTA
La mordaza de la hoja de la sierra no requiere ninguna
herramienta (llave de la hoja) al instalarse o desmontarse
la hoja.
VELOCIDAD VARIABLE
Esta herramienta dispone de un interruptor de velocidad
variable, el cual produce mayor velocidad cuanto mayor
presión se aplica en el gatillo.
8 – Español
ARMADO
DESEMPAQUETADO
Embarcamos este producto completamente armado.
Extraiga cuidadosamente de la caja la herramienta
y los accesorios. Asegúrese de que estén presentes
todos los artículos enumerados en la lista de
empaquetado.
ADVERTENCIA: No use este producto si no está
totalmente ensamblado o si alguna pieza falta o está
dañada. Si utiliza un producto que no se encuentra
ensamblado de forma correcta y completa, puede
sufrir lesiones graves.
Inspeccione cuidadosamente la herramienta para
asegurarse de que no haya sufrido ninguna rotura o
daño durante el transporte.
No deseche el material de empaquetado hasta que
haya inspeccionado cuidadosamente la herramienta y
la haya utilizado satisfactoriamente.
Si hay piezas dañadas o faltantes, le suplicamos llamar
al 1-800-932-3188, donde le brindaremos asistencia.
LISTA DE EMPAQUETADO
Sierra de vaivén orbital
Hoja
Llave hexagonal
Manual del operador
ADVERTENCIA: Si falta o está dañada
alguna pieza, no utilice este producto sin haber
reemplazado la pieza. Usar este producto con partes
dañadas o faltantes puede causar lesiones serias al
operador.
ADVERTENCIA: No intente modificar esta
herramienta ni hacer accesorios no recomendados
para la misma. Cualquier alteración o modificación
constituye maltrato el cual puede causar una
condición peligrosa, y como consecuencia posibles
lesiones corporales serias.
ADVERTENCIA: Para evitar un arranque accidental
que podría causar lesiones corporales serias,
siempre desmonte de la herramienta el paquete de
baterías al montarle piezas a aquélla.
9 – Español
ADVERTENCIA: No permita que su familarización
con las herramientas lo vuelva descuidado.
Recuerde que un descuido de un instante es
suficiente para causar una lesión grave.
ADVERTENCIA: Siempre póngase protección
ocular con protección lateral con la marca
de cumplimiento de la norma ANSI Z87.1. La
inobservancia de esta advertencia puede permitir
que los objetos lanzados hacia los ojos puedan
provocarle lesiones graves.
ADVERTENCIA: No utilice ningún aditamento o
accesorio no recomendado por el fabricante de esta
producto. El empleo de aditamentos o accesorios no
recomendandos podría causar lesiones serias.
APLICACIONES
Esta herramienta puede emplearse para los fines
siguientes:
Corte de metales no ferrosos, lámina de acero,
madera, plástico y materiales similares
Corte de superficies de madera
Corte de chapa metálica delgada
Corte de plásticos y laminados
Este producto acepta los paquetes de baterías Craftsman
de iones de litio de 19,2 V y los paquetes de baterías
Craftsman de níquel-cadmio de 19,2 V.
Para ver las instrucciones de carga completas, consulte
los manuales del operador del paquete de baterías y los
modelos de cargador.
CARACTERÍSTICAS DE PROTECCIÓN DE LAS
BATERÍAS
Las baterías de iones de litio Craftsman de 19,2 V están
diseñadas con características que protegen las celdas de
iones de litio y maximizan la duración de las baterías.
Si la herramienta se detiene durante el uso, suelte el
gatillo para reiniciarla y reanude el funcionamiento. Si aun
así no funciona, se debe recargar la batería.
PARA INSTALAR EL PAQUETE DE BATERÍAS
Vea la figura 2, página i.
Asegure el interruptor de gatillo; para ello, coloque el
selector de dirección de rotación en la posición central.
Coloque el paquete de baterías en la herramienta.
Asegúrese de que los pestillos situados en ambos
lados del paquete de baterías entren completamente
en su lugar con un chasquido y de que el paquete
quede bien asegurado en la herramienta antes de
empezar a utilizar ésta.
FUNCIONAMIENTO
PRECAUCIÓN: Al colocar el paquete de baterías
en la herramienta, asegúrese de que la costilla del
paquete quede alineada con la ranura del interior
de la herramienta y de que los pestillos entren
completamente en su lugar con un chasquido. Si
no se monta debidamente el paquete de baterías
pueden dañarse los componentes internos.
ADVERTENCIA: Retire siempre el paquete de
baterías de la herramienta antes de instalar las
piezas, realizar ajustes. limpiarla o cuando no la
utilice. Retirar el paquete de baterías evitará que
la unidad se accione accidentalmente y provoque
lesiones graves.
