Craftsman Diehard Automatic Battery Charger 10 2 50 Amp Owners Manual

12V Battery Charger & Engine Starter 2871222 spin_prod_751317212

DIEHARD 200.7122 spin_prod_751317212

2015-03-28

: Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-660983 craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual-660983 craftsman pdf

Open the PDF directly: View PDF PDF.
Page Count: 12

0099001078-03
12V Battery Charger & Engine Starter
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
OPERATOR’S MANUAL
Model No.
2871222
Read and follow all Safety
Rules and Operating Instructions
before Every Use of this Product.
SAVE THESE INSTRUCTIONS.
2
DIEHARD THREE-YEAR FULL WARRANTY
When operated and maintained according to all supplied instructions, if this DieHard
product fails due to a defect in material or workmanship within 3 years from the date
of purchase, return it to any DieHard outlet in the United States for free replacement.
This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
FOR CUSTOMER ASSISTANCE OR REPLACEMENT PARTS,
CALL TOLL-FREE FROM 7 AM TO 5 PM CT
MONDAY THROUGH FRIDAY: 1-800-732-7764
3
IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.
SAVE THESE INSTRUCTIONS – This manual will show you how to use your charger
safely and effectively. Please read, understand and follow these instructions and
precautions carefully, as this manual contains important safety and operating instructions.
The safety messages used throughout this manual contain a signal word.
The signal word indicates the level of the hazard in a situation.
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result in
moderate or minor injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result in
damage to the equipment or vehicle or property damage.
Pursuant to California Proposition 65, this product contains chemicals known to
the State of California to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
1. IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS.
This manual contains important safety and operating instructions.
RISK OF ELECTRIC SHOCK OR FIRE.
1.1 Keep out of reach of children.
1.2 Do not expose the charger to rain or snow.
1.3 Use only recommended attachments. Use of an attachment
not recommended or sold by the battery charger manufacturer
may result in a risk of re, electric shock or injury to persons or damage to property.
1.4 To reduce the risk of damage to the electric plug or cord, pull by the plug rather than the
cord when disconnecting the charger.
1.5 An extension cord should not be used unless absolutely necessary. Use of an improper
extension cord could result in a risk of re and electric shock. If an extension cord must be
used, make sure:
That the pins on the plug of the extension cord are the same number, size and shape
as those of the plug on the charger.
That the extension cord is properly wired and in good electrical condition.
That the wire size is large enough for the AC ampere rating of the charger as
specied in section 8.
1.6 To reduce the risk of electric shock, unplug the charger from the outlet before attempting
any maintenance or cleaning. Simply turning off the controls will not reduce this risk.
1.7 Do not operate the charger with a damaged cord or plug; have the cord or plug replaced
immediately by a qualied service person.
1.8 Do not operate the charger if it has received a sharp blow, been dropped or otherwise
damaged in any way; take it to a qualied service person.
1.9 Do not disassemble the charger; take it to a qualied service person when service or
repair is required. Incorrect reassembly may result in a risk of re or electric shock.
4
RISK OF EXPLOSIVE GASES.
1.10 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST
IMPORTANCE THAT YOU FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
EACH TIME YOU USE THE CHARGER.
1.11 To reduce the risk of a battery explosion, follow all instructions in this manual and those
published by the battery manufacturer and the manufacturer of any equipment you intend
to use in the vicinity of the battery. Review the cautionary markings on these products and
on the engine.
1.12 This charger employs parts, such as switches and circuit breakers, that tend to produce arcs
and sparks. If used in a garage, locate this charger 18 inches or more above oor level.
2. PERSONAL PRECAUTIONS
RISK OF EXPLOSIVE GASES.
2.1 NEVER smoke or allow a spark or ame in the vicinity of a battery or engine.
2.2 Remove personal metal items such as rings, bracelets, necklaces and watches
when working with a lead-acid battery. A lead-acid battery can produce a short-circuit
current high enough to weld a ring or the like to metal, causing a severe burn.
