CyberTAN Technology MW302P 11M WLAN PCI Adapter User Manual Manual

CyberTAN Technology Inc. 11M WLAN PCI Adapter Manual

Manual

Download: CyberTAN Technology MW302P 11M WLAN PCI Adapter User Manual Manual
Mirror Download [FCC.gov]CyberTAN Technology MW302P 11M WLAN PCI Adapter User Manual Manual
Document ID330662
Application IDcdFDOOkMXirf1Dfe15sWxQ==
Document DescriptionManual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize69.76kB (871951 bits)
Date Submitted2003-06-06 00:00:00
Date Available2003-06-06 00:00:00
Creation Date2003-05-14 22:47:45
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2003-06-05 22:03:43
Document TitleManual
Document CreatorAcrobat PDFMaker 5.0 for Word

IEEE802.11b WLAN PCI
Adapter
User’s Manual
Rev 0.9
WLAN PCI Adapter User’s Manual
Regulatory compliance
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
This transmitter must not be co-located or operation in conjunction with any other
antenna or transmitter.
WLAN PCI Adapter User’s Manual
About this manual
This User’s Manual describes how to install and operate your IEEE802.11b WLAN
PCI Card. Please read this manual before you install the product.
This manual includes the following topics:
Product description and features.
Hardware installation procedure.
Software installation procedure.
FAQ
WLAN PCI Adapter User’s Manual
Table of Contents
Regulatory compliance............................................................. 2
About this manual ..................................................................... 3
Chapter 1 - Introduction ........................................................... 5
Features................................................................................. 5
What is Wireless LAN? .......................................................... 6
Wireless LAN Modes ............................................................. 6
Notes on Wireless LAN Configuration ................................... 7
Chapter 2 - Hardware Installation ............................................ 8
Package Contents.................................................................. 8
System Requirements for the Card ....................................... 8
Install the PCI Adapter ........................................................... 8
LED Indicators ....................................................................... 9
Connecting the adjustable Antenna to the Card .................. 10
Chapter 3 – Driver Installation for Windows......................... 11
Driver installation for Windows 98 ....................................... 11
Driver installation for Windows 2000 ................................... 14
Driver installation for Windows ME ...................................... 17
Driver installation for Windows XP....................................... 19
Chapter 4 – Installing and Using the Wireless Utility .......... 21
Installation in Windows ........................................................ 21
Using Wireless Utility In Windows XP.................................. 24
Use Windows Wireless Network Configuration .......................... 24
Use Wireless LAN Utility ............................................................ 27
Use Wireless LAN Utility In Windows 98, 2000 and ME ............. 30
Configuring the IEEE802.11b WLAN PCI Card ................... 30
Chapter 5 – Installing Network Protocols ............................. 35
Installing the Network Protocols for Windows 98 and
Millennium............................................................................ 35
Appendix A – FAQ ................................................................... 38
Appendix B – Specifications .................................................. 39
WLAN PCI Adapter User’s Manual
Chapter 1 - Introduction
Thank you for purchasing the IEEE802.11b WLAN PCI Card. This high-speed
IEEE802.11b WLAN PCI Card provides you with an innovative wireless networking
solution. The Card is easy to set up and use. With this innovative wireless technology,
you can share files and printers on the network—without inconvenient wires!
The Card is a network Adapter with a rate of 1, 2, 5.5, and 11 Mbps operating in
the ISM band using Direct Sequence Spread Spectrum (DSSS) transmission
implementing the IEEE 802.11b standard. This Adapter provides Device Drivers
for Windows Operating Systems. It also provides tools for the configuration of the
Card. The tool, as well as the installation steps of the plug-and-play procedure for
the Windows operating systems, is described in this document.
