Crate Amplifiers Flexwave 65 112 Users Manual 65/112 Three Channel Guitar Amplifier Owner's

FlexWave 65112 to the manual 15194f93-90ca-44bd-bbad-a8b806dde0d3

2015-02-02

: Crate-Amplifiers Crate-Amplifiers-Flexwave-65-112-Users-Manual-424329 crate-amplifiers-flexwave-65-112-users-manual-424329 crate-amplifiers pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

Three-Channel Guitar Amplifier
with DSP and Channel Tracking

Owner’s Manual

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

TABLE OF CONTENTS
Introduction ............................................................. 3
Channel Tracking ..................................................... 4
The Front Panel ....................................................... 5
The Rear Panel ........................................................ 6
The DSP Section ...................................................... 7
Using the Footswitch with the DSP ............................ 8
Suggested Settings.................................................. 9
System Block Diagram ........................................... 10
Technical Specifications.......................................... 12
Service Information ................................................ 12

CAUTION

PRECAUCION

ATTENTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

RIESGO DE CORRIENTAZO
NO ABRA

RISQUE D'ELECTROCUTION
NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA
LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.

ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.

IMPORTANT SAFETY INSTRUCTIONS
• READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
• DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR
•
•
•
•
•
•
•
•
•
•

PROPER OPERATION, THIS UNIT REQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR
FLOW PROVISIONS IN THE CABINET.
DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND
COMPATIBLE WITH VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR SAFE
OPERATION AND TO AVOID INJURY.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND
PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR
PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
WARNING: THIS UNIT REQUIRES A SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRIC CODES HAVING THE
LINE SUPPLY VOLTAGE, POWER, AND FREQUENCY IDENTIFIED ON THE REAR OF THE UNIT. THE OUTLET MUST REMAIN
ACCESSIBLE TO DISCONNECT THE UNIT IF A FAULT SHOULD ARISE WHILE IN USE. THIS UNIT SHOULD BE UNPLUGGED WHEN
NOT IN USE.
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:

"DANGEROUS VOLTAGE"

“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"

"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"

“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

Introduction
Congratulations! You are now the proud owner of the Crate FlexWave65/112 three-channel
guitar amplifier with advanced digital signal processing (DSP) and Channel Tracking. This rugged amplifier combines outstanding features with serious clean and distorted sounds. Digital
Reverb, Delay, and Modulation effects provide you with a wide variety of sounds. Crate’s
unique Channel Tracking feature automatically stores your DSP settings for each channel to
memory. As you switch from one channel to another, the DSP settings for the selected channel are instantly recalled. The supplied three-button footswitch allows you to select channels
and change the DSP bank (Bank A/Bank B) by “remote control.” A front panel 1/8" stereo
CD input jack allows you to play along with your CD player, MP3 player, or iPod. A rear panel
insert jack allows you to add even more effects by connecting an external effect processor.
Like all Crate products, your FlexWave65/112 amplifier is designed by musicians and built
using only the best components. Extensive testing confirms that this amplifier is the absolute
best it can be.
In order to get the most out of your new amplifier, we strongly urge you to read this manual
before you begin playing.
And thank you for choosing Crate.
Here are some of the features packed into your new FlexWave65/112 Combo Amplifier:
•
65 watts rms power output
•
1 x 12" speaker
•
Three-Channel Operation
—High Gain Channel
—Overdrive Channel
—Clean Channel
• 3-band EQ on the Overdrive and Clean Channels
• Proprietary “Shape” EQ control on the High Gain Channel
• DSP Effects including Delay, Modulation, and Reverb sections
•
CD Input
•
Effects Loop
•
3-Function Footswitch included
•
External Speaker jack
• Built-in Chromatic Tuner