2.3 Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might
spark or short-circuit the battery or other electrical part that may cause an explosion.
2.4 Use this charger for charging LEAD-ACID batteries only. It is not intended to supply power
to a low voltage electrical system other than in a starter-motor application. Do not use
this battery charger for charging dry-cell batteries that are commonly used with home
appliances. These batteries may burst and cause injury to persons and damage to property.
2.5 NEVER charge a frozen battery.
2.6 Consider having someone nearby to come to your aid when you work near a lead-acid battery.
2.7 Have plenty of fresh water and soap nearby in case battery acid contacts your skin,
clothing or eyes.
2.8 Wear complete eye and body protection, including safety goggles and protective clothing.
Avoid touching your eyes while working near the battery.
2.9 If battery acid contacts your skin or clothing, immediately wash the area with soap and
water. If acid enters your eye, immediately ood the eye with cold running water for at
least 10 minutes and get medical attention right away.
2.10 If battery acid is accidentally swallowed, drink milk, the whites of eggs or water. DO NOT
induce vomiting. Seek medical attention immediately.
3. PREPARING TO CHARGE
RISK OF CONTACT WITH BATTERY ACID. BATTERY ACID IS A
HIGHLY CORROSIVE SULFURIC ACID.
3.1 If it is necessary to remove the battery from the vehicle to
charge it, always remove the grounded terminal rst. Make sure all
of the accessories in the vehicle are off, to prevent arcing.
3.2 Be sure the area around the battery is well ventilated while the battery is being charged.
3.3 Clean the battery terminals before charging the battery. During cleaning, keep airborne
corrosion from coming into contact with your eyes, nose and mouth. Use baking soda and
water to neutralize the battery acid and help eliminate airborne corrosion. Do not touch
your eyes, nose or mouth.
3.4 Add distilled water to each cell until the battery acid reaches the level specied by the
battery manufacturer. Do not overll. For a battery without removable cell caps, such
as valve regulated lead-acid batteries (VRLA), carefully follow the manufacturer’s
recharging instructions.
5
3.5 Read, understand and follow all instructions for the charger, battery, vehicle and any
equipment used near the battery and charger. Study all of the battery manufacturer’s
specic precautions while charging and recommended rates of charge.
3.6 Determine the voltage of the battery by referring to the vehicle owner’s manual and make
sure that the output voltage is correct for your battery.
3.7 Make sure that the charger cable clips make tight connections.
4. CHARGER LOCATION
RISK OF EXPLOSION AND CONTACT WITH
BATTERY ACID.
4.1 Locate the charger as far away from the
battery as the DC cables permit.
4.2 Never place the charger directly above the
battery being charged; gases from the battery will corrode and damage the charger.
4.3 Do not set the battery on top of the charger.
4.4 Never allow battery acid to drip onto the charger when reading the electrolyte specic
gravity or lling the battery.
4.5 Do not operate the charger in a closed-in area or restrict the ventilation in any way.
5. DC CONNECTION PRECAUTIONS
5.1 Connect and disconnect the DC output clips only after removing the AC plug from the
electrical outlet. Never allow the clips to touch each other.
5.2 Attach the clips to the battery and chassis, as indicated in sections 6 and 7.
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
A SPARK NEAR THE BATTERY MAY CAUSE A
BATTERY EXPLOSION. TO REDUCE THE RISK
OF A SPARK NEAR THE BATTERY:
6.1 Position the AC and DC cables to reduce the
risk of damage by the hood, door and moving or hot
engine parts. NOTE: If it is necessary to close the
hood during the charging process, ensure that the hood does not touch the metal part of
the battery clips or cut the insulation of the cables.
6.2 Stay clear of fan blades, belts, pulleys and other parts that can cause injury.
6.3 Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has
a larger diameter than the NEGATIVE (NEG, N, -) post.
