Crestron Electronics CWD7134 Two-Way RF Transceiver Module User Manual CWD7134 Doc 7497B

Download:
Mirror Download [FCC.gov]
Document ID	1914287
Application ID	tjx8WszNKACZk5k2xbb5fQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.4kB (217558 bits)
Date Submitted	2013-03-08 00:00:00
Date Available	2013-03-08 00:00:00
Creation Date	2017-10-28 04:57:56
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-28 04:57:56
Document Title	Microsoft Word - CWD7134_Doc. 7497B.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Crestron Electronics, Inc.

Crestron CWD7134
Two-Way RF Transceiver Module
Operations Guide
Regulatory Compliance
Federal Communications Commission (FCC) Compliance Statement
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
This radio transmitter, IC: 5683C-CWD7134, has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Antenna Type: SMD, Maximum permissible antenna gain: 1.8 dBi, Impedance: 50 Ohms
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que
la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
Le présent émetteur radio , IC: 5683C-CWD7134, a été approuvé par Industrie Canada pour fonctionner avec les types
d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.
Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Type d'antenne: SMD, Gain admissible maximal: 1.8 dBi, Impédance: 50 Ohms
To satisfy RF exposure requirements, this device and its antenna must operate with a separation distance of at least 20
centimeters from all persons and must not be collocated or operating in conjunction with any other antenna or
transmitter.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
Crestron CWD7134
Two-Way RF Transceiver Module
Contents
Two-Way RF Transceiver Module: CWD7134 ..............................................1
Functions and Features .............................................................................................................. 1
Specifications............................................................................................................................. 2
Physical Description – CWD7134 with External Antenna ........................................................ 3
Ports............................................................................................................................. 4
Power/I-O .................................................................................................................... 4
Setup .......................................................................................................................................... 5
Labeling ..................................................................................................................................... 5
Documentation ........................................................................................................................... 5
Operations Guide - DOC. 7497B
Contents  i
Crestron CWD7134
Two-Way RF Transceiver Module
Two-Way RF Transceiver Module:
CWD7134
Functions and Features
The CWD7134 (hereafter referred to as “module”), with an external SMD antenna assembly or an
integrated SMD antenna, is a two-way radio frequency (RF) module that utilizes the 2.4 GHz
frequency band to communicate with other devices.
The module operates according to the IEEE 802.15.4 specification and can be configured to minimize
the possibility of interference with other devices.
The module receives RF signals from one or more Crestron devices and can transmit these signals over
the air for further processing (depending on the application).
Functional Summary