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

Channel Tracking
Your Crate FlexWave65/112 gives you the power of Channel Tracking. Once you select a
DSP setting for each channel, Channel Tracking stores the settings to memory whenever you
change channels. When you go back to that channel, Channel Tracking recalls those DSP settings automatically, without changing the DSP controls!
For example:
• Select the Clean channel. Set the Mod control to “Flanger,” the Delay control to “Medium,”
and adjust the Reverb control to your preference.
• Select the Overdrive channel. Set the Mod control to “Chorus,” the Delay control to “Slap,”
and readjust the Reverb control to a different setting. (The DSP settings for the Clean
channel are now saved to memory.)
• Select the High Gain channel. Set the Mod control to “Phaser,” the Delay control to “Long,”
and readjust the Reverb control once again. (The DSP settings for the Overdrive channel
are now saved to memory.)
• Reselect the Clean channel. (The DSP settings for the High Gain channel are now saved to
memory.)
When you reselected the Clean channel, the DSP settings previously stored in memory were
automatically recalled. Switch to the Overdrive channel and the DSP settings you just stored
are still there. You can change the DSP settings at any time. Once you set the DSP and select
another channel, Channel Tracking stores the settings for you. Even when the amplifier is
turned off, the DSP settings are stored and recalled the next time you turn it on. That’s the
power of Channel Tracking!
In addition, each channel has two DSP banks, Bank A and Bank B, when you use the supplied
three-button footswitch (see page 8 for more information on using the footswitch). Channel
Tracking also remembers which DSP bank was selected for each channel.

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking
The Front Panel
HIGH GAIN
INPUT

GAIN

SHAPE

OVERDRIVE
LEVEL

GAIN

LOW

CLEAN

MID

HIGH

LEVEL

VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

OVERDRIVE

CD
INPUT

HIGH GAIN

LONG
MEDIUM

PHASER

CLEAN

POWER

DELAY
SLAP

FLANGER
CHORUS

OVERDRIVE

1. INPUT: Use this jack to connect your
guitar to the amplifier by means of a shielded instrument cable.
2. HIGH GAIN LED: This LED illuminates
when the High Gain channel is selected.
3. GAIN: Use this control to adjust the amount
of distortion for the High Gain channel.
4. SHAPE: Use this control to “dial in” the
tone for the High Gain channel. Rotating
this control counter-clockwise enhances the
mid frequencies, while rotating it clockwise
enhances the low and high frequencies.
5. LEVEL: Use this control to adjust the output level of the High Gain channel.
6. HIGH GAIN/OVERDRIVE: Use this switch
to select the High Gain or Overdrive channel. With the switch in the out position, the
Overdrive channel is selected. When the
switch is pushed in, the High Gain channel is
selected. Note: This switch is only active when
the Overdrive/Clean switch [13] is pushed in.
7. OVERDRIVE LED: This LED illuminates
when the Overdrive channel is selected.
8. GAIN: Use this control to adjust the amount
of distortion for the Overdrive channel.
9. LOW: This adjusts the bass frequencies.
Use this control to get the best sounding
bass response for your instrument when
using the Overdrive channel.
10. MID: This adjusts the midrange frequencies. Use this control to get the best projection and midrange tones for your instrument
when using the Overdrive channel.
11. HIGH: This adjusts the treble frequencies. Use this control to attain a bright and
lively sound for your instrument when using
the Overdrive channel.
12. LEVEL: Use this control to adjust the
output level of the Overdrive channel.

13 14

13. OVERDRIVE/CLEAN: Use this switch
to select the Clean channel or the Overdrive
and High Gain channels. With the switch in
the out position, the Clean channel is selected. When the switch is pushed in, either the
High Gain or Overdrive channel is selected,
depending on the setting of the High Gain/
Overdrive switch [6].
14. CLEAN LED: This LED illuminates when
the Clean channel is selected.
15. VOLUME: Use this control to adjust the
output level of the Clean channel.
16. LOW: This adjusts the bass frequencies. Use this control to get the best sounding bass response for your instrument when
using the Clean channel.
17. MID: This adjusts the midrange frequencies. Use this control to get the best projection and midrange tones for your instrument
when using the Clean channel.
18. HIGH: This adjusts the treble frequencies. Use this control to attain a bright and
lively sound for your instrument when using
the Clean channel.
19-21. EFFECTS: Use these controls to apply
and adjust the DSP effects. Complete information on these effects is provided on page 7.
22. CD INPUT: Use this 1/8" stereo mini
jack to connect the output from a CD player,
MP3 player, laptop, etc., to the amplifier.
The signal at this jack is summed into a
mono signal, which is sent to the internal
power amp circuit. Use the output level control for the signal source to adjust the signal
for the proper mix with your guitar.
23. POWER: Use this switch to turn the
amplifier on (top of the switch depressed)
and off (bottom of the switch depressed).
The switch illuminates when the amplifier is
turned on.
5