6.4 Determine which post of the battery is grounded (connected) to the chassis (vehicle
frame). If the negative post is grounded to the chassis (as in most vehicles), see step 6.5.
If the positive post is grounded to the chassis, see step 6.6.
6.5 For a negative-grounded vehicle, connect the POSITIVE
(RED) clip from the battery charger to the POSITIVE
(POS, P, +) ungrounded post of the battery. Connect the
NEGATIVE (BLACK) clip to the vehicle frame or engine
block at a distance away from the battery. Do not connect
the clip to the carburetor, fuel lines or sheet-metal body
parts. Connect to a heavy gauge metal part of the vehicle
frame or engine block.
NEGATIVE GROUNDED SYSTEM
6
6.6 For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the battery
charger to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clip to the vehicle frame or engine block at a distance away from the
battery. Do not connect the clip to the carburetor, fuel lines or sheet-metal body parts.
Connect to a heavy gauge metal part of the vehicle frame or engine block.
6.7 Connect charger AC supply cord to electrical outlet.
6.8 When disconnecting the charger, disconnect the AC cord, remove the clip from the vehicle
chassis and then remove the clip from the battery terminal.
6.9 See CALCULATING CHARGE TIME for length of charge information.
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
A SPARK NEAR THE BATTERY MAY CAUSE A
BATTERY EXPLOSION. TO REDUCE THE RISK
OF A SPARK NEAR THE BATTERY:
7.1 Check the polarity of the battery posts. The
POSITIVE (POS, P, +) battery post usually has a
larger diameter than the NEGATIVE (NEG, N, -) post.
7.2 Attach at least a 24-inch (61 cm) long 6-gauge (AWG) insulated battery cable to the
NEGATIVE (NEG, N, -) battery post.
7.3 Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +) post of the battery.
7.4 Position yourself and the free end of the cable you previously attached to the NEGATIVE
(NEG, N, -) battery post as far away from the battery as possible – then connect the
NEGATIVE (BLACK) charger clip to the free end of
the cable.
7.5 Do not face the battery when making the nal
connection.
7.6 Connect charger AC supply cord to electrical outlet.
7.7 When disconnecting the charger, always do so in
the reverse order of the connecting procedure and
break the rst connection while as far away from the battery as practical.
7.8 A marine (boat) battery must be removed and charged on shore. To charge it onboard
requires equipment specially designed for marine use.
8. GROUNDING AND AC POWER CORD CONNECTIONS
RISK OF ELECTRIC SHOCK OR FIRE.
8.1 This battery charger is for use on a nominal
120-volt circuit and has a grounded plug that
looks like the plug illustrated. The charger must
be grounded to reduce the risk of electric shock.
The plug must be plugged into an outlet that is
properly installed and grounded in accordance with all local codes and
ordinances. The plug pins must t the receptacle (outlet). Do not use with
an ungrounded system.
8.2 Never alter the AC cord or plug provided – if it does not t the outlet, have
a proper grounded outlet installed by a qualied electrician. An improper connection can
result in a risk of an electric shock or electrocution. NOTE: Pursuant to Canadian
Regulations, use of an adapter plug is not allowed in Canada. Use of an adapter plug in
the United States is not recommended and should not be used.
8.3 Recommended minimum AWG size for extension cord:
100 feet (30.5 meters) long or less – use a 14 gauge (2.08 mm2) extension cord.
Over 100 feet (30.5 meters) long – use a 10 gauge (5.26 mm2) extension cord.
7
9. ASSEMBLY INSTRUCTIONS
Remove all cord wraps and uncoil the cables prior to using the battery charger.
10. FEATURES /CONTROL PANEL
1. Ammeter
2. Battery Type Selector Switch
3. Charge Rate Selector Switch
4. Battery Clips
5. Full Charge LED
1
5
2
3
4
Setting the controls
All of the controls for your charger are located on the front of the charger. Read these
instructions to properly set the charger controls.
