Crestron Electronics CWDHR Two-Way RF Transceiver Module User Manual CWDHR 7657A
Crestron Electronics Inc Two-Way RF Transceiver Module CWDHR 7657A
Manual
Crestron CWDHR Two-Way RF Transceiver Module Operations Guide The specific patents that cover Crestron products are listed at patents.crestron.com. Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. This document was written by the Technical Publications department at Crestron. ©2014 Crestron Electronics, Inc. Crestron CWDHR Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: CWDHR .................................................1 Introduction ............................................................................................................................... 1 Specifications............................................................................................................................. 2 Physical Description .................................................................................................................. 3 Setup .......................................................................................................................................... 4 Labeling ..................................................................................................................................... 5 Documentation ........................................................................................................................... 5 Operations Guide - DOC. 7657A Contents i Crestron CWDHR Two-Way RF Transceiver Module Two-Way RF Transceiver Module: CWDHR Introduction The CWDHR (hereafter referred to as “module”), with an SMD antenna, is a two-way radio frequency (RF) module that utilizes the 2.4 GHz frequency band to communicate with other devices. There are two versions: PA07414 and PA07424. The module operates according to the IEEE 802.15.4 specifications. The module receives RF signals from one or more Crestron devices and can transmit these signals over the air for further processing (depending on the application). Features and Functions 2.4 GHz frequency band, IEEE 802.15.4 specification Range from 3 feet to 550 feet. Operates on one of 16 available channels to establish optimal signal quality Operations Guide - DOC. 7657A Two-Way RF Transceiver Module: CWDHR 1 Two-Way RF Transceiver Module Crestron CWDHR Specifications Specifications for the CWDHR are listed in the following table. CWDHR Specifications SPECIFICATIONS Power Requirements Four (4) disposable 1.5 V “AAA” alkaline batteries Operating Frequency 2400 MHz to 2483.5 MHz (802.15.4 compliant) Operating Ranges* Minimum Distance Maximum Distance Indoors (without repeater device) 3 feet 550 feet Available Channels 16 (numbered 11 through 26 per 802.15.4) Serial Communications SPI, 3.0 Vdc Nominal Antenna Gain 2.5 dBi max. peak Type Ceramic chip antenna Frequency 2.4 GHz to 2.5 GHz Dimensions (PA07414) Height 1.850 in Width 0.303 in Depth 7.248 in Dimensions (PA07424) Height DETAILS 1.850 in Width 0.303 in Depth 5.967 in The location and orientation of the module are important factors in RF performance. With the unit located outside of any metal enclosures, the antenna is adjusted to achieve the best range. The range is dependent on its placement and the building in which it is used. The construction of the building, obstructions, and RF interference from other devices are factors determining the effective range of the unit. To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within 3-5 feet of each other. 2 Two-Way RF Transceiver Module: CWDHR Operations Guide - DOC. 7657A Crestron CWDHR Two-Way RF Transceiver Module Physical Description The module, shown below, consists of various components attached to a printed circuit board (PCB). The SMD antenna is soldered to the PCB. Physical View of CWDHR (PA07414) Physical View of CWDHR (PA07424) Operations Guide - DOC. 7657A Two-Way RF Transceiver Module: CWDHR 3 Two-Way RF Transceiver Module Crestron CWDHR Setup Refer to the following diagram. P1 is the interface port. J1 is the antenna port. NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within 3-5 feet of each other. P1 Pin out Signals Pin # Signal Pin # Signal +3.0V JTDO \JRST JTDI AGND JTCK JTMS \RESET PA4 / PTI_EN 10 PA5 / PTI_DATA 4 Two-Way RF Transceiver Module: CWDHR Operations Guide - DOC. 7657A Crestron CWDHR Two-Way RF Transceiver Module Labeling The host device shall be properly labeled to identify the modules within the host device. The FCC and Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device. Otherwise the host device must be labeled to display the FCC and Industry Canada certification numbers of the module, preceded by the words “Contains Transmitter Module” or the word “Contains”, or similar wording expressing the same meaning as follows: Contains FCC ID: EROCWDHR Contains IC: 5683C-CWDHR Documentation The OEM integrator must be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user’s manual for OEM integrators must include the following information in a prominent location: IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Operations Guide - DOC. 7657A Two-Way RF Transceiver Module: CWDHR 5 Two-Way RF Transceiver Module Crestron CWDHR This page is intentionally left blank. 6 Two-Way RF Transceiver Module: CWDHR Operations Guide - DOC. 7657A Crestron CWDHR Two-Way RF Transceiver Module This page is intentionally left blank. Operations Guide - DOC. 7657A Two-Way RF Transceiver Module: CWDHR 7 Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 7657A 10.14 Specifications subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : glin Create Date : 2014:10:30 11:45:46-04:00 Modify Date : 2014:10:30 11:45:46-04:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : glin Title : Microsoft Word - CWDHR_7657A Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 10.1.3 (Windows) Document ID : uuid:e318e09a-d98f-40e3-b1ec-d441d7fef581 Instance ID : uuid:2673d257-13c4-4309-a244-0d5b667927e4 Page Count : 12EXIF Metadata provided by EXIF.tools