DESMONTAJE DEL PAQUETE DE BATERÍAS
Vea la figura 2, página i.
Asegure el interruptor de gatillo; para ello, coloque el
selector de dirección de rotación en la posición central.
Oprima los pestillos laterales del paquete de baterías.
Retire de la herramienta el paquete de baterías.
ADVERTENCIA: Para evitar un arranque accidental
que podría causar lesiones corporales serias,
siempre desmonte de la herramienta el paquete de
baterías al montarle piezas a aquélla.
PARA INSTALAR LAS HOJAS
Vea la figura 3, página i.
Retire el paquete de baterías.
Levante la palanca de aseguramiento y afloje de la
mordaza, en la parte frontal de la sierra.
Inserte la hoja entre la mordaza y la barra de la sierra
tan lejos como sea posible.
Afloje y luego asegure la palanca de la mordaza de la hoja.
Vuelva a colocar el paquete de baterías.
SELECCIÓN DE LA HOJA
Para lograr un desempeño óptimo de la sierra, es
importante escoger una hoja específicamente para el uso
deseado y el material en particular por cortar. Haciéndolo
así logra un corte más limpio y rápido, así como una vida
de servicio más prolongada de la hoja de corte. Hay hojas
de repuesto para esta sierra en la tienda Sears de su
preferencia. Se recomienda utilizar hojas con fuste en “T”.
Si no hay ninguna hoja con fuste en “T”, puede utilizarse
una de alta calidad con fuste en “U”.
COMPARTIMIENTO DE LAS HOJAS
Vea la figura 4, página i.
Una útil característica de la sierra es el compartimiento
para las hojas de corte. El compartimiento de hojas está
en la parte posterior de la sierra. Es útil para guardar hojas
extra y la regular cuando no está usándose.
10 – Español
FUNCIONAMIENTO
Para abrir: Empuje la puerta hacia abajo con el pulgar u
otro dedo. Coloque las hojas en el compartimiento de las
mismas.
Para cerrar: Empuje la puerta hacia abajo con el pulgar u
otro dedo.
LUGAR DE GUARDAR LA LLAVE HEXAGONAL
Vea la figura 5, página ii.
La llave hexagonal se asegura en la base de la sierra,
detrás de la orejeta recubierta de goma. Empújela para
introducirla en su lugar.
Asegúrese de que esté asegurada la llave hexagonal
antes de efectuar cualquier operación de aserrado.
Para retirar la llave hexagonal, tire de la misma.
GUÍA LÁSER
Vea la figura 6, página ii.
Oprima el interruptor de la guía láser para generar un rayo láser
rojo en la superficie de trabajo al frente de la sierra. Utilice el
láser para guiar la sierra a lo largo de la línea de corte.
BOTÓN DEL SEGURO DE APAGADO
Vea la figura 7, página ii.
El botón del seguro de apagado se encuentra en el mango,
arriba del gatillo del interruptor. Debe oprimir el botón del
seguro de apagado con el fin de poder tirar del gatillo del
interruptor. El seguro se autoengancha cada vez que se
suelta el gatillo.
NOTA: El botón del seguro de apagado puede oprimirse
desde el lado izquierdo o el derecho.
GATILLO DEL INTERRUPTOR
Vea la figura 7, página ii.
Para encender la sierra, oprima y no suelte el botón del
seguro de apagado y luego oprima del gatillo del interruptor.
Para apagarlo, suelte el gatillo del interruptor.
CORTES GENERALES
Vea la figura 7, página ii.
Deje descansar la parte frontal de la base de la sierra en
la pieza de trabajo y alinee el borde de corte de la hoja
con la línea de dicha pieza.
Encienda la sierra y desplácela hacia adelante por la
superficie de la pieza de trabajo.
Aplique presión hacia abajo para mantener estable la
sierra, y hacia adelante aplique sólo la presión suficiente
para mantener la sierra cortando.
No fuerce la sierra. Si se fuerza la sierra puede recalentarse
el motor y puede romperse la hoja de corte. Debe
descargarse toda hoja rota. Retire de la mordaza la parte
restante de la hoja e instale una hoja nueva.
ADVERTENCIA: Una presión lateral excesiva puede
producir la ruptura de la hoja o daños en la pieza de
trabajo.
MOVIMIENTO ORBITAL
Vea la figura 7, página ii.
La hoja de la sierra corta con un movimiento orbital. Esta
característica es ajustable y proporciona un corte más rápido
y eficiente. La hoja corta la pieza de trabajo en la carrera
ascendente pero no roza la pieza durante la carrera descen-
dente. Los ajustes más elevados deben utilizarse cuando se
desea cortar rápido material suave. Los ajustes más bajos
deben utilizarse para cortar materiales de mayor resistencia.