Ammeter
The Ammeter indicates the amount of current, measured in amps, that is being drawn
by the battery. As a battery takes on a charge, it draws less current from the charger.
Correspondingly, the meter will show less current being drawn by the battery. When the
current stops decreasing, the battery is charged.
The 2 amp charge rate may indicate some activity on the meter, although the meter does
not have the resolution to display this low rate. For the 2 amp charge rate, a triangle has
been provided. Its accuracy has been calibrated for use with small batteries.
Percent of Charge
The percent of charge is based on the current drawn by the battery. For this reason,
accuracy will vary with the size and battery type.
LED Indicators
On Steady – Battery is fully charged and the charger is in Maintain Mode.
Fast Blink (4x per second) – Charger is ready to crank the engine in Engine
Start Mode.
Slow Blink (1x per second) – Charger is in Engine Start Cool Down Mode.
Two Blinks (followed by pause) – Charger is in Abort Mode.
Battery Type Switch
Use this switch to set the type of battery to be charged – Standard or AGM. Both settings
are for regular and deep-cycle batteries. If you are not sure which type of battery you
have, select the AGM setting.
Charge Rate Selector Switch:
Use the Charge Rate Selector switch to select the charge rate setting you require.
8
11. OPERATING INSTRUCTIONS
This battery charger must be properly assembled in accordance with the
assembly instructions before it is used.
NOTE: The charger does not have an ON/OFF switch. The ON and OFF commands are
controlled by plugging the 71222 into a 120V AC electrical wall outlet only after the battery
connections have been made.
Charging
1. Make sure to place the charger on a dry, non-ammable surface, such as metal
or concrete.
2. Ensure that all of the charger components are in place and in good working condition,
including the plastic boots on the battery clips.
3. Connect the battery, following the precautions listed in sections 6 and 7.
4. Select the appropriate settings for your battery.
5. Connect the AC power, following the precautions listed in section 8.
6. To disconnect the charger, reverse the above procedures.
Automatic Operation
When an automatic charge is performed, the charger switches to a maintain mode
automatically after the battery is charged.
Aborted Charge
If charging cannot be completed normally, charging will abort. When charging aborts, the
charger’s output is shut off and the LED will blink (two blinks followed by a pause). All
charger function switches become non-functional. To reset after an aborted charge, unplug
the charger from the AC outlet, wait a few moments and plug it back in.
Completion of Charge
Charge completion is indicated by the LED. When lit steadily, the charger has switched to
the Maintain Mode of operation.
Maintain Mode (Float-Mode Monitoring)
When the LED is lit, the charger has started Maintain Mode. In this mode, the charger
keeps the battery fully charged by delivering a small current when necessary.
NOTE: If the charger has to provide its maximum Maintain Mode current for a continuous
12 hour period, it will go into Abort Mode (see Aborted Charge section). This is usually
caused by a drain on the battery or a bad battery. Make sure there are no loads on the
battery. If there are, remove them. If there are none, have the battery checked or replaced.
Maintaining a Battery (2 amp charge rate)
The charger maintenance setting will keep 12 volt batteries at full charge. The setting can
also be used to charge smaller batteries. However, if you use the setting to charge a large
battery, such as a marine deep-cycle battery, battery capacity may be lost. The battery
would then be unable to hold a charge and become useless. Avoid using the maintenance
setting to charge a large battery.
NOTE: The maintain mode technology utilized in DieHard chargers allows you to safely
charge and maintain a healthy battery for extended periods of time. However, problems
with the battery, electrical problems in the vehicle, improper connections or other
unanticipated conditions could cause excessive current draws. As such, occasionally
monitoring your battery and the charging process is recommended.
9
Using the 50 Amp Engine Start feature
Your battery charger can be used to jumpstart your car if the battery is low. Follow these
instructions on how to use the ENGINE START feature.
Follow all safety instructions and precautions for charging your battery.
Wear complete eye protection and clothing protection. Charge your
battery in a well-ventilated area.