Features
The IEEE802.11b WLAN PCI Card offers compliance with the IEEE 802.11b
specification. This feature allows them to communicate with other wireless
devices that support the standard. Features of the Card are:
Uses 2.4GHz frequency band, which complies with worldwide
requirement
Wireless interface following the IEEE 802.11b standard
Using PCI interface
Enciphering/deciphering of wireless data by the implementation of the
WEP algorithm
Wire-free access to networked resources from anywhere beyond the
desktop
Allows users move between Access Points without resetting their
connection reconfiguration
Delivers data rate up to 11 Mbps
Supports 11, 5.5, 2, and 1 Mbps rates
Provide IEEE802.11b WLAN PCI Card Configuration utility
The Card uses external Antenna with LEDs indicating Power and Link
Supports most popular operating systems
WLAN PCI Adapter User’s Manual
What is Wireless LAN?
Wireless Local Area Network (WLAN) systems offer a great number of
advantages over traditional wired systems. WLAN is flexible and easy to setup
and manage. They are also more economical than wired LAN systems.
Using radio frequency (RF) technology, WLAN transmit and receive data through
the air. WLAN combine data connectivity with user mobility. For example, users
can roam from a conference room to their office without being disconnected from
the LAN.
Using WLAN, users can conveniently access-shared information, and network
administrators can configure and augment networks without installing or moving
network cables.
WLAN technology provides users with many convenient and cost saving features:
•
Mobility: WLAN provide LAN users with access to real-time information
anywhere in their organization, providing service opportunities that are
impossible with wired networks.
•
Ease of Installation: Installing is easy for novice and expert users alike,
eliminating the need to install network cables in walls and ceilings.
•
Scalability: WLAN can be configured in a variety of topologies to adapt to
specific applications and installations. Configurations are easily changed
and range from peer-to-peer networks suitable for a small number of users
to full infrastructure networks of thousands of users roaming over a broad
area.
Wireless LAN Modes
Wireless LANs can be configured in one of two ways:
Ad-hoc
Networking
Also known as a peer-to-peer network, an ad-hoc
network is one that allows all workstations and
computers in the network to act as servers to all other
users on the network. Users on the network can share
files, print to a shared printer, and access the Internet
with a shared modem. However, with ad-hoc
networking, users can only communicate with other
wireless LAN computers that are in the wireless LAN
workgroup, and are within range.
Infrastructure
Networking
Infrastructure
networking
differs
from
ad-hoc
networking in that it includes an access point. Unlike
the ad-hoc structure where users on the LAN contend
the shared bandwidth, on an infrastructure network the
access point can manage the bandwidth to maximize
WLAN PCI Adapter User’s Manual
bandwidth utilization.
Additionally, the access point enables users on a
wireless LAN to access an existing wired network,
allowing wireless users to take advantage of the wired
networks resources, such as Internet, email, file
transfer, and printer sharing.
Infrastructure networking has the following advantages
over ad-hoc networking:
•
Extended range: each wireless LAN computer
within the range of the access point can
communicate with other wireless LAN computers
within range of the access point.
•
Roaming: the access point enables a wireless
LAN computer to move through a building and still
be connected to the LAN.
•
Wired to wireless LAN connectivity: the access
point bridges the gap between wireless LANs and
their wired counterparts.
Notes on Wireless LAN Configuration
When configuring a wireless LAN (WLAN), be sure to note the following points:
•
Optimize the performance of the WLAN by ensuring that the distance
between access points is not too far. In most buildings, WLAN Adapters
operate within a range of 100 ~ 300 feet, depending on the thickness and
structure of the walls.
•
Radio waves can pass through walls and glass but not metal. If there is
interference in transmitting through a wall, it may be that the wall has
reinforcing metal in its structure. Install another access point to circumvent
this problem.
•
Floors usually have metal girders and metal reinforcing struts that interfere
with WLAN transmission.
This concludes the first chapter.
installation of the Card.
The next chapter deals with the hardware
WLAN PCI Adapter User’s Manual
Chapter 2 - Hardware Installation
This chapter covers connecting your IEEE802.11b WLAN PCI Card to PCI slot of
desktop PC.
Package Contents
Please make sure that items below are included on package.