CORTES RECTOS
Vea la figura 7, página ii.
Pueden realizarse cortes rectos fijando con prensas de mano
una tabla recta o regla en la pieza de trabajo y guiando el
borde de la sierra contra la misma. Efectúe el corte en una
dirección solamente. No corte hasta medio camino, para
luego completar el corte a partir del extremo opuesto.
CORTES CONTORNEADOS
Vea la figura 8, página ii.
Pueden efectuarse cortes contorneados con la sierra de
vaivén; para ello, guíe la dirección del corte aplicando
presión lateral en el mango.
CORTES EN ÁNGULO (CORTES A BISEL)
Vea las figuras 9 y 10, página ii.
El ángulo del corte a bisel puede ajustarse de 0° a 45°, a la
derecha o a la izquierda. Puede cortarse en ángulos de 0° a
45°, los cuales están marcados en la escala en incrementos
de 15°, tanto en el lado izquierdo como en el derecho de
la base. Hay muescas en la parte posterior de la base, las
cuales sirven de topes en cada uno de los incrementos
de 15° mencionados arriba. Cuando se requieren cortes
precisos, se recomienda utilizar un transportador de ángulos.
Retire el paquete de baterías.
Con la llave hexagonal de 1/8 pulg. suministrada afloje los
tornillos del pivote de la base hasta que pueda desmontar
ésta.
Deslice hacia adelante la base hasta que los tornillos del
pivote de la misma puedan moverse libremente en las
ranuras.
Alinee la marca de la base correspondiente al ángulo
deseado con el borde del alojamiento del motor.
Una vez alcanzado el ángulo deseado, retroceda la base
hasta alinear la orejeta del alojamiento del motor con la
muesca correspondiente, en la parte posterior de la base.
NOTA: Al preparar la unidad con un transportador de
ángulos con el fin de efectuar cortes precisos, o para
ángulos diferentes de los prefijados a incrementos de 15°,
no se usan las muescas de tope de la parte poserior de la
base.
Apriete firmemente los tornillos del pivote de la base.
Vuelva a colocar la llave hexagonal en el compartimiento.
Vuelva a colocar el paquete de baterías.
NOTA: Al efectuarse cortes a bisel, contorneados, de
penetración y en metal, debe utilizarse la ranura ancha de la
base.
11 – Español
FUNCIONAMIENTO
CORTES DE PENETRACIÓN
Vea las figuras 11 y 12, página ii.
ADVERTENCIA: Para evitar perder el control,
romper hojas o dañar la pieza de trabajo, siempre tenga
extrema precaución al efectuar cortes de penetración.
No recomendamos efectuar cortes de penetración en
ningún material que no sea madera.
PARA EFECTUAR UN CORTE DE PENETRACIÓN
Marque claramente la línea de corte en la pieza de
trabajo.
Fije el ángulo de corte a 0° y ajuste la órbita a “0”.
Perfore un agujero guía a través de cualquier punto en la
línea de corte
Encienda la sierra a alta velocidad y lentamente baje la
hoja a través del agujero guía para introducirla en la pieza
de trabajo hasta que empiece a cortar a través de la
madera.
No mueva hacia adelante la base hasta que la hoja no
corte totalmente a través de la pieza de trabajo y la base
toque completamente dicha pieza.
Mueva hacia adelante la sierra para terminar la abertura.
Para este tipo de corte sólo utilice hoja de siete dientes
por pulgada.
CORTES SIN ASTILLAS
Vea las figuras 13 y 14, páginas ii y iii.
La base de la sierra de vaivén dispone de una ranura angosta
que permite efectuar cortes sin astillas. Es útil especialmente
al cortar madera contrachapada. Esta característica debe
utilizarse solamente al efectuar cortes rectos o circulares. No
es para cortes en bisel ni en introducción vertical.
NOTA: El ajuste sin nada de órbita también ayuda a reducir
el astillamiento al cortar madera contrachapada.
FORMA DE COLOCAR LA BASE EN LA POSICIÓN
DE CORTE SIN ASTILLAS
Retire el paquete de baterías.
Con la llave hexagonal de 1/8 pulg. suministrada afloje
los tornillos del pivote de la base y deslice ésta hacia
adelante.
Para lograr cortes sin astillas siempre fije el ángulo de
corte a 0°. Para fijar el ángulo de corte a 0°, alinee la
marca de 0° de la escala con el borde del alojamiento del
motor.
NOTA: Al fijar el ángulo de corte a 0° para efectuar cortes
sin astillas, no se utilizan las muescas de tope de la parte
posterior de la base.