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking
The Rear Panel
24

FOOTSWITCH
EXT
SPKR

DSP

CHANNEL

BANK A
BANK B

CLEAN / OD
HIGH GAIN

INSERT

100 VAC: 250V
T2.5A
120 VAC: 250V
T2A
230/240 VAC: 250V
T1.25A

TIP

RING

30
24. FUSE: The fuse protects the amplifier
28. INSERT: Use this jack to connect an
from damage caused by a faulty AC power
external signal processor to the amplifier. Use
source or other problems. If the fuse opens,
Crate’s STP201, STP202, or STP203 stereoto-mono Y-cord or an adapter such as Crate’s
replace it with the same size and type. If
YPP117 and two 1/4" mono signal cables to
fuses continue to fail, check the AC source. If
connect to the effect, as shown below.
the source is okay, refer to page 12 or contact your Crate dealer for service information.
29. POWER CORD (not shown): This
grounded power cord is to be plugged into
25. EXTENSION SPEAKER: Use this jack
a grounded power outlet, wired to current
to connect the amplifier to an external speakelectrical codes and compatible with the
er cabinet. This jack is wired in series with
voltage, power, and frequency requirements
the internal speaker, which remains active
stated on the rear panel. Do not attempt to
when an extension speaker is connected.
defeat
the safety ground connection!
26. DSP FOOTSWITCH:
Use this jack to connect one of the footswitch
30. ELECTRONIC TUNER (cabinet top)
cables to the three-button footswitch (supThe electronic tuner is active whenever the
plied). This allows you to select between two
amplifier is turned on, providing constant
DSP presets for each of the three channels.
“real-time” tuning. The row of red LEDs on
Additional information about the operation
the left indicates which note is being tuned.
of the footswitch is on
When a single LED is lit,
Stereo-to-mono
Y-cord:
Y-adapter
and
2
cables:
page 8.
it represents the note
TIP
TIP
RETURN
to Insert
to Insert
that appears just below
27. CHANNEL
RING
RING
SEND
jack
jack
SLEEVE GROUND SLEEVE
the LED. When two LEDs
FOOTSWITCH: Use this
are lit, it represents
jack to connect one of
(STP201, 3'
the note that appears
the footswitch cables
(YPP117)
STP202, 6'
STP203, 9')
between them in the
to the three-button footbottom row. The left
switch (supplied). This
green LED indicates the
allows you to remotely
note is flat, and the right
switch between the
green LED indicates the
Clean, High Gain, and
note is sharp. The note
Overdrive channels.
is properly tuned when
(1/4"-TO-1/4"
Additional information
MONO SHIELDED
both LEDs are lit at the
CABLES)
about the operation of
to
to
to
to
same time.
the footswitch is on
effect
effect
effect
effect
"OUT"
"OUT"
"IN"
"IN"
page 8.
RING

TIP

jack

External Effect

jack

External Effect

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking
The DSP Section
EFFECTS
REVERB

MOD
CHORUS

LONG
MEDIUM

PHASER

Signal Path
MOD + DELAY + REVERB

CD
INPUT

19
19. REVERB: Use this control to adjust
the amount of digital reverb effect. In its
fully counterclockwise position, the signal
will be “dry” (without reverb). As you rotate
this control clockwise, the amount of reverb
increases.
20. MOD: Use this control to select the
type of digital modulation effect. In its fully
counterclockwise position, the signal will
be “dry” (without modulation). As you rotate
the control clockwise, you can select from

Effect Setting
Chorus 1
Chorus 2
Chorus 3
Flanger 1
Flanger 2
Flanger 3
Phaser 1
Phaser 2
Phaser 3
Slap 1
Slap 2
Slap 3
Medium 1
Medium 2
Medium 3
Long 1
Long 2
Long 3

POWER

DELAY
SLAP

FLANGER

three chorus settings, three flanger settings,
or three phaser settings. The chart below
describes these effects.
21. DELAY: Use this control to select the
type of digital delay effect. In its fully counterclockwise position, the signal will be “dry”
(without delay). As you rotate the control
clockwise, you can select from three slap
settings, three medium delay settings, or
three long delay settings. The chart below
describes these effects.