One IEEE802.11b WLAN PCI Card
One Driver / Utility CD-ROM (this user’s manual included)
One Quick Installation Guide
One external antenna
System Requirements for the Card
Operating System: Microsoft Windows 95/98/ME/2000/NT4.0/XP
Desktop PC with CD-ROM drive
One free PCI slot
Pentium-Class 90MHz or higher
Install the PCI Adapter
NOTE: These instructions apply to most desktop computers. For detailed
information on inserting PCI Adapter into your desktop PC, consult the desktop
PC User’s Manual.
SMA Connector
LEDs
PCI Interface
golden fingers
The IEEE802.11b WLAN PCI Card
WLAN PCI Adapter User’s Manual
1. Turn off the computer‚ unplug the power cord and remove the computer's
cover.
2. Pick a free PCI expansion slot and remover the protective bracket.
3. Insert the Card into the slot until it is fully seated.
4. Secure the Card bracket with the screw from step 2.
5. Replace the computer’s cover.
6. Reconnect the power cord and turn on the computer.
LED Indicators
SMA Connector
LINK
POWER
Side view of the PCI Card from bracket.
The following table describes the meaning of LED indicators:
LED
MEANING
POWER
Indicates that the Card is powered on (solid green).
LINK
Indicates link status. The LED lights up (solid green) while
the wireless connection is linked. The LED is blinking green
while wireless data transmitting / receiving.
WLAN PCI Adapter User’s Manual
Connecting the adjustable Antenna to the Card
After installing the Card on computer, connect external Antenna to the Card from the SMA
connector. Hold the antenna in the desired orientation and then turn the lock nut
clockwise until snug (do not over tighten the nut). To adjust the antenna direction, turn the
nut counter clockwise one full turn, adjust the antenna and then tighten the nut.
SMA Connector
After hardware installation is completed, please go to Chapter 3 to install driver on
different Operating System.
10
WLAN PCI Adapter User’s Manual
Chapter 3 – Driver Installation for Windows
The following sections cover IEEE802.11b WLAN PCI Card driver installation in the
Windows Operating Systems.
Note: You have to install your hardware first before you begin to install the drivers.
Driver installation for Windows 98
Follow the steps below to install the IEEE802.11b WLAN PCI Card drivers for
Windows 98.
1. Insert the IEEE802.11b WLAN PCI Card to PCI slot of desktop PC first. (Refer to
Chapter 2 – Hardware installation.)
2. After Windows 98 detects the IEEE802.11b WLAN PCI Card, the Add New
Hardware Wizard window appears. Clicks Next to continue the installation.
3. A screen appears prompting you to select an installation method. Select Search for
the best driver for your device. (Recommended) and click Next to continue.
11
WLAN PCI Adapter User’s Manual
4. Ensure that the CD-ROM drive is selected. Inserts the driver CD-ROM into your
CD-ROM drive and clicks Next to continue.
5. The following screen appears showing the driver search result. Click Next to
continue the installation.
12
WLAN PCI Adapter User’s Manual
6. Windows 98 copies files to your hard disk. The following screen will appear to
inform you when the software installation has finished. Click Finish to finish the
installation.
7. The following screen will ask you to restart your computer to finish the installation.
Click Yes to reboot the system. After system reboot, the Wireless LAN Utility will be
installed automatically. Please go to Chapter 4 to install the utility.
13
WLAN PCI Adapter User’s Manual
NOTE: In most cases, Windows will automatically copy all of the files needed for
networking. If Windows asks you for the files and prompts you to input the path to the
files. Follow the instructions on your screen, and then click OK to continue.
Driver installation for Windows 2000
Follow the steps below to install the IEEE802.11b WLAN PCI Card drivers for
Windows 2000.
1. Insert the IEEE802.11b WLAN PCI Card to PCI slot of desktop PC first. (Refer to
Chapter 2 – Hardware installation.)
2. After Windows 2000 detects the IEEE802.11b WLAN PCI Card, the Found New
Hardware Wizard window appears. Click Next to start the installation.
14
WLAN PCI Adapter User’s Manual
3. A screen appears prompting you to select an installation method. Select Search
for a suitable driver for my device (recommended) and click Next to continue.