Apriete firmemente los tornillos del pivote de la base.
Retire la llave hexagonal y vuelva a colocarla en el
compartimiento.
Vuelva a colocar el paquete de baterías.
GUÍA PARA CANTOS OPTATIVA
Vea la figura 15, página iii.
Hay a la disponibilidad una guía optativa para cantos para
usarse con la sierra. Puede utilizarse tanto para cortes
transversales como para cortes al hilo.
Retire el paquete de baterías.
Afloje el tornillo de la guía para cantos.
Introduzca el brazo a través de las dos ranuras de la base
de la sierra, como se muestra.
Ajuste la guía para cantos al ancho deseado y asegúrela
en su lugar con el tornillo de la misma.
Vuelva a colocar el paquete de baterías.
AJUSTES
PRECAUCIÓN: Todo control, ajuste o procedimiento
diferente de los especificados aquí, puede causar una
exposición peligrosa a la radiación.
AJUSTE EL LÁSER
See Figure 16, página iii.
El láser puede realinearse ajustando los dos tornillos
ubicados en la parte delantera de la sierra. El tornillo superior
sirve para mover el rayo láser de izquierda a derecha. El
tornillo inferior sirve para mover el rayo láser en una dirección
rotatoria.
NOTA: trace con un lápiz una línea recta en una pieza de
trabajo desechable paralela al borde largo de la base como
guía para el proceso de ajuste.
Encienda el láser.
Deje descansar la base de la sierra en una pieza de
trabajo desechable.
Ajuste los tornillos según sea necesario.
Puesto que el espesor de las hojas varía, siempre realice
un corte de prueba en una pieza de trabajo desechable
para asegurar la precisión del corte.
Verifique la alineación.
Repita el procedimiento según sea necesario hasta dejar
alineado el láser.
12 – Español
MANTENIMIENTO
ADVERTENCIA: Al dar servicio a la herramienta,
sólo utilice piezas de repuesto Craftsman idénticas.
El empleo de piezas diferentes puede presentar un
peligro o causar daños al producto.
ADVERTENCIA: Cuando utilice aire comprimido
para limpiar herramientas, póngase siempre gafas
protectoras o anteojos de seguridad con protección
lateral. Si la operación genera mucho polvo, también
póngase una mascarilla contra el polvo.
ADVERTENCIA: Para evitar lesiones corporales
serias, siempre retire el paquete de baterías de la
herramienta al limpiarla o darle mantenimiento.
MANTENIMIENTO GENERAL
Evite el empleo de solventes al limpiar piezas de plástico.
La mayoría de los plásticos son susceptibles a diferentes
tipos de solventes comerciales y pueden resultar
dañados. Utilice paños limpios para eliminar la suciedad,
el polvo, el aceite, la grasa, etc.
ADVERTENCIA: No permita en ningún momento
que fluidos para frenos, gasolina, productos a base
de petróleo, aceites penetrantes, etc., lleguen a
tocar las piezas de plástico. Las sustancias químicas
pueden dañar, debilitar o destruir el plástico, lo cual
a su vez puede producir lesiones corporales serias.
Solamente las piezas mostradas en la lista de piezas
pueden ser reparadas o cambiadas por el consumidor.
Todas piezas restantes deben ser reemplazadas en un
centro de servicio Sears.
REMOCIÓN Y PREPARACIÓN DEL PAQUETE DE
BATERÍAS PARA EL RECICLADO
ADVERTENCIA: Al retirar el paquete de baterías,
cubra las terminales del mismo con cinta adhesiva
reforzada. No intente destruir o desarmar el
paquete de baterías, ni de desmontar ninguno de
sus componentes. Las baterías deben reciclarse o
desecharse debidamente. Asimismo, nunca toque
ambas terminales con objetos metálicos y partes del
cuerpo, ya que puede producirse un corto circuito.
Manténgase fuera del alcance de los niños. La
inobservancia de estas advertencias puede causar
incendios y lesiones corporales serias.
Los siguientes accesorios recomendados se encuentran en las tiendas Sears:
Guía para cantos ....................................................................................................................................Art. Núm. 926320
ADVERTENCIA: Arriba se señalan los aditamentos y accesorios disponibles para usarse con esta herramienta.
No utilice ningún aditamento o accesorio no recomendado por el fabricante de esta herramienta. El empleo de
aditamentos o accesorios no recomendandos puede causar lesiones serias.
ACCESORIOS
13
NOTAS
14
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME®(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR®
(1-888-784-6427)
Au Canada pour service en français:
1-800-LE-FOYERMC
(1-800-533-6937)
www.sears.ca

Navigation menu