Description
Chorus with low depth
Chorus with medium depth
Chorus with high depth
Flanger with low depth
Flanger with medium depth
Flanger with high depth
Phaser with low feedback
Phaser with medium feedback
Phaser with high feedback
Single short delay with low level
Single short delay with medium level
Single short delay with high level
Multiple repeats with low level and medium length
Multiple repeats with medium level and medium length
Multiple repeats with high level and medium length
Multiple repeats with low level and long length
Multiple repeats with medium level and long length
Multiple repeats with high level and long length
7

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking
Using the Footswitch with the DSP
The Crate three-button footswitch supplied with the FlexWave65/112 allows access to an
additional DSP preset for each channel of the amplifier. When the footswitch is connected to
the amplifier as shown below, the “original” DSP presets are active for each channel when the
#3 footswitch LED is illuminated. These are referred to as “DSP Bank A.” When the #3 button
is switched and the LED is off, a second DSP preset may be stored and recalled for each
channel — “DSP Bank B.”
Note: DSP Bank B presets are only accessible when the footswich is connected to the amplifier. When the footswitch is not connected, only DSP Bank A is accessible.

FOOTSWITCH
EXT
SPKR

“LEFT” jack

DSP

CHANNEL

BANK A
BANK B

CLEAN / OD
HIGH GAIN

INSERT

“RIGHT” jack

Switch #3:
LED ON = DSP BANK A
LED OFF = DSP BANK B

Switch #2:
LED ON = HIGH GAIN CH/OVERDRIVE CH
Switch #1:
LED OFF = CLEAN CH
LED ON = HIGH GAIN CH
LED OFF = OVERDRIVE CH
[only when Switch #2 is activated (LED ON)]

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

Suggested Settings
Sweet ‘n Clean:
HIGH GAIN
INPUT

GAIN

OUT

OVERDRIVE

SHAPE

LEVEL

GAIN

LOW

MID

HIGH

LEVEL

CLEAN
VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

OVERDRIVE

POWER

DELAY
SLAP

LONG
MEDIUM

FLANGER
CHORUS

PHASER

CLEAN

CD
INPUT

HIGH GAIN

OVERDRIVE

AS
DESIRED

Just a ‘Lil Nasty:
OUT

HIGH GAIN
INPUT

GAIN

SHAPE

OVERDRIVE

LEVEL

GAIN

LOW

MID

HIGH

LEVEL

CLEAN
VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

OVERDRIVE

POWER

DELAY
SLAP

LONG
MEDIUM

FLANGER
CHORUS

PHASER

CLEAN

CD
INPUT

HIGH GAIN

OVERDRIVE

AS
DESIRED

Politely Gritty:
OUT

HIGH GAIN
INPUT

GAIN

SHAPE

OVERDRIVE

LEVEL

GAIN

LOW

MID

HIGH

LEVEL

CLEAN
VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

POWER

DELAY
SLAP

OVERDRIVE

LONG
MEDIUM

FLANGER
CHORUS

PHASER

CLEAN

HIGH GAIN

CD
INPUT

OVERDRIVE

AS
DESIRED

Down ‘n Dirty:
OUT

HIGH GAIN
INPUT

GAIN

SHAPE

OVERDRIVE

LEVEL

GAIN

LOW

MID

HIGH

LEVEL

CLEAN
VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

OVERDRIVE

POWER

DELAY
SLAP

LONG
MEDIUM

FLANGER
CHORUS

PHASER

CLEAN

HIGH GAIN

CD
INPUT

OVERDRIVE

AS
DESIRED

Mean & Obscene:
IN

HIGH GAIN
INPUT

GAIN

SHAPE

OVERDRIVE

LEVEL

GAIN

LOW

MID

HIGH

LEVEL

CLEAN
VOLUME

LOW

EFFECTS
MID

HIGH

REVERB

MOD

OVERDRIVE

10
HIGH GAIN

CD
INPUT

LONG
MEDIUM

PHASER

CLEAN

POWER

DELAY
SLAP

FLANGER
CHORUS

OVERDRIVE

AS
DESIRED

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

System Block Diagram
TUNER

BUFFER
INPUT
CLEAN

VOLUME LOW MID

HIGH
OVERDRIVE
LEVEL

OVERDRIVE
GAIN

CLEAN/
OVERDRIVE

LOW MID HIGH
OVERDRIVE/
HIGH GAIN

HIGH GAIN
LEVEL
HIGH GAIN
GAIN

SHAPE

MIX
AMP

DSP
FLANGER

PHASER

MEDIUM

INSERT

LONG

POWER
AMP
CHORUS

SLAP

MOD

SPEAKER
DELAY

REVERB

EXT.
SPEAKER

MIX
AMP
CD
INPUT
DAMPING
CIRCUIT

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device not expressly approved by LOUD Technologies Inc. could void
the user's authority to operate the equipment under FCC rules.