Operations Guide - DOC. 7497B
2.4 GHz frequency band, IEEE 802.15.4 specification
Range from 3 feet to 550 feet
Operates on one of sixteen available channels to establish optimal signal
quality
Two-Way RF Transceiver Module: CWD7134  1
Two-Way RF Transceiver Module
Crestron CWD7134
Specifications
The table below is a summary of specifications for the CWD7134.
Specifications of the CWD7134
SPECIFICATION
DETAILS
Power Requirements
1.3 watts (5 Vdc @ 0.26 A)
Operating Frequency
2400 MHz to 2483.5 MHz (802.15.4 compliant)
Operating Ranges*
Minimum Distance
3 feet
Maximum Distance Indoors
(without repeater device)
550 feet
Available Channels
16 (numbered 11 through 26 per 802.15.4)
External Antenna
Max. Gain:
1.8 dBi
(Crestron Model
CSA-ANT-EXTRNL-QMT50-W)
Average Gain:
-1.9 dBi
Type:
SMD
Frequency:
2.4 GHz to 2.5 GHz
Connector Type: MMCX Plug Reverse
Polarity Connector with
SPDT RF Switch
Internal Antenna**
Dimensions
Max. Gain:
2.1 dBi
Average Gain:
-1.2 dBi
Type:
SMD
Frequency:
2.4 GHz to 2.5 GHz
Width:
2.10 in (5.33 cm)
Height:
2.20 in (5.58 cm)
Depth:
0.60 in (1.52 cm)
The location and orientation of the module are important factors in the RF performance. With the unit located outside of
any metal enclosures, the antenna is adjusted to achieve the best range. The range is dependent on its placement and the
building in which it is used. The construction of the building, obstructions, and RF interference from other devices are
factors determining the effective range of the unit. To prevent unit-to-unit RF interference, multiple modules operating at
the same frequencies should not be installed within 3 – 5 feet of each other.
** The internal antenna is automatically disconnected when an external antenna is connected to MMCX antenna port.
2  Two-Way RF Transceiver Module: CWD7134
Operations Guide - DOC. 7497B
Crestron CWD7134
Two-Way RF Transceiver Module
Physical Description – CWD7134 with External Antenna
The module, shown below, consists of various components attached to a printed circuit board. The
circuit board attaches an intended SMD mounting antenna. A MMCX reverse polarity female antenna
port is located at the edge of the circuit board for attaching an optional SMD antenna assembly while a
8-pin single row male connector and a 4-pin single row male connector are provided for the
application-specific installation.
The reverse polarity MMCX antenna port includes a SPDT switch that disconnects the internal SMD
antenna when the external SMD antenna assembly is connected.
Physical View of External Antenna Assembly CSA-ANT-EXTRNL-QMT50-W
Physical View of CWD7134
Operations Guide - DOC. 7497B
Two-Way RF Transceiver Module: CWD7134  3
Two-Way RF Transceiver Module
Crestron CWD7134
CWD7134 Detail Views
Ports
The module contains a 4-pin male header for application power and a 8-pin male header for application
I/O. A 10-pin debug header is also provided. Refer to the diagrams and descriptions that follow.
Power/I-O
The 8-pin male connector provides power to the module as well as the communication between the
module and wired devices. Refer to the following table for pin assignments of the module interface
connector.
The 4-pin male connector provides power connections for the wired devices connected to the module.
NOTE: Pins 3 and 4 on the 8-pin connector provide power to the module.
NOTE: Pins 1 and 4 on the 4-pin connector are connected to pins 1 and 2 on the 8-pin connector
through protection circuitry. These pins act as a pass through for power to be supplied to the wired
devices.
Power/I-O Pinout Signals
8-Pin Connector
Pin #
Signal
4-Pin Connector
Pin #
Signal
Pin #
Signal
24V
PB1/TXD
24V
GND
PB2/RXD
No Connect
GND
PC7 OUTPUT
No Connect
5V
PC6 INPUT
GND
4  Two-Way RF Transceiver Module: CWD7134
Operations Guide - DOC. 7497B
Crestron CWD7134
Two-Way RF Transceiver Module
Setup
Refer to the hookup diagram below, which shows the connections made to the module. Complete the
connections in any order.
NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies
should not be installed within 3 to 5 feet of each other.
Hardware Hookup
Labeling
If the FCC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: EROCWD7134” or “Contains FCC ID: EROCWD7134.” Any similar wording that
expresses the same meaning may be used.
Documentation
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user manual of the end product.
The user manual for OEM integrators must include the following information in a prominent location.
“IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.”
Operations Guide - DOC. 7497B
Two-Way RF Transceiver Module: CWD7134  5
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Operations Guide – DOC. 7497B
02.13
Specifications subject to
change without notice.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Author                          : Crestron Electronics, Inc.
Create Date                     : 2013:02:26 11:51:17-05:00
Modify Date                     : 2013:02:26 11:52:54-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 10.1.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:02:26 11:52:54-05:00
Format                          : application/pdf
Title                           : Microsoft Word - CWD7134_Doc. 7497B.doc
Creator                         : Crestron Electronics, Inc.
Document ID                     : uuid:98562328-676a-4040-a794-4cc1dbcd20a9
Instance ID                     : uuid:38ff8b66-eeba-4d47-b6bb-bae268bbd1e5
Page Layout                     : SinglePage
Page Count                      : 10

EXIF Metadata provided by EXIF.tools