4. Ensure that the CD-ROM driver is selected and insert the driver CD-ROM into
your CD-ROM drive and click Next to continue.
15
WLAN PCI Adapter User’s Manual
5. The following screen appears showing the driver search result. Click Next to
continue the installation.
6. The following screen appears. Click Yes to continue
7. The Windows has finished installing software for the device. Click Finish to finish
the installation.
16
WLAN PCI Adapter User’s Manual
Then system will start to install Wireless LAN Utility. Please refer to procedures at
Chapter 4.
Driver installation for Windows ME
Follow the steps below to install the IEEE802.11b WLAN PCI Card drivers for
Windows ME.
1. Insert the IEEE802.11b WLAN PCI Card to PCI slot of desktop PC first. (Refer to
Chapter 2 – Hardware installation.)
2. After Windows ME detects the IEEE802.11b WLAN PCI Card, the Add New
Hardware Wizard window appears. Select Automatic search for a better driver
(Recommended) and insert the driver CD-ROM into CD-ROM drive and click Next
to continue.
17
WLAN PCI Adapter User’s Manual
3. The system will find the setup files and follow the instruction to copy files to your
hard disk. The following screen will appear when the software installation has
finished. Click Finish to finish the installation.
4. The following screen will ask you to restart your computer to finish the hardware
setting up. Click Yes to reboot the system. After system reboot, the Wireless LAN
Utility will be installed automatically. Please go to Chapter 4 to install the utility.
18
WLAN PCI Adapter User’s Manual
NOTE: In most cases, Windows will automatically copy all of the files needed for
networking. If Windows asks you for the files and prompts you to input the path to the
files. Follow the instructions on your screen, and then click OK to continue.
Driver installation for Windows XP
Follow the steps below to install the IEEE802.11b WLAN PCI Card drivers for
Windows XP.
1.
Insert the IEEE802.11b WLAN PCI Card to PCI slot of desktop PC first. (Refer to
Chapter 2 – Hardware installation.)
2.
After Windows XP detects the IEEE802.11b WLAN PCI Card, the Found New
Hardware Wizard window appears. Select Install the software automatically
[Recommended] and insert the driver CD-ROM into CD-ROM drive and click
Next to continue.
19
WLAN PCI Adapter User’s Manual
3.
Click Continue Anyway to continue the installation.
4.
The Windows has finished installing software for the device. Click Finish to finish
the installation
Then system will start to install Wireless LAN Utility. Please refer to procedures at
Chapter 4.
20
WLAN PCI Adapter User’s Manual
Chapter 4 – Installing and Using the
Wireless Utility
The following sections cover the IEEE802.11b WLAN PCI Card utility installation and
configuration.
Installation in Windows
After you have installed driver, system will start to install Wireless LAN Utility. Please
follow the steps below to install the utility.
1. Once you see the following screen, click Next to continue.
21
WLAN PCI Adapter User’s Manual
2. The screen will show you the default destination chosen by the utility. Click Next to
continue or click the Browse button to select an alternate destination.
3. The following screen will add program icons to the Program Folder. You may type
a new folder name or select one from the existing folders list. Click Next to
continue or click Back to review or change any settings.
22
WLAN PCI Adapter User’s Manual
4. The following screen shows the current settings, click Next to continue or click
Back to change the Destination Folder in step 3.
5. The following screen shows you the Setup status by percentage.
23
WLAN PCI Adapter User’s Manual
6. The Windows has finished installing Wireless LAN Utility. Click Finish to finish the
installation.
Using Wireless Utility In Windows XP
Wireless LAN Utility
There are two ways to configure IEEE802.11b WLAN PCI Card. One is Wireless LAN
Utility; the other one is Windows Wireless Network Configuration.
Use Windows Wireless Network Configuration
1. Click the right key of the mouse and Exit Wireless LAN Utility.
24
WLAN PCI Adapter User’s Manual
2. Click the Windows Wireless Network Configuration icon.
Windows Wireless Network Configuration
3. The Connect to Wireless Network window pop up as following, the click the
Advanced button.
4.