Using the ENGINE START feature WITHOUT a battery installed in the
vehicle could cause damage to the vehicle’s electrical system. NOTE: If
you have charged the battery and it still will not start your car, do not use
the engine start feature, or it could damage the vehicle’s electrical system.
Do not leave the charger in Engine Start Mode for longer than 9 minutes at
a time, or you will damage the charger.
1. With the charger unplugged from the AC outlet, connect the charger to the battery
following the instructions given in section 6: FOLLOW THESE STEPS WHEN
BATTERY IS INSTALLED IN VEHICLE.
2. Plug the charger AC power cord into the AC outlet.
3. With the charger plugged in and connected to the battery of the vehicle, set the
charge rate selector switch to the engine start position.
4. Crank the engine until it starts or 10 seconds pass. If the engine does not start, wait 3
minutes before cranking again. This allows the charger and battery to cool down.
NOTE: During extremely cold weather, or if the battery is under 2 volts, charge the battery
for 5 minutes before cranking the engine.
5. If the engine fails to start, charge the battery for 5 more minutes before attempting to
crank the engine again.
6. After the engine starts, unplug the AC power cord before disconnecting the battery
clips from the vehicle.
7. Clean and store the charger in a dry location.
NOTE: If the engine does turn over but never starts, there is not a problem with the
starting system; there is a problem somewhere else with the vehicle. STOP cranking the
engine until the other problem has been diagnosed and corrected.
Engine Starting Notes
During the starting sequence listed above, the charger is set to one of three states.
Wait for cranking The charger waits until the engine is actually being cranked before
delivering sufcient charge (up to 50 amps) for engine start. While waiting, the charger
delivers a charge of up to 10 amps, and will go into Abort Mode if the engine is not
cranked within 15 minutes.
Cranking When cranking is detected, the charger will automatically deliver up to its
maximum output as required by the starting system for as long as 10 seconds of cranking.
Cool DownAfter cranking, the charger enters a mandatory 3 minute (180 second) cool
down state. During the cool down period, the charger delivers a charge of up to 10 amps
and the LED will blink slowly (1x per second). After 3 minutes, the LED will start blinking
fast (4x per second), indicating that another crank cycle can be started.
10
12. CALCULATING CHARGE TIME
Use the following table to more accurately determine the time it will take to bring a battery
to full charge. First, identify where your battery ts into the chart.
CCA = Cold Cranking Amps
RC = Reserve Capacity
Ah = Amp hour
NR means that the charger setting is NOT RECOMMENDED.
Find your battery’s rating on the chart below, and note the charge time given for each
charger setting. The times given are for batteries with a 50% charge prior to recharging.
Add more time for severely discharged batteries.
BATTERY SIZE/RATING CHARGE RATE/CHARGING TIME
2 AMP 10 AMP
SMALL
BATTERIES
Motorcycle,
garden tractor, etc.
6 - 12 Ah 2 - 4 hrs NR
12 - 32 Ah 4 - 10 hrs NR
CARS/
TRUCKS
200 - 315 CCA 40 - 60 RC 11 ¼ - 14 ½ hrs 2¼ - 3 hrs
315 - 550 CCA 60 - 85 RC NR 3 - 3¾ hrs
550 - 1000 CCA 80 - 190 RC NR 3¾ - 7 hrs
MARINE/DEEP-CYCLE
80 RC NR 3½ hrs
140 RC NR 5½ hrs
160 RC NR 6 hrs
180 RC NR 6½ hrs
13. MAINTENANCE INSTRUCTIONS
13.1 After use and before performing maintenance, unplug and disconnect the battery charger
(see sections 6, 7 and 8).
13.2 Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clips,
cords, and the charger case.
13.3 Ensure that all of the charger components are in place and in good working condition,
including the plastic boots on the battery clips.