Declaration Of Conformity
Manufacturer:

LOUD Technologies Inc.
16220 Wood-Red Rd. NE
Woodinville, WA 98072, USA

Product Name:
Product Type:
Complies with Standards:
LVD:
Safety:
EMC:

Crate FlexWave65/112
Audio Amplifier
92/31/EEC, 93/68/EEC, & 73/23/EWG
EN60065
EN55013, EN55020, EN55022, EN55103, EN61000-3-2,
& EN61000-3-3

The official Declaration of Conformity for this product is kept on file at:
LOUD Technologies Inc., 16220 Wood-Red Road NE, Woodinville, WA 98072 • Tel: 1-866-858-5832

FlexWave65/112 Guitar Amplifier w/DSP and Channel Tracking
FlexWave 65/112 TECHNICAL SPECIFICATIONS:
Output Power Rating

65W rms @ 5% THD, 8Ω, 120 VAC

Gain

110 dB, all controls @ 10
88 dB, all controls @ 10
58 dB, all controls @ 10

High Gain Channel
Overdrive Ch
Clean Ch

CD Input

29 dB

Maximum Input Signal Accepted

2.5 volts rms @ 400 Hz

Input Impedance

470k ohm

High Gain Channel

Shape Control

Proprietary Circuit

Overdrive Channel

Low
Mid
High

20 dB range @ 80 Hz
15 dB range @ 1 kHz
20 dB range @ 10 kHz

Clean Channel

Low
Mid
High

36 dB range @ 80 Hz
15 dB range @ 800 Hz
40 dB range @ 10 kHz

Speaker Size and Rating

12" Crate Custom Design 8 ohm

Power Requirements

120 VAC, 60 Hz, 95 VA
100/115 VAC, 50/60 Hz, 95 VA
230/240 VAC, 50/60 Hz, 95 VA

Size (H x W x D)

17.75 in/45.1 cm x 21.50 in/54.6 cm x
12.50 in/31.8 cm

Weight

36 lb/16.3 kg

The Flex Wave65/112 is covered with a durable Tolex material. Wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
“Crate” is a registered trademark of LOUD Technologies Inc. All other brand names mentioned are trademarks or
registered trademarks of their respective holders and are hereby acknowledged.

Service Information:
If you are having a problem with your Flex Wave65/112, you can go to our website
(www.crateamps.com) and click on Support for service information, or call 1-800-898-3211
during business hours (7 am to 5 pm PST, Monday-Friday). If you are outside of the U.S.,
contact your local distributor for technical support and service.

www.crateamps.com
@2007 LOUD Technologies Inc.
16220 Wood-Red Road NE • Woodinville, WA 98072
Part No. 0022724 Rev. A 01/07

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 for Macintosh
Keywords                        : FlexWave 65/112, FW65/112, Guitar Amplifier, Combo, Crate, LOUD Technologies Inc.
Create Date                     : 2007:01:02 18:29:28-08:00
Modify Date                     : 2007:01:02 18:31:01-08:00
Creator Tool                    : Adobe InDesign CS2 (4.0.3)
Metadata Date                   : 2007:01:02 18:31:01-08:00
Format                          : application/pdf
Creator                         : Crate
Title                           : FlexWave 65/112 Three-Channel Guitar Amplifier Owner's Manual
Description                     : Crate FlexWave 65/112
Subject                         : FlexWave 65/112, FW65/112, Guitar Amplifier, Combo, Crate, LOUD Technologies Inc.
Document ID                     : uuid:4517f035-9ad2-11db-9bc1-001451113ce4
Instance ID                     : uuid:73e94319-9ad2-11db-a9cb-001451113ce4
Page Count                      : 12
Author                          : Crate

EXIF Metadata provided by EXIF.tools

Crate Amplifiers Flexwave 65 112 Users Manual 65/112 Three Channel Guitar Amplifier Owner's

FlexWave 65112 to the manual 15194f93-90ca-44bd-bbad-a8b806dde0d3

Navigation menu

Versions of this User Manual:

Views

Navigation