Make sure “Use Windows to configure my wireless network settings” has
been selected, and then click OK button.
25
WLAN PCI Adapter User’s Manual
5. Click the Windows Wireless Network Configuration icon again to open the Connect
to Wireless Network window.
Windows Wireless Network Configuration
6.
Select an available network and click Connect button.
26
WLAN PCI Adapter User’s Manual
7. The Windows Wireless Network Configuration has been enabled.
Windows Wireless Network Configuration is enabled
Use Wireless LAN Utility
1. Exit the Wireless LAN Utility.
2. Double click Windows Wireless Network Configuration icon.
Windows Wireless Network Configuration
27
WLAN PCI Adapter User’s Manual
3. Click Advanced button.
4. Disable “Use Windows to configure my wireless network settings” and click
OK button.
28
WLAN PCI Adapter User’s Manual
5. Select Start -> All Programs -> IEEE802.11b WLAN PCI Card then click
IEEE802.11b WLAN PCI Card Utility to start the Wireless LAN Utility.
6. The Wireless LAN Utility will be enabled.
Wireless LAN Utility
29
WLAN PCI Adapter User’s Manual
Use Wireless LAN Utility In Windows 98, 2000 and ME
Wireless LAN Utility icon
Icon
Meaning
Green: indicates a connection is linked
to a wireless network.
Red: indicates that the wireless LAN
card is looking for an available access
point.
Double-click the icon to open the Wireless LAN Utility.
Configuring the IEEE802.11b WLAN PCI Card
1. This screen shows you the status of your current connection. Click Re-Scan to
search for wireless connection (the Card will search for the connection
automatically when it is activated).
2. Select the “Configuration” tab. The profile setting allows you to save
30
WLAN PCI Adapter User’s Manual
configurations in different profiles for different working environments. The default
profile will contain the initial configuration setting when you install the Card. Under
the Operating Mode drop-box, you may choose either Infrastructure or Ad-Hoc.
The Infrastructure mode allows a wireless adapter to communicate with a wired
network employing an Access Point, while the Ad-Hoc mode allows
wireless-to-wireless, peer-to-peer communication. If you choose Infrastructure, the
SSID should have the same name as the Access Point. If you choose Ad-Hoc, all
clients should share the same SSID name. You may also select which Transfer
Rate you wish to use: 1, 2, 5.5, 11Mbps or Auto Rate. Under Power Saving
Mode, you can select Enabled to allow your adapter to go to sleep mode while the
Card doesn’t proceed the data transmission. Or select Disabled to make the Card
never go to sleep mode. Click Apply to save the settings.
3. Select the “Site Survey” tab. The list on the adjacent screen shows you available
Access Points and their features. Click on the desired Access Point, then click
Connect to connect or Search to search for more Access Points. Click OK when
you are finished.
31
WLAN PCI Adapter User’s Manual
4. Click on the “Encryption” tab. Under the drop-box, you can choose to have WEP
encryption Disabled, 64-Bit, or 128-Bit. Wired Equivalent Privacy (WEP) is an
encryption scheme used to protect wireless data communication. The Disabled
setting prevents the sharing of data with other computers on the WEP network. For
data sharing to be enabled, select the level of encryption desired, either 64 or
128-bit.
32
WLAN PCI Adapter User’s Manual
5. Select the “Advanced” tab. You can choose the fragmentation threshold to
define the maximum data frame size your adapter will transmit. When the packet
error rate is high, you may set the threshold value to transmit shorter frames. You
may select RTS/CTS threshold to define when will your adapter send out
RTS/CTS frames to reserve bandwidth for transmission. By using the RTS/CTS
function, you may request bandwidth from AP to allow you have better chance to
send out your data. For the Security, it’s only applicable while WEP is enabled.
For the Authentication Type, the current supported algorithms are Open System,
Shared Key, and Auto. The algorithm will be invoked when associated to Access
Point. To associate to the desired Access Point you must set the same algorithm
as the one of the desired Access Point. When select Auto mode, the driver can
auto detect the Authentication Type of the Access Point you are going to associate.
