Current Technologies 6030A CURRENT Gateway-Bridge OH 6030 User Manual
Current Technologies, LLC CURRENT Gateway-Bridge OH 6030
Contents
- 1. Install Guide
- 2. Notching Instructions
Notching Instructions
Network Element Notching Instructions CURRENT Group, LLC Network Element Notching Instructions 1. Notching Overview In order to comply with FCC requirements on mitigation and avoidance measures it is necessary for the administrator to be able to track the notching on any CURRENT Group unit. Depending on the results, the administrator may need to modify the notching settings. Notching scripts reside on the NEC server in the CURRENT Group BPL system. The administrator is able to access and run these scripts by logging in to the NEC server. The administrator then enters the appropriate command to run the pertinent script. The scripts are described in further detail below. 1.1 Get Notching Settings The administrator logs into the NEC server and follows the steps listed below to obtain the notch settings for a particular CURRENT Group unit. The administrator will need the following parameters in order to run the script: -s= serial number of the unit. This is used to calculate the SNMP pass phrase. -i = IP address of the unit from which you want the current settings. 1. At the Unix command line enter: get_notching –s -I The executed script will return the notching values currently set on the selected unit. The output is displayed as a list of 84 characters, and whether or not the carrier is currently enabled, where 1 = enabled, and 0 = disabled. 1.2 Set Notching Settings The administrator logs into the NEC server and follows the steps listed below to set the notching settings for a particular CURRENT Group unit. The administrator will need the following parameters in order to run the script: -s = serial number of the unit. This is used to calculate the SNMP pass phrase. -i = IP address of the unit to be modified. -C = comma separated list of carriers. Carriers are listed as 1 through 84. 1. At the Unix command line enter: set_notching –s -i -C The executed script will set all carriers to be enabled except for the HAM band and any other carriers specified. If this script is run without specifying any carriers, then the notching is set to the default setting with only the HAM band set to be disabled. February 29, 2008 CURRENT Group, LLC Network Element Notching Instructions 1.3 Calculating The Carrier to Notch The correspondence between carrier number and carrier frequency is shown for both the low voltage and medium voltage domains in the table below. Carrier Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Low Voltage Center Frequency (MHz) 4.4922 4.6875 4.8828 5.0781 5.2734 5.4688 5.6641 5.8594 6.0547 6.2500 6.4453 6.6406 6.8359 7.0313 7.2266 7.4219 7.6172 7.8125 8.0078 8.2031 8.3984 8.5938 8.7891 8.9844 9.1797 9.3750 9.5703 9.7656 9.9609 10.1563 10.3516 10.5469 10.7422 10.9375 11.1381 11.3281 11.5234 11.7188 11.9141 12.1094 12.3047 12.5000 Medium Voltage Center Frequency (MHz) 47.7656 47.5703 47.3750 47.1797 46.9844 46.7891 46.5937 46.3984 46.2031 46.0078 45.8125 45.6172 45.4219 45.2266 45.0312 44.8359 44.6406 44.4453 44.2500 44.0547 43.8594 43.6641 43.4687 43.2734 43.0781 42.8828 42.6875 42.4922 42.2969 42.1016 41.9062 41.7109 41.5156 41.3203 41.1197 40.9297 40.7344 40.5391 40.3437 40.1484 39.9531 39.7578 Continued Æ February 29, 2008 CURRENT Group, LLC Network Element Notching Instructions Carrier Number 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 February 29, 2008 Low Voltage Center Frequency (MHz) 12.6953 12.8906 13.0859 13.2813 13.4766 13.6719 13.8672 14.0625 14.2578 14.4531 14.6844 14.8438 15.0391 15.2344 15.4297 15.6250 15.8203 16.0156 16.2109 16.4063 16.6016 16.7969 16.9922 17.1875 17.3828 17.5781 17.7734 17.9688 18.1641 18.3594 18.5547 18.7500 18.9453 19.1406 19.3359 19.5313 19.7266 19.9219 20.1172 20.3125 20.5078 20.7031 Medium Voltage Center Frequency (MHz) 39.5625 39.3672 39.1719 38.9766 38.7812 38.5859 38.3906 38.1953 38.0000 37.8047 37.5734 37.4141 37.2187 37.0234 36.8281 36.6328 36.4375 36.2422 36.0469 35.8516 35.6562 35.4609 35.2656 35.0703 34.8750 34.6797 34.4844 34.2891 34.0937 33.8984 33.7031 33.5078 33.3125 33.1172 32.9219 32.7266 32.5312 32.3359 32.1406 31.9453 31.7500 31.5547 CURRENT Group, LLC Network Element Notching Instructions 1.4 Calculating Notching Depth To create the appropriate notching depth, it may be necessary to notch more than one carrier. To create a notch >10 dB deep, only a single carrier need be notched. To create a notch >20 dB deep, it is necessary to notch 6 additional carrier on either side of the center frequency of interest. Example: In order to create a notch of >20 dB at a frequency of 5.86 MHz, it is necessary to notch carriers 2-7 and 9-14 in addition to carrier 8. To achieve this, the following command would be entered at the NEC command line interface: set_notching –s -i -C 2,3,4,5,6,7,8,9,10,11,12,13,14 February 29, 2008
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2008:03:05 16:29:34-05:00 Create Date : 2008:03:05 16:29:34-05:00 Format : application/pdf Title : untitled Producer : Acrobat Distiller 8.0.0 (Windows) Document ID : uuid:84eb49b7-1473-4b01-999e-229a959b5983 Instance ID : uuid:18777d46-0f18-4ee4-a0b6-405b8a7cb502 Page Count : 5EXIF Metadata provided by EXIF.tools