13.4 Servicing does not require opening the unit, as there are no user-serviceable parts.
13.5 All other servicing should be performed by qualied service personnel.
14. MOVING AND STORAGE INSTRUCTIONS
14.1 Store the charger unplugged, in an upright position. The cord will still conduct electricity
until it is unplugged from the outlet.
14.2 Store inside, in a cool, dry place.
14.3 Do not store the clips on the handle, clipped together, on or around metal, or clipped to cables.
14.4 If the charger is moved around the shop or transported to another location, take care to
avoid/prevent damage to the cords, clips and charger. Failure to do so could result in
personal injury or property damage.
11
15. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
The charger will not turn on. Charger is not plugged in.
No power at the receptacle.
Poor electrical connection.
Plug the charger into an AC
outlet.
Check for open fuse or circuit
breaker supplying AC outlet.
Unplug the charger from the
AC outlet, wait 10 seconds,
then plug it back in.
No reading on the Ammeter.
(Needle stays on the left.)
Clips are not making a good
connection to the battery.
Connections are reversed.
Short or bad cell on the
battery.
2 amp charge rate is being
used.
Check for poor connection to
battery and frame.
Unplug the charger and
reverse the clips.
Have the battery checked.
Ammeter may show no
activity at the 2A charge rate.
Ammeter reading
stays high.
Battery is severely
discharged.
Wrong battery voltage.
Continue charging battery for
two more hours. If problem
continues, have the battery
checked.
Verify that the output voltage
of the charger matches the
battery voltage.
Ammeter reads less than
selected charge rate when
charging a discharged
battery.
Extension cord is too long or
wire gauge is too small.
Weak cell or sulfated plate in
battery.
Battery is only partially
discharged.
Use a shorter or heavier
gauge extension cord.
Have the battery checked.
Continue to charge the
battery.
Battery clips do not spark
when touched together.
The charger is equipped
with an auto-start feature.
It will not supply current
to the battery clips until a
battery is properly connected.
The clips will not spark if
touched together.
No problem; this is a normal
condition.
Charger makes a noticeable
buzz.
Transformer laminations
vibrate.
No problem; this is a normal
condition.
12
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Short or no start cycle when
cranking engine.
Drawing more than 50 amps.
Failure to wait 3 minutes
between cranks.
Battery may be severely
discharged.
The charger may be
overheated.
Crank time varies with the
amount of current drawn.
Wait 3 minutes of rest time
before the next crank.
Charge for 10 to 15 minutes
at the 10A rate to help assist
in cranking.
The thermal protector may
have tripped and needs a
little longer to reset.
The measured current is
much lower than what was
selected.
The charger reached the
maximum voltage and is
reducing the current.
No problem; this is a normal
condition.
16. BEFORE RETURNING FOR REPAIRS
16.1 When a charging problem arises, make certain that the battery is capable of accepting a
normal charge. Double check all connections, the AC outlet for a full 120 volts, the charger
clips for correct polarity and the quality of the connections from the cables to the clips and
from the clips to the battery system. The clips must be clean.
16.2 When a battery is very cold, partially charged or sulfated, it will not draw the full rated
amperes from the charger. It is both dangerous and damaging to a battery to force higher
amperage into it than it can effectively use in recharging.
16.3 When an UNKNOWN OPERATING PROBLEM arises, please read this complete manual
and call the customer service number for information. This will usually eliminate the need
for return.
If the above solutions do not eliminate the problem,
or for information about troubleshooting or replacement parts,
call toll-free from anywhere in the U.S.A.
1-800-732-7764
7:00 am to 5:00 pm Central Time, Monday through Friday
Page 1 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 2 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 3 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 4 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 5 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 6 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 7 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 8 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 9 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 10 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 11 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual
Page 12 of 12 - Craftsman Craftsman-Diehard-Automatic-Battery-Charger-10-2-50-Amp-Owners-Manual-  Craftsman-diehard-automatic-battery-charger-10-2-50-amp-owners-manual

Navigation menu