You can also select Preamble Type, which is for framing synchronization. The
possible settings are Long and Short. The setting must be the same as the setting
of the Access Point you are going to associate.
33
WLAN PCI Adapter User’s Manual
6. The “About” tab shows you copyright and version information about the driver, the
configuration utility, and the firmware. Click OK to complete the configuration.
34
WLAN PCI Adapter User’s Manual
Chapter 5 – Installing Network Protocols
Protocols are necessary for computers to be recognized on your network. Windows
2000 users need to check their Windows User Guides for protocol installation.
Installing the Network Protocols for Windows 98 and
Millennium
1. From the Start Menu, select Settings and bring up the Control Panel. From the
Control Panel, double-click on the Network icon.
Note: Before adding any network protocols, verify that the protocol is not already
installed. Never install duplicate protocols.
2. Select IEEE802.11b WLAN PCI Card from the list and click the Add button.
35
WLAN PCI Adapter User’s Manual
3. Highlight Protocol and click the Add button.
4. Select Microsoft from the list of “Manufacturers” and TCP/IP from the list of
“Network” Protocols” and click the OK button to finish the installation.
36
WLAN PCI Adapter User’s Manual
37
WLAN PCI Adapter User’s Manual
Appendix A – FAQ
1.
What is IEEE 802.11 standard?
The IEEE 802.11 is a wireless LAN industry standard, and the objective
of IEEE 802.11 is to make sure that different manufactures’ wireless
LAN devices can communicate to each other.
2.
What is WEP?
As described in the IEEE 802.11 standard, WEP (Wired Equivalent
Privacy) is a data privacy mechanism based on a 40 bit shared key
algorithm.
3.
My desktop PC cannot recognize the Wireless Network PCI Adapter.
Please make sure that the Card is inserted into the PCI slot of your
desktop PC properly (check this when the PC is powered off).
And also make sure that the PCI controller is enabled in the BIOS of
your desktop PC.
Try installing the card in a different PCI slot.
4.
In Infrastructure mode, my desktop PC cannot communicate with the
others PCs on the network.
First, make sure that the SSID is same as the others PC.
Check if the WEP is enabled on the Access Point, if it is, set your
Adapter’s WEP the same as the Access Point.
Also check the Access Point’s Authentication Type and Preamble Type
and match those settings.
5.
In ad-hoc mode, my desktop PC cannot communicate with the others
PCs on the network.
Make sure the SSID and the Channel number are the same as other
wireless stations.
Check if WEP settings are the same in all wireless stations.
Check the Network Properties, make sure proper protocol is installed
and File and Printer Sharing is enabled.
38
WLAN PCI Adapter User’s Manual
Appendix B – Specifications
Standards:
IEEE 802.11b
Channels:
11 Channels (US, Canada)
13 Channels (Europe)
14 Channels (Japan)
Antenna:
Dipole antenna with reversed SMA Connector
Frequency:
2.4 to 2.4835GHz (Industrial Scientific Medical Band)
Data Rate:
up to 11Mbps
Operating Ranges:
Indoor (varies depends on the environment):
Up to 50M @ 11Mbps
Up to 80M @ 5.5Mbps
Outdoor (varies depends on the environment):
Up to 150M @ 11Mbps
Up to 300M @ 5.5Mbps
Temperature:
Operating:
Storage:
Humidity:
10% to 90% (non-condensing)
0° ~ 55° C
-25° ~ 70° C
39

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Creator                         : Acrobat PDFMaker 5.0 for Word
Modify Date                     : 2003:06:05 22:03:43+08:00
Create Date                     : 2003:05:14 22:47:45+08:00
Page Count                      : 39
Creation Date                   : 2003:05:14 22:47:45+08:00
Mod Date                        : 2003:06:05 22:03:43+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Metadata Date                   : 2003:06:05 22:03:43+08:00
Title                           : 
Page Mode                       : UseNone
Tagged PDF                      : Yes
EXIF Metadata provided by EXIF.tools
FCC ID Filing: N89-MW302P

Navigation menu