CyberTAN Technology MM300C Bluetooth 2.0+ EDR Module User Manual manual

CyberTAN Technology Inc. Bluetooth 2.0+ EDR Module manual

manual

MM300-C / Bluetooth 2.0+ EDR Module MM300-C Bluetooth 2.0+ EDR Module User Manual Rev 0.1
MM300-C / Bluetooth 2.0+ EDR Module National Communications Commission Interference Statement This equipment includes wireless RF module, and must be labeled in a visible area with the following: Contains NCC ID: XXXyyyLPDzzzz-x
MM300-C / Bluetooth 2.0+ EDR Module ii Table of contents Introduction…………………………………………… 1 Install Bluetooth……………………………………… 2
MM300-C / Bluetooth 2.0+ EDR Module 1 Chapter 1 Introduction Thank you for using the Bluetooth Module. The MM300-C is a Bluetooth adapter that works on Bluetooth operation everywhere in the world. It is Bluetooth 2.0+ EDR. MM300-C can give users of laptops, note-books, tablet PCs, and other mobile computing devices access anywhere in the world through any Bluetooth network devices. Able to provide Bluetooth real world throughput. The MM300-C provides the freedom to work as you wish, wherever you wish, using whatever kind of Bluetooth application you wish to use. It is ready to work “out of the box” in any embedded device or in any computer running Microsoft® Windows Vista, or XP. The MM300-C Module is truly a “must-have” for every productivity-sensitive laptop, notebook, or tab-let PC user and any bandwidth-sensitive embedded design. Features and Benefits • Seamless Wireless Connectivity Bluetooth v2.0+EDR supports the use of most recent user-end devices.
MM300-C / Bluetooth 2.0+ EDR Module 2 Chapter 2 Install Bluetooth MM300-C also support Bluetooth function. Below shows how to install Bluetooth device. 4.1 How to install Bluetooth device
3
MM300-C / Bluetooth 2.0+ EDR Module 4
5
MM300-C / Bluetooth 2.0+ EDR Module 6 Appendix A 1. Common Physical Layer Specifications Table 1: Common Physical Layer Specifications Operating Frequency 2402MHz to 2480MHz Bluetooth Tx Power (Typical) 2±2dBm Bluetooth Rx Sensitivity (typical) -42dBm Carrier Spacing 1.0MHz Channel 79 Duplexing TDD Symbol Rate 1Mbps (GFSK) 2Mbps (π/4-DQPSK) 3Mbps (8DPSK) Modulation Method GFSK BT = 0.5 ?/4DQPSK 8DPSK Reference Oscillator 26MHz (built in) RF input and output impedance Nominal 50 ohm Main Chip CSR BC41B143A Dimensions 25.0 x 12.0 x 2.6 mm (typical) GP Compliance Yes
FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance."

Navigation menu